Kärcher 1.602-315.0 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
K 2 Car Care Kit
OPERATOR MANUAL
High-Pressure Washer . . . . . . . . . 2
MANUEL D’UTILISATION
Nettoyeur haute pression . . . . . 17
MANUAL DE USUARIO
Limpiador de alta presión . . . . . 34
59669850 (2015.12)
2 English
DANGER
indicates “an imminently hazardous situ-
ation which, if not avoided, will result in
death or serious injury.
WARNING
indicates “a potentially hazardous situa-
tion which, if not avoided, could result in
death or injury.’’
CAUTION
indicates “a potentially hazardous situa-
tion which, if not avoided, may result in
minor or moderate injury or in property
damage incidents.”
The owner and/or user must have an un-
derstanding of the manufacturer’s oper-
ating instructions and warnings before
using this pressure washer.
Warning information should be empha-
sized and understood.
If the operator is not fluent in English,
the manufacturer’s instructions and
warnings shall be read to and discussed
with the operator in the operator’s native
language by the purchaser/owner, mak-
ing sure that the operator comprehends
its contents.
Owner and/or user must study and
maintain for future reference the manu-
facturers’ instructions.
For household use only!
In the U.S. or Canada, please call
1-800-537-4129 for warranty issues and
visit www.karcher-help.com for techni-
cal support and product assistance.
Please take a moment to register your
pressure washer online at
www.karcher-register.com. Be sure to
save your purchase receipt, it will be re-
quired for repairs covered by warranty.
Call: 01-800-024-13-13 for help or visit
our website: www.karcher.com.mx
HIGH-PRESSURE WASHER OPERATOR MANUAL
Model Overview 3
Important Safety Instructions 4
Assembly Instructions 6
Operating Instructions 6
Using the Accessories 8
Working with Detergents 9
Taking a Break 10
Shutting Down and Clean-Up 10
Winterizing and Long-Term Storage 11
Maintenance Instructions 11
Cleaning Tips 12
Optional Cleaning Accessories 13
Troubleshooting 15
Safety Alert Symbols
Specifications
Max. Pressure 1600 PSI
Max. Water Flow 1.25 GPM
Amp draw 13 AMPS
Voltage 120 V
Part No. 1.602-315.0
Serial no.
Owner/User Responsibility
Customer Support
USA and Canada
Customer Support Mexico
English 3
1 Quick connect high-pressure outlet
2 High-pressure outlet
3 ON/OFF switch
4 Hose/Cord Hook
5 Handle
6 Collapsable transport handle
7 Spray Wand Storage
8 Trigger gun holder
9 Water inlet
10 Detergent suction hose with filter
11 Garden hose connector (female)
12 Water inlet connector
13 Power cord with Ground Fault Circuit
Interrupter (GFCI)
14 Wheels
15 Trigger gun
16 Trigger gun safety lock
17 Key to disconnect the high-pressure
hose from the trigger gun
18 High-pressure hose
19 Dirtblaster
®
(Rotary spray wand)
20 Vario Power Spray wand
21 Wash brush
22 Detergent foamer
Not included in the delivery
23 Water supply hose
MODEL OVERVIEW
4 English
WARNING
When using this product basic precau-
tions should always be followed, includ-
ing the following:
Read all the instructions before using
the product.
To reduce the risk of injury, close su-
pervision is necessary when a prod-
uct is used near children.
Know how to stop the product and
bleed pressures quickly. Be thor-
oughly familiar with the controls.
Stay alert – watch what you are do-
ing.
Do not operate the product when fa-
tigued or under the influence of alco-
hol or drugs.
Keep operating area clear of all per-
sons.
Do not overreach or stand on unsta-
ble support. Keep good footing and
balance at all times.
Follow the maintenance instructions
specified in the manual.
This product is provided with a
Ground Fault Circuit Interrupter built
into the power cord plug. If replace-
ment of the plug or cord is needed,
use only identical replacement parts.
WARNING
Risk of Injection or Injury – Do Not
Direct Discharge Stream At Persons.
High-pressure jets can be dangerous
if misused. The jet must not be di-
rected at persons, animals, electrical
devices, or the unit itself.
Wear safety goggles.
WARNING
Risk Of Explosion – Do not spray
flammable liquids.
Do not use acids, alkaline, solvents,
or any flammable material in this
product. These products can cause
physical injuries to the operator and
irreversible damage to the machine.
WARNING – Risk of Electrocu-
tion
Inspect cord before using – Do not
use if cord is damaged.
Keep all connections dry and off the
ground.
Do not touch plug with wet hands.
Do not use extension cord with this
product.
Connect to individual branch circuit
only.
CAUTION
This unit has been designed for use with
cleaning detergents recommended by the
manufacturer. The use of other cleaning
detergents may affect the operation of the
machine and void the warranty.
CAUTION
Gun kicks back – Hold with both
hands.
The Spray Gun Safety Lock prevents
the spray from accidentally being en-
gaged. This safety feature DOES
NOT lock spray in the ON position.
WARNING
DO NOT SPRAY ELECTRICAL APPA-
RATUS AND WIRING.
DO NOT USE WITH FLAMMABLE
LIQUIDS AND TOXIC CHEMICALS.
HIGH-PRESSURE. KEEP CLEAR OF
NOZZLE.
INJECTION HAZARD: EQUIPMENT
CAN CAUSE SERIOUS INJURY IF
THE SPRAY PENETRATES THE
SKIN. DO NOT POINT THE GUN AT
ANYONE OR ANY PART OF THE
BODY. IN CASE OF PENETRATION
SEEK MEDICAL AID IMMEDIATELY.
THIS SYSTEM IS CAPABLE OF PRO-
DUCING 1600 PSI TO AVOID RUP-
TURE AND INJURY, DO NOT
IMPORTANT SAFETY INSTRUCTIONS
English 5
OPERATE THIS PUMP WITH COM-
PONENTS RATED LESS THAN 1600
PSI WORKING PRESSURE (INCLUD-
ING BUT NOT LIMITED TO SPRAY
GUNS, HOSE AND HOSE CONNEC-
TIONS).
BEFORE SERVICING, CLEANING
OR REMOVING ANY PARTS, SHUT
OFF POWER AND RELIEVE PRES-
SURE.
IF CONNECTION IS MADE TO A PO-
TABLE WATER SYSTEM, THE SYS-
TEM SHALL BE PROTECTED
AGAINST BACK FLOW.
In a double-insulated product, two sys-
tems of insulation are provided instead
of grounding. No grounding means is
provided on a double-insulated product,
nor should a means for grounding be
added to the product. Servicing a dou-
ble-insulated product requires extreme
care and knowledge of the system, and
should be done only by qualified service
personnel. Replacement parts for a dou-
ble-insulated product must be identical
to the parts they replace. A doubleinsu-
lated product is marked with the words
“DOUBLE INSULATION” or “DOUBLE
INSULATED”. The symbol may also
be marked on the product.
This pressure washer is provided with a
ground-fault circuit-interrupter (GFCI)
built into the plug of the power-supply
cord. This device provides additional
protection from the risk of electric shock.
Should replacement of the plug or cord
become necessary, use only identical
replacement parts that include GFCI
protection.
CAUTION
When connecting the water inlet to the
water supply mains, local regulations of
your water company must be observed.
In some areas the unit must not be con-
nected directly to the public drinking wa-
ter supply. This is to ensure that there is
no feedback of chemicals into the water
supply. Direct connection via a receiver
tank or backflow preventer, for example,
is permitted.
Dirt in the feed water will damage the
unit. To avoid this risk, we recommend
fitting a water filter.
Garden hose must be at least 13 mm
or 16 mm (1/2 inch or 5/8) inch in di-
ameter.
Flow rate of water supply must not
fall below 7.6 L/min. (2 GPM/gallons
per minute).
Flow rate can be determined by run-
ning the water for one minute into an
empty 20 litre (5-gallon) container.
The water supply temperature must
not exceed 40°C/104°F.
Never use the pressure washer to
draw in water contaminated with sol-
vents, e.g. paint thinners, gasoline,
oil, etc.
Always prevent debris from being
drawn into the unit by using a clean
water source.
SAVE THESE INSTRUCTIONS!
SERVICING OF A DOUBLE-
INSULATED PRODUCT
GROUND FAULT CIRCUIT
INTERRUPTER PROTECTION
WATER SUPPLY
(Cold Water Only)
6 English
STEP 1:
Insert wheels into the body of the
unit.
STEP 2:
Slide the transport handle into place.
STEP 3:
Install the water inlet connector to the
unit’s water inlet.
Note: Never attach the garden hose
connector to the unit’s water inlet!
STEP 4:
Fasten the quick connect to the high-
pressure outlet.
STEP 5:
Pull out the locking slide of the trigger
gun handle.
Insert the small end of the high-pres-
sure hose into place.
Push the locking slide back into the
trigger gun to lock the hose in posi-
tion.
STEP 1:
Insert one end of the high-pressure
hose tightly into the quick connect on
the unit, it will lock in audibly.
Note: Make sure the connection nip-
ple is aligned correctly. Check the
connection by pulling on the high-
pressure hose.
Check the secure connection by pull-
ing on the high-pressure hose.
ASSEMBLY INSTRUCTIONS
Assembly
OPERATING
INSTRUCTIONS
English 7
STEP 2:
Insert the spray wand of your choice
into the trigger gun. Press in against
the spring tension and twist into
locked position.
STEP 3:
1 Screw the supplied garden hose con-
nector on to the end of your garden
hose.
2 Push the garden hose connector on
to the water inlet connector and
make sure you hear it click into place
before proceeding.
STEP 4:
Connect garden hose to the cold wa-
ter source and turn water on com-
pletely.
STEP 5:
Plug the Ground Fault Circuit Inter-
rupter (GFCI) into a working outlet.
We recommend that you test the GFCI as
part of your startup procedure each time
you use your pressure washer. To learn
how to peform this test on your unit, visit
http://www.karcherresidential.com/
gfci_test.php for detailed instructions for
your type of GFCI.
WARNING
Do not use if above test fails.
Note: The actual appearance of the GFCI
may be different from this illustration.
STEP 6:
Unlock the trigger gun safety lock.
Trigger the gun to eliminate trapped
air, wait for a steady flow of water to
emerge from the spray nozzle.
STEP 7:
Turn on the high-pressure washer (I/
ON).
The motor starts only if the trigger
of the gun is pulled and shuts off
when the trigger is released.
8 English
WARNING
To avoid serious injury never point spray
nozzle at yourself, other persons or ani-
mals.
CAUTION
Always test an inconspicuous area be-
fore cleaning with high-pressure.
This nozzle features a pencil jet which ro-
tates 360º for maximum dirt cutting action,
effectively increasing cleaning performance
up to 50%. This nozzle combines the clean-
ing performance of a 0º pencil jet with the
surface coverage of a wide angle nozzle.
Not recommended for soft materials,
siding, painted surfaces, decks or
autos.
The Vario Power Spray Wand allows
you to adjust the cleaning pressure.
To clean at maximum pressure, the
wand must be positioned to the high-
pressure setting (Max).
For reduced pressure turn the wand
collar in the "Min" direction.
To apply detergent, the wand must
be positioned to the low-pressure
setting (Mix).
Ideal for applications which require a
thick foam. Simply fill the resevoir cup
with liquid pressure washer detergent to
generate a foam spray. Connects direct-
ly to the trigger gun.
This brush is ideal for removing stub-
born dirt and stains from finished surfac-
es. Use with detergents possible.
USING THE ACCESSORIES
Dirtblaster
®
Vario Power Spray Wand
Detergent Foamer
Wash Brush
English 9
For best results see Cleaning Tips for
specific information on how to clean
different surfaces.
Always Use Kärcher
®
Detergent for
Best Results
Kärcher
®
biodegradable detergents are
specially formulated to protect the envi-
ronment and your pressure washer. The
special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a longer
life. For Kärcher
®
detergents, check
your retailer or visit our website:
www.buykarcher.com
CAUTION
Never use:
Bleach, chlorine products and other
corrosive chemicals
Liquids containing solvents (i.e.,
paint thinners, gasoline, oils)
Tri-sodium phosphate products
Ammonia products
Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
Use of these items will void the war-
ranty.
STEP 1:
Detergents can only be applied at
low pressure.
Install the Vario Power Spray Wand.
Set the spray wand to the low pres-
sure setting (Mix).
OR
Install the Wash Brush.
STEP 2:
Fill a container with Kärcher deter-
gent. Place the filter end of detergent
siphon tube into the container.
STEP 3:
Turn on the pressure washer (I). Pull
trigger to operate unit. Liquid deter-
gent is drawn into the unit and mixed
with water. Apply detergent to work
area. Do not allow detergent to dry
on surface.
STEP 4:
To rinse, insert the spray wand and
pull trigger to operate unit.
STEP 5:
Cleaning up: Always draw fresh wa-
ter through the detergent tank or si-
phon tube when done to flush any
remaining detergents from the injec-
tion system.
WORKING WITH
DETERGENTS
10 English
STEP 1:
Release trigger and engage gun
safety lock.
STEP 2:
Turn pressure washer to OFF (0) po-
sition.
STEP 1:
Turn the switch to OFF (0) position
and unplug cord from outlet.
STEP 2:
Turn off the water source.
STEP 3:
Press trigger to release water pres-
sure.
STEP 4:
Release trigger and engage gun
safety lock.
STEP 5:
Disconnect the garden hose from the
water inlet on the unit.
CAUTION
When disconnecting the supply or high-
pressure hose, warm water may leak
from the connector after operation.
STEP 6:
Push the housing of the quick con-
nect toward the rear and disconnect
the high-pressure hose from the unit.
TAKING A BREAK ... five
minutes or more
SHUTTING DOWN &
CLEAN-UP
English 11
1 Disconnect all water connections.
2 Turn on the machine for a few sec-
onds, until the water which had re-
mained in the pump exits, turn off
immediately.
3 Do not allow high-pressure hose to
become kinked.
4 Store the machine and accessories
in a room which does not reach
freezing temperatures. DO NOT
store near furnace or other sources
of heat as it may dry out the pump
seals.
CAUTION
Failure to follow the above directions will
result in damage to the pump assembly
and accessories and will void the war-
ranty.
Kärcher
®
also recommends the regular
practice of using a pump protector like
“Kärcher
®
Pump Guard” to prevent cold
weather damage during storage in the
winter months.
STEP 1:
Disconect the connector from the
water inlet.
STEP 2:
Pull out water inlet filter with flat-nose
pliers.
STEP 3:
Rinse out water inlet filter in warm
water.
STEP 4:
Reinsert water inlet filter into the wa-
ter inlet.
The unit is maintenance-free.
WINTERIZING AND LONG-
TERM STORAGE
CARE AND MAINTENANCE
INSTRUCTIONS
Cleaning the water inlet filter
Maintenance
12 English
CAUTION
Before cleaning any surface an in-
conspicuous area should be cleaned
to test spray pattern and distance for
maximum cleaning results.
If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the
loose paint from the surface.
When using on surfaces which might
come in contact with food, flush sur-
faces with plenty of drinking water.
For additional cleaning tips and a
complete video library, visit our web-
site:
www.karcherresidential.com
(with or without detergent). Pre-rinse
deck and surrounding area with fresh
water. If using detergent, apply to sur-
face at low pressure. For best results,
limit your work area to smaller sections
of approximately 2.3 m² (25 sq. ft.). Al-
low detergent to remain on surface 1-3
minutes. Do not allow detergent to dry
on surface. Rinse at high-pressure in a
long sweeping motion keeping the spray
nozzle approximately 7.5-15 cm (3-6 in.)
from the cleaning surface. Always clean
from top to bottom and from left to right.
When moving on to a new section of the
cleaning surface, be sure to overlap the
previous section to eliminate stop marks
and ensure a more even cleaning result.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent, apply to surface at low
pressure (for best results, limit your
work area to sections of approximately
1.8 m (6 ft.) and always apply detergent
from bottom to top). Allow detergent to
remain on surface 1-3 minutes. Do not
allow detergent to dry on surface, if sur-
face appears to be drying, simply wet
down surface with fresh water. If need-
ed, use special wash brush attachment
(not included) to remove stubborn dirt.
Rinse at high-pressure from top to bot-
tom in an even sweeping motion keep-
ing the spray nozzle approximately
1.8 m (6 ft.) from the cleaning surface.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent or Degreaser, apply to
surface at low pressure. For best re-
sults, limit your work area to smaller sec-
tions of approximately 2.3 m² (25 sq. ft.).
Allow detergent or Degreaser to remain
on surface 1-3 minutes. Do not allow de-
tergent to dry on surface. Rinse at high-
pressure in a sweeping motion keeping
the spray nozzle approximately 7.5-
15 cm (3-6 in.) from the cleaning sur-
face. Always clean from top to bottom
and from left to right. For removing ex-
tremely stubborn stains, use the
Dirtblaster
®
Nozzle.
(with or without detergent). Pre-rinse
vehicle with fresh water. If using deter-
gent, apply to surface at low pressure.
For best results, clean one side of vehi-
cle at a time and always apply detergent
from bottom to top, do not allow deter-
CLEANING TIPS
Deck Cleaning
House Siding
Cement Patios, Brick and Stone
Cars, Boats and Motorcycles
English 13
gent to dry on surface. If needed, use
special wash brush attachment (not in-
cluded) to remove stubborn dirt. Rinse
at high-pressure in a sweeping motion
keeping the spray nozzle approximately
15-20 cm (6-8 in.) from the cleaning sur-
face (distance should increase when
rinsing pin-striping or other sensitive
surfaces). Always clean from top to bot-
tom and from left to right. For best re-
sults, wipe surface dry with a chamois or
soft dry cloth.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent or Degreaser, apply deter-
gent at low pressure. Allow detergent to
remain on surface 1-3 minutes. Do not
allow detergent to dry on surface. Rinse
at high-pressure keeping the spray noz-
zle approximately 7.5-15 cm (3-6 in.)
from the cleaning surface. For removing
extremely stubborn dirt, it may be nec-
essary to move the spray nozzle even
closer to the surface for greater dirt cut-
ting action.
(with or without detergent). Pre-rinse
furniture and surrounding area with
fresh water. If using detergent, apply to
surface at low pressure. Allow detergent
to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface. If
needed use special Wash Brush Attach-
ment (not included) to remove stubborn
dirt. Rinse at high-pressure in a sweep-
ing motion keeping the spray nozzle ap-
proximately 7.5-15 cm (3-6 in.) from the
cleaning surface. For best results, clean
from top to bottom and from left to right.
Optional accessories are available to
further enhance your cleaning capabili-
ties. These accessories are accurate as
of the printing date of this manual.
Please check our website for pricing and
up-to-date information.
Specially formulated to protect your
pressure washer from freezing, corro-
sion and premature wear. The Pump
Guard also adds lubrication to valves
and seals to prevent sticking. Highly rec-
ommended for all Kärcher
®
pressure
washers!
Part No. 9.558-998.0
Extension Hose for all Kärcher
®
high-
pressure washers between the original
equipment hose and gun up to
2000 PSI.
Part No. 2.642-588.0
Need to clean second story windows or
other high areas? Increase the reach of
your pressure washer by up to 1.67 m
(66 in.) with this extension kit. Includes 4
aluminum sections for variable length.
1.67 m (66 in.) fully assembled. Fits
most Kärcher
®
pressure washers up to
2300 PSI. (bayonet)
Part No. 2.640-746.0
Barbecue Grills, Outdoor Power
Equipment and Gardening Tools
Patio and Lawn Furniture
OPTIONAL CLEANING
ACCESSORIES
Pump Guard
7.5 m (25 ft.) Extension High-
Pressure Hose
1.67 m (66 in.) Extension Wand
(four-piece)
14 English
For more effortless cleaning of all
smooth surfaces (painted, glass and
plastic) try the Kärcher
®
Rotating Wash
Brush. Use it on your automobile, house
siding or windows. The water pressure
from your pressure washer causes the
inner brushes to gently spin, making
your cleaning job much easier. The an-
gle of brush head is adjustable to help
you reach difficult areas. Excellent for
the application of detergent. A must-
have accessory designed for Kärcher
®
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 2.640-743.0
Made with soft bristles that will not harm
painted surfaces. Easily attaches direct-
ly to the trigger gun. Ideal for stubborn
dirt on cars, boats, patio furniture and
other surfaces. Great for applying deter-
gent. Fits most Kärcher
®
pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.640-740.0
Need to clean blocked pipes, drains or
downspouts? The Kärcher
®
pipe clean-
ing kit is the answer! The pipe cleaner
propels itself forward while simultane-
ously flushing out debris. For example,
insert the cleaning nozzle in the base of
a downspout, pull the trigger on the
pressure washer gun and watch as the
nozzle shoots out leaves and other de-
bris while climbing upward. Connects di-
rectly to the trigger gun of most
Kärcher
®
pressure washers up to
2300 PSI. (bayonet)
Part No. 2.640-747.0
Why spend hours stripping old paint and
rust by hand using harsh chemicals? Let
the Kärcher
®
Wet Sandblasting Kit do
the work! Attach the kit to your pressure
washer, add abrasive material and at-
tack the rust and paint with our eco-
friendly alternative. Fits most Kärcher
®
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 2.638-792.0
Ideal for applications which require a
thick foam. Simply fill the resevoir cup
with liquid pressure washer detergent to
generate a foam spray. Connects direct-
ly to the trigger gun. Fits most Kärcher
®
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 6.964-507.0
For cleaning surfaces such as patios,
terraces and driveways without splash-
back, there is no better solution than the
Kärcher
®
T 200. It saves time by clean-
ing a 30 cm (1 ft.) wide area gently as it
hovers, providing consistent, streak-free
cleaning. When you finish cleaning the
patio and driveway, remove the wand
and use the handle to clean garage
doors and other vertical surfaces. In-
cludes two nozzles which spin at high
speed for optimum results. Our top sell-
ing accessory for Kärcher
®
pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.642-188.0
Rotating Wash Brush (bayonet)
Soft Clean Washing Brush
7.5 m (25 ft.) Pipe Cleaning Kit
(bayonet)
Wet Sandblasting Kit (bayonet)
Detergent Foamer Attachment
T 200 Wide Area Surface Cleaner
English 15
WARNING
Disconnect the unit from the power source before making any repair.
TROUBLESHOOTING
Issue Cause Solution
Motor will not start On/Off switch is in the “OFF”
(0) position.
Turn switch to the “ON” (I)
position
Power cord is not plugged in. Plug in power cord.
Electrical outlet does not
supply adequate power.
Try a different outlet.
Tripped GFCI plug. Press “RESET” button on
GFCI plug.
Tripped circuit breaker. Switch off pressure washer.
The reset comes automatically
once the temperature of the
unit drops.
Unit does not
reach high-pres-
sure.
Diameter of garden hose is too
small.
Replace with a 16 mm (5/8
inch) or larger garden hose.
Water supply is restricted. Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Spray wand is on low-pressure
position.
Turn spray wand to high-pres-
sure position.
Output pressure
varies high and
low.
Not enough inlet water supply. Turn water on full force. Check
garden hose for kinks, leaks or
blockage.
Pump is sucking air. Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow
of water emerges through the
nozzle.
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Discharge nozzle is
obstructed.
Blow out or remove debris with
a fine needle.
Calcified gun, hose or spray
wand.
Run distilled vinegar through
detergent suction tube.
16 English
No detergent. Detergent is too thick. Dilute detergent, for best
results use Kärcher detergent.
Filter on detergent siphon tube
is clogged.
Run warm water through filter
to remove debris.
Damaged or clogged detergent
siphon tube.
Remove obstruction or replace
detergent siphon tube.
Spray wand is in high-pressure
position.
Turn spray wand tip to low-
pressure position.
Discharge nozzle is
obstructed.
Blow out or remove debris with
fine needle.
Garden hose
connection leaks.
Loose fittings. Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Spray wand leaks. Spray wand not properly
attached.
Insert the spray wand into the
trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Broken o-ring or plastic insert. Call Customer Support
Pump is noisy. Pump is sucking air. Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow
of water emerges through the
nozzle.
Water leaks from
pump (up to 10
drops per minute
is permissible).
Loose fittings. Check that all fittings are tight.
Water seals are damaged or
worn.
Call Customer Support
Oil drip. Oil seals are damaged or worn. Call Customer Support
Issue Cause Solution
If you encounter any additional difficulties not listed, please visit our website.
USA / Canada:
www.karcher-help.com
Mexico:
www.karcher.com.mx
Français 17
DANGER
Identifie « une situation de danger im-
minent qui, si elle n'est pas évitée, en-
traîne la mort ou des blessures
graves ».
AVERTISSEMENT
Identifie « une situation de danger po-
tentiel qui, si elle n'est pas évitée, pour-
rait entraîner la mort ou des blessures ».
ATTENTION
Identifie « une situation de danger po-
tentiel qui, si elle n'est pas évitée, peut
éventuellement entraîner des blessures
légères ou modérées » ou des dom-
mages matériels.
Avant d'utiliser ce nettoyeur pression, le
propriétaire et/ou l'utilisateur doit impé-
rativement avoir pris connaissance des
consignes d'utilisation et mises en garde
du fabricant.
Il est nécessaire d'insister sur les aver-
tissements et de les comprendre.
Si l'utilisateur ne parle pas couramment
l'anglais, l'acheteur/le propriétaire doit
lire les consignes et mises en garde du
fabricant avec l'utilisateur dans la
langue maternelle de ce dernier et s'as-
surer qu'il en comprend bien le contenu.
Le propriétaire et/ou l'utilisateur doit se
familiariser avec les consignes du fabri-
cant et les conserver afin de pouvoir s'y
référer ultérieurement.
À usage domestique seulement!
Pour faire valoir une demande en garan-
tie, appelez le : 1-800-537-4129. Toutes
les autres informations sont disponibles
sous : www.karcher-help.com
Prenez le temps d'enregistrer votre net-
toyeur haute pression en ligne en vous
adressant à www.karcher-regis-
ter.com. Veuillez à conserver précieu-
sement votre preuve d'achat, qui sera
exigée en cas de réparation assujettie à
la garantie.
Appeler : 01-800-024-13-13 pour obte-
nir de l'aide ou visitez notre site Web :
www.karcher.com.mx
NETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATION
Généralités 18
Consignes de sécurité importantes 19
Instructions de montage 21
Mode d'emploi 22
Utilisation des accessoires 23
Emploi de détergents 24
Prendre une pause 25
Arrêt de l'appareil et nettoyage 25
Entreposage à long terme 26
Consignes d'entretien 27
Conseils de nettoyage 27
Accessoires de nettoyage en option 29
Dépannage 31
Symboles d'alerte de sécurité
Caractéristiques
Pression max. 1600 PSI
Débit d'eau max. 1.25 GPM
Ampérage 13 AMPS
Tension 120 V
N° de pièce 1.602-315.0
N° de série
Responsabilité du propriétaire
de l'utilisateur
Service client É.-U.A et Canada
Assistance Mexique
18 Français
1 Prise haute pression à connexion
rapide
2 Sortie haute pression
3 Interrupteur marche/arrêt
4 Support de rangement pou tuyau/
cordon
5 Poignée
6 Poignée de transport, réglable en
hauteur
7 Rangement, lance
8 Compartiment de la poignée-pistolet
9 Arrivée d'eau
10 Flexible d'aspiration du détergent
avec filtre
11 Raccord pour tuyau d'arrosage
(femelle)
12 Raccord pour arrivée d'eau
13 Cordon d'alimentation avec
disjoncteur différentiel
14 Roulette de transport
15 Poignée-pistolet
16 Verrouillage de sécurité de la
poignée-pistolet
17 Touche pour séparer le tuyau à
haute pression de la poignée-pistolet
18 Tuyau à haute pression
19 Dirtblaster
®
(lance rotative)
20 Lance Vario
21 Brosse de lavage
22 Embout moussant
Pas comprise dans l'étendue de livraison
23 Tuyau d'alimentation d'eau
GÉNÉRALITÉS
Français 19
AVERTISSEMENT
En utilisant ce produit, toujours observer
une certaine prudence élémentaire, in-
cluant notamment :
Lire toutes les instructions de service
avant d'utiliser l'appareil.
Afin de minimiser les risques de bles-
sure, ne jamais laisser l'appareil
sans surveillance lorsque celui-ci est
utilisé à proximité d'enfants.
Il est impératif de savoir arrêter et
mettre l'appareil hors pression rapi-
dement. Une connaissance appro-
fondie des commandes est
nécessaire.
Rester attentif – se concentrer sur la
tâche en cours.
L'utilisateur ne doit jamais faire
usage de l'appareil lorsqu'il est fati-
gué ou sous l'emprise d'alcool ou de
drogues.
Veiller à ce qu'aucun individu ne se
trouve dans la zone de travail.
Ne jamais passer ou monter sur des
supports instables. Toujours rester
stable et équilibré.
Respecter les consignes d'entretien
figurant dans le manuel.
Ce produit est fourni avec un disjonc-
teur différentiel monté dans la fiche
du cordon d'alimentation. Si le rem-
placement de la fiche ou du cordon
d'alimentation s'avère nécessaire,
n'utiliser que des pièces de rechange
identiques.
AVERTISSEMENT
Risque de projection ou de blessure
– Ne pas diriger le jet de vapeur en
direction d'individus.
En cas d'utilisation incorrecte, les
jets haute pression peuvent être dan-
gereux. Ne jamais diriger les jets de
vapeur en direction d'individus, d'ani-
maux, de dispositifs électriques ou
de l'appareil lui-même.
Le port de lunettes de protection est
obligatoire.
AVERTISSEMENT
Risque d'explosion – Ne pas vapori-
ser de liquides inflammables.
N'utiliser en aucun cas d'acides, de
solutions alcalines, de solvants ou de
produits inflammables dans cet ap-
pareil. Ces produits peuvent être à
l'origine de blessures graves ou d'en-
dommagement irréversible de l'ap-
pareil.
AVERTISSEMENT
– Risque d'électrocution
Examiner le cordon avant de l'utiliser
– Ne pas utiliser de cordon endom-
magée.
Garder toutes les connexions au sec
et ne pas les laisser à terre.
Ne pas toucher la fiche avec les
mains mouillées.
Ne pas utiliser de rallonges.
Brancher à une dérivation distincte.
ATTENTION
Cette machine a été conçue pour être
utilisée avec des détergents du fabri-
cant. L'utilisation d'autres détergents
peut altérer le fonctionnement de la ma-
chine et annuler la garantie.
ATTENTION
Le pistolet génère une force de pro-
pulsion – Le maintenir toujours à
deux mains.
Le dispositif de sécurité de la poi-
gnée-pistolet permet d'éviter tout ac-
tionnement accidentel de la
gâchette. Ce dispositif de sécurité
NE verrouille PAS la gâchette en po-
sition marche (ON).
CONSIGNES DE SÉCURITÉ IMPORTANTES
20 Français
ATTENTION
NE PAS ASPERGER DES APPA-
REILS OU CÂBLAGES ÉLEC-
TRIQUES.
NE PAS UTILISER AVEC DES LI-
QUIDES INFLAMMABLES OU DES
PRODUITS CHIMIQUES TOXIQUES.
HAUTE PRESSION. NE PAS S’AP-
PROCHER DE LA BUSE.
RISQUE D'INJECTION : L'ÉQUIPE-
MENT PEUT CAUSER BLESSURES
GRAVES SI LE JET PÉNÈTRE SOUS
LA PEAU. NE PAS DIRIGER LE PIS-
TOLET SUR UNE PERSONNE OU
UNE QUELCONQUE PARTIE DU
CORPS. EN CAS DE PÉNÉTRATION,
DEMANDER IMMÉDIATEMENT DES
SOINS MÉDICAUX.
CE SYSTÈME EST CAPABLE DE
PRODUIRE UNE PRESSION DE 1600
PSI. AFIN D'ÉVITER TOUT RISQUE
DE RUPTURE OU DE BLESSURE,
NE PAS UTILISER CETTE POMPE
AVEC DES ÉLÉMENTS DANS LA
PRESSION DE SERVICE NOMINALE
EST INFÉRIEURE À 1600 PSI (Y
COMPRIS LES PULVÉRISATEURS,
TUYAUX ET RACCORDS).
COUPER LE COURANT ET RELA-
CHER LA PRESSION AVANT DE
PROCÉDER AU DÉPANNAGE, AU
NETTOYAGE OU À TOUT ENLÈVE-
MENT DE PIÈCE
SI CET APPAREIL EST RACCORDÉ
À UN RÉSEAU D’EAU POTABLE, CE
DERNIER DOIT ÊTRE PROTÉGÉ
CONTRE LES RETOURS.
Dans un appareil à double isolation,
deux isolations distinctes remplacent la
mise à la terre. L’appareil à double iso-
lation n’est pourvu d’aucun dispositif de
mise à la terre et un tel dispositif ne doit
pas être ajouté. L’entretien d’un appareil
à double isolation demande beaucoup
de soins ainsi qu’une bonne connais-
sance du système et ne davrait être ef-
fectué que par un techncien d’entretien
qualifé. Les pièces de rechange d’un
appareil à double isolation doivent être
identiques aux pièces originales.
Ce produit est fourni avec un disjoncteur
différentiel intégré dans la fiche de cor-
don d'alimentation. Ce dispositif fournit
une protection supplémentaire contre
les risques de décharges électriques.
Utiliser des pièces de rechange iden-
tiques en cas de remplacement du cor-
don ou de la fiche.
ATTENTION
Lors de la connexion de l'entrée d'eau à
la canalisation d'alimentation en eau, les
régulations locales de votre compagnie
des eaux doivent être observées. Dans
certaines zones, l'appareil ne doit pas
être connecté directement à l'alimenta-
tion en eau potable publique. Il s'agit de
s'assurer qu'il n'y a pas de retour de pro-
duits chimiques dans l'alimentation en
eau. Une connexion directe par l'inter-
médiaire d'un réservoir de réception ou
d'un disconnecteur hydraulique par
exemple est autorisée.
ENTRETIEN DES APPAREILS A
DOUBLE ISOLATION
Protection par disjoncteur
différentiel
ALIMENTATION EN EAU (eau
froide seulement)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Kärcher 1.602-315.0 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur