Vari-Lite VL800 PROPAR Guide de démarrage rapide
- Catégorie
- Stroboscopes
- Taper
- Guide de démarrage rapide
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Introduction
About This Guide
This Quickstart Guide is intended for a knowledgeable user to unpack, install, and use the VL800
PROPAR in a short time period. For the complete manual in PDF format, please visit our web site at:
www.Vari-Lite.com and click the user manual download link on the product downloads page. The
complete manual provides you all information related to accessories, menu structures, DMX channel
mapping/modes, and care for your new luminaire.
WARNING
:
It is important to read ALL accompanying safety and installation instructions to avoid damage to the
product and potential injury to yourself or others. AVERTISSEMENT: Il est important de lire toutes
les instructions de sécurité et d'installation d'accompagnement pour éviter d'endommager le produit
et les risques de blessures à vous-même ou les autres.
Notes:
•
For complete product description, feature and specifications, refer to product
datasheet on the Vari-Lite web site at
www.Vari-Lite.com
•
For power requirements, refer to
“Current vs. Voltage” on page 10
.
Additional Documentation
For more information on installing DMX512 control systems, the following publication is available for
purchase from the United States Institute for Theatre Technology (USITT), “Recommended Practice for
DMX512: A Guide for Users and Installers, 2nd edition” (ISBN: 9780955703522). USITT Contact
Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, New York 13210-1844 USA
Phone: 800-938-7488 or +1-315-463-6463
Fax: 866-398-7488 or+1-315-463-6525
Web Site: www.usitt.org
Customer Service
Our Goal
At Vari-Lite, we are committed to providing you the highest quality in customer service. Our
comprehensive resources are available to help your business succeed and ensure you get the full
benefit of being a Vari-Lite customer. Whether your needs are telephone troubleshooting assistance,
product training or technical service, our full-time staff of experienced professionals are on-hand to
provide support.
2 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
How to Reach Us
For assistance in your area, call the dealer from which your product was purchased.
or Contact an Authorized Service Center
or Contact the Vari-Lite Customer Service Department,7am-6pm CST Monday through Friday,
at the following:
phone: 1-877-VARI-LITE (1-877-827-4548) or +1-214-647-7880
e-mail: entertainment.sercice@signify.com
Note:
Performing maintenance procedures may void the product warranty. Refer to the Vari-
Lite Limited Warranty card included in the product shipping package for more information. For
all service and maintenance issues, please contact your local Authorized VARI
❋
LITE Dealer
or Service Center.
Additional Resources
For additional resources and documentation on this product, please visit our website at
www.Vari-Lite.com and follow the Support link.
Version as of: July 2
nd
, 2020
VL800 PROPAR QuickStart Guide
©2019 Signify Holdings. All rights reserved.
2 July 2020 3
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Compliance & Safety Notices
Compliance
SAFETY Standards
We, Signify, 10911 Petal Street, Dallas, Texas 75238 declare under our responsibility for the
products contained herein are in conformity with the essential requirements of the following
European Directives and Safety standards for United States and Canada.
EN 60598-2-17
EMC Standards
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when this equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with Vari-Lite system, service, and safety guidelines, may cause
harmful interference to radio communications.
CFR47 FCC Part 15 Class B
EN 61547
EN 55015
EN61000-3-2
EN61000-3-3
ICES-003
EN62778
AS/NZS CISPR 15
UL 1573
CSA C22.2#166
Safety Notice
It is extremely important to read ALL safety information and instructions provided in this
manual and any accompanying documentation before installing and operating the products
described herein. Heed all cautions and warnings during installation and use of this product.
Safety symbols used throughout this manual are as follows:
CAUTION advising of potential damage to product.
WARNING advising of potential injury or death to persons.
4 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
GENERAL INFORMATION PERTAINING TO PROTECTION AGAINST ELECTRICAL SHOCK,
FIRE, EXPOSURE TO EXCESSIVE UV RADIATION, AND INJURY TO PERSONS CAN BE
FOUND BELOW.
WARNING:
INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST FIRE
1.
Luminaires may be mounted on any type of surface as long as mounting instructions are
f
ollowed. See instructions detailed in this manual.
2.
Note distance requirement from combustible materials or illuminated objects for
VARI
❋
LITE luminaires.
WARNING:
INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST ELECTRICAL SHOCK
1. VARI
❋
LITE luminaires are designed for dry locations only. Exposure to rain or moisture
may
damage luminaire.
2. Disconnect power before servicing any VARI
❋
LITE equipment.
3. Servicing to be performed by qualified personnel only.
WARNING:
INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST EXCESSIVE EXPOSURE TO
UV RADIATION
1. Many VARI
❋
LITE luminaires use a LED that produces UV radiation. DO NOT look
directly at LED.
2. It is hazardous to operate luminaires without lens or shield. Shields, lenses, or ultraviolet
screens shall be changed if they have become visibly damaged to such an extent that
their effectiveness is impaired. For example, by cracks or deep scratches. Replace any
cracked or protective shields.
W
ARNING:
INSTRUCTIONS FOR PROTECTION AGAINST INJURY TO PERSONS
1. Exterior surfaces of the luminaire will be hot during operation. Use appropriate safety
equipment (gloves, eye protection, etc.) when handling and adjusting hot equipment and
components.
W
ARNING:
RFINTERFERENCE
This is a Class A product. In a domestic environment this product may cause radio
interference, in which case, the user may be required to take adequate measures.
WARNING:
Caution! Do not stare into the beam, RG2
2 July 2020 5
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
WARNING:
The light source contained in this luminaire shall only be replaced by the manufacturer or his
service agent or a similar qualified person.
Notes de sécurité
Avant de procéder à l’installation des produits décrits dans ce guide et de les mettre en
marche, il est extrêmement important de lire TOUS les renseignements et TOUTES les
directives de sécurité contenues dans ce guide ainsi que toute documentation jointe. Tenir
compte de tous les avertissements et suivre toutes les précautions pendant l’installation et
l’utilisation de cet appareil.
A
TTENTION Ce symbole annonce que l’appareil risque d’être
endommagé
.
AVERTISSEMENT Ce symbole annonce qu’il y a risque d’accident
grave ou même fatal.
CETTE SECTION CONTIENT DES INFORMATIONS GÉNÉRALES POUR SE PROTÉGER CONTRE LES
DÉCHARGES ÉLECTRIQUES, LES INCENDIES, L’EXPOSITION EXCESSIVE AUX RAYONS UV ET TOUT
AUTRE ACCIDENT POUVANT ENTRAÎNER DES BLESSURES.
AVERTISSEMEN
，
DIRECTIVES POUR SE PROTEGER CONTRE LES INCENDIES
1. Les luminaires peuvent être fixés sur tout type de surface tant que les directives de
montage sont respectées. Voir les explications détaillées dans ce guide.
2. Vérifier la distance à respecter entre les matériaux combustibles ou les objets
illuminés et les luminaires VARI
❋
LITE.
AVERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE LES DÉCHARGES ÉLECTRIQUES
1. Les luminaires VARI
❋
LITE sont conçus pour une utilisation au sec uniquement.
Une exposition à la pluie et à l’humid-ité risque d’endommager le luminaire.
2.
Débrancher l’appareil avant de procéder à la révision de tout matériel VARI
❋
LITE.
3.
Les révisions doivent être effectuées uniquement par des personnes qualifiées.
AVERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE UNE EXPOSITION EXCESSIVE AUX RAY-
ONS UV
1. Plusieurs luminaires VARI
❋
LITE utilisent une LED qui produit des rayons UV. NE
PAS fixer son regard sur la LED.
2. L’utilisation des luminaires sans lentille ou blindage pose des risques. Tous
blindages, lentilles ou écrans ultraviolet visiblement endommagés au point que leur
efficacité en est affectée doivent être remplacés, par exemple s’il y a des fissures o
u
de
profondes rayures..
A
VERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE LES ACCIDENTS POUVANT ENTRAÎNER
DES BLESSURES
1.
Les surfaces externes du luminaire deviennent brûlantes quand l’appareil est en
marche. Pour manœuvrer ou ajuster des appareils brûlants et leurs composants, se
protéger suffisamment (gants, protection pour les yeux, etc.).
6 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
AVERTISSEMENT:
INTERFÉRENCE RF
Cet appareil est de Classe A. Dans un environnement domestique, cet appareil peut
causer des interférences radio, et si c’est le cas, l’utilisateur peut avoir à prendre des
mesures adéquates.
AVERTISSEMENT:
Mise en garde! Ne regardez pas dans le faisceau, RG2
AVERTISSEMENT:
Le module de led contenue dans ce luminaire ne doit être remplacée que par le fabricant,
son agent de service ou une personne qualifiée.
2 July 2020 7
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Other
Operational Temperature / Température de fonctionnement
•
The VL800 PROPAR has one operational mode. Refer to Table 1-1, “VL800 PROPAR
Environmental Operational Temperatures” for information on environment temperatur
e
r
anges associated with this mode.
•
The VL800 PROPAR Luminaire a un mode opérationnel. Reportez-vous à Table 1-1,
“
VL800 PROPAR Environmental Operational Temperatures” pour des informations sur
les plages de température environnementales associées à ce mode.
Table 1-1: VL800 PROPAR Environmental Operational Temperatures
Minimum to Maximum Environmental
Temperature
c
F
0
°
to
40°
32° to 104°
Part Numbers
VL800 PROPAR Numbers
VL800 PROPAR
912400575007
8 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
About the VL800 PROPAR
Included Items
The following illustration shows all items included with the luminaire:
Note: Please check with Vari-Lite or Authorized VARI❋LITE Dealer for availability on accessories
Seetronic power connector
Clamp contained in the carton box
VL800 PROPAR
QuickStart Guide
2 July 2020 9
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Connecting Power and Data
Connecting Power
The luminaire requires standard AC power distribution from 100-240 VAC, 50/60 Hz. Current
required depends on the AC supply voltage and product model. Refer to “Current vs. Voltage”
on page 10 for all models covered in this manual.
Note: The mating Seetronic power connector is supplied; however, you will need to purchase
or construct a cable appropriate for your application.
Figure 1: Power Connector
Depending on the application, the luminaire’s AC input cable may require a different
connector. If required, install a new connector meeting your requirements using the
following wire color code reference:
Wire*
Connection
Green/Yellow
AC Ground
Blue
AC Neutral
Brown
AC
Li
ne
* International (Harmonized)8tandard
WARNING: DO NOT connect to three-phase service in countries with 240 volt power.
AVERTISSEMENT: NE PAS se connecter au service en trois phases dans les pays avec
puissance de 240 volts.
For single-phase power at 240 volts RMS:
Connection
Pin
AC Neutral
X
AC Line
Y
Ground (Earth)
G
For three-phase power at 200 volts RMS:
Connection
Pin
Phase 1
X
Phase 2
Y
Ground (Earth)
G
10 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
WARNING: It is not recommended to power any VARI
❋
LITE luminaire from a dimmer -
even in 'NONDIM' mode. Dimmer and non-dim modules are not suitable sources of power
because their output modifies the AC wave form. This may work for a short time, but will
eventually result in power problems, luminaire mis-operation and/or failure and may void
the luminaire’s warranty.
AVERTISSEMENT:
Il n'est pas recommandé pour alimenter un luminaire VARI
❋
LITE
d'un gradateur - même en mode 'NONDIM’. Modules de gradation et non sombres ne sont
pas des sources appropriées de pouvoir parce que leur production modifie la forme
d'onde AC. Cela peut fonctionner pendant une courte période, mais finira par entraîner
des problèmes d'alimentation, luminaires mauvais fonctionnement et / ou l'échec et peut
annuler la garantie de l'appareil.
Current vs. Voltage
Table 1-2, VL800 PROPAR Luminaire - Current vs. Voltage (260W LED) provides the
luminaire’s current draw at specific voltages. Total Luminaire Current is calculated with the LED
on and all motors sequencing.
WARNING: It is the responsibility of the user to adequately protect supply source with a correct
size and type circuit breaker and not overload circuits. AVERTISSEMENT: Il est de la
responsibilité de l'utilisateur de protéger adéquatement la source d'alimentation avec une taille
correcte et le disjoncteur de type et surchargez pas les circuits.
Table 1-2: VL800 PROPAR Luminaire - Current vs. Voltage (260W LED)
AC Voltage at 60HZ
Total Luminaire Current
(Motor + LED Current)
100V
2.65A
110V
2.32A
120V
2.20A
130V
1.96A
200V
1.32A
210V
1.27A
220V
1.23A
230V
1.22A
240V
1.18A
Connecting Data
A maximum of 32 luminaires may be connected in any one DMX data link.
A maximum of 3 luminaries may be connected in 120V, 60Hz.
A maximum of 5 luminaries may be connected in 230V, 50Hz
Note: This maximum limit applies to the luminaire "daisy chain" only. Your system or
console may require fewer luminaires on a single data link path. Consult your console
documentation for more information.
2 July 2020 11
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
To connect power and data:
Step 1. Connect data cable from console to first luminaire in chain at DATA IN connector.
Step 2. If required, connect additional data cables from DATA THRU connectors to DATA IN
Step 3. At last luminaire in link, install male termination connector at DATA THRU connector.
(Luminaires and other devices on the same DMX chain may not function properly
without termination)
VL800 PROPAR
Luminaire Channel Requirements*
DMX512 Channels
Description
Menu Display
15 Channels
16 Bit Mode (Default)
15
*
*DMX terminator required for last fixture on DMX line.
Figure 2: Data Link
Step 4. Connect AC Input Cable connector to power input source.
Step 5. Dress AC input and data cables and secure them so that they will not interfere with
luminaire head and yoke movement.
12 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Installation Procedures
Floor Mounting the Luminaire
This luminaire included in this manual are designed to sit directly in a floor installation application.
When used in this type of application, be sure to leave enough space around the luminaire to allow
proper, uninterrupted airflow for cooling and movement.
Hanging the Luminaire
The VL800 PROPAR Luminaire can be hung horizontally or vertically from any structure designed
to work with the type of load created Clamp and Quick lock fastener or other mounting hardware
are required. Many compatible truss hooks are available from different manufacturers for your
particular needs.
One Quick-lock fastener per luminaire is required. If mounting method does not use truss hooks,
two attachment points per luminaire, are required. Always ensure the diameter of safety cable is at
least 4 mm, which can support at least 12 times of weight of unit.
Install mounting hardware and brackets:
Step 1. Bolt each clamp to the Omega holder with
screw and lock nut through the hole in the
holder as shown in Figure 3
Note: Various types of truss hooks can be used.
The Clamp (as shown in the example above) as
well as many other standard hooks, can be
ordered separately.
S
tep 2.
Faster the omega holders on the bottom of
the base by inserting quick-lock fasteners
into the holes of the base and tighten fully
clockwise. Figure 3: Quick-lock Fastener Installation
Step 3.
Hang the fixture to the support through clamp and faster the screws, faster the safety
cable through the bottom of the base and over the support.
2 July 2020 13
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
WARNING: Ensure that the bracket locking mechanism is fully seated after the bracket is
installed on the luminaire.
Figure 4: Installing Brackets on Luminaire Enclosure
Installing in Truss
:
Step l. Lift luminaire into mounting position.
Step 2. Secure in place with clamp handle. Ensure clamp handle hardware that Quick-lock fastener
hook in place (eg. wing bolt) is properly tightened and that luminaire is fully supported..
Step 3. Attach safety cable (as required) as follows (refer to Figure 5):
a. Loop safety cable at least once around safety cable anchor point rod.
14 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
b. Loop safety cable at least once around truss/pipe and secure around pipe.
Note, truss hooks shown are sold separately. Truss and pipe by others.
Figure 5: Safety Cable Installation / Luminaire Hanging
Step 4.
Make sure hanger is disengaged so luminaire moves freely
.
Step 5.
Connect power and data cables according to procedure given in “Connecting Data” on page
9
.
When hanging the luminaire in a side hang position, natural convection and the designed direction
of the inlet and exhaust cooling fans dictate that the inlet should be closest to the floor and the
exhaust should be towards the ceiling. This eliminates the possibility of one luminaire blowing
exhaust air into the inlet of the luminaire next to it when the luminaires are side-by-side.
If the luminaires are stacked on top of one another in a side hang, a 45° enclosure orientation with
the fan inlet closest to the floor.
2 July 2020 15
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Menu Operation
LCD Display and Menu System
The VL800 PROPAR Luminaire’s LCD Display and Menu System provide local control for
accessing the following fixture’s settings:
•
Address – to set the DMX address
•
Configure – various parameter settings, set LED, display, reset defaults
•
DMX – change the map, set address,
•
Fixture – fixture status, reboot, software version, view fixtures hours, crossload, service
•
Manual Control – to set the intensity, all functions
•
Test – to test functions of parameters
The menu system is controlled at the Menu Display available at the enclosure input panel. If there
are multiple luminaires in a system, any settings or changes would need to be made at each LCD
Menu as desired.
16 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Menu Controls
The menu system is controlled by an [MENU], [Enter] and two Arrow (
) buttons.
Thes
e buttons function are shown in Figure 7
.
Figure 7: Menu Control
LCD Display and Menu System Operation
The LCD Display Menu system consists of several categories. Use the Menu Buttons to
access and make changes to the menu items. When the desired menu item is reached
，
press the desired Menu Button to display the menu options and to navigate and configure the
menu options as required.
To navigate and access menu setting/selections:
Step 1. Make sure unit is powered and turned on.
Step 2. Press [MENU] to access menu categories.
Step 3. Use two Arrow ( ) buttons to navigate through the various options and
settings.
Step 4. Once menu item is reached, press [Enter] to access the menu item parameters.
Step 5. Make changes to parameters as desired.
Step 6. Press [Enter] button to accept changes.
DMX Address
To set, edit
，
and save a DMX address:
Step 1. Press [MENU].
Step 2. Press [Up] / [Down] ( ) arrows until Address (DMX Address) appears. Press [Enter].
Step 3. Use [Up] / [Down] ( ) arrow buttons to select the desired digit.
Step 4. Once all digits are set in DMX address, press [Enter] to set.
Step 5. DMX will display and is saved.
2 July 2020 17
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Status Bar
The Status Bar (as illustrated in Figure 8) is present at all times and displays luminaire
operational information of the luminaire. The Status Bar contains the following information:
Figure 8: LCD Display Status Bar
•
LED – indicates current LED state - ON or OFF.
•
MODE – indicates current mode, standard, studio and whisper mode.
•
ERRORS – Displays a number indicating the total amount of current errors can cycle
t
hrough short text descriptions of each error. Example: “Fan” or “LED”. When errors ar
e
pr
esent, messages will appear in red text. When no errors are present, NO will display.
•
MAP – indicates 16bits or 8bits.
•
ADDR – Displays the current DMX address for the fixture. NOTE, when the fixture does
not detect a DMX input signal, the DMX address text will display in red text.
Quick Reference Menu Key Shortcuts
Menu key shortcuts
Function
Holding Menu at Power up
bypass motor
Menu + Up ( )
ReCAL All
Menu + Down ( )
Pan / Tilt Deactivated
Menu + Enter
Factory Defaults
Enter + Up ( )
Lamp On
Enter + Down ( )
Lamp Off
Up ( ) + Down ( )
Display Invert
18 2 July 2020
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
Quick Reference DMX Maps
The summary list DMX maps for the VL800 PROPAR are indicated in Table 1-3.
Table 1-3: VL800 PROPAR 16-Bit Enhanced DMX Channel Summary Listing
DMX Channel Description DMX Channel Description
1 Intensity High 9 Blue low
2 Intensity Low 10 White High
3 Zoom 11 White low
4 Red High 12 Color Preset
5 Red Low 13
Strobe Speed
6 Green High 14 Strobe Control
7 Green low 15 Control Channel
8 Blue High
2 July 2020 19
VARI❋LITE - VL800 PROPAR QUICKSTART GUIDE
All rights reserved.
www Vari Lite com. -.
Signify Holdings
c
1.214.647.7880
1.877.VARILITE
Dallas.Texas 75238
Vari-Lite
10911Petal Street
20 2 July 2020
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Vari-Lite VL800 PROPAR Guide de démarrage rapide
- Catégorie
- Stroboscopes
- Taper
- Guide de démarrage rapide
dans d''autres langues
Documents connexes
-
Vari-Lite VL800 EVENTWASH Guide de démarrage rapide
-
-
Vari Lite VL 2600 Guide de démarrage rapide
-
-
-
-
-