KitchenAid KBSS271TSS00 Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

®itchen kid ®
OUTDOOR GRILLS
BUILT-IN INSULATED JACKET GRILLS
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
or visit our website at www.kitchenaid.com
In Canada, for assistance, installation and service, call: 1-800-807-6777
or visit our website at www.Kitchenaid.ca
P
GRILS D'EXTERIEUR
GRILS ENCASTRI_S AVEC CHEMISAGE ISOLI_
Au Canada, pour assistance, installation ou service composez le 1-800-807-6777
ou visitez notre site web & www.Kitchenaid.ca
Table of Contents/Table des matieres ............................................................................. 2
iMPORTANT:
Save for local electrical inspector's use.
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
iMPORTANT :
_, conserver pour consultation par I'inspecteur local des installations _lectriques.
Installateur : Remettre les instructions d'installation au propri_taire.
Propri6taire : Conserver les instructions d'installation pour r_f_rence ult_rieure.
Models/Modeles KBSS271T, KBSS361T, KBSU367T, KBSU487T
W10138384C
TABLEOF CONTENTS
OUTDOOR GRILL SAFETY ............................................................ 3
INSTALLATION REQUIREMENTS ................................................ 4
Tools and Parts ............................................................................ 4
Location Requirements ................................................................ 5
Product Dimensions ..................................................................... 5
Built-In Outdoor Grill Enclosure ................................................... 5
Cabinet Cutout Dimensions ......................................................... 6
Electrical Requirements ............................................................... 8
Gas Supply Requirements ........................................................... 9
Gas Connection Requirements .................................................. 10
INSTALLATION INSTRUCTIONS ................................................ 11
Unpack Grill................................................................................ 11
Make Gas Connection ............................................................... 11
Plug in Grill ................................................................................. 12
Conversion to LP Gas ................................................................ 12
Check and Adjust the Burners ................................................... 13
OUTDOOR GRILL USE ................................................................ 15
Using Your Outdoor Grill............................................................ 15
Using Your Infrared Sear Burner ................................................ 16
Using Your Rotisserie................................................................. 17
Rotisserie Cooking Tips ............................................................. 18
Using Your Smoker Box ............................................................ 19
Hood Lights................................................................................ 19
TIPS FOR OUTDOOR GRILLING ............................................... 19
Cooking Methods ....................................................................... 20
Grilling Chart............................................................................... 20
OUTDOOR GRILL CARE ............................................................. 22
Changing the Light Bulb ............................................................ 22
General Cleaning ........................................................................ 22
TROUBLESHOOTING .................................................................. 24
ASSISTANCE OR SERVICE ......................................................... 24
In the U.S.A................................................................................ 24
Accessories ................................................................................ 24
In Canada ................................................................................... 25
WAR RANTY .................................................................................. 25
TABLEDES MATIERES
SECURITE DU GRIL D'EXTERIEUR ........................................... 27
EXIGENCES D'INSTALLATION ................................................... 29
Outillage et pieces ...................................................................... 29
Exigences d'emplacement ......................................................... 29
Dimensions du produit ............................................................... 30
Enceinte du gril d'exterieur encastre ......................................... 30
Dimensions de I'ouverture & decouper dans le placard ............ 31
Specifications electriques .......................................................... 33
Specifications de I'alimentation en gaz ..................................... 34
Exigences concernant le raccordement au gaz ........................ 35
INSTRUCTIONS D'INSTALLATION ............................................. 36
Deballage du gril......................................................................... 36
Raccordement au gaz ................................................................ 36
Branchement du gril ................................................................... 37
Conversion pour I'alimentation au propane ............................... 38
Contr61e et reglage des brQleurs................................................ 38
UTILISATION DU GRIL D'EXTI_RIEUR ....................................... 40
Utilisation du gril d'exterieur ....................................................... 40
Utilisation du brQleur a infrarouge.............................................. 42
Utilisation du tournebroche ........................................................ 42
Conseils de cuisson a raide du tournebroche .......................... 43
Utilisation du fumoir ................................................................... 44
Lampes sous le capot ................................................................ 44
CONSEILS POUR L'UTILISATION DU GRIL D'EXTI_RIEUR ...44
Methodes de cuisson ................................................................. 45
Tableau de cuisson au gril ......................................................... 45
ENTRETIEN DU GRIL D'EXTI_RIEUR ......................................... 48
Changement de I'ampoule d'eclairage ...................................... 48
Nettoyage general ...................................................................... 48
DI_PANNAGE ................................................................................. 50
ASSISTANCE OU SERVICE ......................................................... 51
Accessoires ................................................................................ 51
GARANTIE ..................................................................................... 51
2
OUTDOOR GRILL SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
_, DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department.
WARNING
1. Do not store or use gasoline or other
flammable liquids or vapors in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
State of California Proposition 65 Warnings:
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
In the State of Massachusetts, the following installation instructions apply:
m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
m If using a ball valve, it shall be a T-handle type.
m A flexible gas connector, when used, must not exceed 3 feet.
IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2000 ft (609.6 m) orifice
conversion is required. See "Gas Supply Requirements" section. It is the responsibility of the installer to comply with the minimum
installation clearances specified on the model/serial rating plate. The model/serial rating plate for built-in models can be found on the
right-hand side of the grill. The model/serial rating plate for freestanding models can be found on the right-hand inside cabinet wall.
iMPORTANT SAFETY iNSTRUCTiONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the outdoor cooking
gas appliance, follow basic precautions, including the
following:
m Do not install portable or built-in outdoor cooking gas
appliances in or on a recreational vehicle, portable trailer,
boat or in any other moving installation.
m Always maintain minimum clearances from combustible
construction, see "Location Requirements" section.
m The outdoor cooking gas appliance shall not be located
under overhead unprotected combustible construction.
m This outdoor cooking gas appliance shall be used only
outdoors and shall not be used in a building, garage, or any
other enclosed area.
m Keep any electrical supply cord and fuel supply hose away
from any heated surfaces.
m Keep outdoor cooking gas appliance area clear and free
from combustible materials, gasoline and other flammable
vapors and liquids.
m Do not obstruct the flow of combustion and ventilation air.
Keep the ventilation openings of the cylinder enclosure free
and clear from debris.
m Inspect the gas cylinder supply hose before each use of the
outdoor cooking gas appliance. If the hose shows
excessive abrasion or wear, or is cut, it MUST be replaced
before using the outdoor cooking gas appliance. Contact
your dealer and use only replacement hoses specified for
use with the outdoor cooking gas appliance.
m Visually check the burner flames. They should be blue.
Slight yellow tipping is normal for LP gas.
m Check and clean burner/venturi tube for insects and insect
nest. A clogged tube can lead to fire under the outdoor
cooking gas appliance.
SAVE THESE
The LP gas supply cylinder to be used must be:
- constructed and marked in accordance with the
Specification for LP Gas Cylinders of the U.S. Department
of Transportation (DOT) or the National Standard of
Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes
for Transportation of Dangerous Goods; and Commission.
- provided with a listed overfilling prevention device.
- provided with a cylinder connection device compatible
with the connection for outdoor cooking gas appliances.
Always check connections for leaks each time you connect
and disconnect the LP gas supply cylinder. See
"Installation Instructions" section.
When the outdoor cooking gas appliance is not in use, the
gas must be turned off at the supply cylinder.
Storage of an outdoor cooking gas appliance indoors is
permissible only if the cylinder is disconnected and
removed from the outdoor cooking gas appliance.
Cylinders must be stored outdoors and out of the reach of
children and must not be stored in a building, garage, or
any other enclosed area.
The pressure regulator and hose assembly supplied with
the outdoor cooking gas appliance must be used. A
replacement pressure regulator and hose assembly
specific to your model is available from your outdoor
cooking gas appliance dealer.
Gas cylinder must include a collar to protect the cylinder
valve.
For appliances designed to use a CGA791 Connection:
Place a dust cap on cylinder valve outlet whenever the
cylinder is not in use. Only install the type of dust cap on
the cylinder valve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result in leakage
of propane.
If the following information is not followed exactly, a fire
causing death or serious injury may occur.
Do not store a spare LP gas cylinder under or near this
outdoor cooking gas appliance.
Never fill the cylinder beyond 80 percent full.
iNSTRUCTiONS
INSTALLATION REQUIREMENTS
Parts Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
Tape measure Wrench or pliers
Small, flat-blade screwdriver Pipe wrench
Flat-blade screwdriver Scissors or cutting pliers
#2 and #3 Phillips screwdriver (to remove tiedowns)
Level Noncorrosive
leak-detection solution
Gas line shutoff valve
1/2"male pipe thread nipple for connection to pressure
regulator
Pipe-joint compound resistant to LP gas
CSA design-certified outdoor flexible stainless steel
appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply
line as needed.
Parts Supplied
Convertible regulator set for 4" WCP Natural gas.
1 single-prong plug/500 mAmp transformer assembly, on
some models
1 single-prong plug/5,000 mAmp transformer assembly
Additional Parts Supplied (on some models)
1.5-volt "D" size alkaline battery
Rotisserie motor mounting bracket
Rotisserie motor
Rotisserie forks
Rotisserie spit
Smoker box
l,,OQ;:ll:]Ol} I;,_,.@:]!IJl [/" !_I@I}l'I>
i
Explosion Hazard
Do not store fuel tank in a garage or indoors.
Do not store grill with fuel tank in a garage or indoors.
Failure to follow these instructions can result in death,
explosion, or fire.
Fire Hazard
Do not use grill near combustible materials.
Do not store combustible materials near grill.
Doing so can result in death or fire.
Select a location that provides minimum exposure to wind and
traffic paths. The location should be away from strong draft
areas.
Do not obstruct flow of combustion and ventilation air.
Clearance to combustible construction for built-in and
freestanding outdoor grills:
A minimum of 24" (58.0 cm) must be maintained between the
front of the grill hood, sides and back of the grill and any
combustible construction.
A zero clearance may be maintained on the insulated jacket
surface to combustible construction.
Rotisserie
A 6" (15.2 cm) minimum clearance is needed for the rotisserie
motor.
A grounded, 3-prong outlet located to the left of the grill is
required. See "Electrical Requirements" section.
