Arcam C30, P35, P1 Manuel utilisateur
- Catégorie
- Amplificateur d'instruments de musique
- Taper
- Manuel utilisateur
Pre Amplifier C30
Power Amplifier P35
Power Amplifier P1
Préamplicateur C30
Amplicateur de Puissance P35
Amplicateur de Puissance P1
Vorverstärker C30
Vollverstärker P35
Vollverstärker P1
22
3
English
Safety guidelines
CAUTION: To reduce the risk of electric shock, do not remove cover
(or back). No user serviceable parts inside. Refer servicing to qualified
service personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture.
The lightning flash with an arrowhead symbol within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
‘dangerous voltage’ within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
CAUTION: In Canada and the USA, to prevent electric shock, match
the wide blade of the plug to the wide slot in the socket and insert the
plug fully into the socket.
IMPORTANT SAFETY INSTRUCTIONS
This product is designed and manufactured to meet strict quality
and safety standards. However, you should be aware of the following
installation and operation precautions:
1. Take heed of warnings and instructions
You should read all the safety and operating instructions before
operating this appliance. Retain this handbook for future reference and
adhere to all warnings in the handbook or on the appliance.
2. Water and moisture
The presence of electricity near water can be dangerous. Do not use
the appliance near water – for example next to a bathtub, washbowl,
kitchen sink, in a wet basement or near a swimming pool, etc.
3. Object or liquid entry
Take care that objects do not fall and liquids are not spilled into the
enclosure through any openings. Liquid filled objects such as vases
should not be placed on the equipment.
4. Ventilation
Do not place the equipment on a bed, sofa, rug or similar soft surface, or
in an enclosed bookcase or cabinet, since ventilation may be impeded.
We recommend a minimum distance of 50mm (2 inches) around the
sides and top of the appliance to provide adequate ventilation.
5. Heat
Locate the appliance away from naked flames or heat producing
equipment such as radiators, stoves or other appliances (including
other amplifiers) that produce heat.
6. Climate
The appliance has been designed for use in moderate climates.
7. Racks and stands
Only use a rack or stand that is recommended for use with audio
equipment. If the equipment is on a portable rack it should be moved
with great care, to avoid overturning the combination.
8. Cleaning
Unplug the unit from the mains supply before cleaning.
The case should normally only require a wipe with a soft, damp, lint-
free cloth. Do not use paint thinners or other chemical solvents for
cleaning.
We do not advise the use of furniture cleaning sprays or polishes as
they can cause indelible white marks if the unit is subsequently wiped
with a damp cloth.
9. Power sources
Only connect the appliance to a power supply of the type described in
the operating instructions or as marked on the appliance.
10. Power-cord protection
Power supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords and plugs, and the point where they exit
from the appliance.
11. Grounding
Ensure that the grounding means of the appliance is not defeated.
12. Power lines
Locate any outdoor antenna/aerial away from power lines.
13. Non-use periods
If the unit has a standby function, a small amount of current will continue
to flow into the equipment in this mode. Unplug the power cord of the
appliance from the outlet if left unused for a long period of time.
14. Abnormal smell
If an abnormal smell or smoke is detected from the appliance, turn
the power off immediately and unplug the unit from the wall outlet.
Contact your dealer immediately.
15. Servicing
You should not attempt to service the appliance beyond that described
in this handbook. All other servicing should be referred to qualified
service personnel.
16. Damage requiring service
The appliance should be serviced by qualified service personnel when:
A. the power-supply cord or the plug has been damaged, or
B. objects have fallen, or liquid has spilled into the appliance, or
C. the appliance has been exposed to rain, or
D. the appliance does not appear to operate normally or exhibits a
marked change in performance, or
E. the appliance has been dropped or the enclosure damaged.
SAFETY COMPLIANCE
This product has been designed to meet the IEC 60065 international
electrical safety standard.
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
ATTENTION
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
22
3
English
Using this handbook
Thank you for buying this quality Arcam product.
This handbook is for the following items:
C30 pre-amplifier
P35 power amplifier
P1 power amplifier.
The handbook is designed to give you all the information you need to
install and use these products. The C30 is described first, followed by
the P35 and the P1. Use of the CD-389 remote control supplied with
the C30 is also described.
If your amplifier(s) have been installed and set-up by an authorised
Arcam dealer, you may wish to go directly to the sections on how to
use this equipment. Otherwise we recommend reading the installtion
instructions carefully for your product before proceeding.
SAFETY
Safety guidelines are set out on the page 4 of this handbook.
Many of these items are common sense precautions, but for your own
safety, and to ensure that you do not damage the unit, we strongly
recommend that you read them.
OTHER LANGUAGES
If you would like this handbook in another language, either visit
our web-site (www.arcam.co.uk), or ask your dealer. Most of our
handbooks are available in a number of different languages.
CONTENTS
Safety guidelines............................................................................. 2
Important safety instructions...........................................................2
Safety compliance...................................................................................2
Using this handbook...................................................................... 3
Installation: C30 pre-amplier..................................................... 4
Positioning the unit................................................................................4
Connecting to a power supply .......................................................4
Power amplier connection ............................................................4
Connecting to other equipment....................................................5
Front panel controls..............................................................................6
Using your C30 pre-amplier ..................................................... 6
Recording....................................................................................................7
Setting up your C30 pre-amplier............................................. 8
Using the remote control............................................................ 9
Installation: P35 and P1 power ampliers...............................10
Positioning the unit............................................................................. 10
Connecting to a power supply ....................................................10
Connecting to other equipment................................................. 11
Connecting loudspeakers................................................................11
Remote switching................................................................................11
Three channel option (P35 only)...............................................11
Using your power amplier.......................................................12
Bi-wiring and bi-amping loudspeakers.....................................13
Before you start ................................................................................... 13
Bi-wiring your loudspeakers.......................................................... 13
Bi-amping your system......................................................................13
Technical specications...............................................................14
Remote-control codes ...............................................................15
Guarantee......................................................................................16
Service information.....................................................................16
On-line registration ............................................................................ 16
44
5
English
POSITIONING THE UNIT
Place your amplifier on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space
such as a bookcase or cabinet as both of these will impede air flow
through the unit.
CONNECTING TO A POWER SUPPLY
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed,
it must be disposed of immediately and securely, as it is a potential
shock hazard when inserted into the mains socket. Contact your
Arcam dealer if you need a new mains lead.
WRONG PLUG?
Before plugging in, check that the plug supplied with the unit fits your
supply and that your mains supply voltage agrees with the voltage
setting (115V or 230V) indicated on the rear panel of the unit
2
.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer.
This product must be earthed.
PLUGGING IN
Push the plug (IEC line socket) of the power cable supplied with the
unit into the socket (POWER INLET)
1
in the back of the unit. Make
sure it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
STAND-BY POWER
For remote stand-by operation, the amplifier’s control power supply is
kept powered up all the time the unit is connected to the mains supply.
The front panel power switch powers down all other circuitry. Power
consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
Installation: C30 pre-amplier
LR
PHONO
POWER INLET
PRE OUT
BUFFERED
L
R
L
R
L
R
VOLTAGE
SELECT
RECORD
OUT
PLAY
IN
TAPE/PROC
RECORD
OUT
PLAY
IN
VCR/TAPE 2 DVD AV TUNER CD AUX
MM
MC
REMOTE
IN
TRIG
OUT
115/230V
DIRECT
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket.
POWER AMPLIFIER CONNECTION
PRE OUT
456
– The recommended connection between
the C30 pre-amplifier and your power amplifier depends on both the
distance between the two and the type of power amplifier that you are
using. There are three options:
1. If the cables to be used to connect the C30 to the power
amplifier are less than 3m long, we recommend connecting the
DIRECT sockets
6
to the input sockets of your power amplifier.
On the P35 and P1, connect to the socket(s) labelled AUDIO IN.
If the cables to be used to connect the C30 to the power amplifier
are 3m or longer, then the connection to use depends on the type of
power amplifier you have.
2. If your power amplifier does not have balanced inputs (such as
the P35), use the BUFFERED outputs
5
. On the P35, connect to
the sockets labelled AUDIO IN.
3. If your power amplifier provides balanced inputs (such as the P1),
use the balanced outputs
4
. On the P1, connect to the sockets
labelled BALANCED AUDIO IN.
The buffered and balanced outputs are designed to drive longer cables
than the direct output. Note that using the buffered outputs to drive
the P1 does not degrade the signal and will in no way damage either
piece of equipment.
44
5
English
CONNECTING TO OTHER EQUIPMENT
When connecting to other pieces of equipment, please note the
following:
The use of high quality interconnect cables to and from your
amplifier is recommended to ensure the best sound quality. Your
dealer will be able to recommend interconnect cables that are
suitable for your system.
All the line inputs (except for the PHONO input) have the same
sensitivity and may be used with equipment other than that
labelled, if needed.
The C30 provides the following connections:
TAPE/PROC RECORD OUT
7
– Connect these output sockets
to the input sockets of your cassette deck (usually labelled RECORD on
the cassette deck).
TAPE/PROC PLAY IN
8
– Connect these input sockets to the
output sockets of your cassette deck (usually labelled PLAY on the
cassette deck). If you do not have a cassette deck you can use this input
for other (line level) equipment, such as a CD player, tuner, VCR, etc.,
(but not for a turntable).
VCR/TAPE2 RECORD OUT
9
– These output sockets can be
connected to the input sockets of VCR (usually labelled RECORD on
the VCR). Alternatively, these outputs can be connected to a second
recording device (such as a second cassette deck).
VCR/TAPE2 PLAY IN
bk
– Connect these input sockets to the
output sockets of your VCR/second recorder (the output sockets are
usually labelled PLAY). Alternatively, you can use this input for other (line
level) equipment such as a CD player, tuner, etc., (but not a turntable).
DVD
bl
– Connect this input to the stereo audio outputs of a DVD
player.
AV
bm
– Connect this input to the stereo audio outputs of audio
visual equipment such as a laserdisc player, satellite or Nicam tuner.
TUNER
bn
– Connect this input to the audio outputs of your radio
tuner.
CD
bo
– Connect this input to the audio outputs of your CD player
or DAC (digital to analogue converter).
AUX
bp
– As the C30 has the phono board fitted as standard, the
AUX connection is a line level output carrying an equalised phono
signal. If desired, this output can be connected to a recording device.
Should you wish to remove the phono board, then the AUX connections
can be used as a line input. Please see your dealer for further information
about this option, as removing the phono board yourself may invalidate the
warranty.
PHONO
bq
– Connect this input to the audio outputs of your
turntable. The phono module supplied with the C30 is compatible
with most moving magnet and moving coil cartridges. Set the blue
switch immediately below these connections to the correct setting,
as follows:
MM – is used for high output moving coil and all moving magnet
cartridges. The blue switch is flush with the rear panel of the
C30.
MC – is used for low output moving coil cartridges. The blue switch
is depressed inside the rear panel of the C30.
Phono earth terminal – For connecting your turntable earth lead
(if fitted). Note that this terminal must not be used as a safety earth.
TRIG OUT and REMOTE IN
3
(12V in and out) – These
connections are intended for use in multi-room installations.
TRIG OUT – This output provides a 12V signal whenever the unit is
switched on (i.e., not off or in standby). This signal can be used to
switch on automatically power amplifiers (or other equipment)
connected to the C30, as they will come on when the C30 is
activated. This is useful if the power amplifier is remote from the
C30, or otherwise difficult to access. This feature can be used
with both the P35 and the P1. If you are bi-amping with a power
amplifier and wish to power both units on or off simultaneously,
see page 11.
REMOTE IN – This allows remote control signals to be received by the
C30 if the remote sensor is covered (or otherwise not ‘visible’ to
the remote control). An external sensor is used to receive the
signals from the remote control, which are then fed to the C30
(into this input) using a suitable cable. Remote control signals
acceptable to the C30 must be in modulated RC5 format, with
a voltage level of between 5V and 15V.
Note that in normal use there is no need to make any connections to
these sockets. If you would like to make use of these features, please
contact your dealer for more advice on how to make the connections
and on what type of cable to use.
66
7
English
Using your C30 pre-amplier
FRONT PANEL CONTROLS
This section describes how to operate your amplifier.
If your amplifier has not been installed for you, you should first read the
section ‘Installation: C30 pre-amplifier’ on page 5.
POWER
bn
Switches the unit on and off.
The power indicator light (directly above the switch) shows the status
of the amplifier. A red light means the amplifier is in stand-by mode
(press the POWER/STANDBY button on the remote control, or the
POWER button on the front panel, to switch between stand-by and
powered-up modes).
Remote control receiver
1
The remote control’s infrared receiver is positioned behind the ‘FMJ’
badge. Ensure the receiver is in a clear line of sight from the remote
control to allow signals to be received.
MODE
2
, UP and DOWN
5
These buttons are intended for use with any future optional modules
that may become available for the C30. The UP and DOWN buttons,
however, are used with the existing C30 pre-amplifier to move the
cursor when customising the ‘Welcome message’ (see page 9).
Control knob
7
, SELECT
4
and ENTER
6
The control knob has two functions:
as a volume control, to adjust the output of the headphones and
of the pre-amp output (PRE OUT).
when used in conjunction with the SELECT and ENTER buttons, to
customise amplifier settings (see page 9).
VOLUME CONTROL SETTINGS
It is important to realise that volume level shown on the display is not
an accurate indication of the power delivered to your loudspeakers. The
amplifier often delivers its full power long before the volume control
reaches its maximum position, particularly when listening to heavily
recorded compact discs. However the amplifier also has to be capable of
giving full power output from much lower level sources, such as tuners
and cassette decks. Using these sources, the volume control setting may
be much higher before distortion (audible overload) sets in.
It is possible to compensate for these input level differences by using
the ‘Input trims’ menu item. See page 9 for further details on how to
do this. Adjusting the input levels of each source individually will help to
avoid accidental overload.
Source selectors
8
These buttons select the source connected to the corresponding input.
A light above the relevant button indicates which input is currently
selected and it will also usually be shown on the display. See page 6 for
more information on connecting audio sources to the C30.
TONE
9
Switches the tone circuits on and off, including settings for individual
sources. Note that the tone LED does not light unless a tone setting has
been made. See page 9 for further information on the tone controls.
MUTE
bk
Silences all main analogue outputs when selected.
DISPLAY
bl
This switches the display brightness between Off/
Dim/Bright. This is provided to set the display brightness to a level
that is comfortable for you. Switching the display off may give a small
improvement in sound quality.
PHONES
bm
This 1/4-inch stereo jack plug socket accepts headphones with an
impedance rating between 32Ω and 600Ω.
The headphone socket is always active. To avoid possible damage, always
disconnect headphones prior to switching the amplifier on or off.
C30 PRE-AMPLIFIER
MUTE DISPLAY POWERPHONES
PHONO/AUX
CD TUNER AV DVD
VCR TAPE TONE
ENTER
MODE RECORD SELECT
66
7
English
RECORDING
With the C30 it is possible to listen to and record from one source, or
to listen to one source while recording another.
Both sets of tape sockets are identical in sensitivity and suitable for use
with almost any type of recorder (cassette, CDR, MD, VCR, reel-to-
reel, etc.). The record signal is sent to both the TAPE and VCR output
sockets.
RECORD
3
To record the currently selected source, press RECORD until the display
shows ‘RECORD SOURCE’. After a few seconds the display reverts to
showing the volume level and you are ready to record.
To listen to one source while recording another, press RECORD again
until the display shows ‘RECORD’ followed by the name of an input (e.g.
‘AUX’, ‘CD’, ‘TUNER’, etc.). Now press the source selector button on the
front panel for the source you wish to record. Your selection is shown
on the display for a few seconds, after which it reverts to showing the
volume level and you are ready to record.
The RECORD button can also be used as a second zone selector, sending
a source signal at line level to a second amplifier operating in another
room. If you need help with this, contact your Arcam dealer or Arcam
customer support.
TAPE-TO-TAPE COPYING (DUBBING)
You can perform tape dubbing from VCR to TAPE, but not from TAPE
to VCR.
For example, to copy from a cassette recorder connected to the VCR/
TAPE2 socket to a cassette recorder connected to the TAPE socket, first
use the RECORD button as explained above and select ‘RECORD VCR’.
This routes the VCR signal to the TAPE output.
Set the cassette recorder connected to the TAPE socket into its record
mode and the other to playback mode to start dubbing.
TAPE
8
To play back the recording from a cassette deck attached to the TAPE
input, press TAPE. ‘TAPE’ is shown on the display. Selecting this input
overrides the other source selectors.
It is also possible to monitor a recording while it is being made, provided
your cassette deck is a 3-head type. To do this, press TAPE. Pressing this
button on/off allows an A/B comparison between the source signal and
the recorded signal.
88
9
English
Setting up your C30 pre-amplier
LEFT RIGHT
–dB +dB
–dB +dB
‘Switch on’
state
–dB +dB
Volume Resolution – Standard,
fine or Reference. ‘Standard’ and
‘Fine’ represent different levels of volume
control sensitivity. The ‘Reference’ setting
gives absolute increments in 0.5dB steps.
Volume display mode – graphic
or numeric shows the volume either
as a bar graph or as a number. If Volume
resolution is set to ‘Reference’ a numeric
volume display shows the actual decibel
figure.
Input Trims – use the source select
buttons and Control knob to set input
trims for each source. Input trims are used
to compensate for variations in output
levels of different source equipment.
Max. ‘On’ Volume – This can be used to
limit the maximum volume the amplifier
operates at when it is first switched on.
The system comes on at this volume if
the last used volume exceeds this value.
If this is set to ‘Disabled’, the amplifier
comes on at the last used volume.
Tone Control – Global or Per
source. This specifies the scope of
changes for ‘Bass’ and ‘Treble’ tone settings.
The default setting is ‘Global’ which affects
all inputs equally. ‘Per source’ allows you
to set tone controls for individual inputs:
once set, the amplifier remembers tone
settings for each input.
Processor Mode – This mode enables
you to adjust the gain of the amplifier. The
amplifier can then be used to drive the
front left and right speakers in a surround
sound system when fed from a separate
processor. The volume of the entire
system can then be controlled using
the processor. Feed the sound from the
processor into the TAPE input. Set the
gain to match the amplifiers that drive
your other loudspeakers.
Welcome message – You can change
the power on ‘Welcome message’ from
‘Arcam Amp’ to display your name,
postcode, etc. When customising the
message, use the UP and DOWN buttons
to select the cursor position and the
Control knob to change the letter.
Phono/Aux Text – The C30 is fitted
with a phono module, so when the
phono input is selected as the source,
‘PHONO’ is displayed. Should you wish to
remove the phono board, then the AUX
connections can be used as a line input.
In this case, change the text displayed to
‘AUX’, using this menu option.
Restore Settings – this restores all
amplifier settings, including input trims
and the welcome message, to their
factory defaults.
INTRODUCTION
The C30 allows you to adjust listening
settings to suit your taste, and to
customize various features of the
amplifier to fit your system. Use this
diagram to help you navigate through the
settings available.
The ENTER and SELECT buttons from
the front panel are represented in the
diagram by the symbols and
respectively.
The Control knob is shown as .
ADJUSTING LISTENING
SETTINGS
The default display mode is VOLUME,
where the Control knob is used to adjust
the sound level.
Press SELECT once to enter edit mode,
then repeatedly to cycle through the
other sound settings: BALANCE, BASS
and TREBLE. When a setting is selected
(shown on the display), it can be adjusted
by using the control knob. Press ENTER
to store the change you have made and
return to default (volume) mode, or press
SELECT again to move to the next setting.
CUSTOMISING AMPLIFIER
SETTINGS
It is possible to customise (change to your
preference) many of the features of the
C30. To do this, proceed as follows:
1. Press SELECT repeatedly until the
display shows ‘CUSTOMISE->’;
2. Rotate the Control knob to
choose which setting you wish to
alter;
3. Press SELECT to adjust the chosen
setting with the Control knob;
4. Press ENTER to confirm the
adjustment, or press SELECT to
confirm the adjustment and move
on to the next item.
Press ENTER twice to leave the Customise
menu.
88
9
English
Using the remote control
NOTE
Remember to install the two AAA batteries supplied
before trying to use your remote control.
Do not place anything in front of the FMJ badge on
the top left of the C30 (where the IR receiver is
located), or the remote control may not work.
CR-389 Remote Control
The CR-389 remote control gives access to all functions available on
the front panel of the C30. It also has controls to operate Arcam CD
players, AM/FM tuners and DAB tuners. The remote control transmits
Philips RC-5 type codes.
FM DAB
PROG DISP
RPT
MODE BAND
1-9 2-10 3-11
FM
DAB
SEL
TUNER
CR-389
CD
AMPLIFIER
VCRDVD TAPEAV
TUNERCDAUXPHONO
ENTER
SP1
SP2
DISP
MENU DISP
4-12
5-13 6-14 7-15 8-16
TUNER
These buttons are used to control tuner functions.
Note that the FM/DAB lights indicate into which mode you are
switching the remote control. The lights only illuminate for five
seconds to conserve battery power.
If neither light is illuminated this does not mean that the
remote control is not working!
(UP and DOWN)
Perform the same function as the buttons on the front
panel (see page 7).
SELECT
Performs same function as the SELECT button on the front
panel. It allows you to use the remote’s volume switch in the
same way you use the control dial on the front panel – to
adjust various amplifier settings (see page 7).
Note that pressing + corresponds to turning the
Control knob clockwise, – to anticlockwise.
ENTER
Performs the same function as the ENTER button on the front
panel (see page 7).
Source selection buttons
These operate in the same way as the source selectors on the
front panel of your C30.
Power/Stand-by
Toggles the amplifier between stand-by mode and full power
mode. The power indicator light next to the power button on
the front panel is red if the amplifier is in stand-by, amber while
the amplifier is powering up (this only takes a few seconds) and
green when the amplifier is powered up.
SP1 and SP2
These buttons are for use with the P35 amplifier, to allow you
to select and deselect the main (SP1) and secondary (SP2) sets
of speakers attached to it (see page 13 for further information).
DISP (display)
Cycles through the settings ‘Off’, ‘Dim’ and ‘Bright’. Turning the
display ‘Off’ may give a slight improvement in sound quality.
Volume and (mute)
Press + to increase volume or – to decrease the output volume
of the amplifier.
Press to mute the pre-amp outputs of the C30. Note that
both tape outputs and the headphone socket will remain active.
Mute is disabled either by pressing again, or by adjusting the
volume.
You can use the remote’s volume control in conjunction with
the SELECT button to adjust balance, tone and amplifier settings.
CD controls
These offer basic control of Arcam CD players
1010
11
English
POWER INLET
OUT
VOLTAGE
SELECT
230V
GAIN
XLR/
PHONO
TRIG
OUT
REMOTE
IN
4 – 16 OHMS
–
+
SPEAKERS
–
+
AUDIO
IN
P1
ARCAM
XLR
PHONO
BALANCED AUDIO
OUT
IN
Installation: P35 and P1 power ampliers
POSITIONING THE UNIT
Place your amplifier on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space
such as a bookcase or cabinet as both of these will impede air flow
through the unit, which is necessary for cooling.
CONNECTING TO A POWER SUPPLY
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed, it
must be disposed of immediately and securely, as it is a potential shock
hazard when inserted into the mains socket. Should you require a new
mains lead, contact your Arcam dealer.
WRONG PLUG?
Check that the plug supplied with the unit fits your supply and that your
mains supply voltage agrees with the voltage setting (115V or 230V)
indicated on the rear panel of the unit before plugging in.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer.
This product must be earthed.
PLUGGING IN
Push the plug (IEC line socket) of the power cable supplied with the
unit into the socket (POWER INLET) in the back of the unit. Make sure
it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
STAND-BY POWER
For remote stand-by operation, the amplifier’s control power supply is
kept powered up all the time the unit is connected to the mains supply.
The front panel power switch powers down all other circuitry. Power
consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket
IMPORTANT:
Ensure that the amplifier is switched off before attempting to
connect the speakers, and check carefully any connections made
before turning the unit back on.
P35 POWER AMPLIFIER: REAR PANEL
P1 POWER AMPLIFIER: REAR PANEL
+ R/CH1 –
CTR/CH3
SP1
SP2
POWER INLET
OUTIN
L
R
VOLTAGE
SELECT
230V
4 – 16 OHMS
+ L/CH2 –
+ R/CH1 –
+ L/CH2 –
AUDIO
SP1
SP2
4 – 16 OHMS
+ CTR/CH3 –
+ CTR/CH3 –
AUDIO
IN
OUT
LINK
REMOTE
IN
TRIG
OUT
Optional Third Channel
Module – provides a third
90W channel suitable for
Home Cinema or multi-
channel audio use.
1010
11
English
CONNECTING TO OTHER EQUIPMENT
The P35 and P1 amplifiers provide the following connections:
AUDIO IN (P35)
AUDIO IN and BALANCED AUDIO IN (P1)
Connect one of these inputs to the output sockets of your pre-
amplifier or the PRE OUT sockets of an integrated amplifier. Please read
the notes on page 5, which give information on the type of connection
that should be used to connect your pre-amplifier and power amplifier
together.
MONO LINK (P35) – The P35 power amplifier can be adapted to
provide two mono loudspeaker outputs from a single input. Pull out
the link supplied and use it to connect the L and R AUDIO OUT sockets
together. Using one power amplifier per loudspeaker will enable you
to bi-amplify bi-wireable loudspeakers. This is particularly beneficial
for top quality stereo installations with a separate pre-amplifier, or
where amplifiers are provided for the left, centre and right channel
loudspeakers in a five speaker Dolby Pro Logic or Dolby Digital
system.
If you wish to take advantage of this feature, please contact your Arcam
dealer for more information.
INPUT SELECTOR SWITCH (P1) – This switch allows either
unbalanced signals (through the phono connector) or balanced signals
(through the XLR connector) to be selected. The switch should be
pressed in to select the phono inputs and out to select the XLR
connector. Note that only one type of input connector will be switched
to the input of the amplifier; if you select (for example) the XLR
connector, then you will not be able to hear signals connected to the
phono inputs.
AMPLIFIER GAIN SWITCH (P1) – This switch is to allow the gain
of the P1 amplifier to be changed to suit your system requirements.
Two settings are available: with the switch in the IN position the gain is
set to standard ARCAM gain of 31.5dB. This allows the P1 to be used
in systems where there are other ARCAM power amplifiers. When the
switch is set to OUT then the gain is set to ‘THX standard gain’. In this
mode it can be used in systems containing amplifiers with THX gain (for
example, the P7).
DAISY CHAINING
Both the P35 and the P1 can also be connected to further power
amplifiers to drive more speakers (e.g., those in other rooms or tri-
amplified speakers, etc). This technique is called ‘Daisy chaining’.
To daisy chain power amplifiers, connect the AUDIO OUT sockets on the
power amplifier to the input of the extra power amplifier – left to left
and right to right.
CONNECTING LOUDSPEAKERS
The red and black terminals on the back of the amplifiers are used to
make the connections to the loudspeakers. It is possible to connect two
pairs of speakers; the pair designated “speaker 1” (SP1) are connected
to the lower set of terminals, while the pair designated “speaker 2” (SP2)
are connected to the upper set of terminals.
When connecting the speaker terminals of the amplifier with the
terminals on the speakers make sure that like polarities are matched
(i.e., match “+” with “+” (usually red) and “–” with “–” (usually black)).
Mismatching of polarities will result in a weak central sound, unclear
orientation of the instruments and the sense of direction of the stereo
being impaired.
There are two options for connecting the speaker cable to the
amplifier:
USING BARE WIRE ENDED LEADS:
1. Strip back the insulation on the wire to reveal about 2cm of
conductor (the metal inside the cable).
2. If the conductor is stranded, twist the strands together tightly to
avoid loose strands making contact with the adjacent terminals
or the back panel.
3. Loosen the terminal by turning it anti-clockwise
4. Insert the twisted wire through the hole in the terminal.
5. Tighten by turning clockwise.
When making connections with stranded bare ended wires, take great
care that no individual strands of wire come into contact with the
adjacent terminals or with the back panel. If this should happen, it will
cause a short circuit on the output of the amplifier and could damage
the amplifier.
USING SPADE TERMINALS:
1. Loosen the terminal by turning it anti-clockwise
2. Insert the spade connecter under the terminal.
3. Tighten by turning clockwise.
REMOTE SWITCHING
By making a connection from the TRIG OUT socket of the C30 pre-
amplifier to the REMOTE IN socket of the P35/P1 power amplifier, you
can use the C30 to switch the power amplifier on and off. If configured
in this way, the front panel POWER button of the C30 (or the POWER/
STANDBY button on the remote control) switches both amplifiers on
and off together. This facility allows you to conceal the power amplifier
yet still control it.
The connecting cable required is a 3.5mm to 3.5mm jack lead (stereo
or mono) and it is possible to connect several power amplifiers to C30
by ‘daisy chaining’ from TRIG OUT of one P35/P1 into the REMOTE IN of
the next.
THREE CHANNEL OPTION (P35 ONLY)
The P35 power amplifier can be upgraded from stereo to three
channels by adding a “third channel module”. (If this is performed, the
model is called the P35/3.)
The module offers extra loudspeaker terminals together with a third
set of AUDIO IN and OUT phono sockets and converts the P35 into
a 3 x 90W (RMS per channel into 8Ω) amplifier suitable for Home
Cinema or multi-channel audio use (such a unit may be used to amplify
left, right and centre channels in a multi-channel system, for example).
If you wish to take advantage of this feature, please contact your Arcam
dealer for more information.
1212
13
English
Using your power amplier
POWER (AND POWER INDICATOR LIGHT)
This button switches the unit on and off. The light indicates the status
of the amplifier.
When you switch your amplifier on, the light glows amber for a few
seconds, during which time the speakers are disconnected. The light
changes to green when the amplifier is ready for use. A red light means
the amplifier is in standby mode.
FAULT INDICATIONS
The power light may flash if a fault has occurred, with the colour of the
flashing light indicating the nature of the fault:
green – a D.C. offset fault has occured
amber – a thermal fault has occured (the P35/P1 is too hot)
red – a short circuit fault has occured (this can happen if the speaker
cables are not connected correctly and are making contact with
each other or with the chassis)
red and amber – more than one fault has occured.
Except for a thermal fault, if one of the above faults is detected by
your amplifier the unit waits for six seconds before checking to see if
the fault has cleared. If the fault clears within six seconds, then the unit
continues operation; otherwise the unit shuts itself down. In the case of
a thermal fault, the unit waits until its sensor temperature lowers before
resuming operation.
If the amplifier has shut itself down, you should unplug the amplifier and
leave it for a few minutes before reconnecting. If the fault cannot be
cleared, unplug your amplifier and contact your Arcam dealer.
P35 POWER AMPLIFIER
SP1 SP2 POWER
NOTE: If both lights are out the amplifier will appear not to work,
as all speakers are switched off.
SP1 AND SP2 (P35 ONLY)
These buttons allow you to switch on and off the main (SP1) and
secondary (SP2) sets of speakers attached to your amplifier. If the
indicator light (the light above the switch) is on, it shows that the
output for the speaker is switched on. If no secondary set of speakers is
connected, we recommend that this output be switched off.
P1 POWER AMPLIFIER
POWER
P35 POWER AMPLIFIER: FRONT PANEL
P1 POWER AMPLIFIER: FRONT PANEL
1212
13
English
Bi-wiring and bi-amping loudspeakers
BEFORE YOU START
WARNING: Do not make any connections to your amplifier while
it is switched on or connected to the mains supply.
Before switching on please check all connections thoroughly, making
sure bare wires or cables are not touching the amplifier in the wrong
places (which could cause short circuits) and you have connected
positive (+) to positive and negative (–) to negative.
Always ensure that the volume control on your amplifier is set to
minimum before starting these procedures.
BI-WIRING YOUR LOUDSPEAKERS
Bi-wiring improves the sound of your system because it divides the
high and low frequency signal currents into separate speaker cables.
This avoids signal distortions arising from the high and low frequency
currents interacting with one another within a single cable, as in
conventionally wired systems.
You will need:
Speakers – with four input terminals each: these will be marked HF
(High Frequency) and LF (Low Frequency).
Loudspeaker cables – two pairs of cables per loudspeaker (which may
be joined at the amplifier end if your amplifier has only one pair of
output terminals per channel). Or, a suitably terminated cable set (a
loom, probably prepared by your dealer and capable of being used for
bi-wiring in one length).
How to bi-wire loudspeakers
1. Remove the terminal links on the rear of your loudspeakers
WARNING: This step is essential or damage to your amplifier
may result which is not covered under warranty.
2. Connect the cables as shown in the diagram below, ensuring
correct polarity at all times.
Recommended bi-wiring configuration Recommended bi-amping configuration
Arcam P35 power amplifier
R
Right
speaker
HF
LF
+
–
+ –
Left
speaker
L
HF
LF
+
–
+ –
SP2
SP1
SP2
SP1
R L
Arcam P35 power amplifier
+ –+ –
R
L
+ –+ –
Right
speaker
HF
LF
+
–
+
–
–
HF
LF
+
–
–
+
Left
speaker
Arcam P35 power amplifier
BI-AMPING YOUR SYSTEM
The performance of your system can be further enhanced over that
achieved with bi-wiring, by extending the principle one stage further
to include separate amplification for the low and high frequency drive
units in each loudspeaker enclosure.
Connect the integrated amplifier to the high frequency (HF) terminals
and connect the power amplifier to the low frequency (LF) terminals.
You will need:
Speakers – with four input terminals each (as with bi-wiring): these will
be marked HF (High Frequency) and LF (Low Frequency).
Four channels of amplification – for example two P35 stereo amplifiers
or four P1 monoblock amplifiers.
Loudspeaker cables – two pairs of cables per loudspeaker or a suitably
terminated cable set (a loom, probably prepared by your dealer and
capable of being used for bi-amping in one length).
Interconnect cables – one pair of high quality interconnect cables.
How to set up a bi-amped system
1. Remove the terminal links on the rear of your loudspeakers.
WARNING: This step is essential or damage to your amplifier
may result which is not covered under warranty.
2. Connect the cables as shown in the diagram below, ensuring
correct polarity at all times.
3. Use the interconnect cables to connect the PRE OUT sockets of
the C30 to the corresponding AUDIO IN sockets of the power
amplifier. If using the P1 amplifier, it may be necessary to “daisy-
chain” the interconnect cables. See page 11 for more details on
doing this.
1414
15
English
Technical specications
NOTE: All specification values are typical unless otherwise stated.
CONTINUAL IMPROVEMENT POLICY
Arcam has a policy of continual improvement for its products. This
means that designs and specifications are subject to change without
notice.
C30 P35 P1
Continuous power output (20Hz—20kHz at 0.5% THD), per channel
Both channels, 8Ω, 20Hz—20kHz 100W
Single channel, 8Ω, 20Hz—20kHz 150W 170W
Both channels, 4Ω, 20Hz—20kHz 140W
Single channel, 4Ω, at 1kHz 200W 250W
Three channels, 8Ω, 20Hz—20kHz 90W
Harmonic distortion, 80% power, 8Ω at 1kHz 0.005% 0.003%
Inputs
Phono cartridge:
Input sensitivity 2.7mV (MM); 270µV (MC)
Input impedance 47kΩ (MM); 300Ω (MC)
Signal/noise ratio (CCIR) –79dB (MM); –73dB (MC)
Overload margin 35dB
Line and tape inputs:
Nominal sensitivity 250mV—2V 800mV
Input impedance 22kΩ 22kΩ
Signal/noise ratio (CCIR) –103dB –110dB
Tone controls, max. boost/cut ±12dB @ 80Hz and 12kHz
Power amplifier input
Nominal sensitivity 800mV 906mV (Arcam gain)
Input impedance 22kΩ 22kΩ
Gain 31.5dB 31.5dB (Arcam gain)
Preamplifier output
Nominal output level 700mV
Maximum output level 8V RMS
Output impedance <50Ω
Headphone output
Maximum output level into 600Ω 5V
Output impedance 4.7Ω
General
Mains voltage 115V or 230V 115V or 230V 115V or 230V
Power consumption (maximum) 30VA 800VA (950VA for P35/3) 800VA
Power consumption (standby) 2VA 2VA 2VA
Dimensions W x D x H (including feet) 430 x 370 x 110mm 430 x 350 x 110mm 430 x 350 x 110mm
Weight (net) 9.3kg 9.5kg (10.5kg for P35/3) 12.5kg
Weight (packed) 11.5kg 12.5kg (13.5kg for P35/3) 15.5kg
Supplied accessories mains lead
CR-389 remote control
2 x AAA batteries
mains lead mains lead
E&OE
1414
15
English
Remote-control codes
The following table gives the IR-commands accepted by the C30.
Power commands
Command Decimal Code
Power toggle 16–12
Power-on 16–123
Power-off 16–124
Source selection commands
Command Decimal Code
PHONO select 16–1
AV select 16–2
TUNER select 16–3
DVD select 16–4
TAPE select 16–5
VCR select 16–6
CD select 16–7
AUX select 16–8
Volume control commands
Command Decimal Code
Mute 16–13
Volume up 16–16
Volume down 16–17
Menu navigation commands
Command Decimal Code
UP
16–32
DOWN
16–33
SELECT
16–37
ENTER
16–87
Speaker control commands
Command Decimal Code
Speaker 1 toggle 16–35
Speaker 2 toggle 16–39
Speaker 1 on 16–43
Speaker 1 off 16–44
Speaker 2 on 16–45
Speaker 2 off 16–46
Display control commands
Command Decimal Code
Display 16–59
Note that the C30 also responds to code 20–53 (the PLAY command
for an Arcam CD player). The C30 swiches automatically to CD input
on receiving this command.
1616
17
English
Service information
Before returning your amplifier for service, please check the following:
SOUND CUTS OUT FOR NO REASON
If the temperature of the internal heatsink rises above a safe level, then
a thermal cutout inside the amplifier will operate.
The power indicator on the front panel flashes and the protection
system temporarily removes the power to the speakers. The system
resets itself as the heatsink cools down.
Note that because of the high output voltage from a CD player, it is
possible to drive the P35/P1 at full power even though the C30 volume
is not set at maximum.
AMPLIFIER DOES NOT SWITCH BACK ON
The C30, P35 and P1 amplifiers have a protection mechanism which is
activated if you switch the unit on immediately after turning it off. If this
mechanism activates, wait 30 seconds then try again.
WORLDWIDE GUARANTEE
This entitles you to have the unit repaired free of charge, during the
first two years after purchase, at any authorised Arcam distributor
provided that it was originally purchased from an authorised Arcam
dealer or distributor. The manufacturer can take no responsibility for
defects arising from accident, misuse, abuse, wear and tear, neglect or
through unauthorised adjustment and/or repair, neither can they accept
responsibility for damage or loss occurring during transit to or from the
person claiming under the guarantee.
The warranty covers:
Parts and labour costs for two years from the purchase date. After two
years you must pay for both parts and labour costs. The warranty
does not cover transportation costs at any time.
CLAIMS UNDER GUARANTEE
This equipment should be packed in the original packing and returned
to the dealer from whom it was purchased, or failing this, directly to the
Arcam distributor in the country of residence. It should be sent carriage
prepaid by a reputable carrier -– NOT by post. No responsibility can
be accepted for the unit whilst in transit to the dealer or distributor
and customers are therefore advised to insure the unit against loss or
damage whilst in transit.
For further details contact Arcam at:
Arcam Customer Support Department,
Pembroke Avenue, Waterbeach, CAMBRIDGE, CB5 9QR, England
Telephone: +44 (0)1223 203200
Fax: +44 (0)1223 863384
Email: suppor[email protected]o.uk
PROBLEMS?
Always contact your dealer in the first instance.
If your dealer is unable to answer any query regarding this or any
other Arcam product please contact Arcam Customer Support on
+44 (0) 1223 203200 or write to us at the above address and we will
do our best to help you.
ON-LINE REGISTRATION
You can register your Arcam product on-line at:
www.arcam.co.uk
Guarantee
1616
17
English
NOTES
1818
19
Français
Consignes de sécurité
ATTENTION : Pour éviter tout risque de choc électrique, ne pas
enlever le couvercle (ou le panneau arrière). Aucune intervention n’est
possible pour l’utilisateur. Pour le service, voir un personnel qualifié.
AVERTISSEMENT : Pour éviter tout risque d’incendie ou de choc
électrique, ne pas exposer l’appareil à la pluie ou à l’humidité.
Le symbole d’un éclair dans un triangle a pour objet d’avertir l’utilisateur
de la présence à l’intérieur du boîtier de l’appareil de “tension électrique
dangereuse” non-isolée et de force suffisante à constituer un risque de
choc électrique.
Le point d’exclamation dans un triangle a pour objet d’avertir l’utilisateur
de la présence de renseignements importants concernant l’utilisation et
la maintenance (le service après vente) dans la documentation fournie
avec le produit.
ATTENTION : Au Canada et aux États-Unis, pour éviter tout risque de
choc électrique, alignez la lame large de la fiche secteur avec la fente
large de la prise murale, puis enfoncez la fiche complètement.
CONSEILS DE SÉCURITÉ IMPORTANTS
Cet appareil a été conçu et fabriqué conformément aux normes de
qualité et de sécurité les plus strictes. Vous devez cependant observer
les précautions suivantes lors de son installation et de son utilisation.
1. Avertissements et consignes
Il est conseillé de lire les consignes de sécurité et d’utilisation avant de
mettre cet appareil en marche. Conservez ce manuel pour pouvoir vous
y référer par la suite et respectez scrupuleusement les avertissements
figurant dans ce manuel ou sur l’appareil lui-même.
2. Eau et humidité
L’installation d’un appareil électrique à proximité d’une source d’eau
présente de sérieux risques. Il ne faut pas utiliser l’appareil à proximité
d’un point d’eau : près d’une baignoire, d’un lavabo, d’un évier, dans une
cave humide ou à côté d’une piscine, etc.
3. Chute d’objets ou infiltration de liquides
Veillez à ne pas laisser tomber d’objets ni faire couler de liquides à
travers l’une des ouvertures du boîtier. Ne posez pas d’objet contenant
du liquide sur l’appareil.
4. Ventilation
Évitez de placer l’appareil sur un lit, un canapé, un tapis ou une surface
similaire instable, ou dans une bibliothèque ou un meuble fermé, ce qui
risquerait d’empêcher une ventilation correcte. Pour permettre une
ventilation appropriée, il est conseillé de prévoir au minimum un espace
de 5 cm de chaque côté et au-dessus de l’appareil.
5. Exposition à la chaleur
Ne placez pas l’appareil près d’une flamme nue ou d’un dispositif
produisant de la chaleur, tel un radiateur, un poêle ou autre appareil (y
compris les amplificateurs).
6. Conditions climatiques
L’appareil est conçu pour fonctionner dans des climats modérés.
7. Étagères et supports
Utilisez uniquement des étagères ou des supports pour appareils
audio. Si l’appareil est posé sur un support mobile, déplacez celui-ci
avec précaution, pour éviter tout risque de chute.
8. Nettoyage
Débranchez l’appareil du secteur avant de le nettoyer.
Pour le nettoyage, utilisez un chiffon doux, humide et non pelucheux.
N’utilisez pas de diluant pour peinture ou de solvant chimique.
L’emploi d’aérosols ou de produits de nettoyage pour meubles est
déconseillé, car le passage d’un chiffon humide risquerait de laisser des
marques blanches indélébiles.
9. Alimentation secteur
Branchez l’appareil uniquement sur une alimentation secteur du type
mentionné dans le manuel d’utilisation ou indiqué sur l’appareil lui-
même.
10. Protection des cordons secteur
Veillez à ce que les cordons secteur ne se trouvent pas dans un lieu de
passage ou pincés par un objet quelconque. Prêtez particulièrement
attention aux cordons et fiches secteur à leurs points de sortie de
l’appareil.
11. Mise à la terre
Assurez-vous que l’appareil est correctement mis à la terre.
12. Câbles haute tension
Évitez de monter une antenne extérieure à proximité de câbles haute
tension.
13. Périodes de non-utilisation
Si l’appareil possède une fonction de mise en veille, un courant faible
continuera de circuler lorsqu’il est réglé sur ce mode. Débranchez
le cordon secteur de la prise murale si l’appareil doit rester inutilisé
pendant une période prolongée.
14. Odeur suspecte
Arrêtez et débranchez immédiatement l’appareil en cas de fumée ou
d’odeur anormale. Contactez immédiatement votre revendeur.
15. Service
Ne tentez pas d’effectuer d’autres opérations que celles mentionnées
dans ce manuel. Toute autre intervention doit être effectuée par un
personnel qualifié.
16. Entretien par un personnel qualifié
L’appareil doit être entretenu par du personnel qualifié lorsque :
A. la fiche ou le cordon secteur a été endommagé,
B. des objets sont tombés ou du liquide a coulé dans l’appareil,
C. l’appareil a été exposé à la pluie,
D. l’appareil ne semble pas fonctionner normalement ou présente
des altérations dans son fonctionnement,
E. l’appareil est tombé ou le boîtier a été endommagé.
CONFORMITÉ AUX NORMES DE
SÉCURITÉ
Cet appareil est conçu pour répondre à la norme internationale de
sécurité électrique IEC 60065.
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
ATTENTION
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
1818
19
Français
Utilisation de ce manuel
Merci d’avoir acheté cet appareil Arcam de qualité.
Cette notice porte sur les appareils suivants :
Préamplificateur C30
Amplificateur de puissance P35
Amplificateur de puissance P1.
Elle contient tous les renseignements dont vous avez besoin pour
installer et utiliser ces appareils. Elle décrit d’abord le C30, puis le P35
et le P1. Elle décrit aussi comment utiliser la télécommande CD-389,
qui accompagne le C30.
Si vos amplificateurs ont été installés et réglés par un concessionnaire
Arcam agréé, vous pouvez passer directement aux sections décrivant
comment utiliser cet équipement. Sinon, nous vous conseillons de lire
attentivement les directives d’installation de votre appareil avant de
commencer.
CONSIGNES DE SÉCURITÉ
Les consignes de sécurité se trouvent à la page 18 de cette notice.
Il s’agit surtout de précautions élémentaires, mais pour votre propre
sécurité, et pour ne pas endommager vos appareils, nous vous
conseillons vivement de les lire.
AUTRES LANGUES
Pour obtenir cette notice dans une autre langue, visitez notre site
Web (www.arcam.co.uk) ou adressez-vous à votre concessionnaire.
La plupart de nos manuels sont disponibles dans plusieurs langues.
TABLE DES MATIÈRES
Consignes de sécurité ................................................................18
Conseils de sécurité importants.................................................18
Conformité aux normes de sécurité........................................18
Utilisation de ce manuel.............................................................19
Installation : Préamplicateur C30...........................................20
Positionnement de l’appareil.........................................................20
Raccordement à une alimentation électrique.....................20
Branchement de l’amplicateur de puissance..................... 20
Branchement sur un autre appareil........................................... 21
Commandes du panneau avant ..................................................22
Utilisation du préamplicateur C30........................................22
Enregistrement......................................................................................23
Réglage du préamplicateur C30.............................................24
La télécommande.........................................................................25
Positionnement de l’appareil.........................................................26
Raccordement À Une Alimentation Électrique ................. 26
Installation: Amplicateurs de puissance P35 et P1..............26
Branchement sur un autre appareil........................................... 27
Branchement des haut-parleurs.................................................. 27
Mise sous tension et hors tension à distance......................27
Option trois canaux(P35 uniquement)...................................27
Utilisation de l’amplicateur de puissance.............................28
Avant de commencer .......................................................................29
Bi-câblage des haut-parleurs ......................................................... 29
Bi-câblage et bi-amplication des haut-parleurs...................29
Système à double amplication...................................................29
Spécications techniques ...........................................................30
Tableau des commandes IR .......................................................31
Garantie.........................................................................................32
Service............................................................................................32
Inscription en ligne.............................................................................. 32
2020
21
Français
POSITIONNEMENT DE L’APPAREIL
Placez l’amplificateur sur une surface plane et solide.
Évitez de le placer à la lumière directe du soleil ou près d’une source
de chaleur ou d’humidité.
Assurez une ventilation adéquate. N’installez pas l’appareil dans un
espace fermé comme une bibliothèque ou une armoire, pour ne pas
empêcher l’air d’y circuler.
RACCORDEMENT À UNE
ALIMENTATION ÉLECTRIQUE
FIL SECTEUR
L’appareil est habituellement vendu avec une prise secteur moulée déjà
installée sur le fil. Si, pour une raison quelconque, vous devez retirer
cette prise, jetez-la immédiatement, de façon sécuritaire, vu qu’elle
présente un risque de choc électrique lorsqu’elle est enfichée dans une
prise secteur. Adressez-vous à votre concessionnaire Arcam si vous
avez besoin d’un nouveau fil secteur.
PAS LA BONNE PRISE ?
Avant de la brancher, vérifiez si la prise vendue avec l’appareil
correspond à l’alimentation secteur et si la tension correspond à celle
indiquée sur le panneau arrière de l’appareil (115 V ou 230 V).
2
Si la tension ou la prise secteur est différent, adressez-vous à votre
concessionnaire Arcam.
Cet appareil doit être mis à la terre.
BRANCHEMENT
Branchez la prise (prise CEI) du cordon d’alimentation fourni avec
l’appareil dans la prise (POWER INLET)
1
qui se trouve à l’arrière de
l’appareil. Appuyez à fond.
Branchez la prise qui se trouve à l’autre extrémité du cordon dans la
prise murale et allumez-la.
ALIMENTATION STAND-BY
Pour permettre le fonctionnement en stand-by à distance, la commande
de l’amplificateur reste sous tension chaque fois que l’amplificateur est
branché sur le secteur. L’interrupteur du panneau avant éteint tous les
autres circuits. La consommation, dans ce mode, est inférieure à 2 W.
Installation : Préamplicateur C30
LR
PHONO
POWER INLET
PRE OUT
BUFFERED
L
R
L
R
L
R
VOLTAGE
SELECT
RECORD
OUT
PLAY
IN
TAPE/PROC
RECORD
OUT
PLAY
IN
VCR/TAPE 2 DVD AV TUNER CD AUX
MM
MC
REMOTE
IN
TRIG
OUT
115/230V
DIRECT
Cela signifie que même si l’interrupteur est éteint, il se peut que le
transformateur secteur qui se trouve dans l’amplificateur émette un
léger ronflement résiduel. Cela est tout à fait normal. Si vous prévoyez
ne pas utiliser cet appareil pendant un certain temps, nous vous
conseillons de le débrancher en éteignant la prise murale.
BRANCHEMENT DE L’AMPLIFICATEUR
DE PUISSANCE
PRE OUT
456
– Le branchement conseillé entre le
préamplificateur C30 et l’amplificateur de puissance dépend de
la distance entre les deux appareils et du type d’amplificateur de
puissance que vous utilisez. Il y a trois possibilités :
1. Si les fils utilisés pour relier le C30 à l’amplificateur de puissance
mesurent moins de 3 m, nous vous conseillons de brancher les
bornes DIRECT
6
aux bornes d’entrée de l’amplificateur de
puissance. Sur le P35 et le P1, branchez-les sur AUDIO IN.
Si les fils utilisés pour relier le C30 à l’amplificateur de puissance
mesurent 3 m ou plus, le branchement dépend du type de votre
amplificateur de puissance.
2. Si votre amplificateur de puissance n’a pas d’entrées symétriques
(comme le P35), utilisez les sorties isolées (BUFFERED)
5
. Sur le
P35, branchez-les sur AUDIO IN.
3. Si votre amplificateur de puissance est doté d’entrées
symétriques (comme le P1), utilisez les sorties symétriques
4
.
Sur le P1, branchez-les sur BALANCED AUDIO IN.
Les sorties isolées et symétriques sont conçues pour accepter des fils
plus longs que la sortie directe. Notez que le fait d’utiliser les sorties
isolées pour brancher le P1 n’entraîne pas de dégradation du signal et
n’endommage absolument pas l’un ou l’autre appareil.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Arcam C30, P35, P1 Manuel utilisateur
- Catégorie
- Amplificateur d'instruments de musique
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Arcam C30, P35, P1 User manual
- Deutsch: Arcam C30, P35, P1 Benutzerhandbuch
Documents connexes
-
Arcam P777 Manuel utilisateur
-
Arcam FMJ P7 Le manuel du propriétaire
-
-
Arcam FMJ A32 Manuel utilisateur
-
-
-
Arcam Stereo Amplifier MZ12 Manuel utilisateur
-
-
-
Arcam A19 Manuel utilisateur