Bunn ITB-DBC Le manuel du propriétaire

ITB/ITCB

ITCB-DV HV

ITCB TWIN HV

Infusion Series

®

INSTALLATION & OPERATING GUIDE

BUNN-O-MATIC CORPORATION OF CANADA

280 INDUSTRIAL PARKWAY S.,

AURORA, ONTARIO, L4G 3T9

PHONE: (905) 841-2866 FAX: (905) 263-2256

To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts

Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at

www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and

manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.

2

36748.3 080112

392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN

Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic,

Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design,

Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, In-

tellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with

the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel,

Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh,

Titan, trifecta, Velocity Brew, A Partner You Can Count On, Air Brew, Air Infusion, Beverage Bar Creator, Beverage Proﬁt

Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control,

Nothing Brews Like a BUNN, Pouring Proﬁts, Signature Series, Tea At Its Best, The Horizontal Red Line, Ultra are either

trademarks or registered trademarks of Bunn-O-Matic Corporation.

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corporation of Canada (“Bunn”) warrants equipment manufactured by it as follows:

1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers

thermal servers and Thermofresh servers (mechanical and digital) - 1 year parts and 1 year labour.

2) All other equipment - 2 years parts and 1 year labour plus added warranties as speciﬁed below:

a) Electronic circuit and/or control boards - parts and labour for 3 years.

b) Compressors on refrigeration equipment - 5 years parts and 1 year labour.

c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve

analysis - parts and labour for 4 years or 40,000 pounds of coffee, whichever comes ﬁrst.

These warranty periods run from the date of installation. Bunn warrants that the equipment manufactured

by it will be commercially free of defects in material and workmanship existing at the time of manufacture and

appearing within the applicable warranty period. This warranty does not apply to any equipment, component

or part that was not manufactured by Bunn or that, in Bunn’s judgement, has been affected by misuse, neglect,

alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and descaling,

equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not apply to

replacement of items subject to normal use including but not limited to user replaceable parts such as seals and

gaskets. This warranty is conditioned on the Buyer 1) giving Bunn prompt notice of any claim to be made under

this warranty by telephone at (905) 841-2866 or by writing to 280 Industrial Parkway South, Aurora, Ontario, L4G

3T9. 2) if requested by Bunn, shipping the defective equipment prepaid to an authorized Bunn service location;

and 3) receiving prior authorization from Bunn that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, CONDITION,

WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY

OF EITHER MERCHANTABILITY, MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE.The

agents, dealers or employees of Bunn are not authorized to make modiﬁcations to this warranty or to make

additional warranties that are binding on Bunn. Accordingly, statements by such individuals, whether oral or

written, do not constitute warranties and should not be relied upon.

If Bunn determines in its sole discretion that the defective equipment is covered by warranty, Bunn, at its

exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts

and/or labour (during the applicable parts and labour warranty periods speciﬁed above) to repair the defective

components, provided that this repair is done by a Bunn Authorized Service Representative; or 2) shall replace

the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE

SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT

BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost proﬁts, lost

sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute

equipment, facilities or services, or any other special, incidental, consequential or punitive damages.

RETURN POLICY

CONTACT PLANT FOR RETURN MATERIAL AUTHORIZATION. ALL RETURNS MUST

BE AUTHORIZED BY BUNN-O-MATIC AND ARE SUBJECT TO A RETURN CHARGE.

3

INTRODUCTION

ITB

This equipment will brew tea into an awaiting dispenser or reservoir.

The ITB uses recipe settings to brew tea. It has an LCD for digital readout and programming. The user is able

to select regular or quick brew for tea programming. Other features include Pre-Infusion and Pulse Brew, quick

and standard brew, Energy Savings mode, BUNNLink compatible, Freshness Timer, Sanitation Alert, and brew

counters. Available in low proﬁle, dual dilution and sweetener models.

ITCB-DV/ITCB-DV HV

This equipment will brew either tea or coffee into an awaiting dispenser or reservoir. It can be easily conﬁgured

for 120V or 120/208V-120/240V (Refer to data plate for speciﬁc ratings). The brewer may have an auxiliary hot

water faucet that can be mounted on the front, left or right side.

ITCB HV TWIN

This equipment will brew either tea or coffee into an awaiting dispenser or reservoir in either the left or right

side brewing station. The brewer may have an auxiliary hot water faucet that can be mounted on the front, left

or right side.

This equipment is only for indoor use on a sturdy counter or shelf.

The Infusion Series combines BrewWISE, CDBC and Tea Brewers into one. ITCB is able to brew both tea

and coffee with recipe settings. It has an LCD for digital readout and programming along with the Smart Funnel

options for coffee. The user is able to select regular or quick brew for tea programming. Other features include:

Pre-Infusion, Pulse Brew, quick and standard brew, and BrewWISE, Energy Savings mode, BUNNLink compatible,

Smart Reader compatible, Freshness Timer, Sanitation Alert, and sweetener with low product detection.

CONTENTS

Warranty .............................................................................................................2

Introduction ........................................................................................................3

User Notices .......................................................................................................4

Electrical Requirements (ITB/ITCB-DV) ...............................................................5

Electrical Requirements (ITCB-DV HV/TWIN) .....................................................6

Plumbing Requirements/Optional Sweetener ......................................................7

Operating Controls ..............................................................................................8

Initial Set-Up .......................................................................................................9

Tea Brewing ......................................................................................................10

Coffee Brewing ..................................................................................................10

Cleaning/Tank Drain ..........................................................................................11

Sanitizing Optional Sweetener ...........................................................................12

Programming ....................................................................................................13

ITB ...................................................................................................................120V Infusion Tea Brewer

ITB-DD ................................................................................................................................. Dual Dilution

ITB-LP ...................................................................................................................... Low Proﬁle Machine

ITCB-DV ................................................................................................................................Dual Voltage

ITCB-DV HV .................................................................................................... Dual Voltage High Volume

ITCB-C-DV ..............................................................................................Dual Voltage Brewer for Canada

ITCBA .............................................................................................................................. 230 Volt Brewer

ITCBB .............................................................................................................................. 200 Volt Brewer

TWIN ................................................................................................................................ 2 Brew Stations

36748.3 062111

4

USER NOTICES

Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should

be kept in good condition. Replace any unreadable or damaged labels.

#34072.0000 ITCB

#03408.7002

#03409.7002

Artwork for P/N: 00656.7000

Artwork Rev: F

Drawn: RN

Date: 06/27/08

Cet équipement doit être installé conformément au code

Canadien de plomberie et aux règlements de santé et de

sécurité qui s’ appliquent. Les modèles destinés à être

installés ailleurs qu’au Canada doivent respecter les codes de

plomberie et d’hygiène de la localité.

This equipment must be installed to comply with Canadian

Plumbing Codes and applicable health and safety regulations.

For models installed outside Canada, comply with the

applicable Plumbing /Sanitation Code.

#00986.7000 ITCB

#37881.7000

#00658.7000

#00656.7000

#39175.7000

36748.3 112912

#00831.0002 ITB

! AVERTISSEMENT

! WARNING

• FILL WATER TANK BEFORE PLUGGING IN UNIT OR

ENERGIZING THE THERMOSTAT.

• DO NOT OVERLOAD CIRCUIT.

• ALWAYS ELECTRICALLY GROUND THE CHASSIS.

• DO NOT DEFORM PLUG OR CORD.

• FOLLOW NATIONAL AND LOCAL ELECTRICAL CODES.

• KEEP COMBUSTIBLES AWAY.

FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE OR

SHOCK HAZARD.

READ THE ENTIRE OPERATING MANUAL INCLUDING

THE LIMIT OF WARRANTY AND LIABILITY BEFORE

BUYING OR USING THIS PRODUCT.

THIS EQUIPMENT IS ENERGIZED AT ALL TIMES UNLESS

ELECTRICALLY DISCONNECTED.

• REMPLIR LE RÉSERVOIR D'EAU AVANT DE BRANCHER

L'APPAREIL OU DE METTRE LE THERMOSTAT SOUS TENSION.

• NE PAS SURCHARGER LE CIRCUIT.

• TOUJOURS METTRE LE BOITIER À LA MASSE.

• NE PAS DÉFORMER LA FICHE OU LE CORDON.

• SE CONFORMER AUX CODES NATIONAL OU LOCAL

D'ÉLECTRICITÉ.

• GARDER LES PRODUITS COMBUSTIBLES À DISTANCE.

TOUT MANQUEMENT À SE CONFORMER À CES DIRECTIVES PEUT

ENTRAINER DES DOMMAGES À L'ÉQUIPEMENT OU PRODUIRE DES

DANGERS D'INCENDIE OU D'ÉLECTROCUTION.

VEUILLEZ LIRE LE MANUEL DE FONCTIONEMENT

EN ENTIER, Y COMPRIS LES LIMITES DE GARANTIES ET

RESPONSABILITÉS,AVANT D’ACHETER

OU D'UTILISER LE PRÉSENT PRODUIT.

L' ÉQUIPEMENT EST TOUJOURS SOUS TENSION

LORSQU'IL N'EST PAS DÉBRANCHÉ.

#00824.0001

(CE ONLY)

#00824.0002

#38125.0000 TWIN

WARNING

FAILURE TO COMPLY RISKS EQUIPMENT

DAMAGE, FIRE OR SHOCK HAZARD.

READ THE ENTIRE OPERATING MANUAL INCLUDING

THE LIMIT OF WARRANTY AND LIABILITY BEFORE

BUYING OR USING THIS PRODUCT.

AVERTISSEMENT

• DO NOT OVERLOAD CIRCUIT.

• ALWAYS ELECTRICALLY GROUND THE CHASSIS.

• DO NOT DEFORM PLUG OR CORD.

• FOLLOW NATIONAL AND LOCAL

ELECTRICAL CODES.

• KEEP COMBUSTIBLES AWAY.

THIS EQUIPMENT IS ENERGIZED AT ALL TIMES UNLESS

ELECTRICALLY DISCONNECTED.

• NE PAS SURCHARGER LE CIRCUIT.

• TOUJOURS METTRE LE BOÎTIER À LA MASSE.

• NE PAS DÉFORMER LA FICHE OU LE CORDON.

• SE CONFORMER AUX CODES NATIONAL OU

LOCAL D'ÉLECTRICITÉ.

• GARDER LES PRODUITS COMBUSTIBLES À

DISTANCE.

TOUT MANQUEMENT À SE CONFORMER À CES

DIRECTIVES PEUT ENTRAINER DES DOMMAGES

À L'ÉQUIPEMENT OU PRODUIRE DES DANGERS

D'INCENDIE OU D'ÉLECTROCUTION.

VEUILLEZ LIRE LE MANUEL DE FONCTIONEMENT EN

ENTIER, Y COMPRIS LES LIMITES DE GARANTIES ET

RESPONSABILITÉS,AVANT D’ACHETER OU

D'UTILISER LE PRÉSENT PRODUIT.

L' ÉQUIPEMENT EST TOUJOURS SOUS TENSION LORSQU'IL

N'EST PAS DÉBRANCHÉ.

For 120/208V or 120/240 volt operation,

replace Power Supply Cord only with

Bunn-O-Matic part number 01699.0000.

! CAUTION

Incorrect programming could result in accidental dispensing of HOT

LIQUID. Trained personnel are to follow instructions provided for

soft- ware programming. Use of additional graphic layer requires

disabling of appropriate switches. Read all instructions for additional

graphic layer prior to installing and programming.

WARNING AVERTISSEMENT

Une programmation incorrecte peut donner accidentellement une

distribution d'EAU CHAUDE. Personnel qualifié peut suivre les

instructions fournies pour la programmation du logiciel. Utilisation

d'un graphique additionnel supplémentaire requiert une mise hors

d'usage de certains interrupteurs appropriés.

Lire toutes les instructions concernant les graphiques

additionnels avant l'installation et la programmation.

Risk of Fire. Use a UL listed grounding

type attachment plug, rated 125/208

Vac, 30 A, 1 phase, 4 conductor. Plug

to be selected and installed only by

qualified service personnel.

Artwork for P/N: 00658.7000

Artwork Rev: G

Updated by: RN

Date: 02/16/10

Colors:

PANTONE 1375 C

PANTONE 108 C

Funnel and hand to be white

PANTONE Process Black C

READ THE ENTIRE OPERATING MANUAL BEFORE USING THIS PRODUCT.

FAILURE TO COMPLY RISKS INJURY.

VEUILLEZ LIRE LE MANUEL D’EMPLOI AVANT D’UTILISER CE PRODUIT.

L’INOBSERVATION DE CES CONSEILS PEUT ENTRAÎNER DES RISQUES DE BLESSURE.

LE CONTENU

DE L’ENTONNOIR

EST CHAUD

FUNNEL CONTENTS

ARE HOT

DISCARD DECANTER

IF:

• CRACKED

• SCRATCHED

• BOILED DRY

• HEATED WHEN EMPTY

• USED ON HIGH FLAME

OR EXPOSED ELECTRIC

ELEMENTS

JETER LA CARAFE :

• SI ELLE EST FISSURÉE

• SI ELLE EST RAYÉE

• SI ON A LAISSÉ DE L’EAU

S’ÉVAPORER PAR

ÉBULLITION

• SI ELLE A ÉTÉ CHAUFFÉE À VIDE

• SI ELLE A ÉTÉ UTILISÉE SUR

UNE FLAMME VIVE OU SUR

DES ÉLÉMENTS ÉLECTRIQUES

DÉCOUVERTS

WARNING / AVERTISSEMENT

To reduce the risk of electric shock, do not remove or

open cover. No user-serviceable parts inside.

Authorized service personnel only. Disconnect power

before servicing.

Afin d’éviter un risque d’électrocution, ne pas ouvrir ou

enlever le panneau. Aucune pièce utile pour

l’opérateur à l’intérieur. Seulement le personnel

autorisé peut effectuer les réparations. Débrancher de la

source de courant avant d’effectuer une réparation.

WARNING AVERTISSEMENT

WARNING/AVERTISSEMENT

REMOVE

FUNNEL

SLOWLY

RETIRER

L’ENTONNOIR

LENTEMENT

LIQUIDE

CHAUD

WARNING/AVERTISSEMENT

HOT

LIQUID

M

a

k

e

s

u

r

e

F

u

n

e

l

i

s

r

o

t

a

t

e

d

a

n

d

a

l

i

g

n

e

d

w

i

t

h

M

a

k

e

s

u

r

e

F

u

n

e

l

i

s

r

o

t

a

t

e

d

a

n

d

a

l

i

g

n

e

d

w

i

t

h

T

e

a

D

i

s

p

e

n

s

e

r

o

n

t

h

e

R

I

G

H

T

s

i

d

e

t

o

a

v

o

i

d

T

e

a

D

i

s

p

e

n

s

e

r

o

n

t

h

e

L

E

F

T

s

i

d

e

t

o

a

v

o

i

d

p

o

t

e

n

t

i

a

l

b

u

r

n

s

a

n

d

w

a

t

e

r

s

p

i

l

s

.

R

I

G

H

T

p

o

t

e

n

t

i

a

l

b

u

r

n

s

a

n

d

w

a

t

e

r

s

p

i

l

s

.

L

E

F

T

W

A

R

N

I

N

G

H

O

T

L

I

Q

U

I

D

S

#41995.0000 ITB DD

5

ELECTRICAL HOOK-UP (All Models)

CAUTION – Improper electrical installation will damage electronic components. Damage caused by incorrect

electrical connections is not covered by warranty.

1. An electrician must provide electrical service.

2. Determine the available on-site electrical service.

3. (Steps 3 & 9 apply to DV models only) Select the desired unit voltage based on the available on-site

electrical service.

4. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

5. Remove the back panel to gain access to the terminal block.

6. Feed the power cord through the strain relief and connect it to the terminal block(s).

7. Connect the power cord to the terminal block as shown.

8. Before proceeding, verify the voltage at the ﬁeld wiring terminal block.

9. Set voltage switch to the appropriate position and replace the access panel.

10. If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing

has been hooked up, the brewer is ready for Initial Set-Up.

ELECTRICAL REQUIREMENTS ITB & ITCB-DV

WARNING - The brewer must be disconnected from the power source until speciﬁed.

WARNING - The power cord must be CSA Listed, Flexible Cord Type SO, SJO, SJTO, HSJO or SJOW, Rated 90° C,

and the attachment plug cap must be UL Listed, in order to avoid a hazard. The Power Supply Cord must

be at least 3 feet long and maximum 6 feet long (measured from Strain Relief to end of the Attachment

Plug Cap).

ITB - 120V models require 2-wire, grounded service rated 120 volts AC, 15 amp, single phase, 60Hz.

Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit

requirements.

120/208-240V 3 WIRE + GROUND 120V 2 WIRE + GROUND

240V 2 WIRE + GROUND

ITCB DV

ONLY

220-240V 2 WIRE + GROUND

36748.3 120312

“Optional Field Wiring ratings are located on the machine near the dataplate.”

N

L1

G

L2 RED L2 RED

POWER CORD

WHITE

GREEN

NEUTRAL

L1 BLACK

WHITENEUTRAL

L2

L1 BLACK

WHITE

NEUTRAL

L1 BLACK

N

L1

G

POWER CORD

GREEN

WHITENEUTRAL

L1 BLACK

L2 RED L2 RED

L2

L1 BLACK

L1

G

POWER CORD

GREEN

L1 BLACK

L2 RED NEUTRAL BLUE

N

L1 BLACK

L1

G

POWER CORD

GREEN/YELLOW

L1 BROWN

DUAL VOLT

TOGGLE SWITCH

6

ELECTRICAL HOOK-UP (All Models)

CAUTION – Improper electrical installation will damage electronic components. Damage caused by incorrect

electrical connections is not covered by warranty.

1. An electrician must provide electrical service.

2. Determine the available on-site electrical service.

3. (Steps 3 & 9 apply to DV models only) Select the desired unit voltage based on the available on-site

electrical service.

4. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

5. Remove the front panel to gain access to the terminal block.

6. Feed the power cord through the strain relief and connect it to the terminal block.

7. Connect the power cord to the terminal block as shown.

8. Before proceeding, verify the voltage at the ﬁeld wiring terminal block.

9. Set voltage switch to the appropriate position and replace the access panel.

10. If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing

has been hooked up, the brewer is ready for Initial Set-Up.

ELECTRICAL REQUIREMENTS ITCB-DV HV & TWIN

DUAL VOLT

TOGGLE SWITCH

WARNING - The brewer must be disconnected from the power source until speciﬁed.

WARNING - The power cord must be CSA Listed, Flexible Cord Type SO, SJO, SJTO, HSJO or SJOW, Rated 90° C,

and the attachment plug cap must be UL Listed, in order to avoid a hazard. The Power Supply Cord must

be at least 3 feet long and maximum 6 feet long (measured from Strain Relief to end of the Attachment

Plug Cap).

ITCB HV TWIN - requires 3-wire, grounded service rated 120/208-240 volts AC, 30 amp, single phase,

60Hz.

ITCB-DV HV - 120V models require 2-wire, grounded service rated 120 volts AC, 15 amp, single phase,

60Hz. or 3-wire, grounded service rated 120/208-240 volts AC, 20 amp, single phase, 60Hz.

Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit

requirements.

120/208-240V 3 WIRE + GROUND 120V 2 WIRE + GROUND

ITCB-DV HV

ITCB-DV HV & TWIN ITCB-DV HV ONLY

Terminal

Block

ITCB-DV HV TWIN

36748.3 113010

“Optional Field Wiring ratings are located on the machine near the dataplate.”

N

L1

G

L2 RED L2 RED

POWER CORD

WHITE

GREEN

NEUTRAL

L1 BLACK

WHITENEUTRAL

L2

L1 BLACK

WHITE

NEUTRAL

L1 BLACK

N

L1

G

POWER CORD

GREEN

WHITENEUTRAL

L1 BLACK

7

OPTIONAL SWEETENER

Connect sweetener line to ﬁtting on back of brewer labeled "SWEETENER".

NOTE: Operating range for sweetener is 25-60psi, 35psi recommended.

CE Requirements:

• This appliance must be installed in locations where it can be overseen by trained personnel.

• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.

• Appliance shall not be tilted more than 10° for safe operation.

• An electrician must provide electrical service as specied in conformance with all local and national codes.

• This appliance must not be cleaned by water jet.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of

this appliance by a person responsible for its safety.

• Children should be supervised to ensure they do not play with the appliance.

• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with

a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.

PLUMBING REQUIREMENTS

These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138

and 620 kPa) from a 1/2˝ or larger supply line. A shut-off valve should be installed in the line before the brewer.

Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa).

The water inlet ﬁtting is .75-11.5 NH (HOSE THREAD). For convenience an elbow adaptor is provided to convert

to a 1/4˝ ﬂare ﬁtting (3/8˝ ﬂare on Twins). Bunn-O-Matic does not recommend the use of a reverse-osmosis or

deionized water supply to this equipment. REQUIRED: 1.25 gpm (4.73 lpm) ﬂow rate from water supply line.

NOTE - Bunn-O-Matic recommends 3⁄8" copper tubing for all installations from the 1⁄2" water supply line. A tight

coil of tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not

recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply

line by this type of device may restrict water ﬂow.

Plumbing Hook-Up

1. Remove the shipping cap from the ﬁtting on the rear of the brewer.

2. STANDARD MODELS: Securely attach adaptor elbow assembly to the .75-11.5 NH (HOSE THREAD) ﬁtting

at the rear of the brewer.

TWIN MODELS: Securely attach the tube assembly (supplied in parts box) to water supply line. Securely

attach the elbow assembly to the .75-11.5 NH (HOSE THREAD) ﬁttings at the rear of the brewer. Connect the

tube assembly to the elbows.

3. Flush the water line and Securely attach it to the adaptor elbow.

4. Turn on the water supply.

36748.3 062111

This equipment must be installed to comply with the National Plumbing Code of Canada and the

Canadian Food Inspection Agency. For models installed outside Canada, you must comply with the

applicable Plumbing/Sanitation Code for your area.

8

OPERATING CONTROLS

A. ENABLE BREW (ON/OFF) SWITCH

Pressing the ENABLE BREW (ON/OFF) switch pad will alternately turn the brewer on and off. Pressing this

pad during the brew cycle will interrupt the brew cycle, stopping the ﬂow of water. Pressing this pad during

programming of the brewer will exit the setup and return to the main screen.

B. PROGRAMMING (left)

This hidden pad can be used to scroll backwards through the function list while in programming mode.

C. BREW (A,B,C) and FUNCTION

When the ENABLE BREW is ON and the brewer is on the main screen (not in programming mode),

momentarily pressing and releasing this pad will begin a brew cycle. These are also used to program the brewer

when in the programming mode.

D. PROGRAMMING (right)

Pressing and holding this pad allows entry into the programming menus. Pressing and releasing the pad

steps through each function screen while in the programming mode.

E. BATCH SELECTOR PADS

Pressing the pad corresponding to the Half or Full batch selects the amount of product to be brewed. Pressing

a different pad after a brew cycle has been initiated does not change the brew batch in progress. Light indicates

the selected batch to brew. Also used in programming to adjust settings on both batch sizes.

F. FUNCTION SCREEN

This is the display which shows the various functions of the brewer and allows the programming to be

accomplished.

G. FUNNEL SENSING COIL (ITCB ONLY)

This is used to "receive" information from the Smart Funnel handle, recipe cards, and ad cards.

H. FUNCTION SCREEN SWITCHES

Digital: This is used to select options (NO/-) that appear on the display during programming.

Brewer: This is used to select options (DONE) that appear on the display during programming.

Control: This is used to select options (YES/+) that appear on the display during programming.

ITB ITCB-DV & HV

36748.3 111010

ITCB-TWIN HV

HALF

FULL

BREW

A

BREW

B

BREW

C

®

ENABLE

ON / OFF

BREW

G

D

B

C

A

F

E

D

B

C

A

F

E

ENABLE

ON / OFF

ENABLE

ON / OFF

BREWBREW

®

D

B

A

F

A

E

G

C

G

C

H

9

1. Insert an empty funnel into the funnel rails.

2. Place an empty server under the funnel.

3. Connect the brewer to the power source. Make sure

the ON/OFF switch is ON (LED will be lit).

4. Water will ﬂow into the tank and stop when the tank

is ﬁlled to its capacity. Display will show PLEASE

WAIT...TANK FILLING until tank is ﬁlled with water.

5. Wait approximately twenty minutes for the water in

the tank to heat to the proper temperature. Display

will show READY TO BREW...WATER TEMP: 205°

when tank is at operating temperature. Some water

will drip from the funnel during this time; this is due

to expansion and should not occur thereafter.

6. MODELS w/FAUCET: Place a small container beneath

the faucet and open the faucet handle. Release it when

you hear the tank reﬁlling.

7. Water volumes and ﬂow settings have been preset at

the factory. Refer to the Programming Manual should

the volume need to be increased or decreased.

8. The brewer is now ready for use in accordance with the

instructions for Tea Brewing and Coffee Brewing.

VIEWING ASSIGNED RECIPES

1. Make sure the ON/OFF switch is OFF (LED will not be lit).

2. Press and hold BREW A. The display will show the name of the recipe assigned to Brew A along with SWITCH

NOT ON. This is to indicate that a brew cannot be initiated while the ON/OFF switch is OFF.

3. Repeat for BREW B and BREW C.

4. (Twins only) Repeat steps 1 -3 for other side.

5 Make sure the "ENABLE BREW ON/OFF" switch is OFF. To view the asset number of the machine, press and

hold the left hidden button until the display reads: ANXXXXXX...ASSET NUMBER. Release the left hidden

button.

6. After a 5 second delay, the display will read: ITCBXXXXXXX. This is the serial number of the machine.

INITIAL SET-UP

36748.3 111010

205° F (96.1° C)

10

TEA BREWING

1. Begin each brew cycle with a clean empty brew funnel and server. (Be sure the server lid doesn’t interfere

with the ﬂow of dilution water.)

2. Insert a BUNN ﬁlter into the funnel.

3. Pour the packet of loose fresh tea leaves into the ﬁlter. Approximately three to ﬁve ounces is recommended

for three gallons of beverage.

4. Level the bed of tea leaves by gently shaking.

5. Slide the funnel into the funnel rails until it stops. On dual dilution models, rotate the funnel handle left or

right to align the funnel discharge over the reservoir.

6. The ON/OFF must be ON. Select which batch size to brew.

7. Momentarily press and release the assigned BREW switch. There may be certain situations in which the

brew cycle will not begin when BREW is pressed:

a. SWITCH NOT ON - ON/OFF must be ON.

b. BREW TEMPERATURE TOO LOW – wait until heated or cancel BREW LOCKOUT option.

c. CHECK FUNNEL – remove funnel, empty previously brewed leaves and replace with fresh tea leaves.

d. DISABLED - select different brew switch or batch size.

8. If none of the above messages are displayed, the display will read NOW BREWING and show the time

remaining in the brew cycle.

9. Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the

tea no longer drips from the funnel tip.

10. Carefully remove the brew funnel and discard the tea leaves and ﬁlter only after visible dripping stops.

COFFEE BREWING (ITCB/HV ONLY)

WITHOUT A SMART FUNNEL AND G9-2T DBC GRINDER:

1. Begin each brew cycle with a clean empty brew funnel.

2. Insert a BUNN ﬁlter into the funnel.

3. Pour the fresh coffee into the ﬁlter and level the bed of grounds by gently shaking.

4. Slide the funnel into the funnel rails until it stops.

5. Place an empty server under the funnel.

6. The ON/OFF must be ON. Select the FULL batch size.

7. Momentarily press and release the assigned BREW switch. There may be certain situations in which the brew

cycle will not begin when BREW is pressed:

a. SWITCH NOT ON - ON/OFF must be ON.

b. BREW TEMPERATURE TOO LOW – wait until heated or cancel BREW LOCKOUT option.

c. CHECK FUNNEL – remove funnel, empty previously brewed grounds and replace with fresh.

d. DISABLED - select different brew switch or batch size.

e. COFFEE FUNNEL? – appears when brew volume is greater than 86.0 oz. (2.54 L) and pulse brew is

disabled. Check to make sure the correct funnel is in place, and then press BREW again.

8. If none of the above messages are displayed, the display will read NOW BREWING and show the time remaining

in the brew cycle.

9. Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the

coffee no longer drips from the funnel tip.

10. Carefully remove the brew funnel and discard the grounds and ﬁlter only after visible dripping stops.

WITH A SMART FUNNEL AND G9-2T DBC or MHG GRINDER: (ITCB/HV ONLY)

1. Select the small batch size on the grinder.

2. Insert a BUNN ﬁlter into the funnel.

3. Grind the selected amount of fresh coffee into the Smart Funnel using the G9-2T DBC or MHG with Smart

Funnel operation and level the grounds by gently shaking.

36748.3 111010

11

4. Slide the funnel into the funnel rails. The brewer will read the coffee name and size ground through the chip

in the funnel handle.

NOTE: The brewer will automatically match the brew batch size to the grinder batch size:

GRINDER BREWER

Small Half Batch

Medium Full Batch

Large *Full Batch

*If BREW is pressed with a large grinder batch, the display will read: INCORRECT GRIND...BATCH SIZE WRONG,

and then PRESS BREW TO BREW ANYWAY.

5. Place an empty server under the funnel.

6. The ON/OFF must be ON.

7. Momentarily press and release the assigned BREW switch. There may be certain situations in which the brew

cycle will not begin when BREW is pressed:

a. SWITCH NOT ON - ON/OFF must be ON.

b. BREW TEMPERATURE TOO LOW – wait until heated or cancel BREW LOCKOUT option.

c. CHECK FUNNEL – remove funnel, empty previously brewed grounds and replace with fresh.

d. INCORRECT GRIND - Indicates a large batch was ground using the grinder. Check batch size and grind

weight.

8. If none of the above messages are displayed, the display will read NOW BREWING and show the time remaining

in the brew cycle.

9. Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the

coffee no longer drips from the funnel tip.

10. Carefully remove the brew funnel and discard the grounds and ﬁlter only after visible dripping stops.

CLEANING

CAUTION – CLEAN AND SANITIZE YOUR ICED TEA BREWER DAILY

1. Remove and thoroughly clean the entire brew funnel. The funnel tip and screen must be free from any tea

particles or residue. Reassemble the funnel.

2. Remove and thoroughly rinse the sprayhead. The holes must be open and clear of any mineral deposits. Wipe

the sprayhead panel clean with a damp cloth.

NOTE – Any buildup on the sprayhead may restrict water ﬂow, and impact your brewing. For consistently great

tea and coffee, clean sprayhead weekly with sprayhead cleaning tool (#38227.0000). Upon visual inspection it

may appear that light passes through all holes in the sprayhead, but a thin ﬁlm of residue can pass light and still

impede water ﬂow.

a. Remove sprayhead from brewer.

b. Use the pointed end of sprayhead cleaning tool to remove any mineral deposits from the sprayhead holes.

c. Insert the long end of sprayhead cleaning tool into the sprayhead ﬁtting, and rotate several times to

remove any mineral deposits from the ﬁtting.

3. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all

surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device.

CAUTION – DO NOT KEEP BREWED ICED TEA OVERNIGHT. THE SERVER MUST BE CLEANED DAILY.

36748.3 092712

TANK DRAIN

1. Remove back access cover (front cover on HV).

2. Close the white shutoff clamp on the long hose between tank and inlet solenoid.

3. Disconnect the hose clamp and hose from inlet solenoid or check valve.

4. Place the end of the drain hose in a container that has a minimum capacity of 2.0 gallons (7.5 L) ITB/ITCB,

[3.5Gal/13.25L for HV single or 6.0Gal/22.7L for HV Twin].

5. Release the white clamp to drain water from the tank.

6. When tank is empty, replace the hose onto solenoid (or ﬂow control) and tighten the black clamp.

7. Replace the access cover.

8. On HV units, use care so you do not pinch the dilution hoses when replacing cover.

12

SANITIZING OPTIONAL SWEETENER

All Models:

1. Remove all the quick disconnects (QCD) from all the B.I.B. containers.

2. Fill a suitable pail or bucket with a warm soapy tap water solution. (140° F)

3. Submerge all disconnects (gas and liquid) in the soapy solution and then clean them using a nylon bristle

brush. (Do not use a wire brush). Rinse with clean water.

4. Using a plastic pail, prepare approximately ﬁve (5) gallons of Kay-5 (or equivalent) sanitizing solution with at

least 100 ppm of available chlorine in 120° F water.

5. Rinse the B.I.B. disconnects (QCD’s) in the sanitizing solution.

6. Special sanitizing ﬁttings must be attached to each B.I.B. disconnect (QCD’s). If these ﬁttings are not available,

the ﬁttings from empty B.I.B. bags can be cut from the bags and used. These ﬁttings open the “disconnect”

so the sanitizing solution can be drawn through the disconnect opening.

7. Place all the B.I.B. disconnects (QCD’s) into the pail of sanitizing solution.

Models with factory installed sweetener:

8. Press and hold the left hidden switch until the display reads: "SanitizeSweetnr?" Press "YES". Next screen will

ask "CONTAINER READY?"

9. Press "YES". Allow solution to ﬂow from dilution nozzle for a few seconds.

10. Press any brew switch to stop. Display will read "SOAKING" and count down from 15 minutes. Display will

now read "SOAP PURGE"

11. Remove the special sanitizing ﬁttings, or empty, cut B.I.B ﬁttings from the B.I.B. disconnects (QCD’s) and

re-connect the QCD ﬁttings to the appropriate B.I.B. container. (You will now begin the process of bringing

syrup back through the system)

a. Place empty tea dispenser under unit

b. Place empty brew basket into funnel rails

12. Press "START". Next screen will ask "CONTAINER READY?"

13. Press "YES". Continue with brew cycle until syrup is ﬂowing freely from the dilution nozzle.

14. Press any brew switch to stop. Display will read "SANITAION COMPLETE" and return to home screen.

Models with ﬁeld installed sweetener kit:

8. The next steps are to initiate a brew cycle and draw sanitizer through the system:

a. Place empty tea dispenser under unit.

b. Place empty brew basket into funnel rails

c. Push appropriate brew button for Sweet Tea (brew cycle will initiate)

d. Continue with brew cycle until the sanitizing solution is ﬂowing from the dilution nozzle.

e. Push the “Enable Brew on/off” button to stop the brew cycle and then push again to cancel the brew

cycle

f. Allow sanitizer to remain in lines for ﬁfteen (15) minutes.

9. Remove the special sanitizing ﬁttings, or empty, cut B.I.B ﬁttings from the B.I.B. disconnects (QCD’s) and

re-connect the QCD ﬁttings to the appropriate B.I.B. container. (You will now begin the process of bringing syrup

back through the system)

a. Place empty tea dispenser under unit

b. Place empty brew basket into funnel rails

c. Push appropriate brew button for Sweet Tea (brew cycle will initiate)

d. Continue with brew cycle until syrup is ﬂowing freely from the dilution nozzle. You may need to repeat steps

“a” through “d” until syrup is dispensing from the dilution nozzle.

36748.3 111010

13

PROGRAMMING

Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various

brewing parameters such as brew temperatures, brew volumes, dilution volumes, pulse brew, etc. This allows

for the precise brewing of various ﬂavors of tea and coffee.

Programming of the brewer is achieved by entering a certain function. Then, by the use of hidden

programming switches and the brew/function switches, the operator can customize the brewing process to their

speciﬁcations.

PROGRAMMING SWITCHES

To access the programming mode, and to scroll through the different function screens, hidden programming

switches are used. There are ﬁve of these switches that will be used for the setup of the brewer.

a) Right Programming (hidden) switch (just to the right of the display): This is used to access the programming

mode, and is also used to scroll forward through the function list.

b) Left Programming (hidden) switch (just to the left of the display): This is used to scroll backwards through

the function list.

c) Brew A,B,C (Digital Brewer Control - Twins Only): Used to select options that appear on the display during

programming.

For more advanced PROGRAMMING information,

refer to programming manual at www.bunn.com

ITB

ITCB-DV & HV

36748.3 111010

ITCB-TWIN HV

HALF

FULL

BREW

A

BREW

B

BREW

C

®

ENABLE

ON / OFF

BREW

G

D

B

C

A

F

E

D

B

C

A

F

E

ENABLE

ON / OFF

ENABLE

ON / OFF

BREWBREW

®

c

a

B

14

MAIN SCREEN

PROGRAMMING THE BREWER

The programming of the brewer is divided into two levels. There is one function in Level 1. All other functions

are accessed in Level 2.

The following function screens are in order of appearance. Each screen will have instructions on how to

access and the procedures to program the various functions of the brewer.

IMPORTANT PROGRAMMING NOTES

- READ CAREFULLY -

To exit the programming mode at any time, press and release the ON/OFF pad located on the front switch

panel. The display will return to the MAIN SCREEN.

If none of the ﬁve programming switches are pressed within one minute during the setup of the brewer,

the programming of the function screen that is being set will be exited and the display will return to the MAIN

SCREEN.

Always remember to place a container and funnel under the sprayhead when operating the brewer during

the set-up of CALIBRATE FLOW, and testing the brew and dilution valves in SERVICE TOOLS/TEST OUTPUTS.

READY TO BREW

WATER TEMP: 205°

MEMORY

LOCK UNLOCK

PROGRAMMING

LOCKOUT SWITCH

This screen will be shown when the brewer is ready

for use. The screen displays the water temperature

in the tank. When the water in the tank reaches the

correct set temperature, the display will change from

HEATING to READY TO BREW.

PROGRAMMING LOCKOUT SWITCH

ITCB-located on the memory module board for early

models

located on the main control board for late models

ITB-located on the main control board

This switch can be set to prevent access to the

programming settings of the brewer. Once all the

correct brew settings are programmed, the operator

can set the switch to the "ON" position to prohibit

anyone from changing the settings. With the switch

in the "ON" position, the programming menus can still

be accessed to view the current settings. However, no

changes will be saved.

NOTE: ITB-Switches A,B & C are not used.

ITB ONLY

ITCB/HV

36748.3 111010

15

(-) DONE (+)

CALIBRATE FLOW?

NO YES

BREW COUNTERS?

NO YES

PROGRAMMING FUNCTIONS - LEVEL I

PROGRAMMING FUNCTIONS - FLOW CHART

PROGRAMMING FUNCTIONS - LEVEL 2

DILUTE OZ/M: XX.X

BREW LOCKOUT?

NO DONE YES

UNITS

METRIC DONE ENG

SET LANGUAGE?

NO YES

REVIEW RECIPES

NO YES

ASSIGN RECIPE

NO YES

MASTER TEMP 205°

(-) DONE (+)

READY DEGREE 5°

(-) DONE (+)

ENABLE ADS?

NO DONE YES

ENABLE SANITATION

NO DONE YES

ENABL ENERGYSAVR

NO DONE YES

ENABLE FRESH TIMER

NO DONE YES

XX REFILL XXX

(-) DONE (+)

NO YES

ENTER ASSET #

ENTER SERVICE #

NO YES

SERVICE TOOLS

NO YES

FACTORY DEFAULTS

NO YES

ITB

SPRAY OZ/M: XX.X

(-) DONE (+)

36748.3 111010

For more advanced PROGRAMMING information,

refer to programming manual at www.bunn.com

16

SPRAY OZ/M: XX.X

(-) DONE (+) (-) DONE (+)

CALIBRATE FLOW?

NO YES

BREW COUNTERS?

NO YES

PROGRAMMING FUNCTIONS - LEVEL I

PROGRAMMING FUNCTIONS - FLOW CHART

PROGRAMMING FUNCTIONS - LEVEL 2

DILUTE OZ/M: XX.X

SET RECIPES TEMPS

NO YES

BREW LOCKOUT?

NO DONE YES

UNITS

METRIC DONE ENG

SET LANGUAGE?

NO YES

REVIEW RECIPES

NO YES

ASSIGN RECIPE

NO YES

MASTER TEMP 205°

(-) DONE (+)

READY DEGREE 5°

(-) DONE (+)

ENABLE ADS?

NO DONE YES

SET NEW RECIPE?

NO YES

ENABLE SANITATION

NO DONE YES

ENABL ENERGYSAVR

NO DONE YES

ENABLE FRESH TIMER

NO DONE YES

XX REFILL XXX

(-) DONE (+)

NO YES

ENTER ASSET #

ENTER SERVICE #

NO YES

SERVICE TOOLS

NO YES

FACTORY DEFAULTS

NO YES

ITCB

36748.3 111010

17

PROGRAMMING FUNCTIONS - LEVEL I

PROGRAMMING FUNCTIONS - FLOW CHART

PROGRAMMING FUNCTIONS - LEVEL 2

BREW LOCKOUT ?

NO DONE YES

UNITS

METRIC DONE ENG

SET LANGUAGE ?

NO YES

REVIEW RECIPES ?

NO YES

ASSIGN RECIPE ?

NO YES

SET TEMP 200°

(-) DONE (+)

READY DEGREE 5°

(-) DONE (+)

ENABLE ADS ?

NO DONE YES

SET NEW RECIPE ?

NO YES

ENABLE SANITATION

NO DONE YES

Enabl EnergySavr

NO DONE YES

ENABLE FRESH TIMER

NO DONE YES

XX REFILL XXX

(-) DONE (+)

ITCB-DV HV

36748.3 111010

FACTORY DEFAULTS

NO YES

SERVICE TOOLS ?

NO YES

BREW ALERT ?

NO YES

SPRAY OZ/M: XX.X

(-) DONE (+)

BREW COUNTERS ?

NO YES

ENTER ASSET # ?

ENTER SERVICE # ?

NO YES

FUNNEL DETECT ?

NO YES

(-) DONE (+)

BYPASS OZ/M: XX.X

(-) DONE (+)

CALIBRATE FLOW ?

NO YES

DILUTE OZ/M: XX.X

18

L SPRY OZ/M: XX.X

(-) DONE (+) (-) DONE (+)

L BYPS OZ/M: XX.X

BREW LOCKOUT ?

NO DONE YES

UNITS

METRIC DONE ENG

SET LANGUAGE ?

NO YES

REVIEW RECIPES ?

NO YES

ASSIGN RECIPE ?

NO YES

SET TEMP 200°

(-) DONE (+)

READY DEGREE 5°

(-) DONE (+)

ENABLE ADS ?

NO DONE YES

SET NEW RECIPE ?

NO YES

ENABLE SANITATION

NO DONE YES

Enabl EnergySavr

NO DONE YES

ENABLE FRESH TIMER

NO DONE YES

XX REFILL XXX

(-) DONE (+)

R SPRY OZ/M: XX.X

(-) DONE (+) (-) DONE (+)

R BYPS OZ/M: XX.X

NO YES

ENTER ASSET # ?

ENTER SERVICE # ?

NO YES

36748.3 111010

PROGRAMMING FUNCTIONS - LEVEL I

PROGRAMMING FUNCTIONS - FLOW CHART

PROGRAMMING FUNCTIONS - LEVEL 2

ITCB HV TWIN

CALIBRATE FLOW ?

NO YES

BREW COUNTERS ?

NO YES

SERVICE TOOLS ?

NO YES

FACTORY DEFAULTS

NO YES

(-) DONE (+)

L Dilut OZ/M: XX.X

(-) DONE (+)

R Dilut OZ/M: XX.X

FUNNEL DETECT ?

NO YES

BREW ALERT ?

NO YES

18

L SPRY OZ/M: XX.X

(-) DONE (+) (-) DONE (+)

L BYPS OZ/M: XX.X

BREW LOCKOUT ?

NO DONE YES

UNITS

METRIC DONE ENG

SET LANGUAGE ?

NO YES

REVIEW RECIPES ?

NO YES

ASSIGN RECIPE ?

NO YES

SET TEMP 200°

(-) DONE (+)

READY DEGREE 5°

(-) DONE (+)

ENABLE ADS ?

NO DONE YES

SET NEW RECIPE ?

NO YES

ENABLE SANITATION

NO DONE YES

Enabl EnergySavr

NO DONE YES

ENABLE FRESH TIMER

NO DONE YES

XX REFILL XXX

(-) DONE (+)

R SPRY OZ/M: XX.X

(-) DONE (+) (-) DONE (+)

R BYPS OZ/M: XX.X

NO YES

ENTER ASSET # ?

ENTER SERVICE # ?

NO YES

36748.3 111010

PROGRAMMATION - NIVEAU I

PROGRAMMATION – DIAGRAMME DE CIRCULATION

PROGRAMMATION - NIVEAU 2

ITCB HV TWIN

CALIBRATE FLOW ?

NO YES

BREW COUNTERS ?

NO YES

SERVICE TOOLS ?

NO YES

FACTORY DEFAULTS

NO YES

(-) DONE (+)

L Dilut OZ/M: XX.X

(-) DONE (+)

R Dilut OZ/M: XX.X

FUNNEL DETECT ?

NO YES

BREW ALERT ?

NO YES

VERROUILLAGE D’INFUSION?

NON TERMINÉ OUI

RÉGLER LANGUE?

NON OUI

RÉGLER NOUVELLE RECETTE?

NON OUI

ACTIVER DÉSINFECTION

NON TERMINÉ OUI

PULVÉRISER G OZ/M

(-) TERMINÉ (+)

OUTILS

NON OUI

DILUTION G OZ/MIN

(-) TERMINÉ (+)

ENTRER N

O

D’INVENTAIRE

NON OUI

UNITÉ DE MESURE

MÉTRIQUE TERMINÉ ANG

REVOIR RECETTES

NON OUI

ASSIGNER RECETTE

NON OUI

TEMP PRIORITAIRE 200°

(-) TERMINÉ (+)

TEMP PRÉDÉTERMINÉE 5°

(-) TERMINÉ (+)

ACTIVER PUBLICITÉ?

NON TERMINÉ OUI

ACTIVER ÉCONOMISEUR D’ÉNERGIE

NON TERMINÉ OUI

ACTIVER MINUT CAFÉ FRAIS

NON TERMINÉ OUI

XX REMPLISSAGE XXX

(-) TERMINÉ (+)

PULVÉRISER D OZ/M

(-) TERMINÉ (+)

DÉRIVATION G OZ/M : XX.X

(-) TERMINÉ (+)

DÉRIVATION D OZ/M : XX.X

(-) TERMINÉ (+)

DILUTION D OZ/MIN

(-) TERMINÉ (+)

CALIBRER DÉBIT?

NON OUI

COMPTEUR D’INFUSION?

NON OUI

ENTRER NO DE CENTRE DE SERVICE

NON OUI

DÉTECTION D’ENTONNOIR?

NON OUI

ALARME D’INFUSION?

NON OUI

RÉGLAGES EN USINE

NON OUI

17

PROGRAMMATION - NIVEAU I

PROGRAMMATION – DIAGRAMME DE CIRCULATION

PROGRAMMATION - NIVEAU 2

BREW LOCKOUT ?

NO DONE YES

UNITS

METRIC DONE ENG

SET LANGUAGE ?

NO YES

REVIEW RECIPES ?

NO YES

ASSIGN RECIPE ?

NO YES

SET TEMP 200°

(-) DONE (+)

READY DEGREE 5°

(-) DONE (+)

ENABLE ADS ?

NO DONE YES

SET NEW RECIPE ?

NO YES

ENABLE SANITATION

NO DONE YES

Enabl EnergySavr

NO DONE YES

ENABLE FRESH TIMER

NO DONE YES

XX REFILL XXX

(-) DONE (+)

ITCB-DV HV

36748.3 111010

FACTORY DEFAULTS

NO YES

SERVICE TOOLS ?

NO YES

BREW ALERT ?

NO YES

SPRAY OZ/M: XX.X

(-) DONE (+)

BREW COUNTERS ?

NO YES NO YES

ENTER ASSET # ?

ENTER SERVICE # ?

NO YES

FUNNEL DETECT ?

NO YES

(-) DONE (+)

BYPASS OZ/M: XX.X

(-) DONE (+)

CALIBRATE FLOW ?

NO YES

DILUTE OZ/M: XX.X

RÉGLER LANGUE?

NON OUI

UNITÉ DE MESURE

MÉTRIQUE TERMINÉ ANG

REVOIR RECETTES

NON OUI

ASSIGNER RECETTE

NON OUI

RÉGLER NOUVELLE RECETTE?

NON OUI

TEMP PRIORITAIRE 200°

(-) TERMINÉ (+)

TEMP PRÉDÉTERMINÉE 5°

(-) TERMINÉ (+)

ACTIVER PUBLICITÉ?

NON TERMINÉ OUI

ACTIVER DÉSINFECTION

NON TERMINÉ OUI

ACTIVER ÉCONOMISEUR D’ÉNERGIE

NON TERMINÉ OUI

ACTIVER MINUT CAFÉ FRAIS

NON TERMINÉ OUI

XX REMPLISSAGE XXX

(-) TERMINÉ (+)

PULVÉRISER OZ/M

(-) TERMINÉ (+)

DÉRIVATION OZ/M : XX.X

(-) TERMINÉ (+)

DILUTION OZ/MIN

(-) TERMINÉ (+)

CALIBRER DÉBIT?

NON OUI

COMPTEUR D’INFUSION?

NON OUI

ENTRER N

O

D’INVENTAIRE

NON OUI

ENTRER N

O

DE CENTRE DE SERVICE

NON OU

DÉTECTION D’ENTONNOIR?

NON OUI

ALARME D’INFUSION?

NON OUI

OUTILS

NON OUI

RÉGLAGES EN USINE

NON OUI

VERROUILLAGE D’INFUSION?

NON TERMINÉ OUI

La page charge ...

Bunn ITB-DBC Le manuel du propriétaire

Bunn ITB-DBC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents