Hikoki RP18DA Manuel utilisateur

Catégorie
Aspirateurs
Taper
Manuel utilisateur

Ce manuel convient également à

Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this vacuum cleaner can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual BEFORE operating the vacuum cleaner. Please keep this manual available for
other users and owners before they use the vacuum cleaner. This manual should be stored in
safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet aspirateur peut entrner la mort ou
de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Prière de lire et de comprendre ce mode demploi AVANT dutiliser laspirateur. Garder ce
mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent
l’aspirateur. Ce mode demploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de este aspirador puede resultar en lesiones
de gravedad o la muerte!
Este manual contiene informacn importante sobre la seguridad del producto. Lea y
comprenda este manual ANTES de utilizar el aspirador. Guarde este manual para que
puedan leerlo otras personas antes de utilizar el aspirador. Este manual debe ser guardado
en un lugar seguro.
Model
Modèle
Modelo RP 18DA
Cordless Vacuum Cleaner
Aspirateur sans l
Aspirador inalámbrico
2
English
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction
Manual before operating or maintaining this vacuum cleaner.
Most accidents that result from vacuum cleaner operation and maintenance are caused by the failure to
observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially
hazardous situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections
which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or device damage are identi ed by WARNINGS on the
vacuum cleaner and in this Instruction Manual.
NEVER use this vacuum cleaner in a manner that has not been speci cally recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious
injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate
injury, or may cause device damage.
NOTE emphasizes essential information.
SPECIFIED CONDITIONS OF USE
The vacuum cleaner is suitable for the vacuuming of dust, solid materials (broken glass, nails etc.), with the
exception of material that is hotter than 60 °C.
The vacuum cleaner is suited for vacuuming of liquids.
This device is not designed for use by persons (including children) with physical, sensory or mental disabilities,
or with insu cient experience and/or knowledge, unless they are supervised by a person responsible for their
safety, or have received instructions on how to use the device by this person.
Pay attention to the country-speci c regulations, as well as the speci cations of the material producer.
This product is designed for commercial use, for example in hotels, schools, hospitals, factories, shops,
o ces and rental companies.
Dust containing asbestos must not be vacuumed.
In ammable dust must not be vacuumed.
No in ammable or explosive solvents, material saturated with solvent, dust that represents an explosion
hazard, liquids of any kind, thinner or material that is hotter than 60 °C are allowed to be vacuumed. This
would cause an explosion and re hazard! You are not allowed to use the device in the vicinity of in ammable
gases or substances.
The user bears sole responsibility for any damage caused by inappropriate use.
Generally accepted accident prevention regulations and the enclosed safety information must be observed.
The vacuum cleaner is suited for the separation of dry, non- ammable dust and wood dust.
The particulate collective e ciency of the HEPA lter is 99.95%.
3
English
To reduce the risk of re, electric shock, or injury:
GENERAL SAFETY INFORMATION
1. Before using the device, carefully read
through and familiarise yourself with all the
enclosed safety information and the Operating
Instructions. Keep all enclosed documentation
for future reference, and ensure that you
only pass on your device together with this
documentation.
2. Before using the device, the user must
receive information, instructions and
training material on using the device and the
materials for which it is to be used (including
details on safe disposal of the extracted
material).
SPECIAL SAFETY INSTRUCTIONS
1. For your own protection and for the
protection of your vacuum cleaner, pay
attention to all parts of the text that are marked
with this symbol!
2. Never allow children to use the device.
Children should be supervised to ensure that
they do not play with the device.
3. Caution! Only use accessories that are
included with the device or speci ed operating
Instructions. The use of other accessories may
impair safety.
4. You must not perform any work other than that
described here.
5. In the event of misuse, improper operation or
unprofessional repair work no liability shall be
assumed by us for any damage incurred.
6. Do not operate devices or accessories under
the following conditions:
- If the device has recognisable damage
(cracks/breaks),
- Battery is defective,
- If there is a suspected non-visible defect
(after a fall).
7. Only use the device with the battery cover
closed. Keep the battery cover closed, even
when the battery is not inserted.
After closing the battery cover, check to ensure
the knob for the battery cover has engaged.
8. Do not point the nozzle, hose or tube at people
or animals.
9. Never sit or stand on the device.
10. Always set up the hose so there is no danger of
tripping.
11. Do not leave the device unattended.
12. The vacuum cleaner should not be used or
stored outside.
13. IMPORTANT - This device must only be used
or stored indoors.
14. Acids, acetone and solvents can corrode the
device components.
15. Prior to any servicing work, cleaning of
the and after each use, switch o the
device and pull out the battery.
16. Steam cleaners and high-pressure cleaners
must not be used to clean the vacuum cleaner.
17. Mould contamination can result if the device is
not cleaned for an extended period, especially if
used in areas where foodstu s are processed:
Always clean and disinfect the vacuum cleaner
immediately after use.
18. Never open the device outdoors during rain or
storms.
19. Do not use the device in low (<-23°F (<-5°C)) or
very high (>104°F (>40°C)) temperatures.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical device, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS
DEVICE)
WARNING
4
English
20. The device must not be operated in areas with
an explosion hazard.
21. Ensure that the vacuum cleaner is steady.
22. If the extracted air is discharged into the room,
ensure there is an adequate air change rate (L)
in the room. Observe the regulations that apply
in your country.
23. CAUTION! This device contains dust that is
harmful to health. Discharge and maintenance
operations (including disposal of the dust
collection tanks) must only be carried out
by quali ed specialists wearing appropriate
protective clothing and equipment.
24. WARNING - general danger!
25. CAUTION! Do not use the device until you have
read the operating Instructions.
26. WARNING - Operating personnel must be
provided with appropriate instruction on how to
use this vacuum cleaner.
27. WARNING - If foam or liquid escapes from the
device, switch o immediately.
28. CAUTION! Clean the water level limiting
device/electrodes regularly and examine it for
signs of damage.
29. While the device is suitable for extracting
substances that pose a slight threat to health,
it is not appropriate for reducing wood dust in
inhaled air.
30. Dust from material such as paint containing
lead, some wood species, minerals and metal
may be harmful. Contact with or inhalation of
the dust may cause allergic reactions and/
or respiratory diseases to the operator or
bystanders.
Certain kinds of dust are classi ed as
carcinogenic such as oak and beech dust
especially in conjunction with additives
for wood conditioning (chromate, wood
preservative).
Notice sign for devices with a lter installed
from HEPA lter:
SPECIFIC SAFETY RULES AND
SYMBOLS
1. Do not block the vacuum cleaner opening
or blow port.
Blocking the vacuum cleaner opening will
cause an increase in the motor rotation speed
abnormally and might damage the vanes on
the inner section of the unit or cause injuries.
The motor might also overheat and cause a
re.
2. Do not topple the device or do not use it
on its side. May cause electric shock or
failures.
3. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine,
carbon tetrachloride, and alcohol may damage
and crack plastic parts. Do not wipe them with
such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dry
thoroughly.
4. Do not use the product if the device or the
battery terminals (battery mount) are deformed.
Installing the battery could cause a short circuit
that could result in smoke emission or ignition.
5. Keep the device's terminals (battery mount)
free of swarf and dust.
Prior to use, make sure that swarf and dust
have not collected in the area of the terminals.
During use, try to avoid swarf or dust on the
device from falling on the battery.
When suspending operation or after use, do
not leave the device in an area where it may be
exposed to falling swarf or dust.
Doing so could cause a short circuit that could
result in smoke emission or ignition.
6. De nitions for symbols used on this device
V .............volts
........... direct current
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result
from improper or unsafe use of battery
chargers. To avoid these risks, follow
these basic safety instructions:
5
English
READ ALL INSTRUCTIONS
1. This manual contains important safety and
operating instructions for battery charger
Model UC18YFSL.
2. Before using battery charger, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
3. Plug of battery charger must match the outlet.
Never modify the plug in any way.
Unmodi ed plugs and matching outlets will
reduce risk of electric shock.
4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the battery
charger.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk
of electric shock.
5. To reduce risk of injury, charge metabo HPT
rechargeable batteries. Other type of batteries
may burst causing personal injury and damage.
6. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of re, electric shock, or injury to
persons.
7. To reduce risk of damage to electric plug and
cord, pull by plug when disconnecting battery
charger.
8. Make sure cord is located so that it will not
be stepped on, tripped over, or otherwise
subjected to damage or stress.
9. An extension cord should not be used unless
absolutely necessary. Use of improper
extension cord could result in a risk of re and
electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug
on battery charger:
b. That extension cord is properly wired and
in good electrical condition; and
c. That wire size is large enough for AC
ampere rating of battery charger as
speci ed in Table 1.
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY
CHARGERS
AC Input Rating
Amperes* AWG Size of Cord
Equal
to or
greater
than
but less
than
Length of Cord, Feet
(Meter)
25
(7.5) 50
(15) 100
(30) 150
(45)
0 2 18 18 18 16
2 3 18 18 16 14
3 4 18 18 16 14
* If the input rating of a battery charger is given in
watts rather than in amperes, the corresponding
ampere rating is to be determined by dividing
the wattage rating by the voltage ratingfor
example:
1,250 watts = 10 amperes
125 volts
10. Do not operate battery charger with damaged
cord or plug-replace them immediately.
11. Do not operate battery charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way; take it to a quali ed
serviceman.
12. Do not disassemble battery charger; take it to a
quali ed serviceman when service or repair is
required. Incorrect reassembly may result in a
risk of electric shock or re.
13. To reduce risk of electric shock, unplug
charger from receptacle before attempting
any maintenance or cleaning. Removing the
battery will not reduce this risk.
6
English
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
BATTERY CHARGER
You must charge the battery before you can use the
vacuum cleaner. Before using the model UC18YFSL
battery charger, be sure to read all instructions and
cautionary statements on it, the battery and in this
manual.
WARNING
USE ONLY metabo HPT BATTERIES.
OTHER MODELS OF BATTERIES MAY
BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING
Improper use of the battery or battery
charger can lead to serious injury. To avoid
these injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is
damaged or is completely worn out. The
battery can explode in a re.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery
chargers air vents. Electric shock or damage
to the battery charger may result.
5. NEVER charge outdoors. Keep the battery
away from direct sunlight and use only where
there is low humidity and good ventilation.
6. NEVER charge when the temperature is below
32°F (0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for
the battery or the battery charger.
9. NEVER use a booster transformer when
charging.
10. NEVER use DC power to charge.
11. NEVER store the battery or battery charger in
places where the temperature may reach or
exceed 104°F (40°C) such as inside metal box
or car.
12. NEVER expose the battery or battery charger
to rain or wet conditions.
13. ALWAYS operate charger on standard
household electrical power (120 volts). Using
the charger on any other voltage may overheat
and damage the charger.
14. ALWAYS wait at least 15 minutes between
charges to avoid overheating the charger.
15. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 to 3 described below, when using
this product, even if you are pulling the switch, the
motor may stop. This is not the trouble but the result
of protection function.
1. When the battery power remaining runs out,
the motor stops.
In such case, charge it up immediately.
2. If the device is overloaded, the motor may stop.
In this case, release the switch of device and
eliminate causes of overloading. After that, you
can use it again.
3. If the battery is overheated under overload
work, the battery power may stop.
In this case, stop using the battery and let the
battery cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat
generation, smoke emission, explosion and ignition
beforehand, please be sure to heed the following
precautions.
1. Make sure that swarf and dust do not collect on
the battery.
During work make sure that swarf and dust do
not fall on the battery.
Make sure that any swarf and dust falling on
the power tool during work do not collect on the
battery.
Do not store an unused battery in a location
exposed to swarf and dust.
Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it
together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such
as a nail, strike with a hammer, step on, throw
or subject the battery to severe physical shock.
3. Do not use an apparently damaged or
deformed battery.
4. Do not use the battery for a purpose other than
those speci ed.
7
English
5. If the battery charging fails to complete even
when a speci ed recharging time has elapsed,
immediately stop further recharging.
6. Do not put or subject the battery to high
temperatures or high pressure such as into
a microwave oven, dryer, or high pressure
container.
7. Keep away from re immediately when leakage
or foul odor are detected.
8. Do not use in a location where strong static
electricity generates.
9. If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any
way appears abnormal during use, recharging
or storage, immediately remove it from the
equipment or battery charger, and stop use.
10. Do not immerse the battery or allow any uids
to ow inside. Conductive liquid ingress, such
as water, can cause damage resulting in re
or explosion. Store your battery in a cool, dry
place, away from combustible and ammable
items. Corrosive gas atmospheres must be
avoided.
CAUTION
1. If liquid leaking from the battery gets into your
eyes, do not rub your eyes and wash them well
with fresh clean water such as tap water and
contact a doctor immediately.
If left untreated, the liquid may cause eye-
problems.
2. If liquid leaks onto your skin or clothes, wash
well with clean water such as tap water
immediately.
There is a possibility that this can cause skin
irritation.
3. If you nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when
using the battery for the rst time, do not use
and return it to your supplier or vendor.
WARNING
If an electrically conductive foreign object
enters the terminals of the lithium ion battery,
a short-circuit may occur resulting in the risk of
re. Please observe the following matters when
storing the battery.
Do not place electrically conductive
cuttings, nails, steel wire, copper wire or
other wire in the storage case.
Either install the battery in the power tool
or store by securely pressing into the
battery cover until the ventilation holes
are concealed to prevent short-circuits
(See Fig. 3).
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please
observe the following precautions.
WARNING
Notify the transporting company that a package
contains a lithium-ion battery, inform the
company of its power output and follow the
instructions of the transportation company
when arranging transport.
Lithium-ion batteries that exceed a power
output of 100 Wh are considered to be in
the freight classi cation of Dangerous
Goods and will require special application
procedures.
For transportation abroad, you must
comply with international law and the rules
and regulations of the destination country.
Wh
Power Output
2 to 3 digit number
Fig. 1
8
English
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS VACUUM CLEANER!
FUNCTIONAL DESCRIPTION
NOTE
The information contained in this Instruction Manual is designed to assist you in the safe operation and
maintenance of the device.
NEVER operate, or attempt any maintenance on the device unless you have rst read and understood
all safety instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that di er from those on
your own device.
NAME OF PARTS
1. Cordless Vacuum Cleaner
Tank
Handle
Flexible
hose
Nozzle
“PressClean”
button
Shoulder strap
Switch
Clamp
Upper part
Nameplate
Suction opening
Extension wands
Blow port
Battery
Battery cover
Knob for battery cover
Crevice tool
Accessory
storage
Eyelet to attach a shoulder strap
Wide nozzle
Fig. 2
9
English
2. Battery
(optional accessories…sold separately) 3. Battery Charger
(optional accessories…sold separately)
Display panel
Latch
Ventilation holes
Terminals
Battery cover
<BSL1840M>
Fig. 3
Ventilation holes
Cord
Nameplate
Pilot lamp
Guide rail
<UC18YFSL>
Fig. 4
SPECIFICATIONS
1. Cordless Vacuum Cleaner
Model
Item RP18DA
Rated voltage 18 V
Motor DC motor
Filter type HEPA
Application Wet and Dry type
Suction work rate Boost (II) 80 W
Eco (I) 35 W
Operation time Boost (II) 13.2 min (BSL1840M)
Eco (I) 22.4 min (BSL1840M)
Max. vacuum 1.6 psi (11 kPa)
Max. air ow 63.5 cfm (1,800 L/min)
Flexible hose
diameter 1-3/16 (30 mm)
length 19-11/16 – 98-15/32
(500 – 2,500 mm)
Protection class IPX4
Details-Tank 1.6 gal (6.0 L)
Details-Dry 1.4 gal (5.1 L)
Details-Wet 0.9 gal (3.5 L)
Battery available for this tool Multi volt battery, BSL18 Series
Dimensions (W × D × H) 8.3 × 13.0 × 15.5
(210 mm × 330 mm × 393 mm)
Weight 10.4 lbs. (4.7 kg) (BSL1840M)
10.8 lbs. (4.9 kg) (BSL36A18)
11.2 lbs. (5.1 kg) (BSL36B18)
10
English
2. Battery Charger
Model UC18YFSL
Input power source Single phase: AC 120 V 60 Hz
Charging time
(At a temperature of 68°F (20°C)) BSL1840M : Approx. 60 min
Charging voltage DC 14.4–18 V
Charging current DC 3.5 A
Weight 1.1 lbs. (0.5 kg)
NOTE
The charging time may vary according to temperature and power source voltage.
ASSEMBLY AND OPERATION
APPLICATIONS
Vacuuming of dust, solid materials (broken
glass, nails etc.), with the exception of material
that is hotter than 60 °C
Vacuuming of liquids
UNPACKING
Carefully unpack the device.
Take out the accessories in the tank before
work.
REMOVAL AND INSTALLATION
METHOD OF BATTERY
How to install the battery.
Pull the knob for battery cover, and open the
battery cover.
Always insert it all the way until it locks in place
with a little click.
Battery cover
Knob for
battery cover
Open
Insert
Fig. 5
How to remove the battery.
Open the battery cover, and while pressing the
2 latches (one on each side), slide it and pull it
out.
Latch
Press
Pull out
Battery
Fig. 6
NOTE
Ensure that the battery cover is securely closed
after removing or installing the battery.
If any water or dust enters the body of the tool
or the terminals of the battery, a failure may
occur.
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the
following points.
The power source voltage is stated on the
nameplate.
The cord is not damaged.
11
English
WARNING
Do not charge at voltage higher than
indicated on the nameplate.
If charged at voltage higher than indicated
on the nameplate, the charger will burn
out.
<UC18YFSL>
1. Connect the chargers power cord to a
receptacle.
When the power cord is connected, the pilot
lamp will blink in red. (See Table 2)
WARNING
Do not use the electrical cord if damaged.
Have it repaired immediately.
2. Insert the battery to the battery charger.
Firmly Insert the battery into the battery
charger.
Battery
Pilot lamp
Guide rail
Fig. 7
3. Charging
When inserting a battery in the charger, the
pilot lamp will light up continuously in red.
When the battery becomes fully recharged, the
pilot lamp will blink in red. (See Table 2)
(1) Lamp indication
The indications of the pilot lamp will be as
shown in Table 2, according to the condition of
the battery charger or the battery.
Table 2: Indications of the pilot lamp
ON/OFF at 0.5 sec.
intervals Before charging *1
or
Charging complete
Lights continuously While charging
Lights for 1 sec. at
intervals of 0.5 sec. Overheat standby *2
ON/OFF at 0.1 sec.
intervals Charging impossible *3
NOTE
*1 If the red lamp continues to blink even after the
charger has been attached, check to con rm
that the battery has been fully inserted.
*2 Battery overheated. Unable to charge.
Although charging will start once the battery
has cooled down even when left in situ, the
best practice is to remove the battery and allow
it to cool down in a shaded, well-ventilated
location before charging.
*3 Malfunction in the battery or the charger
Fully insert the battery.
Check to con rm that no foreign matter is
stuck to the battery mount or terminals.
If there are no foreign objects, it is
probable that the battery or charger is
malfunctioning. Take it to your authorized
Service Center.
If the pilot lamp does not blink in red even
though the charger cord is connected to the
power, it indicates that the protection circuit of
the charger may be activated.
Remove the cord or plug from the power and
then connect it again after 5 minutes or so. If
this does not cause the pilot lamp to blink in
red, please take the charger to the metabo HPT
Authorized Service Center.
When the battery charger has been continuosly
used, the battery charger will be heated, thus
constituting the cause of the failures. Once the
charging has been completed, give 15 minutes
rest until the next charging.
12
English
(2) Regarding the temperature of the
rechargeable battery.
Table 3
Rechargeable
batteries Temperatures at which the battery
can be recharged
BSL1840M 32°F–122°F
(0°C50°C)
(3) Regarding recharging time (At 68°F (20°C))
Table 4 Charging time
Battery Charger: UC18YFSL
BSL1840M Approx. 60 min
NOTE
The recharging time may vary according to the
ambient temperature.
If charging takes a long time
Charging will take longer at extremely low
ambient temperatures. Charge the battery
in a warm location (such as indoors).
Do not block the air vent. Otherwise
the interior will overheat, reducing the
charger’s performance.
If the cooling fan is not operating, contact a
metabo HPT Authorized Service Center for
repairs.
4. Disconnect battery charger from the
receptacle.
CAUTION
Do not pull the plug out of the receptacle
by pulling on the cord.
Make sure to grasp the plug when removing
from receptacle to avoid damaging cord.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull
out the battery from the battery charger.
NOTE
Be sure to pull out the battery from the battery
charger after use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new
batteries and batteries that have not been
used for an extended period is not activated,
the electric discharge might be low when
using them the rst and second time.
This is a temporary phenomenon, and normal
time required for recharging will be restored by
recharging the batteries 2–3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool
becomes weaker, stop using the tool and
recharge its battery. If you continue to use
the tool and exhaust the electric current,
the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately
after use. If such a battery is recharged
immediately after use, its internal chemical
substance will deteriorate, and the battery
life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
PRIOR TO OPERATION
WARNING
Be sure to turn o the power switch and
remove the battery.
1. Attaching the accessory storage for extension
wands
The accessory storage and two Philip's head
screws are in the tank.
Attach the accessory storage to the vacuum
housing using the screws.
Screws
Accessory
storage
Fig. 8
2. Dust bag
(1) Switch o the device and open the clamps.
Remove the upper part of the device from the
tank.
(2) Insert a dust bag in the tank. Put the upper part
back on and close the clamps. Remove the
dust bag for wet vacuuming.
13
English
THE DEVICE
1. Switching on/o
Use the switch to turn the device On/O .
Level II: High suction power
recommended for pro led surface such as
carpets
Level I: Medium suction power
recommended for smooth surfaces
Level 0: O
Switch
Fig. 11
2. PressClean
To clean the lter using a strong air ow: Put the
switch in position II, cover the nozzle or suction
opening with the hand and press the button several
times (at least 3 times).
“PressClean” button
Suction opening
Fig. 12
Dust bag
Tank
Fig. 9
3. Shoulder strap
If required, hook the shoulder strap into both
eyelets left and right of the device. Set the
shoulder strap to the desired length.
OK
Eyelets
Shoulder strap
Fig. 10
Carrying:
The device must be carried only with the
shoulder strap provided with the device.
The device must NOT be carried with the shoulder
strap around your neck.
14
English
USE
1. This device is suitable for dry and wet
applications
The device must not be switched on without lter in
place.
Filter screw
Filter holder
Filter
Electrodes of stainless steel
Fig. 13
Wet vacuuming
Remove the dust bag for wet vacuuming.
The device switches o automatically once the
maximum water level has been reached.
The device is not switched o when the tank is
full for non-conductive liquids (such as
emulsion drilling uids, oils and greases).
The ll level must be monitored continuously and the
tank must be emptied promptly.
NOTE
If water is suctioned quickly, then you will not be
able to suction as much as if water is suctioned
slowly.
The lter will get wet when suctioning water.
Ensure that it has su cient time to dry and
that all components are completely dry before
using the device for dry vacuuming.
If the water switch-o does not work and uid
is suctioned into the motor so that water comes
out of the device, stop the device. Allow the
device to dry su ciently.
After wet vacuuming: clean the lter after drying it
completely with the lter cleaning element. Clean the
electrodes of stainless steel with steel brush if any
contaminations on them. Clean the tank with a moist
cloth and dry it o .
Dry Vacuuming
Vacuum only with dry lter, device and accessories.
If the cartridge is damp, dust may stick and form a
crust.
For dry vacuuming dust bags are recommended to
use.
Using as a blower
Use with the exible hose inserted into the blow port.
2. Transport
Store the exible hose on the housing.
The upper part must be securely sealed to the tank -
check that the clamps are closed.
Set the switch to position “0”.
3. Using accessories
When using the wide nozzles and/or tube, we
recommend mounting the nozzle between the
exible hose and the wide nozzles/extension wand
in use.
4. Remaining battery indicator
You can check the battery’s remaining capacity by
pressing the remaining battery indicator switch to
light the indicator lamp. (Table 5)
It is best to use the remaining battery indicator as
a guide since there are slight di erences such as
ambient temperature and the condition of the battery.
Also, the remaining battery indicator may vary from
those equipped to a tool or charger.
Display panel
Remaining battery
indicator lamp Remaining battery
indicator switch
Fig. 14
15
English
Table 5
Lights ;
The battery remaining power is
over 75%.
Lights ;
The battery remaining power is
50%75%.
Lights ;
The battery remaining power is
25%–50%.
Lights ;
The battery remaining power is
less than 25%.
Blinks ;
The battery remaining power is
nearly empty. Recharge the battery
soonest possible.
Blinks ;
Output suspended due to high
temperature.
Remove the battery from the tool and
allow it to fully cool down.
Blinks ;
Output suspended due to failure or
malfunction. The problem may be
the battery so please contact your
dealer.
As the remaining battery indicator shows somewhat
di erently depending on ambient temperature and
battery characteristics, read it as a reference.
CAUTION
Do not give a strong shock to the switch
panel or break it. It may lead to a trouble.
CLEANING
1. General Cleaning Instructions
WARNING
Turn o the power switch and remove the
battery before cleaning the device.
Clean the tank and accessories with water. Wipe the
upper part with a damp cloth.
CAUTION
This device contains dust that is harmful
to health. Discharge and maintenance
operations (including disposal of the dust
collection tanks) must only be carried
out by quali ed specialists wearing
appropriate protective clothing and
equipment.
Emptying the Tank
For dust class only permitted for dusts with
occupational exposure limits > 1mg/m3.
(1) Set the switch to position “0
(2) Remove the battery
(3) Open the clamps. Remove the upper part of
the device from the tank.
(4) Tip out the tank.
Disposing of the Dust Bag
(1) Set the switch to position “0
(2) Remove the battery.
(3) Open the clamps. Remove the upper part of
the device from the tank.
(4) Carefully remove the dust bag.
(5) Be careful with dust during disposal!
(6) Dispose of the vacuumed material in
accordance with legal regulations.
Clean the lter via PressClean
– Clean the lter according to “2. PressClean” on
page 13.
Clean the lter manually
– Remove the lter according to “2. Replacing
the lter” on page 16.
Occasionally tap the lter to remove any dust
that has gathered on it. If the lter is very dirty,
you can clean it with water and a soft brush.
Allow to lter to dry properly afterwards.
16
English
MAINTENANCE AND INSPECTION
WARNING
For inspection and maintenance, be sure
to turn o the power switch and remove
the battery.
Do not work with wet hands. May cause
electric shock or injuries.
1. General instructions
Clean the device (see “CLEANING” on
page 15).
For maintenance by the user, the vacuum cleaner
must be taken apart, cleaned and maintained, to the
extent possible, without endangering maintenance
sta or other people.
Preventive measures
Appropriate preventive measures include: cleaning
the device before disassembly; providing local
ltered forced ventilation where the vacuum cleaner
is disassembled; cleaning of the maintenance area
and providing suitable personal protective clothing
and equipment.
When carrying out maintenance or repairs, it is
essential to dispose of any contaminated objects
that cannot be adequately cleaned. These objects
must be disposed of using impermeable bags and
in accordance with the applicable regulations for
removing such waste.
2. Replacing the lter
(1) Clean the lter again before replacement
(“2. PressClean” on page 13)
(2) Set the switch to position “0
Remove battery.
(3) Open the clamps. Remove the upper part of
the device from the tank.
(4) Unscrew the screws on the bottom of the upper
part (Fig. 2 on page 8) so that the lter and lter
holder can be removed.
(5) Seal the removed lter immediately in a dust-
tight plastic bag and dispose of it in accordance
with regulations.
(6) Insert a new lter into the lter holder and use
the screw to attach it in the vacuum once again.
Ensure proper and secure position.
3. Inspection of terminals (device and battery)
Check to make sure that swarf and dust have
not collected on the terminals.
On occasion check prior, during and after
operation.
CAUTION
Remove any swarf or dust which may have
collected on the terminals.
Failure to do so may result in malfunction.
4. Storage
Storing in a place below 104°F (40°C) and out
of the reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been
fully charged before storing them.
Prolonged storage (3 months or more) of
batteries with a low charge may result in
performance deterioration, signi cantly
reducing battery usage time or rendering the
batteries incapable of holding a charge.
However, signi cantly reduced battery usage
time may be recovered by repeatedly charging
and using the batteries two to ve times.
If the battery usage time is extremely short
despite repeated charging and use, consider
the batteries dead and purchase new batteries.
5. Service and repairs
All quality devices will eventually require
servicing or replacement of parts because
of wear from normal use. To assure that only
authorized replacement parts will be used,
all service and repairs must be performed
by a metabo HPT AUTHORIZED SERVICE
CENTER, ONLY.
Important notice on the batteries for the
metabo HPT cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when
used with batteries other than these designated
by us, or when the battery is disassembled and
modi ed (such as disassembly and replacement
of cells or other internal parts).
17
English
TROUBLESHOOTING GUIDE
WARNING
To avoid injury from an accidental start, turn the switch OFF and remove the plug from the
power source or remove the battery from the main body before making any adjustments.
All electrical or mechanical repairs should be done only by quali ed service technicians.
Contact metabo HPT Authorized Service Center.
Reduction in suction power:
See the instructions in the “CLEANING” on page 15.
Is the lter dirty? - clean.
Dust bag full? - replace.
Tank full? - empty.
Nozzle, tubes or hose blocked?- clean.
Is the battery weak? - Charge/replace battery.
Device will not start:
Is the battery empty? - Charge/replace battery.
Water level detection active - empty tank, set
switch to “0” and restart the vacuum at level “I
or “II.
Particles are discharged at the outlet:
Is the lter defective? - Check the lter and
replace if required (“2. Replacing the lteron
page 16).
The device has shut down by itself:
Causes and remedies:
Battery almost at: (the electronics prevent
the battery form discharging totally and avoid
damage). If the capacity indicator ashes
after pressing the battery button to display the
battery capacity, then the battery is almost
empty and must be recharged.
Battery is not inserted properly: Check and
correct.
Long continuous overloading of the device will
activate the temperature cut-out.
Leave the device or battery to cool.
Water level detection active - empty tank, set
switch to “0” and restart the vacuum at level “I
or “II.
18
English
ACCESSORIES
WARNING
ALWAYS use Only authorized metabo HPT replacement parts and accessories. Never use
replacement parts or accessories which are not intended for use with this device. Contact
metabo HPT if you are not sure whether it is safe to use a particular replacement part or
accessory with your device.
The use of any other attachment or accessory can be dangerous and could cause injury or
mechanical damage.
NOTE
Accessories are subject to change without any obligation on the part of the metabo HPT.
STANDARD ACCESSORIES
RP18DA
(NN)
Flexible hose (Code No. 380953) ........................................................... 1
Wide nozzle (Code No. 380951) ............................................................. 1
Crevice tool (Code No. 380952) ............................................................. 1
Pipe set (Code No. 380955) ................................................................... 1
Accessory storage (Code No. 380950) .................................................. 1
Shoulder strap (Code No. 380949) ......................................................... 1
HEPA Filter (Code No. 380971) .............................................................. 1
Battery, battery charger and battery cover are not contained.
OPTIONAL ACCESSORIES (sold separately)
(1) Battery (BSL1840M)
(2) Battery charger (UC18YFSL)
(3) Dust bag (5 pcs.) (Code No. 380954)
NOTE
Speci cations are subject to change without any obligation on the part of the metabo HPT.
INFORMATIONS IMPORTANTES DE SÉCURITÉ
Lisez et assimilez toutes les précautions de sécurité, les avertissements et les instructions d’utilisation du
Mode d’emploi avant d’utiliser ou d’entretenir cet aspirateur.
La plupart des accidents qui résultent de l’utilisation et de l’entretien de l’aspirateur sont causés par un non
respect des règles ou des précautions de sécurité basiques. Un accident peut la plupart du temps être évité si
l’on reconnaît une situation de danger potentiel avant qu’elle ne se produise, et en observant les procédures
de sécurité appropriées.
Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode
d’emploi et dans les sections qui contiennent les instructions de fonctionnement et dentretien.
Les dangers qui doivent être évités pour prévenir des blessures corporelles ou des dommages de l’appareil
sont identi és par des AVERTISSEMENTS sur l’aspirateur et dans ce Manuel d’instructions.
N’utilisez JAMAIS cet aspirateur d’une manière qui n’a pas été spéci quement recommandée par
metabo HPT.
SIGNIFICATION DES MOTS D’AVERTISSEMENT
AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient
entraîner la mort ou de sérieuses blessures.
PRÉCAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent
entraîner de mineures et légères blessures ou endommager la machine.
REMARQUE met en relief des informations essentielles.
UTILISATION CONFORME À LUSAGE
Cet aspirateur est conçu pour laspiration de la poussière et de corps solides (éclats de verre, clous, etc.),
mais il ne peut pas aspirer des matériaux dont la température dépasse 60 °C.
Laspirateur convient à l’aspiration de liquides.
Cet appareil ne doit pas être utilisé par des personnes présentant des capacités physiques, sensorielles ou
mentales réduites ou manquant d’expérience et/ou de connaissances, sauf si elles sont surveillées par une
personne responsable de leur sécurité ou qu’elles reçoivent des instructions sur l’utilisation de l’appareil.
Veuillez respecter les dispositions spéci ques au pays, ainsi que les indications du fabricant des matériaux.
Cet appareil convient à un usage professionnel, par exemple dans les hôtels, les écoles, les hôpitaux, les
usines, les magasins et les bureaux.
Il est interdit daspirer des poussières contenant de l’amiante.
Il est interdit daspirer des poussières in ammables.
Il est interdit d’aspirer des solvants in ammables ou explosifs, des matières imprégnées de solvants, des
poussières explosives, des solutions ou des matières dont la température est supérieure à 60 °C. Cela
risque de provoquer une explosion et un incendie ! Lappareil ne doit pas être utilisé à proximité de gaz et de
substances in ammables.
L’utilisateur est entièrement responsable de tous les dommages résultant d’une utilisation non conforme.
Il est impératif de respecter les consignes générales de prévention contre les accidents ainsi que les
consignes de sécurité ci-jointes.
Laspirateur convient à l’aspiration de poussière sèche, non in ammable et de poussières
de bois. Le degré de rétention du ltre HEPA est de 99,95 %.
19
Français
Pour réduire le risque d’incendie, de choc
électrique ou de blessure:
CONSIGNES GÉNÉRALES DE
SÉCURITÉ
1. Avant d’utiliser l’appareil, lisez attentivement
et entièrement les consignes de sécurité ainsi
que le mode d’emploi fournis. Conservez toute
la documentation jointe pour des références
futures et, si vous transmettez votre appareil,
joignez-y la documentation.
2. Avant toute utilisation, l’utilisateur doit
recevoir les informations, instructions et
formations nécessaires à l’utilisation de
l’appareil et des substances pour lesquelles
l’appareil peut être utilisé, ainsi que les
consignes de sécurité concernant l’élimination
du matériel acheté.
CONSIGNES DE SÉCURITÉ
PARTICULIÈRES
1. Pour des raisons de sécurité et a n de
protéger lappareil, respectez les
passages de texte marqués de ce symbole !
2. Ne jamais laisser les enfants utiliser lappareil.
Les enfants doivent être surveillés pour
s’assurer qu’ils ne jouent pas avec l’appareil.
3. Attention ! Utiliser exclusivement les
accessoires fournis avec l’appareil ou indiqués
dans le mode d’emploi. L’utilisation d’autres
accessoires risque da ecter la sécurité.
4. Il est interdit d’exécuter d’autres travaux que
ceux décrits dans la présente notice.
5. Nous déclinons toute responsabilité pour les
éventuels dommages en cas d’utilisation ou de
réparation non conforme.
6. Ne pas mettre les appareils et les accessoires
en marche lorsque :
- l’appareil présente des dommages visibles
(fêlures/cassures),
- la batterie est défectueuse,
- on soupçonne la présence d’un défaut
invisible (après une chute).
7. Uniquement utiliser l’appareil avec couvercle
de batterie fermé. Gardez le couvercle de
la batterie fermé, même si la batterie n’est
pas insérée. Après avoir fermé le couvercle
de la batterie, véri ez bien que le bouton du
couvercle de la batterie est engagé.
8. Ne pas diriger la buse, le exible ou le tube
vers des personnes ou des animaux.
9. Ne jamais monter ni s’asseoir sur l’appareil.
10. Toujours poser le exible de manière à ce que
personne ne risque de trébucher dessus.
11. Ne pas laisser lappareil sans surveillance.
12. Laspirateur ne peut pas être utilisé ou rangé à
l’extérieur.
13. ATTENTION - L’utilisation et le remisage de cet
appareil doit se faire uniquement en intérieur.
14. Les acides, l’acétone et les solvants peuvent
attaquer les pièces de l’appareil.
15. Éteindre l’appareil et retirer la batterie
avant chaque entretien ou nettoyage de
l’appareil.
16. Les appareils à jet de vapeur et les nettoyeurs
haute pression ne peuvent pas être utilisés
pour nettoyer l’aspirateur.
17. Si l’appareil n’est pas nettoyé pendant une
longue période, des moisissures peuvent
se développer, surtout s’il est utilisé dans
des endroits où sont traitées des denrées
alimentaires : toujours nettoyer et désinfecter
l’appareil immédiatement après utilisation.
18. Ne jamais ouvrir l’appareil à l’extérieur par
temps de pluie ou en cas d’orage.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, les précautions de base doivent toujours être suivies, y compris
les suivantes :
LISEZ TOUTES LES INSTRUCTIONS AVANT
D’UTILISER (CET APPAREIL)
AVERTISSEMENT
20
Français
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Hikoki RP18DA Manuel utilisateur

Catégorie
Aspirateurs
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues