Wacker Neuson RSS800A Manuel utilisateur

Operator’s Manual

Notice d'Emploi

Walk-Behind Rollers

RS 800A

RSS 800A

0403072 01 0411

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson Corporation

represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Manila Incorporated

Lot 2,Blk 1 Phase , PEZA Drive, First Cavite Industrial Estate, Brgy. Langkaan

Dasmariñas, Cavite, Philippines

Tel: +63-(0)2-580-7136 Fax: +63-(0)2-580-712

www.wackerneuson.com

Translated

instructions

This Operator’s Manual presents a translation of the original instructions. The original

language of this Operator’s Manual is American English.

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson Corporation

represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Manila Incorporated

Lot 2,Blk 1 Phase , PEZA Drive, First Cavite Industrial Estate, Brgy. Langkaan

Dasmariñas, Cavite, Philippines

Tel: +63-(0)2-580-7136 Fax: +63-(0)2-580-712

www.wackerneuson.com

Translated

instructions

This Operator’s Manual presents a translation of the original instructions. The original

language of this Operator’s Manual is American English.

RS 800 Table of Contents

wpm_bo5000191685_04TOC.fm 1

Foreword 3

1. Emission System Control Information 4

2. Safety Information 5

2.1 Operating Safety .................................................................................. 6

2.2 Operator Safety While Using Internal Combustion Engines ................. 7

2.3 Service Safety ...................................................................................... 8

2.4 Label Locations .................................................................................... 9

2.5 Safety Labels ...................................................................................... 10

3. Technical Data 13

3.1 Engine ................................................................................................ 13

3.2 Roller .................................................................................................. 14

3.3 Lubrication .......................................................................................... 14

3.4 Dimensions ......................................................................................... 15

4. Operation 16

4.1 Operation and Service Locations ....................................................... 16

4.2 Application .......................................................................................... 18

4.3 Recommended Fuel (RS 800A, RSS 800A) ...................................... 18

4.4 Before Starting ................................................................................... 19

4.5 To Start (RS 800A) ............................................................................. 20

4.6 To Stop (RS 800A) ............................................................................. 20

4.7 To Start (RSS 800A) .......................................................................... 21

4.8 To Stop (RSS 800A) ........................................................................... 21

4.9 Direction and Speed Control .............................................................. 22

4.10 Exciter (Vibration) Control .................................................................. 22

4.11 Watering System ................................................................................ 23

4.12 Handle Adjustment ............................................................................. 24

4.13 Operation on Slopes ........................................................................... 25

4.14 Rollovers ............................................................................................ 25

Table of Contents RS 800

wpm_bo5000191685_04TOC.fm 2

5. Maintenance 26

5.1 Maintaining the Emission Control System............................................26

5.2 Periodic Maintenance Schedule ..........................................................26

5.3 Lubrication ...........................................................................................27

5.4 Storage ................................................................................................29

5.5 Engine Oil ............................................................................................30

5.6 Air Cleaner ..........................................................................................31

5.7 Spark Plug ...........................................................................................32

5.8 Sediment Cup ......................................................................................32

5.9 Carburetor ...........................................................................................33

5.10 Scraper Bars .......................................................................................34

5.11 Cleaning the Machine ..........................................................................34

5.12 Lifting the Machine ..............................................................................35

5.13 Transporting the Machine ....................................................................36

5.14 Troubleshooting ...................................................................................37

5.15 Wiring Diagram (RSS 800A) ...............................................................39

wc_tx000001gb.fm 3

CALIFORNIA

Proposition 65 Warning:

Engine exhaust, some of its constituents, and certain vehicle

components, contain or emit chemicals known to the State of

California to cause cancer and birth defects or other reproductive

harm.

Foreword

This manual provides information and procedures to safely operate

and maintain this Wacker Neuson model. For your own safety and

protection from injury, carefully read, understand and observe the

safety instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker Neuson

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Neuson

Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Neuson Corporation

reserves the right to change any portion of this information without

notice.

All rights, especially copying and distribution rights, are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker

Neuson Corporation represents an infringement of valid copyrights

and will be prosecuted. We expressly reserve the right to make

technical modifications, even without due notice, which aim at

improving our machines or their safety standards.

WARNING

Emission Control System Information

4 wpm_tx001755gb.fm

1 Emission Control Systems Information and Warranty

The Emission Control Warranty and associated information is valid only for the

U.S.A., its territories, and Canada.

1.1 Emission Control Systems Warranty Statement

See the supplied engine owner’s manual for the applicable exhaust and

evaporative emission warranty statement.

1.2

RS 800 /... Safety Information

wpm_si000354gb.fm 5

2. Safety Information

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: Contains additional information important to a procedure.

DANGER

WARNING

CAUTION

Safety Information RS 800 /...

wpm_si000354gb.fm 6

2.1 Operating Safety

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

2.1.1 Never operate this machine in applications for which it is not intended.

2.1.2 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

2.1.3 Do not use accessories or attachments that are not recommended by

Wacker Neuson. Damage to equipment and injury to the user may

result.

2.1.4 Always wear protective clothing appropriate to the job site when

operating the machine.

2.1.5 ALWAYS remain aware of moving parts and keep hands, feet, and

loose clothing away from the moving parts of the machine.

2.1.6 Read, understand, and follow procedures in the Operator’s Manual

before attempting to operate the machine.

2.1.7 ALWAYS check that all controls are functioning properly immediately

after start-up! DO NOT operate machine unless all controls operate

correctly.

2.1.8 ALWAYS remain aware of changing positions and movement of other

equipment and personnel on the job site.

2.1.9 ALWAYS remain aware of changing surface conditions and use extra

care when operating over uneven ground, on hills, or over soft or

coarse material. The machine could shift or slide unexpectedly.

2.1.10 ALWAYS use caution when operating near the edges of pits, trenches

or platforms. Check to be sure ground surface is stable enough to

support the weight of the machine and operator and there is no danger

of the machine sliding, falling or tipping.

2.1.11 Always operate machine with all safety devices and guards in place

and in working order. Do not modify or defeat safety devices. Do not

operate machine if any safety devices or guards are missing or

inoperative.

2.1.12 ALWAYS position yourself safely when operating machine in reverse

or on hills. Leave enough space between yourself and the machine so

you will not be placed in a hazardous position should the machine slide

or tip.

WARNING

RS 800 /... Safety Information

wpm_si000354gb.fm 7

2.1.13 ALWAYS operate the machine with both of your feet on the ground!

DO NOT stand, sit, or ride on machine while in operation.

2.2 Operator Safety While Using Internal Combustion Engines

Internal combustion engines present special hazards during operation

and fueling. Read and follow the warning instructions in the engine

owner’s manual and the safety guidelines below. Failure to follow the

warnings and safety standards could result in severe injury or death.

2.2.1 Do not smoke while operating the machine.

2.2.2 Do not smoke when refueling the engine.

2.2.3 Do not refuel a hot or running engine.

2.2.4 Do not refuel the engine near an open flame.

2.2.5 Do not run the engine near open flames.

2.2.6 Do not run the machine indoors or in an enclosed area such as a deep

trench unless adequate ventilation, through such items as exhaust

fans or hoses, is provided. Engine exhaust contains carbon monoxide.

This is a poison you cannot see or smell. Exposure to carbon

monoxide can cause loss of consciousness and CAN KILL YOU IN

MINUTES.

2.2.7 Refill the fuel tank in a well-ventilated area.

2.2.8 Replace the fuel tank cap after refueling.

2.2.9 ALWAYS check the fuel lines and the fuel tank for leaks and cracks

before starting the engine. Do not run the machine if fuel leaks are

present or the fuel lines are loose.

2.2.10 ALWAYS keep the area around a hot exhaust pipe free of debris to

reduce the chance of an accidental fire.

WARNING

Safety Information RS 800 /...

wpm_si000354gb.fm 8

2.3 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

2.3.1 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

2.3.2 DO NOT remove air cleaner cover, paper element, or precleaner while

engine is running.

2.3.3 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

2.3.4 ALWAYS replace the safety devices and guards after repairs and

maintenance.

2.3.5 Replace worn or damaged components with spare parts designed and

approved by Wacker Neuson.

2.3.6 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

2.3.7 ALWAYS check all external fasteners at regular intervals.

2.3.8 ALWAYS make sure slings, chains, hooks, ramps, jacks, and other

types of lifting devices are attached securely and have enough weight-

bearing capacity to lift or hold the machine safely. Always remain

aware of the location of other people in the area when lifting the

machine.

2.3.9 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

2.3.10 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

2.3.11 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

2.3.12 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

WARNING

RS 800 /... Safety Information

wpm_si000354gb.fm 9

2.4 Label Locations

Safety Information RS 800 /...

wpm_si000354gb.fm 10

2.5 Safety Labels

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below.

Label Meaning

DANGER!

Engines emit carbon monoxide; operate only in

well-ventilated area. Read the Operator’s Man-

ual.

No sparks, flames, or burning objects near the

machine. Shut off the engine before refueling.

WARNING!

Hot surface!

CAUTION!

Read and understand the supplied Operator’s

Manual before operating this machine. Failure

to do so increases the risk of injury to yourself

and others.

CAUTION!

Use only clean, filtered diesel fuel.

NOTICE

Lifting point.

RS 800 /... Safety Information

wpm_si000354gb.fm 11

WARNING!

To prevent hearing loss, wear hearing protec-

tion when operating this machine.

Tie-down point.

Water Tank

Vibration control ON/OFF.

Control Lever:

Forward and reverse motion controlled by red

levers.

Grease points: Inspect and lubricate every 100

hours of operation.

Label Meaning

Safety Information RS 800 /...

wpm_si000354gb.fm 12

Hydrostatic Drive:

Engage / Disengage

A nameplate listing the model number, item

number, revision number, and serial number is

attached to each unit. Please record the infor-

mation found on this nameplate so it will be

available should the nameplate become lost or

damaged. When ordering parts or requesting

service information, you will always be asked

to specify the model number, item number,

revision number, and serial number of the unit.

This machine may be covered by one or more

patents.

Label Meaning

RS 800 /... Technical Data

wpm_td000358gb.fm 13

3. Technical Data

3.1 Engine

Engine Power Rating

Net power rating per SAE J1349. Actual power output may vary due to

conditions of specific use.

Part No. RS 800A

0630011

RSS 800A

0630012

Engine

Engine Type

4-stroke, overhead valve,

single cylinder

Engine Make

Honda

Engine Model

GX 340 K1 QA2 GX 340 K1 QAE2

Max. rated power @ rated speed

kW (Hp) 7.1 (9.5) @ 3600 rpm

Spark Plug

(NGK) BR 6ES

Electrode Gap

mm (in) 0.7–0.8 (0.028–0.031)

Operating Speed

rpm 2400

Valve Clearance (cold)

intake:

exhaust:

mm (in.) 0.15 (0.006)

0.20 (0.008)

Air Cleaner

type Dual Element

Engine Lubrication

oil

grade

SAE 10W30

Service Class SF, SG

Engine Oil Capacity

l (oz.) 1.1 (37)

Fuel

type Regular unleaded gasoline

Fuel Tank Capacity

l (qts.) 6.8 (7.2)

Technical Data RS 800 /...

wpm_td000358gb.fm 14

3.2 Roller

3.3 Lubrication

Item No.

RS800A

0630011

RSS800A

0630012

Roller

Weight

kg (lbs.) 450 (1000) 465 (1025)

Area capacity

m² (ft²) / hr. 2630 (28300)

Forward speed (max.)

m (ft) / min. 0–61 (0–200)

Reverse speed (max.)

m (ft) / min. 0–46 (0–150)

Vibration frequency

Hz (vpm) 70 (420)

Gradability

%15

Water tank capacity

l (gal) 30 (8)

Part No.

RS 800A

0630011

RSS 800A

0630012

Lubrication

Gear case

type / qty. SAE 90W Gear Lube Oil /

175 ml (6.0 oz)

Hydrostatic transmission

SAE 10W30 Class SE

Grease fittings

No. 2 EMB

RS 800 /... Technical Data

wpm_td000358gb.fm 15

3.4 Dimensions

Operation RS 800 /...

wpm_tx001253gb.fm 16

4. Operation

4.1 Operation and Service Locations

See Graphic: wc_gr003471

RSS 800A

RS 800A

Ref. Description Ref. Description

1 Handle locking pin 7 Exciter control

2 Sprinkler tube 8 Water fill cap

3 Water control valve 9 Fuel tank

4 Scraper bar 10 Lifting eye

5 Tie-down 11 Hydrostatic drive release

6 Forward/reverse control lever 12 Control box

Ref. Description Ref. Description

1 Handle locking pin 7 Exciter control

2 Sprinkler tube 8 Water fill cap

3 Water control valve 9 Fuel tank

4 Scraper bar 10 Lifting eye

5 Tie-down 11 Hydrostatic drive release

6 Forward/reverse control lever

RS 800 /... Operation

wpm_tx001253gb.fm 17

12

2

3 4

5

8

9

10

11

6

7

1

wc_gr003471

La page charge ...

Wacker Neuson RSS800A Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RSS800A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents