GE PZS22MSKSS Guide d'installation

Marque: GE

Modèle: PZS22MSKSS

Catégorie: Frigos

Taper: Guide d'installation

GEAppliances.com

Refrigerators

Profile Side by Side

200D8074P052 49-60647-4 10-14 GE

La section française commence à la page 47

La sección en español empieza en la página 93

Safety Instructions ............2–4

Operating Instructions

Automatic Ice maker ...........15, 16

Care and Cleaning .............18, 19

ClimateKeeper2

™

....................6

Crispers and Pans ..................14

CustomCool

™

.....................7, 9

Ice and Water Dispenser .......17–18

Quick Ice ...........................17

Refrigerator Doors .................13

Replacing the Light Bulbs ...........20

Set Features ........................6

Shelves and Bins ...............11, 12

Temperature Controls ...............5

TurboCool

™

.........................6

Water Filter ........................10

Installation Instructions

Installing the Refrigerator .......30–33

Moving the Refrigerator ........26–29

Preparing to Install

the Refrigerator ....................25

Trim Kits and Panels ............21–24

Water Line Installation .........34–36

Troubleshooting Tips ......38–40

Normal Operating Sounds ..........37

Consumer Support

Performance Data Sheets ......43, 44

Warranty (U.S.) .....................42

Réfrigérateurs

Profile Côte à Côte

Refrigeradores

Profile Lado a Lado

Models 22, 23, 25, 26, 27 and 29

Write the model and serial numbers

here:

Model # _________________________

Serial # __________________________

Find these numbers on a label inside

the refrigerator compartment at the

top on the right side.

Owner’s Manual

and Installation

Manuel d’utilisation

et d’installation

Manual del propietario

e instalación

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

GE Appliances website

For more information on your refrigerator’s operation, visit www.GEAppliances.com or

call 800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety

messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

REFRIGERATOR SAFETY INFORMATION

SAFETY

WARNING

DANGER

CAUTION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

WARNING

 Do not clean glass shelves or covers with warm water when

they are cold. Glass shelves and covers may break if exposed

to sudden temperature changes or impact, such as bumping

or dropping. Tempered glass is designed to shatter into many

small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances

between the doors and between the doors and cabinet are

necessarily small. Be careful closing doors when children are in

the area.

 Always clean the CustomCool

™

Tray after thawing food.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet, skin may stick to these

extremely cold surfaces.

 Do not refreeze frozen foods which have thawed completely.

 In refrigerators with automatic icemakers, avoid contact with

the moving parts of the ejector mechanism, or with the heating

element that releases the cubes. Do not place fingers or hands

on the automatic ice making mechanism while the refrigerator

is plugged in.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of injury when using your refrigerator, follow these basic

safety precautions.

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

 Unplug the refrigerator before making repairs, replacing a light

bulb, or cleaning.

Note: Power to the refrigerator cannot be disconnected by any

setting on the control panel.

Note: Repairs must be performed by a qualified service

professional.

 Replace all parts and panels before operating.

 Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

 Because of potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely

necessary that it be a UL-listed (in the United States) or a

CSA certified (in Canada), 3-wire grounding type appliance

extension cord having a grounding type plug and outlet and

that the electrical rating of the cord be 15 amperes (minimum)

and 120 volts.

 To prevent suffocation and entrapment hazards to children,

remove the fresh food and freezer doors from any refrigerator

before disposing of it or discontinuing its use.

 Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator. They could seriously

injure themselves.

CAUTION

GEAppliances.com

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can

result in fire, explosion, or death.

INSTALLATION

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall

outlet. Do not use an adapter.

The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating

that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded

electrical supply is required. This provides the best

performance and also prevents overloading house

wiring circuits which could cause a fire hazard from

overheated wires.

Never unplug your refrigerator by pulling on the power

cord. Always grip plug firmly and pull straight out from

the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord.

CONNECTING ELECTRICITY

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet

Do not remove the ground prong

Do not use an adapter

Failure to follow these instructions can result in death, fire, or electrical shock.

SAFETY (CONT.)

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

WARNING

Suffocation and child entrapment hazard.

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can result

in child entrapment which can lead to death or brain damage.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the fresh food and freezer doors.

 Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an old

refrigeration product, check with the company

handling the disposal about what to do.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

IMPORTANT:

About the temperature controls.

NOTE: The refrigerator is shipped with

protective film covering the temperature

controls. If this film was not removed

during installation, remove it now.

The temperature controls are preset in the factory at 37°F (3°C) for the

refrigerator compartment and 0°F (-18°C) for the freezer compartment.

Allow 24 hours for the temperature to stabilize to the preset

recommended settings.

Refrigerator temperatures can be adjusted between 34°F and 46°F

(1°C to 8°C), and the freezer temperatures can be adjusted between –6°F

and +8°F (–21°C to –13°C).

To change the Refrigerator temperature:

Tactile-LED Dispenser Control

The temperature controls can display both the SET temperature as well

as the actual temperature in the refrigerator and freezer. The actual

temperature may vary slightly from the SET temperature based on

usage and operating environment.



On some models, setting both controls to the warmest setting until

the display flashes (off) will stop cooling in both the freezer and

refrigerator compartments.



On other models, setting either control to the warmest setting

until the display flashes (off) will stop the cooling to the freezer and

refrigerator.



NOTE: Turning the refrigerator off via the controls on the touch

panel does not shut off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the

temperature controls. If this film was not removed during installation,

remove it now.

Touch-LED Dispenser Control:

To change the temperature, press and release the FREEZER

TEMP/FRIDGE TEMP pad. The SET light will come on and

the display will show the set temperature. To change the

temperature, tap either the

pad until the desired

temperature is displayed.

Once the desired temperature has been set, the temperature

display will return to the actual refrigerator and freezer

temperatures after 5 seconds. Several adjustments may be

required. Each time you adjust the controls, allow 24 hours for

the refrigerator to reach the temperature you have set.

The temperature controls can display both the SET temperature as well

as the actual temperature in the refrigerator and freezer. The actual

temperature may vary slightly from the SET temperature based on

usage and operating environment.

Turning the cooling system off: Tactile-LED Dispenser Control



On some models, setting both controls to the warmest setting until

the display flashes (off) will stop cooling in both the freezer and

refrigerator compartments.



On other models, setting either control to the warmest setting

until the display flashes (off) will stop the cooling to the freezer and

refrigerator.



NOTE: Turning the refrigerator off via the controls on the touch

panel does not shut off electrical power to the refrigerator.

Touch-LED Dispenser Control:

Press and release the FREEZER TEMP/FRIDGE TEMP pad.

Press

to set freezer temperature to 5. The display will

show OFF. To turn the unit back on, press the FREEZER

TEMP/FRIDGE TEMP pad. Press

to set the freezer and

refrigerator temperatures to the preset points of 0°F (-18°C)

for the freezer and 37°F (3°C) for the refrigerator.

When the unit is turned back on, it will take up to 24 hours

to stabilize.

The Performance Air-Flow System is designed to maximize

temperature control in the refrigerator and freezer

compartments. This unique special feature consists of the

Air Tower along the back wall of the refrigerator and the Air

Tunnel on the bottom portion of the freezer rear wall. Placing

food in front of the louvers on these components will not affect

performance. Although the Air Tower and the Air Tunnel can

be removed, doing so will affect temperature performance.

(For removal instructions, on-line, contact us at ge.com or call

800.GE.CARES. In Canada, contact us at geappliances.ca or call

1.800.561.3344.)

Performance Air Flow System

Touch-LED Dispenser Control

Not all features are on all models. Your controls may be similar to the following:

Tactile LED Dispenser Control.

About TurboCool.

™

How it Works

TurboCool

™

rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool

™

when adding

a large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature or

when putting away warm leftovers. It can also

be used if the refrigerator has been without

power for an extended period.

Once activated, the compressor will turn

on immediately and the fans will cycle on

and off at high speed as needed for eight

hours. The compressor will continue to run

until the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle on

and off to maintain this setting. After 8 hours, or

if TurboCool

™

is pressed again, the refrigerator

compartment will return to the original setting.

How to Use

Tactile LED Dispenser Control:

Press TurboCool

™

. The TurboCool temperature

display will show Tc and the LED will be activated.

After TurboCool

™

is complete, the TurboCool

™

indicator light will go out.

NOTES: The refrigerator temperature cannot be

changed during TurboCool

™

The freezer temperature is not affected

during TurboCool

™

When opening the refrigerator door during

TurboCool

™

, the fans will continue to run if

they have cycled on.

Touch-LED Dispenser Controls:

Press SET FEATURES. The refrigerator

temperature display will show TurboCool

™

and/or TC. Press ON/OFF.

After TurboCool

™

is complete, the refrigerator

compartment will return to the original setting.

NOTES:

The refrigerator temperature cannot be changed

during TurboCool

™

The freezer temperature is not affected during

TurboCool

™

When opening the refrigerator door during

TurboCool

™

, the fans will continue to run if they

have cycled on.

About ClimateKeeper2.

™

(on some models)

How it Works

The ClimateKeeper2

™

is the industry’s most

advanced refrigeration system, delivering

optimum temperature and humidity

performance to keep food garden fresh longer

and reduce freezer burn.

The ClimateKeeper2

™

system features two

HYDSRUDWRUV³RQHIRUWKHUHIULJHUDWRUDQGRQH

for the freezer.

This provides two separate cooling systems,

and separates the airflow between the fresh

food and freezer compartments during normal

cooling operations.*

This ensures that the humidity levels in the

fresh food compartment are significantly higher

than in a conventional system,** allowing fresh

produce and other unsealed foods to retain

their moisture content and freshness longer.

Moisture sensitive foods such as fresh fruit,

salads, rice, etc., can now be stored on open

shelves without excessive moisture loss.

Due to the higher humidity in the refrigerator,

you may on occasion experience fog or

small amounts of moisture in the refrigerator

compartment. This is normal and may

come and go as different food loads and

environmental conditions change. Wipe dry

with a paper towel if desired.

The separate airflow system minimizes the

mixing of air between the two compartments,

which reduces fresh food odor transfer to

improve the taste of ice.

The ClimateKeeper2

™

system also reduces

the number of defrosting cycles in the freezer

evaporator, thereby reducing freezer burn.

* Freezer air is used in the CustomCool feature.

** Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2

™

refrigerators versus conventional units.

About Set Features. GEAppliances.com

This pad is used to select the following features:

TurboCool, Quick Ice, Door Alarm and Water

Filter.

Pressing SET FEATURES repeatedly will cycle

through all of the available features and then

exit the mode. If no key is pressed, the mode

will exit and return to displaying features

currently set.

Empty the pan. Place the Chill/Thaw tray in

the pan. Place the items on the tray and

close the pan completely.

Touch LED Dispenser Control:

Select the ExpressThaw

™

, ExpressChill

™

or SelectTemp

™

pad. The display and SET

light will come on. Tap the pad until the light

appears next to the desired setting.

Use the following chart to determine the

best setting to use.



ExpressChill can be set to 15, 30 or 45

minutes. The default is 15 minutes.



To stop a feature before it is finished:

tap that feature’s pad until no options are

selected and the display is off.



During ExpressThaw and ExpressChill, the

display on the controls will count down the

time in the cycle (on some models).



After the ExpressThaw cycle is complete,

the pan will reset to the MEAT setting (32°F

[0°C]) to help preserve thawed items until

they are used.



The displayed actual temperature of the

CustomCool pan may vary slightly from

the SET temperature based on usage and

operating environment.

NOTE: For food safety reasons, it is

recommended that foods be wrapped in plastic

wrap when using ExpressThaw. This will help

contain meat juices and improve thawing

performance.

About CustomCool

™

. (on some models)

The CustomCool

™

feature is used to quickly

chill items, thaw items or hold the pan at a

specific temperature. This feature is a system of

dampers, a fan, a temperature thermistor and

a heater.

The pan is tightly sealed to prevent temperature

fluctuations in the rest of the refrigerator.

The controls for this pan are located on the

dispenser with the temperature controls.

How to Use

ExpressThaw

™

ExpressChill

™

Touch LED Dispenser Control

How it Works

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating them

to the lock position.

How to Remove and Replace the Drawer

About ExpressChill

™

. (on some models) GEAppliances.com

The ExpressChill

™

feature is a system of

dampers, a fan and a temperature thermistor.

The pan is tightly sealed to prevent the pan’s

temperature from causing temperature

fluctuations in the rest of the refrigerator.

The controls for this pan are located in the top

of the refrigerator or on the dispenser with the

temperature controls.

How it Works

Empty the pan. Place the Chill tray in the

pan. Place the items on the tray and close

the pan completely.

Select the ExpressChill

™

pad. On some

models, you can then select the chill time

(use chart to determine best setting). Other

models will only have one option (45

minutes). On models with multiple settings,

tap the pad until the light appears next to

the desired setting.





To stop a feature before it is finished, tap

that feature’s pad until no options are

selected and the display is off.



During ExpressChill, the display on the

controls will count down the time in the

cycle.

How to Use

ExpressChill

™

About CustomCool

™

. (on some models)

CustomCool

™

Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

ExpressThaw

™

0.5 Lb. (4 hours)



Hamburger Patties (0.5 lb)



Individually Wrapped

Filet Mignon (0.5 lb)

1.0 Lb. (6 hours)



Chicken Breasts (1.0 lb)



Ground Beef (1.0 lb)



Steak (1.0 lb)

2.0 Lbs. (10 hours)



Chicken Breasts (2.0 lbs)



Ground Beef (2.0 lbs)



Steak (2.0 lbs)

3.0 Lbs. (12 hours)



Chicken Breasts (3.0 lbs)



Ground Beef (3.0 lbs)



Steak (3.0 lbs)

ExpressChill

™

15 Minutes



1 Beverage Can (12 oz)



2 Small Juice Boxes (6–8 oz each)

30 Minutes



2 to 6 Beverage Cans (12 oz each)



2 Plastic 20 oz Bottles of Beverage



4 to 6 Small Juice Boxes

(6–8 oz each)



3 Foil Juice Packets



Wine (750 ml bottle)

45 Minutes



2 Liter of Beverage



1/2 Gallon of Juice



Gelatin–1 package

SelectTemp

™

Citrus Setting (43°F [6°C])



Oranges, Lemons, Limes, Pineapple,

Cantaloupe



Beans, Cucumbers, Tomatoes,

Peppers, Eggplant, Squash

Produce Setting (35°F [2°C])



Strawberries, Raspberries, Kiwifruit,

Pears, Cherries, Blackberries, Grapes,

Plums, Nectarines, Apples



Asparagus, Broccoli, Corn,

Mushrooms, Spinach, Cauliflower,

Kale, Green Onion, Beets, Onions

Meat Setting (32°F [0°C])



Raw Meat, Fish and Poultry

About the water filter. (on some models) GEAppliances.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right

corner of the refrigerator compartment.

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter

cartridge on the dispenser. This light will turn orange to tell you

that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement

indicator light turns red or if the flow of water to the dispenser or

ice maker decreases.

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every six months or

earlier if the flow of water to the water dispenser or ice maker

decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by

slowly turning it to the left. Do not pull down on the cartridge. A

small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a SmartWater cartridge with an

adapter, it must be removed before installing the cartridge.

To remove the adapter, turn it to the left about 1/4 turn.

If you are replacing a Water by Culligan cartridge, leave the

adapter in place. This adapter will stay in the refrigerator when

you replace future cartridges.

On models without a replacement indicator light, apply the

month and year sticker to the new cartridge to remind you

to replace the filter in six months.

Fill the replacement cartridge with water from the tap to

allow for better flow from the dispenser immediately after

installation.

Line up the arrow on the cartridge and the cartridge holder.

Place the top of the new cartridge up inside the holder. Do

not push it up into the holder.

Slowly turn it to the right until the filter cartridge stops.

DO NOT OVERTIGHTEN. As you turn the cartridge, it will

automatically raise itself into position. The cartridge will

move about 1/2 turn.

Run water from the dispenser 1-1/2 gallons (about three

minutes) to clear the system and prevent sputtering.

Press and hold the WATER FILTER pad (on some models) on

the dispenser for 3 seconds.

NOTE: A newly-installed water filter cartridge may cause water

to spurt from the dispenser upon first use.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and the ice maker will

not operate without the filter or filter bypass plug.

To use the filter bypass plug on Water by Culligan models, you

must first remove the filter adapter from the cartridge holder by

turning it to the left.

For the maximum benefit of your filtration system, GE

recommends the use of GE branded SmartWater filters only.

Using GE branded filters in GE and Hotpoint refrigerators

provides optimal performance and reliability. GE branded

SmartWater filters are always the right choice because they

are patented and designed specifically for GE products. GE

SmartWater filters meet rigorous industry NSF standards for

safety and quality that are important for products that are

filtering your water. GE has not qualified non-GE branded

filters for use in GE and Hotpoint refrigerators and there is no

assurance that non-GE branded filters meet GE’s standards for

quality, performance and reliability.

,I\RXKDYHTXHVWLRQV³YLVLWRXU:HEVLWHDWGEAppliances.com, or

call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States,

visit our Website at GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

See filter label for type of filter to order (MWF or MSWF).

Customers in Canada should consult the yellow pages for the

nearest Mabe Service Center.

Cartridge

Holder

Filter

Bypass

Plug

Filter

Bypass

Plug

SmartWater

Water by Culligan

(appearance may vary)

With adapter Without adapter

Some models

use this type of

water filter.

About the shelves and bins.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Bins

The larger refrigerator door bins and freezer

tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up,

then lift up and out.

To replace or relocate: Engage the back side

of the bin in the molded supports on the door.

Then push down on the front of the bin. Bin will

lock in place.

The snugger helps prevent tipping, spilling or

sliding of small items stored on the door shelf.

Place a finger on either side of the snugger

near the rear and move it back and forth

to fit your needs.

Top Freezer Bins

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

QuickSpace

™

Shelf

This shelf splits in half and slides under itself for

storage of tall items on the shelf below.

This shelf can be removed and replaced or

relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf cannot be used in

the lowest position.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to

reach items stored behind others. The special

edges are designed to help prevent spills from

dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the shelf

straight out.

To replace or relocate:

Line the shelf up with the supports and slide

it into place. The shelf can be repositioned

when the door is at 90° or more. To reposition

the shelf, slide the shelf past the stops and

angle downward. Slide shelf down to the

desired position, line up with the supports and

slide into place.

Make sure you push the shelves all the way

back in before you close the door.

Press tab and pull shelf forward

to remove

Top freezer bin

Do not block

NOTE:

Be careful when

placing items in

the top bin. Make

sure that items

do not block or

fall into the ice

chute.

Top freezer bin (on some models)

Do not block

NOTE:

Part must be in

place as shown

for proper ice

dispensing. Food

cannot be stored

in this location.

Not all features are on all models.

Slide-Out Freezer Shelves

To remove, slide out to the stop position, lift the

front past the stop position and slide out.

Make sure you push the shelves all the way

back in before you close the door.

Freezer Baskets

To remove, push the basket all the way to the

back of the freezer. Lift up until the back pins

are disengaged. Lift the entire basket up and

pull out.

Make sure you push the baskets all the way

back in before you close the door.

Fixed Freezer Shelves

There are two types of fixed freezer shelves.

To remove this type of shelf:

Lift the shelf up at the left side.

Bring the shelf out.

To remove this type of shelf:

Lift up the left side of the shelf and slide it

left into the center of the shelf supports.

Rotate the right side of the shelf up and out

of the shelf supports.

NOTE FOR DISPENSER MODELS: In order to

take full advantage of the tilt-out ice bin, only

store items on the shelf below the ice bin that

are no taller than the lowest point on the bin.

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans or one bottle of

wine.

The rack hangs from the sides of the dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin, lift the

front straight up, then lift up and out.

To detach the rack from the dairy bin, pull

the rack’s side wires out of the holes on

each side of the dairy bin.

To replace:

Reattach the rack to the sides of the bin.

Engage the back side of the bin in the

molded supports on the door. Then push

down on the front of the bin. The bin will

lock into place.

GEAppliances.com

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different than

the ones you are used to. The special door

opening/closing feature makes sure the doors

close all the way and are securely sealed.

When opening and closing the door, you will

notice a stop position. If the door is opened

past this stop point, the door will remain open

to allow you to load and unload food more

easily. When the door is only partially open, it

will automatically close.

The resistance you feel at the stop position will

be reduced as the door is loaded with food.

When the door is only partially open,

it will automatically close.

Beyond this stop the door will stay

open.

Door Alignment

If doors are uneven, adjust the refrigerator

door.

Using a 7/16” wrench, turn the door

adjusting screw to the right to raise the

door, to the left to lower it. (A nylon plug,

imbedded in the threads of the pin,

prevents the pin from turning unless a

wrench is used.)

After one or two turns of the wrench,

open and close the refrigerator door and

check the alignment at the top of the

doors.

7/16” Wrench

Raise

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling the

drawer straight out and lifting the drawer up

and over the stop location.

If the door prevents you from taking out the

drawers, first try to remove the door bins.

If this does not offer enough clearance, the

refrigerator will need to be rolled forward

until the door opens enough to slide the

drawers out. In some cases, when you roll the

refrigerator out, you will need to move the

refrigerator to the left or right as you roll it out.

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in

the bottom of the drawers should be

wiped dry.

On some models, the bottom drawer has

full extension slides that allow full access

to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the HI setting to

provide high humidity recommended for most

vegetables.

Slide the control all the way to the LO

setting to provide lower humidity levels

recommended for most fruits.

Convertible Deli Pan

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or fresh food

compartment to flow to the pan.

The variable temperature control regulates

the air flow from the Climate Keeper Air Tower.

Set the control to the coldest setting to store

fresh meats.

Set the control to cold to convert the pan

to normal refrigerator temperature and provide

extra vegetable storage space.

The cold air duct is turned off. Variable settings

between these extremes can

be selected.

About the automatic ice maker.

Automatic Ice maker

7KHLFHPDNHUZLOOSURGXFHVHYHQFXEHVSHUF\FOH³

approximately 100–130 cubes in a 24-hour period, depending

on freezer compartment temperature, room temperature,

number of door openings and other use conditions.

If the refrigerator is operated before the water connection is

made to the ice maker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply,

set the power switch to the ON position.

The ice maker will fill with water when it cools to 15°F (–10°C).

A newly installed refrigerator may take 12 to 24 hours to begin

making ice cubes.

You will hear a buzzing sound each time the ice maker fills with

water.

Throw away the first few batches of ice to allow the water line

to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the ice maker will

stop producing ice. It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes will become cloudy,

taste stale and shrv

CAUTION

Avoid contact with the moving parts of

the ejector mechanism, or with the heating element (located

on the bottom of the ice maker) that releases the cubes.

Do not place fingers or hands on the automatic ice making

mechanism while the refrigerator is plugged in.

Special note about dispenser models:

 Some models have a tilt-out ice bin. The bin can be tilted out

as shown in the illustrations, and it will hold itself up while you

take ice out or turn the ice maker power switch on and off. Be

sure to put the bin back in place before closing the door.

 To restore your ice level from an empty bucket stage, the

following steps are recommended:

12 hours after the first batch of ice has fallen into the bin,

dispense 3 to 4 cubes.

After an additional 6 hours, dispense 3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of

time.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Ice maker

Feeler Arm

Power

Switch

(on some models)

Ice maker

Feeler Arm

Power

Switch

Green

Power Light

(on some models)

NOTE:

In homes with lower than average water pressure, you

may hear the ice maker cycle multiple times when making

one batch of ice.

About the automatic ice maker. (cont) GEAppliances.com

Removing Ice Bin (dispenser models)

CAUTION

The ice bin is heavy when full.

Set the power switch to the OFF position before removing the

bin.

When replacing the bin, be sure to press it firmly into place. If

it does not go all the way back, remove it and rotate the drive

mechanism 1/4 turn. Then push the bin back again.

Rotate

Drive

Mechanism

Dispenser Models only

Lift the bin, then pull it forward

until the bin stops.

Lower the bin to access ice or

reach the power switch.

Models with tilt out ice bin

To access ice and reach the icemaker power switch:

Accessing Ice and Reaching the Power Switch on

Dispenser Models

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not.

Special note for models with tilt-out ice bin:

 These models have a tilt-out ice bin. The bin can be tilted

out as shown in the illustrations, and it will hold itself up

while you take ice out or turn the icemaker power switch

on and off. Be sure to put the bin back in place before

closing the door.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items

on the shelf below the ice bin that are no taller than the lowest point on the

bin.

To access ice, pull the bin forward.

To reach the power switch, pull the

shelf straight out. Always be sure to

replace the shelf.

Models with a shelf above the ice bin

Shelf

Ice Bin

Shelf

Ice Bin

Pull the bin forward until the

bin stops.

Lower the bin to access ice or

reach the power switch.

On some models, to access ice or reach the power switch:

Select CUBED, CRUSHED or WATER.

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce

water spotting, the shelf and its grille should be

cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water

line and to fill the water system. To flush out

impurities in the water line, throw away the first

six glassfuls of water.

CAUTION

Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK or LOCK CONTROLS pad for 3

seconds to lock the dispenser and control panel.

To unlock, press and hold the pad again for 3

seconds.

Dispenser Light

The LIGHT pad turns the light in the dispenser

on and off. The light also comes on when the

dispenser cradle is pressed. For models with a

bulb, if the light burns out, it should be replaced

with a 6 watt 12V maximum bulb. For LED

models contact Factory Service.

Door Alarm

Use Door Alarm to sound if either door is open

for more than 3 minutes. The alarm will stop

once the door is closed. For LCD models, a popup

screen will appear. The alarm can be silenced by

touching the LCD screen.

Touch LED Dispenser Control:

Press the SET FEATURES pad once and DOOR

ALARM will blink. Press ON/OFF and the door

alarm will be set and the icon will turn solid. Press

ON/OFF again to turn the alarm off.

Door Alarm (on Tactile LED Dispenser Control

model)

To set the alarm, press this pad until the indicator

light comes on. This alarm will sound if either

door is open for more than 3 minutes. The light

goes out and the beeping stops when you close

the door.

About the ice and water dispenser. (on some models)

To Use the Dispenser

Spill Shelf

Quick Ice

When you need to speed up ice production, use the

Quick Ice feature. While this feature is turned on,

the freezer fan runs continuously for 48 hours, or

until the feature is turned OFF. During this period, ice

production will increase up to 40%. Models with the

integrated ice feature system require at FIRST USE at

least half an 8 oz. glass of ice to be dispensed every 6

to 12 hours. This will help the ice maker fill the bucket

properly so that dispensing is better.

How to Use

Touch LED Dispenser Control:

Press the SET FEATURES pad twice and QUICK ICE

will blink. Press ON/OFF to turn the feature on, then

again to turn it off.

Quick Ice (on Tactile LED Dispenser Control

model)

When you need ice in a hurry, press this pad

to speed up ice production. This will increase

ice production for the following 48 hours or

until you press the pad again.

GEAppliances.com

Precise Fill (on some models)

This water dispenser is equipped with a feature

called “precise fill.” This feature allows you to choose

a precise amount of water (cups or ounces) that

you would like dispensed. Pints and Liters are also

available for LCD models.

Touch LED Dispenser Control

Press the PRECISE FILL CUPS/OZ pad. The

WATER pad will light and the CRUSHED and

CUBED ice pads will turn off. The last unit used

will be displayed.

Press the PRECISE FILL pad again to toggle

between cups and ounces.

If you selected OUNCES, press the

pad to

select the number of ounces you would like to have

dispensed between 2–99 ounces. The default is 8

ounces.

If you selected CUPS, press the

pad to

select the amount you would like to have dispensed.

They are displayed as 1/4, 1/3, 1/2, 2/3 and 3/4, with

the highest amount being 16 3/4 cups. The default

is 1 cup.

Press the cup against the cradle and water will

begin dispensing. It will automatically stop when

the amount set has been dispensed. The display

will show the amount of water dispensed, beep,

then reset after 5 seconds.

NOTE: Do not leave the dispenser unattended when

water is being dispensed.

If you would like to stop dispensing water

before the specified amount has been

dispensed, just remove the cup from the cradle.

The display will show the amount that has been

dispensed for 5 seconds. If the cup switch is

pressed again within that time, the dispenser

will continue up to the set amount. If not, the

display will return to the set amount.

Important Facts About Your Dispenser



Do not add ice from trays or bags to

the storage drawer. It may not crush or

dispense well.



Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam

the chute or cause the door in the chute

to freeze shut. If ice is blocking the chute,

poke it through with a wooden spoon.



Beverages and foods should not be

quick-chilled in the ice storage drawer.

Cans, bottles or food packages in the

storage drawer may cause the ice maker

or auger to jam.



To keep dispensed ice from missing the

glass, put the glass close to, but not

touching, the dispenser opening.



Some crushed ice may be dispensed

even though you selected CUBED. This

happens occasionally when a few cubes

accidentally get directed to the crusher.



After crushed ice is dispensed, some

water may drip from the chute.



Sometimes a small mound of snow will

form on the door in the ice chute. This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly. The snow will eventually

evaporate.

Cleaning the Outside

The dispenser drip area, beneath the grille,

should be wiped dry. Water left in this area

may leave deposits. Remove the deposits by

adding undiluted vinegar to the well. Soak

until the deposits disappear or become loose

enough to rinse away.

The dispenser cradle. Before cleaning, lock

the dispenser by pressing and holding the

LOCK or LOCK CONTROLS pad for 3 seconds.

Clean with warm water and baking soda

VROXWLRQ³DERXWDWDEOHVSRRQPORI

baking soda to a quart (1 liter) of water. Rinse

thoroughly and wipe dry.

The door handles and trim. Clean with a

cloth dampened with soapy water. Dry with

a soft cloth.

The stainless steel doors and door handles

(on some models) can be cleaned with

a commercially available stainless steel

cleaner. Cleaners with oxalic acid such

as Bar Keepers Friend Soft Cleanser™ will

remove rust, tarnish and small blemishes.

Use only a liquid cleanser free of grit and

rub in the direction of the brush lines with a

damp soft sponge.

Do not use appliance wax or polish on the

stainless steel.

Keep the outside clean. Wipe with a

clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled

dish cloth or wet towel. These may leave

a residue that can erode the paint. Do not

use scouring pads, powdered cleaners,

bleach or cleaners containing bleach

because these products can scratch and

weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If

this is not practical, wring excess moisture

out of sponge or cloth when cleaning around

switches, lights or controls.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³

about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than

that which is recommended, especially

those that contain petroleum distillates,

can crack or damage the interior of the

refrigerator.

CAUTION

Do not clean glass

shelves or covers with warm water

when they are cold. Glass shelves and

covers may break if exposed to sudden

temperature changes or impact such as

bumping or dropping. Tempered glass is

designed to shatter into many small pieces

if it breaks.

Do not wash any plastic refrigerator parts

in the dishwasher.

The chill/thaw tray is dishwasher safe.

Dispenser drip area.

Care and cleaning of the refrigerator.

GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator away

from the wall. All types of floor coverings can

be damaged, particularly cushioned coverings

and those with embossed surfaces.

Pull the refrigerator straight out and return it

to position by pushing it straight in. Moving the

refrigerator in a side direction may result in

damage to the floor covering or refrigerator.

When pushing the refrigerator back, make

sure you don’t roll over the power cord or ice

maker supply line.

For long vacations or absences, remove food

and unplug the refrigerator. Clean the interior

with a baking soda solution of one tablespoon

(15 ml) of baking soda to one quart (1 liter) of

water. Leave the doors open.

Set the ice maker power switch to the O (off)

position and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water supply

system to prevent serious property damage

due to flooding.

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place to

prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back of the

refrigerator against the hand truck. This could

damage the refrigerator. Handle only from the

sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Replacing the light bulbs.(on some models)

5HIULJHUDWRU&RPSDUWPHQW³8SSHU/LJKW

Unplug the refrigerator.

The bulbs are located at the top of the

compartment, inside the light shield. On some

models, a screw at the front of the light shield

will have to be removed. On other models, the

screw is located in the pocket located at the

back of the light shield.

To remove the light shield, on some models,

press in on the tabs on the sides of the shield

and slide forward and out. On other models,

just slide the shield forward and out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the light shield and screws (on some models).

When replacing the light shield, make sure

that the tabs at the back of the shield fit into

the slots at the back of the light shield

housing.

Plug the refrigerator back in.

5HIULJHUDWRU&RPSDUWPHQW³/RZHU/LJKW

This light is located above the top drawer.

Unplug the refrigerator.

Remove the convertible meat drawer

control knob by pulling straight out.

Lift the light shield up and pull it out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the shield and the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light shield.

(The shelf will be easier to remove if it is

emptied first.) On some models, a screw at

the top of the light shield will need to be

removed.

To remove the light shield, press in on the

sides, and lift up and out.

Replace the bulb with an appliance bulb

of the same or lower wattage, and

reinstall the light shield. When

reinstalling the light shield, make sure

the top tabs snap securely into place.

Replace the screw (on some models).

Reinstall the shelf and plug the

refrigerator back in.

Tabs

Pocket

Your light shield will look like

one of the following:

WARNING

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

live wire filament. (A burned-out light bulb may break when being replaced.)

Turning the control to the OFF position does not remove power to the light circuit.

La page charge ...

GE PZS22MSKSS Guide d'installation

Marque: GE

Modèle: PZS22MSKSS

Catégorie: Frigos

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE PZS22MSKSS Installation guide
español: GE PZS22MSKSS Guía de instalación

GE PZS22MSKSS Guide d'installation

GE PZS22MSKSS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents