Address：16-3,Shunping 1st St.,Xitun Dist., Taichung City 40754, Taiwan (R.O.C)
Tel：886-4-2295-0350 Fax：886-4-2295-0357
MANUAL
使用手冊
CUSTOMER
Item P/N CS61006
DESCRIPTION Audio Driver Board with BT Module
Document Number CS61006
DATE
This document contains confidential and proprietary information of CORESTARCo., Ltd and shall not be duplicated
or otherwise transferred to a third party without the express written consent of CORESTAR.
本文件所包含內容所屬於合興數位股份有限公司(CorsStar Co., Ltd)之規格文件及專有技術資料所有，不得未經由合興
數位公司同意而擅自轉載或以不明確的書面或其他方式轉讓給第三方。
page 2 / 6
1. Hardware overview
1.1 Main Board PCB Physical Specifications
1.2 Connector Definitions
J1 CTRL CON
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
1 USBDM 2 USBDP 3 P20 4 BT_STS
5 MUTE_A 6 DACR 7 DACL 8 LINE_DET
9 GND 10 VCC_5V 11 VCC_5V
J2 LINE IN
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
1 GND 2 GND
J3 HEADPHONE
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
Pin No.
DESCRIPTION
1 GND 2 GND 3 RXD 4 TXD
page 3 / 6
Operational description
1.3 The Power VCC_5V to the BT Audio Module, When the Bluetooth module passes
through the music amplification line the sound output
1.4 BT search BT Audio Amplifier device, SPEAKER output music
page 4 / 6
FCC 警語置於使用者手冊
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate this
equipment. (Example - use only shielded interface cables when connecting to computer or
peripheral devices).
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be installed
such that 0.5 cm may be maintained between the antenna and users. The final end product must
be labeled in visible area with the following: “Contains FCC ID: 2ANCG-CS61006 ”
”
End Product Manual Information
The user manual for end users must include the following information in a prominent location
“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna
used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from
all persons and must not be colocated or operating in conjunction with any other antenna or
transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions (1) This device may not cause harmful interference and (2) This device
must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:In the event that these conditions can not be met (for example certain laptop
configurations or colocation with another transmitter), then the FCC authorization is no longer
page 5 / 6
considered valid and the FCC ID can not be used on the final product. In these circumstances, the
OEM integrator will be responsible for reevaluating the end product (including the transmitter) and
obtaining a separate FCC authorization. This device is intended only for OEM integrators under
the following conditions: The antenna must be installed such that 0.5 cm is maintained between the
antenna and users. As long as a condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end product for any additional
compliance requirements required with this module installed (for example, digital device emissions,
PC peripheral requirements, etc.).
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The host product shall be properly labelled to identify the modules within the host product.
The ISED certification label of a module shall be clearly visible at all times when installed in the host
product; otherwise, the host product must be labelled to display the ISED certification number for the
module, preceded by the word "contains" or similar wording expressing the same meaning, as follows:
Contains IC : 22282-CS61006
Le produit hôte devra être correctement étiqueté, de façon à permettre l'identification des modules qui
s'y trouvent.
L'étiquette d'homologation d'un module d'ISDE devra être apposée sur le produit hôte à un endroit bien
en vue, en tout temps. En l'absence d'étiquette, le produit hôte doit porter une étiquette sur laquelle
figure le numéro d'homologation du module d'ISDE, précédé du mot « contient », ou d'une formulation
similaire allant dans le même sens et qui va comme suit :
Contient IC : 22282-CS61006
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 0.5
cm between the radiator and your body.
Cet équipement est conforme aux CNR-102 d'Industrie Canada. Cet équipement
doit êtreinstallé et utilisé avec une distance minimale de 0.5 centimètres entre le
radiateur et votrecorps. Cet émetteur ne doit pas être co-localisées ou opérant en
page 6 / 6
conjonction avec autreantenne ou émetteur. Les antennes utilisées pour cet
émetteur doivent être installés etfournir une distance de séparation d'au moins
0.5 centimètre de toute personne et doit pas être co-située ni fonctionner en
conjonction avec une autre antenne ou émetteur.
-
1
-
2
-
3
-
4
-
5
-
6
dans d''autres langues
- English: CoreStar CS61006 User manual
Documents connexes
Autres documents
-
Hisense AEH-W0G1 Mode d'emploi
-
Intermec IM11 Integration Manual
-
RAK 272-SiP Breakout Board Manuel utilisateur
-
Telit Wireless Solutions xE910 Manuel utilisateur
-
-
Compex WLE1216VX WiFi 5 4×4 MU MIMO Dual Band Module Mode d'emploi
-
Compex WLE1216VX Dual Band Module Manuel utilisateur
-
LG SBWAC03 RF Module Manuel utilisateur
-
