Hikoki NR3675DD Manuel utilisateur

Instruction and safety manual

Manuel d’instructions et de sécurité

Instrucciones y manual de seguridad

DANGER

Improper use of this Nailer can result in death or serious injury!

This Manual contains important information about product safety.

Read and understand this Manual before operating the Nailer.

Never allow anyone who has not reviewed this manual to use the tool.

This manual should be stored in safe place.

DANGER

Une utilisation incorrecte et sans respecter la sécurité de ce cloueur risque d’entraîner

la mort ou des blessures graves !

Ce manuel renferme des instructions importantes sur la sécurité de l’outil.

Lire et bien assimiler ce manuel avant d’utiliser le cloueur.

Cet outil ne doit jamais être utilisé par une personne n’ayant pas pris connaissance du

manuel.

Ce mode d’emploi doit être conservé dans un endroit sûr.

PELIGRO

¡La utilización inadecuada e insegura de este clavador puede resultar en lesiones serias

o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y entienda este manual antes de utilizar el martillo neumático.

La herramienta no deberá utilizarse sin haber leído previamente este manual.

Este manual debe ser guardado en un lugar seguro.

Model

Modèle

Modelo

NR 3675DD

Cordless Duplex Nailer

Cloueuse sans ﬁ l pour clous à deux têtes

Clavadora inalambrica para clavos duplex

2

English

IMPORTANT INFORMATION

Read and understand tool labels and all of the operating instructions, safety precautions and warnings

in this manual before operating or maintaining this nailer.

Failure to follow warnings could result in DEATH or SERIOUS INJURY.

Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it

occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the

operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by DANGERS and WARNINGS

on the Nailer and in this Manual.

NEVER use this Nailer for applications other than those speciﬁ ed in this Manual.

DEFINITIONS OF SIGNAL WORDS

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

EXPLANATION OF THE NAILING ACTION OF THE metabo HPT NAILER

○

FULL SEQUENTIAL ACTUATION MECHANISM:

First, press the push lever against the wood; next, pull the trigger to drive the fastener. Follow the same sequence to

continue driving fasteners.

○

CONTACT ACTUATION MECHANISM:

First, pull the trigger; next, press the push lever against the wood to drive the fastener.

If the trigger is held back, a fastener will be driven each time the push lever is pressed against the wood.

3

English

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the oﬀ -position before

connecting to power source and/or battery

pack, picking up or carrying the tool.

Carrying power tools with your ﬁ nger on the

switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4

English

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk

of injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SAFETY — Continued

5

English

NAILER SAFETY WARNINGS

WARNING

– Always assume that the tool contains fasteners.

Careless handling of the nailer can result in

unexpected ﬁ ring of fasteners and personal injury.

– Do not point the tool towards yourself or anyone

nearby. Unexpected triggering will discharge the

fastener causing an injury.

– Do not actuate the tool unless the tool is placed

ﬁ rmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be

deﬂ ected away from your target.

– Disconnect the tool from the power source when

the fastener jams in the tool. While removing a

jammed fastener, the nailer may be accidentally

activated if it is plugged in.

– Use caution while removing a jammed fastener.

The mechanism may be under compression and

the fastener may be forcefully discharged while

attempting to free a jammed condition.

–

Do not use this nailer for fastening electric cables.

It is not designed for electric cable installation and

may damage the insulation of electric cables thereby

causing electric shock or ﬁ re hazards.

SAFETY — Continued

IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS

READ ALL INSTRUCTIONS

DANGER

1. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS.

When operating the Nailer, always wear safety glasses with side shields, and make sure others in work

area wear safety glasses, too.

Safety glasses must conform to the requirements of American National Standards Institute, ANSI Z87.1

and provide protection against ﬂ ying particles both from the front and side.

The employer must enforce the use of safety glasses by the Nailer operator and others in work area.

WARNING

2. NEVER POINT TOOL AT YOURSELF OR OTHERS

IN WORK AREA.

Always assume the Nailer contains

fasteners.

Never point the Nailer at yourself toward

yourself or others, whether it contains

fasteners or not.

If fasteners are mistakenly driven, it can

lead to severe injuries.

Never engage in horseplay with the

Nailer.

Respect the Nailer as a working

implement.

3. KEEP FINGERS AWAY FROM TRIGGER

WHEN NOT DRIVING FASTENERS TO AVOID

ACCIDENTAL FIRING.

Never carry the Nailer with ﬁ nger on trigger since

you could drive a fastener unintentionally and injure

yourself or someone else.

Always carry the Nailer by the handle only.

4. CHOICE OF TRIGGERING METHOD IS

IMPORTANT.

Read and understand section titled “Methods of

operation.” (pages 23 - 24)

6

English

5. ALWAYS WEAR EAR AND HEAD PROTECTION.

Always wear ear protection to protect your ears from

loud noise.

Always wear head protection to protect your head

from ﬂ ying objects.

6. OPERATE WITHIN PROPER TEMPERATURE

RANGE.

The operating environment for this device is between

32°F (0°C) and 104°F (40°C) so ensure use within this

temperature range.

The device may fail to operate below 32°F (0°C) or

above 104°F (40°C).

7. STORE NAILER PROPERLY, AND BATTERY

REMOVED.

When not in use, the Nailer, battery and battery

charger should be stored in a dry place. Keep out of

reach of children. Lock the storage area.

8. KEEP WORK AREA CLEAN.

Cluttered areas invite injuries. Clear all work areas of

unnecessary tools, debris, furniture, etc.

9. KEEP VISITORS AWAY.

Do not let visitors handle the Nailer.

All visitors should be kept safely away from work

area.

10. DRESS PROPERLY.

Do not wear loose clothing or jewelry as they can be

caught in moving parts.

Rubber gloves and nonskid footwear are

recommended when working outdoors.

Wear protective hair covering to contain long hair.

11. CHECK PUSH LEVER BEFORE USE.

Make sure the push lever operates properly.

(The push lever may be called “Safety”.) Never

use the Nailer unless the push lever is operating

properly, otherwise the Nailer could drive a fastener

unexpectedly. Do not tamper with or remove the push

lever, otherwise the push lever becomes inoperable.

12. KEEP ALL SCREWS AND COVERS TIGHTLY IN

PLACE.

Keep all screws and covers tightly mounted. Check

their condition periodically.

Never use the Nailer if parts are missing or damaged.

13. DO NOT LOAD FASTENERS WITH TRIGGER OR

PUSH LEVER DEPRESSED.

When loading fasteners into the Nailer,

1) do not depress the trigger;

2) do not depress the push lever; and

3) keep the Nailer pointed downward.

14. KEEP FACE, HANDS AND FEET AWAY FROM

FIRING HEAD DURING USE.

Never place your face, hands or feet closer than

8 inches (200 mm) from the ﬁ ring head.

A serious injury can result if the fasteners are

deﬂ ected by the workpiece, or are driven away from

the point of entry.

15. PLACE NAILER PROPERLY ON WORKPIECE.

Do not drive fasteners on top of other fasteners or

with the Nailer at too steep of an angle; the fasteners

can ricochet and hurt someone.

16. BEFORE STARTING WORK, CHECK THE

FASTENING OPERATION SWITCHING DEVICE.

This metabo HPT nailer includes a fastening

operation switching device.

Before starting work, check the setting of the

operation switching device.

If the switching device is not set properly, the nailer

will not operate correctly.

17. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.

If the push lever is unintentionally allowed to re-

contact the workpiece following recoil, an unwanted

fastener will be driven.

In order to avoid this undesirable double ﬁ re,

○

Intermittent operation (Trigger ﬁ ring)

1) Set the switching device to FULL SEQUENTIAL

ACTUATION MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

○

Continuous operation (Push lever ﬁ ring)

1) Do not press the nailer against the wood with

excessive force.

2) Separate the nailer from the wood as it recoils

after fastening.

18. DO NOT DRIVE FASTENERS INTO THIN

BOARDS OR NEAR CORNERS AND EDGES OF

WORKPIECE.

The fasteners can be driven through or away from the

workpiece and hit someone.

19. BE CAREFUL OF FASTENERS AFTER DRIVING

THEM IN.

The heads of the fasteners protrude from the surface

of the workpiece because they are duplex fasteners.

20. DO NOT DRIVE FASTENERS INTO MATERIALS

OTHER THAN WOOD.

If fasteners are driven into hard materials such as

metal, the fasteners can ricochet and hurt someone.

21. NEVER DRIVE FASTENERS FROM BOTH SIDES

OF A WALL AT THE SAME TIME.

The fasteners can be driven into and through the wall

and hit a person on the opposite side.

SAFETY — Continued

7

English

22. CHECK FOR LIVE WIRES.

Avoid the risk of severe electrical shock by checking

for live electrical wires that may be hidden by walls,

ﬂ oors or ceilings. Turn oﬀ the breaker switch to

ensure there are no live wires.

23. DO NOT OVERREACH.

Keep proper footing and balance at all times.

24. NEVER USE NAILER WHICH IS DEFECTIVE OR

OPERATING ABNORMALLY.

If the Nailer appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange for

repairs by a metabo HPT authorized service center.

25. REMOVE ALL REMAINING FASTENERS AND

BATTERY FROM NAILER WHEN:

1) doing maintenance and inspection;

2) checking proper operation of push lever and

trigger;

3) clearing a jam;

4) it is not in use;

5) leaving work area;

6) moving it to another location; and

7) handing it to another person.

Never attempt to clear a jam or repair the Nailer unless

you have removed battery and all remaining fasteners

from the Nailer.

The Nailer should never be left unattended since people

who are not familiar with the Nailer might handle it and

injure the themselves.

26. REMOVE BATTERY FROM NAILER WHEN:

1) loading fasteners;

2) turning the adjuster.

27. STAY ALERT.

Watch what you are doing. Use common sense.

Do not operate the Nailer when you are tired.

The Nailer should never be used by you if you are

under the inﬂ uence of alcohol, drugs or medication

that makes you drowsy.

28. HANDLE NAILER CORRECTLY.

Operate the Nailer according to this Manual.

Never allow the Nailer to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

29. NEVER USE NAILER FOR APPLICATIONS OTHER

THAN THOSE SPECIFIED IN THIS MANUAL.

30. HANDLE NAILER CAREFULLY.

Do not drop the Nailer or strike the Nailer against

hard surfaces; and do not scratch or engrave signs

on the Nailer. Handle the Nailer carefully.

31. MAINTAIN NAILER WITH CARE.

Keep the Nailer clean and lubricated for better and

safer performance.

32. USE ONLY PARTS, ACCESSORIES OR

FASTENERS SUPPLIED OR RECOMMENDED BY

metabo HPT.

Unauthorized parts, accessories, or fasteners may

void your warranty and can lead to malfunction and

resulting injuries.

Only service personnel trained by metabo HPT,

distributor or employer shall repair the Nailer.

33. NEVER MODIFY OR ALTER A NAILER.

Doing so may cause it to malfunction and personal

injuries may result.

34. NEVER allow magnets (or similar magnetic

devices) to be adjacent to the nailer, because the

nailer has a magnetic sensor inside.

Doing so will cause a failure or risk of injury by

malfunction.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery multi volt type series and BSL18

series. Other type of batteries may burst causing

personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

SAFETY — Continued

8

English

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than but less

than Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

Follow these instructions to avoid the risk of injury:

WARNING

Improper use of the battery or battery charger can

lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged

or is completely worn out. The battery can explode in

a ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 14°F

(-10°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

SAFETY — Continued

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage rating

by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YSL3 battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY metabo HPT BATTERY TYPE

BSL36A18X. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger;

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

9

English

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the

power tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or

foul odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water,

can cause damage resulting in ﬁ re or explosion.

Store your battery in a cool, dry place, away from

combustible and ﬂ ammable items. Corrosive gas

atmospheres must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

SAFETY — Continued

10

English

○

Either install the battery in the power tool or

store by securely pressing into the battery

cover until the ventilation holes are concealed to

prevent short-circuits.

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations

of the destination country.

Wh

Power Output

2 to 3 digit number

USB DEVICE CONNECTION

PRECAUTIONS

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

EMPLOYER’S RESPONSIBILITIES

1. Ensure that this MANUAL is available to operators

and personnel performing maintenance.

2. Ensure that Nailers are used only when operators and

others in work area are wearing EYE PROTECTOR.

3. Enforce the use of EYE PROTECTOR by operators

and others in work area.

4. Keep Nailers in safe working order.

5. Maintain Nailers properly.

6. Ensure that Nailers which require repair are not

further used before repair.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

SAFETY — Continued

11

English

OPERATION

NOTE

The information contained in this Manual is designed to assist you in the safe operation of the Nailer.

Some illustrations in this Manual may show details or attachments that diﬀ er from those on your own Nailer.

NAME OF PARTS

1. Cordless Duplex Nailer

Trigger

Top cover

Magazine

Firing head

(outlet)

Lock lever

Handle

Battery

Hook

Push lever Feeder knob

Nail feeder (B)

Power indicator Power

switch

Information indicator Nailing

operation switch

Nailing operation

indicator

2. Battery 3. Battery Charger

Battery Latch

Ventilation holes

Terminals

Battery cover

Ventilation

holes

Body

Cord

Nameplate

Charge

indicator lamp

Guide rail

12

English

SPECIFICATIONS

1. Cordless Duplex Nailer

Model NR3675DD

Motor DC Brushless

Applicable Nail Length 1-3/4" to 3" (45 mm to 75 mm)

Nail Loading capacity [nails] 35

Firing mode Full sequential / Contact (Selectable)

Cycle rate [Nails/ second] 2 (Intermittent)

Battery Model BSL36A18X

Type Li-ion battery

Voltage DC 36 V / 18 V

Weight Include battery 10.8 lbs. (4.9 kg)

Dimension

Length × Height × Width 13-1/2" × 13-7/8" × 5-3/8"

(342 mm × 352 mm × 137 mm)

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL36A18X : Approx. 32 min

Charging voltage DC 14.4–18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

NOTE The charging time may vary according to temperature and power source voltage.

13

English

NAIL SELECTION

WARNING

●

Be sure to use only the genuine metabo HPT

nails for the NR3675DD in Table 2. The use of

any other nails can result in tool malfunction

and/or nail breakdown, leading to serious

injuries.

Only nails shown in the Table below can be driven with

this Nailer.

Dimensions of nails

NR3675DD

Plastic-collated strip nails

Duplex nails Min. Max.

.131" (3.3 mm)

1-3/4" (45 mm)

.205" (5.2 mm)

1/2" (12.7 mm)

.232" (5.9 mm)

.131" (3.3 mm)

3" (75 mm)

.205" (5.2 mm)

1/2" (12.7 mm)

.232" (5.9 mm)

Table 2 Applicable nails

Type Length Nails/Strip Code No.

Plastic-collated Duplex nail

1-3/4" (45 mm) 25 50214-6D

2-1/4" (57 mm) 25 50234-8D

3" (75 mm) 25 50312-16D

21°

14

English

ACCESSORIES

DANGER

●

Accessories other than those shown below

can lead to malfunction and resulting

injuries.

STANDARD ACCESSORIES

NR3675DD

(XC)

Safety glasses ....................................................................................... 1

Battery (BSL36A18X) ............................................................................ 1

Battery Charger (UC18YSL3) ................................................................ 1

Contractor bag ...................................................................................... 1

Battery cover (Code No. 329897) ......................................................... 1

Allen wrench for M5 screw .................................................................... 1

Allen wrench for M4 screw .................................................................... 1

NR3675DD

(NN)

Safety glasses ....................................................................................... 1

Allen wrench for M5 screw .................................................................... 1

Allen wrench for M4 screw .................................................................... 1

OPTIONAL ACCESSORIES

sold separately

○

BATTERY (BSL36A18X)

NOTE

Accessories are subject to change without any

obligation on the part of metabo HPT.

15

English

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○ The power source voltage is stated on the nameplate.

○ The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on

the nameplate, the charger will burn out.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Firmly insert the battery into the battery charger.

Charge

indicator lamp

Guide rail

Battery

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green. (See

Table 3)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 3, according to the condition of the

battery charger or the battery.

APPLICATIONS

○

Concrete form building.

REMOVAL AND INSTALLATION

METHOD OF BATTERY

CAUTION

●

Be sure keep the ﬁ ngers away from the trigger

and push lever away from the wood.

○

How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

○

How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery.

Battery

Push

Pull out

Insert

Handle

Latch

16

English

Table 3

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging Blinks

(RED)

Lights for 0.5 seconds. Does not light

for 0.5 seconds.

(oﬀ for 0.5 seconds) Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light

for 1 second.

(oﬀ for 1 second) Battery capacity at less than

50%

Blinks

(BLUE)

Lights for 1 second. Does not light for

0.5 seconds.

(oﬀ for 0.5 seconds) Battery capacity at less than

80%

Lights

(BLUE) Lights continuously Battery capacity at more than

80%

Charging

complete Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby Blinks

(RED)

Lights for 0.3 seconds. Does not light

for 0.3 seconds.

(oﬀ for 0.3 seconds)

Battery overheated. Unable

to charge. (Charging will

commence when battery cools)

Charging

impossible Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light

for 0.1 seconds.

(oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 4, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 4

Rechargeable

batteries Temperatures at which the battery

can be recharged

BSL36A18X 32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 5 Charging time

Charger

Battery UC18YSL3

BSL36A18X Approx. 32 min.

NOTE

The recharging time may vary according to the

ambient temperature.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery

charger after use, and then keep it.

17

English

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2–3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated

because it has been left for a long time in a

location subject to direct sunlight or because the

battery has just been used, the charge indicator

lamp of the charger lights for 0.3 seconds, does

not light for 0.3 seconds (oﬀ for 0.3 seconds). In

such a case, ﬁ rst let the battery cool, then start

charging.

●

When the charge indicator lamp ﬂ ickers (at

0.2–second intervals), check for and take out

any foreign objects in the charger’s battery

installation hole. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

HOW TO RECHARGE USB DEVICE

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery

○

Charging a USB device from a electrical outlet

18

English

○

Charging a USB device and battery from a

electrical outlet

(2) Turn the USB power switch ON

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power

switch

USB power

indicator lamp

Rubber cover

USB port

USB cable

(3) Connect the USB cable.

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

○

When the power cord is not plugged into an outlet

and the battery runs out of power, power output will

stop and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out,

change the battery or plug the power cord into an

electrical outlet.

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the

power cord from the electrical outlet.

○

Remove the battery from the charger and place the

rubber cover over the USB port.

BEFORE OPERATION

Read section titled “SAFETY” (pages 3–10).

Make sure of the followings before operation.

PREPARING THE BATTERY

Read section titled “SAFETY, IMPORTANT SAFETY

INSTRUCTIONS FOR BATTERY CHARGER” (page 7).

You must charge the battery before use.

The charging method of battery is shown in page 15–17.

HOW TO OPERATE OPERATION

PANEL

Power indicator Power

switch

Nailing

operation switch

Nailing operation

indicator

Information indicator

(1) Power switch ON

Under the condition of “Power switch OFF”, push

and hold on Power switch more than 1 second, then

power indicator lights in Green.

NOTE

●

Do not press the push lever and/or pull the trigger

during the process of turning the power switch ON.

Doing so will prevent the power switch from turning

ON.

Light in green

OFF

ON

(2) Power switch OFF

Under the condition of “Power switch ON”, push

and hold on Power switch more than 1 second, then

power indicator goes oﬀ .

Under the condition of “Power switch ON”, functions

below are active.

19

English

(3) Select Nailing operation mode

(Full sequential actuation / Contact actuation)

After power switch turn ON, always set in Full

sequential actuation mode as initial. (Nailing

operation indicator light in blue.)

Light in blue

To change nailing operation mode, push Nailing

operation switch once. Every pushing, mode will

change between “Full sequential” and “Contact”.

Lighting (Blue):

FULL SEQUENTIAL ACTUATION MECHANISM,

Blinking (Blue):

CONTACT ACTUATION MECHANISM

Blink in blue

(4) Information indicator

In case of operation error, LED lamps show as below.

Status of indicator

1 LED (Red) blinks

The battery remaining

power is nearly empty.

Recharge the battery as

soon as possible.

2 LEDs (Red) blink

2 LED lights blink in an

interval.

•

In case of too hot

condition, Blink in

0.5 second interval.

•

In case of too cold

condition, Blink in

0.25 second interval.

After 10 seconds, LED

lights and Power switch

automatically turn oﬀ .

Machine is in too cold

(below 23°F (-5°C) or too

hot condition.

Allow the nailer to cool

or warm-up thoroughly in

adequate condition.

Status of indicator

2 LEDs blink in Orange,

after about 10 seconds,

automatically turn oﬀ

Power switch.

Contact metabo HPT for

inspection.

TESTING THE NAILER

DANGER

●

Operators and others in

work area MUST wear safety

glasses with side shields

which conforms to ANSI Z87.1

speciﬁ cations.

WARNING

●

Make sure the trigger is locked when not

ﬁ ring nails.

This Nailer has a lock mechanism to prevent the

nails from being ﬁ red.

Set the lock lever at the position to lock the

trigger.

Slide the lock lever to the position when the

Nailer is to be used, and to the position when it

is not in use.

Trigger

Lock lever Lock position

Free position

●

Never use Nailer unless push lever is operating

properly.

The machine employs a preventive mechanism

for unloaded operation.

The machine enters a state where the push lever

cannot be pushed up. This takes place when the

magazine is not loaded with nails or when the

remaining number of nails becomes less than 6.

20

English

CAUTION

●

Use caution not to throw the push lever tip onto

wood.

Before actually beginning the nailing work, test the Nailer

by using the checklist below. Conduct the tests in the

following order.

If abnormal operation occurs, stop using the Nailer

and contact a metabo HPT authorized service center

immediately.

(1) REMOVE ALL NAILS AND BATTERY FROM

NAILER.

□

ALL SCREWS MUST BE TIGHTENED.

□

THE PUSH LEVER AND TRIGGER MUST MOVE

SMOOTHLY with pulling back the feeder knob.

Trigger

Push lever Feeder knob

(2) Installing the battery.

Do not operate the push lever or trigger while

installing the battery.

Battery

Push

Pull out

Insert

Handle

Latch

(3) Turn on the Power switch.

Power indicator Power

switch

Nailing operation switch

Nailing operation

indicator

Turn on the Power switch by push and hold on Power

switch more than 1 second.

Make sure the power indicator is lighting in green,

and nailing operation indicator is lighting in blue.

(FULL SEQUENTIAL ACTUATION MECHANISM,)

NOTE

●

Do not press the push lever and/or pull the trigger

during the process of turning the power switch ON.

Doing so will prevent the power switch from turning ON.

Light in blueLight in green

[Auto power oﬀ ]

When the power is turned on but the Nailer is not

used for 30 minutes, the Nailer is automatically

turned oﬀ . To turn on again, press the power switch.

WARNING

Never leave the Nailer with the power on. This

could result in an accident.

Nailing operation indicator

Lighting (Blue):

FULL SEQUENTIAL ACTUATION MECHANISM,

Blinking (Blue):

CONTACT ACTUATION MECHANISM)

Make sure the battery indicator is not blinking. (page

27, Table 6)

If the battery indicator is blinking, the battery doesn’t

have enough power and it needs to be charged.

La page charge ...

Hikoki NR3675DD Manuel utilisateur

Hikoki NR3675DD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents