Uniden 2MED-VF-BNC Guide d'installation

Uniden
Marque
Uniden
Modèle
2MED-VF-BNC
Catégorie
Des caméras de sécurité
Taper
Guide d'installation

Ce manuel convient également à

ProSeries
ANALOG CAMERA
INSTALLATION GUIDE
XVR Networks
2MED-VF-BNC
2MED-3.6-BNC
2MED-2.8-BNC-SL
2MTD-2.8-BNC
2MB-VF-BNC
2MB-3.6-BNC
© 2018 Uniden America Corporation
Irving, Texas
Issue 1, April 2018
Uniden surveillance products are not manufactured and/or sold with the intent to be used for illegal
purposes. Uniden expects consumer’s use of these products to be in compliance with all local,
state, and federal law. For further information on video surveillance and audio recording legal
requirements, please consult your local, state and federal ofcials.
Uniden constantly works on improving our products. This includes updating our documentation
with the latest rmware changes. Go to www.uniden.com to nd the latest version of all
documentation.
© 2018 Uniden America Corporation
All rights reserved.
CONTENTS
OVERVIEW .............................................. 5
INSTALL EYEBALL DOME CAMERA ........................ 5
WHAT’S INCLUDED ........................................5
INSTALL CAMERA .........................................5
INSTALL TURRET DOME CAMERA ......................... 6
WHAT’S INCLUDED ........................................6
INSTALL CAMERA .........................................6
INSTALL LARGE BULLET CAMERAS ........................ 7
WHAT’S INCLUDED ........................................7
INSTALL CAMERA .........................................8
INSTALL SMALL BULLET CAMERAS ........................ 9
WHAT’S INCLUDED ........................................9
INSTALL CAMERA .........................................9
ANALOG CAMERA SETUP ................................ 10
OSD Line Controls ......................................................11
Exposure Menu ........................................................11
Backlight Mode Menu ...................................................11
White Balance Menu ....................................................12
Day/Night Switch Menu ..................................................12
Video setting ..........................................................12
Restore factory setting and exit ............................................13
SPECIFICATIONS ....................................... 13
DOME CAMERAS .........................................13
BULLET CAMERAS .......................................14
COMPLIANCE .......................................... 15
FCC PART 15 .............................................15
IC ......................................................15
THREE-YEAR LIMITED WARRANTY ........................ 16
4
5
5
ANALOG CAMERA INSTALLATION GUIDE
OVERVIEW
Uniden’s Analog cameras can be installed in Uniden’s XVR surveillance systems to provide HD
over coax cable service.
EYEBALL DOME TURRET DOME LARGE BULLET SMALL BULLET
2MED-VF-BNC 2MTD-2.8-BNC 2MB-VF-BNC 2MB-3.6-BNC
2MED-3.6-BNC
2MED-2.8-BNC-SL
INSTALL EYEBALL DOME CAMERA
WHAT’S INCLUDED
• IP camera
• Mounting template sticker
• Star-tipped Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
Network cable and power source are not included. SD cards are not included. If you
plan on using the Automatic Network Restoration feature in the NVR, you will need to
purchase an SD card.
INSTALL CAMERA
1. Remove the camera and installation items from the box. Verify that all parts are there.
2. Hold the camera and sleeve steady and unscrew the ring from
the base.
Base
Ring
Camera
Sleeve
3. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker. Install the anchors.
4. Position the base on the template, aligning the screw holes to the anchors, and screw it into
position.
6
5. Connect the network cable tail to the house cabling through the
1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
RJ45
Red - 12VDC (optional)
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
6. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
7. Reassemble the camera, sleeve, and ring. Position the assembly onto the base and adjust
the camera to the correct viewing angle.
As you adjust the camera position, check it through the NVR Preview screen.
8. When the viewing angle is correct, tighten the ring to the base.
As you tighten the ring, keep adjusting the camera as needed.
INSTALL TURRET DOME CAMERA
WHAT’S INCLUDED
• IP camera
• Mounting template sticker
• Star-tipped Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
Network cable and power source are not included. SD cards are not included. If you
plan on using the Automatic Network Restoration feature in the NVR, you will need to
purchase an SD card.
INSTALL CAMERA
1. Remove the camera and installation items from the box. Verify that all parts are there.
7
2. Hold the camera and sleeve steady and unscrew the ring from
the base.
Base
Ring
Camera
Sleeve
3. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker. Install the anchors.
4. Position the base on the template, aligning the screw holes to the anchors, and screw it into
position.
5. Connect the network cable tail to the house cabling through the
1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
RJ45
Red - 12VDC (optional)
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
6. Reassemble the camera unit. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera unit.
7. Screw the camera unit to the base securely enough to adjust
the camera position. Double check the position through the
NVR Preview screen.
Use an oil-free soft brush or blow gently into the camera
dome to clear any dust or dirt.
Set Screw
Location (x2)
8. Tighten the ring to the base. Insert the set screws to lock the camera into position.
INSTALL LARGE BULLET CAMERAS
WHAT’S INCLUDED
• IP camera
• Mounting template sticker
• Camera-specic Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
8
• Rubber plug (grommet) to seal network cable hole
Network cable and power source are not included. SD cards are not included. If you
plan on using the Automatic Network Restoration feature in the NVR, you will need to
purchase an SD card.
INSTALL CAMERA
1. Remove the camera and installation items from the box. Verify that all parts are there.
2. Position the installation template at the location (wall, ceiling, etc). Drill a 1” hole as indicated
on the sticker and install the anchors provided.
3. If your bullet camera is equipped with an SD slot, insert the
SD card now before you install the camera. Unscrew the
rectangular hinged panel and insert the SD card.
SD Card Slot
Reset Button
4. Set the DIP switches in the RJ45 according to the protocol on
the cable tag.
ON
TVI
ON
AHD
ON
Analog
ON
CVI
1 2 1 2 1 2 1 2
White = DIP Switch Position
5. Thread the network cable tail through the grommet and connect
it to the house cabling through the 1” hole. Plug the grommet
into the hole. Using the screws provided, screw the camera
base into position.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
RJ45
Red - 12VDC (optional)
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
6. Loosen screw 1 to rotate the camera and stand up to 360°.
Loosen screw 2 to adjust the camera body up to 90° and screw
3 to fine tune the camera position up to 90°. Loosen Screw 4 to
adjust the sun shade.Check the camera’s position through the
NVR Preview screen as you adjust the camera.
Screw 1
Screw 2
Screw 3
Screw 4
9
7. Unscrew the access cover and swing it open. Unscrew the
adjustment levers just enough to move them and adjust the
image. Check the camera’s focus and clarity through the NVR
Preview screen.
• Zoom - Move lever to the left for Telephoto (zoom in) and to the
right for Fish-Eye (zoom out).
• Focus - Move lever to left and right to adjust focus.
8. Tighten the adjustment lever screws when complete and close
the compartment.
Cover
Focus
Zoom
INSTALL SMALL BULLET CAMERAS
WHAT’S INCLUDED
• IP camera
• Mounting template sticker
• Camera-specic Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
• Rubber plug (grommet) to seal network cable hole
Network cable and power source are not included. SD cards are not included. If you
plan on using the Automatic Network Restoration feature in the NVR, you will need to
purchase an SD card.
INSTALL CAMERA
1. Remove the camera and installation items from the box. Verify that all parts are there.
2. Position the installation template at the location (wall, ceiling, etc). Drill a 1” hole as indicated
on the sticker and install the anchors provided.
3. Thread the network cable tail through the grommet and connect
it to the house cabling through the 1” hole. Plug the grommet
into the hole. Using the screws provided, screw the camera
base into position.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
RJ45
Red - 12VDC (optional)
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
4. Loosen screw 1 to rotate the camera and stand up to 360°.
Loosen screw 2 to adjust the camera body up to 90° and
screw 3 to fine tune the camera position up to 90°. Check the
camera’s position through the NVR Preview screen as you
adjust the camera.
Screw 1
Screw 2
Screw 3
10
5. Once positioned, tighten all screws to secure.
ANALOG CAMERA SETUP
The ProSeries analog cameras connect to the XVR system via a BNC connector (analog video or
Hi-Denition over Coax). Use the Up the Coax (UTC) menus to congure these cameras.
1. Select the Preview icon; live camera views display.
2. Double-click the camera image you want to adjust; a full screen camera view displays.
3. Right-click in the camera view and select UTC Ctl in the pop up menu.
4. A oating window displays the channel number in the title bar.
5. Click Auto button in the center of the directional controls; the MAIN MENU screen displays over
the camera view.
Directional
Arrows
Auto/Enter
button
Menu items with a return arrow ( ) indicate that the menu item has a sub menu. Select the
menu item and then select Auto in the directional controls image. The submenu displays.
MAIN MENU
LENS Manual lens
DC lens
EXPOSURE Electronic shutter DWDR
AGC Defog
Sens-up Return
Brightness
BACKLIGHT Off
HLC
BLC
WHITE LIGHT ATW Outdoor mode
AWC→SET
Manual mode
Indoor mode AWB
DAY/NIGHT
External switch
Color mode
Auto
W/B MODE
NR
2D NR Return
3D NR
11
SPECIAL
Camera name Language
Digital function
Live DPC
Motion detection
RS458
Privacy mask Return
ADJUST
Sharpness
MONITOR OUT
Display screen
NTSC/PAL
LSC
Return
SIGNAL OUTPUT
AHD/THD/CHD/CVBS
EXIT
Save/Exit
Reset
Not save
OSD Line Controls
KEY DESCRIPTION
◄ Press and hold left key of OSD for 5S, camera enters CVBS mode.
► Press and hold right key of OSD for 5S, camera enters AHD mode.
▲ Press and hold up key of OSD for 5S, camera enters CHD mode.
▼ Press and hold down key of OSD for5S, camera enters THD mode.
Press MENU, enter OSD main menu or use this button to enter menu or menu
options.
Use LEFT/RIGHT to move horizontally in menu options.
Use UP/DOWN to move vertically in menu options.
Note: If the camera has a motorized lens, shortcut keys control motorized lens zoom
and focus.
Exposure Menu
KEY DESCRIPTION
Brightness
◄, ►
To improve the current image brightness, move the cursor to the brightness,
press left and right to select and adjust brightness parameters. Optional
parameters value range is 1-100 (default 40).
Hidden menu
►
In the exposure menu, press right for three times then conrm; enter the hidden
menu to switch video mode.
GC
◄, ►
Under low illumination, to increase the image brightness. Move the cursor to
the gain, then press left and right to adjust the gain size. Range is 1-15 (Default
= 15).
Backlight Mode Menu
KEY DESCRIPTION
BLC
◄, ►
To improve the current image brightness, move the cursor to the brightness
and press left and right to select and adjust brightness parameters. Optional
parameters value range is 1-100 (Default = 40).
HLC
▲, ▼
In strong light conditions, adjust brightness (too bright which will cause
overexposure).
12
KEY DESCRIPTION
WDR
▲, ▼
Open ultra WDR to effectively adjust the image brightness.
On/Off
▲, ▼
On/Off (Default = Off)
White Balance Menu
KEY DESCRIPTION
ATW
▲, ▼
Adjust white balance parameters according to current conditions.
Manual Mode
▲, ▼
Manually adjust white balance parameters, blue/red gain according to current
conditions.
Indoor Mode
▲, ▼
AWB
▲, ▼
AWC
▲, ▼
Day/Night Switch Menu
The Day/Night switch has 4 settings; press left/right to switch between them.
KEY DESCRIPTION
External switch
mode
▲, ▼
Under external switch mode, photoresistance feels light intensity, control IR
open, switch black and white mode.
Automatic
Mode
▲, ▼
Automatic mode adjusts AGC value to adapt to current conditions.
Color Mode
▲, ▼
Color mode sets the image to color.
B/W Mode
▲, ▼
B/W mode changes the image to black and white and adjusts IR PWM size
according to actual conditions.
Note: IR camera default external switch mode, non-IR camera default automatic.
Video setting
Adjust brightness, sharpness, digital NR parameters In the practical application, reach the
ideal image effect.
KEY DESCRIPTION
Brightness
◄, ►
Exposure->brightness, left/right switch can adjust the brightness of the whole
image, optional parameters range is 1-100. (Default = 40)
Sharpness
◄, ►
Adjust->sharpness, left/right switch can change the sharpness of objects edge
optional parameters range is 0-10. (Default = 6).
Saturation
◄, ►
Adjust->display screen, left/right switch red/blue gain value, make the image
fuller, optional parameters range is 1-100.
Digital NR
◄, ►
Main menu 2D and 3D two NR mode, Range is Low/Middle/High (Default =
Middle).
Mirror
◄, ►
Function->digital function, left/right switch can realize image interchange of
left and right, turn upside down and central symmetry effect,etc, often used
in image correction of the camera non-horizontal installation. (default = Off).
13
Restore factory setting and exit
KEY DESCRIPTION
Restore Factory
Settings
◄, ►
Move the cursor to the exit, left/ght switch to reset, press conrm to restore
the parameters setting to the default.
Save and Exit
◄, ►
Move the cursor to the exit, press conrm to exit the current menu setting, then
save previous parameters setting.
Note: Video mode, system, language can’t restore factory default.
Connection schematic diagram
SPECIFICATIONS
DOME CAMERAS
2MED-VF-BNC 2MED-3.6 2MMD-2.8 2MTD-2.8
GENERAL
IR Distance 100’ Night Vision (36xΦ5 LEDs) 100’ Night
Vision (6X Array
IR LEDs)
30-50’ Night
Vision
(1X Array IR
LEDs)
Protection Grade IP65 IP66 IP65
Power 12VDC ± 10%
Power Jack 2.1mm Power Jack for optional 12VDC input
Power
Consumption
<3.9W (IR LEDs +main board:
0.96W)
<6W
Operating Temp -4°F~131°F
(-15.5°C~55°C)
-14°F~122°F
(-9.7°C~50°C)
-4°F~131°F
(-15.5°C~55°C)
-14°F~122°F
(-9.7°C~50°C)
14
2MED-VF-BNC 2MED-3.6 2MMD-2.8 2MTD-2.8
Operating Humidity 0% - 90%
Dimensions (inch) 4.72(L) x 4.72(W) x 3.74(H) 4.61 (L) x 4.61
(W) x 2.6 (H)
3.28 (L) x 3.28
(W) x 3.66 (H)
CAMERA
Sensor 1/2.9” SONY 2MP CMOS
Video Frame Rate 1080p@25/30fps 1920 (H) x 1080 (V) ------- -------
Resolution 1280H (CVBS
output)
1920 x 1080
Min. Illumination 0 Lux (IR ON) 0 Lux/ F1.4 (IR ON) 0 Lux/ F1.4 (IR
ON)
Lens 2.8-12mm M14
Lens, standard ICR
module
3.6mm ICR Lens 2.8mm Fixed
Electronic Shutter Auto/Manual
(X30~1/50000)/FLK
Auto/Manual
(1/25~1/10000), FLK
R/N Ratio ≥ 50db (AGC OFF)
Video Output 1.0Vp-p complex
video output, 75Ω
Output Model PAL/NTSC
adjustable
BULLET CAMERAS
2MB-VF 2MB-3.6
GENERAL
IR Distance 130-165’ Night
Vision
(3xIR-III LEDs)
100’ Night Vision
(36xΦ5 LEDs)
Protection Grade IP66
Power
Power Jack 2.1mm Power Jack for optional 12VDC
input
Power
Consumption
<9W <6W
Operating Temp -4°F~131°F
(-15.5°C~55°C)
Operating Humidity 0% - 90%
Dimensions (in.) 10.35 (L) x 3.66
(W)* x 3.76 (H)
6.56( L) x 2.60 (W)
x 2.60 (H)
CAMERA
Sensor 2.9” SONY 2.07 MP
Progressive
Effective Pixels 1920 (H) x 1080 (V)
Video Frame Rate 1080P@25/30fps
Resolution 1920 x 1080
Min. Illumination 0Lux/F1.4 (IR ON)
Lens 2.8-12mm varifocal
lens
3.6mm
15
2MB-VF 2MB-3.6
Electronic Shutter Auto/Manual (1.25 - 1/10000), FLK
R/N Ratio ≥ 50db (AGC OFF)
Video Output 1CH 1.0V p-p
complex video output
Output Model PAL/NTSC adjustable
COMPLIANCE
FCC PART 15
The equipment has been tested and found to comply with the limits for a Class B device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment. Any change or modication must be approved in
writing by Uniden.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Tout changement ou modication non approuvé expressément par la partie responsable pourrait
annuler le droit à l’utilisateur de faire fonctionner cet équipement. Tout changement ou modication
doit être approuvé par écrit par Uniden.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à l’article 15 des
règlements de la Commission fédérale des communications (FCC). Ce dispositif est soumis
aux conditions suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et; 2)
Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites pouvant nuire à son
fonctionnement.
In order to comply with FCC RF Exposure requirements, this device must be installed to provide at
least 7.9 in (20 cm) separation from the human body at all times.
IC
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux normes CNR d’Industrie Canada destinés aux appareils radio
exempts de licence. Son fonctionnement est soumis aux deux conditions suivantes :
16
1) Cet appareil ne doit pas causer d’interférences nuisibles et;
2) Il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement
normal.
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to
provide at least 7.9 in. (20 cm) separation from the human body at all times.
An de se conformer aux exigences d’exposition RF FCC/ISED, ce dispositif doit être installé pour
assurer une séparation d’au moins 20 cm du corps humain à tout moment.
THREE-YEAR LIMITED WARRANTY
Important: SAVE YOUR RECEIPT! Evidence of original purchase is required for warranty service.
WARRANTOR: Uniden America Corporation (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants,
for three years, to the original retail owner, this Uniden Product to be free from defects in materials &
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect 36
months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modied, altered, or used as part of any conversion kits,
subassemblies, or any congurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired
by someone other than an authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured
by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time
while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit &
return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by
warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option,
may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING
TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states
do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or
exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, & you may also have other rights which
vary from state to state. This warranty is void outside the United States of America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in
the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably
in its original packaging). The Product should include all parts & accessories originally packaged with the
Product. Include evidence of original purchase & a note describing the defect that has caused you to return
it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henrietta Creek Rd., Suite 100
Roanoke, TX 76026
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Uniden 2MED-VF-BNC Guide d'installation

Uniden
Marque
Uniden
Modèle
2MED-VF-BNC
Catégorie
Des caméras de sécurité
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents