Yealink W56H Guide de démarrage rapide

Quick Start Guide(V80.18)

www.yealink.com

Applies to ﬁrmware version 25.80.0.15 or later.

IP DECT Phone

W56P & W56H

English | Deutsch | Español | Français

Table of Contents

English ..........................................1

Deutsch .....................................15

Español ......................................30

Français .....................................44

1

Packaging Contents

The following items are included in your W56P package:

W56H Handset Base for W52P/W56P USB Charger Cradle Two Power Adapters

Belt Clip Ethernet Cable Rechargeable Battery Quick Start Guide

Note:

Yealink W56P IP DECT phone consists of one Base for W52P/W56P and one W56H Handset.

The following items are included in your W56H package:

W56H Handset USB Charger Cradle Power Adapter Belt Clip Rechargeable Battery

Note:

We recommend that you use the accessories provided or approved by Yealink. The use of

unapproved third-party accessories may result in reduced performance.

E

N

G

L

I

S

H

2

E

N

G

L

I

S

H

1. Connect the network and power for the base station in one of the following ways,

as shown below:

a. AC Power Option

The following item is optional accessory:

W56P Handset Protective Case

2. Insert the battery into the handset, as shown below:

b. PoE (Power over Ethernet) Option

Assembling the DECT Phone

Note:

If inline power (PoE) is provided, you do not need to connect the power adapter. Make

sure the hub/switch is PoE-compliant. The base station should be used with original

power adapter (5V/600mA) only. The use of the third-party power adapter may cause

the damage to the base station.

Note: You need to purchase separately if required.

battery

IEEE 802.3af compliant

PoE Hub/Switch

3

3. Connect the charger cradle and charge the handset, as shown below:

Note:

The handset should be used with original power adapter (5V/600mA) only. The use of the third-

party power adapter may cause the damage to the handset.

The charging status of the handset is indicated in the top right-hand corner of the LCD screen.

4. (Optional) Mount the charger cradle on the wall, as shown below:

36.00mm

1:1

36mm

5. Attach the Belt Clip, as shown below:

E

N

G

L

I

S

H

4

Getting Started

Shortcuts

This helps you get quick access to features by pressing the shortcut keys directly without having to scroll

through the menu.You can press the following predeﬁned shortcut keys to access some frequently used

features when the handset is idle:

2

5

6

1

3

4

1

Press the left soft key to access the call history.

2

Press the right soft key to check the line status.

3

Press



to place an internal call.

4

Press



to decrease the ringer volume.

5

Press



to increase the ringer volume.

6

Press



to access the directory.

Entering and Editing Data

Press one or more times to switch among input modes or enter “#”.

Press to select the special characters or enter “*”.

Press a digit key one or more times to enter the desired character or digit.

Press the

Del

soft key to delete entered characters.

Press the

Save

soft key to accept the change or to cancel.

Handset Registration

1. Do one of the following to register your handset manually:

Long press on the base station till the registration LED slow ﬂashes. Then press the

OK

key to

enter the main menu on the handset, select

Settings->Registration->Register Handset

.

If the handset LCD screen prompts “Press base page 2s then press OK”, long press on the base

station till the registration LED slow ﬂashes. Then press the

OK

soft key on the handset, select

Register

Handset

.

E

N

G

L

I

S

H

You can register up to 5 handsets to one base station. Each handset can be registered to 4 diﬀerent base

stations.

5

2. Select the desired base and press the

OK

soft key. The handset begins searching the base.

3. Press the

OK

soft key after searching a base successfully.

4. Enter the base PIN (default: 0000), and then press the

Done

soft key to complete registeration.

Note:

After the success of registration, the handset LCD screen prompts “Handset subscribed”.

If the handset LCD screen prompts “Searching for Base”, please check your base station if

powered on.

Network Settings

You can conﬁgure the base station to obtain network settings in one of the following ways:

DHCP:

By default, the base station attempts to contact a DHCP server in your network to obtain the valid

network settings, e.g., IP address, subnet mask, gateway address and DNS address.

Static IP Address:

If the base station cannot contact a DHCP server for any reason, you need to conﬁgure

the IP address, subnet mask, gateway address, primary DNS address and secondary DNS

address for the base station manually.

PPPoE:

If you are using an xDSL modem, you can connect your base station to the Internet via PPPoE

mode. Contact the ITSP for the account and password.

To conﬁgure the network parameters for the base station manually:

1. Press the

OK

key to enter the main menu, and then select

Settings->System Settings ->Network.

2. Enter the system PIN (default: 0000), and then press the

Done

soft key.

5. Make the desired changes.

6. Pr

ess the

Save

soft key to accept the change.

Note:

The IP DECT phone supports either or both IPv4 and IPv6 addresses mode, but IPv6 is disabled by default.

E

N

G

L

I

S

H

4. Press to select the corresponding IP address mode.

3. Select the desired IP address mode from the IP Mode ﬁeld.

Wrong network settings may result in inaccessibility of your DECT phone and may have an impact on

the network performance. For more information on these parameters, contact your system

administrator.

6

Basic Operations

Turning Handset On/Oﬀ

To turn the handset on, do one of the following:

Press , then the LCD screen lights up.

Place the handset in the charger cradle. The handset will be turned on automatically.

To turn the handset oﬀ:

Long press

to turn the handset oﬀ.

Locking/Unlocking Keypad

Long press when the handset is idle to lock the keypad.

Long press again to unlock the keypad.

Silent Mode

Long press when the handset is idle to switch the silent mode to On.

Long press again to switch the silent mode to Oﬀ.

Handset Settings

Handset Name

To rename the handset:

1. Press the

OK

key to enter the main menu, and then select

Settings->Handset Name

.

2. Edit the value in the

Rename

ﬁeld.

3. Press the

Save

soft key to accept the change.

Volume Adjustment

Press



or



when the handset is idle to adjust the ringer volume.

Press



or



during a call to adjust the receiver volume of speakerphone/earpiece.

E

N

G

L

I

S

H

7

Ring Tones

1. Press the

OK

key to enter the main menu, and then select

Settings->Audio->Ring Tones ->Melodies

.

2. Press



or



to highlight the

Intercom Call

option or the desired line.

3. Press



or



to select the desired ring tone.

4. Press the

Save

soft key to accept the change.

Local Directory

To add a contact:

1. Press the

OK

key to enter the main menu, and then select

Directory

.

2. Press



or



to highlight the desired entry.

3. Press the

Options

soft key, and then select

Edit

.

4. Edit the value in the

Name, Number

and

Mobile

ﬁeld respectively.

5. Press the

Save

soft key to accept the change.

To delete a contact:

1. Press the

OK

key to enter the main menu, and then select

Directory.

2. Press



or



to highlight the desired entry.

3. Press the

Options

soft key, and then select

Delete

to delete the selected entry.

To assign a speed dial number:

1. Press the

OK

key to enter the main menu, and then select

Settings->Telephony->Speed Dial

.

2. Press



or



to highlight the desired digit key, and then press the

Assign

soft key.

3. Press



or



to highlight the desired entry, and then press the

OK

soft key.

If both the oﬃce number and mobile number are stored, press



or



to highlight the desired

number, and then press the

OK

soft key again.

E

N

G

L

I

S

H

8

Basic Call Features

Placing Calls

To place a call directly:

1. Do one of the following:

Enter the desired number when the handset is idle.

Press to enter the pre-dialing screen.

Enter the desired number using the keypad.

If there are multiple lines assigned to your handset as outgoing lines, press the

Line

soft key to select

the desired line. If you do not select a line, the handset uses the default outgoing line to dial out.

2. Press

, or to dial out.

To place a call from the local directory:

1. Press



when the handset is idle.

2. Press



or



to highlight the desired entry, and then press

or to dial out using the default line.

If multiple numbers for the contact are stored, press



or



to highlight the desired number, and

then press

or again to dial out using the default line.

To place a call from the call history:

1. Press the

History

soft key when the handset is idle, and then select the desired call history list.

2. Press



or



to highlight the desired entry, and then press

or to dial out using the default line.

To place a call from the redial list:

1. Press

or when the handset is idle.

2. Press



or



to highlight the desired entry, and then press

or .

To place a call using the speed dial key:

Long press the speed dial key to place a call to preset number directly.

E

N

G

L

I

S

H

9

Answering Calls

To answer a call, do one of the following:

Press the

Accept

soft key.

Press .

Note:

You can ignore an incoming call by pressing the

Silence

soft key or reject an incoming call by

.

Ending Calls

Press .

Call Mute

Press during a call to mute the call.

Press again to un-mute the call.

Call Hold and Resume

To place a call on hold:

Press the

Options

soft key during a call, and then select

Hold

.

To resume a call, do one of the following:

If there is only a call on hold, press the

Resume

soft key.

If there are two calls on hold, press the

Resume

soft key to resume the current call.

Press the

Swap

soft key to swap between calls.

Call Transfer

You can transfer a call in the following ways:

Blind Transfer

1. Press the

Options

soft key during a call, and then select

Transfer

.

E

N

G

L

I

S

H

pressing

10

2. Enter the number you want to transfer the call to.

3. Press the

Transfer

soft key.

Semi-Attended Transfer

1. Press the

Options

soft key during a call, and then select

Transfer

.

2. Enter the number you want to transfer the call to.

3. Press

, or to dial out.

4. Press the

Transfer

soft key when you hear the ring-back tone.

Attended Transfer

1. Press the

Options

soft key during a call, and then select

Transfer

.

2. Enter the number you want to transfer the call to.

3. Press

, or to dial out.

4. Press the

Transfer

soft key after the call is answered.

Call Forward

To enable the call forward feature on a speciﬁc line:

1. Press the

OK

key to enter the main menu, and then select

Call Features->Call Forward

.

2. Press



or



to highlight the desired line, and then press the

OK

soft key.

3. Press



or



to highlight the desired forwarding type, and then press the

OK

soft key.

Always----Incoming calls are forwarded immediately.

Busy----Incoming calls are forwarded when the line is busy.

No Answer----Incoming calls are forwarded if not answered after a period of time.

4. Select

Enabled

from the

Status

ﬁeld.

5. Enter the number you want to forward the incoming calls to in the

Target

ﬁeld.

For

No Answer Forward

, press



or



to select the desired ring time to wait before forwarding in the

After

Ring Time

ﬁeld.

6. Press the

Save

soft key to accept the change.

E

N

G

L

I

S

H

11

Safety Instructions

Save these instructions. Read these safety instructions before use!

To reduce risk of ﬁre, severe personal injury and damage to property, read the following safety

information carefully before using the product.

Environmental Requirements

Place the product on a stable, level and non-slip surface.

Do not place the product close to heat sources, in direct sunlight or next to any household

appliance with strong magnetic ﬁeld or electromagnetic ﬁeld, such as a microwave oven or a

refrigerator.

Do not allow the product to come into contact with water, dust and chemicals.

Protect the product from aggressive liquids and vapors.

Do not place the product on or near any inﬂammable or ﬁre-vulnerable object, such as rubber-

made materials.

Do not install the product in rooms with high humidity, for example, in bathrooms, laundry rooms

and wet basements.

Safety Notes During Operation

Use only spare parts and accessories supplied or authorized by Yealink. The operation of non-

authorized parts cannot be guaranteed.

Do not place heavy objects on top of the handset or the base station in case of damage and

deformation caused by the heavy load.

Do not open the handset or the base station by yourself for repair purpose, which could expose

you to high votages. Have all repairs carried out by authorized service personel.

Do not let a child operate the product without guidance.

Keep the small accessories contained in your product out of reach of small children in case of

accidental swallowing.

Before plugging or unplugging any cable, make sure that your hands are completely dry.

Do not hold the handset up to your ear when speakphone is on or when the ringer is ringing as

the volumn can be very loud, which may be harmful to your hearing.

During a thunderstorm, stop using the product and disconnect it from the power supply to avoid

lightning strike.

E

N

G

L

I

S

H

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Tel: +86-592-5702000

Fax: +86-592-5702455

12

If the product is left unused for a rather long time, disconnect the base station from the power

supply and unplug the power adapter.

When there is smoke emitted from the product, or some abnormal noise or smell, disconnect the

product from the power supply, and unplug the power adapter immediately.

Remove the electrical cord from an outlet by pulling gently on the power adapter, not by pulling

the cord.

Battery Precautions

Do not immerse the battery into water, which could short-circuit and damage the battery.

Do not expose the battery to an open ﬂame or leave the battery where it could be subjected to

extremly high temperatues, which could cause the battery to explode.

Do power the handset oﬀ before removing the battery.

Do not try to use the battery for the power supply of any device other than this handset.

Do not open or mutilate the battery, released electrolyte is corrosive and may cause damage to the

your eyes or skin.

Use only the rechargeable battery pack delivered with the handset or those rechargeable battery

packs expressly recommended by Yealink.

Defective or exhausted battery should never be disposed of as municipal waste. Return old battery

to the battery supplier, a licensed battery dealer or a designated collection facility.

Notices of Cleaning

Before cleaning the base station, stop using it and disconnect it from the power supply.

Remove the battery before cleaning the handset to reduce risk of electric shock.

Only clean your product with a piece of slightly moist and anti-static cloth.

Keep the power plug clean and dry. Using a dirty or wet power plug may lead to electric shock or

other perils.

E

N

G

L

I

S

H

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Tel: +86-592-5702000

Fax: +86-592-5702455

13

ENVIRONMENTAL RECYCLING

Never dispose of the device with domestic waste

Ask your Town Council about how to dispose of it in an environmentally friendly way.

The cardboard box, plastic packaging and player components may be recycled in

accordance with prevailing recycling regulations in your country.

Always adhere to prevailing regulations

Those who fail to do so may be ﬁned or prosecuted in accordance with the law.

The crossed out garbage can that appears on the device means that when it has

reached the end of its useful life, it should be taken to a special waste disposal centre

and treated separately to general urban waste.

Batteries: Be sure that the batteries have been placed in the right position. This phone use rechargeable

batteries only.

Compulsory information according to regulations for battery-operated devices. Caution: Risk of explosion

if battery is replaced with a battery of a wrong kind. Dispose of batteries in accordance with the

instructions.

E

N

G

L

I

S

H

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Tel: +86-592-5702000

Fax: +86-592-5702455

Declaration of Conformity

We,

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD,

Address: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

CE DATE: 17th/July/2017

declare that the product

Type: IP DECT Phone

Model: W56P/W56H

meets the essential requirements and other relevant provisions according to the following EC directive

Directive: Radio Equipment Directive 2014/53/EU;

The presumption of conformity with the essential requirement is ensure according to:

Article 3.1 a : (protection of the health &the safety of the user)

Safety: EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

SAR: EN62479:2010

Article 3.1 b : (protection requirement with respect to electromagnetic compatibility)

EMC: ETSI EN 301489-1 V2.2.0 & ETSI EN 301489-6 V2.2.0

Article 3.2 (eﬀective use of the radio spectrum)

Radio: ETSI EN 301406 V2.2.2

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD

WWW.YEALINK.COM

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Tel: +86-592-5702000

Fax: +86-592-5702455

14

YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.

Address: Strawinskylaan 3127, Atrium Building, 8th ﬂoor,

1077ZX Amsterdam, the Netherlands

Telephone: +31(0)646111373

Email: [email protected]

Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the

restriction of the use of certain hazardous substances in electrical and

electronic equipment (RoHS)

Directive 2002/96/EC of the European Parliament and of the Council of 27.01.2003 on Waste

electrical and electronic equipment(WEEE)

15

Verpackungsinhalt

Folgende Teile sind im Lieferumfang Ihres W56P enthalten:

W56H-Mobilteil Basisstation für W52P/W56P USB-Ladeschale Zwei Netzteile

Gürtelclip Ethernet-Kabel

Wiederauﬂadbare

Batterie

Kurzanleitung

Hinweis:

Das Yealink IP DECT phone W56P besteht aus einer Basisstation für W52P/W56P und einem

Handset W56H.

Folgende Teile sind im Lieferumfang des W56H enthalten:

W56H-Mobilteil USB-Ladeschale Netzteil Gürtelclip

Wiederauﬂadbare

Batterie

Hinweis:

Wir empfehlen, nur von Yealink angebotenes oder zugelassenes Zubehör zu verwenden. Die

Verwendung von nicht zugelassenem Zubehör von Drittanbietern kann sich negativ auf die

Leistung auswirken.

D

E

U

T

S

C

H

Das DECT-Telefon zusammensetzen

1. Verbinden Sie die Basisstation mit dem Netzwerk und der Stromversorgung auf eine

der nachfolgend beschriebenen Weisen:

PoE Netzwerk-Switch

a. AC-Stromversorgung b. PoE (Power over Ethernet)

Hinweis:

Bei Inline-Stromversorgung (PoE) muss das Netzteil nicht angeschlossen werden. Vergewissern

Sie sich, dass der Netzwerk-Switch PoE-kompatibel ist. Die Basisstation darf nur mit dem originalen

Netzteil (5 V/600 mA) betrieben werden. Bei Verwendung eines Drittanbieter-Netzteils kann die

Basisstation beschädigt werden.

2. Legen Sie die Batterie wie unten dargestellt in das Mobilteil ein:

Akku

Schutzetui für das Handset W56P

Hinweis: Falls Sie das Schutzetui benötigen, müssen Sie es separat erwerben.

Der folgende Artikel ist optionales Zubehör:

D

E

U

T

S

C

H

16

17

3. Schließen Sie die Ladestation an und laden Sie das Mobilteil wie unten dargestellt auf:

Hinweis:

Das Mobilteil darf nur mit dem originalen Netzteil (5 V/600 mA) betrieben werden. Bei

Verwendung eines Drittanbieter-Netzteils kann das Mobilteil beschädigt werden.

Der Ladestatus des Mobilteils wird oben rechts im Display angezeigt.

4. (Optional) Befestigen Sie die Ladestation wie unten dargestellt an der Wand:

36.00mm

1:1

36mm

5. Befestigen Sie den Gürtelclip wie unten dargestellt:

D

E

U

T

S

C

H

18

Erste Schritte

Schnellzugriﬀstasten

Sie können Funktionen schnell aufrufen, indem Sie auf die Schnellzugriﬀstasten drücken, statt endlos

durch das Menü zu scrollen. Beﬁndet sich das Mobilteil im Bereitschaftszustand, können Sie die folgenden

voreingestellten Schnellzugriﬀstasten drücken, um einige häuﬁg verwendete Funktionen aufzurufen:

2

5

6

1

3

4

1

Drücken Sie den linken Softkey, um das Anrufprotokoll

anzuzeigen.

2

Drücken Sie den rechten Softkey, um den Status der Leitung

zu überprüfen.

3

Drücken Sie



, um einen internen Anruf zu tätigen.

4

Drücken Sie



, um die Lautstärke des Klingeltons zu reduzieren.

5

Drücken Sie



, um die Lautstärke des Klingeltons zu erhöhen.

6

Drücken Sie



, um das Telefonbuch aufzurufen.

Daten eingeben und bearbeiten

Drücken Sie einmal oder mehrere Male, um zwischen den Eingabemodi umzuschalten, oder

drücken Sie „#“.

Drücken Sie , um Sonderzeichen auszuwählen, oder drücken Sie „*“.

Drücken Sie eine Ziﬀerntaste einmal oder mehrere Male, um das gewünschte Zeichen oder die

gewünschte Ziﬀer einzugeben.

Drücken Sie die

Del

-Taste, um eingegebene Zeichen zu löschen.

Drücken Sie die

Save

-Taste, um die Änderung zu übernehmen, oder , um sie zu verwerfen.

Das Mobilteil anmelden

Sie können bis zu fünf Mobilteile an der Basisstation anmelden. Jedes Mobilteil kann an vier

verschiedenen Basisstation angemeldet werden.

1. Gehen Sie wie folgt vor, um das Mobilteil manuell anzumelden:

Halten Sie die Taste an der Basisstation gedrückt, bis die Anmelde-LED blinkt. Drücken Sie dann

die

OK

-Taste, um das Hauptmenü des Mobilteils aufzurufen, und wählen Sie

Settings->Registration->

Register Handset

.

D

E

U

T

S

C

H

La page charge ...

Yealink W56H Guide de démarrage rapide

Ce manuel convient également à

Yealink W56H Guide de démarrage rapide

dans d''autres langues

Documents connexes