_1' ] ................... . _
38" /
(96.5 Cm)
B
_i 11¾''
.6cm)
)
237/8,,
(60.5cm)
A. 27" (68.6 cm)
36" (91.4 cm)
48" (121.9 cm)
B. 27" (68.6 cm) models - 32z_ '' (83.3 cm)
36" (91.4 cm) models - 41 z_,,(106.2 em)
48" (121.9 cm) models - 53 z_''(136.6 cm)
Su tt:,,,,ts tJoo: CAll [i}J closs:
This built-in outdoor grill is only for installation in a built-in
enclosure constructed of combustible and non-combustible
materials. Some types of non-combustible materials could be
brick, firewall or steel. Some types of combustible materials
could be wood or laminate.
The enclosure for the built-in outdoor grill is to be a minimum
of 11s4" [29.8 cm] high x 24" [61.0 cm] deep x (33" [83.8 cm] for
27" [68.6 cm] grill and 42" [106.7 cm] for 36" [91.4 cm] grill and
54" [137.2 cm] for 48" [121.9 cm] grill) wide.
Cabine Cutout!: ©imens:ions
The installation of this grill must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code,
ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.
Copies of the standards listed may be obtained from:
CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
NOTE: The grill drops into the opening and the bottom of the grill should be supported by the bottom support of the cabinet cutout.
The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor
products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and
minimum spacing must be followed.
C
3" (7-en_oO_
to oP
E
E
K
F
H A
Between 2 or more sets of Access Doors adjacent to each other:
K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees
K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees
Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:
K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees
Between a Trash Drawer, Utility Drawer, or Warming Drawer:
K = 3" (7.6 cm)
6
Cabinet Height and Depth Dimensions
With outdoor refrigerator
Grill with insulated jacket
Grill without insulated jacket
Dimension A Minimum
37" (94.0 cm)
361/2'' (92.7 cm)
351/2"(90.2 cm)
Dimension B Minimum
26" (66.0 cm)
27" (68.6 cm)
26" (66.0 cm)
Grill Size Dimension C Dimension D Dimension E
27" (68.6 cm) 29%" (75.2 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)
36" (91.4 cm) 388/8'' (98.1 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)
48" (121.9 cm) 50%" (128.6 cm) 103_'' (27.3 cm) 227/8'' (58.1 cm)
Cutout Dimensions - Built-in Grill with Insulated Jacket
Grill Size Dimension C Dimension D Dimension E
27" (68.6 cm) 33" (83.8 cm) 11%" (29.8 cm) 24" (61.0 cm)
36" (91.4 cm) 42" (106.7 cm) 11%" (29.8 cm) 24" (61.0 cm)
48" (121.9 cm) 54" (137.2 cm) 11%" (29.8 cm) 24" (61.0 cm)
Burner Position Dimension C Dimension D Dimension E
Front to Back 131/2'' (34.3 cm) 10%" (27.3 cm) 228/8'' (57.5 cm)
Side by Side 241/2'' (62.2 cm) 10%" (27.3 cm) 167/8'' (42.9 cm)
Cutout Dimensions - Built-in Sear Burner
Dimension C Dimension D Dimension E
131/2'' (34.3 cm) 10%" (27.0 cm) 221Vie'' (57.6 cm)
Cutout Dimensions - Built-in Refreshment Center
Dimension C Dimension D Dimension E
301/2"(77.5 cm) 103_'' (27.3 cm) 23" (58.4 cm)
Cutout Dimensions - Built-in Access Doors
Door Size Dimension F Dimension L*
18" (45.7 cm) 163/le'' (41.1 cm) 11/2'' (3.8 cm)
27" (68.6 cm) 251/8'' (63.8 cm) 11/2"(3.8 cm)
30" (76.2 cm) 281/8'' (71.4 cm) 11/2"(3.8 cm)
36" (91.4 cm) 341/8'' (86.7 cm) 11/2"(3.8 cm)
48" (121.9 cm) 461/8'' (117.2 cm) 11/2'' (3.8 cm)
*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.
Dimension G Dimension H
24" (61.0 cm) 35W' (89.5 cm)
Cutout Dimensions - Outdoor Ice Maker
Dimension G Dimension H
18" (45.7 cm) 34" (86.4 cm) min. to 341/2"(87.6 cm) max.
Warming Drawer Size Dimension J
24" (61.0 cm) 221/2"(57.2 cm)
Dimension M Dimension L*
121¼'' (31.1 cm) 11/2'' (3.8 cm)
*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.
Built-in Outdoor Grill Enclosure Ventilation for LP Gas:
An enclosure for an LP gas fuel tank is to be ventilated by
openings at both the top and lower levels of the enclosure.
If converting to LP gas these vents are to be in the enclosure:
An enclosure for use with an LP gas fuel tank for built-in
installation is to have at least one ventilation opening on an
exposed exterior side located within 5" (12.7 cm) of the top is to
be a minimum of 20 in.2(129.0 cm2). One ventilation opening
within 1" (2.5 cm) of the bottom of the enclosure and the bottom
opening is to be a minimum of 10 in.2(64.5 cm_).All vent
openings are to be unobstructed. Every opening is to be a
minimum of 1/8"(0.32 cm) wide.
m)too,.
10 in 2(64 5 crn2) rain /_'_"_
"_' (12.7 cm) max.
£:i',1@CI: /_,,@;]!
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Check with a qualified electrician if you are not sure whether the
grill is properly grounded.
A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is
required.
It is recommended that a separate circuit servicing only this grill
be provided.
8
The model/serial number rating plate is located on the right-hand
side of the grill. See the following illustration.
...._A
A. Model/serial number plate
Recommended Ground Method
The outdoor grill, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes,
with the National Electrical Code ANSI/NFPA 70, or Canadian
Electrical Code, CSA C22.1.
Copies of the standards listed above may be obtained from:
CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
S ........
A .... 1......................
A. 3-prong ground plug
B. 3-prong polarized type outdoor outlet
C. Ground prong
Explosion Hazard
Use a new CSA International approved "outdoor"
gas supply line.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 11" (28 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: The installation of this grill must conform with local
codes or, in the absence of local codes, with either the National
Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and Handling
Code, B149.2.
IMPORTANT: Grill must be connected to a regulated gas supply.
Refer to the model/serial rating plate for information on the type
of gas that can be used. If this information does not agree with
the type of gas available, check with your local gas supplier.
Gas Conversion:
No attempt shall be made to convert the grill from the gas
specified on the model/serial rating plate for use with a different
gas type without consulting the serving gas supplier. The
conversion kits specified by the manufacturer must be used.
Gas Pressure Regulator
The gas pressure regulator supplied with this grill must be used.
The inlet (supply) pressure to the regulator should be as follows
for proper operation:
LP Gas:
Set pressure: 11" (27.9 cm) WCP
Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP
Natural Gas:
Set pressure: 4" (10.2 cm) WCP
Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP
maximum.
Contact local gas supplier if you are not sure about the inlet
(supply) pressure.
Burner Requirements for High Altitude
Input ratings shown on the model/serial rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at a
rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice
conversion is required for elevations above 2,000 ft (609.6 m).
See "Assistance or Service" section to order High Altitude
Conversion Kit.
Gas Supply Line Pressure Testing
Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):
The grill and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures greater than 1/2psig (3.5 kPa).
Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WOP (gauge) or
lower:
The grill must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than 1/2psig (3.5 kPa).
Natural Gas
Built-in grill models are equipped for use with Natural gas. They
are design-certified by CSA International for LP (propane) gases
with appropriate conversion.
Built-in models are set for Natural gas use and have a pressure
regulator with 1/2"female pipe threads.
A
, ,//
............................D "C
A. Grill gas pipe
B. New CSA International approved
"outdoor" flexible gas supply line
C. Rear of grifl
D. To Natural gas supply
The supply line shall be equipped with an approved shutoff valve.
This valve should be located in the same area as the grill and
should be in a location that allows ease of opening and closing.
Do not block access to the shutoff valve. The valve is for turning
on or shutting off gas to the grill.
B
A. Gas supply line
B. Shutoff valve "open" position
C. To grifl
LP Gas Conversion Using a Local LP Gas Supply
Conversion must be made by a qualified person. The installation
of this grill must conform with local codes or, in the absence of
local codes, with either the National Fuel Gas Code, ANSI
Z223.1/NPFA 54, Natural Gas and Propane Installation Code,
CSA B149.1, or Propane Storage and Handling Code, B149.2.
To convert to LP gas, the LP Gas Conversion Kit Part Number
W10118099 must be used. Follow instructions included with kit.
A
%IB
............................D
_ C
A. Grifl gas pipe
B. New CSA International approved
"outdoor" flexible gas supply fine
C. Rear of grill
D. To local LP gas supply
LP Gas Conversion Using a 20 Ib LP Gas Fuel Tank
To convert to LP gas, the LP Gas Conversion Kit Part Number
W10118099 must be used. Follow instructions included with kit.
A 20 Ib LP gas fuel tank must be purchased separately.
10
INSTALLATION INSTRUCTIONS
¸G: :iii i
Excessive Weight Hazard
Use two or more people to move and install grill.
Failure to do so can result in back or other injury.
Unpack grill. Remove all packaging materials and remove grill
from carton.
Move grill close to desired outdoor location.
Open the hood.
Remove Packaging Material Inside the Grill
6.
On some models, install rotisserie mounting bracket using
2 screws.
A, 2 screws
B. Rotisserie bracket
7. Dispose of/recycle all packaging material.
NOTE: If grill has been converted to LP gas, follow instructions in
"Conversion to LP Gas" at the end of this section.
1. Cut the tiedowns holding the grates together.
2. Remove rotisserie skewer (on some models), warming shelf
and grill grates from inside the grill and remove packaging
material.
3. Remove foam block and wrap from inside the grill.
A
Fire Hazard
Do not use grill near combustible materials.
Do not store combustible materials near grill.
Doing so can result in death or fire.
.... f
A. Foam block
B. Foam wrap
4. Replace the grill grates.
5. Place warming shelf on brackets as shown.
B
A. Warming shelf brackets
B. Warming shelf
A
Natural Gas Use
The installation of this grill must conform with local codes or, in
the absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and Handling
Code, B149.2.
1. Place grill into outdoor enclosure, but leave enough room in
back to connect to gas supply and electrical plug-in.
Explosion Hazard
Use a new CSA International approved "outdoor"
gas supply line.
Securely tighten all gas connections.
Failure to do so can result in death, explosion, or fire.
2. Make gas connections.
A combination of pipe fittings must be used to connect the
grill to the existing gas line.
11
3.
4.
1.
If local codes permit, use an outdoor flexible stainless
steel tubing gas connector, design-certified by CSA
International, to connect the grill to the rigid gas supply
line. A 5/8"diameter line is recommended. Using a wrench
to tighten, connect the gas supply to the grill. Use pipe-
joint compound on all non-flared male threads. Do not
kink or damage the flexible connector when moving the
grill.
Pipe-joint compounds suitable for use with Natural gas
must be used. Do not use Teflon ®tape.
A
.................................S
............................D ...........C
A. Grifl gas pipe
B. New CSA International approved
"outdoor" flexible gas supply fine
C. Rear of grill
D. To Natural gas supply
Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
A. Closed valve
B. Open valve
Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a
leak. Correct any leak found.
This built-in outdoor grill comes with a 5,000 mAmp power
transformer plug assembly for the grill lights and igniter. Plug
in the single-prong plug in the receptacle on the left
underside of the grill.
A. Single-prong plug
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. Plug into a grounded 3-prong outlet.
3. Gently slide grill completely into outdoor enclosure.
4. Now go to the "Check and Adjust the Burners" section.
".........0 ...............................
IMPORTANT: IfLP gas conversionisdesired,follow
requirements outlined in the "Gas Connection Requirements"
section.
Explosion Hazard
Use a new CSA international approved "outdoor"
gas supply line.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 11" (28 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: A 20 Ib LP gas fuel tank must be purchased
separately.
IMPORTANT: The gas pressure regulator/hose assembly
supplied with the conversion kit must be used. Replacement gas
pressure regulator/hose assembly specific to your model, is
available from your outdoor grill dealer.
12
To Install the 20 Ib LP Gas Fuel Tank:
1. Install the 20 Ib LP gas fuel tank tray according to the
instructions provided with the LP Gas Conversion Kit, Part
Number W10118099.
2. Place the 20 Ib LP gas fuel tank bottom collar into the
mounting hole in the LP tank tray.
3. Tighten the locking screw against the bottom collar of the
20 Ib LP gas fuel tank to secure.
A B
A. Bottom collar
B.Mounting hole
C. Locking screw
4. Screw the gas pressure regulator/hose assembly to the 20 Ib
LP gas fuel tank as shown.
A
A. 20 Ib LP gas fuel tank
B. Gas pressure regulator/hose assembly
5. Turn on the gas supply. Wait a few minutes for gas to move
through the gas line.
6. Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a
leak. Correct any leak found.
7. Go to "Check and Adjust the Burners" section.
The burners are tested and factory-set for most efficient
operation. However, variations in gas supply and other conditions
may make minor adjustments to air shutter or low flame setting
necessary.
It is recommended that a qualified person make burner
adjustments.
NOTE: The rotisserie burner cannot be adjusted.
Checking and adjusting the grill burner flames requires removing
the grate and sear plates.
Burner Flame Characteristics
The flames of the grill burners and side burners (on some models)
should be blue and stable with no excessive noise or lifting (LP
gas flames will have a slightly yellow tip). A yellow flame indicates
not enough air. If flame is noisy or lifts away from the burner, there
is too much air. Some yellow tips on flames when the burner is
set to HI setting are acceptable as long as no carbon or soot
deposits appear.
Check that burners are not blocked by dirt, debris, insect nests,
etc. and clean as necessary. If they are clean, adjust air shutters
as needed.
IMPORTANT: Before adjusting air shutters, let burners cool
completely.
To Adjust:
1. Light grill using information in the "Outdoor Grill Use" section.
2. Observe flame to determine which burners need adjustment
and how the flame is acting.
3. Turn off the valve and wait until grill and burners cool
completely.
4. Remove grill grates and sear plates.
13
5=
Low Flame Adjustment
6=
Remove the 2 screws that hold the burner in place. Remove
gas burner from the grill.
A. 2 screws
If flame is yellow (not enough air), turn air shutter adjustment
screw counterclockwise.
If flame is noisy or lifts away from burner (too much air), turn
air shutter adjustment screw clockwise.
If flame goes out on the "LO" setting, the low flame setting must
be adjusted.
1. Turn off the valve and wait until grill and burners are cool.
2. Remove grill grates and sear plates.
3. Light grill using information in the "Outdoor Grill Use" section.
4. Turn burner to its lowest setting and remove knob.
5. Hold valve stem with pliers and insert a small flat-blade
screwdriver into the shaft.
6. Watch the flame and slowly turn the screwdriver
counterclockwise.
7. Adjust flame to minimum stable flame.
7=
8.
A
A.Air shutter adjustment screw
Adjustment should be made clockwise or counterclockwise
from 1/8"(3.2 mm) to 1/4"(6.4 mm).
Replace gas burner, sear plates and grates.
Light grill using information in the "Outdoor Grill Use" section.
See "Burner Flame Characteristics."
C
A. Valve stem
B. Small flat-blade screwdriver
C. Priers
8. Replace the control knob and turn off the burner.
9. Repeat steps 3 through 8 for each burner if needed.
10. Replace the sear plates and grates after the burners have
cooled.
14
OUTDOOR GRILL USE
This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations and
appearances of the features shown here may not match those of your model.
Control Panel
A B C D E F G H /
ROTISSERIE LEFT CENTER RIGHT SEAR ROTISSERIE FRONT REAR
BURNER BURNER BURNER BURNER BURNER BURNER BURNER BURNER
m-n o
UGH_NGINSTRUC_ONS:
, READINST*UC_ONSe_FOR_U_._Ne
A. Left rotisserie burner control knob
B. Left grill burner control knob
C. Center grill burner control knob
D. Right grifl burner control knob
E.Hood lights switch
F. Sear burner control knob
G. Right rotisserie burner control knob
H. Front side burner control knob
I. Rear side burner control knob
E×plosion Hazard
Do not store fuel tank in a garage or indoors.
Do not store grill with fuel tank in a garage or indoors.
Failure to follow these instructions can result in death,
explosion, or fire.
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
Prepare the Gas Supply
1. Open the hood completely. Do not light burners with the hood
closed.
2. Make sure control knobs are turned to OFE The drip pan
must be in place and pushed all the way to the back.
A
Fire Hazard
Do not use grill near combustible materials.
Do not store combustible materials near grill.
Doing so can result in death or fire.
A. Drip pan
15
Turn the Gas Supply On
1.
For outdoor grills using gas supply source other than 20 Ib LP
gas fuel tank:
Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
4. Guide the lit match between the grill grate and one of the
slots in the sear plate.
A. Closed valve
B. Open valve
2.
For outdoor grills using a 20 Ib LP gas fuel tank:
Slowly open the tank valve.
NOTE: If flow limiting device activates, your grill may not
light. If your grill does light, the flames will be low and will not
heat properly. Turn tank valve and all control knobs off and
wait 30 seconds. After shutting off the tank, very slowly open
tank valve and wait 5 seconds before lighting.
Lighting the Grilland Infrared Sear Burner
IMPORTANT: If burner does not light immediately, turn the
burner knob to OFF and wait 5 minutes before relighting.
1. Do not lean over the grill.
2. Select the burner you want to light. Push in and turn the grill
burner control knob to LITE/HI, while continuing to hold it in.
,,.,=
3. Surface Ignition Type Burners:
You will see the igniter glow. When burner is lit, release the
knob. Turn knob to desired setting.
Spark Ignition Type Burners:
You will hear the "snapping" sound of the spark. When burner
is lit, release the knob. Turn knob to desired setting.
4. Repeat for each of the other burners as needed.
Manually Lighting Main Grill and Infrared Sear Burners
1. Do not lean over the grill.
2. Remove the manual lighting extension (see following
illustration) and attach a match to the split ring.
Right-hand side flange
3. Strike the match to light it.
5. Push in and turn the burner knob to LITE/HI for the burner
closest to the lit match. The burner will light immediately.
When burner is lit, turn knob to desired setting.
m
6. Repeat steps 2 through 5 for each main burner.
7. Remove match and replace manual lighting extension inside
the cabinet drawer.
IM PORTANT:
If burner does not light immediately, turn the burner knob to OFF
and wait 5 minutes before relighting.
If any burners do not light after attempting to light them manually,
contact the KitchenAid Customer eXperience Center. See the
"Assistance or Service" section.
Infrared grilling produces intense heat which quickly sears the
meat. Searing locks in flavor and juices while allowing the outer
surface to absorb smoke and food aroma that is produced as
grease and drippings are vaporized by the burner. The result is a
crisp, flavorful outside with a tender, juicy inside.
Preheat the infrared sear burner for 5 minutes.
Ensure that meats are fully thawed and that all excess fat is
trimmed away prior to grilling.
Leave the burner set to HI when placing food on the grill to
sear.
Use the sear burner to sear meat 1 to 2 minutes on each side,
then move the meat to the main grill cooking surface to finish
grilling to the desired doneness.
NOTE: View is shown with grates removed. Grates are
to be in place when using the infrared sear burner.
16
A
B
A. Rotisserie motor
B. Spit rod
C. Rotisserie fork
D. Rotisserie burner
D
For best cooking results, do not use main grill burners when
using the rotisserie.
The rotisserie system is designed to cook food from the rear
using intense, searing infrared heat.
NOTE: To avoid product damage when not using the rotisserie,
remove motor and store indoors. Remove spit rod and forks.
Store out of reach of children.
To Use:
1. Remove warming shelf,
2. Mount rotisserie motor on the rotisserie's mounting bracket,
Position it securely into support bracket slots. Plug in the
single-prong plug of the 500 mAmp transformer assembly
into rotisserie motor.
B
7. Check that food is centered with the rotisserie burner. If not,
loosen wing nuts, reposition food and retighten wing nuts.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
8. Plug into a grounded 3 prong outlet.
9. Turn on the rotisserie motor and light the rotisserie burner.
See the following "Lighting the Rotisserie Burner" section.
Lighting the Rotisserie Burner
IMPORTANT: If the rotisserie burner does not light immediately,
turn the rotisserie burner knob to OFF and wait 5 minutes before
relighting.
1. Do not lean over the grill.
2. Push in and turn the control knob to LITE/HI.
A
A. Rotisserie motor
B.500 mAmp single-prong power cord
3. To load the spit rod, slide one of the rotisserie forks onto the
spit rod with prongs facing inward.
4. Push spit rod through the center of the food, then slide
second rotisserie fork into position.
5. Center the food and rotisserie forks on spit rod and tighten
wing nuts on the rotisserie forks. If necessary, secure loose
food portions with butcher's string.
6. Once the food is positioned on spit rod, place pointed end of
rod through the hole in the left side of the grill and into the
rotisserie motor, then lower the notched end of the spit rod
onto the support bracket on the opposite side.
A.Pointed end of spit rod
B.Notched end of spit rod
m
l
Surface Ignition Type Burners:
You will see the igniter glow.
Spark Ignition Type Burners:
Your will hear the "snapping" sound of the spark.
3. When the rotisserie burner lights, continue to hold the knob in
for another 10 seconds, then release the knob and burner will
stay lit.
Manually Lighting the Rotisserie Burner
IMPORTANT: If the rotisserie burner does not light immediately,
turn the rotisserie burner knob to OFF and wait 5 minutes before
relighting.
1. Do not lean over the grill.
17
2.
3.
4.
Remove the manual lighting extension (see following
illustration) and attach a match to the split ring.
Right-hand side flange
Strike the match to light it.
Gently hold the lit match close to the rotisserie burner.
B
5.
A. Lighting extension
B. Rotisserie burner
Push in and turn the control knob to LITE/HI. Hold this knob
in for 10 seconds after the burner is lit.
6.
,,.,=
Surface Ignition Type Burners:
You will see the igniter glow until after the knob is released.
Spark Ignition Type Burners:
You will hear the "snapping" sound of the spark until after the
knob is released.
Remove the match and replace the manual lighting extension
inside the cabinet drawer.
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
Rotisserie cooking rotates food in front of the rotisserie burner,
creating an intense heat for searing the outside and sealing in
natural juices.
The rotisserie burner reaches cooking temperatures in about
1 minute. It is not necessary to preheat when using the rotisserie.
Select tender meat and poultry.
Allow at least 1" (2.5 cm) space between rotisserie burner
and the food.
To make cleanup easier, place a pan under the food to catch
drippings.
The hood can be opened or closed, but when using the
rotisserie with the smoker the hood should be closed.
Add barbecue sauce or glaze only during the last 10 minutes
of cooking to keep sauce from burning.
Trussing Poultry for the Rotisserie
1. Load the spit rod by sliding one of the forks on the rod, with
the prongs facing inward. Tighten the screw to keep it from
slipping.
2. Push the rod through the center of the bird.
3. Cut 24" (61 cm) of butcher's string and center it under the
bird, breast side up.
4. Wrap each end of the string around the wings; catch each
wing tip. Bring the string tightly together at the top of the
breast and knot. It is not necessary to cut off the extra string.
5. Cut another 20" (50.8 cm) of string and lay it under the back
of the bird. Wrap it around the tail then around the spit rod,
cinching tightly.
6. Cross the legs on top of spit rod; tie string around the
crossed legs.
7. Connect the twine holding the legs, to the string holding the
wings, and knot. Cut off any bits of hanging string.
8. Slide on the second fork pushing the tines into the
drumsticks.
9. Center the food and forks on the rod and tighten the thumb-
screws. The bird should be firmly in place on the rotisserie
spit rod.
ROTISSERIE CHART
Use a portable meat thermometer to check internal doneness of
the food.
Turn off rotisserie burner when meat thermometer reads 5°F/3°C
lower than desired internal temperature. Continue rotating, hood
closed, for 10 minutes before carving.
Timing is affected by weather conditions such as wind and
outside temperature.
Food Weight Internal Approximate
Doneness or Grilling Time
Temperature (min/Ib)
(°F/°C)
Beef
Roasts 4-6 Ibs Medium-rare 15-20
Rib Eye 1.5-2.2 kg (145°F/63°C)
Sirloin Tip Medium 20-25
Rib, boneless (160°F/71 °C)
Poultry
Chicken 3-6 Ibs Breast 25-30
1.1-2.2 kg (170°F/77°C)
Thigh 25-30
(180°F/82°C)
Turkey, whole 7-10 Ibs Breast 11-20
2.6-3.7 kg (170°F/77°C)
Thigh 11-20
(180°F/82°C)
18
Food Weight Internal Approximate
Doneness or Grilling Time
Temperature (min/Ib)
(°F/°C)
Lamb
Boneless leg 4-7 Ibs Medium 20-25
1.5-2.6 kg (160°F/71°C)
Pork
Loin roast, 4-6 Ibs Medium 20-23
boneless 1.5-2.2 kg (160°F/71°C)
% #
&J
The smoker box can be used when grilling or when using your
rotisserie.
1. Prepare wood chips/pellets following manufacturer's
directions.
2. Open smoker box lid and add prepared chips/pellets onto the
grate inside the smoker box.
NOTE: For about 1 hour of smoking, fill the smoker box
approximately one-fourth full of chips/pellets.
3. Remove the small grate from the grill and replace with the
smoker box.
A
B
!
A. Shown with smafl grate removed
B. Smoker box
4. Light the burner below the smoker box and preheat on high
until smoker begins smoking. Reduce the heat setting to
keep the smoke at the amount desired.
To Refill the Smoker Box During Use
IMPORTANT: You may want to wear oven mitts when opening
and closing the smoker box lid.
1. Open grill hood.
2. Lift smoker box lid and add more prepared chips/pellets.
3. Close the smoker box lid.
4. Close the grill hood and continue grilling.
*See "Assistance or Service" section to order.
TIPS FOR OUTDOOR
GRILLING
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
Before Grilling
Thaw food items before grilling.
Preheat grill on high (use all grill burners) 10 minutes. The
hood must be closed during preheating. There is no need to
use the back rotisserie burner for preheating. Preheating
provides the high heat needed to brown and seal the juices.
Shorten the preheat time when grilling high-fat cuts of meat
or poultry, such as chicken thighs. This will help reduce
flare-ups.
Lightly oil the grill grates or the food when cooking low-fat
cuts of meat, fish or poultry, such as lean hamburger patties,
shrimp or skinless chicken breasts.
Using too much oil can cause gray ash to deposit on food.
Trim excess fat from meats prior to cooking to reduce
flare-ups.
Make vertical cuts at 2" (5 cm) intervals around the fat edge
of meat to avoid curling.
Add seasoning or salt only after the cooking is finished.
During Grilling
Turn foods only once. Juices are lost when meat is turned
several times.
Turn meat just when juices begin to appear on the surface.
Avoid puncturing or cutting the meats to test doneness. This
allows juices to escape.
It may be necessary to lower the heat setting for foods that
cook a long time or are marinated or basted in a sugary
sauce.
If using a high flame, add barbecue sauce only during the last
10 minutes of cooking to avoid burning the sauce.
The degree of doneness is influenced by the type of meat, cut
of meat (size, shape and thickness), heat setting selected,
and length of time on the grill.
Cooking time will be longer with an open grill cover.
The 5,000 mAmp power transformer must be plugged in for the
hood lights to work. See "Plug in Grill" in the "Installation
Instructions" section.
To Use:
Press the LIGHTS button on the control panel to turn the hood
lights on and off.
19
For optimal use of the SureSear TM system, the following cooking
methods are recommended.
Direct Heat
Cooking by direct heat means the food is placed on grill grates
directly above lighted burners. Hood position can be up or down.
If hood is in the up position, total cooking times may be longer.
Direct heat sears the food. Searing is a process that seals natural
juices in food by cooking with intense heat for a short period of
time. While juices stay inside, the outside is browned with a
flavorful grilled coating.
Indirect Heat
For best results, do not select the indirect heat cooking method
when it is windy.
Cooking by indirect heat means the food is placed on the grill
grate above an unheated burner, allowing heat from lighted
burner(s) on either side to cook the food.
If possible, turn on 2 burners. Cook with the hood down. This will
shorten the cooking time.
Indirect Cooking
Place food only on the grill grate over the OFF burners.
Grill Size Burner Burner Burner Burner
1 2 3 4
27" (68.6 cm) ON OFF
36" (91.4 cm) ON OFF ON
48" (121.9 cm) ON OFF ON OFF
Knobs have High, Medium and Low settings for flame
adjustment.
Heat settings indicated are approximate.
Grilling times are affected by weather conditions.
When 2 temperatures are listed, for example: Medium to
Medium-Low, start with the first and adjust based on cooking
progress.
Cooking times may vary from chart times depending on the
type of fuel, Natural or LP gas.
FOOD COOKING METHOD/ INTERNAL TEMP. TIME SPECIAL INSTRUCTIONS
BURNER SETTING (total minutes)
Beef
Hamburgers 1/2"(1.3 cm) to
3A"(1.9 cm) thick
Roasts
Rib Eye, Sirloin
Steaks, 1" (2.5 cm)
Porterhouse, Rib, T-bone,
Top Loin, Sirloin
Steaks, 11/2"(3.8 cm)
Porterhouse, Rib, T-bone,
Top Loin, Sirloin
Top Round or Shoulder/
Chuck (London Broil)
11/2"(3.8 cm) thick
Flank, 1/2"(1.3 cm) thick
DIRECT
Medium
INDIRECT
Medium/OFF/Medium
DIRECT
Medium
DIRECT
Medium
DIRECT
Medium
DIRECT
Medium
Medium (160°F/71°C)
Med-Rare (145°F/63°C)
to Medium (160°F/71°C)
Med-Rare (145°F/63°C)
to Medium (160°F/71°C)
Med-Rare (145°F/63°C)
to Medium (160°F/71°C)
Med-Rare (145°F/63°C)
to Medium (160°F/71°C)
Med-Rare (145°F/63°C)
10-15
32-40 per Ib
(12-15 per kg)
11-16
18-25
22-29
11-16
Grill, turning once.
Tent with foil first 45-60 minutes
of cooking time.
Rotate steaks turn to create
criss-cross grill marks.
Pork
Chops,
1" (2.5 cm)
11/2"(3.8 cm) thick
Ribs
21/2-4Ibs (0.9-1.5 kg)
Roast, boneless tenderloin,
1 Ib (0.37 kg)
Ham half,
8-10 Ibs (3-3.7 kg)
DIRECT
Medium to Med-Low
INDIRECT
Med/OFF/Med
DIRECT
Medium
INDIRECT
Med/OFF/Med
Medium (160°F/71°C)
Medium (160°F/71°C)
Medium (160°F/71°C)
Reheat (140°F/60°C)
12-22
30-40
40-60
18-22
2-21/2hours
Grill, turning occasionally.
During last few minutes brush
with barbecue sauce if desired.
When done, wrap in foil.
Turn during cooking to brown
on all sides.
Wrap entire ham in foil and put
on grill without pan or drip pan.
Ham steak precooked,
1/2"(1.3 cm) thick
Hot Dogs
DIRECT
Preheat Medium
Grill Medium
DIRECT
Medium
Reheat (145°F/63°C)
Reheat (145°F/63°C)
7-10
5-10 Slit skin if desired.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

KitchenAid KBSS271TSS00 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues