Ricoh Aficio SG 3100SNw Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

1
Notes for Wireless LAN Users
This manual explains how to connect the machine to the network via a wireless LAN interface.
Ad hoc mode is not supported.
Ethernet and wireless LAN settings cannot be enabled at the same time.
Checking Your Wireless Network Environment
Before configuring the wireless LAN settings, configure the machine's IP address.
For details about configuring the machine's IP address, see "2. Preparing for Printing", User
Guide .
Check that the access point is operating.
CHV600
• Plug the wireless LAN cable into the Ethernet port before configuring the wireless LAN set-
tings.
CHV601
2
Change the [LAN Type] to [IEEE 802.11b/g/n] before configuring the wireless LAN settings.
the [User Tools] key
[Login] Enter the login password. (default: 000000) [System Settings]
[Interface Settings] [Network] [LAN Type] [IEEE 802.11b/g/n] Turn the machine off.
Turn the machine on.
CHV632
3
Selecting the Configuration Method
The configuration method depends on the access point being used.
"Easy Setup" is a function for automatically configuring the wireless LAN settings. The actual
name of the function may vary depending on the access point being used. See the access point
manual.
Page 4
”Easy Setup Using the
WPS Button”
Page 8
”Manual setting”
Easy Setup
“PBC Method”
Easy Setup
“PIN Method”
Manual setting
Does the access point support "Easy Setup" of the wireless LAN?
Is there a push button
on the access point?
Page 6
”Easy Setup Using a
PIN Code”
Yes
No
Yes No
CHV604
Manual setting: Page 8 "Configuring Settings Using Web Image Monitor"
Manual setting: Page 17 "Configuring Settings Using the Control Panel"
4
Easy Setup Using the WPS Button
1. Turn the machine on.
CHV605
2. Press the [User Tools] key.
CHV051
3. Press [Login].
4. Enter the login password, and then press the [OK] key.
If this is the first time to log in, enter the default password of "000000".
5. Press the [
] or [ ] key to display [System Settings], and then press the [OK] key.
6. Press the [
] or [ ] key to display [Interface Settings], and then press the [OK] key.
7. Press the [
] or [ ] key to display [IEEE 802.11], and then press the [OK] key.
8. Press the [
] or [ ] key to display [Easy Setup], and then press the [OK] key.
1/1
IEEE
802.11 b/g/n
Det. Settings
Easy Setup
Current status
5
9. Press the WPS button on the access point.
WPS
CHV607
10. Press the [ ] or [ ] key to display [PBC Method], and then press the [OK] key.
1/1
Easy Setup:
PIN Method
PBC Method
If the connection is successful, "Connection to AP has succeeded." will be displayed.
If the connection fails, "Connection to AP has failed." is displayed. If this is the case, go back
to Step 8. If the problem persists, check whether the access point is working properly. If the
access point is working properly but the problem still persists, contact your sales or service
representative.
If the access point cannot be detected within 120 seconds, the search session expires.
6
Easy Setup Using a PIN Code
1. Turn the machine on.
CHV605
2. Press the [User Tools] key.
CHV051
3. Press [Login].
4. Enter the login password, and then press the [OK] key.
If this is the first time to log in, enter the default password of "000000".
5. Press the [
] or [ ] key to display [System Settings], and then press the OK key.
6. Press the [
] or [ ] key to display [Interface Settings], and then press the OK key.
7. Press the [
] or [ ] key to display [IEEE 802.11], and then press the OK key.
8. Press the [
] or [ ] key to display [Easy Setup], and then press the OK key.
1/1
IEEE
802.11 b/g/n
Det. Settings
Easy Setup
Current status
7
9. Press the [ ] or [ ] key to display [PIN Method], and then press the OK key.
1/1
Easy Setup:
PIN Method
PBC Method
10. Check the machine's PIN.
PIN Method:
Connect
11. Enter the machine's PIN on the access point web page.
CHV609
For details, see the manual supplied with the wireless LAN access point.
12. Execute WPS (PIN system) from the access point's web page.
13. Press [Connect].
If the connection is successful, "Connection to AP has succeeded." will be displayed.
If the connection fails, “Connection to AP has failed.” is displayed. If this is the case, go back
to Step 10. If the problem persists, check whether the access point is working properly. If the
access point is working properly but the problem still persists, contact your sales or service
representative.
8
Manual Setting
If you cannot confirm the settings of the access point being used or the access point does not
support WPS, configure the wireless LAN settings manually.
You can configure the settings using Web Image Monitor or the control panel. This manual mainly
explains configuration using Web Image Monitor.
Configuring Settings Using Web Image Monitor
Connect the machine and computer with an Ethernet cable before configuring the settings.
CHV619
Check the security method employed by the access point being used.
Change the [LAN Type] to [Ethernet] before configuring the wireless LAN settings.
CHV632
the [User Tools] key [Login] Enter the login password. (default: 000000) [System Settings]
[Interface Settings] [Network] [LAN Type] [Ethernet] the [OK] key Turn the machine
off. Turn the machine on.
9
Check the machine's IP address.
1
2
CHV654
the [User Tools] key (1) [System Settings] [Interface Settings] [Network] [Machine IPV4
Address] [IP Add.] the [Escape] key (2) The control panel returns to the initial screen.
1/1
Mach.IPv4 Addr. :
Specify
Auto-Obtain(DHCP)
IP Add. Subnet M MAC Add.
10
1. Launch the Web browser.
2. In the address bar, enter "http://(machine's IP address or host name)/".
3. Enter the administrator password, and then click [Login].
If this is the first time to log in, enter the default password of "000000".
CHV636
4. In the menu area, click [Configuration].
CHV638
11
5. Click [Interface Settings] under "Interface".
CHV640
1
2
CHV644
1. Select [Wireless LAN].
2. Click [OK].
12
6. Click [OK], when "Update complete" appears.
7. Click [Wireless LAN Settings] under "Interface".
CHV640
If not applying any security method
3
1
2
CHV646
1. Enter the network name of the access point.
2. Select [Inactive].
3. Click [OK].
13
If the security method is WEP
1
2
3
4
CHV648
1. Enter the network name of the access point.
2. Select [WEP].
3. Enter the password for the access point.
Configure other settings if needed.
4. Click [OK].
14
If the security method is WPA-PSK
1
2
6
3
4
5
CHV650
1. Enter the network name of the access point.
2. Select [WPA-PSK].
3. Select [WPA(TKIP)], [WPA(AES)],or [WPA2(AES)].
4. Select [Passphrase] or [Hex].
5. Enter the password for the access point.
6. Click [OK].
15
If the security method is WPA-EAP
1
2
4
5
3
CHV652
1. Enter the network name of the access point.
2. Select [WPA-EAP].
3. Select [WPA(TKIP)], [WPA(AES)],or [WPA2(AES)].
4. Select the extensible authentication protocol you want to use.
Enter the user ID for Extensible Authentication Protocol (EAP).
Enter the user name to be used for RADIUS server authentication.
Enter the password to be used for RADIUS server authentication.
Configure other settings if needed.
5. Click [OK].
16
8. Click [OK], when "Update complete" appears.
9. Click [Logout].
CHV642
10. Turn the machine off.
11. Remove the Ethernet cable, and then connect the wireless LAN cable.
CHV601
12. Turn the machine on.
Setting is complete.
17
Configuring Settings Using the Control Panel
Change the [LAN Type] to [IEEE 802.11b/g/n] before configuring the wireless LAN settings.
For details, see "2. Preparing for Printing", User Guide .
CHV632
1. Change the network interface settings.
the [User Tools] key [Login] Enter the login password. (default: 000000) [System Set-
tings] [Interface Settings] [Network] [LAN Type] [IEEE 802.11b/g/n] the [OK] key
Turn the machine off. Turn the machine on.
2. Configure the wireless LAN settings.
the [User Tools] key
[Login] Enter the login password. (default: 000000) [System Set-
tings] [Interface Settings] [IEEE 802.11] [Det. Settings] the [OK] key Turn the machine
off. Turn the machine on.
18
Checking the Status
CHV632
the [User Tools] key [System Settings] [Interface Settings] [IEEE 802.11] [Current status]
[Status]
19
Hinweise für Wireless LAN-Anwender
In diesem Handbuch wird beschrieben, wie das Gerät über die WLAN-Schnittstelle an das Netz-
werk angeschlossen werden kann.
Ad-hoc-Modus wird nicht unterstützt.
Ethernet- und Wireless-LAN-Einstellungen können nicht gleichzeitig aktiviert sein.
Überprüfen der Wireless-Netzwerkumgebung
Vor der Konfiguration der Wireless-LAN-Einstellungen müssen Sie die IP-Adresse des Gets
konfigurieren.
Einzelheiten zur Konfiguration der IP-Adresse des Geräts finden Sie in der Anwenderanleitung
.
Prüfen Sie, ob der Zugriffspunkt arbeitet.
CHV600
Vor der Konfiguration der Wireless-LAN-Einstellungen müssen Sie das Wireless-LAN-Kabel
mit dem Ethernet-Anschluss verbinden.
CHV601
20
Ändern Sie den [LAN-Typ] auf [IEEE 802.11b/g/n], bevor Sie die Wireless-LAN-Einstellungen
konfigurieren.
Taste [Anwenderprogramm] [Login] Login-Passwort eingeben. (Standard: 000000)
[Systemeinstell.] [Schnittstelleneinst.] [Netzwerk] [LAN-Typ] [IEEE 802.11b/g/n]
Gerät ausschalten.
Gerät einschalten.
CHV632
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128

Ricoh Aficio SG 3100SNw Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à