Poulan Pro PR621 Mode d'emploi

OWNER'S MANUAL

MODEL NUMBER:

PR621

SNOW THROWER

Always Wear Eye Protection During Operation

IMPORTANT MANUAL Do Not Throw Away

WARNING:

Read the Owner's Manual and

fol low all Warnings and Safety

In struc tions. Fail ure to do so

can result in serious injury.

436430 Rev. 3 09.01.10 TH

Printed in the U.S.A.

2

Safe Operation Practices for Walk-Behind Snow Throwers

IMPORTANT: This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury.

(d) Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place containers

on the ground, away from your vehicle, before filling.

(e) When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the ground.

If this is not possible, then refuel such equipment

on a trailer with a portable container, rather than

from a gasoline dispenser nozzle.

(f) Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times, until refueling

is complete. Do not use a nozzle lock-open device.

(g) Replace gasoline cap securely and wipe up spilled

fuel.

(h) If fuel is spilled on clothing, change clothing im-

mediately.

5. Use extension cords and receptacles as specified by

the manufacturer for all units with electric drive motors

or electric starting motors.

6. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

7. Always wear safety glasses or eye shields during op-

eration or while performing an adjustment or repair to

protect eyes from foreign objects that may be thrown

from the machine.

Operation

1. Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

Training

1. Read, understand and follow all instructions on the

machine and in the manual(s) before operating this

unit. Be thoroughly familiar with the controls and the

proper use of the equipment. Know how to stop the

unit and disengage the controls quickly.

2. Never allow children to operate the equipment. Never

allow adults to operate the equipment without proper

instruction.

3. Keep the area of operation clear of all persons, par-

ticularly small children.

4. Exercise caution to avoid slipping or falling, especially

when operating the snow thrower in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is

to be used and remove all doormats, sleds, boards,

wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before

starting the engine (motor) if equipped.

3. Do not operate the equipment without wearing adequate

winter garments. Avoid loose fitting clothing that can

get caught in moving parts. Wear footwear that will

improve footing on slippery surfaces.

4. Handle fuel with care; it is highly flammable

(a) Use an approved fuel container.

(b) Never add fuel to a running engine or hot engine.

(c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to

give best possible dependability and per for mance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We

have competent, well-trained tech ni cians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower prop er ly.

Always observe the “SAFETY RULES”.

Look for this symbol to point out im por tant

safety precautions. It means CAUTION!!! BE-

COME ALERT!!! YOUR SAFE TY IS IN VOLVED.

WARNING: Always disconnect spark plug wire

and place it where it can not con tact plug in or-

der to pre vent ac ci den tal start ing when setting

up, trans port ing, ad just ing or making re pairs.

WARNING: This snow thrower is for use on

sidewalks, driveways and other ground level

surfaces. Caution should be exercised while

using on sloping surfaces. Do not use snow

thrower on surfaces above ground level such

as roofs of residences, garages, porch es or

other such structures or buildings.

WARNING: Engine exhaust, some of its con-

stit u ents, and certain vehicle com po nents

contain or emit chem i cals known to the State

of Cal i for nia to cause can cer and birth defects

or oth er re pro duc tive harm.

CAUTION: Muffler and other engine parts be-

come extremely hot during operation and remain

hot after engine has stopped. To avoid severe

burns on contact, stay away from these areas.

WARNING: Snow throwers have ex posed

rotating parts, which can cause severe injury

from contact, or from material thrown from the

discharge chute. Keep the area of operation

clear of all persons, small children and pets at

all times including startup.

3

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for

and using your snow thrower.

• Follow the instructions under “Maintenance” and “Stor-

age” sec tions of this manual.

PRODUCT SPECIFICATIONS

Gasoline Capacity 1.6 Quarts (1,5 Liters)

and Type: Unleaded Regular only

Oil Type SAE 30 (above 50°F)

(API SG–SL): SAE 5W-30 or 10W-30

(32° to 50°F)

SAE 5W-30 (below 32°F)

Oil Capacity: 16 Ounces (0,47 Liters)

Spark Plug: F6RTC

Gap: 0.030" (0,762 mm)

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE SNOW

THROWER HOUSING (Figure 1).

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

Figure 1

SERIAL

CATALOG

PRODUCT MAINTENANCE LEVEL

MODEL

CONFORMS TO ANSI B71.3-2005 SAFETY STANDARDS

407435

FOR SERVICE CALL 1-800-849-1297

ASSEMBLED IN U.S.A.

Orangeburg, SC 29118

2. Exercise extreme caution when operating on or cross-

ing gravel drives, walks, or roads. Stay alert for hidden

hazards or traffic.

3. After striking a foreign object, stop the engine (motor),

disconnect the cord on electric motors, thoroughly

inspect the snow thrower for any damage, and repair

the damage before restarting and operating the snow

thrower. Remove key.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the cause.

Vibration is generally a warning of trouble.

5. Stop the engine (motor) whenever you leave the op-

erating position, before unclogging the auger housing

or discharge chute, and when making any repairs,

adjustments or inspections.

6. When cleaning, repairing or inspecting the snow thrower,

stop the engine and make certain the auger blades and

all moving parts have stopped. Remove key.

7. Do not run the engine indoors, except when starting

the engine and for transporting the snow thrower in or

out of the building. Open the outside doors; exhaust

fumes are dangerous.

8. Exercise extreme caution when operating on slopes.

9. Never operate the snow thrower without proper guards,

and other safety protective devices in place and working.

10. Never direct the discharge toward people or areas

where property damage can occur. Keep children and

others away.

11. Do not overload the machine capacity by attempting

to clear snow at too fast a rate.

12. Never operate the machine at high transport speeds

on slippery surfaces. Look behind and use care when

operating in reverse.

13. Disengage power to the auger blades when snow

thrower is transported or not in use.

14. Use only attachments and accessories approved by

the manufacturer of the snow thrower.

15. Never operate the snow thrower without good visibility

or light. Always be sure of your footing, and keep a firm

hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating auger blades

inside the discharge chute is the most common

cause of injury associated with snow throwers.

Never use your hand to clean out the discharge

chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the auger blades have

stopped rotating.

3. Always use a clearing tool at least 15 inches long.

Maintenance and Storage

1. Check shear bolts and other bolts at frequent intervals

for proper tightness to be sure the equipment is in safe

working condition.

2. Never store the machine with fuel in the fuel tank inside

a building where ignition sources are present such as

hot water heaters, space heaters, or clothes dryers.

Allow the engine to cool before storing in any enclosure.

3. Always refer to operator’s manual for important details

if the snow thrower is to be stored for an extended

period.

4. Maintain or replace safety and instruction labels, as

necessary.

5. Run the machine a few minutes after throwing snow

to prevent freeze-up of the collector/impeller.

4

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Com-

pare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.

Save this manual for future reference.

These symbols may appear on your snow thrower or in literature supplied with the product. Learn and under-

stand their meaning.

IMPORTANT: Safety and instruction decals are located near areas of potential danger. Replace damaged decals.

$!.'%2

/2ª7!2.).'

2%!$ª!.$ª&/,,/7ª!,,ª3!&%49ª).&/2-!4)/.

!.$ª).3425#4)/.3ª"%&/2%ª53%ª/&ª4()3ª02/$5#4

+%%0ª4(%3%ª).3425#4)/.3ª&/2ª&5452%ª2%&%2%.#%

/),

/&&

%.').%

/.

%.').%

#(/+%

)'.)4)/.ª+%9

).3%24ª4/ª34!24

!.$ª25.

05,,ª/54ª4/ª34/0

&5%,

02)-%2



MAINTENANCE ..................................................... 11-15

STORAGE ................................................................... 16

TROUBLESHOOTING ................................................ 17

REPAIR PARTS ..................................................... 18-26

WARRANTY ................................................................ 30

SAFETY RULES ........................................................ 2-3

PRODUCT SPECIFICATIONS ...................................... 3

CUSTOMER RESPONSIBILITIES ................................ 3

SAFETY AND INSTRUCTIONAL DECALS ................. 4

SETUP........................................................................ 5-6

OPERATION ............................................................ 7-11

TABLE OF CONTENTS

5

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description Qty. Use

1.

No parts required – Unfold the handle.

2.

Carriage bolts

Flange nuts

Washers

Knob

Chute

Deflector

5

4

2

1

Install the discharge chute.

1. Unfolding the Handle

Procedure

1. Loosen the two handle knobs and pull out the two

handle bolts until you can move the handle freely and

rotate the handle to the operating position (Figure 2).

2. Tighten the handle knobs until they are snug (Figure 3).

2. Installing the Discharge

Chute

5 Carriage bolts

4 Flange nuts

2 Washers

1 Knob

1 Chute

1 Deflector

Procedure

Install the discharge chute as shown (Figure 4).

IMPORTANT: Do not overtighten the flange nuts;

otherwise you may damage the discharge chute.

Figure 3

1. Handle knobs 2. Handle bolt

Figure 2

2

1

Figure 4

1. Deflector

2. Carriage bolts

3. Flange nuts

2

6

3

4

5

1

4. Washer

5. Knob

6. Discharge chute

6

3. Filling the Engine with Oil

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service

classification SG–SL. Select the oil's SAE viscosity grade

according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)

improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption when used above

32°F. Check your engine oil level more frequently to avoid

possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once

a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine

and after each five (5) hours of continuous use. Tighten oil

fill cap / dipstick securely each time you check the oil level.

NOTE: 10W30 synthetic oil is acceptable for use in cold

temperatures.

1. Move the snowthrower to a level surface.

2. Clean around the dipstick (Figure 6).

NOTE: Dipstick location may vary depending on engine

type.

3. Remove either side mounted filler cap dipstick or high

oil fill dipstick and wipe it clean.

4. Insert the dipstick into the filler neck and turn clockwise

until fully seated. Then remove the dipstick by turning

it counter-clockwise.

5. Fill oil to "FULL" on dipstick with the recommended oil.

6. Securely screw in the oil filler cap/dipstick.

Figure 5

Product Overview

Figure 7

1. Discharge chute

2. Chute deflector handle

3. Fuel tank cap

4. Control bar

5. Recoil start handle

6. Primer

7. Choke lever

8. Electric-start button

9. Oil drain plug

10. Drive belt cover

*11. Oil fill cap/dipstick

12. Ignition key

13. Chute deflector

5

9

2

6

10

1

7

*11

3

8

12

4

13

* Dipstick location may vary depending on engine type.

1. Oil filler cap/dipstick

Figure 6

1

Fill if oil is

below letter

“L” on the

ller cap

Fill if oil

is below

“Add”

on the

dipstick

7

Operation

NOTE: Determine the left and right sides of the machine

from the normal operating position.

• Gasoline is extremely flammable and explosive.

A fire or explosion from gasoline can burn you

and others.

• To prevent a static charge from igniting the gaso-

line, place the container and/or snowthrower on

the ground before filling, not in a vehicle or on

an object.

• Fill the tank outdoors when the engine is cold.

Wipe up spills.

• Do not handle gasoline when smoking or around

an open flame or sparks.

• Store gasoline in an approved fuel container, out

of the reach of children.

• Do not tip the snowthrower with fuel in the fuel

tank.

The operation of any snow thrower can result

in foreign objects thrown into the eyes, which

can result in severe eye damage. Always wear

safety glasses or eye shields while operating

your snow thrower or performing any ad just-

ments or repairs. We recommend standard safe ty glasses

or a wide vision safety mask worn over spectacles.

IMPORTANT: Know how to operate all controls before

adding fuel or attempting to start the engine.

Filling the Fuel Tank

Fill the fuel tank with fresh unleaded gasoline, do not

exceed 87 octane rating (Figure 8).

IMPORTANT: Do not add oil to the gasoline.

IMPORTANT: Do not use E85 blended fuels. This engine

is not E20/E30/E85 compatible. Alternative fuels with

high alcohol content can cause hard starting, poor engine

performance, and may cause internal engine damage.

Checking the Engine Oil

Level

NOTE: 10W30 synthetic oil is acceptable for use in cold

temperatures.

1. Move the snowthrower to a level surface.

2. Clean around the dipstick (Figure 9).

NOTE: Dipstick location may vary depending on engine

type.

3. Remove either side mounted filler cap dipstick or high

oil fill dipstick and wipe it clean.

4. Insert the dipstick into the filler neck and turn clockwise

until fully seated. Then remove the dipstick by turning

it counter-clockwise.

5. Fill oil to "FULL" on dipstick with the recommended oil.

6. Securely screw in the oil filler cap/dipstick.

NOTE: Running the engine with a low oil level can cause

engine damage. Always check the engine oil before start up.

NOTE: Running the engine with too much oil may cause

engine damage and excess smoke in the exhaust. Always

check the engine oil level before start up.

NOTE: For best results, purchase only the quantity of

gasoline that you expect to use in 30 days. Otherwise,

you may add fuel stabilizer to newly purchased gasoline

to keep it fresh for up to 6 months.

Figure 8

1. Oil filler cap/dipstick

Figure 9

1

Fill if oil is

below letter

“L” on the

ller cap

Fill if oil

is below

“Add”

on the

dipstick

8

Starting the Engine

1. Push key in (Figure 10).

2. Move choke lever to left position (Figure 11).

3. Firmly push in the primer 3 times with your thumb,

holding the primer in a for a second before releasing

it each time (Figure 12).

NOTE: Remove your glove when you push in the primer

so that air cannot escape from the primer hole.

IMPORTANT: Do not use the primer or the choke if the

engine has been running and is hot. Excessive priming

may flood the engine and prevent it from starting.

4. Connect an extension cord to the snowthrower and

plug the other end into a three-hole grounded 120

volt A.C. receptacle and push the electric-start button

(Figure 13), or pull the recoil start handle (Figure 14).

NOTE: Use only a UL-listed, 16-gauge extension cord

recommended for outdoor use that is not longer than 50

feet (15 m).

1. Primer

Figure 12

1

Figure 10

1. Key

1

Figure 13

1. Electric start button

1

1. Choke lever

Figure 11

1

9

Engaging the Auger Blades

To engage the auger blades, hold the control bar against

the handle (Figure 15).

Disengaging the Auger

Blades

To disengage the auger blades, release the control bar

(Figure 16).

The electrical cord can become damaged, causing

a shock or fire.

Thoroughly inspect the electrical cord before plug-

ging it into a power source. If the cord is damaged,

do not use it to start the snowthrower. Replace or

repair the damaged cord immediately. Contact an

Authorized Service Dealer for assistance.

IMPORTANT: Run the electric starter no more than 10

times at intervals of 5 seconds on, then 5 seconds off.

Running the electric starter extensively can overheat and

damage it. If the engine does not start after this series

of attempts, wait at least 40 minutes to allow the starter

to cool before attempting to start it again. If the engine

does not start after the second series of attempts, take

the snowthrower to an Authorized Service Dealer for

service.

NOTE: If you pull the recoil handle and feel no resistance,

the starter may be frozen. Thaw out the starter before

attempting to start the snowthrower.

5. While the engine is running, move the choke lever

slowly to the right position.

6. Unplug the extension cord from the power source and

the snowthrower (Figure 13).

Unplug the power cord whenever you are not start-

ing the snowthrower.

Figure 15

1. Control bar

1

Figure 16

1. Control bar

1

1. Recoil start handle

Figure 14

1

10

Stopping the Engine

To stop the engine, pull key out (Figure 17).

Adjusting the Discharge

Chute and Chute Deflector

To adjust the discharge chute, move deflector chute handle

left or right to desired position (Figure 18).

To raise or lower the angle of the chute deflector, loosen

the chute deflector knob on the chute deflector and move

the chute deflector up or down (Figure 18).

1. Chute deflector knob

2. Chute deflector

3. Chute handle

Figure 18

1

2

3

Clearing a Clogged

Discharge Chute

Preventing Freeze-up after

Use

• Let the engine run for a few minutes to prevent moving

parts from freezing. Stop the engine, wait for all mov-

ing parts to stop, and remove ice and snow from the

snowthrower.

• Clean off any snow and ice from the base of the chute.

• Rotate the discharge chute left and right to free it from

any ice buildup.

• With the ignition key in the Off position, pull the recoil

starter handle several times or connect the electrical

cord to a power source and the snowthrower and push

the electric start button once to prevent the recoil starter

and/or the electric starter from freezing up.

• In snowy and cold conditions, some controls and mov-

ing parts may freeze. Do not use excessive force when

trying to operate frozen controls. If you have difficulty

operating any control or part, start the engine and let

it run for a few minutes.

Hand contact with the rotating auger blades

inside the discharge chute is the most common

cause of injury associated with snow throwers.

Never use your hand to clean out the discharge

chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the auger blades have

stopped rotating.

3. Always use a clearing tool at least 15 inches long, not

your hands (Figure 19).

Figure 19

Figure 17

1. Key

1

11

Operating Tips

The auger blades can throw stones, toys, and

other foreign objects and cause serious personal

injury to the operator or to bystanders.

• Keep the area to be cleared free of all objects

that the auger blades could pick up and throw.

• Keep all children and pets away from the area

of operation.

• Do not operate snow thrower if weather condi-

tions im pair visibility. Throwing snow dur ing

a heavy, windy snowstorm can blind you and

be hazardous to the safe operation of the snow

thrower.

Maintenance

NOTE: Determine the left and right sides of the machine from the normal operating position.

• The best time to remove snow is the early morning.

At this time the snow is usually dry and has not been

exposed to the direct sun and warming tem per a tures.

• Slightly overlap each successive path to ensure all

snow will be removed.

• Throw snow downwind whenever possible.

• For extremely heavy snow, re duce the width of snow

removal by over lap ping previous path and moving

slowly.

• Keep engine clean and clear of snow during use. This

will help air flow and extend engine life.

• After snow-throwing is completed, allow engine to run

for a few minutes to melt snow and ice off the engine.

• Clean the entire snow thrower thoroughly after each

use and wipe dry so it is ready for next use.

12

Adjusting the Control Cable

Checking the Control Cable

Release the control bar to remove the slack in the control

cable (Figure 20).

IMPORTANT: The control cable must contain some slack

when you disengage the control bar for the auger blades

to stop properly.

NOTE: You may need to adjust the control cable from

position 1 (default) to position 2 if you notice belt slip

when the control bar is engaged.

NOTE: If the control cable is adjusted to position 2,

ensure that the auger stops properly when the control bar

is released

Inspecting the Auger Blades

Before each session, inspect the auger blades for wear.

When a auger blade edge has worn down have an

Authorized Service Dealer replace the auger blades and

the scraper (Figure 22).

Figure 22

1. Auger blades 2. Scraper

1

2

Adjusting the Control Cable

1. With the control bar disengaged, unhook and move

the control cable to the highest position. (Figure 21).

Figure 20

1. Control bar

1

1. Control bar

2. Adjuster link

3. Cable positions

Figure 21

1

2

3

Position 1: Default position

(Lower Hole as shown in illustration)

Position 2

13

Changing the Engine Oil

Run the engine a few minutes before changing the

oil to warm it. Warm oil flows better and carries more

contaminants.

4. Place an oil drain pan under the oil drain plug, remove

the oil drain plug, and tip the snowthrower backward and

drain the used oil in the oil drain pan (Figure 23).

5. After draining the used oil, return the snowthrower to

the operating position.

6. Install the oil drain plug and torque to 145-150 in-lbs

(17 N-m).

NOTE: Dipstick location may vary depending on engine

type.

7. Clean around the oil filler cap/dipstick (Figure 24).

8. Unscrew the oil fill cap/dipstick and remove it

(Figure 24).

9. With the snowthrower in the operating position, care-

fully pour oil into the oil fill hole until "Full" on the fill

cap/dipstick line (Figure 26).

Max fill: 18 oz. (0.5 l), type: automotive detergent oil with

an API service classification of SJ, SL, or higher.

Use Figure 25 below to select the best oil viscosity for

the outdoor temperature range expected:

Figure 24

1. Oil fill cap/dipstick

1

Figure 25

NOTE: 10W30 synthetic oil is acceptable for use in cold

temperatures.

10. Screw in the oil fill cap/dipstick and hand tighten it

securely.

11. Wipe up any spilled oil.

12. Dispose of the used oil properly at a local recycling

center.

The engine oil will be hot. Avoid skin contact

with the used engine oil.

Figure 23

1. Oil drain plug

1

1. Move snowthrower to a level surface.

2. Run snowthrower until all fuel has been depleted.

3. Remove ignition key.

Figure 26

Fill if oil is

below letter

“L” on the

ller cap

Fill if oil

is below

“Add”

on the

dipstick

14

Servicing the Spark Plug

Use a NGK BPR6ES, Champion RN9YC, or BOSCH

WR6DC spark plug or equivalent.

1. Stop the engine and wait for all moving parts to stop.

2. Rotate the discharge chute so that it faces forward.

3. Remove the discharge chute, the discharge chute

handle by removing the three carriage bolts and flange

nuts (Figure 27).

4. Remove the six screws that secure the shroud as-

sembly (Figure 28).

5. Remove the oil fill cap.

6. Remove the shroud assembly (Figure 28).

7. Install the oil fill cap.

8. Disconnect the spark plug wire from the spark plug

(Figure 29).

9. Clean around the spark plug.

10. Remove the spark plug from the cylinder head.

IMPORTANT: Replace a cracked, fouled, or dirty spark

plug. Do not clean the electrodes because grit entering

the cylinder can damage the engine.

11. Set the gap on the plug to 0.030 inch (0.76 mm)

(Figure 30).

12. Install the spark plug and torque it to 20–22 ft-lb (27–30

N-m).

13. Connect the spark plug wire to the spark plug

(Figure 29).

14. Remove the oil fill cap.

15. Install the shroud with the screws removed in step 4

(Figure 28).

NOTE: Ensure that the shroud assembly fits together in

the side grooves.

16. Install the oil fill cap.

17. Install the discharge chute, and the discharge chute

handle onto the snowthrower using the hardware re-

moved in step 3 (Figure 27).

1. Spark plug wire

Figure 29

1

Figure 30

0.030 inch

(0.76 mm)

1. Screw 3. Oil fill cap

2. Shroud assembly

Figure 28

1

2

3

Figure 27

2

3

1

1. Discharge chute 2. Carriage bolts

3. Flange nuts

15

Replacing the Drive Belt

If drive belt becomes worn, oil-soaked, excessively

cracked, frayed, or otherwise damaged, replace the belt.

1. Remove the drive side cover by removing the six screws

as shown in (Figure 31).

2. Press down on front of idler arm to release the belt

tension (Figure 31).

3. Remove the drive belt from the drive pulley (Figure 31).

4. Install the new drive belt, routing it as shown in

(Figure 32).

NOTE: Route the new drive belt first around the engine

pulley, then the idler pulley, and finally around the drive

pulley while pressing down on the front of the idler arm.

(Figure 32).

5. Install the drive side cover with the screws removed in

step 1.

NOTE: Ensure that the drive belt is properly adjusted

and operating; refer to Checking the Control Cable and

Adjusting the Control Cable in the Maintenance section

of this manual.

1. Drive side cover

2. Screw

3. Drive pulley

4. Idler arm

Figure 31

1

2

7

4

6

5

3

5. Idler pulley

6. Engine pulley

7. Drive belt

2

1. Idler arm

2. Idler pulley

3. Engine pulley

4. Drive pulley

Figure 32

1

3

2

4

16

Storage

Storing the Snowthrower

Immediately prepare your snow thrower for storage at

the end of the season or if the unit will not be used for 30

days or more.

WARNING: Never store the snow thrower with

gaso line in the tank in side a build ing where fumes

may reach an open flame, spark or pilot light as

on a fur nace, water heater, clothes dryer or gas

ap pli ance. Allow the engine to cool be fore storing

in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time,

clean it thor oughly, re move all dirt, grease, leaves, etc.

Store in a clean, dry area.

1. Clean entire snow thrower after each use.

2. Inspect and replace belts, if necessary (See “Replace-

ing the Drive Belt” sec tion of this manual).

3. Be sure that all nuts, bolts, screws, and pins are securely

fas tened. Inspect moving parts for damage, breakage

and wear. Replace if nec es sary.

4. Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

FUEL SYS TEM

IMPORTANT: It is important to prevent gum deposits from

forming in essential fuel system parts such as carburetor,

fuel hose, or tank during storage. Also, alcohol blended

fuels (called gasohol or using ethanol or methanol) can

attract moisture which leads to separation and formation

of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage.

• Empty the fuel tank by starting the engine and letting

it run until the fuel lines and car bu re tor are empty.

• Never use engine or carburetor cleaner prod ucts in

the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min i-

miz ing the formation of fuel gum deposits during stor age.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 min utes after adding stabilizer to

allow the stabilizer to reach the carburetor. Do not empty

the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine

oil. (See “Changing the Engine Oil” section of this man ual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole

into cylinder.

3. Pull recoil starter handle slowly a few times to dis trib ute

oil.

4. Replace with new spark plug.

OTHER

• Remove safety ignition key; store it in a safe place.

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your snow thrower indoors and cover

it to protect it from dust and dirt.

• Cover your snow thrower with a suitable pro tec tive

cover that does not retain moisture. Do not use plastic.

Plastic cannot breathe, which allows con den sa tion to

form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/

exhaust area is still warm.

17

Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.

equipped) in OFF position.

2. Safety ignition key 2. Insert safety ignition key.

is not inserted.

3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.

4. Throttle in STOP position 4. Move throttle to FAST position

(or ON/OFF switch is OFF). (or ON/OFF switch to ON position).

5. Choke in OFF position. 5. Move to FULL position.

6. Primer not depressed. 6. Prime as instructed in the Operation section of this manual.

7. Engine is flooded. 7. Wait a few minutes before restarting, DO NOT prime.

8. Spark plug wire is 8. Connect wire to spark plug.

disconnected.

9. Bad spark plug. 9. Replace spark plug.

10. Stale fuel. 10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

11. Water in fuel. 11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

Loss of power 1. Spark plug wire loose. 1. Reconnect spark plug wire.

2. Throwing too much snow. 2. Reduce speed and width of swath.

3. Fuel tank cap is covered 3. Remove ice and snow on and around fuel tank cap.

with ice or snow.

4. Dirty or clogged muffler. 4. Clean or replace muffler.

5. Improper cable length. 5. Adjust cable.

Engine idles or 1. Choke is in FULL position. 1. Move choke to OFF position.

runs roughly 2. Blockage in fuel line. 2. Clean fuel line.

3. Stale fuel. 3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

4. Water in fuel. 4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

5. Carburetor is in need of 5. Contact an authorized service center/department.

adjustment or overhaul.

Excessive 1. Loose parts or damaged 1. Tighten all fasteners. Replace damaged parts. If vibration

vibration augers or impeller. remains, contact an authorized service center/department.

Recoil starter 1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN”

is hard to pull in the Operation section of this manual.

Loss of traction 1. Drive belt is worn. 1. Check / replace drive belt.

drive / slowing 2. Drive belt is off of pulley. 2. Check / reinstall drive belt.

of drive speed 3. Auger blades worn. 3. Contact an authorized service center/department.

Loss of snow 1. Auger belt is off of pulley. 1. Check / reinstall auger belt.

discharge or 2. Auger belt is worn. 2. Check / replace auger belt.

slowing of 3. Clogged discharge chute. 3. Clean snow chute.

snow discharge 4. Augers / impeller jammed. 4. Remove debris or foreign object from augers / impeller.

Troubleshooting

PROBLEM CAUSE CORRECTION

See appropriate section in manual unless directed to an authorized service center/department.

18

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96182000300)

CHUTE ASSEMBLY

9

10

11

1

2

3

4

5

6

19

8

20

7

4

6

15

21

19

15

16

17

18

SSST-Chute asm_5

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

19

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96182000300)

CHUTE ASSEMBLY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY PART

NO. NO. QTY DESCRIPTION

1 434877 1 CHUTE.RATCHETING.PLASTIC.W/GRV

2 434876X431 2 PLATE.CHUTE.RETAINER

3 434875X431 1 PLATE.CHUTE.BASE

4 17411312 6 BOLT.HEX.WSH.HD.13-16 X 3/4

5 434885X428 1 HANDLE.CHUTE.MS428

6 73970500 4 NUT.LOCK.HX.W/INS 5/16-18 UNC PL

7 434879 1 SPRING.RATCHET.ARM

8 81328 1 BOLT.SHOULDER.1/4-20 UNC X .94

9 434878 1 ARM.CHUTE.RATCHET

10 132004 1 HEX.NUT.1/4-20 NYLON LOCKING

11 435980X428 1 PLENUM

15 437318 5 CARRIAGE.BOLT

16 434884X428 1 CHUTE

17 189713X428 1 HANDLE.KNOB

18 434886X428 1 DEFLECTOR.CHUTE

19 19131316 3 WASHER

20 19132416 1 WASHER.RATCHET.PAWL

21 428867 1 BOLT

20

KEY PART

NO. NO. QTY DESCRIPTION

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96182000300)

HANDLE ASSEMBLY

1

2

3

4

5

6

SSST-Handle asm_1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

1 434805X431 1 BAIL.HANDLE.PAINT.MS431

2 434786X431 1 HANDLE.PNT.UPPER.SSST

3 434806 1 CONTROL.CABLE

4 189713X428 2 KNOB.HANDLE.BLACK

5 191574 2 BOLT.HANDLE.BLACK PATCHED

6 145006 1 CLIP.PUSH-IN.HINGED

La page charge ...

Poulan Pro PR621 Mode d'emploi

Poulan Pro PR621 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents