Hikoki DV36DC Manuel utilisateur

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual before operating the power tool. Please keep this manual available for other users

and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil

motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe

ser guardado en un lugar seguro.

Model

Modèle

Modelo

DS 18DC

DV 18DC • DV 36DC

Cordless Driver Drill

Perceuse-visseuse sans ﬁ l

Taladro atornillador inalámbrico

Cordless Hammer Drill

Perceuse à percussion sans ﬁ l

Taladro de percusión inalámbrico

DS18DC DV18DC / DV36DC

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges

and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

2

English

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or

storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power toolʼs operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

3

English

Cutting accessory or fasteners contacting a “live” wire

may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

Safety instructions when using long drill bits

5. Never operate at higher speed than the maximum

speed rating of the drill bit.

At higher speeds, the bit is likely to bend if allowed

to rotate freely without contacting the workpiece,

resulting in personal injury.

6. Always start drilling at low speed and with the bit

tip in contact with the workpiece.

At higher speeds, the bit is likely to bend if allowed

to rotate freely without contacting the workpiece,

resulting in personal injury.

7. Apply pressure only in direct line with the bit and

do not apply excessive pressure.

Bits can bend causing breakage or loss of control,

resulting in personal injury.

8. Make sure to securely hold the tool during

operation.

Failure to do so can result in accidents or injuries.

(Fig. 1)

Fig. 1

9. Never place hands or other body parts near the drill

bit or chuck during operation. Hold the drill by its

handle only.

10. Because the cordless tool operates by battery power,

be aware of the fact that it can begin to operate at any

time.

11. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

12. Never touch moving parts.

Never place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

13. Never operate without all guards in place.

Never operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 265 °F may

cause explosion.

g) Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range speciﬁ ed in the

instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service

providers.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Wear ear protectors with impact drilling.

Exposure to noise can cause hearing

loss.

2. Use auxiliary handle(s).

Loss of control can cause personal injury.

3. Brace the tool properly before use.

This tool produces a high output torque and without

properly bracing the tool during operation, loss of

control may occur resulting in personal injury.

4. Hold the power tool by insulated gripping

surfaces, when performing an operation where

the cutting accessory or fasteners may contact

hidden wiring.

4

English

14. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

15. Never use a power tool for applications other

than those speciﬁ ed.

Never use a power tool for applications other than

those speciﬁ ed in the instruction manual.

16. Handle tool correctly.

Operate the tool according to the instructions provided

herein. Do not drop or throw the tool. Never allow the

tool to be operated by children, individuals unfamiliar

with its operation or unauthorized personnel.

17. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

18. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

19. Accessories must be securely mounted to the

tool.

Prevent potential injuries to yourself or others.

Accessories which have been mounted to the tool

should be secure and tight.

20. Never use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

21. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

22. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

23. Always wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

24. Do not touch metal parts of the tool body, bits, drills, or

swarf immediately after use, as these will be hot.

25. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

26. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

27. Always use the tool and battery at temperatures

between 23°F (-5°C) and 104°F (40°C).

28. Deﬁ nitions for symbols used on this tool

V ............ volts

—

---

......... direct current

no .......... no load speed

---/min .... revolutions or reciprocation per minute

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery types BSL18 series and multi

volt series. Other type of batteries may burst causing

personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

5

English

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YSL3 battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

CAUTION

USE ONLY metabo HPT BATTERIES. OTHER

MODELS OF BATTERIES MAY BURST AND

CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery

or battery charger can lead to

serious injury. To avoid these

injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or

is completely worn out. The battery can explode in a

ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use DC power to charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

6

English

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery for a purpose other than those

speciﬁ ed.

5. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

6. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

7. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

8. Do not use in a location where strong static electricity

generates.

9. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

10. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible

and ﬂ ammable items. Corrosive gas atmospheres

must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 4).

7

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

Wh

Power Output

2 to 3 digit number

Fig. 2

8

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Driver Drill / Cordless Hammer Drill

Housing

Motor

Gear case

Clutch dial

Keyless chuck

Shift knob

Side handle

Push button

Ventilation holes

Trigger switch

Battery

Ventilation holes

Hook

Handle

Name plate

LED Light

Fig. 3

2. Battery 3. Battery Charger

Battery

Ventilation holes

Terminals

Battery cover

Latch

Ventilation

holes

Body

Cord

Nameplate

Charge

indicator lamp

Guide rail

Fig. 4 Fig. 5

9

English

SPECIFICATIONS

1. Cordless Driver Drill / Cordless Hammer Drill

Model DS18DC DV18DC DV36DC

Motor DC Brushless motor

No-load

speed

Low 0–500 /min 0–550 /min

High 0–2,000 /min 0–2,200 /min

No-load

impact rate

Low 0–7,500 /min 0–8,250 /min

High 0–30,000 /min 0–33,000 /min

Capacity

Drilling

Brick *1 ————— 3/4 in. (20 mm) 7/8 in. (22 mm)

Wood *1

(Soft Wood) 4 in. (102 mm) 4-5/8 in. (118 mm)

Metal *1

(Mild Steel) 5/8 in. (16 mm) 3/4 in. (20 mm)

Screw Driver Wood screw 7/16 in. × 4 in.

(12 mm × 100 mm) 5/8 in. × 4 in.

(16 mm × 100 mm)

Small screw 1/4 in. (6 mm)

Drill chuck capacity Maximum gripping diameter 1/2 in. (13 mm)

Battery

Model BSL36A18X

Type Li-ion battery

Voltage DC 36 V / 18 V

Weight 6.2 lbs. (2.8 kg) (BSL36A18X and side handle attached)

*1 Brick: Depth 1-1/4 in. (30 mm)

Wood: Thickness 1-1/2 in. (38 mm)

Metal: Thickness 1/16 in. (1.6 mm)

DV36DC only: Existing batteries (BSL3660/3626/3620, BSL18xx and BSL14xx series, etc.) cannot be used with this

tool. Use multi volt type battery.

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL36A18X : Approx. 32 min

Charging voltage DC 14.4–18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

10

English

ASSEMBLY AND OPERATION

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s pilot

lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in

Fig. 7.

Charge

indicator lamp

Guide rail

Battery

Fig. 7

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green. (See

Table 2)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 2, according to the condition of the

battery charger or the battery.

APPLICATIONS

○

Use as a hammer drill

Drilling of soft bricks and concrete blocks.

○

Use as a drill

Drilling of soft steel, wood, plastic and aluminum

materials.

○

Use as a screwdriver

Tightening and loosening of machine screws, wood

screws and tapping screws.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

○

How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 6).

○

How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery (Fig. 6).

Battery

Push

Pull out Insert

Handle

Latch

Fig. 6

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

11

English

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3

Rechargeable

batteries Temperatures at which the battery

can be recharged

BSL36A18X 32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery UC18YSL3

BSL36A18X Approx. 32 min

NOTE

The recharging time may vary according to the

ambient temperature.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery charger

after use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2–3 times.

Table 2

Charger

status Status of indicator

lamp Indication meaning

Before

charging

ON/OFF at 0.5 sec.

intervals (RED) Plugged into power

source *1

While

charging

Lights for 0.5 sec.

at intervals of 1 sec.

(BLUE) Charged at less

than 50%

Lights for 1 sec. at

intervals of 0.5 sec.

(BLUE) Charged at less

than 80%

Lights continuously

(BLUE) Charged at more

than 80%

Charging

complete

Lights continuously

(GREEN)

(Continuous buzzer

sound: about 6 sec.)

Overheat

standby

ON/OFF at 0.3 sec.

intervals (RED) Battery overheated.

Unable to charge. *2

Charging

impossible

ON/OFF at 0.1 sec.

intervals (PURPLE)

(Intermittent buzzer

sound; about 2 sec.)

Malfunction in

the battery or the

charger *3

*1 If the red lamp continues to blink even after the

charger has been attached, check to conﬁ rm that the

battery has been fully inserted.

*2 Although charging will start once the battery has

cooled down even when left in situ, the best practice

is to remove the battery and allow it to cool down in a

shaded, well-ventilated location before charging.

*3

○ Fully insert the battery.

○ Check to conﬁ rm that no foreign matter is stuck to the

battery mount or terminals.

○ Charging will take longer at extremely low ambient

temperatures. Charge the battery in a warm location

(such as indoors).

○ Do not block the air vent. Otherwise the interior will

overheat, reducing the charger’s performance.

○ If the cooling fan is not operating, contact a

metabo HPT Authorized Service Center for repairs.

12

English

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery (Fig. 8-a)

○

Charging a USB device from a electrical outlet

(Fig. 8-b)

○

Charging a USB device and battery from a

electrical outlet (Fig. 8-c)

abc

Fig. 8

(2) Turn the USB power switch ON (Fig. 9)

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power

switch

USB power

indicator lamp

Rubber cover

USB port

USB cable

Fig. 9

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated because

it has been left for a long time in a location

subject to direct sunlight or because the battery

has just been used, the charge indicator lamp of

UC18YSL3 charger lights for 0.3 seconds, does

not light for 0.3 seconds (oﬀ for 0.3 seconds). In

such a case, ﬁ rst let the battery cool, then start

charging.

●

When the charge indicator lamp ﬂ ickers (at

0.2–second intervals), check for and take out

any foreign objects in the charger’s battery

installation hole. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

HOW TO RECHARGE USB DEVICE

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

13

English

(3) Connect the USB cable. (Fig. 9)

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

○

When the power cord is not plugged into an outlet and

the battery runs out of power, power output will stop

and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out, change

the battery or plug the power cord into an electrical

outlet.

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the power

cord from the electrical outlet. (Fig. 9)

○

Remove the battery from the charger and place the

rubber cover over the USB port.

○

Charging stops for approximately ﬁ ve seconds to

allow the power supply to be detected under the

following conditions: if the battery charger power plug

is plugged in while charging a USB device from the

battery, or if a rechargeable battery is inserted while

charging a USB device from the battery charger.

○

USB charging stops for ﬁ ve seconds so that checking

can be performed once the rechargeable battery has

been fully charged.

○

If the rechargeable battery level is extremely low,

charging the rechargeable battery takes priority, and

USB charging is temporarily stopped. USB charging

automatically resumes once the battery level has

reached a preset level.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

OPERATION

WARNING

Make sure to securely hold the tool during

operation. Failure to do so can result in accidents

or injuries.

1. Mounting and dismounting of the bit.

(1) Mounting the bit.

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front)

to open the clip on the keyless chuck. After inserting

a driver bit, etc., into the keyless drill chuck, and

tighten the sleeve by turning it toward the right (in the

clockwise direction as viewed from the front). (See

Fig. 10).

Tighten

Loosen Sleeve

Fig. 10

NOTE

If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front),

and then take out the bit etc. (See Fig. 10)

NOTE

○

If the sleeve is tightened in a state where the clip of the

keyless chuck is opened to a maximum limit, a click

noise may occur. This is the noise that occurs when

the loosening of the keyless chuck is prevented and is

not a malfunction.

○

When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit. Set

the clutch mode between 1 and 11 and then turn the

sleeve to the loose side (left side) while operating the

clutch. It should be easy now to loosen the sleeve.

2. Installing/Removing the side handle. (Fig. 11)

WARNING

When using the tool, make sure the side handle

is attached and ﬁ rmly secured.

If not ﬁ rmly secured, the tool may jerk out of

position when overburdened, resulting in injury.

(1) Turn the grip of the side handle to loosen it and push it

in until it comes in contact with the clutch dial.

(2) Adjust the side handle to the angle that allows the

easiest use, then turn the side handle’s grip ﬁ rmly to

lock it place.

Loosen

Clutch

dial

Side

handle

Tighten

Fig. 11

14

English

3. Conﬁ rm that the battery is mounted correctly.

4. Check the rotational direction.

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise (See Fig. 12).

(The

and marks are provided on the body.)

Push button

Forward Reverse

Fig. 12

CAUTION

The push button can not be switched while the

power tool is turning. To switch the push button,

stop the power tool, then set the push button.

5. Change rotation speed.

Shift knob

Low speed

“1”

Fig. 13

Shift knob

High speed

“2”

Fig. 14

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (See

Figs. 13 and 14).

When the shift knob is set to “1”, the drill rotates at a

low speed. When set to “2”, the drill rotates at a high

speed.

CAUTION

●

When changing the rotational speed with the

shift knob, conﬁ rm that the switch is oﬀ .

Changing the speed while the motor is rotating

will damage the gears.

●

When a large force is required for operation

(operations indicated in the following chart) set

the shift knob to “1”. If “2” is set and the unit

is used, it may cause the motor to burn out or

malfunction prematurely.

6. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown in

Table 5.

Table 5

Work Cap position Suggestions

Drilling

Brick

(DV18DC / DV36DC) Use for drilling purpose.

Wood

Use for drilling purpose.Steel

Aluminum

Screw tightening

Small screw 1 – 22 Use the bit and socket matching the screw diameter.

Wood screw 1 – Use after drilling a pilot hole.

15

English

7. Conﬁ rm the clutch dial position.

<DS18DC> (Fig. 15)

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the

clutch dial is set.

Clutch dial

Triangle mark

Strong

Weak

mark

Fig. 15

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 4, 7 ... 22” on the clutch dial, or the

dot, with the triangle mark on the outer body.

(2) When using this unit as a drill, line up the clutch dial

drill mark “ ” with the triangle mark on the outer

body.

CAUTION

●

The clutch dial cannot be set between the

numbers “1, 4, 7 ... 22” or the dot.

●

Do not use with the clutch dial set at the line

between the number “22” and the drill mark

“”. Doing so may cause damage (See Fig. 16).

Line

Triangle mark

mark

Fig. 16

<DV18DC / DV36DC> (Fig. 17)

The three modes of screwdriver, drill and hammer drill

can be switched by the position of the clutch dial in

this unit.

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 4, 7 ... 22” on the clutch dial, or the

dot, with the triangle mark on the outer body.

(2) When using this unit as a drill, line up the clutch dial

drill mark “ ” with the triangle mark on the outer

body.

(3) When using this unit as a hammer drill, align the clutch

dial hammer mark “ ” with the triangle mark on the

outer body.

mark

Triangle mark

mark

Clutch dial

Weak

Strong

Fig. 17

CAUTION

●

The clutch dial cannot be set between the

number “1, 4, 7 ... 22” or the dot.

●

Do not use with the clutch dial number at “22”

and the line at the middle of the drill mark. Doing

so may cause damage. (See Fig. 18)

Line

mark Triangle mark

mark

Fig. 18

16

English

8. Rotation to Hammer changeover (DV18DC / DV36DC)

The “Rotation (Rotation only)” and “Hammer (Hammer

+ Rotation)” can be switched by aligning the drill mark

“” or the hammer mark “ ” with the triangle mark

on the outer body.

○

To make holes in the metal, wood or plastic, switch to

“Rotation (Rotation only)”.

○

To make holes in the bricks or concrete blocks, switch

to “Hammer (Hammer + Rotation)”.

CAUTION

Do not use the Cordless hammer drill in the

“Hammer” setting if the material can be bored

by rotation only. Such action will not only reduce

drill eﬃ ciency, but may also damage the drill tip.

9. Tightening torque adjustment.

(1) Tightening torque

Tightening torque should correspond in its intensity to

the screw diameter. When too strong power is used,

the screw head may be broken or be injured.

Be sure to adjust the clutch dial position according to

the screw diameter.

Refer to Table 6 for the clutch dial position tightening

torques.

(2) Tightening torque indication (See Fig. 15, 17)

The tightening torque diﬀ ers depending on the type of

screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 4, 7 ... 22” on the clutch dial, and a dot.

The tightening torque at position “1” is the weakest

and the torque is strongest at the highest number.

(3) Adjusting the tightening torque (See Fig. 15, 17)

Rotate the clutch dial and line up the numbers “1, 4, 7, ...

22” on the clutch dial, or the dot, with the triangle mark on

the outer body. Adjust the clutch dial in the weak or the

strong torque direction according to the torque you need.

Table 6 Tightening torque

Clutch dial

position Tightening torque

1 Approximately 13 in.-lbs. (15 kg-cm)

4 Approximately 21 in.-lbs. (29 kg-cm)

7 Approximately 30 in.-lbs. (34 kg-cm)

10 Approximately 38 in.-lbs. (44 kg-cm)

13 Approximately 46 in.-lbs. (53 kg-cm)

16 Approximately 54 in.-lbs. (63 kg-cm)

19 Approximately 63 in.-lbs. (72 kg-cm)

22 Approximately 71 in.-lbs. (82 kg-cm)

10. Switch operation

○

When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

When releasing the trigger of the switch, the brake will

be applied for immediate stopping.

○

The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

CAUTION

●

The motor rotation may be locked to cease while

the unit is used as drill. While operating the

driver drill, take care not to lock the motor.

●

If the motor is locked, immediately turn the power

oﬀ . If the motor is locked for a while, the motor or

battery may be burnt.

11. For drilling into brick (DV18DC / DV36DC)

Excessive pressing force never increases drilling

speed. It will not only damage the drill tip or reduce

working eﬃ ciency, but could also shorten the service

life of drill bit. Operate the hammer drill within 10-20 kg

pressing force while drilling into brick.

12. How to select rotational speed

CAUTION

●

The selection examples shown in Table 7 should

be considered as general standard. As diﬀ erent

types of tightening screws and diﬀ erent materials

to be tightened are used in actual works proper

adjustments are naturally necessary.

●

When using the driver drill/hammer drill with a

machine screw at 2 (high speed), a screw may

damage or a bit may loose due to the tightning

torque is too strong. Use the driver drill/hammer

drill at 1 (low speed) when using a machine

screw.

NOTE

The use of the battery in a cold condition (below

0 degree Centigrade) can sometimes result in the

weakened tightening torque and reduced amount of

work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

17

English

13. Remaining battery indicator

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light

the indicator lamp. (Fig. 19, Table 8)

The indicator will shut oﬀ approximately 3 seconds

after the remaining battery indicator switch is pressed.

It is best to use the remaining battery indicator as

a guide since there are slight diﬀ erences such as

ambient temperature and the condition of the battery.

Also, the remaining battery indicator may vary from

those equipped to a tool or charger.

Table 8

State of lamp Battery Remaining Power

Lights ;

The battery remaining power is

over 75%.

Lights ;

The battery remaining power is

50%–75%.

Lights ;

The battery remaining power is

25%–50%.

Lights ;

The battery remaining power is

less than 25%.

Blinks ;

The battery remaining power

is nearly empty. Recharge the

battery soonest possible

Blinks ;

Output suspended due to high

temperature. Remove the

battery from the tool and allow it

to fully cool down.

Blinks ;

Output suspended due to failure

or malfunction. The problem

may be the battery so please

contact your dealer.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and

battery characteristics, read it as a reference.

Display panel

Remaining battery

indicator lamp Remaining battery

indicator switch

Fig. 19

NOTE

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

14. How to use the LED light

While the switch is pulled, the LED light will

automatically light up the tip portion of the tool.

(Fig. 20)

The LED light will automatically turn oﬀ 10 seconds

after the switch is released.

The LED light also functions as a warning signal that

lights up during use.

For details, see “17. LED light warning signals”.

Table 7

Work Cap

Position

Rotating speed selection (Position of the shift knob)

1 (Low speed) 2 (High speed)

Screw

tightening

Wood screw

1 –

For 7/16 in. (12 mm) or smaller

diameter screws. For 1/4 in. (6 mm) or smaller

diameter screws.

(DS18DC / DV18DC)

(DV36DC) For 5/8 in. (16 mm) or smaller

nominal diameter screws. For 5/16 in. (8 mm) or smaller

nominal diameter screws.

Drilling

Wood For 4 in. (102 mm) or smaller

diameters. For 1-1/2 in. (38 mm) or smaller

diameters.

(DS18DC / DV18DC)

(DV36DC) For 4-5/8 in. (118 mm) or

smaller diameters. For 2-1/8 in. (54 mm) or smaller

diameters.

18

English

Trigger switch

Fig. 20

CAUTION

●

Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

●

Wipe oﬀ any dirt or grime attached to the lens of

the LED light with a soft cloth, being careful not

to scratch the lens.

Scratches on the lens of the LED light can result

in decreased brightness.

15. Using the hook

The hook is used to hang up the power tool to your

waist belt while working.

CAUTION

●

When using the hook, hang up the power tool

ﬁ rmly not to drop accidentally.

If the power tool is dropped, it may lead to an

accident.

●

When electing to carry the tool hooked to your

hip belt, make sure to detach the tool bit and side

handle.

Failure to do so may result in unexpected injury.

●

Install securely the hook. Unless the hook is

securely installed, it may cause an injury while

using.

(1) Mounting the hook

Install securely the hook in the groove of power tool

and tighten the screw to ﬁ x the hook ﬁ rmly. (Fig. 21)

Hook

Screw

Groove

Fig. 21

(2) Removing the hook

Loosen the screw ﬁ xing the hook with Philips screw

driver. (Fig. 22)

Screw

Hook

Groove

Fig. 22

16. RFC (Reactive force control)

This product features RFC.

This stops the motor automatically if the tool is jerking

excessively.

The LED light ﬂ ashes to indicate that RFC has been

activated.

If this occurs, release your ﬁ nger from the switch

before restarting. (Fig. 23)

NOTE

●

RFC may not always activate under certain working

conditions or situations.

●

Take care to hold the tool ﬁ rmly to prevent any jerking

motion.

●

RFC may also activate if you change position

suddenly while holding the tool.

Fig. 23

19

English

17. LED light warning signals

This product features functions that are designed

to protect the tool itself as well as the battery. While

the switch is pulled, if any of the safeguard functions

activate during operation, the LED light will blink as

described in Table 9. When any of the safeguard

functions are triggered, immediately remove your

ﬁ nger from the switch and follow the instructions

described under corrective action.

Table 9

Safeguard

Function LED Light Display Corrective Action

Overburden

Protection

On 0.1 second/oﬀ

0.1 second

(rapid blinking)

Blinks for

approximately

3 seconds after the

switch has been

released.

If the operating

with the shift knob

set on “2”, adjust

to “1” and continue

operation.

Remove the

cause of the

overburdening.

RFC

On 0.15 second/oﬀ

0.15 second ×

3 times/Oﬀ

2 seconds

Blinks for

approximately

3 seconds after the

switch has been

released.

Remove the

problem causing

the tool to jerk

excessively.

When operating

the tool, ﬁ rmly hold

the tool to make

sure it doesn't jerk.

Temperature

Protection

On 0.5 second/

Oﬀ 0.5 second

(slow blinking)

Blinks while

protection is in

eﬀ ect.

Allow the tool

and battery to

thoroughly cool.

18. Using depth gauge (sold separately) (Fig. 24)

(1) Insert the depth gauge through the side handle’s

mounting hole.

(2) Adjust the length to the hole depth, then clamp in

place using the M5 thumb screw.

Side handle’s

mounting hole

M5 thumb screw

Depth gauge

Tighten

Fig. 24

OPERATIONAL CAUTIONS

Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous bolt-tightening work may cause the

temperature of the unit to rise, activating the

temperature protection circuit and automatically

stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous tightening wood screw works,

rest the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

20

English

La page charge ...

Hikoki DV36DC Manuel utilisateur

Ce manuel convient également à

Hikoki DV36DC Manuel utilisateur

dans d''autres langues

Documents connexes