Hikoki M3612DA 36V Cordless Multi-Volt Brushless Router Manuel utilisateur

M 3612DA

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Οδηγίες χειρισμού

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

Pokyny na manipuláciu

Инструкция за експлоатация

Uputstvo za rukovanje

Upute za rukovanje

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

hu

cs

tr

ro

sl

sk

bg

sr

hr

el

pl

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

el

pl

hu

cs

tr

ro

sl

sk

bg

sr

hr

2

1

2

3 4

3

5 6

7 8

9

(a) (b)

10

4

11 12

a

13 14

15 16

5

17 18

(a) (b)

19 20

21 22

6

23 24

25 26

27

ab

7

28 29

8

English

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking up

or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power toolʼs operation. If

damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent from

those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and

speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-skid

safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

(Original instructions)

9

English

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by the

manufacturer.

A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another

battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

e) Do not use a battery pack or tool that is damaged

or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁ ed in the instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

CORDLESS ROUTER SAFETY

WARNINGS

1. Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could

give the operator an electric shock.

2. Use clamps or another practical way to secure and

support the workpiece to a stable platform.

Holding the work by your hand or against the body

leaves it unstable and may lead to loss of control.

3. Single-hand operation is unstable and dangerous.

Ensure that both handles are gripped ﬁ rmly during

operation.

4. The bit is very hot immediately after operation. Avoid

bare hand contact with the bit for any reason.

5. Use bits of the correct shank diameter suitable for the

speed of the tool.

ADDITIONAL SAFETY WARNINGS

1. Always charge the battery at a temperature of 0°C–40°C.

A temperature of less than 0°C will result in over charging

which is dangerous. The battery cannot be charged at a

temperature higher than 40°C.

The most suitable temperature for charging is that of

20°C–25°C.

2. Do not use the charger continuously.

When one charging is completed, leave the charger for

about 15 minutes before the next charging of battery.

3. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

4. Never disassemble the rechargeable battery and

charger.

5. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

6. Do not dispose of the battery in ﬁ re. If the battery is burnt,

it may explode.

7. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

8. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or inﬂ ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

9. When using this unit continuously, the unit may overheat,

leading to damage in the motor and switch. Therefore,

whenever the housing becomes hot, give the tool a

break for a while.

10. If the machine is used continuously at low speed, an

extra load is applied to the motor which can result in

motor seizure. Always operate the power tool so that

the blade is not caught by the material during operation.

Always adjust the blade speed to enable smooth cutting.

11. Preparing and checking the work environment. Make

sure that the work site meets all the conditions laid forth

in the precautions.

12. Make sure that the battery is installed ﬁ rmly. If it is at all

loose it could come oﬀ and cause an accident.

13. Handle the bits very carefully.

14. Check the bit carefully for cracks or damage before

operation. Replace cracked or damaged bit immediately.

15. Avoid cutting nails. Inspect for and remove all nails from

the workpiece before operation.

16. Hold the tool ﬁ rmly with both hands.

17. Make sure the bit is not contacting the workpiece before

the switch is turned on.

18. Before using the tool on an actual workpiece, let it run

for a while. Watch for vibration or wobbling that could

indicate improperly installed bit.

19. Be careful of the bit rotating direction and the feed

direction.

20. Always switch oﬀ and wait for the bit to come to a

complete stop before removing the tool from workpiece.

21. After changing the bits or making any adjustments, make

sure the collet chuck and any other adjustment devices

are securely tightened.

Loose adjustment device can unexpectedly shift,

causing loss of control, loose rotating components will

be violently thrown.

22. Do not expose directly your eye to the light by looking

into the light.

If your eye is continuously exposed to the light, your eye

will be hurt.

23. Never touch moving parts.

Never place your hands, ﬁ ngers or other body parts near

the tool’s moving parts.

24. NEVER leave tool running unattended. Turn power oﬀ .

Don’t leave tool until it comes to a complete stop.

10

English

25. The power tool is equipped with a temperature

protection circuit to protect the motor. Continuous work

may cause the temperature of the unit to rise, activating

the temperature protection circuit and automatically

stopping operation. If this happens, allow the power tool

to cool before resuming use.

26. Do not give a strong shock to the switch panel or break it.

It may lead to a trouble.

27. Do not use the product if the tool or the battery terminals

(battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

28. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○ Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○ During use, try to avoid swarf or dust on the tool from

falling on the battery.

○ When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result in

smoke emission or ignition.

29. Always use the tool and battery at temperatures between

-5°C and 40°C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately stop

further recharging.

8. Do not put or subject the battery to high temperatures or

high pressure such as into a microwave oven, dryer, or

high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible and

ﬂ ammable items. Corrosive gas atmospheres must be

avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the ﬁ rst time, do not use and return it to your

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium

ion battery, the battery may be shorted, causing ﬁ re. When

storing the lithium ion battery, obey surely the rules of

following contents.

○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing

until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe the

following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output of

100 Wh are considered to be in the freight classiﬁ cation

of Dangerous Goods and will require special application

procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

○ If the BSL36B18 is installed in the power tool, the power

output will exceed 100 Wh and the unit will be classiﬁ ed

as Dangerous Goods for freight classiﬁ cation.

Wh

Power Output

2 to 3 digit number

11

English

USB DEVICE CONNECTION

PRECAUTIONS (UC18YSL3)

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the USB

device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○ Prior to use, check the connecting USB cable for any

defect or damage.

Using a defective or damaged USB cable can cause

smoke emission or ignition.

○ When the product is not being used, cover the USB port

with the rubber cover.

Buildup of dust etc. in the USB port can cause smoke

emission or ignition.

NOTE

○ There may be an occasional pause during USB

recharging.

○ When a USB device is not being charged, remove the

USB device from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

○ It may not be possible to charge some USB devices,

depending on the type of device.

○ Charging a USB device from an electrical outlet

(Fig. 27-a)

○ Charging a USB device and battery from an electrical

outlet (Fig. 27-b)

○ How to recharge USB device (Fig. 28)

○ When charging of USB device is completed (Fig. 29)

NAMES OF PARTS (Fig. 1–Fig. 29)

Battery Name plate

Motor Handle

Head cover Switch trigger

Dial Lock lever

Stopper pole LED light

Depth indicator Threaded column

Wing bolt Latch

Lock pin Charge indicator lamp

Stopper block Bit

Base 23 mm Wrench

Sub base Loosen

Collet chuck Tighten

Straight guide Scale

Wing bolt (A) Nuts

Lock spring Cut depth setting

screw

ON/OFF Lock button Nut

Template guide Rotation of bit

Screw Router feed

Template

Inner peripheral cutting

(Clockwise)

Guide bar

Outer peripheral cutting

(Counterclockwise)

Bar holder Trimmer guide

Feed screw Roller

Wing bolt (B) Dust collector

Separate Knob nut

Work piece

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

M3612DA: Cordless Router

To reduce the risk of injury, user must read

instruction manual.

Always wear eye protection.

Always wear hearing protection.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive

2012/19/EU on waste electrical and electronic

equipment and its implementation in

accordance with national law, electric tools

that have reached the end of their life must

be collected separately and returned to an

environmentally compatible recycling facility.

Direct current

V Rated voltage

n0No-load speed

Disconnect the battery

Switching ON

Switching OFF

Lock

Switch locks to the “ON” position

Warning

12

English

Prohibited action

Battery

Lights ;

The battery remaining power is over 75%

Lights ;

The battery remaining power is 50%–75%.

Lights ;

The battery remaining power is 25%–50%.

Lights ;

The battery remaining power is less than 25%

Blinks ;

The battery remaining power is nearly empty.

Recharge the battery soonest possible.

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow it to

fully cool down.

Blinks ;

Output suspended due to failure or malfunction.

The problem may be the battery so please

contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed on page 272.

Standard accessories are subject to change without notice.

APPLICATIONS

○ Woodworking jobs centered on grooving and

chamfering.

SPECIFICATIONS

1. Power tool

Model M3612DA

Voltage 36 V

No-Load Speed 11000–25000 min–1

Collet Chuck Capacity 12 mm, 8 mm, 6 mm or

1/2", 1/4"

Main Body Stroke 50 mm

Battery available for this tool* Multi volt battery

Weight** 3.8 kg (BSL36A18)

4.1 kg (BSL36B18)

* Existing batteries (BSL3660/3620/3626, BSL18xx

series, etc.) cannot be used with this tool.

** According to EPTA-Procedure 01/2014

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

2. Battery

Model BSL36A18 BSL36B18

Voltage 36 V / 18 V (Automatic Switching*)

Battery capacity 2.5 Ah / 5.0 Ah 4.0 Ah / 8.0 Ah

(Automatic Switching*)

Available cordless

products** Multi volt series, 18 V product

Available charger Sliding charger for lithium ion

batteries

* The tool itself will automatically switch over.

** Please see our general catalogue for details.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.

When connecting the plug of the charger to a receptacle,

the charge indicator lamp will blink in red (At 1- second

intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 3 (on page 2).

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the charge

indicator lamp will light up in green. (See Table 1)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be as

shown in Table 1, according to the condition of the

charger or the rechargeable battery.

13

English

Table 1

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging Blinks

(RED)

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds) Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light for

1 second. (oﬀ for 1 second) Battery capacity at less than 50%

Blinks

(BLUE)

Lights for 1 second. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds) Battery capacity at less than 80%

Lights

(BLUE) Lights continuously Battery capacity at more than 80%

Charging

complete Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby Blinks

(RED)

Lights for 0.3 seconds. Does not light for

0.3 seconds. (oﬀ for 0.3 seconds) Battery overheated. Unable to

charge. (Charging will commence

when battery cools)

Charging

impossible Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

(2) Regarding the temperatures and charging time of the rechargeable battery

The temperatures and charging time will become as shown in Table 2.

Table 2

Charger UC18YSL3

Battery

Type of battery Li-ion

Temperatures at which the

battery can be recharged 0°C–50°C

Charging voltage V 14.4 18

Charging time,

approx. (At 20°C)

BSL14xx series BSL18xx series Multi volt

series

(4 cells) (8 cells) (5 cells) (10 cells) (10 cells)

min

BSL1415S : 15

BSL1415 : 15

BSL1415X : 15

BSL1420 : 20

BSL1425 : 25

BSL1430C : 30

BSL1430 : 20

BSL1440 : 26

BSL1450 : 32

BSL1460 : 38

BSL1815S : 15

BSL1815 : 15

BSL1815X : 15

BSL1820 : 20

BSL1825 : 25

BSL1830C : 30

BSL1850C : 32

BSL1830 : 20

BSL1840 : 26

BSL1850 : 32

BSL1860 : 38

BSL36A18 : 32

BSL36B18 : 52

USB Charging voltage V 5

Charging current A 2

NOTE

The recharging time may vary according to the ambient temperature and power source voltage.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

14

English

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because

it has been left for a long time in a location subject to

direct sunlight or because the battery has just been

used, the charge indicator lamp of the charger lights

for 0.3 seconds, does not light for 0.3 seconds (oﬀ for

0.3 seconds). In such a case, ﬁ rst let the battery cool,

then start charging.

○ When the charge indicator lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about

3 seconds to conﬁ rm that the battery being charged with

UC18YSL3 is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery

is reinserted within 3 seconds, the battery may not be

properly charged.

PRIOR TO OPERATION

WARNING

Pull out battery before carrying out any adjustment,

servicing or maintenance.

When ﬁ nished with a job, pull out the battery.

1. Power switch

Ensure that the switch is in the OFF position. If the battery

installed to power tool while the switch is in the ON

position, the power tool will start operating immediately,

which could cause a serious accident.

2. Removing and inserting the battery (Fig. 2)

3. Remaining battery indicator (Fig. 4)

INSTALLING AND REMOVING BITS

WARNING

Be sure to switch power OFF and pull out the battery to

avoid serious trouble.

1. Installing bits

(1) Loosen the lock lever, raise the tool to the maximum

stroke position and return the lock lever to the tightening

position.

(2) Clean and insert shank of bit into the collet chuck until

shank bottoms, then back it out approximately 2 mm.

(3) With the bit inserted and pressing the lock pin holding

the shaft, use the 23 mm wrench to ﬁ rmly tighten the

collet chunk in a clockwise direction (viewed from under

the router). (Fig. 5)

CAUTION

○ Ensure that the collet chuck is ﬁ rmly tightened after

inserting a bit. Failure to do so will result in damage to

the collet chuck.

○ Ensure that the lock pin is not inserted into the shaft after

tightening the collet chuck. Failure to do so will result in

damage to the collet chuck, lock pin and shaft.

(4) When using the 8 mm or 1/4" diameter shank bit, replace

the equipped collet chuck with the one for 8 mm or 1/4"

diameter shank bit which is provided as the standard

accessory.

(5) Be sure to use a chuck sleeve when using a 6 mm bit

with a collet chuck capacity of 12 mm. First insert the

chuck sleeve deeply in the collet chuck, then insert the

bit in the chuck sleeve. Tighten the collet chuck ﬁ rmly as

in step (1) and (2).

2. Removing bits

(1) Loosen the lock lever, raise the tool to the maximum

stroke position and return the lock lever to the tightening

position.

(2) Pressing the lock pin, loosen the collet chuck with the

included 23 mm wrench to pull out the bit. (Fig. 6)

CAUTION

Ensure that the lock pin is not inserted into the shaft after

tightening the collet chuck. Failure to do so will result in

damage to the collet chuck, lock pin and shaft.

HOW TO USE THE ROUTER

1. Adjusting depth of cut (Fig. 7)

(1) Use stopper pole to adjust depth of cut.

Place the tool on a ﬂ at wood surface.

Turn the stopper block so that section to which the cutting

depth setting screw on a stopper block is not attached

comes to the bottom of the stopper pole. Loosen pole

lock knob allowing the stopper pole to contact with

stopper block.

Loosen the lock lever and press the tool body until the bit

just touches the ﬂ at surface. Tighten the lock lever at this

point. (Fig. 8)

Tighten pole lock knob. Align the depth indicator with the

“0” graduation of scale.

Loosen pole lock knob, and raise until indicator aligns

with the graduation representing the desired cutting

depth. Tighten pole lock knob.

Loosen the lock lever and press the tool body down until

the stopper block to obtain the desired cutting depth.

(2) As shown in Fig. 9 (a), loosening the two nuts on the

threaded column and moving then down will allow you to

move down to the end position of the bit when the lock

lever is loosened. This is helpful when moving the router

to align the bit with the cutting position.

As shown in Fig. 9 (b), tighten the upper and lower nuts

to secure the cutting depth.

(3) When you are not using the scale to set the cutting depth,

push up the stopper pole so that it is not in the way.

2. Stopper block (Fig. 10)

The 2 cut-depth setting screws attached to the stopper

block can be adjusted to simultaneously set 3 diﬀ erent

cutting depth. Use a wrench to tighten the nuts so that

the cut-depth setting screws do not come loose at this

time.

3. Guiding the router

WARNING

Be sure to switch power OFF and pull out the battery to

avoid serious trouble.

(1) Template Guide (Standard Accessory)

Use the template guide when employing a template

for producing a large quantity of identiﬁ cally shaped

products.

As shown in Fig. 11, secure the template guide to the

base of the router with two accessory screws. At this

time, ensure that the projection side of the template

guide is facing the bottom surface of the base of the

router.

15

English

A template is a proﬁ ling mold made of plywood or thin

lumber.

When making a template, pay particular attention to the

matters described bellow and illustrated in Fig. 12.

When using the router along the interior plane of the

template, the dimensions of the ﬁ nished product will be

less than the dimensions of the template by a amount

equal to dimension “A”, the diﬀ erence between the

radius of the template guide and the radius of the bit. The

reverse is true when using the router along the exterior of

the template.

Secure the template to the workpiece. Feed the router

in the manner that the template guide moves along the

template as shown in Fig. 13.

(2) Straight guide (Standard accessory) (Fig. 14)

Use straight guide for chamfering and groove cutting

along the materials side.

Insert the guide bar into the hole in the bar holder, then

lightly tighten the 2 wing bolts (A) on top of the bar

holder.

Insert the guide bar into the hole in the base, then ﬁ rmly

tighten the wing bolt (A).

Make minute adjustments of the dimensions between

the bit and the guide surface with the feed screw, then

ﬁ rmly tighten the 2 wing bolts (A) on top of the bar holder

and the wing bolt (B) that secures the straight guide.

As shown in Fig. 15, securely attach the bottom of the

base to processed surface of the materials. Feed the

router while keeping the guide plane on the surface of

the materials.

4. Switch operation

This product is equipped with an ON/OFF Lock button

to prevent any inadvertent switch trigger operation. To

activate the tool, press down on the ON/OFF Lock button

and draw the switch trigger. (Fig. 16)

When the switch trigger is fully drawn, a further press

of the ON/OFF Lock button will lock the switch trigger

in place, allowing the release of the switch trigger for

continued operation. (Fig. 17 (a))

The switch trigger will not be locked if the ON/OFF Lock

button is released before the switch trigger is fully drawn,

making it possible to operate the tool with a press of the

switch trigger.

To unlock the switch trigger, draw the switch trigger

once again to release the ON/OFF Lock button and

discontinue operation. (Fig. 17 (b))

Prior to using the tool, make sure that the ON/OFF Lock

button and the switch trigger are operating properly.

5. How to use the LED light (Fig. 18)

The LED light will light the area at the tip of the tool when

the switch is “ON”.

The LED light will automatically power oﬀ 10 seconds

after the switch is released.

6. Adjusting the rotation speed

The M3612DA has an electronic control system that

allows rpm changes.

As shown in Fig. 19, dial position “1” is for minimum

speed, and position “6” for maximum speed.

7. Cutting

CAUTION

○ Wear eye protection when operating this tool.

○ Keep your hands, face and other body parts away from

the bits and any other rotating parts, while operating the

tool.

NOTE

○ Do not press the lock pin while the motor is rotating.

Also, do not switch the tool on while pressing the lock

pin.

Doing so may damage the lock pin and/or shaft as well

as result in injury.

○ Please limit the cutting depth of a single cut to under

20 mm.

○ When cutting a deep groove, repeat the cut 2 or 3 times.

Deep cutting operations can make the tool diﬃ cult

to control and may overload the motor, resulting in

malfunction.

○ Moving the tool forward fast may cause a poor quality

of cut, or damage to the bit or motor. Moving the tool

forward too slowly may burn and mar the cut.

The proper feed rate will depend on the bit size, the kind

of workpiece and depth of cut. Before beginning the cut

on the actual workpiece, it is advisable to make a sample

cut on a piece of scrap lumber. This will show exactly

how the cut will look as well as enable you to check

dimensions.

○ Abnormalities and overloads will trigger the overload

protector, and stop operation. Remove the load

immediately, and turn the power oﬀ , then on. The

rotation speed should return to normal.

(1) As shown in Fig. 20, remove the bit from the work pieces

and press the switch lever up to the ON position. Do

not start cutting operation until the bit has reached full

rotating speed.

(2) The bit rotates clockwise (arrow direction indicated on

the base). To obtain maximum cutting eﬀ ectiveness,

feed the router in conformance with the feed directions

shown in Fig. 21.

8. Trimmer Guide (Optional accessory) (Fig. 22)

Use the trimmer guide for trimming or chamfering. Attach

the trimmer guide to the bar holder as shown in Fig. 23.

After aligning the roller to the appropriate position,

tighten the two wing bolts (A) and the other two wing

bolts (B). Use as shown in Fig. 24.

9. Dust Collector Set (Standard accessory)

Connect the dust collector set cleaner to collect dust.

(1) Mounting the dust collector.

Use a screwdriver to attach the two screws to the base.

(Fig. 25)

Align the holes on the dust collector with the two screws

and attach the dust collector.

Tighten the two knob nuts.

Connect the cleaner to the dust collector. (Fig. 26)

(2) Dismounting the dust collector.

Use a screwdriver to loosen the two screws.

LED LIGHT WARNING SIGNALS

(Fig. 30)

This product features functions that are designed to protect

the tool itself as well as the battery. When any of the

safeguard functions are triggered, any of the LED light will

blink as described in Table 3.

In this case, follow the instructions described under

corrective action.

Fig. 30

16

English

MAINTENANCE AND INSPECTION

WARNING

Be sure to turned oﬀ the switch and remove the battery

before maintenance and inspection.

1. Inspecting the bit

Continued use of a dull or damaged bit will result in

reduced cutting eﬃ ciency and may cause overloading

of the motor. Replace the bit with a new one as soon as

excessive abrasion is noted.

2. Oiling

To ensure smooth vertical movement of the router,

occasionally apply a few drops of machine oil to the

sliding portions of the columns and end bracket.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

4. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

5. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

6. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

7. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 273.

For details regarding each bit type, please contact the

HiKOKI Authorized Service Center.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Table 3

Safeguard Function LED Light Display Corrective Action

Overload Protection On 0.1 second/oﬀ 0.1 second Remove the cause of the overloading.

Temperature Protection On 0.5 second/oﬀ 0.5 second Allow the tool and battery to thoroughly cool.

17

English

TROUBLESHOOTING

WARNING

○ To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source or remove the

battery from the main body before making any adjustments.

○ All electrical or mechanical repairs should be done only by qualiﬁ ed service technicians. Contact HiKOKI Authorized

Service Center.

1. Power tool

Problem Possible Cause Remedy

Tool doesn’t run No remaining battery power Charge the battery.

Battery isn’t fully installed. Push the battery in until you hear a click.

Tool suddenly stopped Tool was overburdened Get rid of the problem causing the

overburden.

During operation, lighten the applied

pressure.

Battery or tool overheated Allow the tool and battery to thoroughly cool.

Doesn’t cut well The bit is worn or missing teeth. Replace with a new bit.

The collet chuck is loose. Firmly tighten the collet chuck.

Switch can’t be pulled ON/OFF Lock button is pushed in Release the ON/OFF Lock button.

Battery cannot be installed Attempting to install a battery other than that

speciﬁ ed for the tool. Please install a multi volt type battery.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 97 dB (A)

Measured A-weighted sound pressure level: 86 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Cutting MDF:

Vibration emission value ah < 2.5 m/s2

Uncertainty K = 1.5 m/s2

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use

of the power tool can diﬀ er from the declared total

value depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

18

English

2. Charger

Symptom Possible cause Remedy

The charge indicator lamp

rapidly ﬂ ickers purple, and

battery charging doesn’t

begin.

The battery is not inserted all the way. Insert the battery ﬁ rmly.

There is foreign matter in the battery

terminal or where the battery is attached. Remove the foreign matter.

The charge indicator lamp

blinks red, and battery

charging doesn’t begin.

The battery is not inserted all the way. Insert the battery ﬁ rmly.

The battery is overheated. If left alone, the battery will automatically

begin charging if its temperature decreases,

but this may reduce battery life. It is

recommended that the battery be cooled in

a well-ventilated location away from direct

sunlight before charging it.

Battery usage time is short

even though the battery is

fully charged.

The battery’s life is depleted. Replace the battery with a new one.

The battery takes a long

time to charge. The temperature of the battery, the charger,

or the surrounding environment is extremely

low.

Charge the battery indoors or in another

warmer environment.

The charger’s vents are blocked, causing its

internal components to overheat. Avoid blocking the vents.

The cooling fan is not running. Contact a HiKOKI Authorized Service

Center for repairs.

The USB power lamp

has switched oﬀ and the

USB device has stopped

charging.

The battery’s capacity has become low. Replace the battery with one that has

capacity remaining.

Plug the charger’s power plug into an

electric socket.

USB power lamp does not

switch oﬀ even though the

USB device has ﬁ nished

charging.

The USB power lamp lights up green to

indicate that USB charging is possible. This is not a malfunction.

It is unclear what the

charging status of a USB

device is, or whether its

charging is complete.

The USB power lamp does not switch oﬀ

even when charging is complete. Examine the USB device that is charging to

conﬁ rm its charging status.

Charging of a USB device

pauses midway. The charger was plugged into an electrical

socket while the USB device was being

charged using the battery as the power

source.

This is not a malfunction.

The charger pauses USB charging for about

5 seconds when it is diﬀ erentiating between

power sources.

A battery was inserted into the charger while

the USB device was being charged using a

power socket as the power source.

Charging of the USB device

pauses midway when the

battery and the USB device

are being charged at the

same time.

The battery has become fully charged. This is not a malfunction.

The charger pauses USB charging for

about 5 seconds while it checks whether

the battery has successfully completed

charging.

Charging of the USB

device doesn’t start when

the battery and the USB

device are being charged

at the same time.

The remaining battery capacity is extremely

low. This is not a malfunction.

When the battery capacity reaches a certain

level, USB charging automatically begins.

19

Deutsch

(Übersetzung der Original-Gebrauchsanweisung)

f) Falls sich der Betrieb des Elektrowerkzeugs

in feuchter Umgebung nicht vermeiden lässt,

verwenden Sie eine Stromversorgung mit

Fehlerstromschutzeinrichtung (Residual

Current Device, RCD).

Durch den Einsatz einer

Fehlerstromschutzeinrichtung wird das Risiko eines

elektrischen Schlages reduziert.

3) Persönliche Sicherheit

a) Bleiben Sie wachsam, achten Sie auf das, was

Sie tun, und setzen Sie Ihren Verstand ein, wenn

Sie mit Elektrowerkzeugen arbeiten.

Benutzen Sie keine Elektrowerkzeuge, wenn

Sie müde sind oder unter Einﬂ uss von Drogen,

Alkohol oder Medikamenten stehen.

Bei der Arbeit mit Elektrowerkzeugen können bereits

kurze Phasen der Unaufmerksamkeit zu schweren

Verletzungen führen.

b) Benutzen Sie eine persönliche

Schutzausrüstung. Tragen Sie immer einen

Augenschutz.

Schutzausrüstung wie Staubmaske, rutschfeste

Sicherheitsschuhe, Schutzhelm und Gehörschutz

senken bei angemessenem Einsatz das

Verletzungsrisiko.

c) Vermeiden Sie unbeabsichtigtes Einschalten.

Achten Sie darauf, dass sich der Schalter

in der Aus- (Oﬀ -) Position beﬁ ndet, ehe Sie

das Gerät mit der Stromversorgung und/

oder Batteriestromversorgung verbinden, es

aufheben oder herumtragen.

Das Herumtragen von Elektrowerkzeugen mit

dem Finger am Schalter oder das Herstellen der

Stromversorgung bei betätigtem Schalter zieht

Unfälle regelrecht an.

d) Entfernen Sie sämtliche Einstellwerkzeuge

(Einstellschlüssel), ehe Sie das Elektrowerkzeug

einschalten.

Ein an einem beweglichen Teil des Elektrowerkzeugs

angebrachter Schlüssel kann zu Verletzungen

führen.

e) Überstrecken Sie sich nicht. Achten Sie jederzeit

darauf, sicher zu stehen und das Gleichgewicht

zu bewahren.

Dadurch haben Sie das Elektrowerkzeug in

unerwarteten Situationen besser im Griﬀ .

f) Tragen Sie geeignete Kleidung. Tragen Sie

keine lose Kleidung oder Schmuck. Halten Sie

Ihr Haar und Ihre Kleidung von beweglichen

Teilen fern.

Lose Kleidung, Schmuck oder langes Haar kann von

beweglichen Teilen erfasst werden.

g) Wenn Anschlüsse für Staubabsaug- und -

sammelvorrichtungen vorhanden sind, sorgen

Sie dafür, dass diese richtig angeschlossen und

eingesetzt werden.

Durch Entfernen des Staubes können

staubbezogene Gefahren vermindert werden.

h) Lassen Sie es nicht zu, dass die durch häuﬁ gen

Gebrauch von Werkzeugen erworbene

Vertrautheit Sie nachlässig macht und Sie

die Sicherheitsrichtlinien für das Werkzeug

ignorieren.

Eine unvorsichtige Handlung kann in

Sekundenbruchteilen zu schweren Verletzungen

führen.

ALLGEMEINE

SICHERHEITSHINWEISE FÜR

ELEKTROGERÄTE

WARNUNG

Bitte beachten Sie sämtliche mit diesem Elektrogerät

gelieferten Sicherheitshinweise, Anweisungen,

Illustrationen und technischen Angaben.

Wenn die nachfolgenden Anweisungen nicht befolgt

werden, kann es zu Stromschlag, Brand und/oder

ernsthaften Verletzungen kommen.

Bitte bewahren Sie alle Warnhinweise und

Anweisungen zum späteren Nachschlagen auf.

Der Begriﬀ „Elektrowerkzeug“ bezieht sich in den

Warnhinweisen auf Elektrowerkzeuge mit Netz-

(schnurgebunden) oder Akkubetrieb (schnurlos).

1) Sicherheit im Arbeitsbereich

a) Sorgen Sie für einen sauberen und gut

ausgeleuchteten Arbeitsbereich.

Zugestellte oder dunkle Bereiche ziehen Unfälle

förmlich an.

b) Verwenden Sie Elektrowerkzeuge niemals an

Orten, an denen Explosionsgefahr besteht,

wie zum Beispiel in der Nähe von leicht

entﬂ ammbaren Flüssigkeiten, Gasen oder

Stäuben.

Bei der Arbeit mit Elektrowerkzeugen kann es zu

Funkenbildung kommen, wodurch sich Stäube oder

Dämpfe entzünden können.

c) Sorgen Sie bei der Arbeit mit Elektrowerkzeugen

dafür, dass sich keine Zuschauer (insbesondere

Kinder) in der Nähe beﬁ nden.

Wenn Sie abgelenkt werden, können Sie die

Kontrolle über das Werkzeug verlieren.

2) Elektrische Sicherheit

a) Elektrowerkzeuge müssen mit passender

Stromversorgung betrieben werden. Nehmen

Sie niemals irgendwelche Änderungen am

Anschlussstecker vor. Verwenden Sie bei

Elektrowerkzeugen mit Schutzkontakt (geerdet)

niemals Adapterstecker.

Stecker im Originalzustand und passende

Steckdosen reduzieren das Stromschlagrisiko.

b) Vermeiden Sie Körperkontakt mit geerdeten

Gegenständen wie Rohrleitungen, Heizungen,

Herden oder Kühlschränken.

Bei Körperkontakt mit geerdeten Gegenständen

besteht ein erhöhtes Stromschlagrisiko.

c) Setzen Sie Elektrowerkzeuge niemals Regen

oder sonstiger Feuchtigkeit aus.

Wenn Flüssigkeiten in ein Elektrowerkzeug

eindringen, erhöht sich das Stromschlagrisiko.

d) Verwenden Sie das Anschlusskabel nicht

missbräuchlich. Tragen Sie das Elektrowerkzeug

niemals am Stromkabel, ziehen Sie es nicht

damit heran und ziehen Sie den Stecker nicht

am Anschlusskabel aus der Steckdose.

Halten Sie das Anschlusskabel von Hitzequellen,

Öl, scharfen Kanten und beweglichen Teilen

fern.

Beschädigte oder verdrehte Anschlusskabel

erhöhen das Stromschlagrisiko.

e) Verwenden Sie, wenn Sie ein Elektrowerkzeug

im Freien benutzen, ein für den Außeneinsatz

geeignetes Verlängerungskabel.

Ein für den Außeneinsatz geeignetes Kabel

vermindert das Stromschlagrisiko.

20

Deutsch

4) Einsatz und Pﬂ ege von Elektrowerkzeugen

a) Überbeanspruchen Sie Elektrowerkzeuge nicht.

Benutzen Sie das richtige Elektrowerkzeug für

Ihren Einsatzzweck.

Das richtige Elektrowerkzeug erledigt seine Arbeit

bei bestimmungsgemäßem Einsatz besser und

sicherer.

b) Benutzen Sie das Elektrowerkzeug nicht, wenn

es sich nicht am Schalter ein- und ausschalten

lässt.

Jedes Elektrowerkzeug, das nicht mit dem Schalter

betätigt werden kann, stellt eine Gefahr dar und

muss repariert werden.

c) Ziehen Sie den Stecker der Stromversorgung

ab und/oder entfernen Sie den Akkupack

vom Elektrowerkzeug, falls abnehmbar, ehe

Sie Einstellarbeiten vornehmen, Zubehörteile

tauschen oder das Elektrowerkzeug verstauen.

Solche präventiven Sicherheitsmaßnahmen

verhindern den unbeabsichtigten Anlauf des

Elektrowerkzeugs und die damit verbundenen

Gefahren.

d) Lagern Sie nicht benutzte Elektrowerkzeuge

außerhalb der Reichweite von Kindern,

lassen Sie nicht zu, dass Personen das

Elektrowerkzeug bedienen, die nicht mit dem

Werkzeug selbst und/oder diesen Anweisungen

vertraut sind.

Elektrowerkzeuge in ungeschulten Händen sind

gefährlich.

e) Wartung von Elektrowerkzeugen und Zubehör.

Prüfen Sie sie auf Fehlausrichtungen,

Leichtgängigkeit beweglicher Teile,

Beschädigungen von Teilen und auf alle

anderen Umstände, die sich auf den Betrieb des

Elektrowerkzeugs auswirken können. Lassen

Sie das Elektrowerkzeug bei Beschädigungen

reparieren, ehe Sie es benutzen.

Viele Unfälle mit Elektrowerkzeugen sind auf

schlechte Wartung zurückzuführen.

f) Halten Sie Schneidwerkzeuge scharf und

sauber.

Richtig gewartete Schneidwerkzeuge mit scharfen

Schneiden bleiben weniger häuﬁ g hängen und sind

einfacher zu beherrschen.

g) Benutzen Sie Elektrowerkzeuge, Zubehör,

Werkzeugspitzen und Ähnliches in

Übereinstimmung mit diesen Anweisungen

– beachten Sie dabei die jeweiligen

Arbeitsbedingungen und die Art der

auszuführenden Arbeiten.

Der Gebrauch des Elektrowerkzeugs für andere

als die vorgesehenen Anwendungen kann zu

gefährlichen Situationen führen.

h) Halten Sie Handgriﬀ e und Greiﬄ ächen trocken,

sauber und frei von Öl und Fett.

Rutschige Handgriﬀ e und Greiﬄ ächen lassen keine

sichere Handhabung und Kontrolle des Werkzeugs

in unerwarteten Situationen zu.

5) Verwendung und Pﬂ ege der Batterie

a) Laden Sie das Gerät nur mit dem vom Hersteller

empfohlenen Ladegerät auf.

Ein Ladegerät für einen speziellen Batterietyp

kann bei Verwendung mit anderen Batterien zu

Brandgefahr führen.

b) Verwenden Sie nur die für das Elektrowerkzeug

speziell empfohlenen Akkus.

Eine Verwendung von anderen Batterien kann zu

Verletzungen und Bränden führen.

c) Ist der Akku nicht in Gebrauch, achten Sie

darauf, dass er nicht mit Metallgegenständen,

beispielsweise Büroklammern, Münzen,

Schlüsseln, Nägeln, Schrauben oder anderen

kleinen Metallgegenständen in Kontakt kommt,

da diese Gegenstände einen Kurzschluss der

Anschlüsse verursachen können.

Ein Kurzschluss der Batterieanschlüsse kann zu

Verbrennungen oder Bränden führen.

d) Im Falle von missbräuchlichen Bedingungen

kann Flüssigkeit aus dem Akku austreten.

Vermeiden Sie in diesem Fall jeglichen Kontakt.

Sollten Sie dennoch mit der Batterieﬂ üssigkeit in

Berührung kommen, waschen Sie die betroﬀ ene

Stelle gründlich mit Wasser ab. Ist die Flüssigkeit

ins Auge geraten, suchen Sie einen Arzt auf.

Ausgetretene Batterieﬂ üssigkeiten können zu

Reizungen oder Verbrennungen führen.

e) Verwenden Sie keinen Akku oder kein Werkzeug,

der oder das beschädigt oder verändert ist.

Beschädigte oder veränderte Akkus können ein

unvorhersehbares Verhalten aufweisen, das zu

einem Feuer, einer Explosion oder Verletzung führen

kann.

f) Setzen Sie den Akku oder das Werkzeug keinem

Feuer oder keiner zu hohen Temperatur aus.

Die Einwirkung von Feuer oder einer Temperatur

über 130°C kann zu einer Explosion führen.

g) Befolgen Sie alle Anweisungen zum Auﬂ aden

und laden Sie den Akku oder das Werkzeug

nicht außerhalb des Temperarturbereichs auf,

der in der Anleitung angegeben ist.

Wenn Sie den Akku falsch oder bei Temperaturen

außerhalb des angegebenen Bereichs auﬂ aden,

kann der Akku beschädigt werden und die Gefahr

eines Brandes steigen.

6) Service

a) Lassen Sie Ihr Elektrowerkzeug durch

qualiﬁ zierte Fachkräfte und nur unter Einsatz

der passenden Originalersatzteile warten.

Dies sorgt dafür, dass die Sicherheit des

Elektrowerkzeugs nicht beeinträchtigt wird.

b) Warten Sie niemals beschädigte Akkus.

Die Wartung von Akkus ist stets vom Hersteller oder

autorisierten Dienstleistern durchzuführen.

VORSICHT

Von Kindern und gebrechlichen Personen fernhalten.

Werkzeuge sollten bei Nichtgebrauch außerhalb der

Reichweite von Kindern und gebrechlichen Personen

aufbewahrt werden.

SICHERHEITSHINWEISE FÜR DIE

AKKU-OBERFRÄSE

1. Halten Sie das Elektrowerkzeug an den isolierten

Griﬀ ﬂ ächen, wenn Sie Arbeiten ausführen, bei

denen das Schneidwerkzeug mit verborgenen

Kabeln in Kontakt geraten könnte.

Wenn Schneidewerkzeuge auf einen "gstromführenden"

Draht treﬀ en, können die freigelegten Metallteile das

Elektrowerkzeug "gunter Strom setzen" und dem

Bediener einen elektrischen Schlag versetzen.

2. Benutzen Sie Klemmen oder eine andere

praktische Vorrichtung zum Sichern und Halten des

Werkstücks auf einer stabilen Arbeitsﬂ äche.

Wenn Sie das Werkstück mit der Hand oder gegen

Ihren Körper halten, ist es nicht stabil und kann außer

Kontrolle geraten.

3. Einhändiges Arbeiten ist unstabil und gefährlich. Man

muß darauf achten, daß das Werkzeung mit beiden

Händen während des Betriebs gut festgehalten wird.

La page charge ...

Hikoki M3612DA 36V Cordless Multi-Volt Brushless Router Manuel utilisateur

Hikoki M3612DA 36V Cordless Multi-Volt Brushless Router Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents