Tunturi T35 Le manuel du propriétaire

Taper
Le manuel du propriétaire
www.tunturi.com
Attention, Achtung, Attention, Attentie, Attenzione, Atención, Giv akt, Huomio
- Please read this Owner’s manual before assembling this product.
- Bitte lesen Sie dieses Handbuch durch, bevor Sie mit er Montage dieses Produkts beginnen.
- Veuillez lire ce manuel avant de commencer le montage de ce produit.
- Leest u deze handleiding voordat u dit apparaat installeert.
- Leggere questo manuale prima di assemblare questo prodotto.
- Lea este manual antes de montar este producto
- Läs bruksanvisningen innan du monterar denna produkt
- Lue tämä käsikirja ennen kokoamista tuotetta
WWW
Cardio Fit T35
GB User manual 14 - 20
DE Benutzerhandbuch 21 - 28
FR Manuel de l’utilisateur 29 - 36
NL Gebruikershandleiding 37 - 44
IT Manuale d‘uso 45 - 52
ES Manual del usuario 53 - 60
SV Bruksanvisning 61 - 67
SU Käyttöohje 68 - 74
3
Cardio Fit T35
A
i
100 cm
100 cm
100 cm
100 cm
4
Cardio Fit T35
B
C
X
Hexagon socket
large at head
half tooth bolt
Hexagon socket
short at head
full tooth bolt
2x
4x
5
Cardio Fit T35
C-1
Hexagon socket
large at head
half tooth bolt
Hexagon socket
short at head
full tooth bolt
2x
4x
6
Cardio Fit T35
C-2
Hexagon socket
large at head
half tooth bolt
Hexagon socket
short at head
full tooth bolt
2x
4x
7
Cardio Fit T35
C-3
A
B
||
3 4 5 6
M
_
P
_
_
7 8 9 10
PAUZE
START
PROGRAM
MODE
STOP
Read the owner’s manual carefully
before using the prouct.
Remove the safety key when the
unit is not in use.
To avoid injury, stand on the side
rails before starting the unit.
Keep childeren away from the
treadmill during operation.
WARNING
AUTO SLEEP FUNCTION
QUICK
SPEED
Note that this treadmill is fitted
witn an auto sleep function.
If treadmill is not used for 4:30
minutes, the computer will
automatically turn in sleep mode.
Press any key to restart console.
Your data will be retained.
8
Cardio Fit T35
E-1
E-2
9
Cardio Fit T35
F-1
F-2
10
Cardio Fit T35
F-3
F-4
11
Cardio Fit T35
F-5
F-6
12
Cardio Fit T35
F-7
F-8
13
Cardio Fit T35
G
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
P1 SPEED
1 3 3 7 7 5 5 5 7 7 5 5 5 5 3 2
P2 SPEED
2 3 3 6 5 5 8 5 5 6 8 8 8 5 4 3
P3 SPEED
2 3 5 5 7 7 8 5 5 6 8 8 8 5 4 3
P4 SPEED
2 2 3 5 5 5 8 8 8 8 5 5 5 3 3 2
P5 SPEED
3 4 5 6 7 8 9 10 10 10 9 8 7 5 4 3
P6 SPEED
3 4 5 5 6 6 7 7 7 9 9 10 10 11 5 3
P7 SPEED
3 4 9 4 11 4 10 4 9 4 8 4 11 5 3 2
P8 SPEED
3 5 8 3 5 7 9 3 5 7 10 3 5 7 11 5
P9 SPEED
3 7 9 4 7 10 4 7 11 5 7 12 4 7 12 6
P10 SPEED
3 5 6 6 6 9 10 6 6 9 10 6 6 6 11 3
P11 SPEED
4 5 7 9 10 11 9 6 8 9 10 10 11 9 6 5
P12 SPEED
4 6 10 10 7 10 10 10 7 7 10 10 10 10 6 5
P13 SPEED
4 12 4 12 4 12 4 12 4 12 4 12 4 12 4 12
P14 SPEED
2 3 3 6 9 11 3 6 9 11 3 6 9 11 3 6
P15 SPEED
4 6 11 11 9 6 11 11 9 6 11 11 9 6 11 11
P16 SPEED
2 4 4 12 4 12 4 12 4 12 4 12 4 12 4 12
P17 SPEED
2 2 2 4 6 6 9 11 11 2 4 6 6 11 11 9
P18 SPEED
3 6 3 6 6 3 6 6 3 6 6 3 6 6 3 6
P19 SPEED
4 12 4 12 4 12 4 12 4 12 4 12 4 12 4 12
P20 SPEED
5 13 5 13 5 13 5 13 5 13 5 13 5 13 5 13
P21 SPEED
2 6 2 6 11 2 6 11 2 6 11 2 6 11 2 6
P22 SPEED
4 6 11 6 2 11 6 2 11 6 2 11 6 2 11 6
P23 SPEED
4 6 11 6 6 2 11 6 6 2 11 6 6 2 11 6
P24 SPEED
4 6 11 6 4 11 6 4 11 6 4 11 6 4 11 6
P25 SPEED
5 13 5 13 5 13 5 13 5 13 5 13 5 13 5 13
P26 SPEED
3 4 4 7 10 12 4 7 10 12 4 7 10 12 4 7
P27 SPEED
5 7 12 12 10 7 12 12 10 7 12 12 10 7 12 12
P28 SPEED
3 5 5 13 5 13 5 13 5 13 5 13 5 13 5 13
P29 SPEED
3 3 3 5 7 7 10 12 12 3 5 7 7 12 12 10
P30 SPEED
4 7 4 7 7 4 7 7 4 7 7 4 7 7 4 7
P31 SPEED
5 13 5 13 5 13 5 13 5 13 5 13 5 13 5 13
P32 SPEED
6 14 6 14 6 14 6 14 6 14 6 14 6 14 6 14
P33 SPEED
3 7 3 7 12 3 7 12 3 7 12 7 7 12 3 7
P34 SPEED
5 7 12 7 3 12 7 3 12 7 3 12 7 3 12 7
P35 SPEED
5 7 12 7 7 3 12 7 7 3 12 7 7 3 12 7
P36 SPEED
