Vari Lite VL 2600 Guide de démarrage rapide

Catégorie
Stroboscopes
Taper
Guide de démarrage rapide

Ce manuel convient également à


VL 2600 Profile/Spot/Wash
Luminaire QuickStart Guide
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
1 29 May 2018 02.1711.0022
Introduction
About This Guide
This Quickstart Guide is intended for a knowledgeable user to unpack, install, and use the VL2600
Profile/Spot/Wash Luminaire in a short time period. For the complete manual in PDF format, please
visit our web site at: www.Vari-Lite.com and click the user manual download link on the product
downloads page. The complete manual provides you all information related to accessories, menu
structures, DMX channel mapping/modes, and care for your new luminaire.
Read this manual in its entirety before operating luminaire. Keep this guide for future reference.
WARNING: It is important to read ALL accompanying safety and installation instructions to avoid
damage to the product and potential injury to yourself or others. AVERTISSEMENT: Il est important
de lire toutes les instructions de sécurité et d'installation d'accompagnement pour éviter d'endommager
le produit et les risques de blessures à vous-même ou les autres.
Notes:
For complete product description, features, and specifications, refer to product
datasheet on the Vari-Lite web site at www.Vari-Lite.com
For power requirements, refer to “Current vs. Voltage” on page 14.
VL 2600 Luminaires accept glass gobos only. Use of metal gobos will void the
luminaire’s warranty.
Additional Documentation
For more information on installing DMX512 control systems, the following publication is available for
purchase from the United States Institute for Theatre Technology (USITT), “Recommended Practice
for DMX512: A Guide for Users and Installers, 2nd edition” (ISBN: 9780955703522). USITT Contact
Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, New York 13210-1844 USA
Phone: 800-938-7488 or +1-315-463-6463
Fax: 866-398-7488 or +1-315-463-6525
Web Site: www.usitt.org
Cu s t o m e r S e r vic e
Our Goal
At Vari-Lite, we are committed to providing you the highest quality in customer service. Our
comprehensive resources are available to help your business succeed and ensure you get the full
benefit of being a Vari-Lite customer. Whether your needs are telephone troubleshooting assistance,
product training or technical service, our full-time staff of experienced professionals are on-hand to
provide support.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 2
How to Reach Us
For assistance in your area, call the dealer from which your product was purchased.
or Contact an Authorized Service Center
or Contact the Vari-Lite Customer Service Department, 7am - 6pm CST Monday through Friday, at
the following:
phone:1-877-VARI-LITE (1-877-827-4548) or +1-214-647-7880
e-mail: entertainment.service@signify.com
Note: Performing maintenance procedures may void the product warranty. Refer to the Vari-LIte
Limited Warranty card included in the product shipping package for more information. For all
service and maintenance issues, please contact your local Authorized VARILITE Dealer or Service
Center.
Additional Resources
For additional resources and documentation on this product, please visit our website at
www.Vari-Lite.com and follow the Support link.
Document Number: 02.1711.0022
Version as of: May 29 2018
VL 2600 Profile/Spot/Wash Luminaire QuickStart Guide
©2018 Signify Holdings. All rights reserved.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
3 29 May 2018 02.1711.0022
Co m p lia n c e & S a fe t y No t ic e s
Co m p lia n c e
SAFETY Sta nda rds
We, Signify, 10911 Petal Street, Dallas, Texas 75238 declare under our responsibility for the
products contained herein are in conformity with the essential requirements of the following
European Directives and Safety standards for United States and Canada.
EN 60598-1:2015
EMC Sta nda rds
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when this equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with Vari-Lite system, service, and safety guidelines, may cause harmful interference to radio
communications.
47CFR FCC Part 15 Class B 2016
EN 61547:2009
EN 55015:2013
ICES-003: 2016
UL 1573 Issue: 2003/05/29 Ed: 4 Rev: 2016/12/22
CSA C22.2#166:2015 Ed.2
Safety Notice
It is extremely important to read ALL safety information and instructions provided in this manual and
any accompanying documentation before installing and operating the products described herein. Heed
all cautions and warnings during installation and use of this product.
Safety symbols used throughout this manual are as follows:
CAUTION advising of potential damage to product.
WARNING advising of potential injury or death to persons.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 4
GENERAL INFORMATION PERTAINING TO PROTECTION AGAINST ELECTRICAL SHOCK,
FIRE, EXPOSURE TO EXCESSIVE UV RADIATION, AND INJURY TO PERSONS CAN BE
FOUND BELOW.
WARNING:
INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST FIRE
1. VARILITE luminaires have been designed for use with specific lamp types. The VL 2600 Profile/Spot/Wash
Luminaire requires a certain type of lamp (see
“Replacement Items/Accessories” on page 8 for all lamp types). Installing
another type or unapproved lamp may be hazardous.
2. Luminaires may be mounted on any type of surface as long as mounting instructions are followed. See instructions
detailed in this manual.
3. Note distance requirement from combustible materials or illuminated objects for VARILITE luminaires.
4. Four units is the maximum number of fixtures that may be interconnected at 220-240V(15A).
WARNING:
INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST ELECTRICAL SHOCK
1. VARILITE luminaires are designed for dry locations only. Exposure to rain or moisture may damage luminaire.
2. Disconnect power before servicing any VARILITE equipment.
3. Servicing to be performed by qualified personnel only.
4. If the external flexible cable or cord of the luminaire is damaged, it must be replaced by the manufacturer or authorized
service center.
WARNING:
INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST EXCESSIVE EXPOSURE TO
UV RADIATION
1. Many VARILITE luminaires use a lamp that produces UV radiation. DO NOT look directly at lamp.
2. It is hazardous to operate luminaires without lens or shield. Shields, lenses, or ultraviolet screens shall be changed if they
have become visibly damaged to such an extent that their effectiveness is impaired. For example, by cracks or deep
scratches. Replace any cracked or protective shields.
WARNING:
INSTRUCTIONS FOR PROTECTION AGAINST INJURY TO PERSONS
1. Exterior surfaces of the luminaire will be hot during operation. Use appropriate safety equipment (gloves, eye protection,
etc.) when handling and adjusting hot equipment and components.
2. Luminaires will have a hot lamp when operating. Disconnect power and allow lamp to cool before replacing.
3. Arc lamps emit ultraviolet radiation which can cause serious skin burn and eye inflammation. Additionally, arc lamps
operate under high pressure at very high temperatures. Should the lamp break, there can exist a danger of personal injury
and/or fire from broken lamp particles being discharged.
4. Wear eye protection when relamping.
5. Appropriate safety equipment (gloves, eye protection) should be used when handling damaged lamps.
6. If lamp is touched with bare hands, clean lamp with denatured alcohol and wipe with lint-free cloth before installing or
powering up the luminaire.
7. The lamp shall be changed if it has become damaged or thermally deformed.
WARNING:
RF INTERFERENCE
This is a Class A product. In a domestic environment this product may cause radio interference, in
which case, the user may be required to take adequate measures.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
5 29 May 2018 02.1711.0022
Notes de sécurité
Avant de procéder à l’installation des produits décrits dans ce guide et de les mettre en marche, il est
extrêmement important de lire TOUS les renseignements et TOUTES les directives de sécurité
contenues dans ce guide ainsi que toute documentation jointe. Tenir compte de tous les avertissements
et suivre toutes les précautions pendant l’installation et l’utilisation de cet appareil.
Les symboles de sécurité utilisés dans ce guide sont les suivants :
CETTE SECTION CONTIENT DES INFORMATIONS GÉNÉRALES POUR SE PROTÉGER
CONTRE LES DÉCHARGES ÉLECTRIQUES, LES INCENDIES, L’EXPOSITION EXCESSIVE
AUX RAYONS UV ET TOUT AUTRE ACCIDENT POUVANT ENTRAÎNER DES BLESSURES.
AVERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE LES INCENDIES
1. Les luminaires VARILITE ont été conçus pour être utilisés uniquement avec certaines type de lampes. Vérifier le type
de lampe avant de remplacer les lampes. L’installation d’un autre type de lampe peut poser un danger.
2. Les luminaires peuvent être fixés sur tout type de surface tant que les directives de montage sont respectées. Voir les
explications détaillées dans ce guide.
3. Vérifier la distance à respecter entre les matériaux combustibles ou les objets illuminés et les luminaires VARILITE.
AVERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE LES DÉCHARGES ÉLECTRIQUES
1. Les luminaires VARILITE sont conçus pour une utilisation au sec uniquement. Une exposition à la pluie et à l’humid-
ité risque d’endommager le luminaire.
2. Débrancher l’appareil avant de procéder à la révision de tout matériel VARILITE.
3. Les révisions doivent être effectuées uniquement par des personnes qualifiées.
AVERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE UNE EXPOSITION EXCESSIVE AUX RAY-
ONS UV
1. Plusieurs luminaires VARILITE utilisent une lampe qui produit des rayons UV. NE PAS fixer son regard sur la lampe.
2. L’utilisation des luminaires sans lentille ou blindage pose des risques. Tous blindages, lentilles ou écrans ultraviolet
visiblement endommagés au point que leur efficacité en est affectée doivent être remplacés, par exemple s’il y a des
fissures ou de profondes rayures.
AVERTISSEMENT:
DIRECTIVES POUR SE PROTÉGER CONTRE LES ACCIDENTS POUVANT ENTRAÎNER
DES BLESSURES
1. Les surfaces externes du luminaire deviennent brûlantes quand l’appareil est en marche. Pour manœuvrer ou ajuster des
appareils brûlants et leurs composants, se protéger suffisamment (gants, protection pour les yeux, etc.).
2. La lampe du luminaire est brûlante lorqu’il est en marche. Débrancher le courant et attendre que la lampe ait refroidi
avant de la remplacer.
3. Les lampes à arc émettent des rayons ultraviolets pouvant causer de graves brûlures sur la peau et une inflammation des
yeux. De plus, les lampes à arc fonctionnent sous haute tension à de très hautes températures. Si la lampe se casse, les
particules de la lampe cassée peuvent causer blessures et/ou incendie en s’éparpillant.
4. Se protéger les yeux pour remplacer la lampe.
5. Utiliser des appareils de protection appropriés (gants, protection des yeux) pour manier des lampes endommagées.
6. Si la lampe a été touchée avec des mains nues, la nettoyer avec de l’alcool dénaturé et l’essuyer avec un chiffon non-
pelucheux avant d’installer ou de brancher le luminaire.
ATTENTION Ce symbole annonce que l’appareil risque d’être endommagé.
AVERTISSEMENT Ce symbole annonce qu’il y a risque d’accident grave ou même
fatal.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 6
7. Si la lampe a été endommagée ou a reçu une déformation thermique, elle doit être remplacée.
AVERTISSEMENT:
INTERFÉRENCE RF
Cet appareil est de Classe A. Dans un environnement domestique, cet appareil peut causer des
interférences radio, et si c’est le cas, l’utilisateur peut avoir à prendre des mesures adéquates.
Other
Operational Temperature / Température de fonctionnement
The VL 2600 Profile/Spot/Wash Luminaire has one operational mode. Refer to Table 1-1, “VL 2600
Environmental Operational Temperatures” for information on environment temperature ranges associated
with this mode.
Le VL 2600 Profile/Spot/Wash Luminaire a un mode opérationnel. Reportez-vous à
Table 1-1, “VL
2600 Environmental Operational Temperatures” pour des informations sur les plages de température
environnementales associées à ce mode.
Table 1-1: VL 2600 Environmental Operational Temperatures
Battery Information / Informations sur la batterie
WARNING: This unit has a battery. Warning: Caution risk of explosion if battery
is replaced by an incorrect type. Dispose of used batteries according to the
instructions. AVERTISSMENT: Cet appareil dispose d'une batterie. Attention
risque d'explosion si la batterie de remplacement par un type incorrect. Jetez
les piles usageesselon les instructions.
Part Numbers
Minimum to Maximum Environmental Tem-
perature
CF
-20
o
to 50
o
-4
o
to 122
o
VL 2600 Part Numbers
VL 2600 Profile 88-105-7270-00
VL 2600 Spot 88-105-6950-00
VL 2600 Wash 88-105-7340-00
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
7 29 May 2018 02.1711.0022
About the VL 2600 Profile/Spot/Wash Luminaire
Inc lude d Ite m s
The following illustration shows all items included with the luminaire:
Replacement Items/Accessories
The following optional and/or replacement items can be ordered directly from your Authorized
VARILITE Dealer. When ordering, please order by the Vari-Lite part number.
Note: For approved lamp types, see the latest version of Vari-Lite technical notice TN-248 in the
product downloads section on the Vari-Lite web site, www.Vari-Lite.com
Note: Please check with Vari-Lite or Authorized Vari*Lite Dealer for availability on accessories.
Vari-Lite Part
No.
Accessory
PCT1BE AC Input Cable, Neutrik® powerCON® True1 with Bare End (no connector), 1 Meter
PC1GTL208 AC Input Cable, Neutrik® powerCON® True1 with Twist Lock (Male), 250V, 1 Meter
PCT1GP AC Input Cable, Neutrik® powerCON® True1 with Stage Pin (Male), 1 Meter
PEGASUS Luminaire Programming Software
22.9620.0194 Safety Cable Assembly
25.9661.0057 DMX Termination Connector Assembly
55.6840.0001 Truss Hook, Mega-Clamp, Round and Square
55.6841.0001 Truss Hook, Mega-Claw for 2” Round Tube
Truss Hook Brackets
(truss hooks sold separately)
Neutrik® powerCON TRUE1
AC Input Connector
Warranty Card
Product
Registration
Product Support
QuickStart Guide
Included Items
(this document)
Sheet
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 8
Connecting Power and Data
Connecting Power
The luminaire requires standard AC power distribution from 200-240 VAC, 50/60 Hz. Current
required depends on the AC supply voltage and product model. Refer to
“Current vs. Voltage” on page 9 for
all models covered in this manual.
Note: The mating Neutrik® powerCON® True1 connector is supplied; however, you will need to
purchase or construct a cable appropriate for your application. Available power input cables is found in
“Replacement Items/Accessories” on page 8.
Figure 1: Power Connector
Depending on the application, the luminaire’s AC input cable may require a different connector. If
required, install a new connector meeting your requirements using the following wire color code
reference:
WARNING: DO NOT connect to three-phase service in countries with 240 volt power.
AVERTISSEMENT: NE PAS se connecter au service en trois phases dans les pays avec puissance de
240 volts.
For single-phase power at 240 volts RMS:
For three-phase power at 200 volts RMS:
Wire* Connection
Green/Yellow AC Ground
Blue AC Neutral
Brown AC Line
* International (Harmonized) Standard
Connection Pin
AC Neutral X
AC Line Y
Ground (Earth) G
Connection Pin
Phase 1 X
Phase 2 Y
Ground (Earth) G
AC Power Input
Neutrik® powerCON TRUE1
AC Input Connector
X
Y
G
X
Y
G
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
9 29 May 2018 02.1711.0022
WARNING: It is not recommended to power any VARILITE luminaire from a dimmer - even in
'NONDIM' mode. Dimmer and non-dim modules are not suitable sources of power because their
output modifies the AC wave form. This may work for a short time, but will eventually result in power
problems, luminaire mis-operation and/or failure and may void the luminaire’s warranty.
AVERTISSEMENT: Il n'est pas recommandé pour alimenter un luminaire VARILITE d'un
gradateur - même en mode 'NONDIM’. Modules de gradation et non sombres ne sont pas des sources
appropriées de pouvoir parce que leur production modifie la forme d'onde AC. Cela peut fonctionner
pendant une courte période, mais finira par entraîner des problèmes d'alimentation, luminaires mauvais
fonctionnement et / ou l'échec et peut annuler la garantie de l'appareil.
Cu r re n t vs . Vo lt a g e
Table 1-2, VL 2600 Profile/Spot/Wash Luminaire - Current vs. Voltage (550W Lamp) provides the luminaire’s current
draw at specific voltages. Total Luminaire Current is calculated with the lamp on and all motors
sequencing.
WARNING: It is the responsibility of the user to adequately protect supply source with a correct size and
type circuit breaker and not overload circuits. AVERTISSEMENT: Il est de la responsibilité de
l'utilisateur de protéger adéquatement la source d'alimentation avec une taille correcte et le disjoncteur
de type et surchargez pas les circuits.
Connecting Data
A maximum of 32 luminaires may be connected in any one DMX data link.
Note: This maximum limit applies to the luminaire "daisy chain" only. Your system or console may
require fewer luminaires on a single data link path. Consult your console documentation for more
information.
Table 1-2: VL 2600 Profile/Spot/Wash Luminaire - Current vs. Voltage (550W Lamp)
AC
Voltage
at 60Hz
Total Luminaire Current (Motor + Lamp
Current)
Profile Spot Wash
100V 7.8A 7.5A 7.1A
110V 7.0A 6.7A 6.3A
120V 6.4A 6.1A 5.8A
130V 5.9A 5.6A 5.3A
200V 3.8A 3.6A 3.4A
210V 3.6A 3.5A 3.3A
220V 3.4A 3.3A 3.1A
230V 3.3A 3.2A 3.0A
240V 3.2A 3.1A 2.9A
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 10
To connect power and data:
Step 1. Connect data cable from console to first luminaire in chain at DATA IN connector.
Step 2. If required, connect additional data cables from DATA THRU connectors to DATA IN
connectors of remaining luminaires in link.
Step 3. At last luminaire in link, install male termination connector at DATA THRU connector.
(Luminaires and other devices on the same DMX chain may not function properly without
termination.)
Figure 2: Data Link
Step 4. Connect AC Input Cable connector to power input source.
Step 5. Dress AC input and data cables and secure them so that they will not interfere with
luminaire head and yoke movement.
VL 2600 Profile/Spot/Wash Luminaire Channel Requirements*
DMX512
Channels
Description Menu Display
23 Channels 16-Bit Mode (default) 16
**DMX terminator required for last fixture on DMX line.
Data In
Data Thru
Data Thru
Termination**
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
11 29 May 2018 02.1711.0022
Installation Procedures
Floor Mounting the Luminaire
All luminaires included in this manual are designed to sit directly on its base in a floor installation
application. When used in this type of application, be sure to leave enough space around the luminaire
to allow proper, uninterrupted airflow for cooling and movement.
Ha n g in g t h e Lu m in a ir e
The VL 2600 Profile/Spot/Wash Luminaire can be hung horizontally or vertically from any structure
designed to work with the type of load created by this moving luminaire. Two mounting truss hooks or
other mounting hardware are required. Many compatible truss hooks are available from different
manufacturers for your particular needs.
A minimum of two hooks per luminaire is required. If mounting method does not use truss hooks, two
attachment points, per luminaire, are required.
Install mounting hardware and brackets:
Step 1. Install truss hooks on two provided truss
hook brackets as required as shown in
Figure
3.
Note: Various types of truss hooks can be used. The
Mega Claw truss hook (as shown in the example
above) as well as many other standard hooks, can be
ordered separately.
Step 2. Determine required configuration of bracket
installation. Brackets may be installed in
many different orientations as shown in
Figure 4.
Step 3. While pulling up on locking mechanism
release, fit keyed holes onto raised mounting
buttons at bottom of enclosure. Slide forward and release locking mechanism to lock in
place. Ensure brackets are locked securely.
Mount Bracket
Mega Claw Truss Hook
(not provided)
Truss Hook Hardware
(not provided)
Figure 3: Truss Hook Installation
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 12
WARNING: Ensure that the bracket locking mechanism is fully seated after the bracket is installed on the
luminaire.
Figure 4: Installing Brackets on Luminaire Enclosure
Installing in Truss:
Step 1. Using two people, lift luminaire into mounting position.
Step 2. Secure in place with truss hook. Ensure truss hook hardware that locks hook in place (e.g.
wing bolt) is properly tightened and that luminaire is fully supported.
Step 3. Attach safety cable (as required) as follows (refer to
Figure 5):
a. Loop safety cable at least once around safety cable anchor point rod.
Press up to
Locked
install or release
Locking
Mechanism
Example Truss Hook and Mounting Hardware (not included, sold separately)
Mount
Bracket
Locking
Mechanism
Keyed Hole
Mount Bracket*
Fit bracket’s keyed hole and locking mechanism
over raised mounting buttons and slide forward
to lock.
Brackets
Bracket
Orientation
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
13 29 May 2018 02.1711.0022
b. Loop safety cable at least once around truss/pipe and secure around pipe.
Figure 5: Safety Cable Installation / Luminaire Hanging
Step 4. Make sure tilt and pan locks are disengaged so luminaire moves freely.
Step 5. Connect power and data cables according to procedure given in
“Connecting Data” on page 9.
When hanging the luminaire in a side hang position, orient the enclosure as shown in
Figure 6. Natural
convection and the designed direction of the inlet and exhaust cooling fans dictate that the inlet should
be closest to the floor and the exhaust should be towards the ceiling. This eliminates the possibility of
one luminaire blowing exhaust air into the inlet of the luminaire next to it when the luminaires are
side-by-side.
If the luminaires are stacked on top of one another in a side hang, a 45° enclosure orientation with the
fan inlet closest to the floor is preferred. Refer to
Figure 6.
These two orientations in a side hang have the extra benefit of a stiffer pan interface in the luminaire.
650mm
NOTE: The safety cable anchor point is tested and is in compliance
of the following safety standards:
- IEC / EN 60598-1:2015
Note, truss hooks shown are sold separately. Truss and pipe by others.
Safety Cable Anchor Point
Safety Cable: Recommended for hanging installations. May be required by local codes. Safety cable is sold
separately.
Câble de sécurité: Recommandé pour les installations pendaison. Peut être exigé par les codes locaux.
Câble de sécurité est vendu séparément.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 14
Figure 6: Dual Fixture Side Hang Orientation
When hanging the luminaire in side hang orientation, it is recommended that the Configure/Pan-Tilt/
Side Hang function is enabled. This setting optimizes the performance of the luminaire in side hang
position.
To enable Side Hang function:
Step 1. TBD
Step 2. TBD
Step 3. TBD
Step 4. TBD
Menu Operation
LCD Dis p la y a n d Me n u S ys t e m
The VL 2600 Profile/Spot/Wash Luminaire’s LCD Display and Menu System provides local control
for accessing the following fixture’s settings:
Address – to set the DMX address
Configure – various parameter settings, set luminaire ID
Fixture – fixture status, recalibrate, reboot, software version, view fixtures hours, etc.
DMX – change the map, set address, invert pan/tilt
Service – password protected factory service menu
Manual – manual control of parameters
Test – test functions of parameters
The menu system is controlled at the Menu Display available at the enclosure input panel. If there are
multiple luminaires in a system, any settings or changes would need to be made at each LCD Menu as
desired.
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
15 29 May 2018 02.1711.0022
Menu Controls
The menu system is controlled by an OK (Enter), ESC (Escape), and four Arrow () buttons.
These buttons function are shown in
Figure 7.
Figure 7: Menu Control
LCD Dis p la y a n d Me n u S ys t e m Op e ra t io n
The LCD Display Menu system consists of several categories. Use the Menu Buttons to access and
make changes to the menu items. When the desired menu item is reached, press the desired Menu
Button to display the menu options and to navigate and configure the menu options as required.
To navigate and access menu settings/selections:
Step 1. Make sure unit is powered and turned on.
Step 2. Press [ESC] to access menu categories.
Step 3. Use four Arrow () buttons to navigate through the various options and settings.
Step 4. Once menu item is reached, press OK [Enter] to access the menu item parameters.
Step 5. Make changes to parameters as desired.
Step 6. Press OK [Enter] button to accept changes.
DMX Ad d re s s
To set, edit, and save a DMX address:
Step 1. Press [ESC].
Step 2. Press [Up] / [Down] arrows until
Address (DMX Address) appears. Press OK [Enter].
Step 3. Use [Left] and [Right] arrow buttons to scroll through all digits.
Step 4. Once at desired digit, use [Up] and [Down] arrows to change highlighted digit.
Step 5. Once digit is set, use [Left] and [Right] arrow buttons to set other digits in DMX address.
Step 6. Once all digits are set in DMX address, press OK [Enter] to set.
Step 7. DMX will display and is saved.
LCD Display
OK (Enter) Button
To Select or Change a
Setting or Data Value
Escape (ESC)
Used to Access Main Menu Parameters,
Arrow Keys (Up/Down/Left/Right)
Menu Navigation / Data Selection
Displays all Data and
Luminaire Settings
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 16
Ot h e r LCD Dis p la y Fe a t u r e s
LCD Menu Battery Operation
The LCD menu system utilizes a battery powered system for operation when the luminaire is not
connected to power. The primary purpose of this mode is to allow basic setup and configuration of the
luminaire.
To enable the battery operation of the menu system:
Step 1. Press and hold [ESC] and [OK] for two seconds.
Step 2. Once enabled, the menu will function as normal with only the following sub-menu sections
active:
• Address
• Configure
• Setup
• DMX
• Fixture
Note: Any commands that require full power (calibrate, lamp strike, etc.) will be ignored while the
menu system is in battery operation mode.
Step 3. To exit battery mode, press and hold [ESC] and [OK] for two seconds. Note, luminaire will
automatically exit this mode after one minute of inactivity.
Status Bar
The Status Bar (as illustrated in Figure 8) is present at all times and
displays luminaire operational information of the luminaire. The Status
Bar contains the following information:
LAMP – indicates current lamp state - ON or OFF.
SHDN – indicates shutdown time in hours. NO indicates no
shutdown time.
ERRORS – Displays a number indicating the total amount of
current errors; can cycle through short text descriptions of each
error. Example: “Pan” or “Gobo1”. When errors are present, messages will appear in red text.
When no errors are present, NO will display.
ADDR
– Displays the current DMX address for the fixture. NOTE, when the fixture does not
detect a DMX input signal, the DMX address text will display in red text.
Qu ic k Re fe re n c e DMX Ma p s
The summary list DMX maps for the VL 2600 Profile are indicated in Table 1-3 and Table 1-4.
The summary list DMX maps for the VL 2600 Spot are indicated in Table 1-5 and Table 1-6.
The summary list DMX maps for the VL 2600 Wash are indicated in Table 1-7 and Table 1-8.
Figure 8: LCD Display
Status Bar
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
17 29 May 2018 02.1711.0022
Table 1-3: 16-Bit VL 2600 Profile 16-Bit Enhanced DMX Channel Summary Listing
Table 1-4: 16-Bit VL 2600 Profile 16-Bit DMX Channel Summary Listing
DMX
Channel
Description
DMX
Channel
Description
DMX
Channel
Description
1, 2 Intensity 21 Gobo Wheel 2 (Fixed) 36 Frost
3, 4 Pan 22 Gobo Wheel 2 Control 37 Strobe Speed
5, 6 Tilt 23 Iris 38 Strobe Control
7, 8 Focus 24 Frame 1A 39 Dimmer Mode
9, 10 Zoom 25 Frame 1B 40 Focus Timing
11 Cyan 26 Frame 2A 41 Optics Timing
12 Yellow 27 Frame 2B 42 Color Timing
13 Magenta 28 Frame 3A 43 Beam Timing
14 CTO 29 Frame 3B 44 Gobo Timing
15 Color Wheel 30 Frame 4A 45 Fan Control
16 Color Wheel Control 31 Frame 4B 46 Optical Style
17 Gobo Wheel 1 32 Frame Rotate
47
Luminaire Control
18, 19 Gobo 1 Rot/Index 33 Triangular Prism
20 Gobo Wheel 1 Control 34, 35 Prism Index/Rot
DMX
Channel
Description
DMX
Channel
Description
DMX
Channel
Description
1, 2 Intensity 18, 19 Gobo 1 Rot/Index 31 Frame 4B
3, 4 Pan 20 Gobo Wheel 1 Control 32 Frame Rotate
5, 6 Tilt 21 Gobo Wheel 2 (Fixed) 33 Triangular Prism
7, 8 Focus 22 Gobo Wheel 2 Control 34, 35 Prism Index/Rot
9, 10 Zoom 23 Iris 36 Frost
11 Cyan 24 Frame 1A 37 Strobe Speed
12 Yellow 25 Frame 1B 38 Strobe Control
13 Magenta 26 Frame 2A 39 Dimmer Mode
14 CTO 27 Frame 2B 40 Fan Control
15 Color Wheel 28 Frame 3A 41 Luminaire Control
16 Color Wheel Control 29 Frame 3B
17 Gobo Wheel 1 30 Frame 4A
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
02.1711.0022 29 May 2018 18
Table 1-5: 16-Bit VL 2600 Spot 16-Bit Enhanced DMX Channel Summary Listing
Table 1-6: VL 2600 Spot 16-Bit DMX Channel Summary Listing
Table 1-7: VL 2600 Wash 16-Bit Enhanced DMX Channel Summary Listing
DMX
Channel
Description
DMX
Channel
Description
DMX
Channel
Description
1, 2 Intensity 17 Gobo Wheel 1 31 Frost
3, 4 Pan 18, 19 Gobo 1 Rot/Index 32 Strobe Speed
5, 6 Tilt 20 Gobo Wheel 1 Control 33 Strobe Control
7, 8 Focus 21 Gobo Wheel 2 34 Dimmer Mode
9, 10 Zoom 22, 23 Gobo 2 Rot/Index 35 Focus Timing
11 Cyan 24 Gobo Wheel 2 (Control) 36 Optics Timing
12 Yellow 25 Gobo Wheel 3 (Fixed) 37 Color Timing
13 Magenta 26 Gobo Wheel 3 Control 38 Beam Timing
14 CTO 27 Iris 39 Gobo Timing
15 Color Wheel 28 Triangular Prism 40 Fan Control
16 Color Wheel Control 29, 30 Prism Index/Rot 41 Luminaire Control
DMX
Channel
Description
DMX
Channel
Description
DMX
Channel
Description
1, 2 Intensity 16 Color Wheel Control 28 Triangular Prism
3, 4 Pan 17 Gobo Wheel 1 29, 30 Prism Index/Rot
5, 6 Tilt 18, 19 Gobo 1 Rot/Index 31 Frost
7, 8 Focus 20 Gobo Wheel 1 Control 32 Strobe Speed
9, 10 Zoom 21 Gobo Wheel 2 33 Strobe Control
11 Cyan 22, 23 Gobo 2 Rot/Index 34 Dimmer Mode
12 Yellow 24 Gobo Wheel 2 (Control) 35 Fan Control
13 Magenta 25 Gobo Wheel 3 (Fixed) 36 Luminaire Control
14 CTO 26 Gobo Wheel 3 Control
15 Color Wheel 27 Iris
DMX
Channel
Description
DMX
Channel
Description
DMX
Channel
Description
1, 2 Intensity 15 Frame 1A 25 Strobe Speed
3, 4 Pan 16 Frame 1B 26 Strobe Control
5, 6 Tilt 17 Frame 2A 27 Dimmer Mode
7, 8 Focus 18 Frame 2B 28 Focus Timing
9 Cyan 19 Frame 3A 29 Optics Timing
10 Yellow 20 Frame 3B 30 Color Timing
11 Magenta 21 Frame 4A 31 Fan Control
12 CTO 22 Frame 4B 32 Luminaire Control
13 Color Wheel 23 Frame Rotate
14 Color Wheel Control 24 Frost
VARILITE - VL 2600 PROFILE/SPOT/WASH LUMINAIRE QUICKSTART GUIDE
19 29 May 2018 02.1711.0022
Table 1-8: VL 2600 Wash 16-Bit DMX Channel Summary Listing
DMX
Channel
Description
DMX
Channel
Description
DMX
Channel
Description
1, 2 Intensity 13 Color Wheel 21 Frame 4A
3, 4 Pan 14 Color Wheel Control 22 Frame 4B
5, 6 Pan 15 Frame 1A 23 Frame Rotate
7, 8 Zoom 16 Frame 1B 24 Frost
9 Cyan 17 Frame 2A 25 Strobe Speed
10 Yellow 18 Frame 2B 26 Strobe Control
11 Magenta 19 Frame 3A 27 Dimmer Mode
12 CTO 20 Frame 3B 32 Luminaire Control
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Vari Lite VL 2600 Guide de démarrage rapide

Catégorie
Stroboscopes
Taper
Guide de démarrage rapide
Ce manuel convient également à

dans d''autres langues