Bay Networks Contivity 4000 Upgrade Manual

Marque: Bay Networks

Modèle: Contivity 4000

Taper: Upgrade Manual

Ce manuel convient également à

4000

Part No. 303321-A Rev. 00

July 1998

Voice Gateway 4000

Upgrade Guide

303321-A Rev. 00

4401 Great America Parkway 8 Federal Street

Santa Clara, CA 95054 Billerica, MA 01821

The information in this document is subject to change without notice. The statements, configurations, technical data,

and recommendations in this document are believed to be accurate and reliable, but are presented without express or

implied warranty. Users must take full responsibility for their applications of any products specified in this document.

The information in this document is proprietary to Bay Networks, Inc.

Trademarks

Bay Networks is a registered trademark and the Bay Networks logo is a trademark of Bay Networks, Inc.

All other trademarks and registered trademarks are the property of their respective owners.

Restricted Rights Legend

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subparagraph

(c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013.

Notwithstanding any other license agreement that may pertain to, or accompany the delivery of, this computer

software, the rights of the United States Government regarding its use, reproduction, and disclosure are as set forth in

the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Bay Networks, Inc. reserves the

right to make changes to the products described in this document without notice.

Bay Networks, Inc. does not assume any liability that may occur due to the use or application of the product(s) or

circuit layout(s) described herein.

303321-A Rev. 00 iii

USA Requirements Only

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case users will be required to take whatever measures may be necessary to correct the

interference at their own expense.

European Requirements Only

EN 55 022 Statement

This is to certify that the Bay Networks Voice Gateway 4000 is shielded against the generation of radio interference in

accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the

application of EN 55 022 Class A (CISPR 22).

Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which

case, the user may be required to take appropriate measures.

EC Declaration of Conformity

This product conforms (or these products conform) to the provisions of Council Directive 89/336/EEC and

73/23/EEC. The Declaration of Conformity is available on the Bay Networks World Wide Web site at

www.baynetworks.com.

Japan/Nippon Requirements Only

Voluntary Control Council for Interference (VCCI) Statement

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information

Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise.

When such trouble occurs, the user may be required to take corrective actions.

iv 303321-A Rev. 00

Canada Requirements Only

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (Voice Gateway 4000) does not exceed the Class A limits for radio-noise emissions from digital

apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique (Voice Gateway 4000) respecte les limites de bruits radioélectriques visant les appareils

numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des

Communications du Canada.

Canada CS-03 Rules and Regulations

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to

the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The

customer should be aware that compliance with the above conditions may not prevent the degradation of service in

some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines

and internal metallic water pipe system, if present, are connected together. This precaution may be particularly

important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric

inspection authority, or electrician, as appropriate.

Notice: For equipment using loopstart lines, please note that the Ringer Equivalence Number (REN) assigned to each

terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone

interface. The termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the “FCC

Rules Part 68” label located on the bracket of the module, or on the back of the unit.

Canada CS-03 -- Règles et règlements

Av is : L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est

conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le

prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure

toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur.

Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise

locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de

raccordement. L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions énoncées ci-dessus

n'empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur.

L'entreprise de télécommunications peut demander à l'utilisateur de débrancher un appareil à la suite de réparations ou

de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'énergie électrique,

des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution

est particulièrement importante dans les régions rurales.

303321-A Rev. 00 v

Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service

d'inspection des installations électriques, ou à un électricien, selon le cas.

Av is: Veuillez prendre note que pour tout appareillage supportant des lignes de type “loopstart,” l'indice d'équivalence

de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être

raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques

dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas

5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur le support du module ou à l’arrière de l’unité.

FCC Part 68 Compliance Statement

This equipment complies with Part 68 of FCC Rules. All direct connections to telephone network lines must be made

using standard plugs and jacks compliant with FCC Part 68. Please note the following:

1. You are required to request service from the telephone company before you connect the unit to a network. When

you request service, you must provide the telephone company with the following data:

• When you request T1 Service, you must provide the telephone company with

-- The Facility Interface Code

Provide the telephone company with all the codes below:

- 04DU9-BN (1.544 MB, D4 framing format)

- 04DU9-DN (1.544 MB, D4 framing format with B8ZF coding)

- 04DU9-1KN (1.544 MB, ESF framing format)

- 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)

- 04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI without line power)

The telephone company will select the code it has available.

-- The Service Order Code(s) (SOC): 6.0F

-- The required Universal Service Order Code (USOC) jack: RJ48C

• When you request 56K/64K Service, you must provide the telephone company with

-- The Facility Interface Code: 04DU5-56/64

-- The Service Order Code(s) (SOC): 6.0F

-- The required Universal Service Order Code (USOC) jack: RJ48S

• When you request V.34 Service, you must provide the telephone company with

-- The required Universal Service Order Code (USOC) jack: RJ11C

-- The make, model number, Ringer Equivalence Number (REN), and FCC Registration number of the

unit

The REN helps you determine the number of devices you can connect to your telephone line and still have

all of those devices ring when your number is called. In most, but not all, areas, the sum of the RENs of all

devices should not exceed 5.0. To be certain of the number of devices you can connect to your line, you

should call your local telephone company to determine the maximum REN for your calling area.

2. Your telephone company may make changes to its facilities, equipment, operations, or procedures that could

affect the proper functioning of your equipment. The telephone company will notify you in advance of such

changes to give you an opportunity to maintain uninterrupted telephone service.

3. If the unit causes harm to the telephone network, the telephone company may temporarily discontinue your

service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as

soon as possible and will be informed of your right to file a complaint with the FCC.

4. If you experience trouble with the unit, please contact the Bay Networks Technical Solutions Center in your area

for service or repairs. Repairs should be performed only by service personnel authorized by Bay Networks, Inc.

vi 303321-A Rev. 00

United States 1-800-2LANWAN

Valbonne, France 33-4-92-96-69-68

Sydney, Australia 61-2-9927-8800

Tokyo, Japan 81-3-5402-0180

5. You are required to notify the telephone company when you disconnect the unit from the network.

303321-A Rev. 00

vii

Contents

About This Guide

Before You Begin .............................................................................................................. xi

Conventions ......................................................................................................................xii

Bay Networks Technical Publications ..............................................................................xiii

Bay Networks Customer Service .....................................................................................xiii

How to Get Help ..............................................................................................................xiv

Bay Networks Educational Services ................................................................................xiv

Chapter 1

Chassis, Card Types, and Upgrade Overview

Chassis Overview ...........................................................................................................1-1

Card Type Descriptions ..................................................................................................1-2

1-Span Voice Gateway Description ..........................................................................1-3

2-Span Voice Gateway Description ..........................................................................1-4

3-Span Voice Gateway Description ..........................................................................1-5

4-Span Voice Gateway Description ..........................................................................1-6

Upgrade Overview ..........................................................................................................1-7

Chapter 2

Installing the Cards

Steps to Installing the Cards ...........................................................................................2-1

Chapter 3

Configuring the Software

Steps to Configuring Operating System Settings ...........................................................3-1

Run CPCFG .............................................................................................................3-1

Configuring the Network Adapters and Protocols ....................................................3-3

Appendix A

Switch and Jumper Settings

Switch and Jumper Settings .......................................................................................... A-1

viii

303321-A Rev. 00

TX-2000 Card .......................................................................................................... A-1

TX-2000 First Span (Memory Address D0000, Interrupt Request 5) ............... A-2

TX-2000 Second Span (Memory Address D2000, Interrupt Request 7) .......... A-2

TX-2000 Third Span (Memory Address D4000, Interrupt Request 9) .............. A-3

TX-2000 Fourth Span (Memory Address D6000, Interrupt Request 11) .......... A-3

AG-T1/E1 Card ....................................................................................................... A-4

AG-T1/E1 First Span (Base Memory Address 02C0) ....................................... A-4

AG-T1/E1 Second Span (Base Memory Address 22C0) .................................. A-5

AG-T1/E1 Third Span (Base Memory Address 42C0) ......................................A-5

AG-T1/E1 Fourth Span (Base Memory Address 62C0) ................................... A-5

303321-A Rev. 00

Figures

Figure 1-1. Top View of Inside of Voice Gateway with Cover Removed .....................1-1

Figure 1-2. AG-T1/E1 Card and TX-2000 Card ..........................................................1-2

Figure 1-3. 1-Span Voice Gateway Configuration ......................................................1-3

Figure 1-4. 2-Span Voice Gateway Configuration ......................................................1-4

Figure 1-5. 3-Span Voice Gateway Configuration ......................................................1-5

Figure 1-6. 4-Span Voice Gateway Configuration ......................................................1-6

Figure 2-1. MVIP Bus Cable .......................................................................................2-3

Figure 3-1. Select NMS Communications Processor Screen .....................................3-1

Figure 3-2. Select NMS Communications Processor Screen with Previous Board ....3-3

Figure 3-3. Microsoft TCP/IP Properties Dialog Box ..................................................3-4

Figure 3-4. TX-2000 First Span Switch and Jumper Settings ................................... A-2

Figure 3-5. TX-2000 Second Span Switch and Jumper Settings .............................. A-2

Figure 3-6. TX-2000 Third Span Switch and Jumper Settings .................................. A-3

Figure 3-7. TX-2000 Fourth Span Switch and Jumper Settings ................................ A-3

Figure 3-8. AG-T1/E1 First Span Switch Settings ..................................................... A-4

Figure 3-9. AG-T1/E1 Second Span Switch Settings ................................................ A-5

Figure 3-10. AG-T1/E1 Third Span Switch Settings .................................................... A-5

Figure 3-11. AG-T1/E1 Fourth Span Switch Settings ..................................................A-5

303321-A Rev. 00

About This Guide

If you are responsible for upgrading your Voice Gateway 4000 chassis, you need

to read this guide.

Before You Begin

Be sure to complete the

NetSpeak License Upgrade Registration

card that you

received with your Upgrade package and fax it to the number listed on the card.

Once you complete and fax the form, you will receive the corresponding

registration file by e-mail.

If you want to Go to

Obtain preliminary upgrade information on card types and the upgrade

process in general

Chapter 1

Learn how to install the cards and install the MVIP bus cable Chapter 2

Obtain instructions for configuring the gateway software Chapter 3

Learn how to set the switches and jumpers for the cards Appendix A

Note:

You will not be able to complete the installation without the registration

file.

Caution:

Once you receive the registration file by e-mail, copy it to your

c:\NetSpeak\config

directory.

Voice Gateway 4000 Upgrade Guide

xii

303321-A Rev. 00

For information on proper operating environment requirements, refer to your

Voice Gateway 4000 Hardware Manual

Conventions

bold text

Indicates text that you need to enter in menu paths and

fields, as well as indicates the names of buttons, tabs,

check boxes, menu commands, and keyboard functions

which should be selected or pressed.

Example: Enter

NSINST

on the command line.

Example: Use the

dinfo

command.

Example: Click on the

button.

Example: Enter a new user name in the

Database User

Name

field.

Example: Click on the

Database

tab.

Example: Select the

Use Defaults

check box.

Example:

1. Choose

New

from the

File

menu.

Example: Press the

Alt

key.

italic text

Indicates variable values in command syntax

descriptions, new terms, file and directory names, and

book titles.

quotation marks (“ ”) Indicates the title of a chapter or section within a book.

screen text

Indicates data that appears on the screen.

Example:

,,,Friendly/Fred, fred,

fred@acme.com,199.999.9.99,,,

About This Guide

303321-A Rev. 00

xiii

Bay Networks Technical Publications

You can now print technical manuals and release notes free, directly from the

Internet. Go to

support.baynetworks.com/library/tpubs

. Find the Bay Networks

products for which you need documentation. Then locate the specific category and

model or version for your hardware or software product. Using Adobe Acrobat

Reader, you can open the manuals and release notes, search for the sections you

need, and print them on most standard printers. You can download Acrobat

Reader free from the Adobe Systems Web site,

www.adobe.com

Documentation sets and CDs are available through your local Bay Networks sales

office or account representative.

Bay Networks Customer Service

You can purchase a support contract from your Bay Networks distributor or

authorized reseller, or directly from Bay Networks Services. For information or to

purchase a Bay Networks service contract, either call your local Bay Networks

field sales office or one of the following numbers:

Information about customer service is also available on the World Wide Web at

support.baynetworks.com

Region Telephone number Fax number

United States and

Canada

800-2LANWAN; then enter Express Routing

Code (ERC) 322, when prompted, to

purchase or renew a service contract

978-916-8880 (direct)

978-916-3514

Europe 33-4-92-96-69-66 33-4-92-96-69-96

Asia/Pacific 61-2-9927-8888 61-2-9927-8899

Latin America 561-988-7661 561-988-7550

Voice Gateway 4000 Upgrade Guide

xiv

303321-A Rev. 00

How to Get Help

If you purchased a service contract for your Bay Networks product from a

distributor or authorized reseller, contact the technical support staff for that

distributor or reseller for assistance.

If you purchased a Bay Networks service program, call one of the following Bay

Networks Technical Solutions Centers:

Bay Networks Educational Services

Through Bay Networks Educational Services, you can attend classes and purchase

CDs, videos, and computer-based training programs about Bay Networks

products. Training programs can take place at your site or at a Bay Networks

location. For more information about training programs, call one of the following

numbers:

Technical Solutions Center Telephone number Fax number

Billerica, MA 800-2LANWAN 978-916-3514

Santa Clara, CA 800-2LANWAN 408-495-1188

Valbonne, France 33-4-92-96-69-68 33-4-92-96-69-98

Sydney, Australia 61-2-9927-8800 61-2-9927-8811

Tokyo, Japan 81-3-5402-0180 81-3-5402-0173

Region Telephone number

United States and Canada 800-2LANWAN; then enter Express Routing Code (ERC)

282 when prompted

978-916-3460 (direct)

Europe, Middle East, and

Africa

33-4-92-96-15-83

Asia/Pacific 61-2-9927-8822

Tokyo and Japan 81-3-5402-7041

303321-A Rev. 00

1-1

Chapter 1

Chassis, Card Types, and Upgrade Overview

Chassis Overview

In order to begin upgrading your chassis, it is important to review the chassis

itself. Figure 1-1 shows a top-down view of the inside of the chassis, including

where the power supply, drive bay, and card slots are located. Be sure to review

this figure before starting with the section Card Type Descriptions

Figure 1-1. Top View of Inside of Voice Gateway with Cover Removed

Drive Bay

Power

Supply

Card Slots: See

Figure 1-3

(1-span),

Figure 1-4

(2-span),

Figure 1-5

(3-span),

and Figure 1-6

(4-span) for more

information on specific

card slot locations.

Voice Gateway 4000 Upgrade Guide

1-2

303321-A Rev. 00

Card Type Descriptions

In receiving this upgrade packet, you have decided to either upgrade your Voice

Gateway 4000 to a 2-span, 3-span, or 4-span unit. The figures in this chapter show

how each span type is set up. Review your current span type setup as well as your

planned upgrade span

before

beginning the installation.

• 1-Span Voice Gateway Description

• 2-Span Voice Gateway Description

• 3-Span Voice Gateway Description

• 4-Span Voice Gateway Description

Figure 1-2. AG-T1/E1 Card and TX-2000 Card

Note:

For the purposes of this document, each span type is known as a card

pair which includes the AG-T1/E1 card and the TX-2000 card (Figure 1-2).

MVIP Bus Cable

TX-2000 card

AG-T1/E1 card

Chassis, Card Types, and Upgrade Overview

303321-A Rev. 00

1-3

1-Span Voice Gateway Description

If you currently have a 1-span Voice Gateway, its card pair is set up as follows in

Figure 1-3. For more information, see Figure 1-1.

Figure 1-3. 1-Span Voice Gateway Configuration

AG-T1/E1

TX-2000

Empty

Processor

End Plate

Power Supply

Drive Bay

Front of Chassis

Back of Chassis

Span 1

Voice Gateway 4000 Upgrade Guide

1-4

303321-A Rev. 00

2-Span Voice Gateway Description

The 2-span Voice Gateway has two card pairs and is set up as follows in

Figure 1-4. For more information, see Figure 1-1.

Figure 1-4. 2-Span Voice Gateway Configuration

AG-T1/E1

TX-2000

Empty

Processor

End Plate

TX-2000

Power Supply

Drive Bay

Front of Chassis

Back of Chassis

Span 1 Span 2

AG-T1/E1

Chassis, Card Types, and Upgrade Overview

303321-A Rev. 00

1-5

3-Span Voice Gateway Description

The 3-span Voice Gateway has three card pairs and is set up as follows in

Figure 1-5. For more information, see Figure 1-1.

Figure 1-5. 3-Span Voice Gateway Configuration

AG-T1/E1

TX-2000

Empty

Processor

End Plate

TX-2000

Empty

TX-2000

Power Supply

Drive Bay

Front of Chassis

Back of Chassis

Span 1 Span 2 Span 3

AG-T1/E1

Voice Gateway 4000 Upgrade Guide

1-6

303321-A Rev. 00

4-Span Voice Gateway Description

The 4-span Voice Gateway has four card pairs and is set up as follows in

Figure 1-6. For more information, see Figure 1-1.

Figure 1-6. 4-Span Voice Gateway Configuration

AG-T1/E1

TX-2000

Processor

End Plate

TX-2000

Power Supply

Drive Bay

Front of Chassis

Back of Chassis

Span 1 Span 2 Span 3 Span 4

AG-T1/E1

La page charge ...

Bay Networks Contivity 4000 Upgrade Manual

Marque: Bay Networks

Modèle: Contivity 4000

Taper: Upgrade Manual

Ce manuel convient également à

4000

Télécharger le PDF

rapport

dans d''autres langues

English: Bay Networks Contivity 4000

Bay Networks Contivity 4000 Upgrade Manual

Ce manuel convient également à

Bay Networks Contivity 4000 Upgrade Manual

dans d''autres langues

Autres documents