JennAir JS48NXFXDE Le manuel du propriétaire

Marque: JennAir

Modèle: JS48NXFXDE

Catégorie: Frigos

Taper: Le manuel du propriétaire

W10779525A

Table of Contents/Índice/Table des matières...................................................................................2

USE AND CARE GUIDE

For questions about features, operation/performance, parts, accessories, or service,

call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.

MANUAL DE USO Y CUIDADO

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico,

llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.ca.

GUIDE D’UTILISATION ET D’ENTRETIEN

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247)

ou visitez notre site Web à www.jennair.ca.

JENN-AIR

SIDE BY SIDE

BUILT-IN REFRIGERATOR

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS JENN-AIR

RÉFRIGÉRATEUR ENCASTRÉ

CÔTE À CÔTE JENN-AIR

TABLE OF CONTENTS

REFRIGERATION SAFETY ........................................................ 3

Proper Disposal of Your Old Refrigerator .......................... 3

BEFORE USE ............................................................................. 4

Water Supply Requirements ................................................ 4

Water System Preparation ................................................... 4

Install Produce Preserver (on some models) ..................... 5

REFRIGERATOR USE ................................................................ 6

Power On/Off Switch ............................................................ 6

Using the Controls ................................................................ 6

Water and Ice Dispensers (on some models) .................... 8

Sabbath Mode ....................................................................... 8

Ice Maker and Storage Bin

(on some models - Accessory) ............................................ 9

Water Filtration System ...................................................... 10

REFRIGERATOR FEATURES ................................................... 11

Refrigerator Shelves ........................................................... 11

Temperature Controlled Deli Drawer ................................ 12

Crisper and Covers ............................................................. 12

Wine Rack ........................................................................... 13

FREEZER FEATURES .............................................................. 13

Freezer Shelf ....................................................................... 13

Freezer Basket .................................................................... 13

DOOR FEATURES .................................................................... 13

Door Bins ............................................................................. 13

REFRIGERATOR CARE ........................................................... 14

Cleaning ............................................................................... 14

Lights ................................................................................... 14

Power Interruptions ............................................................ 14

Vacation Care ...................................................................... 14

TROUBLESHOOTING .............................................................. 15

Refrigerator Operation ....................................................... 15

Temperature and Moisture ................................................. 16

Ice and Water ...................................................................... 16

ASSISTANCE OR SERVICE ..................................................... 18

In the U.S.A. ......................................................................... 18

In Canada ............................................................................ 18

ACCESSORIES ......................................................................... 18

PERFORMANCE DATA SHEETS ............................................. 19

WARRANTY .............................................................................. 20

ÍNDICE

SEGURIDAD DEL REFRIGERADOR ....................................... 21

Cómo deshacerse adecuadamente de

su refrigerador viejo ........................................................... 22

ANTES DE USAR ..................................................................... 22

Requisitos del suministro de agua .................................... 22

Preparación del sistema de agua...................................... 23

Instalación del preservador de alimentos frescos

(en algunos modelos) ......................................................... 24

USO DE SU REFRIGERADOR ................................................. 25

Interruptor de On/Off (encendido/apagado) .................... 25

Uso de los controles........................................................... 25

Sabbath Mode (Modo de descanso) ................................. 27

Despachadores de agua y hielo (en algunos modelos) .. 27

Fábrica de hielo y depósito

(en algunos modelos - Accesorio) .................................... 29

Sistema de ltración de agua ............................................ 30

CARACTERÍSTICAS DEL REFRIGERADOR .......................... 31

Estantes del refrigerador ................................................... 31

Cajón para carnes frías con temperatura controlada ..... 31

Cajones para verduras y tapas .......................................... 32

Portabotellas ....................................................................... 32

CARACTERÍSTICAS DEL CONGELADOR ............................. 32

Estante del congelador ...................................................... 32

Canastilla del congelador .................................................. 32

CARACTERÍSTICAS DE LA PUERTA...................................... 33

Recipientes de las puertas ................................................ 33

CUIDADO DE SU REFRIGERADOR ........................................ 33

Limpieza .............................................................................. 33

Luces ................................................................................... 34

Cortes de corriente ............................................................ 34

Cuidado durante las vacaciones ....................................... 34

SOLUCIÓN DE PROBLEMAS .................................................. 35

Funcionamiento del refrigerador ...................................... 35

Temperatura y humedad .................................................... 36

Hielo y agua ......................................................................... 36

AYUDA O SERVICIO TÉCNICO ............................................... 38

En los EE.UU. ...................................................................... 38

En Canadá ........................................................................... 38

ACCESORIOS .......................................................................... 38

HOJA DE DATOS DEL RENDIMIENTO ................................... 39

GARANTÍA ................................................................................ 40

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ........................................... 42

Mise au rebut appropriée de votre vieux réfrigérateur ... 43

AVANT L’UTILISATION ............................................................. 44

Spécications de l’alimentation en eau ........................... 44

Préparation du système d’eau........................................... 44

Installation du conservateur pour produits frais

(sur certains modèles) ........................................................ 45

UTILISATION DU RÉFRIGÉRATEUR ...................................... 46

Interrupteur d’alimentation On/Off (marche/arrêt) .......... 46

Utilisation des commandes ............................................... 46

Sabbath Mode (mode sabbat) ........................................... 48

Distributeurs d’eau et de glaçons

(sur certains modèles) ........................................................ 49

Machine à glaçons et bac d’entreposage (sur certains

modèles - accessoire) ........................................................ 51

Système de ltration d’eau ................................................ 52

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ........................ 53

Tablettes du réfrigérateur .................................................. 53

Centre de soins des ingrédients ....................................... 53

Bac à légumes et couvercles ............................................ 54

Casier à vin .......................................................................... 54

CARACTÉRISTIQUES DU CONGÉLATEUR ........................... 53

Tablette de congélateur ..................................................... 54

Panier du congélateur ........................................................ 54

CARACTÉRISTIQUES DE LA PORTE ..................................... 55

Compartiments dans la porte ............................................ 55

ENTRETIEN DU RÉFRIGÉRATEUR ........................................ 55

Nettoyage ............................................................................ 55

Lampes ................................................................................ 56

Pannes de courant ............................................................. 56

Entretien avant les vacances ............................................. 56

DÉPANNAGE ............................................................................ 57

Fonctionnement du réfrigérateur ...................................... 57

Température et humidité .................................................... 58

Glaçons et eau .................................................................... 58

ASSISTANCE OU SERVICE ..................................................... 60

ACCESSOIRES ......................................................................... 60

FEUILLES DE DONNÉES SUR LA PERFORMANCE ............. 61

GARANTIE ................................................................................ 62

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

REFRIGERATOR SAFETY

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■

Use nonflammable cleaner.

■

Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■

Use two or more people to move and install refrigerator.

■

Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

Proper Disposal of Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are

still dangerous, even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

BEFORE USE

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with warm water

and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in “Refrigerator Care.”

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Water Supply Requirements

Read all directions before you begin.

IMPORTANT:

■ When your refrigerator was installed, the water connection

from the water source should have been connected to your

refrigerator. If your refrigerator is not connected to a water

source, see “Connect to Water Line” in the Installation

Instructions. If you have any questions about your water

connection, see “Troubleshooting” or call a licensed, qualied

plumber.

■ If you turn the refrigerator on before the water line is

connected, turn the ice maker Off. See “Ice Maker and

Storage Bin.”

■ All installations must meet local plumbing code requirements.

Clean Before Using

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, see

“Troubleshooting” or call a licensed, qualied plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water ltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 psi (276 kPa).

If the water pressure to the reverse osmosis system is less than

40 psi (276 kPa):

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy usage.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See “Water Filtration

System.”

If you have questions about your water pressure, call a licensed,

qualied plumber.

Water System Preparation

Please read before using the water system. Follow the directions

specic to your model.

Style 1 (Dispenser Models)

IMPORTANT: After connecting the refrigerator to a water source

or replacing the water lter, follow the steps below to make sure

that the water system is properly cleaned. This will ush air from

the lter and water dispensing system, and prepare the water

lter for use.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or

after the system.

NOTE: If your model has a base grille lter system, make sure

the base grille lter is properly installed and the cap is in the

horizontal position.

1. Open the freezer door and turn off the ice maker. The On/

Off switch is located on the top right side of the freezer

compartment. Move the switch to the OFF (right) setting as

shown.

2. Use a sturdy container to depress and hold the water

dispenser lever for 5 seconds, and then release it for

5 seconds. Repeat until water begins to ow. Once water

begins to ow, continue depressing and releasing the

dispenser lever (5 seconds on, 5 seconds off) until a total

of 3 gal. (12 L) has been dispensed. This will ush air from

the lter and water dispensing system and prepare the water

lter for use. Additional ushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

3. Open the freezer door and turn on the ice maker. Move the

switch to the ON (left) position.

NOTES:

■ Allow 24 hours to produce the rst batch of ice.

■ Discard the rst three batches of ice produced.

■ Allow 3 days to completely ll ice container.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or

after the system.

NOTE: If your model has a base grille lter system, make sure

the base grille lter is properly installed and the cap is in the

horizontal position.

1. Turn on the ice maker. Lower the wire shutoff arm as shown.

Please refer to “Ice Maker and Storage Bin” for further

instructions on the operation of your ice maker.

NOTES:

■ Allow 24 hours to produce the rst batch of ice.

■ Allow 3 days to completely ll ice container.

■ Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

■ Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Style 2 (Non-Dispenser Models)

IMPORTANT: After connecting the refrigerator to a water source

or replacing the water lter, ll and discard two full containers of

ice to prepare the water lter for use, before using the ice.

Sensitivity to

Ethylene

Production

Apples High Very High

Asparagus Medium Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Medium High

Carrots Low Very Low

Citrus Fruit Medium Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Installing the Produce Preserver (on some models)

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

1. Wash the interior of a crisper drawer with a solution of mild

dish soap and warm water, and dry thoroughly.

2. Find the package containing the Produce Preserver inside the

refrigerator, and install the Produce Preserver into the crisper

drawer according to the instructions provided in the package.

Installing the Status Indicator (on some models)

The Produce Preserver comes with a status indicator, which

should be activated and installed at the same time the pouch

is installed.

1. Place the indicator face-down on a rm, at surface.

2. Apply pressure to the bubble on the back of the indicator

until the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator’s rear

bubble has not been popped.

Replacing the Produce Preserver

The disposable packets should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, see “Accessories” in the User Instructions

or User Guide.

1. Remove the used packets from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement packets and status indicator using

the instructions included in the package.

A. Power switch

Using the Controls

IMPORTANT:

■ The refrigerator control adjusts the refrigerator compartment

temperature. The freezer control adjusts the freezer

compartment temperature.

■ Wait 24 hours after you turn on the refrigerator before you put

food into it. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer controls to a

lower (colder) setting will not cool the compartments any

faster.

■ If the temperature is too warm or too cold in the refrigerator

or freezer, rst check the air vents to be sure they are not

blocked before adjusting the controls.

■ The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is rm.

■ The actual temperature may differ from the display when a

door is open for an extended period of time.

NOTE: The factory recommended set points are 0°F (-18°C) for

the freezer and 37°F (3°C) for the refrigerator.

REFRIGERATOR USE

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Power On/Off Switch

If you need to turn the power to your refrigerator On or Off,

you must remove the top grille assembly to access the power

switch. Turn the power to the refrigerator Off when cleaning your

refrigerator.

Standard Installation - Flush Grille

To remove the top grille panel:

1. Open the door(s).

2. Lift the top grille panel straight up, and then pull straight out.

Place the panel on a soft surface.

To replace the top grille panel:

1. Hook the panel brackets onto the mounting bolts extending

from the top of the refrigerator.

2. Pull the grille panel down slightly to lock into place.

Integrated Installation - Full Height Grille

To install the grille panel to the refrigerator:

1. Slide the upper and lower slots in each bracket onto

the mounting pins extending upward from the top of the

refrigerator.

2. Push the grille panel forward to fully engage the spring clips

and fasten the grille panel.

To remove the grille panel from the refrigerator:

1. Open the door(s).

2. Place both hands under the grille panel, grasping the bottom

edge between your ngers and thumbs.

3. Pull the grille panel straight out until the grille stops. Then, lift

up on the grille panel to remove.

Turn Power On or Off:

1. Remove top grille.

2. Press Power switch to the ON or OFF position.

3. Replace top grille.

IMPORTANT: Be sure the power switch is set to the ON position

after cleaning refrigerator or changing light bulbs.

Turning Refrigerator On and Viewing Set Points

■ Press the Cooling (ON/OFF) touch pad.

NOTE:

■ After the refrigerator is turned on, the Over Temperature audio

alarm and indicator light may activate every 1¹⁄₂ hours until the

refrigerator and freezer temperatures are below 48°F (9°C) and

15°F (-9°C), respectively, or until the alarm is turned off. To

turn off the audio alarm and indicator light, see “Master Alarm

Reset.”

■ The Cooling ON/OFF touch pad on the control panel shuts

down refrigerator functions such as cooling, lighting, fans and

compressors. To turn the power off completely, use the power

ON/OFF switch located behind the top grille. See “Power On/

Off Switch.”

Viewing the Celsius Temperatures

■ Press the F/C touch pad. To redisplay degrees Fahrenheit,

press F/C again.

NOTE: If the freezer temperature is below zero, the negative sign

next to the freezer display will light up. This is normal.

Adjusting Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To Adjust Set Point Temperatures:

■ Press the refrigerator or freezer PLUS (+) or MINUS (-) touch

pad until the desired temperature is reached.

■ Press the Set To Recommended touch pad to reset the set

points to the factory recommended temperatures.

NOTE: The set point range for the freezer is -5°F to 3°F (-21°C

to -16°C). The set point range for the refrigerator is 34°F to

42°F (1°C to 6°C).

CONDITION/REASON: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold

Not set correctly for conditions

REFRIGERATOR Control

1° higher

REFRIGERATOR too warm

High use or room very warm

REFRIGERATOR Control

1° lower

FREEZER too cold

Not set correctly for conditions

FREEZER Control

1° higher

FREEZER too warm/too little ice

High use or heavy ice use

FREEZER Control

1° lower

Water Filter Indicator and Reset

See “Water Filter Indicator” section.

Max Cool

The Max Cool feature assists with periods of heavy ice usage, full

grocery loads, or temporarily warm room temperatures.

■ Press MAX COOL to turn on the Max Cool feature. The Max

Cool indicator light will remain on for 24 hours unless manually

turned off.

NOTE: The temperature display will remain at 34°F (1°C) and

-5°F (-21°C) for the refrigerator and freezer compartments,

respectively, while the Max Cool feature is enabled. After 24

hours, the refrigerator returns to the previous temperature set

points.

Alarm Functions

Master Alarm Reset

Pressing Alarm Reset once will turn off the audio alarm and

indicator light. The audio alarm will not sound again for the

current condition that caused the alarm until a new condition

occurs or until a Master Alarm Reset is performed.

A Master Alarm Reset can be performed by pressing Cooling

(ON/ OFF) twice or by turning the power to the refrigerator off and

on again. See “Power On/Off Switch.” After performing a Master

Alarm Reset, the indicator light will reactivate if the condition that

caused the alarm is still present. See “Over Temperature,” “Call

Service,” or “Door Open.”

Door Open

The Door Open indicator light will ash, an alarm will sound

and the interior lights will turn off when a door has been open

for longer than 10 minutes. When the door is closed, the audio

alarm will reset and turn off, but the Door Open indicator light

will continue to ash until the temperature is equal to or below

45°F (7°C) and 15°F (-9°C) for the refrigerator and freezer

compartments, respectively.

NOTE: To deactivate the audio alarm and indicator light, see

“Master Alarm Reset.”

Over Temperature

IMPORTANT: If the Over Temperature Alarm activates, your

food may spoil. See the “Power Interruptions.” Minimize door

openings until temperatures return to normal.

The Over Temperature feature is designed to let you know when

either the refrigerator temperature rises above 48°F (9°C) or

the freezer temperature rises above 15°F (-9°C) for longer than

1¹⁄₂ hours. The audio alarm will shut off automatically when the

temperature returns to normal, but the indicator light will continue

to ash until the Alarm is pressed to let you know that an over

temperature condition has occurred.

■ Press SABBATH MODE again to turn off Sabbath Mode.

Dispenser Panel Holiday Mode (on some models)

In Holiday Mode, the dispenser levers are disabled and the

dispenser lights turn off.

■ To turn on Holiday Mode, press and hold ICE, LIGHT and

LOCKOUT at the same time for 3 seconds. When the feature

turns on, the indicator light around the LOCKOUT button will

blink and “HOL” will appear on the dispenser display.

■ To turn Holiday Mode off, press and hold ICE, LIGHT and

LOCKOUT at the same time for 3 seconds again.

NOTE: If the Max Cool feature has been selected prior to

turning on the Holiday Mode feature, then the set points will

remain at 34°F (1°C) and -5°F (-21°C) for the refrigerator and

freezer compartments, respectively, until the Max Cool feature

times out. The refrigerator will then return to the previous

temperature set points chosen prior to the selection of the

Max Cool feature, but the lights and ice maker will remain off

until the Holiday Mode is pressed again.

Water and Ice Dispensers

(on some models)

IMPORTANT:

■ After connecting the refrigerator to a water source or replacing

the water lter, ush the water system. Use a sturdy container

to depress and hold the water dispenser lever for 5 seconds,

then release it for 5 seconds. Repeat until water begins to

ow. Once water begins to ow, continue depressing and

releasing the dispenser lever (5 seconds on, 5 seconds off)

until a total of 3 gal. (12 L) has been dispensed. This will ush

air from the lter and water dispensing system, and prepare

the water lter for use. Additional ushing may be required in

some households.

NOTES:

■ While dispensing water and for 3 seconds after

dispensing has stopped, the digital display will show how

many ounces of water have been dispensed.

■ To switch from ounces to cups, press and hold ICE and

LOCK at the same time until the dispenser beeps after 3

seconds. To switch from cups to liters, press and hold the

buttons for another 3 seconds. To switch back to ounces,

repeat the process a third time.

2. Remove the glass to stop dispensing.

NOTE: Water may have an off-avor if you do not use the

dispenser periodically. Dispense enough water every week to

maintain a fresh supply.

Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when

the dispenser pad is pressed. The dispensing system will not

operate when the freezer door is open. To turn off the ice maker,

see “Ice Maker and Storage Bin.”

Your ice maker can produce both crushed and cubed ice. The

display screen reads “CRUSHED” or “CUBED,” indicating which

type is selected. To change the setting, press the ICE button

before dispensing ice.

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from crushed to cubed, a few ounces of crushed

ice will be dispensed along with the rst cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

If the over temperature condition is still present when an Over

Temperature Reset is performed, the indicator light will continue

to reactivate every 1¹⁄₂ hours until refrigerator and freezer

temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.

NOTE: The audio alarm will be disabled for subsequent

occurrences of over temperature alarm condition. To enable the

audio alarm, see “Master Alarm Reset.”

Sabbath Mode

The Sabbath Mode feature is designed for the traveler or for

those whose religious observances require turning off the lights

and ice maker. By selecting this feature, the temperature set

points and Deli Pan settings remain unchanged, the ice maker

will be disabled and the interior lights will turn off. For most

efcient refrigerator operation, it is recommended to exit the

Sabbath Mode when it is no longer required.

To fully activate Sabbath Mode, you must follow the instructions

below for both the control panel and dispenser panel (on some

models).

IMPORTANT: If you do not activate Sabbath Mode in both ways

listed below, some functions you wish to disable will remain

active.

Control Panel

In Sabbath Mode, the temperature set points remain unchanged

and the interior lights turn off.

■ Press SABBATH MODE to turn on Sabbath Mode.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

■ Allow 24 hours for the refrigerator to cool down and chill

water.

■ Allow 24 hours to produce the rst batch of ice. Discard the

rst three batches of ice produced.

■ The dispensing system will not operate when the freezer door

is open.

■ Depending on your model, your water and ice dispensers may

have one or more of the following features: a dispenser tray,

a special light that turns on when you use the dispenser, or a

lock option to avoid unintentional dispensing.

Water Dispenser

To Dispense Water:

1. Press a sturdy glass against the water dispenser pad.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

2. Press a sturdy glass against the ice dispenser pad. Hold

the glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the pad in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: Ice may continue to dispense for up to 10 seconds

after removing the glass from the pad. The dispenser may

continue to make noise for a few seconds after dispensing.

Dispenser Tray (on some models)

Some models have a tray at the bottom of the dispenser area.

The tray is designed to catch small spills and is removable for

easy emptying and cleaning.

NOTE: There is no drain in the tray.

Dispenser Light (on some models)

When you use the dispenser, the light will automatically turn on.

If you want the light to be on continuously, you may choose either

ON or AUTO.

ON: Press LIGHT to turn the dispenser light on.

AUTO: Press LIGHT a second time to select AUTO mode. The

dispenser light will automatically adjust to become brighter as the

room brightens and dimmer as the room darkens.

OFF: Press LIGHT a third time to turn the dispenser light off.

The dispenser lights are LEDs that cannot be changed. If it

appears that your dispenser lights are not working, be sure

that the light sensor is not blocked (in AUTO mode). See

“Troubleshooting” for more information.

Dispenser Lock (on some models)

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product,

to the ice maker, or to the dispenser light. It simply deactivates

the ice and water dispensers. To turn off the ice maker, see “Ice

Maker and Storage Bin.”

■ Press and hold LOCK for 3 seconds to lock the dispenser.

While the dispenser is locking, “LOCKING” will appear on the

display screen and the blue indicator light around the LOCK

button will ash. When the dispenser is locked, the indicator

light will change to red for a few seconds, and then turn off.

■ Press and hold LOCK a second time to unlock the dispenser.

While the dispenser is unlocking, “UNLOCKING” will appear

on the display screen and the red indicator light around the

LOCK button will ash. When the dispenser is unlocked, the

indicator light will change to blue for a few seconds, and then

turn off.

Water Filter Status Light (on some models)

The water lter status light and display screen help you know

when to change your water lter. Press the FILTER button to

check the status of your water lter.

If the filter is new:

You must press FILTER to view the lter’s status. For a few

seconds, the status light will be blue and the display screen will

show what percentage of your lter’s life remains.

If it is almost time to change the filter:

The status light will automatically illuminate and will remain on,

appearing yellow. The words “ORDER FILTER” will appear on

the display screen. Press FILTER to see what percentage of your

lter’s life remains. You should order the appropriate replacement

lter. See “Accessories.”

If it is time to change the filter:

The status light will remain on, changing to red. The words

“REPLACE FILTER” and “HOLD BUTTON TO RESET” will appear

on the display screen until the lter has been changed and the

status light has been reset.

To reset the water filter status light:

After changing the lter, reset the status light by pressing and

holding the FILTER button for 3 seconds. The status light will

blink red and change to blue, and then turn off when the system

is reset.

Ice Maker and Storage Bin

(on some models - Accessory)

IMPORTANT: Flush the water system before turning on the

ice maker. See “Water and Ice Dispensers.” Allow 24 hours to

produce the rst batch of ice. Discard the rst three batches of

ice produced. Allow 3 days to completely ll the ice container.

Style 1

To Turn the Ice Maker On/Off:

The On/Off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will ll the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position, and listen for the click to make sure

the ice maker will not continue to operate.

To Remove and Replace the Ice Bin:

1. Flip up the covering panel.

A. Ice maker cover

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull the ice bin forward.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2

To Turn the Ice Maker On/Off:

The On/Off switch is located on the top right side of the freezer

compartment.

1. To turn the ice maker on, slide the control to the ON (left)

position.

NOTE: Your ice maker has an automatic shutoff. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the OFF

(right) position.

To Remove and Replace the Ice Storage Bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to

the OFF (right) position when removing the storage bin. The

sensor cover (“ipper door”) on the left wall of the freezer

stops the ice maker from producing ice if the door is open or

the storage bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

Clean the Ice Storage Bin

NOTE: It is normal for ice to stick together in the ice bin. Ice may

be dispensed or used more frequently which will break up the ice.

It is recommended that the ice container be emptied and cleaned

as needed.

To clean the ice storage bin:

1. Empty the ice container. Use warm water to melt the ice if

necessary.

NOTE: Do not use anything sharp to break up the ice in the

bin or bucket. This can cause damage to the ice container

and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

Remember

■ Allow 24 hours to produce the rst batch of ice. Allow 3 days

to completely ll ice container.

■ Discard the rst three batches of ice produced to avoid

impurities that may be ushed out of the system.

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

■ Avoid connecting the ice maker to a softened water supply.

■ Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

■ It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

■ For Style 1 ice maker, do not force the wire shutoff arm up or

down.

■ Do not store anything on top of the ice maker or in the ice

storage bin/bucket.

Water Filtration System

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or

after the system.

Water Filter Indicator (on some models)

The water lter indicator, located on the control panel, will help

you know when to change the water lter.

A new water lter should display a reading of 99%. The reading

in the display will decrease as the lter life is used. A replacement

water lter should be ordered when “Order Filter” is displayed. It

is recommended that you replace the lter when “Change Filter”

is displayed or when water ow to your water dispenser and/or

ice maker decreases noticeably. See “Changing the Water Filter”

later in this section.

NOTE: Dispenser models have a lter reset on the freezer

compartment door. Non-Dispenser models have a Good/Order

Filter/Replace Filter indicator.

After changing the water lter, press and hold RESET for

2 seconds until the status display changes to 99%.

Changing the Water Filter

The water lter is located in the base grille below the freezer

compartment door. It is not necessary to remove the base grille

to remove the lter.

1. Remove the lter by pressing the eject button and pulling

straight out on the lter cap.

NOTES:

■ Avoid twisting the cap when removing the lter because

this could cause the cap to come off. If this occurs,

replace the cap and pull the lter straight out.

■ There will be water in the lter. Some spilling may occur.

A. Eject button

B. Filter cap

2. Remove the cap by turning it counterclockwise until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement lter.

3. Align the ridge on the cap with the arrow on the new lter, and

turn the cap until it snaps into place.

A. Cover

B. O-rings

4. Remove the covers from the O-rings. Be sure the O-rings are

still in place after the covers are removed.

5. Place the cap (removed in Step 2) on the new lter. Align the

ridge on the cap with the arrow on the lter. Turn the cap

clockwise until it snaps into place.

A. Eject button

B. Arrow on filter

C. Ridge on cap

6. Push the new lter into the opening in the base grille. As the

lter is inserted, the eject button will depress. The eject button

will pop back out when the lter is fully engaged.

7. Pull gently on the cap to check that the lter is securely

in place.

8. Flush the water system. Depending on your model, see

“Water and Ice Dispensers” or “Ice Maker and Storage Bin.”

Using the Ice Maker Without a Water Filter

You can operate the ice maker without a water lter. Your ice will

not be ltered.

1. Remove the lter by pressing the eject button and pulling on

the cap. See “Changing the Water Filter” earlier in this section.

2. Remove the cap by turning it counterclockwise until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement lter.

3. With the cap in a horizontal position, insert the cap into the

base grille until it stops.

4. Turn the cap counterclockwise until the cap slips into the

attachment slot. Then, turn the cap clockwise until it is in a

horizontal position.

NOTE: The cap will not be even with the base grille.

REFRIGERATOR FEATURES

Refrigerator Shelves

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

The shelves in your refrigerator are adjustable to meet your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to t different heights of items will make

nding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open and help save

energy.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf by tilting it up at the front and lifting it out of

the shelf supports. Pull shelf straight out.

2. Reposition the shelf supports in the desired location. Check

that they are level and rmly inserted in the support rails.

Temperature Controlled Deli Drawer

The control for the deli drawer adjusts the temperature of the

drawer. Cold air ows into the drawer through the air duct

between the freezer and the refrigerator. Adjusting the control

allows more or less cold air through the air duct.

Adjust the Temperature (Dispenser Models)

1. Choose a setting based on the item to be stored in the pan.

2. Push the button that corresponds to that setting.

3. The indicator light for that setting will illuminate to verify that

the pan is ready to be loaded.

Style 1

Remove and Replace the Top Cover

1. Remove food from Ingredient Care Center cover. Pull drawer

out about 4” (10.16 cm). Reach under the glass shelf with both

hands and lift gently upward until back of shelf is free. Tilt the

shelf at an angle and remove the shelf from the refrigerator. Be

sure not to bump the glass.

2. Replace the cover by holding the glass shelf rmly with both

hands. Tilt the shelf at an angle and position it above the

support rails. Place shelf gently on support rails on side wall.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh sh or shellsh......................... use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days

Cold cuts, steaks/roasts .................................................. 3-5 days

Cured meats................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Crisper and Covers

To remove and replace the crispers:

1. Slide the crisper drawer straight out to the stop. Lift the front

of the drawer with one hand while supporting the bottom of

the drawer with your other hand and slide the drawer out the

rest of the way.

2. To replace the crisper drawer, place the drawer onto slides

and push the drawer back until securely in position.

3. Test the crisper drawer to make sure it has been replaced

properly.

To clean crisper covers:

1. To clean the top crisper cover, remove the Ingredient Care

Center located above it.

2. To clean the bottom crisper cover, rst remove the top

crisper drawer.

3. Place the back of the shelf in the shelf supports.

4. Lower the front of the shelf and make sure that it is in position.

A. Deli drawer

B. Crisper

A. Crisper

B. Deli drawer

Style 2

Wine Rack

To remove and replace the wine rack:

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall

of the refrigerator.

FREEZER FEATURES

Freezer Shelf

To remove and replace the shelf:

1. Remove the shelf by lifting it up and pulling it straight out.

2. Replace the shelf by putting it over the supports and lowering

it into place.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of

food, the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating

ice crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 lbs of food per cubic foot

[907 to 1,350 g per 28 L] of freezer space). Leave enough space

in the freezer for air to circulate around packages. Be sure to

leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

Freezer Basket

The freezer basket can be used to store bags of frozen fruits

and vegetables that may slide off freezer shelves.

To remove and replace the freezer basket:

1. Pull the basket straight out to the stop.

2. Lift the front of the basket and slide it out the rest of the way.

3. Replace the basket by positioning it on the side wall guide

rails. Lift the basket front slightly while pushing it past the

guide rail stops and slide basket in the rest of the way.

DOOR FEATURES

Door Bins

Large door bins hold gallon containers and the smaller door bins

hold 2-liter bottles. The door bins are adjustable and removable

for easy cleaning and adjusting.

Gallon Door Bin

To install gallon door bin:

NOTE: The gallon door bin can only be placed on the

lower support.

1. Position gallon door bin above lowest door adjustment slot.

2. Push down to secure bin.

3. Adjust other bins as necessary to allow for milk or beverage

container height.

Door Bins

To remove and replace the door bins:

1. Remove the bin by lifting it up and pulling it out.

2. Replace the bin by sliding it in above the desired support

and pushing it down until it stops.

REFRIGERATOR CARE

Cleaning

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

build-up of odors. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Remove the top grille. See “Power On/Off Switch.”

2. Press power switch to OFF.

3. Remove all removable parts from inside, such as shelves,

crispers, etc.

4. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

■ Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, ammable uids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

■ To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt

[26 g to 0.95 L] of water).

5. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners, or cleaners containing

chlorine. Dry thoroughly with a soft cloth.

6. Clean the condenser coils located behind the top grille

ventilation panel regularly. Coils may need to be cleaned as

often as every other month. This may help save energy.

■ Use a vacuum cleaner with an extended attachment to

clean the condenser coils when they are dusty or dirty.

7. Press the power switch to ON.

8. Replace the top grille. See “Power On/Off Switch.”

Lights

The lights in both the refrigerator and freezer compartments

are LEDs which do not need to be replaced. If the lights do not

illuminate when the door is opened, call 1-800-536-6247 for

assistance or service.

Power Interruptions

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

■ Remove all frozen food and store it in a frozen food locker.

■ Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for 2 to

4 days.

■ If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially lled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and avor may be affected. If the

condition of the food is poor, dispose of it.

Vacation Care

Your refrigerator is equipped with the Sabbath Mode feature,

which is designed for the traveler who wishes to turn off the lights

and ice maker. By selecting this feature, the temperature set

points remain unchanged, the ice maker will be disabled and the

interior lights will turn off. For most efcient refrigerator operation,

it is recommended to exit Sabbath Mode when it is no longer

required.

If You Choose To Leave the Refrigerator On While

You’re Away:

1. Use up any perishables and freeze other items.

2. Press SABBATH.

3. If your refrigerator has an automatic ice maker, shut off water

supply to the ice maker.

4. Empty the ice bin.

5. When you return from vacation, press SABBATH to return to

normal operation.

If You Choose To Turn the Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3. Depending on your model, turn the Thermostat Control (or

Refrigerator Control) to OFF. See “Using the Controls.”

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Refrigerator Operation

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

■ Power cord unplugged? Plug into a grounded 3 prong outlet.

■ Is outlet working? Plug in a lamp to see if the outlet

is working.

■ Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

■ Are controls on? Make sure the refrigerator controls are on.

See “Using the Controls.”

■ Is refrigerator defrosting? Your refrigerator will regularly run

an automatic defrost cycle. Recheck in 30 minutes to see if it

is operating.

■ New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to

its high-efciency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to

this reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with an explanation.

■ Buzzing - heard when the water valve opens to ll the ice

maker

■ Pulsating - fans/compressor adjusting to optimize

performance

■ Rattling - ow of refrigerant, water line, or from items placed

on top of the refrigerator

■ Sizzling/Gurgling - water dripping on the heater during

defrost cycle

■ Popping - contraction/expansion of inside walls, especially

during initial cool-down

■ Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan

■ Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

There is no audible door open alarm

Has the door been open less than 10 minutes? The door open

alarm will only ash when the door has been open for 10 minutes.

The audible alarm will sound the rst time the door is left open

for more than 10 minutes. Subsequent door open alarms will only

ash. You must reset the audible alarm each time. See “Using the

Controls.”

The doors will not close completely

■ Door blocked open? Move food packages away from door.

■ Bin or shelf in the way? Push bin or shelf back in the

correct position.

The doors are difcult to open

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

■ Are the gaskets dirty or sticky? Clean gaskets with mild

soap and warm water.

The lights do not work

■ Is the refrigerator in Sabbath Mode? See “Using the

Controls.”

■ Has the door been open more than 10 minutes? See “Using

the Controls.”

Temperature and Moisture

Temperature is too warm

■ New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

■ Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

■ Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

■ Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See “Using the Controls.”

■ Refrigerator not cooling? For models with digital controls,

turn the refrigerator off and then on to reset. If this does not

correct the problem, call for service.

■ Air vents blocked? Remove any item from in front of the

air vents.

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

■ Humid room? Contributes to moisture buildup.

■ Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Ice and Water

The ice maker is not producing ice or not enough ice

■ Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

■ Kink in the water source line? A kink in the line can reduce

water ow. Straighten the water source line.

■ Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

■ New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

■ Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

■ Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

■ Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements” in either the Installation

Instruction booklet or the Use & Care Guide.

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

■ Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

■ Kink in the water source line? A kink in the line can reduce

water ow. Straighten the water source line.

■ Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

■ Questions remain regarding water pressure? Call a

licensed, qualied plumber.

Ice is sticking together in the ice storage bin

■ It is normal for frost to be on top of the ice storage bin due to

normal opening and closing of the freezer.

■ It is normal for ice to stick together when it is not dispensed or

used frequently. It is recommended that the ice storage bin be

emptied and cleaned as needed. See “Ice Maker and

Storage Bin.”

Off-taste, odor or gray color in the ice

■ New plumbing connections? New plumbing connections

can cause discolored or off-avored ice.

■ Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

■ Odor transfer from food? Use airtight, moisture proof

packaging to store food.

■ Are there minerals (such as sulfur) in the water? A water

lter may need to be installed to remove the minerals.

■ Is there a water lter installed on the refrigerator? Gray

or dark discoloration in ice indicates that the water ltration

system needs additional ushing.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

■ Is the ice dispenser stalling while dispensing “crushed”

ice? Change the ice button from “crushed” to “cubed.”

If cubed ice dispenses correctly, depress the button for

“crushed” ice and begin dispensing again.

■ Has the dispenser arm been held in too long? Ice will stop

dispensing when the arm is held in too long. Wait 3 minutes

for dispenser motor to reset before using again.

The water dispenser will not operate properly

■ Freezer door closed completely? Close the door rmly. If it

does not close completely, see “The doors will not

close completely.”

■ Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

■ Is the water pressure at least 30 psi (207 kPa)? The water

pressure to the home determines the ow from the dispenser.

See “Water Supply Requirements.”

■ Kink in the home water source line? Straighten the water

source line.

■ New installation? Flush and ll the water system.

■ Water lter installed on the refrigerator? The lter may be

clogged or incorrectly installed.

■ Is a reverse osmosis water ltration system connected to

your cold water supply? See “Water Supply Requirements”

in either the Installation Instructions or the Use & Care Guide.

The ice dispenser will not operate properly

■ Freezer door closed completely? Close the door rmly. If

it does not close completely, see “The doors will not close

completely.”

■ Ice bin installed correctly? Be sure the ice bin is rmly

in position.

■ New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full

ice production.

■ Ice stuck in the delivery chute? Use a plastic utensil to clear

the delivery chute.

■ Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker.

■ Has the ice melted around the auger (metal spiral) in the

ice bin? Empty the ice container. Use warm water to melt the

ice if necessary.

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

■ Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

■ New installation? Flush the water system. See “Prepare the

Water System” or “Water and Ice Dispensers.”

■ Recently changed water lter? Flush the water system. See

“Prepare the Water System” or “Water and Ice Dispensers.”

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

■ New installation? Allow 24 hours after installation for the

water supply to cool completely.

■ Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely.

■ Water not been recently dispensed? The rst glass of water

may not be cool. Discard the rst glass of water.

■ Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See “Water

Supply Requirements.”

ACCESSORIES

To order accessories, call 1-800-JENNAIR (1-800-536-6247),

and ask for the appropriate part number listed below or contact

your authorized Jenn-Air dealer. In Canada, call 1-800-807-6777.

Replacement Water Filter:

In U.S.A., order Part #4396841 (T2RFWG2)

In Canada, Order Part #4396841B (T2RFWG2)

Produce Preserver:

Order Part #W10593207

ASSISTANCE OR SERVICE

If You Need Service

Please refer to the warranty page in this manual.

If You Need Replacement Parts

If you need to order replacement parts, we recommend that

you use only factory specied parts. Factory specied parts will

t right and work right because they are made with the same

precision used to build every new Jenn-Air

appliance.

To locate factory specied parts in your area, call us or your

nearest designated service center.

In the U.S.A.

Call the Jenn-Air Customer eXperience Center toll free at

1-800-JENNAIR (1-800-536-6247), or visit our website at

www.jennair.com.

Our consultants provide assistance with:

■ Features and specications on our full line of appliances.

■ Referrals to local Jenn-Air brand dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For Further Assistance

If you need further assistance, you can write to Jenn-Air with any

questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Jenn-Air Canada Customer eXperience Centre toll free

1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.ca.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulll the product warranty

and provide after-warranty service anywhere in Canada.

■ Features and specications on our full line of appliances.

■ Referrals to local Jenn-Air brand dealers.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For Further Assistance

If you need further assistance, you can write to Jenn-Air Canada

with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

PERFORMANCE DATA SHEETS

Water Filtration System

Model P1WB2/P1RFWB2 Capacity 200 Gallons (757 Liters)

Model P1WB2L/P1RFWB2L Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI

Standard 42, Standard 53, and Standard 401 for the reduction of

contaminants specified on the Performance Data Sheet.

This system has been tested according to NSF/ANSI Standards 42, 53 and 401 for the reduction of the substances listed below.

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible

limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53, and 401.

Substance Reduction

Aesthetic Effects

Influent Challenge Concentration Maximum Permissible

Product Water Concentration

Average % Reduction

Chlorine Taste/Odor 2.0 mg/L ± 10% ≥50% reduction >97.5%

Particulate Class I* At least 10,000 particles/mL ≥85% reduction 99.2%

Contaminant Reduction Influent Challenge Concentration Maximum Permissable

Product Water Concentration

Average %

Reduction

Lead***: @ pH 6.5 / @ pH 8.5 0.150 mg/L ± 10% 0.010 mg/L >99.3% / >99.3%

Mercury: @ pH 6.5 / @ pH 8.5 0.006 mg/L ± 10% 0.002 mg/L >96.4% / 90.8%

Asbestos 10

to 10

bers/L

††

99% 99%

Cysts

†

50,000/L min. 99.95% >99.99%

Turbidity 11 NTU ± 10% 0.5 NTU >99.1%

Alchor 0.040 mg/L ± 10% 0.002 mg/L 97.6%

Atrazine 0.009 mg/L ± 10% 0.003 mg/L 94.5%

Benzene 0.015 mg/L ± 10% 0.005 mg/L 96.6%

Carbofuran 0.080 mg/L ± 10% 0.040 mg/L 91.1%

Chlorobenzene 2.000 mg/L ± 10% 0.100 mg/L 99%

Endrin 0.006 mg/L ± 10% 0.002 mg/L 96.6%

Ethylbenzene 2.100 mg/L ± 10% 0.700 mg/L 99.9%

Lindane 0.002 mg/L ± 10% 0.0002 mg/L 99%

MTBE MTBE 0.015 mg/L ± 10% 0.005 mg/L 90.6%

O-Dichlorobenzene 1.800 mg/L ± 10% 0.600 mg/L 99.9%

Tetrachloroethylene 0.015 mg/L ± 10% 0.005 mg/L 96.4%

Toxaphene 0.015 mg/L ± 10% 0.003 mg/L >93.7%

TTHM 0.045 mg/L ± 10% 0.080 mg/L 99.5%

Styrene 2.000 mg/L ± 10% 0.100 mg/L 99.9%

VOC 0.300 mg/L ± 10% 0.015 mg/L 99.7%

Atenolol 200 ± 20% 30 ng/L 95.7%

Trimethoprim 140 ± 20% 20 ng/L 96.1%

Linuron 140 ± 20% 20 ng/L 96.3%

Estrone 140 ± 20% 20 ng/L 90.6%

Nonylphenol 1400 ± 20% 200 ng/L 93.7%

■ It is important that operational, maintenance, and filter replacement

requirements be carried out for the product to perform as

advertised. Property damage can occur if all instructions are not

followed.

■ The disposable cartridge must be changed at least every 6 months.

■ Use replacement filter P1RFWB2L, Part #EDR3RXD1/EDR3RXD1B.

2015 suggested retail price of $49.99 U.S.A./$54.95 Canada.

Prices are subject to change without notice.

■ The filter monitor system measures the amount of water that

passes through the filter and alerts you when it is time to replace

the filter. To learn how to check the water filter status, see “Using

the Controls” or “Water Filtration System” in the User Instructions

or User Guide.

■ After changing the water filter, flush the water system. See “Water

and Ice Dispensers” or “Water Dispenser” in the User Instructions

or User Guide.

■ These contaminants are not necessarily in your water supply. While

testing was performed under standard laboratory conditions, actual

performance may vary.

■ The product is for cold water use only.

Application Guidelines/Water Supply Parameters

Water Supply Potable City or Well

Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33° - 100°F (0.6° - 37.8° C)

Service Flow Rate 0.5 GPM (1.89 L/min.) @ 60 psi.

* Class I particle size: >0.5 to <1 um

*** Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.

†

Based on the use of Cryptosporidium parvum oocysts

††

Test requirement is at least 100,000 particles/mL of AC Fine Test Dust

® NSF is a registered trademark of NSF International.

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/incidental

contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these

compounds can affect the public acceptance/perception of drinking water quality.

■ The water system must be installed in compliance with state and

local laws and regulations.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used on

disinfected waters that may contain filterable cysts. EPA Est. No.

082047-TWN-001

■ Refer to the “Warranty” section (in the User Instructions or User

Guide) for the Manufacturer’s limited warranty, name and telephone

number.

12/14

JENN-AIR

REFRIGERATION

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit https://jennair.custhelp.com.

2. All warranty service is provided exclusively by our authorized Jenn-Air Service Providers

. In the U.S. and

Canada, direct all requests for warranty service to:

Jenn-Air Customer eXperience Center

1-800-JENNAIR (1-800-536-6247)

If outside the 50 United States or Canada, contact your authorized Jenn-Air dealer to determine whether another warranty applies.

https://jennair.custhelp.com

TEN YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

TWO YEAR LIMITED WARRANTY (PARTS & LABOR)

For two years from the date of purchase, when this major appliance is installed,

operated and maintained according to instructions attached to or furnished with

the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP

(hereafter “Jenn-Air”) will pay for Factory Specified Replacement Parts and

repair labor to correct defects in materials or workmanship that existed when

this major appliance was purchased, or at its sole discretion replace the

product. In the event of product replacement, your appliance will be warranted

for the remaining term of the original unit's warranty period.

THIRD THROUGH FIFTH YEAR LIMITED WARRANTY ON

CAVITY LINER AND SEALED REFRIGERATION SYSTEM

In the third through fifth years from the date of purchase, when this major

appliance is installed, operated and maintained according to the instructions

attached to or furnished with the product, Jenn-Air brand will pay for factory

specified replacement parts and repair labor for the following components to

correct non-cosmetic defects in materials and workmanship in this part that

prevent function of the refrigerator and that existed when this major appliance

was purchased:

■ Refrigerator/freezer cavity liner if the part cracks due to defective materials

or workmanship.

■ Sealed Refrigeration system (includes compressor, evaporator, condenser,

dryer and connecting tubing).

SIXTH THROUGH TENTH YEAR LIMITED WARRANTY

(SEALED REFRIGERATION SYSTEM ONLY - LABOR NOT INCLUDED)

In the sixth through tenth year from the date of purchase, when this major

appliance is installed, operated and maintained according to instructions

attached to or furnished with the product, Jenn-Air brand will pay for factory

specified replacement parts for the following components to correct defects in

materials or workmanship in the sealed refrigeration system (includes

compressor, evaporator, condenser, dryer and connecting tubing) that existed

when this major appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service must be

provided by a Jenn-Air designated service company. This limited warranty is

valid only in the United States or Canada and applies only when the major

appliance is used in the country in which it was purchased. This limited

warranty is effective from the date of original consumer purchase. Proof of

original purchase date is required to obtain service under this limited warranty.

1. Commercial, non-residential or multiple-family use, or use

inconsistent with published user, operator or installation

instructions.

2. In-home Instruction on how to use your product.

3. Service to correct improper product maintenance or installation,

installation not in accordance with electrical or plumbing codes

or correction of household electrical or plumbing (i.e. house

wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters,

preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Jenn-Air

parts or accessories.

6. Damage from accident, misuse, abuse, fire, floods, acts of God

or use with products not approved by Jenn-Air.

7. Repairs to parts or systems to correct product damage or

defects caused by unauthorized service, alteration or

modification of the appliance.

8. Cosmetic damage including scratches, dents, chips, and other

damage to appliance finishes unless such damage results from

defects in materials and workmanship and is reported to Jenn-Air

within 30 days.

9. Discoloration, rust or oxidation of surfaces resulting from caustic

or corrosive environments including but not limited to high salt

concentrations, high moisture or humidity or exposure to

chemicals.

10. Food or medicine loss due to product failure.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations

where an authorized Jenn-Air servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in

fixtures (i.e. trim, decorative panels, flooring, cabinetry, islands,

countertops, drywall, etc.) that interfere with servicing, removal or

replacement of the product.

14. Service or parts for appliances with original model/serial

numbers removed, altered or not easily determined.

The cost of repair or replacement under these excluded

circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the

duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you

also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you

should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-AIR SHALL

NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental

or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may

have other rights that vary from state to state or province to province.

La page charge ...

JennAir JS48NXFXDE Le manuel du propriétaire

Marque: JennAir

Modèle: JS48NXFXDE

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: JennAir JS48NXFXDE Owner's manual
español: JennAir JS48NXFXDE El manual del propietario

JennAir JS48NXFXDE Le manuel du propriétaire

JennAir JS48NXFXDE Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents