Xantrex Technologies 1800 Manuel utilisateur

Marque: Xantrex Technologies

Modèle: 1800

Taper: Manuel utilisateur

1000

1000i

1800

1800i

Owner’s Manual

Xantrex Prosine

Sine Wave Inverter

1000/1800

English

Xantrex Prosine Inverter Owner’s Manual

Table of Contents

Important Safety Instructions .......................................................................................................................................................................................... 1

1. Introduction ................................................................................................................................................................................................................ 3

1.1 Prosine Inverter Key Features .......................................................................................................................................................................... 3

2. Installation .................................................................................................................................................................................................................. 4

2.1 Requirements for Installation ............................................................................................................................................................................ 4

2.2 Locating the Prosine Inverter ............................................................................................................................................................................ 4

2.3 Mounting the Prosine Inverter........................................................................................................................................................................... 4

2.4 Wiring the Prosine Inverter ............................................................................................................................................................................... 5

2.4.1 Input and Output Protection ..............................................................................................................................................................................................5

2.4.2 Making AC Wiring Connections ........................................................................................................................................................................................6

2.4.3 Ground Fault Circuit Interrupters (GFCIs) ........................................................................................................................................................................7

2.4.4 Making DC Wiring Connections ........................................................................................................................................................................................7

3. Prosine Inverter Operation ......................................................................................................................................................................................... 9

3.1 Principles of Operation...................................................................................................................................................................................... 9

3.2 Output Waveform ............................................................................................................................................................................................. 9

3.3 Control Panel ...................................................................................................................................................................................................10

3.4 Prosine POWERSAVE Mode ...........................................................................................................................................................................10

3.5 Inverter Operating Limits and Protection Features ..........................................................................................................................................11

4. Testing........................................................................................................................................................................................................................11

5. Troubleshooting Guide ..............................................................................................................................................................................................12

5.1 Fault Conditions and Indicators........................................................................................................................................................................12

6. Warranty ...................................................................................................................................................................................................................13

7. Appendices................................................................................................................................................................................................................14

7.1 Battery Type ......................................................................................................................................................................................................14

7.2 Battery Size......................................................................................................................................................................................................15

8. Performance Graphs.................................................................................................................................................................................................16

8.1 Power Derating Curve.......................................................................................................................................................................................16

8.2 Efficiency Curve...............................................................................................................................................................................................17

9. Specifications ............................................................................................................................................................................................................18

English

SUPERIOR, PACER are registered trademarks of TROJAN BATTERY Company

SEAVOLT, SEAGEL are registered trademarks of WEST MARINE PRODUCTS

VOYAGER is a registered trademark of DELCO-REMY

GENESIS is a registered trademark of GATES ENERGY PRODUCTS (HAWKER ENERGY)

EVOLYTE is a registered trademark of GNB INDUSTRIAL BATTERY CO.

PREVAILER is a registered trademark of SONNENSCHEIN

Xantrex Prosine Inverter Owner’s Manual

Trademarks

Xantrex, Prosine, and Smart Choice For Power are trademarks of Schneider Electric Services International sprl, registered

in the U.S. and other countries.

Other trademarks, registered trademarks, and product names are the property of their respective owners and are used

herein for identification purposes only.

Notice of Copyright

Xantrex Prosine Sine Wave Inverter 1000, 1000i/1800, 1800i Owner’s Manual © January 2009, 2005-2008 Xantrex

without the express written consent of: Xantrex Technology Inc., 161-G South Vasco Road, Livermore, California USA

94551.

Xantrex Technology Inc. reserves the right to revise this document and to periodically make changes to the content hereof

without obligation or organization of such revisions or changes unless required to do so by prior arrangement.

Exclusion for Documentation

UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC., (“XANTREX TECHNOLOGY”)

(A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED

IN ITS MANUALS OR OTHER DOCUMENTATION.

(B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT,

CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH

INFORMATION WILL BE ENTIRELY AT THE USER’S RISK; AND

THE ACCURACY OF THE TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED. APPROVED CONTENT IS CONTAINED WITH THE

ENGLISH LANGUAGE VERSION WHICH IS POSTED AT WWW.XANTREX.COM.

Date and Revision

January 2009, Revision B

Part Number

445-0049-01-01

Contact Information

Web: www.xantrex.com

Email: [email protected]

Phone: 1-800-670-0707 (in North America), 1-408-987-6030 (direct)

Fax: 1-800-994-7828 (in North America), 1-604-422-2756 (direct)

English 1

Important Safety Instructions

General Safety Precautions

1. SAVE THESE INSTRUCTIONS. This OWNER’S

MANUAL contains important safety and operating

information for the Prosine Inverter.

2. Do not expose the Prosine Inverter to rain, snow,

spray, bilge or dust. To reduce risk of fire hazard,

do not cover or obstruct the ventilation openings.

Do not install the Prosine Inverter in a zero-

clearance compartment. Overheating may result.

3. Do not use attachments not recommended or sold

by Xantrex. Doing so may result in a risk of fire,

electric shock, or injury to persons.

4. The Prosine Inverter is designed to be permanently

connected to your DC electrical systems (and for

hardwire versions, permanently connected to your

AC electrical system). To ensure adherence to

proper electrical wiring regulations all wiring must

be done by a certified technician or electrician.

5. To avoid a risk of fire and electric shock, make

sure that existing wiring is in good electrical

condition; and that wire size is not undersized. Do

not operate the Prosine Inverter with damaged or

substandard wiring.

6. Do not operate the Prosine Inverter if it has received

a sharp blow, been dropped, or otherwise damaged

in any way. If the Prosine Inverter has been

damaged, refer to Section 6 of this manual.

7. Do not disassemble the Prosine Inverter; refer to

Section 6 of this manual for instructions on

obtaining service for the Prosine Inverter.

Attempting to service the unit yourself may result

in a risk of electrical shock or fire.

8. To reduce risk of electrical shock, disconnect the

DC power (and AC power if applicable on hardwire

versions) from the Prosine Inverter before

attempting any maintenance or cleaning or working

on any equipment and circuits connected to the

Prosine Inverter. Turning off controls will not reduce

this risk.

9. Grounding: The Prosine Inverter must be provided

with an equipment-grounding conductor connected

to the AC input ground terminal. Grounding and

all other wiring must comply with local codes and

ordinances.

10. For marine applications, special installation codes

may apply. For example, in the U.S., the installation

shall comply with the United States Coast Guard

Electrical Regulations (33CFR183, Sub part 1).

Explosive Gas Precautions

1. This equipment contains components which can

produce arcs or sparks. To prevent fire or explosion

do not install in compartments containing batteries

or flammable materials or in locations which require

ignition protected equipment.This includes any

space containing gasoline-powered machinery, fuel

tanks, or joints, fittings, or other connection between

components of the fuel system.

2. Working in the vicinity of a lead-acid battery is

dangerous. Batteries generate explosive gases

during normal battery operation.

3. To reduce the risk of battery explosion, follow these

instructions and those published by the battery

manufacturer and the manufacturer of the

equipment in which the battery is installed.

Precautions When Working With

Batteries

1. Someone should be within range of your voice or

close enough to come to your aid when you work

near a lead-acid battery.

2. Have plenty of fresh water and soap nearby in case

battery acid contacts skin, clothing, or eyes.

3. Wear complete eye protection and clothing

protection. Avoid touching eyes while working near

batteries.

4. Clean battery terminals before making connections.

Wear eye protection to keep corrosion from coming

in contact with eyes.

5. If battery acid contacts skin or clothing, wash

immediately with soap and water. If acid enters eye,

immediately flood eye with running cold water for

at least 20 minutes and get medical attention

immediately.

6. NEVER smoke or allow a spark or flame in vicinity

of battery or engine.

7. Do not drop a metal tool on the battery. The resulting

spark or short-circuit on the battery or other

electrical part may cause an explosion.

8. Remove personal metal items such as rings,

bracelets, necklaces, and watches when working

with a lead-acid battery. A lead-acid battery

produces a short-circuit current high enough to weld

a ring or the like to metal, causing a severe burn.

WARNING

Before you install and use your Prosine

Inverter, be sure to read and save these safety

instructions.

Xantrex Prosine Inverter Owner’s Manual

2 English Xantrex Prosine Inverter Owner’s Manual

English 3

1. Introduction

Thank you for your purchase of this Prosine Sine

Wave Inverter. As a high quality, true sine wave output

inverter, you can expect exceptional performance and

years of dependable operation. The true sine wave AC

output from the inverter ensures all AC loads operating

from the unit perform efficiently and correctly. Since

these loads were designed to operate from true sine wave

voltage, you can expect these loads to operate the same

as if operating from grid/utility supplied power. In some

cases, the true sine wave output from the Xantrex inverter

is even superior to the power supplied by your utility

company.

To get the most out of your Prosine Inverter, carefully

read and follow the instructions in this guide. Pay special

attention to the Important Safety Instructions and to the

CAUTION and WARNING statements found

throughout the manual and on the product. Please retain

all packaging.

Should you have any questions before, during, or after

installation, please contact Xantrex.

Phone: 1-800-670-0707, 1-408-987-6030 (direct)

Fax: 1-800-994-7828, 1-604-422-2756 (direct)

Email: [email protected]

Web: www.xantrex.com

1.1 Prosine Inverter Key Features

The Prosine Inverter utilizes advanced high frequency

switching technology in the power conversion process.

The circuits are similar to those used in power supplies

for computers and other electronic equipment. This

technology offers several benefits:

•Light weight: for easy installation

•Totally silent: for quiet operation

•High surge capability: for “hard-to-start” AC loads

See Section 10 (Specifications) for complete product

specifications.

1.1.1 Inverter Function

When connected properly and the power switch is turned

to the (I) position, the inverter draws power from a battery

and delivers a true sine wave AC output voltage. If the

battery voltage is within the operating range of the unit,

the inverter will continue to deliver AC power to the

loads connected. High and low battery shutdowns will

engage if the battery voltage falls out of the specified

range of operation (10–16 VDC on 12 V models, 20–32

VDC on 24 V models).

1.1.2 Control Panel

The Control Panel displays operating information so you

can monitor the status of the Inverter and your batteries.

This panel can be removed and re-attached in different

orientations so the information is directed at you in the

most convenient fashion, for all recommended mounting

configurations. With the optional Interface Panel, the

display can be fully removed from the base chassis and

remotely located in the place of your choice (e.g. on the

dash of your vehicle).

1.1.3 Automatic Transfer Switch

Your Prosine Inverter may be equipped with a transfer

relay if specified prior to purchase. The transfer relay serves

two purposes: 1) allows the AC output of the inverter to

be wired into an existing AC system as a source of power

and 2) allows the Prosine Inverter to automatically

become the source of power should your utility source

fail.

When utility AC power fails, the transfer relay is de-

energized and the load is automatically transferred to the

inverter output within 20–30 milliseconds. With the

POWERSAVE feature enabled (recommended for

reducing standby power consumption), AC output from

the inverter may be delayed for up to 2½ seconds. Once

AC utility is restored, the relay energizes and the load is

automatically reconnected to AC utility.

Identifying Models With Transfer Switches

1) Check the UPC code on the product box. Units with

transfer switches have UPC codes that end with these five

digits:

2) If there is an AC outlet on the front of the unit, it is

not equipped with an internal transfer switch.

3) For Prosine Inverters with hardwire connections, you

can identify whether your unit has an internal transfer

switch by removing the cover on the AC wiring

compartment and checking the label above the terminal

block inside.

If your unit has a label similar to one of these two

labels, it has an internal transfer switch:

Units with this label do not have an internal transfer

switch:

i0001/0001ledoMi0081/0081ledoM

4801648816

4701647816

2501625816

8001680816

2001620816

WARNING

Note that in (##

#) (Bypass) position the front panel

switch does NOT turn off all voltages inside the

unit. This control only deactivates the AC

conversion circuitry. On AC hardwire/transfer re-

lay versions any utility voltage present on the AC

input terminals will be present on the AC output

terminals.

Please record the following information if you need

to contact Xantrex for servicing of the unit.

Serial No.: ___________________________

Place of purchase: ___________________________

Date of purchase: ___________________________

Xantrex Prosine Inverter Owner’s Manual

4 English Xantrex Prosine Inverter Owner’s Manual

2. Installation

This section contains instructions for installing the

Xantrex Prosine Inverter. After securing the unit and

making wiring connections, do not turn the unit on.

Proceed to the next section of the manual which provides

operating instructions.

2.1 Requirements for Installation

Installation Regulations: Depending on the type of

location in which you are installing the Prosine Inverter,

there are different codes and regulations that the

installation must meet such as your national and local

electrical codes for residential installations. Other examples

of codes and regulations for North American installations

include:

•US Coast Guard and ABYC requirements for

installations on marine vessels

•RV Industry Association (RVIA), CSA, and UL

requirements for installations in recreational vehicles.

It is the installer´s responsibility to ensure that all

applicable installation requirements are met.

What You Need to Install the Prosine Inverter

You need the following tools and hardware to properly

install the inverter:

•wire stripper

•mounting screws/bolts (¼” or 6mm diameter screws)

•small flat blade screwdriver (for hardwire versions)

•small Phillips screwdriver

•wrench for DC terminals (½” or 13mm)

•AC wiring for hardwire configured models (see AC

wiring section for details)

•DC cables (see DC wiring section for details)

•Wire connectors and crimp tool for your DC cables

•AC and DC disconnects and over-current protective

devices (see section 2.4.1 for details)

2.2 Locating the Prosine Inverter

The inverter utilizes complex electronic circuits, and

although design precautions have been made for protection

of these circuits, they can be susceptible to damage from

use in extreme environments. The Prosine Inverter should

only be installed in a location that meets the following

requirements:

• Dry:do not allow water or other fluids to drip or splash

on the Prosine Inverter. Do not mount the inverter in an

area subject to splashing or dripping water or bilge.

• Cool: normal ambient air temperature should be between

0°C (32°F) and 25°C (77°F)—the cooler the better within

this range. Refer to the operating temperature information

in section 9 (specifications) for more details.

• Ventilated: allow at least 5 inches (13 cm) of clearance

all around the unit. Ensure the ventilation openings on the

unit are not obstructed. If mounting in a compartment,

ventilate with louvers or cut-outs.

• Safe: do not install the Prosine Inverter in the same

compartment as batteries or in any compartment capable

of storing flammable liquids such as gasoline. Do not

install the inverter in an engine compartment or other

location where ignition protected equipment is required.

• Dust-free: do not install the Prosine Inverter in a dusty

environment where either dust, wood particles or other

filings/shavings are present. These can be pulled into the

unit when the cooling fan is operating.

• Close to AC junction box: avoid the use of extended

wire lengths if possible.

• Close to battery/batteries: Avoid excessive cable

lengths but do not install the Prosine Inverter in the same

compartment as batteries. Use the recommended wire

lengths and sizes (see section 2.4.4). Also do not mount

the inverter where it will be exposed to the gases

produced by the battery. These gases are very corrosive

and prolonged exposure will damage the inverter.

• Protected from battery acid: never allow battery acid

to drip on the Prosine Inverter or its wiring when reading

specific gravity or filling the battery.

2.3 Mounting the Prosine Inverter

Before mounting the Prosine Inverter, test the chosen

location for adequate space around the unit to allow for

connections and ventilation. Mounting hardware should

be corrosion resistant and ¼” or 6mm diameter screws.

Your mounting system should be able to support three

times the weight of the inverter, which weighs

approximately 16 lbs (7.3Kg). The more clearance for

ventilation around the unit, the better the performance.

At a minimum, have 5” of free space on all sides of the

inverter.

To mount the Prosine Inverter

1. Mount the Prosine Inverter on either a horizontal or

vertical surface (such as a bulkhead) using the

mounting holes provided. For secure, permanent

mounting, use all eight mounting holes. To meet

regulatory requirements, the inverter must be

mounted in one of the three orientations shown.

CAUTION

The Pro sine Inverter is designed to be

permanently connected to your DC electrical

system. When Configured as an AC hardwire

version, the inverter is also designed to be

permanently connected to your AC electrical

system. To ensure adherence to proper electrical

wiring regulations, all wiring must be done by a

certified technician or electrician.

WARNING

Review the Important Safety Instructions found

at the beginning of this manual and read this

entire section, paying particular attention to the

CAUTION and WARNING statements, before

proceeding with the installation.

Figure 1. Approved orientations for

inverter mounting

English 5

2. Remove and re-attach the front panel depending on

the orientation of the base unit itself. For example, if

the unit is mounted on a vertical surface, you may

want to remove the panel and attach it so it is again

readable horizontally. This can be done by removing

the four screws, taking the panel out of the housing,

rotating the panel and reattaching the panel to the

base unit. Be sure to re-install all four screws.

3. The front panel can also be remotely located away

from the base chassis. Simply remove the panel

from the face of the unit, install the interface panel

option (purchased separately) and connect the 30

ft. (9 m) extension cord. The cord can then be run to

the location where the panel is to be mounted, and

attached to the panel. The unit can now be controlled

and monitored from the location of your choice. Do

not remotely mount the display panel without

purchasing the Interface Panel option and properly

installing this panel on the inverter. The Interface

Panel significantly reduces radiated interference

generated along the length of the cable, decreasing

the chance of resulting interference with other

equipment.

2.4 Wiring the Prosine Inverter

For units equipped with an AC outlet:

If your Prosine Inverter is equipped with an AC outlet

on the front, then you will be mainly interested in the

DC wiring instructions that follow (section 2.4.4). Once

your DC connections and ground wiring connection are

complete, the unit is ready to deliver AC power.

For AC hardwire versions:

If your unit is equipped with an AC hardwire terminal

strip, (with or without transfer relay) then the following

AC wiring instructions are important for you to read

through. When hardwire configured, the inverter

manages all AC power and therefore must be wired in

between any utility connection and distribution panel.

As a starting point for the wiring instructions, here is a

brief summary of the wiring sequence for hardwire

configured inverters. Please thoroughly read the

remainder of the wiring instructions (section 2.4.2)

which details each wiring step and follows the Input

and Output Protection section:

1. Ensure the (##

#/I) control panel switch is in the (##

position. For those hardwire equipped models with

a transfer relay, connected AC source (INPUT)

power will be passed through the inverter making

the output terminal and connected wiring live. This

is the case even with the control panel switch in

the (##

#) position so ensure all power is disconnected

at its source.

2. Connect AC input wiring, AC output wiring, Chassis

Ground, DC positive cable and finally, DC negative

cable in that order.

3. Connect each circuit to its source.

2.4.1 Input and Output Protection

In order to meet CSA, UL, and electrical code

requirements, the AC and DC inputs and outputs of the

Prosine Inverter must be provided with overcurrent

protection such as a circuit breaker or fuse, and with a

disconnect device, as follows: (note the “AC Input” and

“AC Output” information below only applies to units

equipped with AC hardwire terminal strips, not AC

output receptacle equipped versions).

DC Input: Protection for the DC wiring (an inline fuse

/circuit breaker) is needed as close as possible to the

battery to protect the wiring from your batteries to the

Prosine Inverter. The current rating of this DC fuse or

circuit breaker must be large enough to allow the inverter

to operate your loads, but if the rating is too high,

electrical codes will require you to use larger DC cables

than you would otherwise have to. The fuse or circuit

breaker must be rated and approved for use on minimum

12V or 24V DC circuits as applicable by the model of

your inverter. Fuses or circuit breakers rated only for

AC service are not suitable for use on DC circuits and

may pose a hazard. The wire size used between the

Prosine Inverter and the fuse or circuit breaker must be

sized to match the fuse or circuit breaker´s current rating,

in accordance with the electrical codes or regulations

applicable to your installation (see Table 4).

AC Input: The installation must provide over-current

protection for the AC input circuit. The circuit breaker

or fuse used must be rated and approved for use on

120VAC branch circuits for 120V models and for

230VAC branch circuits for 230V models. The wire

size used between the breaker and the Prosine Inverter

input must be sized to match the circuit breaker, in

accordance with the electrical codes or regulations

applicable to your installation. Refer to Table 1 for

sizing information.

WARNING

Fire and shock hazard. Make sure wiring is

disconnected from all electrical sources

before handling. All wiring must be done in

accordance with local and national electrical

wiring regulations by a certified electrician or

technician.

Figure 2. Control panel attachment

Xantrex Prosine Inverter Owner’s Manual

6 English

AC Output: The circuit breaker or fuse used must be

rated and approved for use on 120V AC branch circuits

for 120V models and for 230VAC branch circuits for

230V models. The wire size used between the Prosine

Inverter output and the breaker, and between the breaker

and your loads, must be sized to match the circuit

breaker’s rating, in accordance with the electrical codes

or regulations applicable to your installation. Refer to

Table 1 for sizing information.

Disconnect devices: Since circuit breakers can be

turned off and fuses can be removed from the circuit,

either type of device will also meet the requirement for

a disconnect device in each of the above circuits. Note

that the required disconnect device is not intended for

disconnection under load, it is only meant to be a way

to isolate the Prosine Inverter from the input and output

power sources.

2.4.2 Making AC Wiring Connections

Again, this section applies to those models configured

with an AC hardwire terminal strip. As mentioned

previously, your AC wiring must be sized to match the

current rating of the AC breakers you provide on the

input and output AC circuits in accordance with the

electrical codes or regulations applicable to your

installation. Table 1 is based on the U.S. National

Electrical Code (1999), the Canadian Electrical Code

(1998), and European wiring practices (for 230V

models). There may be other codes and regulations

applicable to your installation.

Note that there is no difference between the

recommendations for the 1000 and 1800 models. This

is because the bypass rating of these products is the

same (i.e. 15A for 1000 and 1800 and 10A for 1000i

and 1800i).

Figure 3 may be a useful reference as it illustrates the

AC wiring connection terminals for Prosine Inverter

models that are AC hardwire configured.

AC Wiring should be connected in the following order:

1. AC INPUT (source)

2. AC OUTPUT (load)

To make AC wiring connections:

1. The AC wiring compartment is located on the right-

hand side of the Prosine Inverter when looking at

the front of the unit. Remove the AC wiring

compartment cover to gain access to the AC terminal

strip inside.

2. Remove the knockouts from the cover of the wiring

compartment to create holes for your cable clamps

(see Figure 3).

3. Run the three conductor AC INPUT (source) wiring

through a cable clamp and into the wiring

compartment, via the knockout on the right side of

the front panel. Connect the AC INPUT ground wire

first to the ground terminal (ground symbol with

circle around it), and then connect the AC INPUT

line and neutral wires to the corresponding Prosine

Inverter AC input terminals. Refer to Table 2 for

typical colour coding and terminal identification.

4. In a similar manner, connect the AC OUTPUT

(load) wiring to the Prosine Inverter AC output

terminals (connect the output ground to the ground

terminal identified by the symbol with no circle

around it). Terminal to wiring connections should

be done as shown in Table 2.

5. After wiring, double check and review all

connections to make sure the wires are in the correct

terminals and the terminals are tight (the

recommended torque is 7.5 in-lbs., 9.8 Nm).

Table 1. Circuit Breakers and Wire Sizing

Figure 3. AC wiring terminals (hardwire versions only)

WARNING

Shock Hazard. Before proceeding further,

ensure that the Prosine Inverter is NOT

connected to any batteries, and that all wiring

is disconnected from any electrical sources.

Do not connect the output terminals of the

inverter to an incoming AC source.

LEDOM TUPTUOCAdnaTUPNICA

deriuqeR gnitaRrekaerB deriuqeR eziSeriW

V42/21-0001 V42/21-0081 .xamA02GWA21

V42/21-i

0001 V42/21-i0081 .xamA01mm5.2-0.1

Table 2. AC Terminal and Wiring

Identification

LANIMRET

ROLOCERIWCA

CAV021

)naciremA.N(

CAV032

)naeporuE(

)L(ENILkcalBnworB

)N(LARTUENetihWeulB

DNUORG roneerG reppocerab rowolleY/neerG reppocerab

Xantrex Prosine Inverter Owner’s Manual

English 7

AC Safety Grounding: During the AC wiring

installation, AC input and output ground wires are

connected to the inverter. The AC input ground wire

must connect to the incoming ground from your AC

utility source. The AC output ground wire should go to

the grounding point for your loads (e.g. a distribution

panel ground bus).

Neutral Grounding:

a) 120V models: The neutral conductor of the AC

output circuit of the Prosine Inverter is

automatically connected to the safety ground during

inverter operation. This conforms to National

Electrical Code requirements that separately

derived AC sources (such as inverters and

generators) have their neutral conductors tied to

ground in the same way that the neutral conductor

from the utility is tied to ground at the AC breaker

panel. For models configured with a transfer relay,

when AC utility power is present and the Prosine

Inverter is in bypass mode, this connection (neutral

of the inverter‘s AC output to input safety ground)

is not present so that the utility neutral is only

connected to ground at your breaker panel, as

required.

b) 230V models: There is no connection made inside

the Prosine Inverter from either of the line

conductors (line or neutral) to the safety ground.

2.4.3 Ground Fault Circuit Interrupters

(GFCIs)

Installations in Recreational Vehicles (for North

American approvals) will require GFCI protection of

all branch circuits connected to the AC output of the

hardwire terminal equipped Prosine Inverters. In

addition, electrical codes require GFCI protection of

certain receptacles in residential installations. While

the true sine wave output of the Prosine Inverter is

equivalent to the waveform provided by utilities,

compliance with UL standards requires us to test and

recommend specific GFCIs.

surge capability and frequent low input voltage

warnings and shutdowns.

These low input voltage warnings are due to DC voltage

drop across the cables from the inverter to the batteries.

The longer and narrower these cables, the greater the

voltage drop. Table 3 shows voltage drop per foot of

cable, at various power output levels.

For example, if the 1800 Inverter is 10 ft. from your

battery, is operating at 2000 watts, and is improperly

connected with #4AWG wire, then you can expect a

voltage drop per foot of 0.0506 V. Total cable length is

actually 20 ft., not 10 ft., since the cable length is

measured from the battery to the inverter and back.

Therefore, multiply 0.0506 V by 20 to get a total voltage

drop of 1.012 V. If your battery voltage is only 11.2 VDC,

then the actual voltage at the inverter is 10.188 (11.2

V–1.012 V) because of this significant voltage drop.

The Prosine Inverter will either be in low input voltage

warning or shutdown in such a condition. In high current

draw and surge situations, the unit may go into low

input voltage shutdown if the cables are too small and

too long.

Increasing your DC cable size will help improve the

situation. With cables sized correctly, and using a #0

AWG cable, your voltage drop will be 0.02 VDC

(multiplied by 20, you get a total voltage drop of 0.4 VDC).

This illustrates that at 10 ft. away from the battery and

with large cables, you can expect voltage drop. Again,

try to keep cable length to a minimum and use the

maximum gauge cable possible. Xantrex recommends

the following cables for optimum inverter performance

(apply to both 120 V and 230 V versions).

1000/12: #0 AWG or 55 mm2

1000/24: #6 AWG or 13 mm2

1800/12: #4/0 AWG or 110 mm2

1800/24: #2 AWG or 34 mm2

Also, use only high quality copper wiring and keep cable

length short, a maximum of 3–6 ft.

Xantrex has tested the following GFCI-protected 15 A

receptacles and found that they functioned properly

when connected to the AC output of the inverter:

2.4.4 Making DC Wiring Connections

Follow this procedure to connect the battery cables to

the DC input terminals on the Prosine Inverter. Your

cables should be as short as possible (ideally, less than

10 ft./3 m) and large enough to handle the required

current, in accordance with the electrical codes or

regulations applicable to your installation. Cables that

are not an adequate gauge (too narrow) or are too long

will cause decreased inverter performance such as poor

Xantrex Prosine Inverter Owner’s Manual

RxI=V ecnatsiseRxtnerruC=egatloV

retrevnI )W(tuptuO 00500010051000200520003

)A(tnerruC05001051002052003

eriW eguaG )GWA(

ecnatsiseR )tf/smho( C°52@

egatloV porD .tfrep

egatloV po

rD .tfrep

egatloV porD .tfrep

0/4050000.05200.00500.05700.00010.05210.00510.0

0/3360000.02300.03600.05900.06210.08510.098

10.0

0/2970000.00400.09700.09110.08510.08910.07320.0

0001000.00500.00010.00510.00020.00520.00030.0

1621000.03600.06210.098

10.02520.05130.08730.0

2951000.00800.09510.09320.08130.08930.07740.0

3102000.01010.01020.02030.02040.03050.03060.0

4352000

.07210.03520.00830.06050.03360.09570.0

Table 3. Voltage drop per ft of DC cable

*With Line/Load inversion check & indicator light

**Hospital Grade

rerutcafunaMledoM

NOTIVEL107/9956

NOTIVEL*227/8956

ELGAEyrtneSkcohS

RUOMYES&SSAPNCW-1951

LLEBBUHAYG252FG

TNAYRBITF

25RFG

TNAYRB**ITF28RFG

8 English

Xantrex, in researching the requirements for inverter

use in different markets, provides the following table

that outlines the minimum DC cable size and maximum

fuse/breaker size allowed by different regulatory bodies

in the U.S. There may be other codes and regulations

applicable to your installation:

To make DC wiring connections:

1. Before making any connections, route the positive

and negative battery cables directly to the DC

connection terminals on the Prosine Inverter. Slide

the plastic terminal connector covers (boots) over

the positive and negative cables (the red boot slides

on the positive cable and the black boot slides on

the negative cable). Do not route the cables through

an electrical distribution panel, battery isolator, or

other device that will add additional voltage drops

except for the required fuse or breaker on the

positive battery terminal. Install the inverter so that

the battery wire length is as short as possible. The

connectors on the Prosine Inverter are designed to

fit up to 250 MCM crimp-on ring terminals (either

AMP or ILSCO) or box connectors (these tighten

on connected cable using a set screw). Note, the

coloured terminal covers (boots) fit much better

with crimp-on ring terminals, and these are

recommended over the box connectors.

2. Neatly cut the cables to the correct length and strip

enough insulation to properly install the ring

terminals or connectors. Attach the terminals to both

cables using the crimp tool recommended by the

manufacturer of the ring terminals. There must be

no stray wire strands protruding from the terminal.

Connect the terminal on the positive cable to the

positive battery connector (stud) on the inverter and

tighten with a wrench to a torque of 9–10 ft-lbs

(11.7–13 Nm). Test that the cable is secure and is

connected to the correct positive terminal.

3. An inline fuse between the Prosine Inverter and

the battery is required by regulations for all

installations. Again, refer to Table 4 for examples

of correct fuse sizing for some regulations. This

fuse protects your battery and wiring in case of an

accidental short circuit during installation of the

inverter or later damage to the wiring. The fuse

and fuse holder need to be installed in the positive

side of the DC circuit, as close as possible to the

batteries and within the distance specified by the

applicable installation code. Ensure all other power

and ground connections have been made to the

Prosine Inverter before connecting the DC cables

to the batteries.

4. Connect the cable from the POSITIVE connector

on the Prosine Inverter to the POSITIVE (POS +)

terminal on the fuseholder. Observe the polarities

carefully while performing the installation and do

not reverse the polarities. Route both cables before

making any connections.

5. Connect the DC NEGATIVE cable to the

NEGATIVE (NEG -) terminal on the battery. Next,

connect the cable to the negative terminal on the

inverter. The connection to the negative terminal

of the Prosine Inverter should be the last connection

made. A spark when making this final connection

is normal.

6. For residential installations, a DC wiring enclosure

is required to cover the DC connections. Contact

Xantrex or your distributor for this part. For non-

residential installations, slide the rubber terminal

boot covers up the cable and over the terminal

connections.

CAUTION

Clean battery terminals before making

connections. Wear eye protection to keep

corrosion from coming in contact with eyes.

Figure 4. Battery Connections

CAUTION

An inadvertent reverse polarity connection

may cause damage to the Prosine Inverter

and it will require servicing (internal fuse will

open). Before making the final DC connection,

observe polarities to ensure that the wiring is

correct.

WARNING

Make sure all the DC connections are tight

(torque to 9–10 ft-lbs, 11.7–13Nm). Loose

connections will overheat and could result in

a potential fire hazard.

Table 4. DC wire sizes and inline fuse requirements

ledoM

eniraM noitallatsnI )1(

VR noitallatsnI )2(

laitnediseR noitallatsnI )3(

eriW GWA esuF )A( eriW GWA esuF )A( eriW GWA esuF )A(

V210001 21i0001V

4#5714#0511#051

V420001 42i0001V

8#098#096#07

V210081 21i0081V

1#0031#5220/4052

V420081 42i0081V

6#0014#0512

#521

1 Based on ABYC Recommended Practice E-9, 75°C wire

2 Based on NFPA 70, Article 551, 90°C wire

3 Based on NFPA 70, Article 240 and 310, 75°C wire

Xantrex Prosine Inverter Owner’s Manual

English 9

DC Grounding:

The Prosine Inverter has a lug on the rear panel labeled

Chassis Ground. This lug is used to connect the chassis

of the inverter to your DC ground as is required by

regulations for some installations. Depending on where

the Prosine Inverter is installed, follow the instructions

below that correspond to your installation location.

3. Prosine Inverter Operation

This section details how the unit functions as an

inverter, provides information on the control panel, and

describes operating limits for inverter operation.

3.1 Principles of Operation

The Prosine Inverter converts power from the batteries

in two stages. The first stage is a DC-to-DC converter,

used to raise the low voltage DC input to high voltage

DC. The second stage is the actual inverter stage, taking

the high voltage DC and converting it to a precise, true

sine wave AC output.

The DC-to-DC converter stage uses modern high

frequency power conversion technology that eliminates

the bulky, low frequency (50/60 Hz) based transformers

found in inverters using older technology. The inverter

stage uses advanced power semiconductors that provide

excellent overload capabilities.

3.2 Output Waveform

The AC output waveform of the Prosine Inverter is a

“true sine wave” with typically 1% Total Harmonic

Distortion (THD). Figure 6 illustrates the output

waveform from the inverter. This waveform is nearly

identical to your utility-supplied power and in some

cases where utility power is poor, the Prosine Inverter

delivers cleaner, more precise AC power.

There are many advantages of true sine wave over other

wave forms delivered by other inverters:

•AC powered equipment is designed to operate with

true sine wave. Many loads will perform better

when connected to the Prosine Inverter.

•motor loads start easier

•reduced stress on surge protection circuitry within

the equipment means potentially longer equipment

life

Many advantages of true sine wave are also due to the

absence of the sharp-rising edges of waveforms

prevalent in either modified sine wave or square wave

inverters. Some of these advantages are:

•reduced interference in audio or electronic

equipment, especially those that use less complex

internal power supplies

•significantly reduced in-rush current into capacitive

loads and reduced stress on the output devices of

the inverter, potentially lengthening equipment life

•motor loads generally operate cooler and quieter

without the extra harmonic distortion generated by

a modified sine wave.

lanoitaerceR elciheV snoitallatsnI

fineerg(eriwreppocregralroGWA8#esU sissahcehtottierucesdna)detalusni ni

tniopgnidnuorgehtsallewsaguldnuorg *.)sissahcehtyllausu(elcihevruoy

eniraM lesseV snoitallatsnI

eriuqersec

itcarpdednemmocers'CYBA emasehtevaheriwdnuorgsissahcehttaht ehtsa)yticapma(yticapacgniyrractnerruc eht,e

riwC°09gnisU.selbactupniCD **.tnemeriuqersihtteemseziseriwgniwollof

ledoM)GWA(eziSeriW

V21/00016#

V42/000101

V21/00812#

V42/00816#

laitnediseR snoitallatsnI

tsum

Sine Wave InverterehtfosissahcehT gnidnuorgCDs'metsysehto

tdetcennoceb ehtottierucesdnaeriwreppocesU.tniop dnuorgCDruoydnaguldnuorgsissahc ***.tniop

ledoM)GWA(eziSeriW

V21/00016#

V42/00018#

V21/00814#

V42/00816#

)c(02-155elcitra,07APFNnodesaB* 9-Edna52-ACYBAnodesaB** 54-096dna221-052elcitra,07APFNnodesaB***

Figure 6. True sine wave output (120 V

AC Model)

Figure 5. Principles of Operation

Xantrex Prosine Inverter Owner’s Manual

10 English

3.3 Control Panel

Once the Xantrex Prosine Inverter is properly installed

and connected to batteries, it is ready to begin delivering

AC power to your loads. The control panel is the

interface between you and the inverter. This section

describes the features of this panel and is followed by

other sections that contain inverter operating

information.

1. INVERTER ##

#/I: this switch turns the Prosine

Inverter either ON (I) or to BYPASS-state (##

#). It is

also used to enable or disable POWERSAVE mode

during the power-up sequence. When in the (##

position, models equipped with a transfer relay will be

in the BYPASS mode, where incoming AC power is

passed through to the load. The switch controls the

output of the inverter with models equipped with AC

outlets and does not control the output on hardwire units

equipped with the transfer relay option.

2. LIQUID CRYSTAL DISPLAY (LCD): displays

input current from the battery and battery voltage

numerically. A multi-segment bar graph displays actual

output power in watts from the inverter when a load is

being operated.

3. MULTI-POSITION MOUNT: the control panel is

designed so it can be removed and re-attached to the

chassis in 90° increments depending on the mounting

orientation of the inverter itself. The panel can also

be removed entirely from the unit and mounted

remotely, with the purchase of the optional Interface

Panel.

4. FAULT CONDITION DISPLAY: should a fault

occur, the error will immediately be displayed. An

audible alarm sounds and the back-lighting of the

display will flash to draw attention to the fault

condition (see Section 5.1).

To operate the Prosine Inverter:

1. Turn the unit ON by moving the rocker switch on

the control panel to (I) position. The following

information will be displayed (upon each power-up),

identifying the type and configuration of your Prosine

Inverter:

•Model number (1000 or 1800 watt)

•Input Voltage, Output Voltage and Frequency

configuration

•POWERSAVE mode OFF (factory set default)

Following the display of this information, the control

panel then defaults to the standard display information

of input voltage, input current and output power. When

a load is connected, the output power (watts) is

displayed in bar-graph form.

WARNING

Review the Important Safety Instructions

found at the beginning of this guide before

operating the Prosine Inverter.

Once the standard display screen is shown, the Prosine

Inverter is ready to deliver AC power to your loads.

You can now plug in a load to the front outlet of the

unit, or, for those hardwire versions, into an outlet

connected to the AC output of the inverter. The loads

should operate from the inverter as they would from

utility power. Section 3.5 explains the operating limits

for the Prosine Inverter.

3.4 Prosine POWERSAVE Mode

Your Xantrex Prosine Inverter has a function mode

called POWERSAVE. This “sleep” mode shuts off

much of the power control circuitry of the inverter as

well as the display back-lighting, reducing the stand-

by current draw considerably. With this mode enabled,

the unit draws approx. 1.5 W while powered up but

with no load on the inverter. The Prosine Inverter

detects the presence of a load by sending out pulses

approximately once every 2.5 seconds. Full output

power is available with the detection of a load. The

unit will remain in POWERSAVE mode if the load it

detects is less than 10 W for the 1000 model and less

than 20 W for the 1800 model. This is a factory set

search mode setting and cannot be changed.

You would want to enable POWERSAVE mode if the

inverter is only being used periodically to power loads.

This allows the inverter to draw less power from the

batteries during non-use periods. If the inverter is being

used frequently and your batteries are being recharged

during inverter use (e.g. vehicle alternator), or soon

after inverter use, you can leave POWERSAVE

disabled.

Your inverter is factory default set to POWERSAVE

OFF. To enable the POWERSAVE mode, follow these

steps:

1. Turn the Control Panel switch to (##

#) position

2. Switch the unit back to (I) position. You will see

the power-up information sequence being displayed

as described previously.

3. When the Control Panel displays “POWERSAVE

OFF” turn the switch to (##

#) position, wait for

Xantrex Prosine Inverter Owner’s Manual

Figure 7. Control Panel

Figure 8. Control Panel Screen Sequence

English 11

approximately three seconds, and then turn the

switch back to (I) position. “POWERSAVE ON”

will now be displayed during the start-up sequence

and when the normal state display appears, a small

pointer will be visible, indicating POWERSAVE

mode is enabled. Repeat the same procedure for

disabling POWERSAVE mode.

3.5 Inverter Operating Limits and

Protection Features

Power Output: The Prosine 1000 Inverter will

continuously deliver 1000 watts and the Prosine 1800

delivers 1800 watts continuously. The following table

displays the continuous and peak current ratings as well

as surge rating, depending on the model:

Each unit above will be able to operate all AC loads

rated at or below these power ratings. Some high-

horsepower induction motors used in pumps and other

motor-operated equipment require very high surge

currents to start and the Prosine Inverter/battery

combination may have difficulty starting these loads.

If you have problems with certain loads, ensure that

battery connections are solid, your DC cables are

appropriately sized, and that the battery is of sufficient

capacity and fully charged.

Input Voltage: The Prosine Inverter operates from an

input voltage ranging from:

10 to 16 VDC for 12 V models

20 to 32 VDC for 24 V models

Peak performance for these inverters occurs when DC

input voltage is in the range of 12 volts to 15 volts for

12 V models and 24 volts to 30 volts for 24 V models.

The Prosine Inverter will indicate high and low DC

voltage conditions as follows:

The over-voltage protection and shutdown protects the

inverter against excessive input voltage, should the unit

be connected to a higher voltage than it is designed for

(up to 35VDC—higher voltages may cause damage).

Low input voltage shutdown protects your battery from

being over-discharged. The inverter requires a manual

reset to re-start after shutdown from either high or low

input voltage. Turn the power switch to (##

#) and then

back to (I) to re-start the unit.

Output Overload Protection: A short circuit may be

applied to the output continuously without damage to

any internal components. The Prosine Inverter will shut

down in less than five seconds when the output falls

10% below the nominal voltage as a result of current

limiting.

AC Backfeed Protection: Although the Prosine

Inverter has been designed to withstand incoming AC

at the AC output, this is only a safeguard and continuous

AC backfeed could lead to inverter damage. Avoid

inverter damage by double checking the AC input and

output wiring on hardwire configured models before

applying power and by understanding your source of

AC and where power from the source leads to (e.g. do

not plug a live extension cord into the AC outlet of the

inverter).

Input Reverse Polarity Protection: The internal

circuitry of the Prosine Inverter is protected by an

internal, 32 V, fast-blow fuse as follows:

This fuse is only replaceable by qualified service

personnel. In many reverse polarity conditions, this fuse

will protect internal circuits, however, certain high

voltage/current situations may cause internal damage.

4. Testing

The following simple test procedure should ensure that

the inverter is connected and installed properly.

To test the Prosine Inverter:

1. Double check all wiring terminals on the inverter

to observe correct polarity and secure connections.

2. Turn rocker switch to (I) position.

3. Observe the power-up sequence on the display. The

normal-state inverter display of input current and

input voltage should come up.

4. Plug a test load (e.g. a light bulb) into the outlet of

the Prosine Inverter. The load should function

normally. Observe the output power bar graph—it

should increase with load demand.

5. For hardwire and transfer relay-equipped versions,

plug a load into the AC output leg of the inverter

while input AC is available. Remove input AC. The

load should still operate normally. Replace the

source AC input power and again, the load should

operate normally, indicating proper installation and

function of the transfer relay.

6. Repeat test 4 or 5 with the inverter in

“POWERSAVE” mode.

7. The Prosine Inverter is now ready for operation.

ledoM

CAsuounitnoC tnerruCtuptuO gnitaR

CAkaeP tnerruCtuptuO gnitaR

gnitaRegruS sttaw.xam( 5rofdereviled )sdnoc

0001 A3.8A520051

0081 A51A540092

i0001 A3.4A110051

i0081 A8.7A020092

ledoM

tupnICD revo egatlov mrala

tupnICD revo egatlov nwodtuhs

tupnICD rednu egatlov mrala

tupnICD rednu egatlov nwod

tuhs

V21 sledom CDV8.51CDV0.61CDV5.01CDV0.01

V42 sledom CDV6.13CDV0.23CDV0.12CDV0.02

ledoMledoM&gfM

V42-0001 V42-i0001 ro08NNCdluoG/esuflettiL A08detar08NNAnnamssuB

V21-0081 V21-i0081 A522ageMes

uflettiL

srehtollAA521ageMesuflettiL

Xantrex Prosine Inverter Owner’s Manual

12 English

5. Troubleshooting Guide

This section describes potential installation and configuration problems and solutions, including fault conditions and indicators.

5.1 Fault Conditions and Indicators

The following fault conditions are displayed on the control panel along with an alarm sound and blinking LCD back-light.

The table below provides some troubleshooting tips:

noitacidnIlenaPlortnoCnoitidnoCtluaF noituloS

NWODTUHSTTABHGIHhgihootegatlovyrettaB othctiwsgninrutybretre

vniteseryllaunaM.metsysgnigrahcyrettabhtiwtluafrofkcehC (#(otneht) I.niaga)

NWODTUHSTTABWOLwolootegatlovy

rettaB (othctiwsgninrutybretrevniteseryllaunaM.yrettabegrahC #(otneht) I.niaga)

NWODTUHSDAOLREVOCAelbaborp

,hgihoottnerrucyrettaB daolrevo .retrevninodaolecudeR

NWODTUHSPMETREVOerutarepmet-revometsyS .retrevninoda

olecuderro/dnagniloocdnanoitalitnevevorpmI

NWODTUHSMETSYS NWODTUHSTLUAF_SP NWODTUHSCD-CD

tluaferawdrahmet

sysrodaolrevO otgnihctiwsybretrevniteserotyrTdetcennocsiderasdaolllaerusnE(#(otnehtdna) ItonseodllitstinufI.) .tnemecalperytnarraw/ecivresrofxertnaXroreliater/tnahcrem/rotubirtsidruoytcatnocetarepo

smotpmySdnasmelborP esuaCelbissoPnoituloS

rewolroCDV0.01gnidaerlenaplortnocdnaegatlovtuptuooN .)sledomV42

noCDV4.02( .nwodtuhsegatlovtupniwoL .elbacdnasnoitcennockcehc,yrettabegrahceR

.noitacidniegatlovon,egatl

ovtuptuooN (otdehctiwsretrevnI ##

## .)

.retrevniotrewopyrettaboN

noitcennocytiralopCDesreveR .nepoesuflanr

etni—

(othctiwsrewopretrevnInruT I.)

.esufyrettabkcehC.retrevnIotgniriwkcehC

tcerroc(esufecalperdnakcehcn

aicinhcetecivresdeifilauqevaH .ytiraloptcerrocevresbO.)tinufoedisninodetonesuftnemecalper

rehgihroCDV0.

61gnidaerlenaplortnocdnaegatlovtuptuooN .)sledomV42noCDV0.23( .nwodtuhsegatlovtupnihgiH egatlovyrettabtcerrocotdetcennocsiretrevnIehterusekaM

.metsysgnigrahcfonoitalugerkcehC

wolebrotacidniegatloV.emitehtlla

nogninrawyrettabwoL .)sledomV42noCDV0.22(CDV0.11 .gniriwCDrooP

.noitidnocyrettabrooP

.snoitcennocdilosekamdnaelbacreporpesU

.yrettabwenesuroyrettabegrahC

WARNING

Do not open or disassemble the Prosine Inverter. See Section 6 for instructions on obtaining service for the inverter. Attempting to service the unit yourself may result in a risk of

electrical shock or fire.

Xantrex Prosine Inverter Owner’s Manual

English 13

Xantrex Prosine Inverter Owner’s Manual

6. Warranty and Return Information

Warranty

What does this warranty cover and how long does it last? This Limited

Warranty is provided by Xantrex Technology Inc. (“Xantrex”) and covers defects

in workmanship and materials in your Xantrex Prosine Sine Wave Inverter. This

Warranty Period lasts for 24 months from the date of purchase at the point of sale

to you, the original end user customer, unless otherwise agreed in writing. You

will be required to demonstrate proof of purchase to make warranty claims.

This Limited Warranty is transferable to subsequent owners but only for the

unexpired portion of the Warranty Period. Subsequent owners also require

original proof of purchase as described in “What proof of purchase is required?”

What will Xantrex do? During the Warranty Period Xantrex will, at its option,

repair the product (if economically feasible) or replace the defective product free

of charge, provided that you notify Xantrex of the product defect within the

Warranty Period, and provided that Xantrex through inspection establishes the

existence of such a defect and that it is covered by this Limited Warranty.

Xantrex will, at its option, use new and/or reconditioned parts in performing

warranty repair and building replacement products. Xantrex reserves the right to

use parts or products of original or improved design in the repair or replacement.

If Xantrex repairs or replaces a product, its warranty continues for the remaining

portion of the original Warranty Period or 90 days from the date of the return

shipment to the customer, whichever is greater. All replaced products and all parts

removed from repaired products become the property of Xantrex.

Xantrex covers both parts and labor necessary to repair the product, and return

shipment to the customer via a Xantrex-selected non-expedited surface freight

within the contiguous United States and Canada. Alaska, Hawaii and outside of

the United States and Canada are excluded. Contact Xantrex Customer Service

for details on freight policy for return shipments from excluded areas.

How do you get service? If your product requires troubleshooting or warranty

service, contact your merchant. If you are unable to contact your merchant, or the

merchant is unable to provide service, contact Xantrex directly at:

Telephone: 1 800 670 0707 (toll free North America), 1 408 987 6030 (direct)

Fax: 1 800 994 7828 (toll free North America), 1 604 422 2756 (direct)

Email: [email protected]

Website: www.xantrex.com

Direct returns may be performed according to the Xantrex Return Material

Authorization Policy described in your product manual. For some products,

Xantrex maintains a network of regional Authorized Service Centers. Call

Xantrex or check our website to see if your product can be repaired at one of

these facilities.

What proof of purchase is required? In any warranty claim, dated proof of

purchase must accompany the product and the product must not have been

disassembled or modified without prior written authorization by Xantrex.

Proof of purchase may be in any one of the following forms:

• The dated purchase receipt from the original purchase of the product

at point of sale to the end user; or

• The dated dealer invoice or purchase receipt showing original

equipment manufacturer (OEM) status; or

• The dated invoice or purchase receipt showing the product

exchanged under warranty.

What does this warranty not cover? Claims are limited to repair and

replacement, or if in Xantrex’s discretion that is not possible, reimbursement up

to the purchase price paid for the product. Xantrex will be liable to you only for

direct damages suffered by you and only up to a maximum amount equal to the

purchase price of the product.

This Limited Warranty does not warrant uninterrupted or error-free operation of the product

or cover normal wear and tear of the product or costs related to the removal, installation, or

troubleshooting of the customer’s electrical systems. This warranty does not apply to and

Xantrex will not be responsible for any defect in or damage to:

a) the product if it has been misused, neglected, improperly installed, physically

damaged or altered, either internally or externally, or damaged from improper use or

use in an unsuitable environment;

b) the product if it has been subjected to fire, water, generalized corrosion, biological

infestations, or input voltage that creates operating conditions beyond the maximum

or minimum limits listed in the Xantrex product specifications including, but not

limited to, high input voltage from generators and lightning strikes;

c) the product if repairs have been done to it other than by Xantrex or its authorized

service centers (hereafter “ASCs”);

d) the product if it is used as a component part of a product expressly warranted by

another manufacturer;

e) component parts or monitoring systems supplied by you or purchased by Xantrex at

your direction for incorporation into the product;

f) the product if its original identification (trade-mark, serial number) markings have

been defaced, altered, or removed;

g) the product if it is located outside of the country where it was purchased; and

h) any consequential losses that are attributable to the product losing power whether by

product malfunction, installation error or misuse.

Disclaimer

Product

THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY XANTREX IN

CONNECTION WITH YOUR XANTREX PRODUCT AND IS,WHERE PERMITTED BY LAW,IN LIEU OF ALL

OTHER WARRANTIES,CONDITIONS,GUARANTEES,REPRESENTATIONS,OBLIGATIONS AND LIABILITIES,

EXPRESS OR IMPLIED,STATUTORY OR OTHERWISE IN CONNECTION WITH THE PRODUCT,HOWEVER

ARISING (WHETHER BY CONTRACT,TORT,NEGLIGENCE,PRINCIPLES OF MANUFACTURER’S LIABILITY,

OPERATION OF LAW,CONDUCT,STATEMENT OR OTHERWISE), INCLUDING WITHOUT RESTRICTION ANY

IMPLIED WARRANTY OR CONDITION OF QUALITY,MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO

THE EXTENT REQUIRED UNDER APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE LIMITED IN

DURATION TO THE PERIOD STIPULATED UNDER THIS LIMITED WARRANTY.

IN NO EVENT WILL XANTREX BE LIABLE FOR: (A)ANY SPECIAL,INDIRECT,INCIDENTAL OR

CONSEQUENTIAL DAMAGES,INCLUDING LOST PROFITS,LOST REVENUES,FAILURE TO REALIZE

EXPECTED SAVINGS,OR OTHER COMMERCIAL OR ECONOMIC LOSSES OF ANY KIND,EVEN IF XANTREX

HAS BEEN ADVISED,OR HAD REASON TO KNOW,OF THE POSSIBILITY OF SUCH DAMAGE, (B)ANY

LIABILITY ARISING IN TORT,WHETHER OR NOT ARISING OUT OF XANTREX’S NEGLIGENCE,AND ALL

LOSSES OR DAMAGES TO ANY PROPERTY OR FOR ANY PERSONAL INJURY OR ECONOMIC LOSS OR

DAMAGE CAUSED BY THE CONNECTION OF A PRODUCT TO ANY OTHER DEVICE OR SYSTEM,AND (C)ANY

DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF MISUSE OR ABUSE,OR THE INCORRECT

INSTALLATION,INTEGRATION OR OPERATION OF THE PRODUCT.

IF YOU ARE A CONSUMER (RATHER THAN A PURCHASER OF THE PRODUCT IN THE COURSE OF A

BUSINESS)AND PURCHASED THE PRODUCT IN A MEMBER STATE OF THE EUROPEAN UNION,THIS

LIMITED WARRANTY SHALL BE SUBJECT TO YOUR STATUTORY RIGHTS AS A CONSUMER UNDER THE

EUROPEAN UNION PRODUCT WARRANTY DIRECTIVE 1999/44/EC AND AS SUCH DIRECTIVE HAS BEEN

IMPLEMENTED IN THE EUROPEAN UNION MEMBER STATE WHERE YOU PURCHASED THE PRODUCT.

FURTHER,WHILE THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,YOU MAY HAVE OTHER

RIGHTS WHICH MAY VARY FROM EU MEMBER STATE TO EU MEMBER STATE OR,IF YOU DID NOT

PURCHASE THE PRODUCT IN AN EU MEMBER STATE,IN THE COUNTRY YOU PURCHASED THE PRODUCT

WHICH MAY VARY FROM COUNTRY TO COUNTRY AND JURISDICTION TO JURISDICTION.

Return Material Authorization Policy

For those products that are not being repaired in the field and are being returned to Xantrex,

before returning a product directly to Xantrex you must obtain a Return Material

Authorization (RMA) number and the correct factory “Ship To” address. Products must also

be shipped prepaid. Product shipments will be refused and returned at your expense if they

are unauthorized, returned without an RMA number clearly marked on the outside of the

shipping box, if they are shipped collect, or if they are shipped to the wrong location.

When you contact Xantrex to obtain service, please have your instruction

manual ready for reference and be prepared to supply:

• The serial number of your product

• Information about the installation and use of the unit

• Information about the failure and/or reason for the return

• A copy of your dated proof of purchase

Return Procedure

Package the unit safely, preferably using the original box and packing materials.

Please ensure that your product is shipped fully insured in the original

packaging or equivalent. This warranty will not apply where the product is

damaged due to improper packaging.

Include the following:

• The RMA number supplied by Xantrex Technology Inc. clearly

marked on the outside of the box.

• A return address where the unit can be shipped. Post office boxes

are not acceptable.

• A contact telephone number where you can be reached during

work hours.

• A brief description of the problem.

Ship the unit prepaid to the address provided by your Xantrex customer service

representative.

If you are returning a product from outside of the USA or Canada

In addition to the above, you MUST include return freight funds and are fully

responsible for all documents, duties, tariffs, and deposits.

If you are returning a product to a Xantrex Authorized Service Center

(ASC)

A Xantrex return material authorization (RMA) number is not required.

However, you must contact the ASC prior to returning the product or presenting

the unit to verify any return procedures that may apply to that particular facility

and that the ASC repairs this particular Xantrex product.

Out of Warranty Service

If the warranty period for your product has expired, if the unit was damaged by

misuse or incorrect installation, if other conditions of the warranty have not

been met, or if no dated proof of purchase is available, your unit may be

serviced or replaced for a flat fee.

To return your product for out of warranty service, contact Xantrex Customer

Service for a Return Material Authorization (RMA) number and follow the other

steps outlined in “Return Procedure”.

Payment options such as credit card or money order will be explained by the

Customer Service Representative. In cases where the minimum flat fee does not

apply, as with incomplete units or units with excessive damage, an additional

fee will be charged. If applicable, you will be contacted by Customer Service

once your unit has been received.

ADVANTAGES:

More resistant to over-charging since they can be filled with

water. Cheaper than other batteries.

DISADVANTAGES:

Must be filled with DISTILLED water and usually require

equalization. Maintenance required.

SEALED FLOODED BATTERIES:

DELCO:Voyager

IDENTIFYING FEATURES:

Vents which look like they are removable but are not. Sold

as “Maintenance Free” at attractive prices.

ADVANTAGES:

Less maintenance required than Flooded. No need to fill

with water. Less expensive.

DISADVANTAGES:

Less resistant to over-charging because they consume water

but cannot be refilled.

RECOMBINANT FLOODED (SEALED)

BATTERIES:

HAWKER ENERGY: Genesis

OPTIMA: Yellow Top

GNB INDUSTRIAL: Evolyte

IDENTIFYING FEATURES:

Vents are often concealed. Sold using the following phrases:

Recombinant, Valve Regulated, Maintenance Free, Starved

Electrolyte.

ADVANTAGES:

Require no maintenance. Non-spillable

DISADVANTAGES:

Can be damaged by equalization. Generally more expensive.

GEL SEALED BATTERIES:

SONNENSCHEIN: Prevailer

WEST MARINE: SeaGel

IDENTIFYING FEATURES:

Sold as either “Gel” or “Gelled Electrolyte” batteries.

ADVANTAGES:

Require no maintenance. Often can be used on their side.

Non-spillable. Low self-discharge. Less damage from being

left discharged.

DISADVANTAGES:

Damaged by equalization. Generally more expensive.

14 English Xantrex Prosine Inverter Owner’s Manual

7. Appendices

7.1 Battery Type

This appendix explains some of the differences between

the different lead acid batteries to help you choose a battery

which best suits your needs.

The lead-acid battery which is probably most common is

the starting battery in your automobile. An automotive

starting battery is designed to deliver a large amount of

current for a short period of time (so it can start your engine).

Only a small portion of the battery´s capacity is used when

starting the engine and it is quickly recharged by the running

engine. It is not designed for repeated charge-discharge

cycles where the battery is almost completely discharged

and then recharged. Starting batteries used in this kind of

deep discharge service will wear out rapidly.

Your Xantrex Prosine Inverter is designed to be used with

deep-cycle lead acid batteries. These batteries are designed

for deep discharge service where they will be repeatedly

charged and discharged. This type of battery is often labeled

as a marine, recreational vehicle, or golf cart battery.

Xantrex recommends you use one or more of these batteries

separated from the starting battery of your vehicle or boat

with a battery isolator.

The many different types of deep-cycle lead acid batteries

can be grouped into four categories: flooded (or wet), sealed

flooded (“maintenance free”), recombinant flooded (often

“starved electrolyte”), and gel batteries. The table that

follows summarizes these battery types, identifying features,

advantages and disadvantages.

FLOODED BATTERIES:

TROJAN: Golf Cart, Superior, Pacer

WEST MARINE: Sea Volt

MOTOMASTER:Nautilus

IDENTIFYING FEATURES:

Vents which can be removed to fill the battery with water.

Low price and higher maintenance.

7.2 Battery Size

Just as important as the type of battery selected for use

with your Xantrex Prosine Inverter is the subject of

battery size (capacity). There are a number of different

standards for rating battery capacity. Automotive

starting batteries are normally rated by cranking amps.

This is not a relevant rating for continuous use. Deep

cycle batteries are rated either by reserve capacity in

minutes or by amp-hours.

Battery reserve capacity is a measure of how long a

battery can deliver a certain amount of current—usually

25 amps. For example, a battery with a reserve capacity

of 180 minutes can deliver 25 amps for 180 minutes

before it is completely discharged.

Amp-hour capacity is a measure of how many amps a

battery can deliver for a specified length of time—

usually 20 hours. For example, a typical marine or RV

battery rated for 100 amp hours can deliver 5 amps for

20 hours. (5 amps x 20 hours = 100 amp hours)

You can expect performance from the inverter to suffer

with the use of a small, low amp-hour rated battery

(for example, 50 Ah). Even if your battery is in excellent

shape and fully charged you will likely experience

poor surge power performance and unsatisfactory

operating time with anything but a small AC load.

Xantrex recommends a minimum battery size of 200

Ah for moderate loads (less than 1000 W) and greater

than 400 Ah for heavy loads.

To determine how large a battery or battery bank you

require for equipment running from the inverter, simply

add together the power requirements for all electrical

devices that you will be running multiplied by their

approximate running times in hours between battery

recharges. Each device will be rated in either watts,

volts and amps, or VA. For this calculation, all three of

these ratings are equivalent (i.e. volts x amps = watts

= VA). The following example, based on battery

recharging every three days, illustrates the calculation:

1 Power Consumption x Operating Time

Convert the watt hours to amp hours by dividing total

watt hours by 10:

1495 watt hours/10 = 149.5 amp hours

A 150 amp hour battery is required to supply enough

power for the above loads, and become completely

discharged. Ideally, you normally want to discharge

your battery to only 50% capacity, so for the above loads,

you would require about 300 amp hours of battery

capacity.

When sizing your battery, be generous. More capacity

is better since you will have more reserve capacity, and

your battery will not be discharged as deeply. Battery

life is directly dependent on how deeply the battery is

discharged. The deeper the discharge, the shorter the

battery life.

As your power requirements increase, to obtain

sufficient battery capacity, you may need to use more

than one battery. Two identical batteries can be

connected positive to positive and negative to negative

in a parallel system that doubles the capacity and

maintains the voltage of a single battery. It is not

recommended to connect batteries from different

manufacturers or with different amp-hour ratings or

with different battery electrolytes in parallel. Decreased

battery life may result.

daoL rewoP noitpmusnoC emiTgnitarepO sruohttaW

RCV&VTW511srh3 )yadreprh1( 543

eeffoC rekaM W057rh1 )yadrep.nim02( 057

evaworciM nevO W008srh5.0 )yadrep.nim01( 004

TOT5941

English 15

Xantrex Prosine Inverter Owner’s Manual

8. Performance Graphs

8.1 Power Derating Curve

As with all inverters, the amount of continuous power

that the Xantrex Prosine Inverters can deliver without

overheating is limited by ambient (surrounding air)

temperature. The following “Power Derating Curve

vs. Temperature” illustrates the relationship between

power output and ambient temperature.

Operating the unit above this temperature will result

in thermal shutdown or decreased performance. At input

voltages less than 12 V or 24 V, the unit runs warmer

which will cause thermal shutdowns at temperatures

below these ambient temperature guidelines.

Operating the unit in conditions outside the power and

temperature limits (above and to the right of the derating

curves) will result in thermal shutdown and/or

significantly decreased performance. In addition,

operation in this range is outside of the ratings covered

by the product’s regulatory approvals.

16 English Xantrex Prosine Inverter Owner’s Manual

La page charge ...

Xantrex Technologies 1800 Manuel utilisateur

Marque: Xantrex Technologies

Modèle: 1800

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Xantrex Technologies 1800 User manual
español: Xantrex Technologies 1800 Manual de usuario
Deutsch: Xantrex Technologies 1800 Benutzerhandbuch

Xantrex Technologies 1800 Manuel utilisateur

Xantrex Technologies 1800 Manuel utilisateur

dans d''autres langues

Autres documents