LG DLGX8001V Le manuel du propriétaire
- Catégorie
- Sèche-linge
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
OWNER’S MANUAL
DRYER
Please read this owner’s manual thoroughly before operating and
keep it handy for reference at all times.
MFL62512881
ENGLISH FRANÇAIS
DLEX8000* DLGX8001*
www.lg.com
Copyright © 2012 - 2017 LG Electronics Inc. All Rights Reserved.
MFL62512881_en_170329.indd 1 2017.3.29 2:22:32 PM
2
TABLE OF CONTENTS
3
IMPORTANT SAFETY INSTRUCTIONS
3 WHAT TO DO IF YOU SMELL GAS
4 BASIC SAFETY PRECAUTIONS
5 GROUNDING INSTRUCTIONS
5 SAFETY INSTRUCTIONS FOR INSTALLATION
6 SAFETY INSTRUCTIONS FOR STEAM
FUNCTIONS
7 SAFETY INSTRUCTIONS FOR CONNECTING
ELECTRICITY
8 SPECIAL FEATURES
9
INTRODUCING YOUR DRYER
9 Parts
9 Accessories
10 Control Panel Features
11 Time and status display
12
INSTALLATION INSTRUCTIONS
12 Installation steps
13 Installation Location Requirements
13 Clearances
15 Installation with Optional Pedestal Base or
Stacking Kit
16 Leveling the dryer
17 To remove the door
18 To install the door
19 Changing the dryer vent location
20 Venting requirement
22 Connecting gas dryers
24 Connecting electric dryers
25 Special requirements for manufactured or
mobile homes
25 Final installation check
26 Installation test (Exhaust check)
28
HOW TO USE
28 Operating the dryer
29 Cycle guide
30 Sorting load
30 Loading the dryer
30 Check the lint filter before every load
31 Cycle setting buttons
32 Special functions
33 Custom program
33 Steam functions
35 Steam cycle guide
36
MAINTENANCE
36 Regular Cleaning
37
TROUBLESHOOTING
37 Before Calling for Service
40
SPECIFICATIONS
41
USING SMARTDIAGNOSIS
TM
42
OPTIONAL ACCESSORIES
42 Stacking Kit Installation
44
WARRANTY
TABLE OF CONTENTS
MFL62512881_en_170329.indd 2 2017.3.29 2:22:32 PM
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.
These words mean:
w
DANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
w
WARNING
You can be killed or seriously injured if you don’t follow instructions.
w
CAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is
installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with
clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These
conditions will obstruct clothes dryer airflow and increase the risk of fire.
• Install the clothes dryer according to the manufacturer’s instructions and local codes.
• Save these instructions.
w
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
w
IMPORTANT SAFETY INSTRUCTIONS
MFL62512881_en_170329.indd 3 2017.3.29 2:22:33 PM
4
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
BASIC SAFETY PRECAUTIONS
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
described in this manual.
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
in, washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
part is moving.
or attempt any servicing unless specifically
recommended in this owner’s manual or in published
user-repair instructions that you understand and have
the skills to carry out.
remove the door to the drying compartment.
supervision of children is necessary when the dryer is
used near children.
static unless recommended by the manufacturer of
the fabric softener or product.
or similarly textured rubber-like materials.
surrounding areas free from the accumulation of lint,
dust, and dirt.
cleaned periodically by qualified service personnel.
exposed to the weather.
objects.
Do not store plastic, paper, or clothing that may
burn or melt on top of the dryer during operation.
IMPORTANT SAFETY INSTRUCTIONS
MFL62512881_en_170329.indd 4 2017.3.29 2:22:33 PM
5
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
w
WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or service person if you are in doubt that the appliance is properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
Properly ground dryer to conform with all
governing codes and ordinances. Follow details in
the installation instructions. Electric shock can result if
the dryer is not properly grounded.
Before use, the dryer must be properly installed as
described in this manual. Electric shock can result if
the dryer is not properly grounded.
Install and store the dryer where it will not be
exposed to temperatures below freezing or
exposed to the weather.
All repairs and servicing must be performed
by an authorized servicer unless specifically
recommended in this owner’s manual. Use only
authorized factory parts. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
To reduce the risk of electric shock, do not install
the dryer in humid spaces. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
Connect to a properly rated, protected, and sized
power circuit to avoid electrical overload. Improper
power circuit can melt, creating electric shock and/or
fire hazard.
Remove all packing items and dispose of all
shipping materials properly. Failure to do so can
result in death, explosion, fire, or burns.
Place dryer at least 18 inches above the floor for
a garage installation. Failure to do so can result in
death, explosion, fire, or burns.
Keep all packaging from children. Packaging
material can be dangerous for children. There is a risk
of suffocation.
Do not install near another source of heat such as
a stove, cooking oven. Failure to do so can cause
deform, smoke and fire.
Do not place candles, smoking materials, or other
flammables on top of the product. Dripping wax,
smoke, or fire can result.
Remove all protective vinyl film from the product.
Failure to do so can cause product damage, smoke or
fire.
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least
resistance for electric current. This appliance must be
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided with the appliance. If
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or
lead on the appliance.
Electric shock can result if the dryer is not properly
grounded.
IMPORTANT SAFETY INSTRUCTIONS
MFL62512881_en_170329.indd 5 2017.3.29 2:22:33 PM
6
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
w
WARNING
To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long
sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property
damage, injury to persons, or death.
Exhaust/Ducting:
SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
Gas dryers MUST be exhausted to the outside.
Failure to follow these instructions can result in fire or
death.
The dryer exhaust system must be exhausted
to the outside of the dwelling. If the dryer is not
exhausted outdoors, some fine lint and large
amounts of moisture will be expelled into the
laundry area. An accumulation of lint in any area of
the home can create a health and fire hazard.
Use only rigid metal or flexible metal 4-inch
diameter ductwork inside the dryer cabinet or for
exhausting to the outside. Use of plastic or other
combustible ductwork can cause a fire. Punctured
ductwork can cause a fire if it collapses or becomes
otherwise restricted in use or during installation.
Ductwork is not provided with the dryer, and you
should obtain the necessary ductwork locally. The
end cap should have hinged dampers to prevent
backdraft when the dryer is not in use. Failure to
follow these instructions can result in fire or death.
The exhaust duct must be 4 inches (10.2 cm) in
diameter with no obstructions. The exhaust duct
should be kept as short as possible. Make sure
to clean any old ducts before installing your new
dryer. Failure to follow these instructions can result in
fire or death.
Rigid or semi-rigid metal ducting is recommended
for use between the dryer and the wall. In special
installations when it is impossible to make a
connection with the above recommendations, a UL-
listed flexible metal transition duct may be used
between the dryer and wall connection only. The
use of this ducting will affect drying time. Failure to
follow these instructions can result in fire or death.
DO NOT use sheet metal screws or other fasteners
which extend into the duct that could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. For complete details, follow
the Installation Instructions. Failure to follow these
instructions can result in fire or death.
w
WARNING
Fire Hazard
Failure to follow safety warnings exactly could result
in serious injury, death or property damage.
Do not install a booster fan in the exhaust duct.
Install all clothes dryers in accordance with the
installation instructions of the manufacturer of the
dryer.
IMPORTANT SAFETY INSTRUCTIONS
Do not open the dryer door during steam cycles.
Failure to follow these instructions can result in a burn
hazard.
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, or other flammable
or explosive substances as they give off vapors
that could ignite or explode. Failure to follow these
instructions can result in fire or death.
Do not fill the steam feeder with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances. Failure to follow these instructions can
result in fire or death.
Do not touch the steam nozzle in the drum during
or after the steam cycle. Failure to follow these
instructions can result in a burn hazard.
Do not fill the steam feeder with hot water (over 86
˚F/30 ˚C). Failure to follow these instructions can result
in a burn hazard.
MFL62512881_en_170329.indd 6 2017.3.29 2:22:33 PM
7
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
SAVE THESE INSTRUCTIONS
Do not, under any circumstances, cut or remove
the ground prong from the power cord. To prevent
injury to persons or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
For personal safety, this dryer must be properly
grounded. Failure to do so can result in electric shock
or injury.
Refer to the installation instructions in this manual
for specific electrical requirements for your model.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
This dryer must be plugged into a properly
grounded outlet. Electric shock can result if the
dryer is not properly grounded. Have the wall
outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
The dryer should always be plugged into its own
individual electrical outlet which has a voltage
rating that matches the rating plate. This provides
sparkling performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
Never unplug your dryer by pulling on the power
cord. Always grip plug firmly and pull straight out
from the outlet. The power cord can be damaged,
resulting in a risk of fire and electric shock.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end. The power cord can
melt, creating an electric shock and/or fire hazard.
When installing or moving the dryer, be careful not
to pinch, crush, or damage the power cord. This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
IMPORTANT SAFETY INSTRUCTIONS
MFL62512881_en_170329.indd 7 2017.3.29 2:22:34 PM
8
SPECIAL FEATURES
LARGEST PREMIUM SIZE
The ultra-large stainless steel drum offers superior durability.
EASY-ACCESS REVERSIBLE DOOR
The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to adjust
for installation location.
STEAM FUNCTIONS
LG’s steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static,
and make ironing easier. Simply select the Steam Fresh™ cycle, or you can add a Steam option to selected cycles.
FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The FLOW SENSE™ duct blockage sensing system detects and alerts you to restrictions in the installed household
ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove
ducts.
Smart Diagnosis™
Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your
telephone to the Customer Information Center. The call center agent records the data transmitted from your
machine and uses it to analyze the issue, providing a fast and effective diagnosis.
EASY-TO USE CONTROL PANEL
Rotate the cycle selector knob to select the desired dry cycle. Add cycle options or adjust settings with the touch
of a button.
Protocol P154
Sanitization Performance of
Residential Clothes dryer
C
E
R
T
I
F
I
E
D
D
E
S
I
G
N
SPECIAL FEATURES
MFL62512881_en_170329.indd 8 2017.3.29 2:22:34 PM
9
ENGLISH
INTRODUCING YOUR DRYER
Parts
Accessories
NOTE
responsible for product malfunction or accidents caused by the use of separately purchased unauthorized
components or parts.
subject to change by the manufacturer without prior notice for product improvement purposes.
Included accessories
Drying rack
Optional accessories
Pedestal
(sold separately)
Stacking kit
(sold separately)
Control
panel
Leveling
feet
Lint filter
Power Cord
Location
(Gas
Models)
Gas
Connection
Location
(Gas Models)
Terminal
Block
Access
Panel
(Electric
Models)
Exhaust
Duct
Outlet
Reversible
door
INTRODUCING YOUR DRYER
MFL62512881_en_170329.indd 9 2017.3.29 2:22:37 PM
10
Control Panel Features
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
Button Description
POWER ON/OFF BUTTON
y
- Press to turn the dryer ON or OFF. Pressing the POWER button during a cycle
will cancel that cycle and any settings will be lost.
CYCLE SELECTOR KNOB
y
- Turn this knob to select the desired cycle. Once the desired cycle has been
selected, the standard presets will be shown in the display. On MANUAL DRY
cycles, these settings can be adjusted using the cycle setting buttons anytime
before starting the cycle.
START/PAUSE BUTTON
y
- Press this button to START the selected cycle. If the dryer is running, use this
button to PAUSE the cycle without losing the current settings.
NOTE :
minutes, the dryer turns off automatically.
MORE TIME/LESS TIME BUTTONS
y
- To adjust the drying time, use these buttons with MANUAL DRY, TIME DRY, and
STEAM FRESH™ cycles, as well as the REDUCE STATIC and EASY IRON options.
Press the MORE TIME button to increase the selected manual cycle time by a
CYCLE SETTING BUTTONS
y
- Use these buttons to adjust the settings for the selected cycle.
OPTION BUTTONS
y
- The OPTION buttons allow you to select additional cycle options. Not all
settings are available for all cycles. Refer to the CYCLE GUIDE section of the
manual.
STEAM FUNCTIONS
y
- LG’s steam technology allows you to inject fabrics with a swirling jet of hot
steam to refresh clothes, reduce static, and make ironing easier. Simply select
the STEAM FRESH™ cycle, or add a STEAM option to the selected cycles.
Operation
LED DisplayCycle Selector Knob
Power
Button
Start/Pause
Button
Dry Level
Button
Temp.
Control
Button
Time
Dry
Button
Signal
Button
INTRODUCING YOUR DRYER
MFL62512881_en_170329.indd 10 2017.3.29 2:22:45 PM
11
ENGLISH
Display
The display shows the settings, estimated time remaining, options, and status messages for your dryer. When the
dryer is turned on, the light in the display will illuminate.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
Button Description
ESTIMATED TIME REMAINING
y
- When the START/PAUSE button is pressed, the dryer will display the estimated
NOTE : The cycle time on SENSOR DRY cycles may fluctuate as the dryer
recalculates drying time for optimal results.
CYCLE COMPLETION INDICATOR WITH CHECK FILTER REMINDER
y
- This portion of the display shows which stage of the drying cycle is currently
CHILD LOCK INDICATOR
y
are disabled except the POWER button. This prevents children from changing
settings while the dryer is operating.
CHECK FILTER REMINDER
y
to check the filter. It turns off when the START/PAUSE button is pressed.
CUSTOM PROGRAM
y
- If you have a special combination of settings that you use frequently, you can
save these settings as a CUSTOM PROGRAM.
FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
y
- The FLOW SENSE™ duct blockage sensing system detects and alerts you
to blockages in the ductwork that reduce exhaust flow from the dryer. This
improves operating efficiency and helps minimize service calls, saving your
money.
INTRODUCING YOUR DRYER
MFL62512881_en_170329.indd 11 2017.3.29 2:22:52 PM
12
INSTALLATION INSTRUCTIONS
Preview Installation Order
Checking and choosing
the proper location
Leveling the dryer Venting the dryer
Plugging in the power cord
and grounding
Connecting Gas Dryers
(Gas Dryer Type)
Test runExhaust check test
(Refer to page 26.)
120V
240V(USA)
230V(CANADA)
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 12 2017.3.29 2:22:54 PM
13
ENGLISH
Installation Location Requirements
w
WARNING
Read all installation instructions completely before installing and operating your dryer! It is important that
you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical
connections, gas connections, and exhaust requirements are provided on the following pages.
at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in
an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not
permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building
inspector.
Clearances
Installation Spacing For Recessed Area Or Closet Installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of
reasons:
gas dryer must be exhausted to the outdoors.
See Venting the dryer.
Connecting
electric dryers.
appliance should also be considered.
No other fuel-burning appliance can be installed in the
same closet as a dryer.
installation and servicing.
and floor moldings.
of the dryer to reduce noise transfer.
For closet installation, with a door, minimum
ventilation openings in the top and bottom of the
door are required. Louvered doors with equivalent
ventilation openings are acceptable.
considered.
NOTE
operate correctly if dryer is not level.
NOTE
vibration from one to the other. Too much vibration, it could cause them to make noise or touch each other
causing paint damage and making even more noise.
24 in.
2*
(155 cm
2
)
18" min.*
(45.7 cm)
1"*
(2.5 cm)
32.1"
(81.4 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35.6 cm)
3"
*
(7.6 cm)
3"
*
(7.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
1"*
(2.5 cm)
5"**
(12.7 cm)
14" max.*
(35.6 cm)
18" min.*
(45.7 cm)
0"
(0 cm)
40.8"
(103.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
Requisitos
deventilación de
lapuerta del armario
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8" min.
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
18" min.*
(45,7 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
24 in.
2*
(155 cm
2
)
18" min.*
(45,7 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8"
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
1"**
(2.5 cm)
1"
(2.5 cm)
1"
(2.5 cm)
29"
(73.7 cm)
29"
(73.7 cm)
9"**
(22.9 cm)
7"* (17.8 cm)
7"* (17.8 cm)
1"* (2.5 cm)
5
"**
(14 cm)
2/4
81.6"
(207.2 cm)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
59"
(151.8 cm)
59"
(151.8 cm)
64"
(164.5 cm)
5"
(12.7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
2/4
2/4
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 13 2017.3.29 2:22:56 PM
14
INSTALLATION INSTRUCTIONS
Installation location requirements (Cont.)
w
WARNING
Read all installation instructions completely before installing and operating your dryer! It is important that
you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical
connections, gas connections, and exhaust requirements are provided on the following pages.
at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in
an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not
permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building
inspector.
Clearances (Space for Using the Dryer.)
A gas dryer must be exhausted to the outdoors. See
Venting Requirements(P.20).
Electrical
Requirements(P.24).
appliance should also be considered.
the same closet as a dryer.
24 in.
2*
(155 cm
2
)
18" min.*
(45.7 cm)
1"*
(2.5 cm)
32.1"
(81.4 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35.6 cm)
3"
*
(7.6 cm)
3"
*
(7.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
1"*
(2.5 cm)
5"**
(12.7 cm)
14" max.*
(35.6 cm)
18" min.*
(45.7 cm)
0"
(0 cm)
40.8"
(103.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
Requisitos
deventilación de
lapuerta del armario
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8" min.
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
18" min.*
(45,7 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
24 in.
2*
(155 cm
2
)
18" min.*
(45,7 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8"
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
1"**
(2.5 cm)
1"
(2.5 cm)
1"
(2.5 cm)
29"
(73.7 cm)
29"
(73.7 cm)
9"**
(22.9 cm)
7"* (17.8 cm)
7"* (17.8 cm)
1"* (2.5 cm)
5
"**
(14 cm)
2/4
81.6"
(207.2 cm)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
59"
(151.8 cm)
59"
(151.8 cm)
64"
(164.5 cm)
5"
(12.7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
2/4
2/4
If the duct is installed in the wall. If the duct isn’t installed in the wall.
MFL62512881_en_170329.indd 14 2017.3.29 2:22:56 PM
15
ENGLISH
Installation with optional pedestal base or stacking kit
RECOMMENDED INSTALLATION SPACING FOR CABINET INSTALLATION
For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.
*Required spacing
** For side or bottom venting,
CLOSET VENTILATION REQUIREMENTS
Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet. One
one foot above the floor. One example shown uses vent grilles in the door.
RECOMMENDED INSTALLATION SPACING FOR RECESSED OR CLOSET INSTALLATION, WITH STACKED WASHER
AND DRYER
*Required spacing
** For side or bottom venting,
24 in.
2*
(155 cm
2
)
18" min.*
(45.7 cm)
1"*
(2.5 cm)
32.1"
(81.4 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35.6 cm)
3"
*
(7.6 cm)
3"
*
(7.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
1"*
(2.5 cm)
5"**
(12.7 cm)
14" max.*
(35.6 cm)
18" min.*
(45.7 cm)
0"
(0 cm)
40.8"
(103.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
Requisitos
deventilación de
lapuerta del armario
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8" min.
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
18" min.*
(45,7 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
24 in.
2*
(155 cm
2
)
18" min.*
(45,7 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8"
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
1"**
(2.5 cm)
1"
(2.5 cm)
1"
(2.5 cm)
29"
(73.7 cm)
29"
(73.7 cm)
9"**
(22.9 cm)
7"* (17.8 cm)
7"* (17.8 cm)
1"* (2.5 cm)
5
"**
(14 cm)
2/4
81.6"
(207.2 cm)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
59"
(151.8 cm)
59"
(151.8 cm)
64"
(164.5 cm)
5"
(12.7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
2/4
2/4
24 in.
2*
(155 cm
2
)
18" min.*
(45.7 cm)
1"*
(2.5 cm)
32.1"
(81.4 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35.6 cm)
3"
*
(7.6 cm)
3"
*
(7.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
1"*
(2.5 cm)
5"**
(12.7 cm)
14" max.*
(35.6 cm)
18" min.*
(45.7 cm)
0"
(0 cm)
40.8"
(103.6 cm)
1"
(2.5 cm)
29"
(73.7 cm)
1"
(2.5 cm)
Requisitos
deventilación de
lapuerta del armario
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8" min.
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
18" min.*
(45,7 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
24 in.
2*
(155 cm
2
)
18" min.*
(45,7 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
48 in.
2*
(310 cm
2
)
14" max.*
(35,6 cm)
3"
*
(7,6 cm)
3"
*
(7,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"*
(2,5 cm)
5"**
(12,7 cm)
14" max.*
(35,6 cm)
18" min.*
(45,7 cm)
0"
(0 cm)
40.8"
(103,6 cm)
1"
(2,5 cm)
29"
(73,7 cm)
1"
(2,5 cm)
32.1"
(81.4 cm)
5"**
(12.7 cm)
1"**
(2.5 cm)
1"
(2.5 cm)
1"
(2.5 cm)
29"
(73.7 cm)
29"
(73.7 cm)
9"**
(22.9 cm)
7"* (17.8 cm)
7"* (17.8 cm)
1"* (2.5 cm)
5
"**
(14 cm)
2/4
81.6"
(207.2 cm)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
5"**
(12,7 cm)
1"**
(2,5 cm)
1"
(2,5 cm)
1"
(2,5 cm)
29"
(73,7 cm)
9"**
(22,9 cm)
7"* (17,8 cm)
7"* (17,8 cm)
1"* (2,5 cm)
5
"**
(14 cm)
81,6"
(207,2 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
29"
(73,7 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
32,1"
(81,4 cm)
32,1"
(81,4 cm)
59"
(151.8 cm)
59"
(151.8 cm)
64"
(164.5 cm)
5"
(12.7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
59"
(151,8 cm)
59"
(151,8 cm)
64"
(164,5 cm)
5"
(12,7 cm)
2/4
2/4
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 15 2017.3.29 2:22:58 PM
16
Leveling the dryer
w
WARNING
• To reduce the risk of injury to persons, adhere to all
industry recommended safety procedures including
the use of long sleeved gloves and safety glasses.
Failure to follow this warning can cause serious injury
or death.
• The appliances are heavy. Two or more people are
required when installing the dryer. Failure to follow
this warning can cause serious injury or death.
To ensure that the dryer provides optimal drying
performance, it must be level. To minimize vibration,
noise, and unwanted movement, the floor must be a
perfectly level, solid surface.
across the top of the dryer.
Gently push on the top corners of the dryer to make
sure that the dryer does not rock from corner to corner.
If you are installing the dryer on the optional pedestal,
you must use the leveling feet on the pedestal to
level the dryer. The dryer leveling feet should be fully
retracted.
Turn clockwise to raise the dryer or counterclockwise
to lower it. Raise or lower the leveling feet until dryer
is level from side to side and front to back.
the floor.
Level
Leveling Feet
NOTE
Adjust the leveling feet only as far as necessary to
level the dryer. Extending the leveling feet more than
necessary can cause the dryer to vibrate.
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 16 2017.3.29 2:22:59 PM
17
ENGLISH
To remove the door
w
WARNING
• To avoid damage to the dryer or the door, support
the door with a stool or box that fits under the
door, or have an assistant support the weight of
the door.
• Always reverse the door BEFORE stacking the
dryer on top of the washer.
• Avoid dropping the door to avoid damage to the
door or the floor.
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure
to follow the instructions below can result in damage
to the dryer, property damage or injury to persons.
Hinge
Dummy
Screw
Open Door
Remove
Door
Hinge Screw
Latch Screw
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 17 2017.3.29 2:23:5 PM
18
hole.
To install the door
w
WARNING
• To avoid damage to the dryer or the door, support
the door with a stool or box that fits under the
door, or have an assistant support the weight of
the door.
• Always reverse the door BEFORE stacking the
dryer on top of the washer.
• Avoid dropping the door to avoid damage to the
door or the floor.
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure
to follow the instructions below can result in damage
to the dryer, property damage or injury to persons.
Latch
Screw
Hinge Screw
Hinge
Dummy
Screw
Swing Door
Hinge hole
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 18 2017.3.29 2:23:11 PM
19
ENGLISH
Installing the Side Vent Kit
w
WARNING
• Use a heavy metal vent.
• Do not use plastic or thin foil duct.
• Clean old ducts before installing this dryer.
• To reduce the risk of injury to persons, adhere to all
industry recommended safety procedures including
the use of long sleeved gloves and safety glasses.
manual could result in property damage, injury to
persons, or death.
Your new dryer is shipped to vent to the rear.
It can also be configured to vent to the bottom or side
An adapter kit, part number 383EEL9001B, may be
purchased from your LG retailer. This kit contains the
necessary duct components to change the dryer vent
location.
out the exhaust duct.
Option 1: Side Venting
adapter duct onto the blower housing and secure to
the base of the dryer as shown.
faces AWAY from the dryer. Insert the elbow/duct
assembly through the side opening and press it onto
the adapter duct. Secure in place with duct tape.
Attach cover plate to the back of the dryer with
included screw.
Option 2: Bottom Venting
secure to the base of the dryer as shown.
that the male end of the elbow faces down through
hole in the bottom of the dryer. Secure in place with
duct tape.
Attach the cover plate to the back of the dryer with
included screw.
Rear
Exhaust Duct
Retaining
Screw
Elbow
Cover
Plate
Adapter
Duct
Adapter
Duct
Elbow
Cover
Plate
”
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 19 2017.3.29 2:23:13 PM
20
Venting the Dryer
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
Do not crush or collapse ductwork. Failure to follow
these instructions can result in fire or death.
Do not allow ductwork to rest on or contact sharp
objects. Failure to follow these instructions can result
in fire or death.
If connecting to existing ductwork, make sure it
is suitable and clean before installing the dryer.
Failure to follow these instructions can result in fire or
death.
Venting must conform to local building codes.
Failure to follow these instructions can result in fire or
death.
Gas dryers MUST exhaust to the outdoors.
Failure to follow these instructions can result in fire or
death.
Use only 4-inch (10.2 cm) rigid or flexible metal
ductwork inside the dryer cabinet and for venting
outside. Failure to follow these instructions can result
in fire or death.
To reduce the risk of fire, combustion, or
accumulation of combustible gases, DO NOT
exhaust dryer air into an enclosed and unventilated
area, such as an attic, wall, ceiling, crawl space,
chimney, gas vent, or concealed space of a
building. Failure to follow these instructions can result
in fire or death.
To reduce the risk of fire, DO NOT exhaust the dryer
with plastic or thin foil ducting.
Failure to follow these instructions can result in fire or
death.
The exhaust duct must be 4 inches (10.2 cm) in
diameter with no obstructions. The exhaust duct
should be kept as short as possible. Make sure
to clean any old ducts before installing your new
dryer. Failure to follow these instructions can result in
fire or death.
Rigid or semirigid metal ducting is recommended
for use between the dryer and the wall. In special
installations when it is impossible to make a
connection with the above recommendations, a
UL-listed flexible metal transition duct may be used
between the dryer and wall connection only. The
use of this ducting will affect drying time. Failure to
follow these instructions can result in fire or death.
DO NOT use sheet metal screws or other fasteners
which extend into the duct that could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. Failure to follow these
instructions can result in fire or death.
To maximize operating results, please observe
the duct length limitations noted in the chart next
page. Failure to follow these instructions can result in
fire or death.
Ductwork is not provided with the dryer. You
should obtain the necessary ductwork locally. The
end cap should have hinged dampers to prevent
backdraft when the dryer is not in use. Failure to
follow these instructions can result in fire or death.
The total length of flexible metal duct shall not
exceed 8 ft. (2.4 m)
In Canada, that only those foil-type flexible ducts,
if any, specifically identified for use with the
appliance by the manufacturer shall be used. In the
United States, that only those foil-type flexible ducts,
if any, specifically identified for use with the appliance
by the manufacturer and that comply with the Outline
be used.
INSTALLATION INSTRUCTIONS
MFL62512881_en_170329.indd 20 2017.3.29 2:23:13 PM
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
LG DLGX8001V Le manuel du propriétaire
- Catégorie
- Sèche-linge
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: LG DLGX8001V Owner's manual
Documents connexes
-
LG DLEX4070V Le manuel du propriétaire
-
LG DLEX7600VE Le manuel du propriétaire
-
LG DLEX3070V Le manuel du propriétaire
-
LG DLEX3650V Le manuel du propriétaire
-
LG DLEX3370V Manuel utilisateur
-
LG DLEX4270W Le manuel du propriétaire
-
LG 3828EL3010Y Manuel utilisateur
-
LG DLEY1201W Le manuel du propriétaire
-
LG DLEX2650T Le manuel du propriétaire