5 7 12 7 5 12 7 5 12 7 5 12 7 5 12 7
14
English
Index
Treadmill �������������������������������������������������������������������������� 14
Safety warnings ��������������������������������������������������������������� 14
Electrical safety ��������������������������������������������������������������������������������14
Assembly instructions ������������������������������������������������������ 15
Description (g. A) ���������������������������������������������������������������������������15
Package contents (g. B ) ����������������������������������������������������������������� 15
Assembly (g. C) ������������������������������������������������������������������������������15
Workouts ������������������������������������������������������������������������������������������15
Exercise Instructions �������������������������������������������������������������������������15
Heart rate �����������������������������������������������������������������������������������������16
Use����������������������������������������������������������������������������������� 16
Console (g. E-1) ������������������������������������������������������������� 17
Buttons ���������������������������������������������������������������������������������������������17
Explanation of display items ������������������������������������������������������������17
Programs ������������������������������������������������������������������������ 17
Quick start ����������������������������������������������������������������������������������������17
Countdown mode ����������������������������������������������������������������������������17
End your workout �����������������������������������������������������������������������������17
Preset Programs (P1~P36) ���������������������������������������������������������������� 17
Body Fat �������������������������������������������������������������������������������������������17
Warranty �������������������������������������������������������������������������� 18
Cleaning and maintenance ����������������������������������������������� 18
Belt and Running Deck ��������������������������������������������������������������������18
Lubrication (g. F-4) �������������������������������������������������������������������������19
Troubleshooting �������������������������������������������������������������� 19
Transport and storage ����������������������������������������������������� 20
Additional information ���������������������������������������������������������������������20
Technical data ������������������������������������������������������������������ 20
Declaration of the manufacturer ������������������������������������� 20
Disclaimer ������������������������������������������������������������������������ 20
- The equipment is suitable for domestic use only� The equipment is
not suitable for commercial use�
- Max� usage is limited to 2 hrs a day
- The use of this equipment by children or persons with a physical,
sensory, mental or motorial disability, or lack of experience and
knowledge can give cause to hazards. Persons responsible for their
safety must give explicit instructions or supervise the use of the
equipment�
- Before starting your workout, consult a physician to check your
health�
- If you experience nausea, dizziness or other abnormal symptoms,
immediately stop your workout and consult a physician.
- To avoid muscular pain and strain, start each workout by warming
up and finish each workout by cooling down. Remember to stretch
at the end of the workout.
- The equipment is suitable for indoor use only� The equipment is
not suitable for outdoor use�
- Only use the equipment in environments with adequate ventilation.
Do not use the equipment in draughty environments in order not
to catch a cold�
- Only use the equipment in environments with ambient
temperatures between 10 °C and 35 °C. Only store the equipment
in environments with ambient temperatures between 5 °C and 45
°C.
- Do not use or store the equipment in humid surroundings� The air
humidity must never be more than 80%�
- Only use the equipment for its intended purpose� Do not use the
equipment for other purposes than described in the manual�
- Do not use the equipment if any part is damaged or defective� If a
part is damaged or defective, contact your dealer.
- Keep your hands, feet and other body parts away from the moving
parts�
- Keep your hair away from the moving parts.
- Wear appropriate clothing and shoes�
- Keep clothing, jewelry and other objects away from the moving
parts�
- Make sure that only one person uses the equipment at a time�
The equipment must not be used by persons weighing more than
100kg (220 lbs).
- Do not open equipment without consulting your dealer.
Electrical safety
(Only for equipment with electric power)
- Before use, always check that the mains voltage is the same as the
voltage on the rating plate of the equipment�
- Do not use an extension cable�
- Keep the mains cable away from heat, oil and sharp edges.
- Do not alter or modify the mains cable or the mains plug�
- Do not use the equipment if the mains cable or the mains plug
is damaged or defective� If the mains cable or the mains plug is
damaged or defective, contact your dealer.
- Always fully unwind the mains cable.
- Do not run the mains cable underneath the equipment� Do not run
the mains cable underneath a carpet� Do not place any objects on
the mains cable�
- Make sure that the mains cable does not hang over the edge of a
table�
- Make sure that the mains cable cannot be caught accidentally or
tripped over
- Do not leave the equipment unattended when the mains plug is
inserted into the wall socket.
- Do not pull the mains cable to remove the mains plug from the wall
socket�
- Remove the mains plug from the wall socket when the equipment
is not in use, before assembly or disassembly and before cleaning
and maintenance�
Treadmill
Welcome to the world of Tunturi!
Thank you for purchasing this piece of Tunturi equipment�
Tunturi offers a wide range of home fitness equipment, including
crosstrainers, treadmills, exercise bikes and rowers. The Tunturi
equipment is suitable for the entire family, no matter what fitness
level. For more information, please visit our website
www.tunturi.com
Important Safety Instructions
This Owner’s Manual is an essential part of your training equipment:
reading all instructions in this manual before you start using this
appliance. The following precautions must always be followed:
Safety warnings
⚠ WARNING
Read the safety warnings and the instructions. Failure to follow
the safety warnings and the instructions can cause personal
injury or damage to the equipment. Keep the safety warnings
and the instructions for future reference�
⚠ WARNING
Heart rate monitoring systems may be inaccurate� Over exercise
may result in serious injury or death� If you feel faint stop
exercising immediately
15
English
⚠ CAUTION
If voltage varies by ten percent (10%) or more, the performance
of your treadmill may be affected� Such conditions are not
covered under your warranty. If you suspect the voltage is low,
contact your local power company or a licensed electrician for
proper testing�
⚠ CAUTION
Route the power mains cord away from any moving part of
the treadmill including the elevation mechanism and transport
wheels.
Grounding Instructions
This product must be grounded� If the treadmill’s electrical system
should malfunction or breakdown grounding provides a path of least
resistance for electric current, reducing the risk of electric shock. This
product is equipped with a cord having an equipment-grounding
plug� The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes
and ordinances�
⚠ WARNING
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the
product is properly grounded� Do not modify the plug provided
with the product if it will not fit the outlet; have a proper outlet
installed by a qualified electrician�
Assembly instructions
Description (fig. A)
Your treadmill is a piece of stationary fitness equipment used to
simulate walking or running without causing excessive pressure to the
joints�
Package contents (fig. B )
- The package contains the parts as shown in
fig� B�
- The package contains the fasteners as shown in fig. C. Refer to the
section “Description”
‼ NOTE
If a part is missing, contact your dealer.
Assembly (fig. C)
⚠ WARNING
Assemble the equipment in the given order.
Carry and move the equipment with at least two persons.
⚠ CAUTION
Place the equipment on a firm, level surface.
Place the equipment on a protective base to prevent damage to
the floor surface�
Allow at least 100 cm of clearance around the equipment.
Refer to the illustrations for the correct assembly of the
equipment�
Workouts
The workout must be suitably light, but of long duration. Aerobic
exercise is based on improving the body’s maximum oxygen uptake,
which in turn improves endurance and fitness. You should perspire,
but you should not get out of breath during the workout.
To reach and maintain a basic fitness level, exercise at least three
times a week, 30 minutes at a time. Increase the number of exercise
sessions to improve your fitness level. It is worthwhile to combine
regular exercise with a healthy diet. A person committed to dieting
should exercise daily, at first 30 minutes or less at a time, gradually
increasing the daily workout time to one hour. Start your workout at
low speed and low resistance to prevent the cardiovascular system
from being subjected to excessive strain�
As the fitness level improves, speed and resistance can be increased
gradually� The efficiency of your exercise can be measured by
monitoring your heart rate and your pulse rate�
Exercise Instructions
Using your fitness trainer will provide you with several benefits, it will
improve your physical fitness, tone muscle and in conjunction with a
calorie controlled diet help you lose weight.
The warming up phase
This stage helps get the blood flowing around the body and the
muscles working properly. It will also reduce the risk of cramp and
muscle injury. It is advisable to do a few stretching exercises as shown
below. Each stretch should be held for approximately 30 seconds, do
not force or jerk your muscles into a stretch - if it hurts, STOP
The exercise phase
This is the stage where you put the effort in. After regular use, the
muscles in your legs will become more flexible. Work to your but it is
very important to maintain a steady tempo throughout� The rate of
work should be sufficient to raise your heart beat into the target zone
shown on the graph below.
200
180
160
140
120
100
80
20 25 30 35 40 45 50 55 60 65 70 75
85 %
70 %
AGE
MAXIMUM
COOL DOWN
HEART RATE
TARGET ZONE
This stage should last for a minimum of 12 minutes though most
people start at about 15-20 minutes
The cool down phase
This stage is to let your Cardiovascular System and muscles wind
down. This is a repeat of the warm up exercise e.g. reduce your
tempo, continue for approximately 5 minutes. The stretching
exercises should now be repeated, again remembering not to force
or jerk your muscles into the stretch�
As you get fitter you may need to train longer and harder. It is
advisable to train at least three times a week, and if possible space
your workouts evenly throughout the week.
Muscle toning
To tone muscle while on your fitness trainer you will need to have the
resistance set quite high. This will put more strain on our leg muscles
and may mean you cannot train for as long as you would like. If you
are also trying to improve your fitness you need to alter your training
program. You should train as normal during the warm up and cool
down phases, but towards the end of the exercise phase you should
increase resistance making your legs work harder. You will have to
reduce your speed to keep your heart rate in the target zone�
16
English
Weight loss
The important factor here is the amount of effort you put in�
The harder and longer you work the more calories you will burn.
Effectively this is the same as if you were training to improve your
fitness, the difference is the goal.
Heart rate
Pulse rate measurement
(hand pulse sensors)
The pulse rate is measured by sensors in the handlebars when the
user is touching both sensors at the same time. Accurate pulse
measurement requires that the skin is slightly moist and constantly
touching the hand pulse sensors. If the skin is too dry or too moist,
the pulse rate measurement will become less accurate.
‼ NOTE
If you set a heart rate limit for your workout, an alarm will sound
when it is exceeded.
Maximum heart rate
(during training)
The maximum heart rate is the highest heart rate a person can safely
achieve through exercise stress. The following formula is used to
calculate the average maximum heart rate: 220 - AGE. The maximum
heart rate varies from person to person�
⚠ WARNING
Make sure that you do not exceed your maximum heart rate
during your workout. If you belong to a risk group, consult a
physician�
Beginner
50-60% of maximum heart rate
Suitable for beginners, weight-watchers, convalescents and persons
who have not exercised for a long time. Exercise at least three times a
week, 30 minutes at a time.
Advanced
60-70% of maximum heart rate
Suitable for persons who want to improve and maintain fitness.
Exercise at least three times a week, 30 minutes at a time.
Expert
70-80% of maximum heart rate
Suitable for the fittest of persons who are used to long-endurance
workouts.
Use
Master power switch (fig. D-A)
The equipment is equipped with a master power switch to shut down
the equipment completely
To start the equipment:
- Insert the mains plug into the wall socket.
- Set the master power switch to the on position.
To stop the equipment:
- Set the mains power switch to the off position.
- Remove the mains plug from the wall socket.
Safety key (Fig F-4)
The equipment is equipped with a safety key that must be properly
inserted into the console to start the equipment� If you remove the
safety key from the console, the equipment will stop immediately.
- Insert the safety key into the slot in the console�
- Make sure that the clip of the safety key is properly attached to
your clothing�
Make sure that the clip is not removed from your clothing before
the safety key is removed from the console�
Circuit breaker (Fig. E-2)
The equipment is equipped with a circuit breaker that interrupts the
circuit when the electricity load is above the maximum capacity. When
this occurs, the circuit breaker must be pressed.
⚠ WARNING
Before pressing the circuit breaker, remove the mains plug from
the equipment�
If the equipment shuts down, proceed as follows to restart the
equipment:
- Remove the mains plug from the equipment�
- Press the circuit breaker to restart the equipment�
- Insert the mains plug into the equipment�
‼ NOTE
Some circuit breakers used in homes are not rated for high
inrush currents that can occur when a treadmill is first turned
on or even during normal use� If your treadmill is tripping the
circuit breaker (even though it is the proper current rating and
the treadmill is the only appliance on the circuit) but the circuit
breaker on the treadmill itself does not trip, you will need
to replace the breaker with a high inrush type. This is not a
warranty defect. This is a condition we as a manufacture have no
ability to control�
Unfolding and folding the
equipment (fig. F1-F2)
The equipment can be unfolded for use (fig. F1) and folded for
transport and storage (fig. F2).
Refer to the illustrations for the correct way of unfolding and folding
the equipment�
Adjust incline setting (Manual)
- Fold up your treadmill. (Up)
- Take out adjuster pad safety pin�
- Adjust the adjuster pad in desired position.
- Secure the adjuster pad position with the safety pin.
- Unfold your treadmill. (Down)
‼ NOTE
Make sure both adjuster-pads are in same position to avoid your
treadmill to become unstable�
Adjusting the support feet (fig. F-7-8)
The equipment is equipped with 2 support feet. If the equipment is
not stable, the support feet can be adjusted.
- Turn the support feet as required to put the equipment in a stable
position�
- Tighten the locknuts to lock the support feet�
‼ NOTE
The machine is the most stable when all support feet are turned
fully in� Therefore start to level the machine by turning all
support feet fully in, before turning out the required support
feet to stable the machine�
17
English
Console (fig. E-1)
⚠ CAUTION
Keep the console away from direct sunlight.
Dry the surface of the console when it is covered with drops of
sweat.
Do not lean on the console�
‼ NOTE
The console switches to standby mode when the equipment is
not used for 10 minutes�
Buttons
Stop
- Stop workout.
Speed +
- Increases the speed (01.0 ~ 16 KM/H).
- Pressing once increases the speed 0,1 kph.
- Pressing and holding for two seconds will increase the speed faster.
- Scroll programs and change values in programming mode�
Speed -
- Decreases the speed (01.0 ~ 16 KM/H).
- Pressing once decreases the speed 0,1 kph.
- Pressing and holding for two seconds will decrease the speed
faster
- Scroll programs and change values in programming mode�
Mode
- Select program mode
- Confirm setting to enter next step in programming mode.
Program
- Select program mode. ( P1~P36, U1~U3, FAT)
Start/ Pause
- Start selected workout, or restart pause workout when being in
pause mode�
- Pause active workout.
Speed hot keys:
Speed Hot Keys are set as: 3, 4, 5, 6, 7, 8, 9, 10.
For example, the speed changes from any speed to 8 KPH by
pressing the
Speed Hot Key 8�
Explanation of display items
Speed
- Shows the actual treadmill speed in workout mode.
Distance
- Shows the ran distance workout mode.
- Shows the target distance when being in programming mode.
- Shows program selection when being in program mode.
Time
- Shows the ran time in workout mode.
- Shows the target time when being in programming mode.
Pulse
- Shows the pulse rate in workout mode, or “P” when no pulse is
measured�
Calories
- Shows the consumed calories in workout mode.
‼ NOTE
This data is a rough guide for comparison of different exercise
sessions which cannot be used in medical treatment
Programs
Quick start
- Press “START” button to start your workout without any pre-set
settings�
- Treadmill will start at minimum speed
of 1�0 KM/H”�
- Adjust SPEED manually at any time to change your workout, and
stop/ pause at anytime�
Countdown mode
- Press “MODE” button to open “Countdown” mode.
- Press “MODE” buttons to select countdown for : Time, Distance,
Calories.
- Press “SPEED +/-” buttons to set your desired Countdown goal.
- Press “START” button to start your workout.
‼ NOTE
Treadmill will stop when countdown goal is reached.
End your workout
- Press “STOP” button to stop workout and reset console.
- Press and hold “STOP” button to stop workout and reset console.
Preset Programs (P1~P36)
The equipment has 36 pre-set programs with different profiles. (Fig G)
- Press “MODE” button to open programming mode�
- Press “PROG” buttons to select “P1~P36” program, press
“MODE” button to confirm�
- Press “SPEED +/-” buttons to set your desired training time
Default training time is set on 30:00 minutes.
Range 10:00~99:00 min.
‼ NOTE
When set 00:00 minutes, the training will not stop, unless
stopped manually
- Press “START” button to start your workout.
Body Fat
The Body Fat program is program to indicate your fiscal state, based
on your body parameters and heart rate�
- Press “MODE” button to open programming mode�
- Press “PROG” buttons to select ”FAT”
program, press “MODE” button to confirm.
- The “Calories” display shows “F1” (SEX) .
The “Pulse” display shows “F1”
Press “SPEED +/-” buttons to select:
1: Male/ 2: Female press “MODE” button to confirm.
- The “Calories” display shows “F2” (Age) .
The “Pulse” display shows “25”
Press “SPEED +/-” buttons to select:10~99
press “MODE” button to confirm�
18
English
- The “Calories” display shows “F3” (Heigth) .
The “Pulse”display shows “170”cm
Press “SPEED +/-” buttons to select:100~220 cm
press “MODE” button to confirm�
- The “Calories” display shows “F4” (Weigth) .
The “Pulse” display shows “70”kg
Press “SPEED +/-” buttons to select: 20~150 kg
press “MODE” button to confirm�
- The “Calories” display shows “F5” (Active)
The “Pulse” display shows “- - - -” (Measure)
⚠ CAUTION
Holding the contact hand-grip heart rate measurement pads is
required for this function�
Result calculation:
- BODY TYPE: ( Body Fat ratio; 9 types)
FAT 0 ~19 Underweight
FAT 20 ~ 25 Standard
FAT 26 ~ 29 Overweight
FAT 30 ~ + Obesity
- BF = Body Fat ( in ratio % )
- Error code “ER” will show if no heart rate was detected during the
BF measurement process�
- Press “MODE” button to leave Body Fat program�
User programs (U-01~U-03)
The equipment has 3 user programs�
Each user program can be adjusted to personal requirements�
Each user program has a maximum of 12 steps�
The speed and the incline can be set for each step�
Each steps takes 1/12 of the total amount of time�
- Press “MODE” button to open programming mode�
- Press “PROG” buttons to select ”U-01~U-03” program, press
“MODE” button to confirm�
- Press “SPEED +/-” buttons to set your desired training time
Default training time is set on 30:00 minutes.
Range 10:00~99:00 min.
The “Distance” display shows “01”.
- Press the “SPEED +/-” buttons to set the speed� Press the
“MODE” button to confirm�
The main display shows “SE02”
- Repeat the above action to configure the other steps�
- Press the “START” button to start the program.
Warranty
Warranty terms
The consumer is entitled to the applicable legal rights stated in the
national legislation concerning the commerce of consumer goods�
This warranty does not restrict these rights. The Purchaser’s Warranty
is only valid if the item is used in an environment approved by Tunturi
New Fitness BV for that particular equipment. The product-specific
approved environment is stated in the Owner’s Manual provided with
your equipment�
Warranty conditions
The warranty conditions commence from the date of purchase.
Warranty conditions may vary per country, so please consult your
local dealer for the warranty conditions.
Warranty coverage
Under no circumstances shall Tunturi New Fitness BV or the Tunturi
Distributor be liable by virtue of this warranty or otherwise for any
special, indirect, secondary or consequential damages of any nature
arising out of any use or inability to use this equipment�
Warranty limitations
This warranty covers manufacturing defects in the fitness equipment
as originally packed by Tunturi New Fitness BV. The warranty shall
apply only under conditions of normal, recommended use of the
product as described in the Owner’s Manual and providing that
Tunturi New Fitness BV’s instructions for installation, maintenance and
use have been complied with. Neither Tunturi New Fitness BV’s nor
the Tunturi Distributors’
obligations apply to defects due to reasons beyond their control� The
warranty applies only to the original purchaser and is valid only in
countries where Tunturi New Fitness BV has an authorised importer.
The warranty does not extend to fitness equipment or components
that have been modified without the consent of Tunturi New Fitness
BV. Defects resulting from normal wear, misuse, abuse, corrosion, or
damage incurred during loading or transportation are not covered�
The warranty does not cover sounds or noises emitted during use
where these do not substantially impede the use of the equipment
and where they are not caused by a fault in the equipment.
The warranty does not cover defects arising from the failure to
carry periodic maintenance as outlined within the Owner’s Manual
for the product. Furthermore, the warranty does not cover defects
arising from usage and storage within an unsuitable environment
as described within the Owner’s Manual which should be indoors,
dry, dust and grit free and within a temperature range of +15°C to
+35°C. The warranty does not cover maintenance activities, such as
cleaning, lubricating, and normal part adjustments, nor installation
Procedures that customers can accomplish themselves, such as
changing uncomplicated meters, pedals and other similar parts not
requiring any dismantling/reassembling of the fitness equipment�
Warranty repairs carried out by other than authorised Tunturi
representatives are not covered�
Failure to follow the instructions given in the Owner’s Manual will
invalidate the product’s warranty.
Cleaning and maintenance
⚠ WARNING
Before cleaning and maintenance, remove the mains plug from
the wall socket.
Do not use solvents to clean the equipment�
- Do not block the ventilation openings� Keep the ventilation
openings clear from dust, dirt and other obstructions.
- Clean the equipment with a soft, absorbent cloth after each use.
- Clean the visible parts of the equipment with a vacuum cleaner
with a small suction nozzle
- Regularly check that all screws and nuts are tight.
19
English
Belt and Running Deck
Your treadmill uses a very high-efficient low-friction bed. Performance
is maximized when the running deck is kept as clean as possible.
Use a soft, damp cloth or paper towel to wipe the edge of the belt
and the area between the belt edge and frame. Also reach as far
as practical directly under the belt edge� This should be done once
a month to extend belt and running deck life. Use water only - no
cleaners or abrasives. A mild soap and water solution along with a
nylon scrub brush will clean the top of the textured belt. Allow the
belt to dry before using�
Lubrication (fig. F-4)
The running belt must be checked for lubrication once per 2 months,
based on the average use of 60 minutes per day
⚠ WARNING
Before lubrication, remove the mains plug from the wall socket.
⚠ CAUTION
Only lubricate the running belt if necessary� If you apply too
much lubricant, the running belt will slip easily due to lack of
friction�
- Stand steadily on the running belt�
- Take hold of the front handlebar and push the running belt with
your feet so that it slides back and forth� The running belt must
move smoothly and evenly without making sound.
- If the running belt does not move smoothly and evenly or if the
running belt does not move at all, touch the underside of the
running belt with your fingertips to check the lubrication:
If you feel lubrication or your fingertips are shiny, there is
sufficient lubrication on the running belt�
If you do not feel lubrication or your fingertips are dusty or
rough, apply lubricant (15-20 ml) in the middle of the running
deck under the running belt and let the equipment operate at
5km/h for at least 5 minutes�
After lubrication, do not fold the equipment before having done
a workout for 20 minutes with a speed of at least 5 km/h. The
lubricant will be spread evenly over the running belt.
Belt Dust
This occurs during normal break-in or until the belt stabilizes� Wiping
excess off with a damp cloth will minimize build-up.
General Cleaning
Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent buildup. Twice a year, you should remove the black motor
hood and vacuum out dirt that may accumulate�
UNPLUG POWER CORD BEFORE THIS TASK.
Belt adjustments
Adjustment must be made from the rear roller. The adjustment bolts
are located at the end of the step rails in the end caps�
- Tighten the rear roller bolts (clockwise) only enough to prevent
slippage at the front roller� Turn both running belt tension
adjustment bolts in increments of 1/4 turn each and inspect for
proper tension by walking on the belt at a low speed, making sure
the belt does not slip� Keep tensioning the bolts until the belt
stops slipping�
- If you feel the belt is tight enough, but it still slips, the problem
may be a loose Motor drive belt under the front cover
- Do Not Over-tighten
Over tightening will cause belt damage and premature bearing
failure�
Running belt tracking adjustment
The performance of your treadmill is dependent on the frame running
on a reasonably level surface. If the frame is not level, the front and
back roller cannot run parallel, and constant belt adjustment may be
necessary
The treadmill is designed to keep the running belt reasonably
centered while in use. It is normal for some belts to drift near one
side while the belt is running with no one on it. After a few minutes
of use, the running belt should have a tendency to center itself. If,
during use, the belt continues to move toward one side, adjustments
are necessary
Exception:
During rehabilitation where the user is using one leg much stronger
than the other, it might happen that the running belt drifts to one
side� In these cases you should not adjust unless the running belt
does not centre itself during normal condition usage�
To set running belt tracking (fig. F-5)
A 10 mm Allen wrench is provided to adjust the rear roller. Make
tracking adjustments from the left side only� Set belt speed at
approximately 3 to 5 kph�
Remember, a small adjustment can make a dramatic difference!
Turn the bolt clockwise to move the belt to the right.
Counterclockwise to move to the left. Turn the bolt only a 1/4 turn
and wait a few minutes for the belt to adjust itself. Continue to make
1/4 rotation turns until the belt stabilizes in the center of the running
deck�
The belt may require periodic tracking adjustment depending on use
and walking/running characteristics. Some users will affect tracking
differently� Expect to make adjustments as required to center the
tread-belt. Adjustments will become less of a maintenance concern
as the belt is used. Proper belt tracking is an owner responsibility
common with all treadmills.
‼ NOTE
Damage to the running belt because of incorrect running-belt
adjustments is not covered by the products warranty.
Troubleshooting
Despite continuous quality control, defects and malfunctions caused
by individual components may occur in the equipment� In most cases
it’s unnecessary to take the whole device in for repair, as it’s usually
sufficient to replace the defective part�
If the equipment does not function properly during use, contact your
Tunturi dealer immediately. Always give the model and serial number
of your equipment. Please state also the nature of the problem,
conditions of use and purchase date�
If you require spare parts, always give the model, serial number of
your equipment and the spare part number for the part you need�
The spare part list is at the back of this manual� Use only spare parts
mentioned in the spare part list�
Error codes
If the display shows an error code
(marked with “E”/ “DC” + number), restart the equipment and check
whether the display still shows the error code. If the display still shows
the error code, immediately contact the dealer.
20
English
Shaky or unstable feeling during use
If the machine feels unstable or unstable during operation, it is
advisable to adjust the support feet to bring the frame to the correct
height. Read the instructions in this manual in section: “Use”
Transport and storage
⚠ WARNING
Before cleaning and maintenance, remove the mains plug from
the wall socket.
Carry and move the equipment with at least two persons.
Make sure that there are no other persons or objects under the
equipment�
When folding the folding the equipment, make sure that you
hear the equipment lock into position to prevent the equipment
from dropping back down.
- Move the equipment as shown (fig. F3). Move the equipment
and carefully put the equipment down. Place the equipment on
a protective base to prevent damage to the floor surface� Move
the equipment carefully over uneven surfaces� Do not move the
equipment upstairs using the wheels, but carry the equipment by
the handlebars�
- Store the equipment in the upright position (fig. F1). Store the
equipment in a dry place with as little temperature variation as
possible�
Additional information
Packaging disposal
Government guidelines ask that we reduce the amount of waste
material disposed of in land fill sites� We therefore ask that you
dispose of all packaging waste responsibly at public recycling centres.
End of life disposal
We at Tunturi hope you enjoy many years of enjoyable use from your
fitness trainer. However, a time will come when your fitness trainer will
come to the end of its useful life� Under ‘European WEEE Legislation
you are responsible for the appropriate disposal of your fitness trainer
to a recognised public collection facility
Technical data
Parameter Unit of measurement Value
Mains voltage VAC 210 ~ 240
Mains frequency HZ 50 ~ 60
Speed Km/H 1�0 ~ 16�0
Incline Step 3
Length
(folded)
Cm 152�0
( 94.0)
Width Cm 70�0
Height
(folded)
Cm 135�0
(135.0)
Weight Kg 47�0
HR� receiver Handgrip Contact
5�3~ 5�4 Khz�
Bluetooth BLE
ANT+
Declaration of the manufacturer
Tunturi New Fitness BV declares that the product is in conformity with
the following standards and directives: EN 957 (HC), EN ISO 209957-
1: 2013, EN 957-6-2010+A1: 2014, 2014/ 30/ EU. The product
therefore carries the CE label.
04-2020
Tunturi New Fitness BV
Purmerweg 1
1311 XE Almere
The Netherlands
Disclaimer
© 2020 Tunturi New Fitness BV
All rights reserved.
- The product and the manual are subject to change�
- Specifications can be changed without further notice.
- Check our website for the latest user manual version.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Tunturi T35 Le manuel du propriétaire

Taper
Le manuel du propriétaire