ASA Electronics JENSEN JMS32 Le manuel du propriétaire

Marque: ASA Electronics

Modèle: JENSEN JMS32

Catégorie: Récepteurs multimédia de voiture

Taper: Le manuel du propriétaire

D E S I G N E D T O M O V E Y O U

[ ]

JMS32

Owner’s Manual

JMS32

CONTENTS

Introduction.....................................................................................................................................................1

Features...................................................................................................................................................1

Box Content..............................................................................................................................................1

Compliance...............................................................................................................................................1

Safety Information.....................................................................................................................................2

Installation......................................................................................................................................................3

Mounting the Radio....................................................................................................................................3

Auxiliary Input...........................................................................................................................................3

Line Output...............................................................................................................................................3

Wiring Diagram.........................................................................................................................................4

Operation........................................................................................................................................................5

Basic Functions.........................................................................................................................................5

Audio Menu...............................................................................................................................................5

System Menu ............................................................................................................................................5

Radio Mode...............................................................................................................................................6

USB Mode.................................................................................................................................................6

Playback Menu (Repeat/Random)...............................................................................................................7

Auxiliary Input Mode..................................................................................................................................7

Bluetooth Operation...................................................................................................................................8

Canada Statement.........................................................................................................................................10

Troubleshooting.............................................................................................................................................11

Speciﬁcations................................................................................................................................................11

JMS32

INTRODUCTION

Thank for choosing a Jensen product. We hope you will ﬁnd the instructions in this owner's manual clear and easy to follow. If

you take a few minutes to look through it, you'll learn how to use all the features of your new Jensen receiver for maximum

enjoyment.

Features

● Waterproof iPx6

● UV and Corrosion Resistant

● Dimmable Backlit LCD Control

● AM/FM Tuner (US/EURO)

● 24 Programmable Presets (12 AM, 12 FM)

● Weather Band Tuner

● Electronic Bass, Treble, Balance and Fader Controls

● USB MP3/WMA Player

● Rear Auxiliary Audio Input (RCA)

● Rear Auxiliary Audio Output (RCA)

● 4-Channel Ampliﬁed Audio Output

● Bluetooth (Supports A2DP and AVRCP)

Box Content

● JMS32 Radio

● Radio Mounting Bracket

● Screw Posts (x2)

● Locking Hex Nuts (x2)

● Washers (x2)

Compliance with FCC Rules

Compliance with FCC Rules (U.S.A Only)

This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against Harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful Interference to radio communications.

FCC WARNING

● Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

● Proper connections must be used for connection to a host computer and/or peripherals in order to meet FCC emission

limits.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance 20cm between the radiator & your body.

JMS32

Safety Information

● To ensure full satisfaction with the product, please read the entire instruction manual.

● Keep instructions for future reference.

● Follow all operation guidelines and adhere to all safety warnings and cautions to ensure safe use.

● Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that

produce heat.

● Only use attachments/accessories speciﬁed by the manufacturer.

● Never use harsh cleaning agents. Clean only with a dry cloth.

When Driving

Keep the volume level low enough to be aware of the road and traﬃc conditions.

Protect from Water

Do not submerge, as this can cause electrical shorts, ﬁre or other damage.

Protect from High Temperatures

Exposure to direct sunlight for an extended period of time can produce very high temperatures inside your vehicle. Give the

interior a chance to cool down before starting playback. Do not mount the radio within close proximity of the engine

compartment.

Use the Proper Power Supply

This product is designed to operate with a 12 volt DC negative ground battery system.

WARNING:

● DO NOT OPEN, DISASSEMBLE OR ALTER THE UNIT IN ANY WAY. Doing so may result in ﬁre, electric shock or product

damage.

● USE THE CORRECT AMPERE RATING WHEN REPLACING FUSE. Failure to do so may result in ﬁre, electric shock or

product damage.

● DO NOT INSTALL IN LOCATIONS THAT MIGHT HINDER VEHICLE OPERATION. Doing so may obstruct vision or

hamper movement which can result in a serious accident.

● INSTALL THE WIRING SO THAT IT IS NOT CRIMPED OR PINCHED BY SCREWS ORSHARP METAL EDGES. Route

the cables away from moving parts or sharp pointed edges. This will prevent crimping and damage to the wiring. If the

wiring must pass through a metal hole, be sure to use a rubber grommet to prevent the wire's insulation from being cut by

the metal edge of the hole. It is also recommended to apply sealing caulk to any opening that may potentially allow water

to enter.

● Be sure to choose a location that is ﬂat and has clearance above the unit to prevent any damage, as well as allow for

ventilation.

● Before drilling any holes, carefully inspect the area underneath and behind the mounting surface where the device will be

mounted to make sure it will not interfere with existing wires, fuel lines, the fuel tank or any other objects that could be

damaged.

● Always disconnect the vehicle negative battery terminal during installation to prevent accidental shorting.

INSTALLATION

Mounting the Radio

1. Choose a mounting location on the dash board or instrument panel that will allow room behind to run radio cables to the

power source. Consider how you will use the AUX IN, LINEOUT and USB connectors and route the appropriate extension

cables to an accessible area.

2. Cut a hole in the dash board using the template provided in the back of this manual. At least 3 ¾”depth is needed to mount

the radio.

IMPORTANT! Do not mount this unit where it can be submerged in water.

3. Slide the included spring washers (B) over the screw posts (A) and attach the screw posts to the back of the radio.

4. Place the radio in front of the dashboard opening so the wiring can be brought through the opening.

5. After completing the wiring connections, turn the radio on to conﬁrm operation (vehicle accessory switch must be on). If the

radio does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn the

accessory switch oﬀ and proceed with ﬁnal mounting of the radio. Refer to the “Wiring Diagram” on page 4.

NOTE: Before ﬁnal installation, test the wiring connections to make sure the unit is connected properly and the

system works.

6. Insert the radio into the mounting hole.

7. Place the “U” bracket (C) over the screw posts and secure the radio to the dash using the included hex nuts (D). If

necessary, cut the score marks (E) on either side of the mounting bracket to custom ﬁt the bracket length for your

application. See Figure A.

JMS32

Auxiliary Input

Connect a portable audio device to the Audio Input (AUX IN RIGHT/LEFT) on the back of the unit using RCA cables.

Line Output

The Line Out connectors (LINE OUT RIGHT/LEFT) on the back of the unit output a line-level analog signal. Use this output to

connect to an external ampliﬁer.

Figure A - Installation

JMS32

Note: Do not connect the red wire to a

constant power connection. The red wire

should be connected to a vehicle connection

with switched power such as IGN or ACC.

WIRE COLOR

PURPLE

PURPLE/BLACK

GRAY

GRAY/BLACK

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

RED

BLACK

BLUE

DESCRIPTION

RIGHT REAR SPEAKER(+)

RIGHT REAR SPEAKER(-)

RIGHT FRONT SPEAKER(+)

RIGHT FRONT SPEAKER(-)

LEFT FRONT SPEAKER(+)

LEFT FRONT SPEAKER(-)

LEFT REAR SPEAKER(+)

LEFT REAR SPEAKER(-)

ACC +12V

GROUND

POWER AMP REMOTE

LINE-OUT-RIGHT

LINE-OUT-LEFT

AUX IN-RIGHT

AUX IN-LEFT

USB

ACC +12V

GROUND

FRONT LEFT SPEAKER(-)

FRONT LEFT SPEAKER(+)

REAR LEFT SPEAKER(+)

REAR LEFT SPEAKER(-)

REAR RIGHT SPEAKER(-)

REAR RIGHT SPEAKER(+)

FRONT RIGHT SPEAKER(-)

FRONT RIGHT SPEAKER(+)

POWER AMP REMOTE

GRAY

GRAY/BLACK

BLACK

YELLOW

BLACK

RED

WHITE/BLACK

GREEN

PURPLE

BLUE

GRAY

BLACK

ANTENNA

WHITE

GRAY

GREEN/BLACK

PURPLE/BLACK

FUSE 15A

Wiring Diagram

Basic Functions

Power

Press the power button (1) to turn the unit on.

Press and hold the power button (1) to enter standby mode.

Volume

Press the button (10) to increase the volume.

Press the button (2) to decrease the volume.

Press and hold either button to change the volume level continuously.

Pause/Mute

Press the button (6) to silence the audio output in tuner, AUX or USB mode. Press again to restore the previous volume

level.

Mode

Press the button (3) to select a mode of operation: AM, FM, WX, Bluetooth, AUX IN and USB.

Dimming Control

Press the button (1) to turn the dimmer on (Selected brightness level) and press again to turn the dimmer oﬀ (maximum

brightness level)

Audio Menu

Press button (8) to access the audio menu. Press the button repeatedly to adjust the following audio menu settings:

BASS, TREBLE, BALANCE, FADER and LOUD. Use the or buttons (5, 7) to choose a value for each setting.

System Menu

Press and hold button (8) to access the system menu. Press the button (8) once again to adjust the following system

menu settings: BT DEVICE, BT PAIR, DIMMER ON/OFF, DIMMER LEVEL (0 - 8), REGION (USA/EURO), PRESET VOLUME

and RESET. Use the or buttons (5, 7) to choose a value for each setting.

Reset

Press the button (6) to conﬁrm factory default restore. This function will time out after 5 seconds of inactivity and the unit will

resume normal operation. After reset, the unit will default to FM mode.

JMS32

OPERATION

Radio Mode

USA/Europe (EURO) Tuning Mode Selection

To change from USA to European tuning mode, perform the following steps:

1. Press and hold the button (8) for 3 seconds to access the system menu.

2. Press the button (8) repeatedly to cycle through the menu options (DIM > DIM LEVEL > REGION > PRE VOL >

RESET). The Region setting will display REG USA (if set to USA frequency tuning mode) or REG EUR (if set to European

frequency mode).

3. With the display showing the current tuning mode, Press the or buttons (5, 7) to change between (REG USA /

REG EUR).

Frequency Tuning

Press the or buttons (5, 7) to ﬁne tune the radio frequency.

Channel Seek

Press and hold the or buttons (5, 7) to seek strong radio frequencies.

Preset Channel Store

To manually store a favourite channel to one of the twelve preset channels, perform the following steps:

1. Press the or buttons (5, 7) to tune to the radio frequency you want to store.

2. Press and hole the favourite button (9) to access 12 presets channel list; the favourite icon & channel will be

ﬂashing on display.

3. Press the button (9) repeatedly to select desired favourite preset channel number (1-12).

4. Press the button (6) to save the station to the chosen preset channel and exit preset channel list, the favourite icon will

stop ﬂashing.

Auto Store

Press and hold the button (3) to access the tuner menu list (AUTO STORE & PRESET SCAN). Press button (3)

repeatedly until “AUTO STR” appears on the display. Press the button (6) to begin the Auto Store function and store the

strongest stations to the preset tuning channels.

NOTE: Only stations detected with suﬃcient signal strength will be stored in the preset channel automatically.

Preset Scan

Press and hold the button (3) to access the tuner menu list (AUTO STORE & PRESET SCAN). Press button (3)

repeatedly until “PRE SCAN” appears on the display. Press the button (6) to begin the Preset Scan function and listen the

strongest stations to the preset tuning channels.

Favourite Preset Channel select

Press the button (9) to select available preset channels.

USB Mode

Insert/Remove USB Device

You can connect a USB device directly to the USB interface at the rear of the radio for playback of compatible ﬁles. Playback

begins automatically.

Press the button (3) to switch to USB mode from another source.

Play/Pause (USB)

During USB playback, press the button (6) to play or pause the selected track.

Next/Previous File

Press the or button (5, 7) to select the previous or next track.

Track Select

1. Press and hold the buttons (9) to access the MP3/WMA track navigate mode.

2. Press the volume or button (10, 2) to select the desire track.

3. Press button (6) to conﬁrm to playback the track selected.

Fast Forward/Fast Reverse

Press and hold the or button (5, 7) to fast forward or fast reverse.

JMS32

Playback Menu (Repeat/Random)

Press the button (9) to select Repeat All, Repeat One and Random playback.

Repeat Play

Repeat One: to continuous repeat the selected track.

Repeat All: to repeat all tracks.

Random Play

Random Shuﬄe: To play all tracks in random, shuﬄe order.

Auxiliary Input Mode

Press the button (3) repeatedly until auxiliary input mode (AUX IN) is selected from any other modes, when a portable

device is connected to the unit.

JMS32

Bluetooth Operation

The JMS32 includes built-in Bluetooth technology that allows you to connect this unit to Bluetooth devices for streaming audio

playback.

About Bluetooth Technology

Bluetooth is a short-range wireless radio connectivity technology developed as a cable replacement for various electronic

devices. Bluetooth operates in 2.4 GHz frequency range and transmits voice and data at speeds up to 1 megabit per second.

Bluetooth was launched by a special interest group (SIG) comprised of Ericsson Inc., Intel Corp., Nokia Corp., Toshiba and IBM

in 1998, and it is currently developed by nearly 2,000 companies worldwide. The Bluetooth word mark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks is under license. Other trademarks and trade names are those of their

respective owners.

Bluetooth Menu Options

NOTE: Please note that some Bluetooth menu options are only available while the unit is in Bluetooth Audio mode.

Press and hold the button (8) to enter the menu adjustment mode. The following additional menu options are available when

the unit is in Bluetooth mode:

● BT PAIR: ON the BT PAIR screen press the button (6) to make pairing available for 120 seconds then connect using

your Bluetooth enabled device.

● BT DEVICE: Press the button (6) to view a list of previously paired mobile phone devices. Press the or

buttons (5, 7) to view devices in the list. When viewing a speciﬁc device press button (6) again to enable the

following LOCK/UNLOCK, CONNECT/DISCONNECT, or DELETE functions and press or buttons (5, 7) to cycle 

through them.

● CONNECT/DISCONNECT: To disconnect a paired device, press the button (6) to temporarily remove the

Bluetooth connection. The connection can be re-established through your phone menu by selecting the JMS32 for

connection or select the phone device name on pairing list through the radio unit and press button (6) and

select CONNECT for connection.

 LOCK/UNLOCK: The JMS32 can store up to 5 devices for Bluetooth connection.The devices are stored in a FIFO ●

(First in First Out) order. To prevent a device from being bumped from the list when more than 5 devices are used,

you can lock the device. To Lock/Unlock a device, press button (6) to change between Lock/Unlock.

 DELETE: Deleting a device removes it from the pairing list. To delete a device from the list, press the button (6). ●

To reconnect with a deleted device it must be paired again.

…

JMS32

Use /

to Navigate

the List Press / Press /

Press /

BT Device

Device 1

Device 2

Device 3

Device 4

Device 5

Lock/Unlock

Connect/Disconnect

Delete

Lock/Unlock

Connect/Disconnect

Delete

Pairing a Bluetooth Device

Before you begin, consult the owner's manual for the Bluetooth device you want to pair with the JMS32.

1. Make sure the device you intend to pair with is on and ready to receive a signal from the JMS32.

2. Press the  button (4) to enter Bluetooth mode.

3. Press and hold the  button (8) and press repeatedly until the unit display PAIR, then press  button (6). The unit

will display PAIR and count down from 120 to o. While the unit counts down, use your mobile device Bluetooth function to

search for a Bluetooth function to search for a Bluetooth device.

4. When your mobile device has completed its search, the mobile device will display the Bluetooth device name (JMS32).

5. Select JMS32. Once connected the Bluetooth Audio icon  will appear on the display.

6. Enter the pairing password (0000), if requested.

After connecting successfully, you will be able to listen to audio stored on your Bluetooth enabled device through the radio.

Answering a Call

When answering a call using the connected phone, Bluetooth audio playback will pause. After hanging up from the call, Bluetooth

audio will continue on some phones. It may be necessary to press the button (6) to resume Bluetooth audio playback.

Bluetooth Audio (A2DP)

Selecting Tracks

During playback, press  or  button (5, 7) to play the previous or next track.

Pausing Playback

During playback, press  button (6) to pause the Bluetooth audio playback. “PAUSE” will appear on the LCD. Press  button

(6) again to resume playback. If you change to another mode, playback will automatically pause. Press the button (3) to

return to Bluetooth mode and resume audio playback from your Bluetooth enabled device.

NOTE: If a Bluetooth device is disconnected due to the power being turned oﬀ or if the device goes out of range, the

unit will automatically search for the matching Bluetooth mobile device when the power is restored.

JMS32

CANADA STATEMENT

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’

exploitation est autorisée aux deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with

RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité

à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and

your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet

équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre

corps.

JMS32

TROUBLESHOOTING

Table 1: Troubleshooting

Problem Solution

No power

No AM/FM Reception

No sound

If the power supply is connected to the vehicle accessory circuits but the engine is not on , switch

the ignition key to “ACC”.

Fuse may be blown. Replace with 15 AMP ATO fuse.

Antenna cable not connected; insert antenna cable ﬁrmly.

Check volume level; increase volume if necessary.

Check power; make sure device is on.

Check device; press the play/pause button to ensure unit is not in Pause mode.

SPECIFICATIONS

General

Frequency band(s) ( for Bluetooth)..................................................................................................................2.4~2.4835GHz

Maximum radio frequency power transmitted (for Bluetooth)........................................................................................10 dBm

Power Supply Requirements.....................................................................................................DC 12 Volts, Negative Ground

Operating Voltage...................................................................................................................................................10-16V DC

Unit Dimensions..........................................................................................................................3.602" Diameter, 3.465"Deep

Mounting Dimensions.......................................................................................................................3.866" Wide, 4.465" Deep

Weight.............................................................................................................................................................................1.3lb.

FM Tuner

Tuning Range..............................................................................................................................................87.5 to 107.9 MHz

Sensitivity.........................................................................................................................................................................<5 Vμ

Stereo Separation @ 1 kHz............................................................................................................................................>30dB

AM Tuner

Tuning Range....................................................................................................................................................530-1710 KHz

Sensitivity.......................................................................................................................................................................<63 Vμ

Ampliﬁer

Max Output Power.........................................................................................................160 Watts Total (40 Watts, 4 Channel)