MTD 11A-083F800 Le manuel du propriétaire

Marque: MTD

Modèle: 11A-083F800

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Operator's Manual

22" Rotary Mower

Model Series 080

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting

applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have

similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized

service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

ForUSCustomers:MTD LLC, P.O.BOX361131,CLEVELAND,OHIO44136-0019

ForCanadian Customers: MTDProducts Ltd., P. O.BOX1386, KITCHENER,ONTARION2G4J1

PRINTED IN U.S.A.

FORM NO. 769-01440

(10/2004)

TABLEOFCONTENTS

Content Page

Customer Support 2

Important Safe Operation Practices 3

Slope Gauge 5

Setting Up 6

Operating Your Lawn Mower 8

Content Page

Adjustments 10

Maintenance 11

Troubleshooting 13

Parts List 14

Warranty 16

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new equipment. Itwill help you assemble, prepare and maintain the unit for

best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the equipment and copy the

information from it in the space provided below. A sample model plate is also given below. You can locate the model

plate by standing at the operating position and looking down at the rear of the deck. This information wilt be

necessary to use the manufacturer's web site and/or help from the Customer Support Department or an authorized

service dealer.

Model Number Serial Number

Num#ro de module Num#ro de s#rier

XXXXXXXXXXX XXXXXXXXXXX

MTD LLC

CLEVELAND, OH 44136

MTD PRODUCTS LIMITED

KITCHENER, ON N2G 4J1

USA-www.mtdproducts.com 1-800-800-7310

CAN-www.mtdcanada.com 1-800-668-1238

Copy the model number here:

Copy the serial number here:

ENGINEINFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifications,

warranty and service. Please refer to the engine manufacturer's Owner's/Operator's Manual packed separately with your unit for

more information.

CALLINGCUSTOMERSUPPORT

Please doNOTreturnthe unitto the retailer fromwhichit waspurchased,withoutfirstcontactingCustomerSupport.

Ifyou have difficulty assembling this product or have any questions regarding the controls, operation or maintenance

of this unit, please call a Customer Support Representataive.

For US Customers: 1- (330) 220-4MTD (4683) or 1- (800)-800-7310

For Canadian Customers: 1-800-668-1238

Please have your unit's model number and serial number ready when you call. See previous section to locate this information.

You will be asked to enter the serial number in order to process your call.

HOWTOOBTAINSERVICE

Warranty service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To

locate the dealer in your area;

In the U.S.A.: Check your Yellow Pages, or contact MTD LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or

call 1-800-800-7310 or 1-330-220-4683 or log on to our Web site at www.mtdproducts.com.

In Canada: Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-668-1238 or log on to our Web

site at www.mtdcanada.com.

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES

WARNING" This symbol points out important safety instructions which, if not followed, could

endanger the personal safety and/or property of yourself and others. Read and follow all instructions in

this manual before attempting to operate this machine. Failure to comply with these instructions may

result in personal injury. When you see this symbol - heed its warning.

WARNING" Engine Exhaust, some of its constituents, and certain vehicle components contain or

emit chemicals known to State of California to cause cancer and birth defects or other reproductive

harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this

manual. As with any type of power equipment, carelessness or error on the part of the operator can

result in serious injury. This machine is capable of amputating hands and feet and throwing objects.

Failure to observe the following safety instructions could result in serious injury or death.

GeneralOperation

1. Read this operator's manual carefully in its entirety before

attempting to assemble this machine. Read, understand, and

follow all instructions on the machine and in the manual(s)

before operation. Be completely familiar with the controls and

the proper use of this machine before operating it. Keep this

manual in a safe place for future and regular reference and for

ordering replacement parts.

2. This machine is a precision piece of power equipment, not a

plaything. Therefore, exercise extreme caution at all times. Your

unit has been designed to perform one job: to mow grass. Do not

use it for any other purpose.

3. Never allow children under 14 years old to operate this machine.

Children 14 years old and over should read and understand the

instructions in this manual and should be trained and supervised

by a parent. Only responsible individuals who are familiar with

these rules of safe operation should be allowed to use this

machine.

4. Thoroughly inspect the area where the equipment is to be used.

Remove all stones, sticks, wire, bones, toys and other foreign

objects which could be tripped over or picked up and thrown by

the blade. Thrown objects can cause serious personal injury.

Plan your mowing pattern to avoid discharge of material toward

roads, sidewalks, bystanders and the like. Also, avoid

discharging material against a wall or obstruction which may

cause discharged material to ricochet back toward the operator.

5. To help avoid blade contact or a thrown object injury, stay in the

operator zone behind the handles and keep children,

bystanders, helpers and pets at least 75 feet from the mower

while it is in operation. Stop machine if anyone enters the area.

6. Always wear safety glasses or safety goggles during operation

and while performing an adjustment or repair to protect your

eyes. Thrown objects which ricochet can cause serious injury to

the eyes.

7. Wear sturdy, rough-soled work shoes and close-fitting slacks

and shirts. Shirts and pants that cover the arms and legs and

steel-toed shoes are recommended. Never operate this machine

in bare feet, sandals, slippery or light weight (e.g. canvas) shoes.

8. Do not put hands or feet near rotating parts or under the cutting

deck. Contact with the blade can amputate hands and feet.

9. A missing or damaged discharge cover can cause blade contact

or thrown object injuries.

10. Many injuries occur as a result of the mower being pulled over

the foot during a fall caused by slipping or tripping. Do not hold

on to the mower if you are falling; release the handle

immediately.

11. Never pull the mower back toward you while you are walking. If

you must back the mower away from a wall or obstruction first

look down and behind to avoid tripping and then follow these

steps:

a. Step back from the mower to fully extend your arms.

b. Be sure you are well balanced with sure footing.

c. Pull the mower back slowly, no more than half way

toward you.

d. Repeat these steps as needed.

12. Do not operate the mower while under the influence of alcohol

or drugs.

13. Do not engage the self-propelled mechanism on units so

equipped while starting engine.

14. The blade control handle is a safety device. Never attempt to

bypass its operation. Doing so makes the safety device

inoperative and may result in personal injury through contact

with the rotating blade. The blade control handle must operate

easily in both directions and automatically return to the

disengaged position when released.

15. Never operate the mower in wet grass. Always be sure of your

footing. A slip and fall can cause serious personal injury. If you

feel you are losing your footing, release the blade control handle

immediately and the blade will stop rotating within three

seconds.

16. Mow only in daylight or in good artificial light. Walk, never run.

Stop the blade when crossing gravel drives, walks or roads.

17. If the equipment should start to vibrate abnormally, stop the

engine and check immediately for the cause. Vibration is

generally a warning of trouble.

18. Shut the engine off and wait until the blade comes to a complete

stop before removing the grass catcher or unclogging the chute.

The cutting blade continues to rotate for a few seconds after the

engine is shut off. Never place any part of the body in the blade

area until you are sure the blade has stopped rotating.

19. Never operate mower without proper trail shield, discharge

cover, grass catcher, blade control handle or other safety

protective devices in place and working. Never operate mower

with damaged safety devices. Failure to do so, can result in

personal injury.

20. Muffler and engine become hot and can cause a burn. Do not

touch.

21. Only use parts and accessories made for this machine by the

manufacturer. Failure to do so can result in personal injury.

22. If situations occur which are not covered in this manual, use care

and good judgment. Call customer assistance for the name of

your nearest servicing dealer.

SlopeOperation

Slopes are a major factor related to slip and fall accidents which can

result in severe injury. Operation on slopes requires extra caution. If

you feel uneasy on a slope, do not mow it. For your safety, use the

slope gauge included as part of this manual to measure slopes before

operating this unit on a sloped or hilly area. If the slope is greater than

15 degrees, do not mow it.

Do:

1. Mow across the face of slopes; never up and down. Exercise

extreme caution when changing direction on slopes.

2. Watch for holes, ruts, rocks, hidden objects, or bumps which can

cause you to slip or trip. Tall grass can hide obstacles.

3. Always be sure of your footing. A slip and fall can cause serious

personal injury. If you feel you are losing your balance, release

the blade control handle immediately, and the blade will stop

rotating within 3 seconds.

DoNot:

1. Do not mow near drop-offs, ditches or embankments, you could

lose your footing or balance.

2. Do not mow slopes greater than 15 degrees as shown on the

slope gauge.

3. Do not mow on wet grass. Unstable footing could cause slipping.

Children

Tragic accidents can occur if the operator is not alert to the presence

of children. Children are often attracted to the mower and the mowing

activity. They do not understand the dangers. Never assume that

children will remain where you last saw them.

1. Keep children out of the mowing area and under the watchful

care of a responsible adult other than the operator.

2. Be alert and turn mower off if a child enters the area.

3. Before and while moving backwards, look behind and down for

small children.

4. Use extreme care when approaching blind corners, doorways,

shrubs, trees, or other objects that may obscure your vision of a

child who may run into the mower.

5. Keep children away from hot or running engines. They can suffer

burns from a hot muffler.

6. Never allow children under 14 years old to operate a power

mower. Children 14 years old and over should read and

understand the operation instructions and safety rules in this

manual and should be trained and supervised by a parent.

Service

SafeHandlingOfGasoline:

1. To avoid personal injury or property damage use extreme care in

handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself or your clothes which can ignite.

2. Wash your skin and change clothes immediately.

3. Use only an approved gasoline container.

4. Never fill containers inside a vehicle or on a truck or trailer bed

with a plastic liner. Always place containers on the ground away

from your vehicle before filling.

5. Remove gas-powered equipment from the truck or trailer and

refuel it on the ground. If this is not possible, then refuel such

equipment on a trailer with a portable container, rather than from

a gasoline dispenser nozzle.

6. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do not

use a nozzle lock-open device.

7. Extinguish all cigarettes, cigars, pipes and other sources of

ignition.

8. Never fuel machine indoors because flammable vapors will

accumulate in the area.

9. Never remove gas cap or add fuel while the engine is hot or

running. Allow engine to cool at least two minutes before

refueling.

10. Never over fill fuel tank. Fill tank to no more than ½ inch below

bottom of filler neck to provide for fuel expansion.

11. Replace gasoline cap and tighten securely.

12. If gasoline is spilled, wipe it off the engine and equipment. Move

unit to another area. Wait 5 minutes before starting the engine.

13. Never store the machine or fuel container near an open flame,

spark or pilot light as on a water heater, space heater, furnace

,clothes dryer or other gas appliances.

14. To reduce fire hazard, keep mower free of grass, leaves, or other

debris build-up. Clean up oil or fuel spillage and remove any fuel

soaked debris.

15. Allow a mower to cool at least 5 minutes before storing.

GeneralService:

1. Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless and

deadly gas.

2. Before cleaning, repairing, or inspecting, make certain the blade

and all moving parts have stopped. Disconnect the spark plug

wire and ground against the engine to prevent unintended

starting.

3. Check the blade and engine mounting bolts at frequent intervals

for proper tightness. Also, visually inspect blade for damage

(e.g., bent, cracked, worn) Replace blade with the original

equipment manufacture's (O.E.M.) blade only, listed in this

manual. "Use of parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safetyF

4. Mower blades are sharp and can cut. Wrap the blade or wear

gloves, and use extra caution when servicing them.

5. Keep all nuts, bolts, and screws tight to be sure the equipment is

in safe working condition.

6. Never tamper with safety devices. Check their proper operation

regularly.

7. After striking a foreign object, stop the engine, disconnect the

spark plug wire and ground against the engine. Thoroughly

inspect the mower for any damage. Repair the damage before

starting and operating the mower.

8. Never attempt to make a wheel or cutting height adjustment

while the engine is running.

9. Grass catcher components, discharge cover, and trail shield are

subject to wear and damage which could expose moving parts or

allow objects to be thrown. For safety protection, frequently

check components and replace immediately with original

equipment manufacturer's (O.E.M.) parts only, listed in this

manual. "Use of parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safetyF

10. Do not change the engine governor setting or overspeed the

engine. The governor controls the maximum safe operating

speed of the engine.

11. Maintain or replace safety labels, as necessary.

12. Observe proper disposal laws and regulations. Improper

disposal of fluids and materials can harm the environment.

YourResponsibility

Restrict the use of this power machine to persons who read,

understand and follow the warnings and instructions in this

manual and on the machine.

I.IJ

I--

I.IJ

{

i..I

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

A POWER POLE

A CORNER OF A BUILDING

15°

DANGER

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could

__ overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing

and you could slip, resulting in serious injury.

-_ Operate RIDING mowers up and down slopes, never across the face of slopes.

Operate WALK-BEHIND mowers across the face of slopes, never up and down slopes.

SECTION3: SETTINGUP

SparkPlugWire

1. Disconnect spark plug wire from the spark

plug, and ground it against the engine.

2. If engine is equipped with a rubber boot, attach

rubber boot to a bolt on the engine to ground.

See Figure 1.

_olt Plug

Wire

Fig

Spark Plug _=_

ireX II

Spark Plug

ire 1

ShippingBlock

The chute deflector on your mower may be held in

an upright position by a block for shipping

purposes only. This shipping block must be

removed and discarded before the mower is put

into operation. See Figure 2.

1. To remove the shipping block, pull the spring-

loaded chute toward the engine. Remove the

block and carefully lower the chute into

operating position, keeping fingers out of the

way.

Upper&LowerHandles

1. Pull up and back on the upper handle to raise

the handle into the operating position. Make

certain the lower handle is seated securely into

the handle mounting brackets.

2. Tighten wing nuts A on each side of the

handle. See Figure 3.

NOTE: Your mower is shipped with the handle in

the higher position. If you wish to lower the height

of the handle refer to the Adjustment Section.

3. Tighten wing nuts C and D at the end of the

lower handle to secure the handle to the

handle mounting brackets.

4. Fasten the cable to the left lower handle with

the cable tie. Pull the cable tie tight and trim off

the excess. See Figure 4.

Shipping

Block

Figure 2

Wing Nut C

_ \ Wing NutB

Nut D

Figure 3

StarterRope

1. The starter rope is attached to the engine. Additional rope

may be wound around the starter handle. If so, unwind the

rope from the handle.

2. With the spark plug wire disconnected and grounded,

depress the blade control handle and pull the rope out of

the engine.

3. Place the rope guide around the starter handle, so the

opening in the rope guide is toward the front of the mower.

Insert the rope guide into the right side of the handle, and

secure with hex Iocknut. See Figure 4.

NOTE: If the starter rope becomes disconnected from rope

guide on handle, disconnect and ground the spark plug

wire. Depress the blade control handle and pull the starter

rope out from engine slowly. Slip the starter rope into the rope

guide bolt on handle.

MulchingBaffle

If your mower is equipped with a mulching baffle,

install it on the right side of the deck. Follow the

sequence indicated here.

1. Lift up and hold the side-discharge chute

deflector.

2. Insert bottom lip of the mulching baffle inside

the chute opening (marked 1 in Figure 5).

3. Snap hooks of the mulching baffle over the

hinge pin of the chute deflector (marked 2 in

Figure 5). The hooks must snap into place on

the hinge pin, locking the mulching baffle firmly

onto the mower. Release the chute deflector.

NOTE: For proper assembly, install bottom lip

inside chute opening before placing hooks over

the hinge pin.

IMPORTANT: This unit is shipped without gasoline

or oil in the engine. Fill up gasoline and oil as

instructed in the accompanying engine manual

before operating your mower.

Chute

Mulching

Baffle

Starter .

Handle

Rope

Guide

Starter_

Rope

Hex

Lock

Figure 4

Lip ofMulching Baffle

(insert inside chute opening)

Figure 5

Cable

Tie

Opening

SECTION4: OPERATINGYOURLAWNMOWER

Knowyourlawnmower

BladeControlHandle

The blade control handle is located on the upper

handle of the mower. See Figure 6. The blade

control handle must be depressed in order to

operate the unit. Release the blade control handle

to stop the engine and blade.

,i_ WARNING: This blade control

mechanism is a safety device. Never

attempt to bypass its operation.

CuttingHeightAdjustmentLevers

One adjustment lever is located on each wheel

and is used to adjust the cutting height. All four

levers have to be at the same relative position to

ensure uniform cut.

RecoilStarter

The recoil starter is attached to the right upper

handle. Stand behind the unit and pull the recoil

starter rope to start the unit.

MulchingBaffle

The mulching baffle is used to recirculate grass

clippings back to the lawn. Attach it as instructed

on page 7 of this manual.

Blade Control Handle

Handle

Recoil Starter

Hei

Levers

Figure 6

Rope

Height

Adjustment

Levers

BeforeStarting

• Service the engine with gasoline and oil as instructed in the separate engine manual. Read instructions

carefully.

,_ WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vaporsare explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes,

cigars, pipes and other sources of ignition.

• Attach spark plug wire to spark plug. If unit is equipped with a rubber boot over the end of the spark plug wire,

make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over

the metal tip on the spark plug.

,_ WARNING: The operation of any lawn mower can result in foreign objects being thrown into the eyes,which can damage your eyes severely. Always wear safety glasses while operating the mower, or while

performing any adjustments or repairs on it.

StartingEngine

,_ WARNING: Be sure no one other than the operator is standing near the lawn mower while starting

engine or operating mower. Never run engine indoors or in enclosed, poorly ventilated areas. Engine

exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing

away from any moving parts on engine and lawn mower.

• If your unit is equipped with a primer, prime

engine as instructed in the separate engine

manual packed with your unit.

• Standing behind the unit, depress the blade

control handle and hold it against the upper

handle as shown in Figure 7.

• Grasp the recoil starter handle as shown and

pull slowly until resistance is felt, then pull

rapidly to start engine and avoid kickback.

Return it slowly to the rope guide bolt.

NOTE: The blade control handle must be

depressed in order to operate the unit. Release

the blade control handle to stop the engine and

blade.

Starter

Handle

,/'1

Figure 7

,i_ WARNING: THIS CONTROL MECHANISM IS A SAFETY DEVICE. NEVER ATTEMPT TO BYPASS

ITS OPERATION.

StoppingEngine

1. Release blade control handle to stop the engine and the blade.

2. Disconnect spark plug wire from spark plug and ground against the engine.

UsingYourLawnMower

IMPORTANT:Be sure the lawn is clear of stones, sticks, wire, or other objects which could damage the lawn mower

or the engine. Such objects could be accidently thrown by the mower in any direction and cause serious personal

injury to the operator and others.

,_ WARNING: If you strike a foreign object, stop the engine. Remove wire from the spark plug, thoroughlyinspect the mower for any damage, and repair the damage before restarting and operating the mower.

Extensive vibration of the mower during operation is an indication of damage. The unit should be promptly

inspected and repaired.

OperatingTips

• For best results, do not cut wet grass.

• New grass, thick grass, or wet grass may require a narrower cut.

• For a healthier lawn, never cut off more than one-third of the total length of the grass.

• Your lawn should be cut in the fall as long as there is growth.

• For effective mulching, do not cut wet grass.

• Adjust ground speed according to the condition of the lawn.

• If the grass has been allowed to grow in excess of 4 inches, mulching is not recommended.

Mow using the side discharge to reduce the grass height to 3-1/4 inches or less before

mulching.

SECTION5: MAKINGADJUSTMENTS

_ ARNING: Always stop engine, disconnect spark plug, and ground against engine before performing

adjustments.

CuttingHeight

Each wheel has a height adjustment lever to

change the cutting height of the mower.

1. To change the height of cut, squeeze adjuster

lever toward the wheel, moving up or down to

selected height.

NOTE: All wheels must be in the same height of

cut.

Height Adjustment

HandleHeight

To lower the handle height, proceed as follows:

1. Remove the starter rope from the rope guide.

2. Remove the hardware securing the lower

handle to handle brackets and remove the

lower handle being careful not to bend or kink

the cables.

3. Reassemble placing the top holes in the

handle over the weld pins in the handle

mounting brackets.

4. Secure with hardware previously removed.

5. Reassemble the upper handle to the lower

handle.

6. Attach the starter rope and rope guide as

instructed in the "Set-up" instructions.

7. Remember to attach the spark plug wire after

completing the adjustments and before

operating your mower.

Wing

Nuts

Handle

Mounting

Brackets

Figure 8

Lower

Handle

Figure 9

SECTION6: MAINTAININGYOURLAWNMOWER

GeneralRecommendations

• Always observe safety rules when performing any maintenance.

• The warranty on this lawn mower does not cover items that have been subjected to operator abuse or

negligence. To receive full value from the warranty, operator must maintain the lawn mower as instructed here.

• Changing of engine-governed speed will void engine warranty.

• All adjustments should be checked at least once each season.

• Periodically check all fasteners and make sure these are tight.

,_ WARNING: Always stop engine, disconnect spark plug, and ground against engine before cleaning,lubricating or doing any kind of maintenance on your machine.

Lubrication

BladeControlHandle

• Lubricate the pivot points on the blade control

handle at least once a season with light oil.

The blade control must operate freely in both

directions. See Figure 10.

Wheels

• If your mower is equipped with ball bearing

wheels, lubricate at least once a season with

a light oil, all other types require no

lubrication. However, if the wheels are

removed for any reason, lubricate the surface

of the axle bolt and the inner surface of the

wheel with light automotive oil.

ChuteDeflector

• Lubricate the torsion spring and pivot point

periodically with light oil to 3revent rust. See

Figure 10.

Engine

Follow the accompanying engine manual for

lubrication schedule and instruction.

Figure 10

Lubricate these

points

Lubricate these

points

CleaningMower

• The underside of the mower deck should be cleaned after each use to prevent a buildup of grass clippings,

leaves, dirt or other matter. Follow the steps below for this job.

NOTE: We do not recommend the use of pressure washers or garden hose to clean your unit. These may cause

damage to electric components, spindles, pulleys, bearings, or the engine. The use of water will result in shortened

life and reduce serviceability.

1. Disconnect spark plug wire. Drain gasoline from the lawn mower, or place a piece of plastic under the gas cap.

2. Tip the mower so that it rests on the housing. Keep the side with the air cleaner facing up. Hold the mower firmly.

,_ WARNING: Never tip the mower more than 90 degrees in any directions and do not leave the mowertipped for any length of time. Oil can drain into the upper part of the engine causing a starting problem.

3. Scrape and clean the underside of the deck with a suitable tool. Do not spray with water.

4. Put the mower back on its wheels on the ground. If you had put plastic under the gas cap earlier, make sure to

remove it now.

BladeCareandReplacement

,_ WARNING: When removing the cutting blade for sharpening or replacement, protect your hands with a

pair of heavy gloves or use a heavy rag to hold the blade.

Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when necessary.

Follow the steps below for blade service:

• Disconnect spark plug wire from spark plug.

• Tip mower as specified in separate engine manual. If it does not specify turn mower on its side making sure that

the air filter and the carburetor are up.

• Remove the bolt and the blade bell support which

hold the blade and the blade adapter to the engine

crankshaft. See Figure 11.

• Remove blade and adapter from the crankshaft.

• The blade may be resharpened by removing it and

either grinding or filing the cutting edge keeping as

close to the original bevel as possible. Do not Crankshaft

attempt to sharpen the blade while it is still on the Blade

mower. Adapter

• It is extremely important that each cutting edge

receives an equal amount of grinding to prevent

an unbalanced blade.

NOTE: Improper blade balance will result in excessive

vibration causing eventual damage to the engine and Hex. Bolt

mower. Be sure to carefully balance blade after

sharpening. Possible damage resulting from blade

unbalance condition is not the responsibility of the manufacturer.

Blade Bell

Support

Figure 11

NOTE: Always remove blade from the adapter for testing balance.

• The blade can be tested for balance by balancing it on a round shaft screwdriver. Remove metal from the heavy

side until it balances evenly.

• Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner

surface of the blade adapter with light oil.

• Install the blade adapter on the crankshaft with the "star" away from the engine. See Figure 11. Place the blade

with the side marked "bottom" (or with part number) facing away from the adapter. Align the blade bell support

over the blade with the tabs in the holes of the blade and insert the hex bolt.

• Tighten the hex bolt to the torque listed below:

BladeMountingTorque

Center Bolt 450 in. lb. min., 600 in.lb, max.

To insure safe operation of your unit, ALL nuts and bolts must be checked periodically for correct tightness.

NOTE: Cutting grass in sandy soil condition causes abrasive wear to the blade.

Off-SeasonStorage

The following steps should be taken to prepare your lawn mower for storage.

1. Clean and lubricate mower thoroughly as described in the lubrication instructions.

IMPORTANT:We do not recommend the use of a pressure washer or garden hose to clean your unit.

2. Refer to engine manual for correct engine storage instructions.

3. Coat mower's cutting blade with chassis grease to prevent rusting.

4. Store mower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in a poorly ventilated or metal storage shed, care should be

taken to rust-proof the equipment. Using a light oil or silicone, coat the equipment, especially cables and all moving

parts of your lawn mower before storage

SECTION7: TROUBLESHOOTING

Engine fails to start

Engine runs erratic

Engine overheats

Occasional skip (hesitates

at high speed

Idles poorly

Excessive vibration

Mower will not mulch grass

Uneven cut

1. Blade control handle disengaged.

2. Spark plug wire disconnected.

3. Fuel tank empty or stale fuel.

4. Blocked fuel line.

5. Faulty spark plug.

6. Engine flooded

1. Spark plug wire loose.

2. Blocked fuel line or stale fuel.

3. Vent in gas plugged.

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Carburetor out of adjustment.

1. Engine oil level low.

2. Air flow restricted.

3. Carburetor not adjusted properly.

1. Engage blade control handle.

2. Connect wire to spark plug.

3. Fill tank with clean, fresh gasoline.

4. Clean fuel line.

5. Clean, adjust gap, or replace.

6. Wait a few minutes to restart, but do not

prime.

1. Connect and tighten spark plug wire.

2. Clean fuel line; fill tank with clean, fresh

gasoline

3. Clear vent.

4. Drain fuel tank. Refill with fresh fuel.

5. Clean air cleaner.

6. Adjust carburetor.

1. Fill crankcase with proper oil.

2. Remove blower housing and clean.

3. Adjust carburetor.

1. Spark plug gap too close.

Spark plug fouled, faulty or gap too

wide.

Carburetor improperly adjusted.

Dirty air cleaner.

Cutting blade loose or unbalanced.

Bent cutting blade.

Wet grass.

Excessively high grass.

3. Dull blade.

1. Wheels not positioned correctly.

2. Dull blade.

1. Adjust gap to .030".

1. Reset gap to .030" or replace spark

plug.

2. Adjust carburetor.

3. Service air cleaner.

1. Tighten blade and adapter. Balance

blade.

2. Replace blade.

1. Do not mow when grass is wet; wait

until later to cut.

2. Mow once at a high cutting height, then

mow again at desired height or make a

narrower cutting path.

3. Sharpen or replace blade.

1. Place all four wheels in same height

position.

2. Sharpen or replace blade.

NOTE: For repairs beyond the minor adjustments listed above, contact an authorized service dealer.

SECTION8: PARTSLISTFORSERIES080/LISTEDEPII_CESDETACHI_ESSI_RIES080

20 11

REF

NO.

N° DE

REF

PART

NO.

N°DE

PII_CE

747-1161A

749-1092A

720-0279

710-1205

710-1174

720-0284

736-0451

749-04037

725-0157

710-0599

17098

731-04019

682-3065

682-3064

687-02045

687-02048

710-0654A

741-0751

687-02051

710-0216

687-02094

738-1173

736-0741

734-1987

736-0270

738-1172

734-1988

748-0376C

742-0642A

742-0742A

736-0524A

710-1044

747-0710

732-1014

17032A

731-1035B

731-1034B

746-0957

746-1130

746-0946

631-04045

712-0431

751168114

DESCRIPTION

Blade Control Handle

Upper Handle

Knob - ERS Guide 1/4-20

Rope Guide Bolt

Carriage Bolt 5/16-18 x 2.0

Handle Knob Assembly

Saddle Wash..320 ID x .937 OD

Lower Handle

Cable Tie

Hex Wash S-Tapp Scr 1/4-20 x .50

Hinge Clip

Trail Shield

Handle Bracket Assembly LH

Hanldle Bracket Assembly RH

Deck Assembly 22" (with logo)

Deck Assembly 22" (without logo)

Hex Wash HD Tap Scr 3/8-16 x .88

Height Adjuster Bearing

Lever Assembly (includes Ref. #18)

Hex Cap Screw 3/8-16 x .75

Pivot Bar

Shoulder Screw

Cupped Washer .401 JDx .870 OD

Wheel Ass'y 8 x 1.8 Spoke Bar Grey

Cup. Wash..265 JDx .75 OD x .062

Shoulder Screw 3/8-16

Wheel Assembly Complete 7 x 1.8

Blade Adapter

Blade 22"

Mulching Blade 22"

Blade Bell Support

Hex Screw 3/8-24 x 1.5" Lg. (Gr. 8)

Hinge Pin

Torsion Spring

Chute Hinge

Chute Deflector

Side Dis. Chute Ass'y (incl. #34-37)

Control Cable 37.25" Lg.

Blade Control Cable 40"

Control Cable 48.25" Lg.

Mulch Plug (if equipped)

Flanged Lock Nut

Shroud

DESCRIPTION

Poignee de commande de la lame

Guidon superieur

Bouton - 1/4-20

Boulon de guidage de cordon

Boulon ordinaire 5/16-18 x 2,0

Bouton

Rondelle selle 0,320 DI x 0,937 DE

Guidon inferieur

Attache-cable

Vis autotaraudeuse a rondelle hex. de 1/4-20 x 0,5

Attache

Abattant de protection arriere

Support de guidon CG

Support de guidon CD

Plateau de coupe de 22 po (avec logo)

Plateau de coupe de 22 po (sans logo)

Vis autotaraudee 3/8-16 x 0,88

Roulement

Levier (inclus le no. de ref. 18)

Visa chapeau a six pans de 3/8-16 x 0,75

Barre de pivot

Visa epaulement

Rondelle creuse 0,401 DI x 0,870 DE

Ensemble de roue 8 x 1,80 gris

Rondelle creuse 0,265 DI x 0,75 DE x 0,062

Visa epaulement 3/8-16

Ensemble de roue complet 7 x 1,80

Adaptateur de la lame

Lame 22 po

Lame dechiqueteuse 22 po

Support de lame

Visa tete hex. 3/8-24 x 1,50 po de Ig (Qual. 8)

Axe fixe

Ressort de torsion

Charniere de deflecteur

Deflecteur lateral

Deflecteur lateral complet (incl. No.34-37)

Cable de la commande 37,25 po de Ig.

Cable de commande de la lame de 40 po

Cable de la commande 48,25 po de Ig.

Plaque de dechiquetage (si equipe)

Ecrou de blocage

Capot

11A-080

10.15.04

MANUFACTURER'S LIMITED WARRANTY FOR:

Thelimited warranty setforth below is given by MTDLLCwith respectto newmerchandisepurchased and

usedin the United Statesand/or its territories and possessions,and byMTD Products Limited with respect

to newmerchandise purchasedand used in Canadaand/or itsterritories andpossessions (either entity

respectively,"MTD").

MTDwarrants this product (excludingits normal wearparts asdescribed below)against defectsin materialandworkmanship for a periodof two

(2) yearscommencing onthe dateof original purchaseand will, at its option, repairor replace,free ofcharge,any partfound to be defectivein

materialsor workmanship. This limitedwarranty shall onlyapply if this product hasbeenoperatedand maintainedinaccordancewith the

Operator's Manualfurnished with the product, and hasnotbeensubjectto misuse, abuse,commercial use,neglect,accident, improper

maintenance,alteration, vandalism,theft,fire, water, or damagebecauseof other perilor naturaldisaster. Damageresulting from the installation

or useofany part, accessoryor attachmentnot approved by MTDfor usewith the product(s) coveredbythis manualwill void your warranty as

to any resulting damage.

Normal wearpartsarewarrantedto befreefrom defects in materialandworkmanship for aperiod of thirty (30) daysfrom the dateof purchase.

Normal wearparts include,but are not limited to items such as:batteries, belts, blades,bladeadapters,grass bags,rider deckwheels, seats,

snowthrower skid shoes,friction wheels, shaveplates,augerspiral rubber andtires.

HOWTOOBTAINSERVICE:Warranty serviceisavailable,WITHPROOFOFPURCHASE,through your localauthorized servicedealer.Tolocate

the dealerin your area;

Inthe U.S.A.:

Checkyour Yellow Pages,or contact MTDLLCat P.O.Box361131, Cleveland,Ohio44136-0019, or call 1-800-800-7310 or 1-330-220-4683 or

log onto ourWeb siteat www.mtdproducts.com.

In Canada:

ContactMTD Products Limited, Kitchener,ONN2G4J1, or call 1-800-668-1238 or log onto our Website atwww.mtdcanada.com.

This limited warranty does not provide coveragein the following cases:

a. Theengine or component partsthereof. Theseitems maycarry aseparatemanufacturer's warranty. Referto applicable

manufacturer's warrantyfor terms and conditions.

b. Logsplitter pumps,valves,andcylinders haveaseparateone-yearwarranty.

c. Routinemaintenanceitems such aslubricants, filters, bladesharpening,tune-ups, brakeadjustments, clutch adjustments, deck

adjustments, andnormal deteriorationof the exterior finish dueto useor exposure.

d. Servicecompleted bysomeoneother than anauthorized servicedealer.

e. MTDdoes not extendanywarranty for products soldor exported outside ofthe UnitedStatesand/or Canada,andtheir respective

possessionsandterritories, exceptthose soldthrough MTD'sauthorized channels of exportdistribution.

f. Replacementpartsthatare not genuineMTD parts.

g. Transportation chargesand service calls.

h. If Productsareusedcommercially. (MTDmay separatelyoffer Limited CommercialWarranties oncertain selectproducts. Askyour

dealer orretailer for details or contact MTDServicefor more information.)

No implied warranty,including any implied warrantyof merchantabilityof fitness for aparticularpurpose,appliesafter the applicable

periodof expresswrittenwarranty aboveastothe partsasidentified. No other expresswarranty,whetherwritten or oral, exceptas

mentionedabove, givenbyanypersonor entity, includinga dealeror retailer, with respectto anyproduct,shallbindIVITD.Duringthe

periodof thewarranty, the exclusiveremedyisrepair orreplacementof the productassetforth above.

Theprovisionsassetforth inthiswarrantyprovidethesole andexclusiveremedyarisingfrom the sale. IVITDshall notheliablefor

incidentalor consequentiallossor damage including,withoutlimitation, expensesincurredfor substituteor replacementlawncare

servicesor for rentalexpensesto temporarily replacea warrantedproduct.

Somejurisdictions do not allow theexclusion or limitation of incidental or consequentialdamages,or limitations on how long an implied

warranty lasts, sothe aboveexclusions or limitations may not apply to you.

In no eventshall recoveryof any kind begreaterthan the amount ofthe purchaseprice of the product sold.Alteration ofsafetyfeatures of the

product shallvoidthis warranty. You assumethe risk and liability for loss, damage,or injuryto you and your property and/orto others andtheir

property arising out ofthe misuse or inability to usethe product.

This limited warranty shall not extendto anyone other thanthe original purchaseror to the personfor whom it waspurchasedas agift.

NOWLOCALLAWSRELATETOTHIS WARRANTY:This limitedwarranty givesyou specific legalrights, and you mayalso haveother rightsthat

vary indifferent jurisdictions.

IMPORTANT:Ownermust presentOriginal Proof of Purchaseto obtainwarranty coverage.

IVITDLLC,P.O. BOX361131 CLEVELAND,OHIO44136-0019; Phone:1-800-800-7310, 1-330-220-4683

IVITDProductsLtd., P.O. BOX1386, KITCHENER,ONN2G4J1; Phone:1-800-668-1238

Notice d'utilisation

Tondeuse rotative

de 22 po

Series 080

IMPORTANT:Lisez attentivement les r_gles de s6curit6 et les instructions avant de mettre en marche la machine.

Avertissement: Cet appareil est equipe d'un moteur a combustion interne. Pour cette raison, il ne doit pas 6tre utilise sur un terrain forestier

non debroussaille ou sur tout autre terrain recouvert de broussailles ou d'herbes s'il n'est pas equipe d'un pare-etincelles conforme & toutes

les lois appticables a I'echelle locale ou de I'etat (le cas echeant). Tout pare-etincelles doit _tre maintenu en parfait etat de fonctionnement

par I'utilisateur. L'#tat de Californie I'exige en vertu du Code sur les ressources publiques 4442. D'autres lois similaires peuvent 6tre en

vigueur dans certains autres etats. Les lois federales sont applicables sur les terres federales. Vous pouvez vous procurer un pare-etincelles

&installer sur le silencieux aupres de la station technique agreee la plus proche ou adressez-vous au service apr_s-vente, P. O. 361131,

Cleveland, Ohio 44136-0019.

Pourclientsdes I_tats-Unis:MTD LLC,P.O.BOX361131CLEVELAND,OHIO44136-0019

Pourclientsdu Canada:MTD ProductsLtd., P.O. BOX1386, KITCHENER,ONTARION2G4J1

IMPRIM# AUX #TATS-UNIS.

FORM NO. 769-01440

(10/2004)

TABLEDESMATII RES

Contenu

Service apres-vente

Importantes consignes de securite

Inclinometre

Installation

Utilisation

Page

Contenu Page

Reglages 11

Entretien 11

Depannage 14

Garantie 15

Liste de pieces detachees (voir la page

14 de la version anglaise

POURTROUVERLENUMI RODEMODI LE

Cette notice d'utilisation est une piece importante de votre nouveau equipement. Elle vous fournit les

renseignements necessaires & I'assemblage, & la preparation et a I'entretien de votre machine. Veuillez donc la

lire attentivement et vous assurer de bien comprendre toutes les instructions.

Avant de proc_der _ rassemblage de votre nouveau _quipment, Iocaliser la plaque signaletique

sur la machine et recopier le num@o de modele et la numero de s@ie aux endroits prevus ci-dessous.

La plaque signaletique apparait comme ci-dessous. Pour Iocaliser la plaque signaletique, placez-vous

derriere la machine & la poste de conduite et regardez & I'arriere de la machine. Ces renseignements

s'averont tres importants si vous utilisez le site web du fabricant et/ou vous devez vous addresser au

service apres-vente ou concessionaire local.

Model Number Serial Number

Num#ro de module Num#ro de s#rier

XXXXXXXXXXX XXXXXXXXXXX

MTD LLC

CLEVELAND, OH 44136

MTD PRODUCTS LIMITED

KITCHENER, ON N2G 4Ji

USA-www.mtdproducts.com 1-800-800-7310

CAN-www.mtdcanada.com 1-800-668-1238

Recopiez ici le num6ro de module:

Recopiez ici le num6ro de s_rie:

INFORMATIONDEMOTEUR

Le fabricant du moteur est responsable pour tout questions relic au moteur en ce qui concerne la perfomance,

puissance, caract@istique, garantie et service. Pour plus de renseignements, consultez votre notice d'utilisation du

moteur empaquete separement avec votre equipment.

SERVICEAPRI S-VENTE

Veuillezretourner la machineaud6taillantqui vousI'a vendue,sans vous adresserd'abordauservice apr_s-vente.

Si I'assemblage de cette machine vous pose des problemes ou pour toute question concernant les

commandes, le fonctionnement ou I'entretien de la machine, appelez le service apres-vente au:

Pour clients des F=tats-Unis: 1-330-220-4MTD (4683) or 1-800-800-7310

Pour clients du Canada: 1-800-668-1238

Preparez vos numeros de modele et de serie avant de telephoner. Bien que les deux numeros soient importants,

vous ne devrez enregistrer que le numero de s@ie avant de pouvoir poursuivre votre consultation.

POURFAIREHONORERLAGARANTIE

Presentez UNE PREUVE D'ACHAT & la station technique agreee de votre Iocalit& Pour Iocaliser une station

technique agreee ou un concessionnaire dans votre region :

Aux letats-Unis: Consultez les Pages Jaunes ou adressez-vous a MTD LLC, P.O. Box 361131, Cleveland, Ohio

44136-0019 ou appelez le 1-800-800-7310 ou le 1-330-220-4683. Vous pouvez aussi visiter notre site web au

www.mtdproducts.com

Au Canada: Adressez-vous a MTD Products Limited, Kitchener, Ontario, N2G 4J1 ou appelez le 1-800-668-1238

ou visitez notre site web au www.mtdcanada.com

CHAPITRE1: IMPORTANTESCONSIGNESDESI CURITI

AVERTISSEMENT: Ce symbole attire votre attention sur des consignes de s6curit6 importantes qui,

si elles ne sont pas respect6es, peuvent mettre en danger non seulement votre personne et vos biens,

mais aussi ceux d'autrui. Pri6re de lire toutes les instructions figurant dans cette notice d'utilisation avant

d'essayer de vous servir de cette machine. Le non-respect de ces instructions peut entrafner des

blessures corporelles. Respectez I'avertissement qui accompagne ce symbole.

AVERTISSEMENT: Les gaz d'6chappement de ce produit contiennent des produits chimiques

reconnus darts I'€:tat de Californie comme causant le cancer, des anomalies cong6nitales ou d'autres

probl6mes li6s a la reproduction.

DANGER: Cette machine doit _tre utilis6e conform6ment aux consignes de s6curit6 qui figurent dans la

notice d'utilisation. Comme avec tout appareil motoris6, une n6gligence ou une erreur de la part de

I'utilisateur peut entraTner des blessures graves. Cette machine peut amputer mains et pieds et projeter

des d6bris. Par cons6quent, le non-respect de ces consignes peut causer des blessures corporelles

graves et m_me mortelles.

Utilisationeng6n6ral

1. Veuillez life attentivement la notice d'utilisation avant d'essayer

d'assembler la machine. Assurez-vous de lire et de bien

comprendre toutes les instructions qui figurent sur la machine et

darts la notice d'utilisation avant de la mettre en marche.

Famitiarisez-vous avec les commandes et les conseils

d'utilisation de la machine avant de vous en servir. Conservez

cette notice d'utilisation a un endroit sQr pour toute consultation

ulterieure et pour commander des pieces de rechange.

2. Cette machine motorisee est un outil de precision, pas un jouet.

Soyez par consequent toujours tres prudent. Le seul r61ede

cette machine est de tondre le gazon. Ne I'utilisez jamais darts

un autre but.

3. Ne permettez jamais &des enfants de moins de 14 ans de se

servir de la machine. Des adolescents plus &ges doivent life la

notice d'utilisation, bien comprendre le fonctionnement de la

machine et respecter les consignes de securite. IIs doivent

apprendre & utiliser la machine et s'en servir sous la surveillance

etroite d'un adulte. Seules des personnes mQres ayant pris

connaissance des consignes de securite doivent 6tre autorisees

utiliser cette machine.

4. Examiner soigneusement la zone de travail. Ramassez tousles

pierres, b&tons, fil metalliques os, jouets et autre objets qui

pourraient vous trebuchez ou qui risque d'6tre ramasses et

projetes par la lame. Les objets projetes par la machine peuvent

causer des blessures graves. Prevoyez de travailler en evitant

de projeter I'herbe vers des rues, des trottoirs, des spectateurs,

etc. Evitez d'ejecter I'herbe en direction d'un mur ou d'un

obstacle. De cette fa£on, les debris eventuels ne risque pas de

ricocher et de blesser quelqu'un.

5. Pour eviter tout risque de contact avec la lame ou de blessure

par un projectile, eloignez les enfants, passants et autres a au

moins 75 pieds de la tondeuse pendant qu'elle fonctionne.

Arr_tez la machine si quelqu'un s'approche.

6. Portez toujours des lunettes de securite en utilisant la machine

ou en effectuant un reglage ou une reparation. Un objet peut en

effet 6tre projete, ricocher et vous blesser aux yeux.

7. Portez des chaussures robustes & semetle epaisse et des

v6tement bien ajustes.Une chemise et un pantalon qui protegent

les bras et les jambes et des chaussures & bout d'acier sont

recommandes. N'utilisez jamais la tondeuse si vous _tes pieds

nus ou si vous portez des sandales ou des tennis.

8. Ne placez jamais vos mains ou vos pieds pros d'une piece en

mouvement ou sous le plateau de coupe. La lame peut amputer

mains et pieds.

9. L'absence du clapet de la goulotte d'ejection ou un clapet

endommage peut causer des blessures en cas de contact avec

la lame ou projeter des objets.

10. De nombreuses blessures se produisent Iorsque latondeuse

passe sur le pied a la suite d'une chute. Ne retenez pas la

tondeuse si vous tombez. L&chez immediatement leguidon.

11. Ne tirez jamais la tondeuse vers vous en marchant. S'il faut faire

reculer la tondeuse pres d'un mur d'un autre obstacle, regardez

d'abord par terre et derriere vous, puis procedez comme suit:

a. Eloignez-vous de la tondeuse & bout de bras.

b. Assurezvotre stabilite.

c. Reculez la tondeuse lentement et d'une demi-longeur

de bras seulement.

d. Repetez selon les besoin.

12. N'utilisez jamais la tondeuse en etat d'ebriete ou si vous prenez

des medicaments ralentissant les reactions.

13. Degagez le dispositif d'auto-propulsion ou I'embrayage

d'entrafnement, le cas echeant, avant de faire demarrer le

moteur.

14. La poignee de commande de la lame est un dispositif de

securite. Ne tenez jamais de contourner son r61e. Ceci emp6che

le dispositif de securite de fonctionner correctement et peut

causer des blessures en cas de contact avec la lame. La

poignee de commande de la lame dolt bouger facilement dans

les deux sens et revenir automatiquement a la position non

eclenchee quand on la I_che.

15. N'utilisezjamais la tondeuse si le gazon est mouille. Soyez

toujours bien en equilibre. Faites attention de ne pas glisser et

de ne pas tomber pour eviter des blessures graves. Si vous

estimez que vous perdez votre equilibre, I_cher la poignee de

commande de la lame immediatement et la lame arr6tera de

tourner darts trois secondes.

16. Utilisez la tondeuse seulement darts la lumiere du jour ou darts

la bonne lumiere artificielle. Marchez, ne courrez pas. Arr6tez la

lame avant de traverser des allees, trottoirs ou chemins

recouverts de gravier.

17. Si la machine commence &vibrer d'une maniere anormale,

arr6ter le moteur et cherchez-en immediatement la cause. En

general, toute vibration indique un probleme.

18. Arr_tez le moteur et attendez que la ou la lame se soit

immobilisee avant de detacher le sac & herbe ou de deboucher

la goulotte. La lame continue a toumer pendant quelques

secondes apres que le moteur s'est eteint. Ne placezjamais

aucune partie du corps clans le secteur de lame avant que vous

ne soyez sQrs que la lame a arr_te de tourner.

19. N'utilisez jamais la tondeuse sans avoir I'abattant de protection

arri_re, la goulotte d'ejection, un sac & herbe, la poignee de

commande de la lame ou d'autres dispositifs de securite

appropriee, en place et qui fonctionnent correctement. N'utilisez

jamais la tondeuse avec des dispositifs de securite

endommages.Lenon-respectdecesconsignespeuventcauser

desblessuresgraves.

20.Lesilencieuxetlemoteurdeviennenttreschaudsetpeuvent

causerdesbrQlures.Nelestouchezpas.

21.N'utilisezquedesaccessoiresrecommandesparlefabricantde

lamachine.Lenon-respectdececonsignepeutcauserdes

blessuresgraves.

22.Encasdesituationsquinesontpasmentionneesdanscette

notice,soyezprudentetfaitespreuvedebonsens.Contactez

votredepartementdeservice&laclientelespourlenomdebotre

concessionairelocal.

Utilisationsurunepente

Les accidents provoques par tomber et de glisser, qui se produisent

souvent sur des pentes, peuvent causer des blessures graves.

Travailler sur un terrain en pente demande des precautions

supplementaires. Si vous ne sentez pas a I'aise sur la pente, n'y

travaillez pas. Par mesure de securite utilisez I'inclinometre fourni

dans la notice d'utilisation pour mesurer la pente du terrain avant de

commencer a travailler. Si selon I'inclinometre, la pente est

superieure a 15°, n'utilisez pas la tondeuse pour eviter toute blessure

grave.

A FAIRE:

1. Travailler parallelement a la pente, jamais perpendiculairement,

Faites tres attention en changeant de direction sur une pente.

2. Faites attention aux trous et ornieres. La machine peut se

retourner sur un terrain accident& Des herbes hautes peuvent

cacher des obstacles.

3. Verifier toujours votre equilibre. Vous risquez de glisser et de

tomber et de vous blesser grievement. Si vous sentez que vous

allez perdre votre equilibre, I&chez immediatement le guidon, et

la lame arr6tera de tourner dans trois secondes.

P,NEPASFAIRE:

1. Ne tondez pas pres d'une falaise ou d'un talus. Le conducteur

peut facilement perdre I'equilibre.

2. Ne tondez pas sur une pente superieure a 15° selon

I'inclinom_tre.

3. Ne tondez pas de I'herbe mouillee. La traction reduite peut

provoquer un derapage.

Enfant

Un accident grave risque de se produire si le conducteur n'est pas

toujours vigilant en presence d'enfants. Les enfants sont souvent

attires par la machine et la tonte de I'herbe. IIs ne comprennent pas

les dangers. Ne supposez jamais qu'ils vont rester la oQ vous les avez

VUS.

1. ¢loignez les enfants de la zone de travail et placez-les sous la

surveillance d'un adulte autre que le conducteur de la machine.

2. Restez vigilant et arr6tez la machine si des enfants s'approchent

de la zone de travail.

3. Regardez toujours derriere vous et par terre avant de reculer et

en reculant.

4. Faites tres attention en approchant d'angles morts, de buissons,

d'autres objets qui peuvent g_ner votre visibilit&

5. Tenir des enfants loin de moteurs chauds ou tournants. IIs

peuvent subir des brQlures graves d'un silencieux chaud.

6. Ne permettez jamais &des enfants de moins de 14 ans d'utiliser

la tondeuse. Des adolescents _ges de 14 ans ou plus doivent

lire la notice d'utilisation, bien comprendre le fonctionnement de

la machine et respecter les consignes de securit& tls doivent

apprendre & utiliser la machine et s'en servir sous la surveillance

etroite d'un adulte.

ENTRETIEN

ManipulationdeI'essence:

1. Pour eviter toute blessure ou deg&t materiel, faites tres attention

en manipulant de I'essence. IIs'agit d'un produit extr_mement

inflammable et les vapeurs risquent d'exploser. Vous pouvez

6tre grievement blesse si des eclaboussures sur votre peau ou

sur vos v_tements s'enflammaient.

2. Rincez votre peau et changez immediatement de v6tements.

3. Remissez le carburant dans des bidons homologues seulement.

4. Ne faites jamais le plein dans un vehicule, ni & I'arriere d'une

camionette dont le plancher est recouvert d'un rev6tement en

plastique. Placez toujours les bidons par terre et loin de votre

vehicule avant de les remplir.

5. Dans le mesure du possible, dechargez I'equipement motorise

de la remorque et faites le plein par terre. Si cela n'est pas

possible, faites le plein avec un bidon plut6t que directement de

la pompe a essence.

6. Maintenez le gicleur en contact avec le bord du reservoir

d'essence ou avec I'ouverture du bidon jusqu'& ce que le plein

soit termin& N'utilisez pas un gicleur equipe d'un dispositif de

blocage en position ouverte.

7. Eteignez toute cigarette ou pipe, tout cigare ou toute autre

chaleur incandescente.

8. Ne faites jamais le plein a I'interieur.

9. N'enlevez jamais le capuchon d'essence et n'ajoutez pas

d'essence pendant que le moteur tourne ou s'il est chaud.

Laissez le moteur refroidir pendant au moins deux minutes avant

de faire le plein.

10. Ne faites jamais deborder le reservoir. Laissez un espace d'un

demi-pouce environ pour permettre I'expension du carburant.

11. Resserrez bien le capuchon d'essence.

12. En cas de debordement, essuyez toute eclaboussures de

carburant ou d'huile et enlevez tousles debris imbibes

d'essence. Deplacez la machine & une autre endroit. Attendez 5

(cinq) minutes avant de mettre en marche le moteur.

13. Ne remisezjamais la machine ou les bidons d'essence

I'interieur s'il y a une flamme, une etincelle (chauffe-eau &gaz,

radiateur, s@che-linge, etc.).

14. Limitez les risques d'incendie en debarrassant le moteur des

brins d'herbe, feuilles et autres saletes. Essuyez les

eclaboussures de carburant ou d'huile et enlevez tousles debris

imbibes d'essence.

15. Laissez la machine refroidir pendant au moins 5 minutes avant

de la remiser.

Entretieng_n_ral:

1. Ne faites jamais fonctioner la machine dans un local clos car les

gaz d'echappement du moteur contiennent du monoxyde de

carbone, un gaz inodore tres dangereux.

2. Avant de nettoyer, de reparer ou d'examiner la machine, verifiez

que la lame et toutes les pieces mobiles se sont immobilisees.

Debranchez le fil de la bougie et mettez-le & la terre contre le

moteur pour emp6cher tout demarrage accidentel.

3. Verifiez souvent que la lame et les boulons de montage du

moteur sont bien serres. Examinez visuellement la lame pour

detecter toute usure excessive, tout fendillement. Remplacez-la

avec une lame authentique seulement (du liste de pi_ces qui se

trouve dans cette notice). <<L'emploide pieces non conformes

aux caracteristiques de I'equipement d'origine peut causer des

performances inferieures et reduire la securit&>>

4. La lame est coupante et peut causer des blessures graves.

Enveloppez la lame avec un chiffon ou portez des gants et faites

tres attention en le manipulant.

5. Assurez-vous que tousles ecrous, boulons et vis sont bien

serres pour que I'equipement soit toujours en bon etat de

marche.

6. Ne modifiez jamais les dispositifs de securit& Verifiez souvent

qu'ils fonctionnent bien.

La page charge ...

MTD 11A-083F800 Le manuel du propriétaire

Marque: MTD

Modèle: 11A-083F800

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: MTD 11A-083F800 Owner's manual

Documents connexes

MTD 60-1616-6 Manuel utilisateur

MTD 11A-083F800 Le manuel du propriétaire

MTD 11A-083F800 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents