Hikoki D36DYA Manuel utilisateur

Marque: Hikoki

Modèle: D36DYA

Catégorie: Perceuses électriques

Taper: Manuel utilisateur

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual BEFORE operating the power tool. Please keep this manual available for other

users and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe

ser guardado en un lugar seguro.

Model

Modèle

Modelo D 36DYA

Cordless Angle Drill

Perceuse d’angle à batterie

Taladro angular inalámbrico

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges

and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

English

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or

storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power toolʼs operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

English

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 265 °F may

cause explosion.

g) Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range speciﬁ ed in the

instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service

providers.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Always wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

2. Use auxiliary handle(s).

Loss of control can cause personal injury.

3. Brace the tool properly before use.

This tool produces a high output torque and without

properly bracing the tool during operation, loss of

control may occur resulting in personal injury.

4. Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

Safety instructions when using long drill bits

5. Never operate at higher speed than the maximum

speed rating of the drill bit.

At higher speeds, the bit is likely to bend if allowed

to rotate freely without contacting the workpiece,

resulting in personal injury.

6. Always start drilling at low speed and with the bit

tip in contact with the workpiece.

At higher speeds, the bit is likely to bend if allowed

to rotate freely without contacting the workpiece,

resulting in personal injury.

7. Apply pressure only in direct line with the bit and

do not apply excessive pressure.

Bits can bend causing breakage or loss of control,

resulting in personal injury.

8. Make sure to securely hold the tool during

operation.

Failure to do so can result in accidents or injuries.

(Fig. 1)

Fig. 1

9. Never place hands or other body parts near the drill

bit or chuck during operation.

10. Do not use a side handle other than the one that is

included.

11. Install drill bits and accessories securely according to

the instruction manual.

12. Make sure that the area to be drilled is absolutely free

of any hidden obstructions including electrical wiring,

water, or gas pipes. Drilling into the aforementioned

may result in electric shock or short circuit, gas leak

or other hazards that can cause serious accidents or

injuries.

English

13. Because the cordless angle drill operates by battery

power, be aware of the fact that it can begin to operate

at any time.

14. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

15. Never touch moving parts.

Never place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

16. Never operate without all guards in place.

Never operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

17. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

18. Never use a power tool for applications other

than those speciﬁ ed.

Never use a power tool for applications other than

those speciﬁ ed in the instruction manual.

19. Handle tool correctly.

Operate the tool according to the instructions provided

herein. Do not drop or throw the tool. Never allow the

tool to be operated by children, individuals unfamiliar

with its operation or unauthorized personnel.

20. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

21. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

22. Accessories must be securely mounted to the

tool.

Prevent potential injuries to yourself or others.

Accessories which have been mounted to the tool

should be secure and tight.

23. Never use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

24. Do not use the protector for hanging the tool.

25. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

26. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

27. Always wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

28. NEVER wear gloves made from materials likely to roll

up such as cotton, wool, cloth or string, etc.

29. Do not touch metal parts of the tool body, bits, drills, or

swarf immediately after use, as these will be hot.

30. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

31. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

32. Always use the tool and battery at temperatures

between 23°F (-5°C) and 104°F (40°C).

33. Deﬁ nitions for symbols used on this tool

V ............ volts

—

---

......... direct current

no .......... no load speed

---/min .... revolutions or reciprocation per minute

English

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery types BSL18 series and multi

volt series. Other type of batteries may burst causing

personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating

Amperes* AWG Size of Cord

Equal to or

greater

than

but less

than

Length of Cord, Feet (Meter)

(7.5) 50

(15) 100

(30) 150

(45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can

use the power tool. Before using the model

UC18YSL3 battery charger, be sure to read all instructions

and cautionary statements on it, the battery and in this

manual.

CAUTION

USE ONLY metabo HPT BATTERIES. OTHER

MODELS OF BATTERIES MAY BURST AND

CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

English

WARNING

Improper use of the battery or battery charger

can lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or

is completely worn out. The battery can explode in a

ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery for a purpose other than those

speciﬁ ed.

5. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

6. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

7. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

8. Do not use in a location where strong static electricity

generates.

9. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

10. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible

and ﬂ ammable items. Corrosive gas atmospheres

must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

English

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 4).

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

Power Output

2 to 3 digit number

Fig. 2

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Angle Drill

Top handle Handle

Change leverDrill chuck

Motor

Front Cover

Battery

Name plate

LED light Chuck wrench

Trigger switch

Protector

Chuck wrench

holder

Side handle

Selector

switch

Housing

Fig. 3

2. Battery 3. Battery Charger

Display panel

Ventilation holes

Terminals

Battery cover

Latch

Ventilation

holes

Cord

Nameplate

Charge

indicator lamp

Guide rail

Fig. 4 Fig. 5

English

SPECIFICATIONS

1. Cordless Angle Drill

Model D36DYA

Motor DC Brushless motor

No-load speed Low 0–400 /min

High 0–1,500 /min

Capacity

Metal*1Twist bit 1/2 in. (13 mm)

Wood*1

Auger bit 2 in. (50 mm)

Self-feed bit 2-9/16 in. (65 mm)

Hole saw 6-1/4 in. (159 mm)

Drill chuck capacity

(Maximum gripping diameter) 1/2 in. (13 mm)

Battery*2

Model BSL36B18

Type Li-ion battery

Voltage DC 36 V / 18 V

Weight 13.9 lbs. (6.3 kg) (BSL36B18)

*1 Metal: Thickness 1/16 in. (1.6 mm)

Wood: Thickness 11/16 in. (18 mm)

*2 Existing batteries (BSL3660/3626/3620, BSL18 and BSL14 series, etc.) cannot be used with this tool. Use multi volt

type battery.

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL36B18 : Approx. 52 min

Charging voltage DC 14.4–18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

English

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (See Table 2)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Firmily insert the battery into the battery charger as

shown in Fig. 7.

Charge

indicator lamp

Guide rail

Battery

Fig. 7

3. Charging

When inserting a battery in the charger, charging will

commence and the charge indicator lamp will blink in

blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green. (See

Table 2)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 2, according to the condition of the

battery charger or the battery.

APPLICATIONS

○

Drilling holes in narrow spaces through which pipes

such as water pipes, gas pipes, and electrical

conduits are passed

○

Drilling large-diameter holes in wood

○

Drilling holes in metal

REMOVAL AND INSTALLATION METHOD

OF BATTERY

○

How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 6).

○

How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery (Fig. 6).

Battery

Push

Pull out

Insert

Handle

Latch

Fig. 6

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the

nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn out.

ASSEMBLY AND OPERATION

English

Table 2: Indications of the charge indicator lamp

ON/OFF at 0.5 sec. intervals

(RED) Before charging *1

Lights for 0.5 sec. at intervals

of 1 sec. (BLUE) Charged at less than

50%

Lights for 1 sec. at intervals of

0.5 sec. (BLUE) Charged at less than

80%

Lights continuously (BLUE) Charged at more than

80%

Lights continuously

(Continuous buzzer sound:

about 6 sec.) (GREEN) Charging complete

ON/OFF at 0.3 sec. intervals

(RED) Overheat standby *2

ON/OFF at 0.1 sec. intervals

(Intermittent buzzer sound;

about 2 sec.) (PURPLE) Charging impossible

NOTE

*1 If the red lamp continues to blink even after the

charger has been attached, check to conﬁ rm that the

battery has been fully inserted.

*2 Battery overheated. Unable to charge.

Although charging will start once the battery has

cooled down even when left in situ, the best practice

is to remove the battery and allow it to cool down in a

shaded, well-ventilated location before charging.

*3 Malfunction in the battery or the charger

–

Fully insert the battery.

–

Check to conﬁ rm that no foreign matter is stuck

to the battery mount or terminals. If there are no

foreign objects, it is probable that the battery

or charger is malfunctioning. Take it to your

authorized Service Center.

○

When the battery charger has been continuosly used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 5 minutes rest until the next charging.

(2) Regarding the temperature of the rechargeable

battery.

Table 3

Rechargeable

batteries Temperatures at which the battery

can be recharged

BSL36B18 32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4: Charging time

Charger

Battery UC18YSL3

BSL36B18 Approx. 52 min

NOTE

○

The recharging time may vary according to the

ambient temperature.

○

If charging takes a long time

– Charging will take longer at extremely low ambient

temperatures. Charge the battery in a warm

location (such as indoors).

– Do not block the air vent. Otherwise the interior will

overheat, reducing the charger’s performance.

– If the cooling fan is not operating, contact a

metabo HPT Authorized Service Center for

repairs.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery charger

after use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2–3 times.

English

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery (Fig. 8-a)

○

Charging a USB device from a electrical outlet

(Fig. 8-b)

○

Charging a USB device and battery from a

electrical outlet (Fig. 8-c)

abc

Fig. 8

(2) Turn the USB power switch ON (Fig. 9)

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power

switch

USB power

indicator lamp

Rubber cover

USB port

USB cable

Fig. 9

(3) Connect the USB cable. (Fig. 9)

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

○

When the power cord is not plugged into an outlet and

the battery runs out of power, power output will stop

and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out, change

the battery or plug the power cord into an electrical

outlet.

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the power

cord from the electrical outlet. (Fig. 9)

○

Remove the battery from the charger and place the

rubber cover over the USB port.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

HOW TO RECHARGE USB DEVICE

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

English

○

Charging stops for approximately ﬁ ve seconds to

allow the power supply to be detected under the

following conditions: if the battery charger power plug

is plugged in while charging a USB device from the

battery, or if a rechargeable battery is inserted while

charging a USB device from the battery charger.

○

USB charging stops for ﬁ ve seconds so that checking

can be performed once the rechargeable battery has

been fully charged.

○

If the rechargeable battery level is extremely low,

charging the rechargeable battery takes priority, and

USB charging is temporarily stopped. USB charging

automatically resumes once the battery level has

reached a preset level.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

OPERATION

WARNING

To avoid serious accident, ensure the switch is in

the OFF position, and pull out the battery.

1. Mounting and dismounting of the bit.

(1) Open the chuck jaws, and insert the bit into the chuck.

(2) Place the chuck wrench in each of the three holes

in the chuck, and turn it in the clockwise direction

(viewed from the front side). Fasten the drill chuck

ﬁ rmly by evenly tightening with each of its 3 holes a

little at a time.

Self-feed bit Tighten

Chuck Wrench

Loosen

Fig. 10

To remove the bit, place the chuck wrench into one of

the holes in the chuck and turn it in the counterclockwise

direction.

2. Chuck wrench storage

The chuck wrench can be stored in the tool body.

(Fig. 11)

Chuck Wrench

Chuck Wrench holder

Fig. 11

3. Installing the side handle.

Screw the side handle into the front cover tightly.

(Fig. 12)

The side handle can be installed on either side.

Tighten

Side handle Loosen

Loosen

Tighten

Fig. 12

4. Check the rotational direction.

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector switch.

The L-side of the selector switch is pushed to turn the

bit counterclockwise (See Fig. 13). (The and

marks are provided on the body.)

English

Handle

Selector switch

Fig. 13

CAUTION

When the selector switch is in the center position,

the trigger switch cannot be pulled. Always

set the selector switch to the center position

or remove the battery pack before performing

maintenance, changing accessories, storing the

tool and any time the tool is not in use.

5. Change rotation speed.

Change lever

Push-button

Low speed

High speed

Fig. 14

Change the rotational speed by turning the change

lever while pressing the push-button. Set the ▲ mark

position of the change lever to that of the rotation

speed to be used. (See Fig. 14)

When the change lever is set to “1”, the drill rotates at

a low speed. When set to “2”, the drill rotates at a high

speed.

CAUTION

●

When changing the rotational speed with the

change lever, conﬁ rm that the switch is oﬀ .

Changing the speed while the motor is rotating

will damage the gears.

●

When a large force is required for operation set

the change lever to “1”. If “2” is set and the unit

is used, it may cause the motor to burn out or

malfunction prematurely.

●

To operate the change lever, press the push

button, and release the lock of the change lever.

Also, check and make sure after operation

that the push button has returned and that the

change lever has been locked.

●

Switch the change lever without mistake.

If it is used at a position halfway, there is a fear

that the service life of the switching mechanism

may be shortened.

6. Conﬁ rm that the battery is mounted correctly.

CAUTION

Until the battery locks in place with a little click,

if not, it may accidentally fall out of the tool

causing injury to you or someone around you.

7. Switch operation

○

When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

When releasing the trigger of the switch, the brake will

be applied for immediate stopping.

○

The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

CAUTION

●

The motor rotation may be locked to cease while

the unit is used as drill. While operating the angle

drill, take care not to lock the motor.

●

If the motor is locked, immediately turn the power

oﬀ . If the motor is locked for a while, the motor or

battery may be burnt.

●

A buzzing noise is produced when the motor

is about to rotate; This is only a noise, not a

machine failure.

CAUTION

●

Do not apply excessive force during operation.

Doing so will not only damage the tip of the drill

bit, but also reduce the service life of the power

tool.

●

When drilling holes with a hole saw, the larger

the diameter is, the larger the reactive force

applied to your arm becomes.

To prevent loss of control from the reactive

force, ensure that you have ﬁ rm footing, support

the tool ﬁ rmly with both hands, and drill holes

perpendicular to the drilled material.

Pressing with excessive force or prying can

cause loss of control from the reactive force,

which may damage the blade tip of the hole saw

or result in injury. Additionally, doing so makes

the tool more likely to be stopped by the overload

protection.

English

●

Drill bits may snap oﬀ while withdrawing from

the drilled hole. When withdrawing, relax the

force with which you press the tool against the

material.

8. How to use the LED light

While the switch is pulled, the LED light will

automatically light up the tip portion of the tool.

(Fig. 15)

The LED light will automatically turn oﬀ 10 seconds

after the switch is released.

The LED light also functions as a warning signal that

lights up during use.

For details, see “10. LED light warning signals”.

Trigger switch

LED light

Fig. 15

CAUTION

●

Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

●

Wipe oﬀ any dirt or grime attached to the lens of

the LED light with a soft cloth, being careful not

to scratch the lens.

Scratches on the lens of the LED light can result

in decreased brightness.

9. Reactive force control

This product is equipped with a Reactive Force

Control (RFC) feature that reduces jerking of the tool

body.

If the tool bit is suddenly overburdened, any jerking of

the tool body is reduced by activation of the slip clutch

or by stopping of the motor by the sensor built into the

tool body.

If the motor is stopped because of overburdening

detection by the controller, the LED light will blink

while the switch is pulled. The motor will remain

stopped while the lamp is blinking. (Fig. 16)

NOTE

●

RFC may not always activate under certain working

conditions or situations.

When working, ensure that the material is securely

placed and fastened, hold the tool body securely, and

be suﬃ ciently careful not to suddenly apply a large

load to the tool tip.

●

Take care to hold the tool ﬁ rmly to prevent any jerking

motion.

●

Possible causes of sudden overburdening

Tool bit biting into material

Impact against nails, metal or other hard objects

Tasks involving prying or any excess application of

pressure, etc.

Also, other causes include any combination of the

aforementioned.

●

When the reactive force control (RFC) is triggered

When the RFC is triggered and the motor stops, turn

oﬀ the tool’s switch and remove the cause of the

overburdening before continuing operation.

Fig. 16

10. LED light warning signals

This product features functions that are designed to

protect the tool itself as well as the battery. If any of

the safeguard functions activate during operation, the

LED light will blink as described in Table 5. When any

of the safeguard functions are triggered, immediately

remove your ﬁ nger from the switch and follow the

instructions described under corrective action.

English

Table 5

LED Light Display Safeguard Function

On 0.1 second/

oﬀ 0.5 second

Blinks for

approximately

3 seconds after the

switch has been

released.

Overburden Protection

If the operating with the change

lever set on “2”, adjust to “1” and

continue operation.

Remove the cause of the

overburdening.

RFC

Remove the problem causing the

tool to jerk excessively.

When operating the tool, ﬁ rmly

hold the tool to make sure it

doesn't jerk.

On 0.5 second/Oﬀ

0.5 second

Blinks while

protection is in

eﬀ ect.

Temperature Protection

Allow the tool and battery to

thoroughly cool.

11. Remaining battery indicator

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light

the indicator lamp. (Fig. 17, Table 6)

It is best to use the remaining battery indicator as

a guide since there are slight diﬀ erences such as

ambient temperature and the condition of the battery.

Also, the remaining battery indicator may vary from

those equipped to a tool or charger.

Display panel

Remaining battery

indicator lamp Remaining battery

indicator switch

Fig. 17

Table 6

Lights ;

The battery remaining power is over 75%.

Lights ;

The battery remaining power is 50%–75%

Lights ;

The battery remaining power is 25%–50%

Lights ;

The battery remaining power is less than

25%.

Blinks ;

The battery remaining power is nearly empty.

Recharge the battery soonest possible

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow it

to fully cool down.

Blinks ;

Output suspended due to failure or

malfunction. The problem may be the battery

so please contact your dealer.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and

battery characteristics, read it as a reference.

NOTE

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

HOW TO USE

WARNING

●

To prevent accidents, make sure to turn the

switch oﬀ and disconnect the battery when the

drill bits and other various parts are installed

or removed. The power switch should also be

turned oﬀ during a work break and after work.

CAUTION

●

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.

English

1. Fixing the body in place

○

If a load is applied to the bit when drilling holes, the

tool may be pushed out of control in the opposite

direction by recoil.

To reduce the load applied to the bit, use a well-

sharpened bit that is appropriate for the type of work.

Place the bit straight against the surface to be drilled.

○

Try to avoid drilling holes in wood that is bent, damp,

or has many knots. Also, ensure that there are no nails

or other metal objects inside the wood.

○

When drilling existing holes to make them larger, or

when the bit goes all the way through the material, be

careful as a load may be applied to the bit.

○

Placing the side handle against a pillar, etc. while

working can prevent the tool body from jerking out of

control. (Fig. 18)

Side handle

Recoil direction

Rotation direction

(When rotating forward)

Side handle

Recoil direction

Rotation direction

(When rotating in reverse)

Fig. 18

2. Slip clutch

During work, the slip clutch activates when a

large load is suddenly applied, which causes the

transmission between the motor and the bit to slip,

and the bit rotation stops. If this feature activates and

the drill rotation stops, quickly stop the switch.

NOTE

The slip clutch only activates when the change lever is

in low speed (“1”).

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous drilling or tightening wood screw work may

cause the temperature of the unit to rise, activating

the temperature protection circuit and automatically

stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous tightening wood screw works,

rest the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

English

MAINTENANCE AND INSPECTION

WARNING

Pull out battery before doing any inspection or maintenance.

1. Checking the condition of the bit

The bits should be checked regularly. If worn or

broken bits can slip or decrease the eﬃ ciency of the

motor and burn it out.

Replace worn bits with new ones.

CAUTION

If you use a driver bit of which point is worn or

broken, it will be dangerous since it slips. So

replace it with a new one.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them

and make sure they are tight.

CAUTION

Using this power tool with loosened, screws is

extremely dangerous.

3. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have

collected on the terminals.

Failure to do so may result in malfunction.

4. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for

they may damage the plastics.

5. Disposal of the exhausted battery

WARNING

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable.

At the end of it’s useful life, under various state

and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste oﬃ cials for details

in your area for recycling options or proper

disposal.

6. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

7. Storage

Store the power tool and battery in a place in which

the temperature is less than 104°F (40°C) and out of

reach of children.

NOTE

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time

may be recovered by repeatedly charging and using

the batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

8. Service and repairs

All quality power tools will eventually require servicing

or replacement of parts because of wear from normal

use. To assure that only authorized replacement parts

will be used, all service and repairs must be performed

by a metabo HPT AUTHORIZED SERVICE CENTER,

ONLY.

CAUTION

In the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

Important notice on the batteries for the

metabo HPT cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

English

ACCESSORIES

WARNING

ALWAYS use Only authorized metabo HPT replacement parts and accessories. NEVER use replacement

parts or accessories which are not intended for use with this tool. Contact metabo HPT if you are not sure

whether it is safe to use a particular replacement part or accessory with your tool.

The use of any other attachment or accessory can be dangerous and could cause injury or mechanical

damage.

NOTE

Accessories are subject to change without any obligation on the part of the metabo HPT.

STANDARD ACCESSORIES

D36DYA

(WCZ)

Side Handle (Code No. 380501) ........................................................... 1

Battery (BSL36B18) .............................................................................. 1

Battery Charger (UC18YSL3) ................................................................ 1

Bag (Code No. 380502M) ..................................................................... 1

Battery cover (Code No. 329897) ......................................................... 1

D36DYA

(NN)

Side Handle (Code No. 380501) ........................................................... 1

OPTIONAL ACCESSORIES.....sold separately

○

Battery (BSL36B18)

NOTE

Speciﬁ cations are subject to change without any obligation on the part of the metabo HPT.

English

La page charge ...

Hikoki D36DYA Manuel utilisateur

Marque: Hikoki

Modèle: D36DYA

Catégorie: Perceuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hikoki D36DYA User manual
español: Hikoki D36DYA Manual de usuario

Hikoki D36DYA Manuel utilisateur

Hikoki D36DYA Manuel utilisateur

dans d''autres langues

Documents connexes