KitchenAid KSSC42FTS18 Guide d'installation

Ki|chen_kid _

SIDE BY SIDE BUILT-IN REFRIGERATOR

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. kA INSTALACION REQUIERE DE 20 MAS PERSONAS.

P P P J_. % J_.

REFRIGERATEUR ENCASTRE COTE A COTE

{_,,_, _,_ ......

IMPORTANT : LIRE IT CONSERVER CES INSTRUCTIONS. L'INSTALLATION NiCESSlTE L'INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/[ndice/Table des matieres .................................................................. 2

W10555563A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

MODELS .......................................................................................... 4

INSTALLATION REQUIREMENTS ................................................ 6

Tools and Parts ............................................................................ 6

Location Requirements ................................................................ 6

Electrical Requirements ............................................................... 7

Water Supply Requirements ........................................................ 8

Tipping Radius ............................................................................. 8

Product Dimensions ..................................................................... 9

Door Swing Dimensions ............................................................. 10

Overlay Series Door Panel and Cabinetry Clearance ................ 11

Overlay Series Custom Panels and Handle Kits ....................... 13

Classic Series Factory Panels and Kits ..................................... 15

Classic Series Custom Panels ................................................... 16

Classic, Architect ®and Complete Series

Custom Side Panels ................................................................... 18

Overlay Series Custom Side Panels .......................................... 18

INSTALLATION INSTRUCTIONS ................................................ 19

Unpack the Refrigerator............................................................. 19

Reduce Tipping Radius.............................................................. 20

Move the Refrigerator into House .............................................. 20

Install Anti-Tip Boards ................................................................ 20

Connect the Water Supply ......................................................... 21

Plug in Refrigerator ..................................................................... 22

Move Refrigerator to Final Location........................................... 22

Level and Align Refrigerator ....................................................... 23

Install Classic Series Custom Panels ......................................... 23

Install Overlay Series Custom Panels ........................................ 24

Adjust Doors ............................................................................... 25

Install Side Panel ........................................................................ 26

Install Base Grille ........................................................................ 26

Complete Installation.................................................................. 27

Water System Preparation ......................................................... 27

p

INDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 28

MODELOS ..................................................................................... 29

REQUlSITOS DE INSTALACION ................................................. 31

Piezas y herramientas ................................................................ 31

Requisitos de ubicaci6n ............................................................. 31

Requisitos electricos .................................................................. 32

Requisitos del suministro de agua ............................................. 33

Arco de vuelco ........................................................................... 33

Medidas del producto ................................................................ 34

Medidas de oscilaci6n de las puertas ....................................... 35

Espacio para el panel de la puerta y para los armarios

de la serie de paneles recubiertos ............................................. 36

Paneles a la medida y juegos de manijas

de la serie de paneles recubiertos ............................................. 38

Paneles y juegos de fabrica de la serie Classic ........................ 40

Paneles a la medida para de la serie Classic ............................ 41

Paneles laterales a la medida para las

series Classic, Architect ®y Complete ........................................ 43

Paneles laterales a la medida para la

serie de paneles recubiertos ...................................................... 44

INSTRUCCIONES DE INSTALACION ......................................... 45

Desempaque el refrigerador ...................................................... 45

C6mo reducir el arco de vuelco ................................................. 45

C6mo hacer entrar el refrigerador en la casa ............................ 45

C6mo instalar los tableros antivuelco ........................................ 46

Conexi6n del suministro de agua .............................................. 46

C6mo enchufar el refrigerador ................................................... 48

C6mo mover el refrigerador a su ubicaci6n final ....................... 48

Nivelaci6n y alineamiento del refrigerador ................................. 48

C6mo instalar los paneles a la medida

para la serie Classic ................................................................... 49

Como instalar los paneles a la medida para

la serie de paneles recubiertos .................................................. 50

Ajuste las puertas ....................................................................... 51

Como instalar el panel lateral ..................................................... 52

Como instalar la rejilla de la base .............................................. 52

Como terminar la instalacion ..................................................... 53

Preparacion del sistema de agua .............................................. 53

TABLEDES MATIERES

SECURITE DU REFRIGERATEUR .............................................. 54

MODELES ..................................................................................... 55

EXIGENCES D'INSTALLATION ................................................... 57

Outillage et pieces ...................................................................... 57

Exigences d'emplacement ......................................................... 57

Specifications electriques .......................................................... 58

Specifications de I'alimentation en eau ..................................... 59

Rayon de basculement .............................................................. 59

Dimensions du produit ............................................................... 60

Dimensions pour I'ouverture des portes .................................... 61

Serie Panneaux decoratifs - Panneau de porte

et placard - espace libre ............................................................ 62

Panneaux personnalises et poignees de la serie

Panneaux decoratifs .................................................................. 64

Ensembles de panneaux d'origine de la serie Classic .............. 66

Panneaux personnalises de la serie Classic .............................. 67

Panneaux lateraux personnalises

des series Classic, Architect ®et Complete ................................ 69

Panneaux lateraux personnalises de la serie Overlay ............... 70

INSTRUCTIONS D'INSTALLATION ............................................. 70

Deballage du r6frigerateur .......................................................... 70

Reduction du rayon de basculement ......................................... 71

Faire entrer le refrig6rateur dans le domicile ............................. 71

Installation de planches antibasculement .................................. 72

Raccordement &I'alimentation en eau ...................................... 72

Branchement du r6frigerateur .................................................... 74

Deplacement du refrig6rateur & I'emplacement final................. 74

Reglage de I'aplomb et alignement du refrig6rateur ................. 74

Installation des panneaux personnalises

de la serie Classic ....................................................................... 75

Installation des panneaux personnalises

de la serie Panneaux decoratifs ................................................. 76

Ajustement des portes ............................................................... 77

Installation du panneau lateral ................................................... 78

Installation de la grille de la base ............................................... 78

Achever I'installation .................................................................. 79

Preparation du systeme d'eau ................................................... 79

2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

MODELS

Side by Side Non-Dispensing Refrigerators

Architect _ Series

Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking

built-in refrigerator.

KSSC36FTS KSSC42FTS KSSC48FTS

Classic Series

Features factory-installed, traditional style trim to provide a

"framed" look. This series requires the installation of custom

panels that are not included.

KSSS36FTX KSSS42FTX KSSS48FTX

Overlay Series

Features factory-installed, overlay style trim to provide a

"frameless" look. This series requires the installation of custom

panels, handles, and standoffs.

KSSO36FTX KSSO42FTX KSSO48FTX

Side by Side Dispensing Refrigerators

Architect _ Series

Features wraparound styling that complements the contoured

door handles. This series provides a warm commercial-looking

built-in refrigerator.

KSSC36QTS KSSC42QTS KSSC48QTS

Overlay Series

Features factory-installed, overlay style trim to provide a

"frameless" look. This series requires the installation of custom

panels, handles, and standoffs.

KSSO36QTB KSSO42QTB KSSO48QTB

Classic Series

Features factory-installed, traditional style trim to provide a

"framed" look. This series requires the installation of custom

panels that are not included.

KSSS36QTB KSSS42QTB KSSS48QTB

KSSS36QTW KSSS42QTW KSSS48QTW

KSSS36QTX KSSS42QTX KSSS48QTX

iii i_ _i iiI

iii

I

E

Complete Series

Features factory-installed stainless steel trim and panels to create

a sleek, contemporary look.

KSSP36QTS KSSP42QTS KSSP48QTS

INSTALLATION REQUIREMENTS

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local

electrical inspector's use.

Tools Needed

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Cordless drill

• Drill bits

• Two adjustable

wrenches

• Phillips screwdriver

• Small level

• Appliance dolly

• Torx_tT27 screwdriver

• _Y32"Nut driver

• 3/8"and W' Open-end wrenches

• 8/32" Hex key

• 1/4"and _e" Socket drivers

• Tape measure

• Utility knife

Parts Needed

• Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

• One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

• Order factory panels, make custom panels or consult a

qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or

consult a qualified cabinetmaker or carpenter to make the

panels. See "Classic Series Custom Panels" for more

information.

Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See "Overlay

Series Custom Panels and Handle Kits" for more information.

Architect _ and Complete Series are shipped complete.

• If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need aferrule, a union, and a

V4"(6.35 mm) compression fitting.

The refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to

enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IM PORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall

below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs

(272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping

Radius."

• Location should permit door to open fully. See "Door Swing

Dimensions."

• Location must permit top grille removal. See "Opening

Dimensions."

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. Ifthe solid soffit is

higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to

the rear wall studs 80" to 90" (203 cm to 229 cm) above the

floor. See "Install Anti-Tip Boards" for more information.

NOTE: A clearance of V2"(1.3 cm) must be maintained above

the top grille in order for the top grille to be removed.

t®TORX is a registered trademark of Saturn Fasteners, Inc.

6

• A grounded 3 prong electrical outlet should be located within

a specified number of inches from the right-hand side

cabinets or end panel. See the chart following the graphic for

the number of inches required for your model. For more

information, see "Electrical Requirements."

• The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor or the

back wall. See "Water Supply Requirements" for more

information.

0

it

JJ JJ

ii 80"-g0"ii

i i(203-229 cm)ii

II

831/2" (212.1 cm) min.

843/4" (215 cm) max.

to bottom of solid soffit

A

Width

(see chart following)

/

ii

Dimension

77"

(196 cm)

r

t

I

(15.2 c

24"

(60.96 cm) rain.

Width A Width A for Dimension B

(as shown Overlay Models (as shown

Model above) (as shown above) above)

36 351/2"to 353/4'' 353/4'' to 36" 4" (10.2 cm)

(90.2 cm to (90.8 cm to

90.8 cm) 91.4 cm)

42 411/2"to 413/4" 413/4"to 42" 10" (25.4 cm)

(105.4 cm to (106 cm to

106 cm) 106.7 cm)

48 471/2'' to 473/4'' 473/4'' to 48" 16" (40.6 cm)

(120.7 cm to (121.3 cm to

121.3 cm) 121.9 cm)

NOTE: Flooring under refrigerator must be at same level as the

room. Face of cabinetry must be plumb.

£:i',1@CI: /_,,@;]!

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and flavor may be affected. If nuisance tripping has occurred,

and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, remove the top grille and turn the master

power switch to OFF or disconnect power at the circuit breaker

box.

When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

Allinstallationsmustmeetlocalplumbingcoderequirements.

Thewatershutoffshouldbelocatedinthebasecabineton

eithersideoftherefrigeratororsomeothereasilyaccessible

area.Theright-handsideisrecommended.Theaccesshole

throughthecabinetmustbewithin1/2"(12.7mm)oftherear

wall.

NOTE:Ifthewatershutoffvalveisinthebackwallbehindthe

refrigerator,itmustbeatananglesothatthetubeisnot

kinkedwhentherefrigeratorispushedintoitsfinallocation.

6"

(15.2 cm)

24"

(60.96 cm) min.

• If the water shutoff valve is not in the cabinets, the plumbing

for the water line can come through the floor. A 1/2"(12.7 mm)

hole for plumbing should be drilled at least 6" (15.2 cm) from

the right or left hand side cabinet or panel. On the floor, the

hole should be no more than 1" (2.54 cm) away from the back

wall. See "Connect the Water Supply."

• If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

• Do not use a piercing-type or 3/le"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

• If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Be sure there is adequate ceiling height to stand the refrigerator

upright when it is moved into place.

• The dolly wheel height must be added to the tipping radius

when a dolly is used.

• If needed, the tipping radius can be reduced. See "Reduce

Tipping Radius."

Side Tipping Radius

The side tipping radius varies depending upon the width of the

model. Use the chart provided to determine the side tipping

radius.

NOTE: Tip on side only.

/

//

/

//

/

//

/

ii ii

Model Tipping Radius A

36 901/2'' (229.9 cm)

42 93" (236.2 cm)

48 96" (243.8 cm)

8

Side View

• The depth from the front of the top grille to the back of the

refrigerator cabinet is 253A" (64.5 cm).

• The power cord is 84" (213 cm) long.

• The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long.

• Height dimensions are shown with leveling legs extended 1/8"

(3 mm) below the rollers.

"833/8"

(211.8 cm)

k

253/8"

---_

(64.5 cm)

231/2"

-_

(59.7 cm)

84" (213.4 cm)

Power Cord

+

"31/2" (8.9 cm)

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

Top View

A

Y

253/8''

(64.5 cm)

!

Model Width A

36 35" (88.9 cm)

42 41" (104.1 cm)

Front View

• Width dimensions were measured from trim edge to trim

edge.

• Height dimensions are shown with leveling legs extended 1/8"

(3 mm) below the rollers.

*83%"

(211.8 cm)

A

(seechart following)

Model Width A (Trim edge to trim edge)

36 361/4"(92.1 cm)

42 421/4'' (107.3 cm)

48 481/4"(122.6 cm)

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

48 47" (119.4 cm)

Thelocationmustpermitbothdoorstoopentoaminimumof

90°.Allow4W'(11.4cm)minimumspacebetweenthesideofthe

refrigeratorandacornerwall.

NOTE:Moreclearancemayberequiredifyouareusingoverlay

panels,customhandles,orextendedhandlesonaClassic

model.

Toadjustthedoorswing,see"AdjustDoors."

36" (91.4 cm) Models

107/8"

(27.6 cm)

443/8,,

(112.7 cm)

42" (106.7 cm) Models

<--167,/8 '' -_'" |

(42.9 cm) |

477/8,,

(121.6 cm)

48" (121.9 cm) Models

143/8"

(36.5 cm)

99 m)

(1

(48.9 cm)

513/8"

(130.5 cm)

10

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If

the refrigerator is to be installed close to the wall, see "Door Swing 90°,' on next page.

Door Swing 110 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

Hinge

®

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a

radius that is equal to at least half the

thickness of the panel if a 130° door swing is

desired. See "Adjust Doors."

Panel

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

11

I

90° Door

Stop Position

O

Hinge

jj_

Spacer Panel

Door Swing 90 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

,1

(2.5 cm)

3/4"

(1.9 cm)

/2 ',

(1.3,cm)i

,, ,,

i i

Cabin,'etr_/

1//2"

(1.30m)

3//4"

(1.90m) i

I 1"

(2.5cm)

0

<

"--II

m

,<

"0

11//4"

(3.2 cm)

11/2"

(3.8cm)

1/4"(6.35 mm)

1/2"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm)

Allow a minimum of 41/2"(11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if

thicker custom panels or custom handles are used. Do not overlook baseboards.

12

Custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen decor, and to use custom

handles for additional design flexibility.

The custom panels must have backer panels attached in order to

mount them to the refrigerator. It is most common to work with

three panels, as shown in the following graphic: a decorative

overlay panel, a V8" (3.18 mm) spacer panel or spacer strips and

a V4" (6.35 mm) backer panel.

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the

custom overlay panels will fit properly.

IM PORTANT:

• The weight of the refrigerator door overlay panel cannot

exceed 50 Ibs (23 kg).

• The weight of the freezer door overlay panel cannot exceed

40 Ibs (18.1 kg).

• The weight of the top grille overlay panel cannot exceed

10 Ibs (4.5 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips

around the perimeter in place of full-sheet solid spacer panels.

The spacer strips must be set in at least 1" (2.54 cm) from the

top, bottom and sides edges of the backer panel. If you use

spacer strips, it is also recommended that you use two 2"

(5.08 cm) strips horizontally centered for added support.

Overlay Panel

Spacer Panel

Backer Panel

(15.88 to Va,, (6.35 mm)

19.05 ram) (3.18 ram)

I Spacer Panel

Vs. _

'[]

ri,

l_ 1" minimum .

I (2.54 cm[. ......

I ,_'D'oer/Grille Trim

_*_ Offset Dimension

Overlay Panel

Backer Panel

Decorative Overlay Panel

Preferred

Radius

1/2,,

(1.27 em)

\

141/4"

(36.2 cm)

337/8 ''

(86.0em)

1

71/4" I

(18.4 cm)

÷

Freezer

DoorPanel

(Dispenser)

.,_-10_/a,,--_

(27.5em) 7 " DFre_zerIrP_

(183

Dispenser

cutout is

centered

left-to-right

Refrigerator

Door Panel

Model A B C

36 143/4"(37.47 cm) 193/4"(50.17cm) 343/4"(88.27cm)

42 17V4" (43.82 cm) 231/4" (59.06 cm) 403/4" (103.51 cm)

48 193/4" (50.17 cm) 263/4" (67.95 cm) 463/4" (118.75 cm)

*Represents placement of dispenser frame.

13

Backer Panels

NOTES:

• Dashed lines represent placement of backer panels on

overlay panels.

• Illustration shows backer panels placed on decorative

overlays.

63/16" I(15.7 cm)

Top Offset

_[" 15/a'' (4.13 cm)

....

22"

(55.9 cm)

-_ ..... III

331/4 '' '

(84.5 cm) ,

I

701/2''

(179.1 cm)

C

sF,---t - ' eOffset

Bottom Offset _ 1/2"(12.7 mm)

1/2" (1.27 cm) --

r_

Handle-

Side Offset

1/4,,

(6.4 mm)

701/2''

(179.1 cm)

_ . )'___.......

t Bottom Offset £ Bottom Offset __q&

1/8" (3.2 mm) 1/8" (3.2 mm)

Model D E F

36 141/4'' (36.20 cm) 191/4'' (48.90 cm) 333/4'' (85.73 cm)

42 163/4'' (42.55 cm) 223/4'' (57.79 cm) 393/4'' (100.97 cm)

48 191/4'' (48.90 cm) 261/4'' (66.68 cm) 453/4'' (116.21 cm)

Dispenser Frame (dispenser models only)

The dispenser frame attaches to the panel with 4 screws.

To remove the dispenser frame:

1. Remove the four screws attaching the frame.

2. Pull the dispenser frame from the decorative panel.

3. To replace the frame, hold the frame to the panel and replace

the screws.

/

A. Decorative panel

B. Refrigerator door

C. Dispenser frame

The dispenser frame overlaps the dispenser cutout by %e"

(0.78 cm) on each side and 1/2"(1.27 cm) on the top and bottom.

A A

A. ½" (1.27 cm) Overlap

14

Overlay Series Door Handle Kits

The following handle styles are available. Contact your

KitchenAid dealer or KitchenAid Parts and Accessories at

1-800-442-9991. In Canada, call 1-800-807-6777.

Architect _ Series

Handles

Part Number Color

4396103 Stainless Steel

8171760 Biscuit

4396105 White

4396106 Black

B C D

A. ArchitecP Series handle (4396103)

B. Flat end straight handle (4396776) with stainless steel

clamshell standoffs (4396775)

C. Round end arc handle (4396779) with bronze bullet

standoffs (4396778)

D. Round end semicircle (4396777) with stainless steel

cylinder standoffs (4396782)

Handles

These handles can be installed on side-by-side and bottom-

freezer refrigerators that require overlay panels.

Part Number Description

Satin Stainless Steel

4396781 Flat End Straight - 45" (114.3 cm) Length,

Satin Stainless Steel

4396777 Round End Semicircle,

Satin Stainless Steel*

4396779 Round End Arc,

Satin Stainless Steel*

*Availablefornon-dispensing models only.

Standoffs

The kit includes screws to support 3/4" applications.

Standoffs can be installed on side-by-side and bottom-freezer

refrigerators that require overlay panels.

NOTES:

• Two standoffs must be ordered for each handle.

• Handles and standoffs may be combined to meet your

individual decorating needs.

Part Number Description

4396775 Clamshell, Satin Stainless Steel

4396780 Clamshell, Satin Bronze

4396774 Bullet, Satin Stainless Steel

4396778 Bullet, Satin Bronze

4396782

4396773

Cylinder, Satin Stainless Steel

Cylinder, Satin Bronze

(.,lass:<: Is_@ttes :acI}}o w I: alset5 a:t_cI _'

All factory parts are available through your KitchenAid dealer or

by calling KitchenAid Parts and Accessories at 1-800-442-9991.

In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Three kits containing colored acrylic or stainless steel door and

top grille panels are available. Follow the kit instructions for

installing the panels.

NOTE: Panel kits are not required for factory-installed stainless

steel panel models.

Door Panel Part Numbers for Non-dispenser Models

Color 36 42 48

White #2325136 #2325137 #2325138

Black #2325139 #2325140 #2325141

Stainless Steel #2325142 #2325143 #2325144

Door Panel Part Numbers for Dispenser Models

Color 36 42 48

White #2325127 #2325128 #2325129

Black #2325130 #2325131 #2325132

Stainless Steel #2325133 #2325134 #2325135

Extended Door Handle Kits

Use extended door handles when additional finger clearance is

needed between the door handles and custom panel. Follow the

kit instructions for installing the door handles.

Color Part Number

White #4387990

Black #8171418

Stainless Steel #4388062

Matte Aluminum #4387989

15

If you plan to install custom wood panels, you will need to create

the panels yourself or consult a qualified cabinetmaker or

carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may

cause damage to your refrigerator.

NOTE: Dimensions shown have a (+)Vie" (1.5 mm) tolerance.

Panels that are more than V4"(6.35 mm) thick must be routed. If

panels are less than V4"(6.35 mm) thick, install a filler panel

between the doors and decorative panels.

Top Grille Panel

The top grille panel should not weigh more than 10 Ibs (4.5 kg).

NOTE: The dashed lines in the illustration represent the location

and offsets of raised wood panel.

7" i

(17.78 cm)

A _..i

-I

-_11 S_ide Offsets

-_ "17/16" (1.11 cm)

Top & Bottom Offsets___

1/4" thick 11/16"(1.75 cm)

plywood

Model A

36 34V4" (87.0 cm)

42 40V4" (102.2 cm)

48 46_A'' (117.5 cm)

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 40 Ibs (18.1 kg).

The refrigerator panel should not weigh more than 50 Ibs (23 kg).

_t_

7-

1/2,,

(1.27 cm)

W' thick .................

plywood

7/16" ._

(1.1 cm)/

I- ..... I

I

Freezer

Door

(Non-Dispenser)

I 1 I

, 3 V4'_..,

,(8.3 cm) i

I

.... t

_--B_

r

Refrigerator

Door

I 31/4.

(8.3 cm)

__t_

7-

1/2,,

(1.27 cm)

._ 7/16"

(1.1 cm)

V4"thick

plywood

T

_- W' Location and offsets W'

(1.27 cm) of raised wood panel (1.27 cm)

Model A B

36 141/4"(36.2 cm) 191/4"(48.9 cm)

42 163/4"(42.6 cm) 223/4"(57.8 cm)

48 19V4" (48.9 cm) 26V4" (66.7 cm)

NOTES:

• If the standard handle is used, the handle side offset of

both panels should be 3V4" (8.25 cm) to all for finger

clearance.

If an extended handle is used, the handle side offset of

both panels should be 7/le"(1.1 cm). Make sure the

refrigerator location allows the doors with extended

handles to open to 90 degrees. See "Door Swing

Dimensions."

The dashed lines in the illustration represent the location

and offsets of raised wood panel.

16

Door Panels for Dispenser Models

The freezer panel should not weigh more than 40 Ibs (18.1 kg).

The refrigerator panel should not weigh more than 50 Ibs (23 kg).

_t_

7-

1/2,,

(1.27 cm)

141/4"

(36.2 cm)

333/4"

(85.7 cm)

7/16" ..._

(1.1 cm)/

I

Freezer

Door

(Dispenser)

I

Dispenser

cutout is

centered

left-to-right

I

31/4,_,,

(8.3 cm) ,

I

_-- B -_

r-

Refrigerator

Door

_t

7-

1/2,,

(1.27 cm)

7/16"

(1.1 cm)

7-

1/2,, Location andoffsets 1/2,,

(1.27 cm) of raised wood panel (1.27 cm)

Model A B

36 141/4"(36.2 cm) 19W' (48.9 cm)

42 163/4"(42.6 cm) 223/4"(57.8 cm)

48 191/4"(48.9 cm) 26W' (66.7 cm)

NOTES:

Dispenser cutout is centered left-to-right.

If the standard handle is used, the handle side offset of

both panels should be 31/4'' (8.25 cm) to all for finger

clearance.

If an extended handle is used, the handle side offset of

both panels should be 7/le"(1.1 cm). Make sure the

refrigerator location allows the doors with extended

handles to open to 90 degrees. See "Door Swing

Dimensions."

The dashed lines in the illustration represent the location

and offsets of raised wood panel.

Dispenser Frame (Classic series dispenser models)

The dispenser frame attaches to the panel with 4 screws.

To remove the dispenser frame:

1. Remove the four screws attaching the frame.

2. Pull the dispenser frame from the decorative panel.

3. To replace the frame, hold the frame to the panel and replace

the screws.

A.Dispenser frame

The dispenser frame overlaps the dispenser cutout by 5/le"

(0.78 cm) on each side and 1/2"(1.27 cm) on the top and bottom.

A. ½" (1.27 cm) Overlap

17

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed at the end of a cabinet run. You

may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type

of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions

and may not reflect the needed panel installation

dimensions.

• The side panel should be a minimum of 1/2"(1.27 cm) thick

to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

'TT

241/8"

(61.3 cm)

(60.3 cm)

231/2"

(59.7 cm)

Side Trim

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add 7/32"(5.6 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than V4"(6.35 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

A

Recessed Inset Installation Dimensions

(6.35 mm)

11/64"

(4.5 mm)

(15.7 mm)

1. Measure the distance from point A (as shown) to the back

wall.

2. Route the front edge of the support board or attach a V4"

(6.35 mm) board to hold the panel in the cabinet side trim.

Custom side panels may be needed when not enough space is

available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed at the end of a cabinet run. You

may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type

of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions

and may not reflect the needed installation dimensions.

• The side panel should be a minimum of 1/2,,(1.27 cm) thick

to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

18

Refrigerator

SideTrim

3/8"

(9.7 mm)

1_611

(1.5 mm)

3/32"

(2.38 mm)

Overlay

t

2311/16 ''

(60.16 cm)

3/1611

(4.5 mm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add 1/32"(0.8 mm) to this measurement to allow the side

panel to fit into the trim.

2. If the panel is more than 3/8"(9.5 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a 3/8"

(9.5 mm) board to hold the panel in the cabinet side trim.

A I

¢--

INSTALLATION

INSTRUCTIONS

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

IM PORTANT:

• Do not remove the film covering until the refrigerator is in its

operating location.

• All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating location.

1. Remove and save the literature package bag taped to the

side of the refrigerator and the parts bag behind the grille.

Remove the four brackets (two on each side) that attach the

shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the

refrigerator is in its final location.

2. If necessary, reduce the tipping radius. See "Tipping Radius"

for ceiling height requirements or "Reduce Tipping Radius"

for step-by-step instructions. If you do not need to reduce the

tipping radius, proceed to "Move the Refrigerator into

House."

19

Before bringing the refrigerator into the home, be sure there is

adequate ceiling height to stand the refrigerator upright. See

"Tipping Radius" in the "Installation Requirements" section for

more information.

If you do not have adequate ceiling height to stand the

refrigerator upright, the tipping radius can be reduced by

removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm)

42 881/2'' (224.8 cm)

48 891/4'' (226.7 cm)

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the

grille on a soft surface.

B A B

3=

A. Top grille

B. Cabinet side trim

Remove the six screws attaching each cabinet side trim to

the refrigerator and remove the side trims.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

1=

Place an appliance dolly under the left side of the refrigerator

as shown. Place the corner posts from the packing materials

over the trims and handles as appropriate to avoid damage.

Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the

Architect ®Series.

[ I

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and

then lower the right-hand side of the refrigerator to the floor.

5. Reassemble the trim and top grille after the dolly has been

removed from the refrigerator.

kll_l I - I I!11);!I[dl S

........... i

To avoid tipping during use, the solid soffit must be within

1" (2.5 cm) maximum above the refrigerator. If the solid soffit

is higher than 1" (2.5 cm) or one is not available, then the

refrigerator must be braced.

• It is recommended that board(s) be installed before the

refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the

compressor cover.

• Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

• During installation, raise the refrigerator up so there is

1/4"(6.35 mm) maximum between the top of the refrigerator

and the bottom of the anti-tip board(s). Do not crush the

compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to

229 cm) above floor.

20

La page charge ...

KitchenAid KSSC42FTS18 Guide d'installation

Ce manuel convient également à

KitchenAid KSSC42FTS18 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents