R03.001_03/01/2011
TECHNICAL FILE
Novojunta Pro® Decor
Novojunta Pro® Decor is a trim prole intended to be placed in
structural joints. It is made of anodized aluminium, 6063 alloy, with
a central body made of porous EPDM, which allows to absorb the
stresses and strains caused due to thermal variations in buildings. Its
face side is striated so it has non-slip properties. It is delivered pre-
ensambled and it is easy to install. It is available in color anodized
matt silver.
General Features
Material: Anodized aluminium
Lenght: 8ft2in / 2,5 m.l.
Dimensions: h: 0,78’ / 20 mm.
a1: 2,75’ / 70 mm.
a2: 0,47-1,18’ /12,6-30 mm.
Packaging: 10 u./box
Finishes:
Applications
Movement admitted
Buildings and constructive elements are under strains caused by thermal variations outdoors. The
installation of expansion joints helps to minimize the effects that these variations have in the hole
building, preventing the apparition of structural damage.
The CTE (Spanish Technical Code of Building), in the DB-SAE (Document about actions in building),
states that in steel or concrete buildings is necessary not to let continuous elements longer than forty
meters without installing expansion joints.
Novojunta Pro® Decor is a solution for structural joints made of an structure of anodized aluminium
and a central body made of EPDM. This prole absorb stresses and strains caused in constructive
elements, preventing the apparition of scratches or other damages. It can be place horizontal and
vertically both walls and oors. Its manufacturing, made of anodized aluminium certied by Qualanod,
allows its installation outdoors or indoors guaranteing a high resistances an durability.
Novojunta Pro® Decor is a suitable prole for its installation in Malls, parkings, airports and all kind
of public or private buildings. Its face side has the surface striated which gives it non-slip properties.
This makes the prole perfect for its installation in oors. Due to its size, it can be installed as a trim with
joint witdhs from 12,6 mm. up to 30 mm. (0,47’ - 1,18’).
Page 1 of 3
Joint width (a
2
) Expansion/contraction movements Total movement
12,6 mm. (0,47’) +/- 1,7 mm. (+/-0,04’) 3,4 mm. (0,11’)
30 mm.(1,18’) + 19.1 / - 8 mm. (+0,74’/-0,31’) 29,1 mm.(1,14’)
Model registered as a community design
Nº 869890-3
R03.001_03/01/2011
TECHNICAL FILE
Novojunta® Pro Decor
Supported loads
Novojunta Pro® Decor is able to support light loads.
It allows trafc category F, according to ACI (American Concrete Institute) Standards 302.1R-89 and
360.1R-92, for light vehicles with load <= 30 kN and <= 8 seats excluding the driver.
Trucks classication FL1 according to ACI (American Concrete Institute) Standards 302.1R-92 and
360.1R-92, with pneumatic or rigid wheels with net weight 21 kN and load up to 10 kN. It allows static
load lower than 1t/m
2
and the pass of vehicles with pneumatic wheels minor than 1t/axis, according to
the classication of light loads over oors (NTE-RSC).
Focused linear load 0,5 kN.
1. Apply silicone or a mastic in both toothed exterior sides of the body of Novojunta Pro® Decor.
2. Insert the Novojunta Pro® Decor in the hollow of the joint, ensuring it makes a good contact to
achieve a rmly union.
3. Clean the possible remaining material, remove the protective lm and let dry.
Technical Features
Installation
Materials
Page 2 of 3
This classication has been obtained from Standards ACI 302.1R-89 (Guide for concrete oors and
construction slabs, referring to the magnitude of the load they can support) and ACI 360.1R-92 (Design
of the different degrees of oors, which describe the six common types of oors for construction
referred to the actions induced by trucks and transport vehicles) and the classication of trucks
(depending on the net weight, dimensions and load which transport).
Aluminium
Novojunta Pro® Decor is placed once the installation of tiles in oor or wall is nished. This prole is
delivered ensambled and it is easy to install.
a) For joint width 12,6 mm. (0,47’)
Alloy: 6063 (AA and ASTM)
L-3441 (UNE 38-301-89)
Fire resistance: M0 (UNE 23-727-90)
Abrasion resistance: Very good
Lightfastness: Excellent
Appearance and color: EN 12373-1
Novojunta Pro® Decor is a prole made by extrusion of aluminium. The matt silver nish has been
anodized, improving mainly through this process their corrosion resistance, mechanical resistance and
appearance. The anodized applied has the quality seal Qualanod, which guarantees the quality of the
process and the resulting proles. This seal regulates several tests: appearance and color, thickness
measurements, sealing and impregnation control, abrasion resistance, lightfastness, acetic saline
chamber and nitric acid immersion.
Aluminium is a material with excellent chemical, physical and mechanical properties. It is lightweight,
tough, ductile, malleable and highly durable.
TECHNICAL FILE
R03.001_03/01/2011
You can nd more information about the technical features of the Emac®’s products by downloading
its Technical File in www.emac.es.
If you have any query, please contact our Technical Department in [email protected].
Technical Information
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
The data provided are for information only and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
Novojunta® Pro Decor
Cleaning and maintenance
Page 3 of 3
Novojunta Pro® Decor in joint width 12,6 mm. (0,47’)
1. Apply silicone or a mastic in one of the toothed exterior sides of the body of Novojunta Pro®
Decor.
2. Insert the Novojunta Pro® Decor in the hollow of the joint, ensuring it makes a good contact to
achieve a rmly union.
3. Clean the possible remaining material, remove the protective lm and let dry.
b) For joint width up to 30 mm (1,18’)
Novojunta Pro® Decor in width joint up to 30 mm. (1,18’) with xing.
c) If you want to ensure the xing of Novojunta Pro® Decor, you can do it through mechanical xing.
Si desea asegurar la jación de la Novojunta Pro® Decor puede hacerlo mediante jación mecánica.
Instale tacos tipo Fischer SX 6x30 o variante similar con tornillos de cabeza avellanada cada 40 cm. sólo
en uno de los laterales para permitir el libre movimiento del perl. Esta opción está especialmente
recomendada para la instalación del perl en fachadas.
The cleaning must be done periodically with a soft cloth. If you use a neutral liquid cleaner, you must
rinse the prole with cold water and dry to remove excess moisture. If dirtiness persists, clean the
prole with a solution with clean water and detergent or neutral soap 5%, brushing with a cloth that
has no particles that could scracht the nish.
Steel wool, abrasive cleaners, souring products as well as strong acids (hydrochloric and
perchloric),strong bases (caustic soda or ammonia) or carbonated solutions are not recommended.
Citric acid is neither recommended because disolves the protective layer of the surface of aluminium.
Waxes, petrolatum, lanolin or similar substances are not appropriate. Solvents containing haloalkanes
(hydrouoroether and chlorinated solvents) and curing accelerators containing chlorides should not be
used (use special accelerators free of chlorides).
Outdoors Indoors Wall tiling Floorings
-
1
-
2
-
3
dans d''autres langues
- English: Emac NJPDAL2070 Specification
Documents connexes
-
Emac NJPDAL2070 Guide d'installation
-
-
-
-
-
-
-
-