Metabo DS 18DDX Manuel utilisateur

Marque: Metabo

Modèle: DS 18DDX

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual BEFORE operating the power tool. Please keep this manual available for other

users and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe

ser guardado en un lugar seguro.

Model

Modèle

Modelo DS 18DDX

Cordless Driver Drill

Perceuse-visseuse sans ﬁ l

Taladro atornillador a batería

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

English

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal

injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

English

12. Handle tool correctly.

Operate the tool according to the instructions provided

herein. Do not drop or throw the tool. Never allow the

tool to be operated by children, individuals unfamiliar

with its operation or unauthorized personnel.

13. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

14. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

15. Blades and accessories must be securely

mounted to the tool.

Prevent potential injuries to yourself or others. Blades,

cutting implements and accessories which have been

mounted to the tool should be secure and tight.

16. Never use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

17. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

18. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

19. Always wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

20. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

21. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

3. Hold power tool by insulated gripping surfaces,

when performing an operation where the

fastener may contact hidden wiring.

Fasteners contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

4. Always wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

5. Never place hands or other body parts near the drill

bit or chuck during operation. Hold the drill by its

handle only.

6. Because the cordless driver drill operates by battery

power, be aware of the fact that it can begin to operate

at any time.

7. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

8. Never touch moving parts.

Never place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

9. Never operate without all guards in place.

Never operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard or

safety feature before resuming operation of the tool.

10. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

11. Never use a power tool for applications other

than those speciﬁ ed.

Never use a power tool for applications other than

those speciﬁ ed in the instruction manual.

English

22. Deﬁ nitions for symbols used on this tool

V ............ volts

—

---

......... direct current

no .......... no load speed

--- /min ... revolutions or reciprocation per minute

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YKSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable batteries. Other type of batteries may

burst causing personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YKSL battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY metabo HPT BATTERIES.

OTHER TYPES OF BATTERIES MAY BURST AND

CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery

or battery charger can lead to

serious injury. To avoid these

injuries:

1. NEVER disassemble the battery.

English

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible

and ﬂ ammable items. Corrosive gas atmospheres

must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

2. NEVER incinerate the battery, even if it is damaged or

is completely worn out. The battery can explode in a

ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

English

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 3).

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

Power Output

2 to 3 digit number

Fig. 1

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Driver Drill (DS18DDX)

Indication

Clutch dial

Keyless chuck

Shift knob

LED light

Selector button

Housing

Battery

Handle

Switch trigger

Indication

Fig. 2

2. Battery 3. Battery Charger

Ventilation holes

Latch

Terminals

Battery

cover

Ventilation holes Terminals

Battery

cover

Latch Nameplate

Pilot lamp Guide rail

Fig. 3 Fig. 4

English

SPECIFICATIONS

1. Cordless Driver Drill

Model DS18DDX

Motor DC motor

No-load

speed

Low 0–440 /min

High 0–1,700 /min

Capacity

Drilling

Wood (Thickness

1-1/2 in. (38 mm)) 1-7/16 in. (36 mm)

(Soft Wood)

Metal (Thickness

1/16 in. (1.6 mm)) 1/2 in. (13 mm)

(Mild Steel)

Screw

Driver

Wood screw #14 × 3 in.

(6 mm × 75 mm)

Small screw 1/4 in. (6 mm)

Drill chuck capacity Maximum gripping

diameter 1/2 in. (13 mm)

Battery

Model BSL1815 (1.5 Ah) / BSL1820M (2.0 Ah)

Type Li-ion battery

Voltage DC 18 V

Weight 2.7 lbs. (1.2 kg)

2. Battery Charger

Model UC18YKSL

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL1815 : Approx. 40 min

BSL1820M : Approx. 60 min

Charging voltage DC 14.4–18 V

Charging current DC 2.0 A

Weight 0.8 lbs. (0.35 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

English

ASSEMBLY AND OPERATION

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted

into the receptacle, pilot lamp will blink in red. (At

1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in

Fig. 6. Make sure it contacts the bottom of the battery

charger.

Battery

Pilot lamp

Fig. 6

3. Charging

○

When the battery is connected to the battery charger,

charging will commence and the pilot lamp will light in

red. (See Table 2)

NOTE

If the pilot lamp does not light or blink in red, pull out

the plug from the receptacle and check if the battery

is properly mounted.

○

When the battery is fully charged, the pilot lamp

will blink in red slowly. (At 1-second intervals) (See

Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 2, according to the condition of the charger or

the rechargeable battery.

APPLICATIONS

○

Use as a drill

Drilling of soft steel, wood, plastic and aluminum

materials.

○

Use as a screwdriver

Tightening and loosening of machine screws, wood

screws and tapping screws.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

○

How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 5).

○

How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery (Fig. 5).

Battery

Push

Pull out Insert Handle

Latch

Fig. 5

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the

nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn out.

English

Table 2

Indications of the pilot lamp

Pilot lamp

(red)

Before charging Blinks Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

While charging Lights Lights continuously

Charging

complete Blinks Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Overheat

standby Blinks Lights for 1 second. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

impossible Flickers Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds) Malfunction in the battery or

the charger

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3 Recharging ranges of batteries

Rechargeable

batteries Temperatures at which the

battery can be recharged

BSL1815

BSL1820M 32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery UC18YKSL

BSL1815 Approx. 40 min

BSL1820M Approx. 60 min

NOTE

The charging time may vary according to temperature

and power source voltage.

4 Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2–3 times.

How to make the batteries perform longer.

(1)

Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2)

Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

English

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated

because it has been left for a long time in a

location subject to direct sunlight or because the

battery has just been used, the pilot lamp of the

charger lights for 1 second, does not light for 0.5

seconds (oﬀ for 0.5 seconds).

The battery will not be recharged. In such a case,

let the battery cool before charging.

●

When the pilot lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign

objects in the charger’s battery connector. If

there are no foreign objects, it is probable that

the battery or charger is malfunctioning. Take it

to your authorized Service Center.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

OPERATION

1. Mounting and dismounting of the bit.

(1) Mounting the bit.

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front)

to open the clip on the keyless chuck. After inserting

a driver bit, etc., into the keyless drill chuck, and

tighten the sleeve by turning it toward the right (in the

clockwise direction as viewed from the front). (See

Fig. 7).

Tighten

Loosen Sleeve

Fig. 7

CAUTION

When mounting a bit into the keyless chuck,

tighten ﬁ rmly. If the sleeve is not tight, the bit

may slip or fall out, causing injury.

NOTE

If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front),

and then take out the bit etc. (See Fig. 7)

NOTE

Loosening stuck or hard to move sleeves.

Grasp the bit installed in the keyless chuck, in a vise

or similar tool.

Set the clutch dial position to “1–11” and turn on the

switch. The motor then starts.

Finally, rotate the sleeve to the left, and it will loosen.

2. Conﬁ rm that the battery is mounted correctly.

3. Check the rotational direction.

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn

the bit counterclockwise (See Fig. 8). (The and

marks are provided on the body.)

marks marks

Switch trigger

Selector button

Fig. 8

CAUTION

The selector button can not be switched while

the power tool is turning. To switch the selector

button, stop the power tool, then set the selector

button.

4. Change rotation speed.

Shift knob

Low speed

Fig. 9

English

CAUTION

●

When changing the rotational speed with the

shift knob, conﬁ rm that the switch is oﬀ .

Changing the speed while the motor is rotating

will damage the gears.

●

When a large force is required for operation

(operations indicated in the following chart) set

the shift knob to “LOW”. If “HIGH” is set and the

unit is used, it may cause the motor to burn out

or malfunction prematurely.

5. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown in

Table 5.

Shift knob

High speed

Fig. 10

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (See

Figs. 9 and 10).

When the shift knob is set to “LOW”, the drill rotates at

a low speed. When set to “HIGH”, the drill rotates at a

high speed.

Table 5

Work Cap position Suggestions

Drilling

Wood

Use for drilling purpose.Steel

Aluminum

Screw tightening

Small screw 1–20 Use the bit and socket matching the screw diameter.

Wood screw 1– Use after drilling a pilot hole.

6. Conﬁ rm the clutch dial position (See Fig. 11).

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the

clutch dial is set.

mark Triangle mark

Clutch dial

Strong

Weak

Fig. 11

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 5, 10 ... 20” on the clutch dial, or the

dot, with the triangle mark on the outer body.

(2) When using this unit as a drill, line up the clutch dial

drill mark “ ” with the triangle mark on the outer

body.

CAUTION

●

The clutch dial cannot be set between the

numbers “1, 5, 10 ... 20” or the dot.

●

Do not use with the clutch dial set at the line

between the number “20” and the drill mark

“”. Doing so may cause damage (See Fig. 12).

mark Triangle mark

Line

Fig. 12

English

8. Switch operation

○

When the switch trigger is depressed, the tool rotates.

When the trigger is released, the tool stops.

When releasing the trigger of the switch, the brake will

be applied for immediate stopping.

○

The rotational speed of the drill can be controlled by

varying the amount that the switch trigger is pulled.

Speed is low when the switch trigger is pulled slightly

and increases as the switch trigger is pulled more.

CAUTION

●

The motor rotation may be locked to cease while

the unit is used as drill. While operating the

driver drill, take care not to lock the motor.

●

If the motor is locked, immediately turn the power

oﬀ . If the motor is locked for a while, the motor or

battery may be burnt.

●

Do not tighten too strongly as the screw heads

will be damaged.

9. How to select rotational speed

CAUTION

●

The selection examples shown in Table 7 should

be considered as general standard. As diﬀ erent

types of tightening screws and diﬀ erent materials

to be tightened are used in actual works proper

adjustments are naturally necessary.

●

When using the driver drill with a machine screw

at HIGH (high speed), a screw may damage or a

bit may loose due to the tightning torque is too

strong. Use the driver drill at LOW (low speed)

when using a machine screw.

NOTE

The use of the battery in a cold condition (below

0 degree Centigrade) can sometimes result in the

weakened tightening torque and reduced amount of

work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

7. Tightening torque adjustment.

(1) Tightening torque

Tightening torque should correspond in its intensity to

the screw diameter. When too strong power is used,

the screw head may be broken or be injured.

Be sure to adjust the clutch dial position according to

the screw diameter.

(2) Tightening torque indication (See Fig. 11)

The tightening torque diﬀ ers depending on the type of

screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 5, 10 ... 20” on the clutch dial, and a dot.

The tightening torque at position “1” is the weakest

and the torque is strongest at the highest number.

(3) Adjusting the tightening torque (See Fig. 11)

Rotate the clutch dial and line up the numbers “1, 5,

10 ... 20” on the clutch dial, or the dot, with the triangle

mark on the outer body. Adjust the clutch dial in the

weak or the strong torque direction according to the

torque you need.

Table 6 Tightening torque

Clutch dial

position Tightening torque

1 Approx. 5.3 in.-lbs. (0.6 N-m)

5 Approx. 11.7 in.-lbs. (1.3 N-m)

10 Approx. 19.6 in.-lbs. (2.2 N-m)

15 Approx. 27.5 in.-lbs. (3.1 N-m)

20 Approx. 35.4 in.-lbs. (4.0 N-m)

Table 7

Work Cap Position Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Drilling

Wood For 1–7/16 in. (36 mm) or smaller

diameters. For 11/16 in. (18 mm) or smaller

diameters.

Metal ——— For drilling with a metal working

drill bit.

Screw

tightening

Small screw 1–20 For 1/4 in. (6 mm) or smaller

nominal diameter screws.

For 1/4 in. (6 mm) or smaller

nominal diameter screws.

Wood screw 1– For 5/32 in. (4.1 mm) or smaller

nominal diameter screws.

English

10. Remaining battery indicator

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light

the indicator lamp. (Fig. 13, Table 8)

The indicator will shut oﬀ approximately 3 seconds

after the remaining battery indicator switch is pressed.

It is best to use the remaining battery indicator as

a guide since there are slight diﬀ erences such as

ambient temperature and the condition of the battery.

Also, the remaining battery indicator may vary from

those equipped to a tool or charger.

Table 8

State of lamp Battery Remaining Power

Lights ;

The battery remaining power is

over 75%

Lights ;

The battery remaining power is

50%–75%.

Lights ;

The battery remaining power is

25%–50%.

Lights ;

The battery remaining power is

less than 25%

Blinks ;

The battery remaining power

is nearly empty. Recharge the

battery soonest possible

Blinks ;

Output suspended due to high

temperature. Remove the

battery from the tool and allow it

to fully cool down.

Blinks ;

Output suspended due to failure

or malfunction. The problem

may be the battery so please

contact your dealer.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and

battery characteristics, read it as a reference.

Display panel

Remaining battery

indicator lamp Remaining battery

indicator switch

Fig. 13

NOTE

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

11. How to use the LED light

While the switch is pulled, the LED light will

automatically light up the tip portion of the tool.

(Fig. 14)

The LED light will automatically turn oﬀ 10 seconds

after the switch is released.

The LED light also functions as a warning signal that

lights up during use.

For details, see “13. LED light warning signals”.

Switch

trigger

LED light

Fig. 14

CAUTION

●

Do not expose directly your eye to the LED light

by looking into the LED light.

If your eye is continuously exposed to the LED

light, your eye will be hurt.

12. Using the hook (sold separately)

The hook is used to hang up the power tool to your

waist belt while working.

English

CAUTION

●

When using the hook, hang up the power tool

ﬁ rmly not to drop accidentally.

If the power tool is dropped, it may lead to an

accident.

●

When carrying the power tool with hooked to

your waist belt, do not ﬁ t any bit to the tip of

power tool. If the sharp bit such as drill is ﬁ tted

to the power tool when carrying it with hooked to

your waist belt, you will be injured.

●

Install securely the hook. Unless the hook is

securely installed, it may cause an injury while

using.

(1) Placing the hook and tightening the screws.

Install securely the hook in the groove of power

tool and tighten the screws to ﬁ x the hook ﬁ rmly.

(Fig. 15)

Groove

Screw

Hook

Nut

Fig. 15

(2) Removing the hook.

Remove the screws ﬁ xing the hook with Philips screw

driver. (Fig. 16)

Hook

Screw

Fig. 16

13. LED light warning signals (Fig. 17)

This product features functions that are designed

to protect the tool itself as well as the battery. While

the switch is pulled, if any of the safeguard functions

activate during operation, the LED light will blink as

described in Table 9. When any of the safeguard

functions are triggered, immediately remove your

ﬁ nger from the switch and follow the instructions

described under corrective action.

Fig. 17

Table 9

Safeguard Function LED Light Display Corrective Action

Overburden Protection On 0.1 second/oﬀ 0.5 second If the operating with the shift knob set on

HIGH, adjust to LOW and continue operation.

Remove the cause of the overburdening.

Temperature Protection On 0.3 second/oﬀ 0.3 second Allow the tool and battery to thoroughly cool.

OPERATIONAL CAUTIONS

Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous bolt-tightening work may cause the

temperature of the unit to rise, activating the

temperature protection circuit and automatically

stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous tightening wood screw works,

rest the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

English

1. Checking the condition of the bit

The bits should be checked regularly. If worn or

broken bits can slip or decrease the eﬃ ciency of the

motor and burn it out.

Replace worn bits with new ones.

CAUTION

If you use a driver bit of which point is worn or

broken, it will be dangerous since it slips. So

replace it with a new one.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them

and make sure they are tight.

CAUTION

Using this power tool with loosened, screws is

extremely dangerous.

3. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for

they may damage the plastics.

4. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected

on the terminals.

Failure to do so may result in malfunction.

5. Disposal of the exhausted battery

WARNING

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable.

At the end of it’s useful life, under various state

and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste oﬃ cials for details in

your area for recycling options or proper disposal.

MAINTENANCE AND INSPECTION

CAUTION:

Pull out battery before doing any inspection or maintenance.

6. Storage

Storing in a place below 104°F (40°C) and out of the

reach of children.

NOTE

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time

may be recovered by repeatedly charging and using

the batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

7. Service and repairs

All quality power tools will eventually require servicing or

replacement of parts because of wear from normal use.

To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a

metabo HPT AUTHORIZED SERVICE CENTER, ONLY.

CAUTION

In the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

Important notice on the batteries for the metabo HPT

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

English

TROUBLESHOOTING GUIDE

WARNING

●

To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source

or remove the battery from the main body before making any adjustments.

●

All electrical or mechanical repairs should be done only by qualiﬁ ed service technicians. Contact

metabo HPT Authorized Service Center.

Problem Possible Cause Possible Solution

Tool doesn’t run No remaining battery power Charge the battery.

Battery isn’t securely attached. Push in the battery until a click is heard.

Tool suddenly stopped Tool was overburdened Remove the cause of the overburdening.

Battery or tool overheated Allow the tool and battery to thoroughly

cool.

Tool bits

-can’t be attached

-fall oﬀ

The shape of the attachment portion

doesn’t match The chucking diameter of the keyless

chuck is 5/64 in (2 mm) to 1/2 in (13 mm).

Use a bit that falls within the stated range.

The lock of the keyless chuck is worn Contact a metabo HPT Authorized Service

Center and arrange to have the old keyless

chuck replaced with a new one.

Switch can’t be pulled Forward/reverse selector button is

positioned halfway Press the button ﬁ rmly into position for the

desired direction of rotation.

Screw head slips or comes

loose. Bit number doesn’t match with the screw

size Install a suitable bit.

The bit is worn Replace with a new bit.

Holes can’t be smoothly

drilled. The drill is worn Replace with a new drill.

Rotation speed isn’t appropriate Adjust the rotation speed (HIGH/LOW) to

match the material to be drilled.

The drill is rotating in reverse Switch to forward rotation.

Battery will not charged. Battery not installed into charger properly. Insert battery into charger until charge

status lamp (red) appears.

Charger not plugged in. Plug charger into a working receptacle.

Battery temperature too hot Remove battery from charger, cool battery.

For more detail, refer to “Charging

Method”.

Battery temperature too cold Remove battery from charger, move

battery and charger to a surrounding air

temperature of above 32°F (0°C).

For more detail, refer to “Charging

Method”.

English

ACCESSORIES

WARNING

ALWAYS use Only authorized metabo HPT replacement parts and accessories. NEVER use replacement

parts or accessories which are not intended for use with this tool. Contact metabo HPT if you are not sure

whether it is safe to use a particular replacement part or accessory with your tool.

The use of any other attachment or accessory can be dangerous and could cause injury or mechanical

damage.

NOTE

Accessories are subject to change without any obligation on the part of the metabo HPT.

STANDARD ACCESSORIES

DS18DDX

(2EGK) Phillips bit (No. 2 × 65L) (Code No. 983006) ......................................... 1

Battery (BSL1815) .................................................................................. 2

Battery Charger (UC18YKSL) ................................................................ 1

Plastic Case ........................................................................................... 1

Battery cover (Code No. 329897) .......................................................... 1

DS18DDX

(2BGK) Phillips bit (No. 2 × 65L) (Code No. 983006) ......................................... 1

Battery (BSL1820M)............................................................................... 2

Battery Charger (UC18YKSL) ................................................................ 1

Plastic Case ........................................................................................... 1

Battery cover (Code No. 329897) .......................................................... 1

OPTIONAL ACCESSORIES.....sold separately

○

Battery (BSL1815 / BSL1820M)

○

Hook

NOTE

Speciﬁ cations are subject to change without any obligation on the part of the metabo HPT.

English

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce

mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des

règles ou précautions de base de sécurité. Un accident peut la plupart du temps être évité si l’on reconnaît une situation

de danger potentiel avant qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode d’emploi et dans

les sections qui contiennent les instructions de fonctionnement et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un endommagement de la machine sont

identiﬁ és par AVERTISSEMENTS sur l’outil motorisé et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spéciﬁ quement recommandée par metabo HPT.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient entraîner

la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent entraîner de

mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

SÉCURITÉ

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX CONCERNANT LES OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lire tous les avertissements de sécurité et toutes les instructions

Tout manquement à observer ces avertissements et instructions peut engendrer des chocs électriques, des

incendies et/ou des blessures graves.

Conservez tous les avertissements et toutes les instructions pour vous y référer ultérieurement.

Le terme “outil électrique”, utilisé dans les avertissements, se réfère aux outils électriques (câblé) ou aux outils à

piles (sans ﬁ l).

1) Sécurité de l’aire de travail

a) Maintenir l’aire de travail propre et bien

éclairée.

Les endroits encombrés ou sombres sont

propices aux accidents.

b) Ne pas utiliser d’outils électriques en

présence de liquides, gaz ou poussière

inﬂ ammables, au risque de provoquer une

explosion.

Les outils électriques créent des étincelles

susceptibles d’enﬂ ammer la poussière.

c) Ne pas laisser les enfants et les visiteurs

s’approcher de vous lorsque vous utiliser un

outil électrique.

Les distractions peuvent faire perdre le contrôle.

2) Sécurité électrique

a) Les prises de l’outil électrique doivent

correspondre à la prise secteur.

Ne jamais modiﬁ er la prise.

Ne pas utiliser d’adaptateurs avec les outils

électriques mis à la masse.

Les prises non modiﬁ ées et les prises secteurs

correspondantes réduisent les risques de choc

électrique.

b) Eviter tout contact avec les surfaces mises

à la masse telles que les tuyaux, radiateurs,

bandes et réfrigérateurs.

Le risque de choc électrique est accru en cas de

mise à la masse du corps.

c) Ne pas exposer les outils électriques à la

pluie ou à des conditions humides.

Si l’eau pénètre dans l’outil, cela augmente les

risques de choc électrique.

d) Ne pas utiliser le cordon à tort. Ne jamais

utiliser le cordon pour transporter ou

débrancher l’outil électrique.

Français

La page charge ...

Metabo DS 18DDX Manuel utilisateur

Marque: Metabo

Modèle: DS 18DDX

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Metabo DS 18DDX User manual
español: Metabo DS 18DDX Manual de usuario

Documents connexes

Metabo NP18DSAL Manuel utilisateur

Metabo DS 18DDX Manuel utilisateur

Metabo DS 18DDX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents