Lynx LM24REFL Manuel utilisateur

MAKE THE MOST OF YOUR

CARE & USE/INSTALLATION

LM15REF / LM24REF

OUTDOOR REFRIGERATOR

2

CARE AND USE/INSTALLATION

NOTE

!

CAUTION

CONTENTS AND SAFETY INSTRUCTIONS

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product Dimensions ...........................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................10

Refrigerator operation ...................................................10

Alarms ............................................................................10

Door ajar ...................................................................10

Temperature sensor fault ..........................................10

High and Low temperature .......................................10

Alarm mute ..................................................................11

Shelving congurations .....................................................11

Care and cleaning .............................................................13

Long term storage / winterization ................................ 14

Stainless steel maintenance ............................................15

Energy saving tips ............................................................16

Obtaining service .............................................................16

Troubleshooting ................................................................17

The Lynx story ...................................................................18

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Important Safety Instructions

Contents

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

3

CARE AND USE/INSTALLATION

NOTE

!

CAUTION

UNPACKING YOUR APPLIANCE

Warranty Registration

Remove Interior Packaging

XXXXXXXXXXXXXX

XXXXXXXXXXXX

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at:

www.lynxgrills.com/support/registration

The following information will be required when registering

your appliance.

Service/Model Number

Serial Number

Date of Purchase

Dealer’s name and address

The service/model number and serial number can be found

on the serial plate which is located inside the cabinet on

the left side near the top. (See Figure 1).

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

4

CARE AND USE/INSTALLATION

!

CAUTION

Leveling Legs

Select Location

Cabinet Clearance

Front Grille

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 115°F (13 to 46°C).

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Lynx Grills does not recommend the

use of a custom made grille as air ow may be restricted.

(See Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Lynx appliance may be adjusted between

the minimum, 33

3

⁄4" (85.7 cm), by turning the leveling leg in

(CW ↷) and the maximum, 34

3

⁄4" (88.3 cm) by turning the

leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

5

CARE AND USE/INSTALLATION

NOTE

Figure 6

Electrical Connection

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Front grille screw

Front grille

Figure 5

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

6

CARE AND USE/INSTALLATION

INSTALLING THE ANTI TIP DEVICE (FREESTANDING INSTALLATIONS)

!

CAUTION

NOTE

Bottom View of

Refrigerator

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

21

1

⁄2"

(54.6 cm)

Figure 7

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the refrigerator as shown in Figure 7.

for locating the position of the bracket:

1) Decide where you want to place the refrigerator. Slide it

into place, being careful not to damage the oor, leaving 1"

(2.5 cm) of clearance from the rear wall to allow room for

the anti-tip bracket.

2) Raise the rear leveling legs approximately

1

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the refrigerator is in the desired location, then

mark on the oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the oor marking the front corner

of the cabinet, excluding the door. Slide the refrigerator out

of the way. From the temporary line extend the sidewall line

back 21

1

⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

1

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

!

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

!

WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

Anti-Tip Device

Floor Mount Installation

Step by Step Instructions

7

CARE AND USE/INSTALLATION

INSTALLING THE ANTI TIP DEVICE (FREESTANDING INSTALLATIONS)

21

1

⁄2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Side of cabinet line

Figure 8

Front of cabinet line

Rear of cabinet line

Rear Leveling leg

Screw

Figure 8a

NOTE

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

3

⁄8" (9 mm).

8

CARE AND USE/INSTALLATION

MODEL

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

"A" "B" "C" "D" "E" "F" "G" "H" "J"

LM15REF

15"

(38.1 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

14

7

⁄8"

(37.8 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

3

⁄4"

(67.9 cm)

37

13

⁄32"

(95 cm)

17

3

⁄4"

(45.1 cm)

LM24REF

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

3

⁄4"

(67.9 cm)

46

13

⁄32"

(117.9 cm)

26

3

⁄4"

(67.9 cm)

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

PRODUCT DIMENSIONS

Figure 9

Figure 9a

Figure 10

9

CARE AND USE/INSTALLATION

"F"

21

1

⁄2"

(54.6 cm)

* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

MODEL

PRODUCT DATA

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

LM15REF 115V/60Hz/15A

105 lbs

(47.7 kg)

LM24REF 115V/60Hz/15A

140 lbs

(63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 11

!

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

10

CARE AND USE/INSTALLATION

USING YOUR ELECTRONIC CONTROL

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

F

Figure 12

close-up of

control

• Temperature Sensor Fault: If the control-

ler detects that the temperature sensor is

not properly functioning, a temperature

sensor alarm will sound in one (1) second intervals. "E1"

will ash on the display panel and the Alarm LED located at

the top left of the display below the word "Alarm" will be il-

luminated. Please call Lynx Grills Customer Service or your

dealer if this error code is displayed.

• High and Low Temperature Alarm: If the

storage compartment temperature deviates

excessively from the set-point temperature, the

alarm will sound in (1) second intervals. The

display panel will ash either "Hi" or "Lo" de-

pending upon the condition and the Alarm LED

light at the top left of the display below the word

"Alarm" will be illuminated. The alarm will remain active

until the condition is corrected.

Your electronic control will monitor refrigerator function and

alert you with a series of audible and visual alarms.

• Door Ajar Alarm: If the door has been left

open for over ve (5) minutes, the alarm

will sound in one (1) second intervals. The

display panel will ash "do" and the Alarm LED located at

the top left of the display below the word "Alarm" will be il-

luminated. This will stop as soon as the door is closed.

Figure 13

LM15REF shown

Starting Your Refrigerator

Turning Your Refrigerator ON or OFF

Set temperature

Refrigerator Operation

Alarms

Plug the refrigerator power cord into a wall outlet. Your

refrigerator will begin cooling after power is applied.

If your refrigerator does not start, check that the refrigerator

is turned on and the set temperature is cold enough.

If the refrigerator is on, the refrigerator temperature will be

shown on the display. To turn the refrigerator off, press and

hold the "ON/OFF" button for three (3) seconds. "OFF" will

appear on the display.

If the refrigerator is not on, "OFF" will be shown on the

display. To turn the refrigerator on, press and hold the "ON/

OFF" button for three (3) seconds. The refrigerator tem-

perature will be shown on the display.

To set the refrigerator temperature, press and hold the

"SET" button. When the "SET" button is pressed, the

display will show the set temperature. While holding the

"SET" button, press the "WARMER" or "COLDER" buttons

to adjust set temperature.

The available temperature range of the refrigerator is 34° to

42°F (1° to 6° C).

It may take up to 24 hours for your refrigerator to reach

desired temperature. This will depend on amount of content

loaded and number of door opening and closings.

For best results allow refrigerator to "pull down" to desired

set temperature before loading. Once contents are loaded,

allow at least 48 hours for temperature to stabilize before

making any adjustments to the set temperature.

11

CARE AND USE/INSTALLATION

Figure 14

Figure17

SHELVING CONFIGURATIONS

Refrigerator:

Your appliance is equipped with a cantilever shelf system

which provides maximum adjust ability and customizing of

the shelving arrangements listed below.

15" (38.1 cm) Wide Models:

Wiith a solid door. Figure 14.

(2) perforated stainless

steel slide out shelves.

(See Figure 15).

(1) 3 bottle wine shelf

(see Figure 16).

(2) perforated metal

cantilever shelves.

(See Figure 18).

24" (61 cm) Wide Models:

With a solid door. Figure17.

Figure 15

perforated metal

shelf

Figure 18

Perforated metal shelf

NOTE

Press any key to mute the audible portion of an alarm.

This action will only mute the alarm. If the condition that

caused the alarm continues, the alarm code will continue to

ash and will sound for 20 seconds every 60 minutes.

Alarm Mute

Loading Tips and Suggestions

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

Figure 16

Wine shelf, 3 bottle

12

CARE AND USE/INSTALLATION

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

19). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

!

CAUTION

Grasp the shelf by the front with

both hands and rotate the front

of the shelf up, then lift the shelf

up and remove the shelf from the

shelf ladders.

!

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

SHELVING CONFIGURATIONS

Figure 19a

Figure 19

To Add or Remove a Shelf

13

CARE AND USE/INSTALLATION

CARE AND CLEANING

!

CAUTION

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

!

WARNING

Electrocution Hazard

Front Grille

Cabinet

Interior

Care of Appliance

In the Event of a Power Failure

Light Assembly Replacement

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

The stainless steel cabinet can be washed with either a

mild soap and water and thoroughly rinsed with clear water.

See "Stainless Steel Maintenance" on page 15.

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

14

CARE AND USE/INSTALLATION

CARE AND CLEANING

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

!

CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

2. Turn unit off, (see page 10)

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be

turned-off if the circuit is not required for other items

during the Winter season.

7. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

8. Remove the front toe-grille, (see Figure 20), and use a

brush and vacuum to clean dirt and debris from be-

neath the unit.

9. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 20).

10. Remove the rear access cover, (see Figure 21), and

use a brush and vacuum to clean dirt and debris from

the machine compartment.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the door open and allow to completely dry out

before closing the door.

14. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 15.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

1. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

2. Connect the unit to electrical power.

3. Turn unit on and conrm your desired control settings.

4. Allow 24-hrs for the unit to stabilize before loading

contents.

Figure 20

Grille

Spacer

Clean out

behind

grille

Figure 21

Soak up

water from

plastic drain

pan if

necessary

Clean out

debris

Remove screws

around perimeter

of access cover.

18. Do not place a cover on the unit, as this can trap con-

densation.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove screw from

each end of grille

Access cover

Long Term Storage/Winterization

Start-up after Long Term Storage

15

CARE AND USE/INSTALLATION

STAINLESS STEEL MAINTENANCE

NOTE

Background

Care and Cleaning

Choosing a Cleaning Product

Stainless steel does not stain, corrode, or rust as easily as

ordinary steel, but it is not stain or corrosion proof. Stain-

less steels can discolor or corrode if not maintained prop-

erly.

Stainless steels differ from ordinary carbon steels by the

amount of chromium present. It is this chromium that

provides an invisible protective lm on the surface called

chrome-oxide. This protective chrome-oxide lm on the

surface can be damaged or contaminated, which may

result in discoloration, staining, or corrosion of the base

metal.

Routine cleaning of the stainless steel surfaces will serve to

greatly extend the life of your product by removing contami-

nants. This is especially important in coastal areas which

can expose the stainless to severe contaminants such as

halide salts, (sodium chloride).

It is strongly recommended to periodically inspect and thor-

oughly clean crevices, weld points, under gaskets, rivets,

bolt heads, and any locations where small amounts of liquid

could collect, become stagnant, and concentrate contami-

nates. Additionally, any mounting hardware that is showing

signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

location, environmental, and usage conditions.

The choice of a proper cleaning product is ultimately that

of the consumer, and there are many products from which

to choose. Depending upon the type of cleaning and the

degree of contamination, some products are better than

others.

Typically the most effective and efcient means for routine

cleaning of most stainless steel products is to give the sur-

faces a brisk rubbing with a soft cloth soaked in warm water

and a gentle detergent, or mild mixture of ammonia. Rub-

bing should, to the extent possible, follow the polish lines of

the steel, and always insure thorough rinsing after cleaning.

Although some products are called "stainless steel clean-

ers," some may contain abrasives which could scratch the

surface, (compromising the protective chrome-oxide lm),

and some many contain chlorine bleach which will dull,

tarnish or discolor the surface if not completely removed.

After the stainless surfaces have been thoroughly cleaned,

a good quality car wax may be applied to help maintain the

nish.

Stainless steel products should never be installed, or stored

in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used

in strict accordance with the instructions of the cleaner

manufacturer.

16

CARE AND USE/INSTALLATION

ENERGY SAVING TIPS AND OBTAINING SERVICE

If Service is Required:

• If the product is within the rst year warranty period

please contact your dealer or call Lynx Grills Customer

Service at 888.289.5969 for directions on how to obtain

warranty coverage in your area.

• If the product is outside the rst year warranty period,

Lynx Grills Customer Service can provide recommen-

dations of service centers in your area.

• In all correspondence regarding service, be sure to give

the service/model number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service/Model Number

Date Warranty Card Sent (Must be

within 10 days of purchase).

Table A

The following suggestions will minimize the cost of

operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

Energy Saving Tips

17

CARE AND USE/INSTALLATION

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

!

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read through

this manual rst. If the problem persists, check the trouble-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required

to contact your dealer or a qualied service technician.

TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See “Adjusting the temperature" on

page 10)

• Control set too warm

• Content temperature not stabi-

lized.

• Excessive usage or prolonged

door openings.

• Airow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Al-

low 24 hours for temperature to

stabilize.

• Allow temperature to stabilize for

at least 24 hours.

• Airow must not be obstructed to

front grille. See “clearances” on

page 4.

• Replace door gasket.

Appliance too cold

(See “Adjusting the Temperature” on

page 10)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Replace door gasket.

No interior light. • Failed LED light assembly or light

switch.

• Contact a qualied service techni-

cian.

Light will not go out when door is

closed

• Display light is turned on. (Glass

door models only.

• Door not activating light switch.

• Failed light switch

• Turn off display light, shut door.

• Appliance not level, level appli-

ance, (See page 4, “leveling legs”)

• Contact a qualied service techni-

cian.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see “Leveling

Legs” on page 4.

• Contact a qualied service techni-

cian.

Appliance will not run. • Appliance turned off

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting

your appliance” on page 10.

• Plug in power cord.

• Check house circuit.

!

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a qualied service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit off without appropriately

managing the excess water run-off.

18

CARE AND USE/INSTALLATION

THE LYNX STORY

Lynx began with a vision.

A small group of manufacturing engineers with over a cen-

tury of collective experience had a dream. They dared to

take their extensive commercial manufacturing know-how

and create a line of outdoor cooking products that offer com-

mercial elegance and performance to the consumer market.

Lynx has taken the quality, work-

manship, service and innovation of

the commercial market and incor-

porated it into the Lynx Professional

Grills line of consumer and com-

mercial products. The combination

of creative design, superior materi-

als and exceptional craftsmanship

elevates Lynx products to a class of

their own.

Lynx original commercial products are used every day in

restaurants, hotels and theme parks across the USA:

Lynx Satised Customers

• TGI Fridays

• Applebee’s

• Houston’s

• Red Lobster

• Hard Rock Café

• Wolfgang Puck’s

• Cheesecake Factory

• Red Robin

• Planet Hollywood

• Hilton

• Hyatt

• Four Seasons Marriott

Le Meridian

• Sheraton

• Conrad International

• Bellagio

• New York New York

• MGM Grand

• Treasure Island

• Mirage

• Paris

• Venetian

• Excalibur

• Mandalay Bay

• Riviera

• Desert Inn

• Hard Rock Hotel

• Disney World

19

CARE AND USE/INSTALLATION

All specications and product designs subject to change without notice. Such revisions do not entitle

the buyer to corresponding changes, improvements, additions, replacements or compensation for

previously purchased products.

41014708-EN Rev A

1/30/17

The best outdoor kitchen products come from:

Lynx Grills, Inc. 7300 Flores Street Downey, CA 90242

Service: (888)-289-5969 Fax: (562) 299-6789

www.lynxgrills.com

La page charge ...

Lynx LM24REFL Manuel utilisateur

Ce manuel convient également à

Lynx LM24REFL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents