Titan PowrLiner 4955, 6955, 8955 Manuel utilisateur

Catégorie
Pulvérisateur de peinture
Taper
Manuel utilisateur
POWRLINER
0120 • Form No. 0537859C
AIRLESS, HIGH-PRESSURE
SPRAYING UNIT
AIRLESS HOCHDRUCK-
SPRITZGERÄT
GROUPE DE PROJECTION À
HAUTE PRESSION
- GB - OPERATING MANUAL 2
- D - BETRIEBSANLEITUNG 26
- F - MODE D’EMPLOI 52
OPERATING MANUAL
Models:
PL4955 0290052
PL6955 0290053
PL8955 0290054
2 PowrLiner
GB
Warning!
Attention: Danger of injury by injection!
Airless units develop extremely high spraying pressures.
Be safety conscious!
1
2
3
Never put your ngers, hands or any other parts of the body into
the spray jet!
Never point the spray gun at yourself, other persons or animals.
Never use the spray gun without safety guard.
Do not treat a spraying injury as a harmless cut. In case of injury
to the skin through coating materials or solvents, consult a doctor
immediately for quick and expert treatment. Inform the doctor
about the coating material or solvent used.
The operating instructions state that the following points must
always be observed before starting up:
1. Faulty units must not be used.
2. Secure Titan spray gun using the safety catch on the trigger.
3. Ensure that the unit is properly earthed.
4. Check allowable operating pressure of high-pressure hose and spray
gun.
5. Check all connections for leaks.
The instructions regarding regular cleaning and maintenance of
the unit must be strictly observed.
Before any work is done on the unit or for every break in work the
following rules must be observed:
1. Release the pressure from spray gun and hose.
2. Secure the Titan spray gun using the safety catch on the trigger.
3. Switch o unit.
Original Operating Manual
PowrLiner 1
GB
Contents
Contents
Page
1. Safety regulations for Airless spraying ...................................... 2
1.1 Explanation of symbols used .............................................................. 2
1.2 Electrical safety ......................................................................................... 3
1.3 Gasoline engine safety .......................................................................... 4
1.4 Fueling (gas engine) ............................................................................... 4
2. General view of application ............................................................. 5
2.1 Application ................................................................................................ 5
2.2 Coating materials .................................................................................... 5
3. Description of unit................................................................................ 5
3.1 Airless process .......................................................................................... 5
3.2 Functioning of the unit ......................................................................... 5
3.3 System diagram - gasoline PL units .................................................. 6
3.4 Technical data for PL units ................................................................... 7
4. Operation .................................................................................................. 8
4.1 Filling the battery (PL6955 / PL8955) ............................................... 8
4.2 Setup ............................................................................................................ 8
4.3 Preparing a new sprayer ..................................................................... 10
4.4 Preparing to paint ................................................................................. 10
4.5 Painting .....................................................................................................11
4.6 Pressure relief procedure ...................................................................12
4.7 Operating the front caster .................................................................12
4.8 Folding the spray gun support bar ................................................. 12
5. Cleanup ....................................................................................................13
5.1 Special cleanup instructions for use with
ammable solvents ..............................................................................13
5.2 Cleaning the sprayer ............................................................................ 13
5.3 Cleaning a clogged tip ........................................................................13
6. Maintenance..........................................................................................14
6.1 Daily maintenance ................................................................................ 14
6.2 Maintaining the lter assembly........................................................14
6.3 Maintaining the hydraulic system ...................................................15
6.4 Maintaining the uid section ............................................................ 15
6.5 Basic engine maintenance ................................................................. 15
6.6 Replacing the motor brushes (120V electric convertokit) ......16
6.7 Adjusting the tracking of the front caster .................................... 16
6.8 Replacing the belt ................................................................................. 17
6.9 Servicing the hydraulic motor .......................................................... 18
6.10 Servicing the uid section ..................................................................20
6.11 SAE O-ring tting installation ...........................................................22
Page
7. Troubleshooting .................................................................................23
7.1 Airless gun ...............................................................................................23
7.2 Fluid section ............................................................................................ 23
7.3 Hydraulic motors ................................................................................... 24
7.4 Spray patterns ........................................................................................25
Accessories and spare parts ........................................................................78
Spare parts list for the main assembly .................................................. 78/79
Spare parts list for the cart assembly I .................................................. 80/81
Spare parts list for the cart assembly II ................................................. 82/83
Spare parts list for the hydraulic system .............................................. 84/85
Spare parts list for the hydraulic motor ............................................... 86/87
Spare parts list for the uid section • PL4955 ..................................... 88/89
Spare parts list for the uid section • PL6955 / PL8955 .................. 90/91
Spare parts list for gas convertokit ...............................................................92
Spare parts list for belt guard assembly ......................................................93
Spare parts list for the high-pressure lter ......................................... 94/95
Spare parts list for bleed hose assembly with valve ............................... 96
Spare parts list for bleed valve .......................................................................97
Spare parts list for caster assembly ...............................................................98
Spare parts list for lift / tilt assembly ............................................................99
Spare parts list for gun holder assembly ..................................................100
Hydraulic hose connection diagram .....................................................101
Connection diagram (PL4955) ..................................................................102
Connection diagram (PL6955 / PL8955) ..............................................103
Accessories for PL units ...............................................................................104
TR-1 Striping Tip Chart ....................................................................................105
Spare parts list for electric convertokit (120V) ........................................107
Warranty .............................................................................................................110
2 PowrLiner
GB
Safety precautions
1. Safety regulations for Airless spraying
1.1 Explanation of symbols used
This manual contains information that must be read and understood
before using the equipment. When you come to an area that has one
of the following symbols, pay particular attention and make certain
to heed the safeguard.
This symbol indicates a potential hazard that
may cause serious injury or loss of life. Important
safety information will follow.
At
tention
This symbol indicates a potential hazard to you
or to the equipment. Important information that
tells how to prevent damage to the equipment or
how to avoid causes of minor injuries will follow.
Danger of skin injection
Danger of fire from solvent and paint fumes
Danger of explosion from solvent, paint fumes
and incompatible materials
Danger of injury from inhalation of harmful
vapors
i
Notes give important information which should
be given special attention.
HAZARD: INJECTION INJURY
A high pressure stream produced by this equipment
can pierce the skin and underlying tissues, leading to
serious injury and possible amputation.
Do not treat a spraying injury as a harmless cut. In
case of injury to the skin through coating materials
or solvents, consult a doctor immediately for quick
and expert treatment. Inform the doctor about the
coating material or solvent used.
PREVENTION:
NEVER aim the gun at any part of the body.
NEVER allow any part of the body to touch the uid stream.
DO NOT allow body to touch a leak in the uid hose.
NEVER put your hand in front of the gun. Gloves will not
provide protection against an injection injury.
ALWAYS lock the gun trigger, shut the uid pump o and
release all pressure before servicing, cleaning the tip guard,
changing tips, or leaving unattended. Pressure will not be
released by turning o the engine. The PRIME/SPRAY valve
or pressure bleed valve must be turned to their appropriate
positions to relieve system pressure.
ALWAYS keep tip guard in place while spraying. The tip guard
provides some protection but is mainly a warning device.
ALWAYS remove the spray tip before ushing or cleaning the
system.
NEVER use a spray gun without a working trigger lock and
trigger guard in place.
All accessories must be rated at or above the maximum
operating pressure range of the sprayer. This includes spray
tips, guns, extensions, and hose.
HAZARD
: HIGH PRESSURE HOSE
The paint hose can develop leaks from wear, kinking
and abuse. A leak can inject material into the skin.
Inspect the hose before each use.
PREVENTION:
Avoid sharp bending or kinking of the high-pressure hose. The
smallest bending radius amounts to about 20 cm.
Do not drive over the high-pressure hose. Protect against
sharp objects and edges.
Replace any damaged high-pressure hose immediately.
Never repair defective high-pressure hoses yourself!
Electrostatic charging of spray guns and the high-pressure
hose is discharged through the high-pressure hose. For this
reason the electric resistance between the connections of the
high-pressure hose must be equal to or lower than 1MΩ.
For reasons of function, safety and durability use only original
Titan high-pressure hoses.
Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist. Never repair a paint hose. Replace it with
another earthed high-pressure hose.
Make sure power cord, air hose and spray hoses are routed in
such a manner to minimize slip, trip and fall hazard.
HAZARD: EXPLOSION OR FIRE
Flammable vapors, such as solvent and paint vapors,
in work area can ignite or explode.
PREVENTION:
Use equipment only in well ventilated area. Keep a good
supply of fresh air moving through the area to keep the air
within the spray area free from accumulation of ammable
vapors. Keep pump assembly in well ventilated area. Do not
spray pump assembly.
Gas models only - Do not ll fuel tank while engine is running
or hot; shut o engine and allow to cool. Fuel is ammable
and can ignite or explode if spilled on a hot surface.
Electric models only - Do not use materials with a ashpoint
below 38º C (100º F). Flashpoint is the temperature at which a
uid can produce enough vapors to ignite.
Eliminate all ignition sources, such as pilot lights, cigarettes,
portable electric lamps and plastic drop cloths (potential static
arc).
Keep work area free of debris, including solvent, rags and
gasoline.
Do not plug or unplug power cords, or turn power or light
switches on or o when ammable vapors are present.
Ground equipment and conductive objects in work area.
Make sure grounding chain is in place and reaches the
ground.
Use only grounded hoses.
Hold spray gun rmly to the side of a grounded pail when
triggering into pail.
If there is static sparking or if you feel a shock, stop operation
immediately.
PowrLiner 3
GB
Safety precautions
Know the contents of the paint and solvents being sprayed.
Read all Material Safety Data Sheets (MSDS) and container
labels provided with the paints and solvents. Follow the paint
and solvent manufacturer’s safety instructions.
Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach, mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating supplier
about compatibility of material with aluminum.
Keep a re extinguisher in work area.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, and other materials can be harmful
if inhaled or come in contact with body. Vapors can
cause severe nausea, fainting, or poisoning.
PREVENTION:
Wear respiratory protection when spraying. Read all
instructions supplied with the mask to be sure it will provide
the necessary protection.
All local regulations regarding protection against hazardous
vapors must be observed.
Wear protective eyewear.
Protective clothing, gloves and possibly skin protection cream
are necessary for the protection of the skin. Observe the
regulations of the manufacturer concerning coating materials,
solvents and cleaning agents in preparation, processing and
cleaning units.
HAZARD: GENERAL
This product can cause severe injury or property
damage.
PREVENTION:
Follow all appropriate local, state, and national codes
governing ventilation, re prevention, and operation.
Pulling the trigger causes a recoil force to the hand that is
holding the spray gun. The recoil force of the spray gun is
particularly powerful when the tip has been removed and
a high pressure has been set on the airless pump. When
cleaning without a spray tip, set the pressure control knob to
the lowest pressure.
Use only manufacturer authorized parts. User assumes all
risks and liabilities when using parts that do not meet the
minimum specications and safety devices of the pump
manufacturer.
ALWAYS follow the material manufacturer’s instructions for
safe handling of paint and solvents.
Clean up all material and solvent spills immediately to prevent
slip hazard.
Wear ear protection. This unit can produce noise levels above
85 dB(A).
Never leave this equipment unattended. Keep away from
children or anyone not familiar with the operation of airless
equipment.
Do not spray on windy days.
The device and all related liquids (i.e. hydraulic oil) must be
disposed of in an environmentally friendly way.
1.2 Electric Safety
Electric models must be grounded/earthed. In the event of an
electrical short circuit, grounding/earthing reduces the risk of electric
shock by providing an escape wire for the electric current. This
product is equipped with a cord having an grounding/earthing
wire with an appropriate earthing plug. Connection to the mains
only through a special feed point, e.g. through an error protection
insallation with INF < 30 mA.
DANGER — Work or repairs at the electrical
equipment may only be carried out by a skilled
electrician. No liability is assumed for incorrect
installation. Switch the unit o. Before all repair
work, unplug the power plug from the outlet.
Danger of short-circuits caused by water ingressing into the electrical
equipment. Never spray down the unit with high-pressure or high-
pressure steam cleaners.
Do not use 12V socket without a fully charged
battery installed.
Work or repairs at the electrical equipment:
These may only be carried out by a skilled electrician. No liability is
assumed for incorrect installation.
Operating Temperature
This equipment will operate correctly in its intended ambient, at a
minimum between +50ºF (+10°C) and 104ºF (+40°C).
Relative Humidity
The equipment will operate correctly within an environment at 50%
RH, +40°C. Higher RH may be allowed at lower temperatures.
Measures shall be taken by the Purchaser to avoid the harmful eects
of occasional condensation.
Altitude
This equipment will operate correctly up to 2100 m above mean sea
level.
Transportation and Storage
This equipment will withstand, or has been protected against,
transportation and storage temperatures of -13ºF (-25°C) to +130ºF
(+55°C) and for short periods up to 160ºF (+70°C).
It has been packaged to prevent damage from the eects of normal
humidity, vibration and shock.
4 PowrLiner
GB
Safety precautions
1.3 Gasoline Engine Safety
1. Gas engines are designed to give safe and dependable service
if operated according to instructions. Read and understand
the engine manufacturer’s Owner’s Manual before operating
the engine. Failure to do so could result in personal injury or
equipment damage.
2. To prevent re hazards and to provide adequate ventilation,
keep the engine at least 1 meter (3 feet) away from buildings
and other equipment during operation. Do not place
ammable objects close to the engine.
3. People who are not operating the device must stay away from
the area of operation due to a possibility of burns from hot
engine components or injury from any equipment the engine
may be used to operate.
4. Know how to stop the engine quickly, and understand the
operation of all controls. Never permit anyone to operate the
engine without proper instructions.
5. Gasoline is extremely ammable and is explosive under
certain conditions.
6. Refuel in a well-ventilated area with the engine stopped. Do
not smoke or allow ames or sparks in the refueling area or
where gasoline is stored.
7. Do not overll the fuel tank. After refueling, make sure the
tank cap is closed properly and securely.
8. Be careful not to spill fuel when refueling. Fuel vapor or
spilled fuel may ignite. If any fuel is spilled, make sure the area
is dry before starting the engine.
9. Never run the engine in an enclosed or conned area. Exhaust
contains poisonous carbon monoxide gas; exposure may
cause loss of consciousness and may lead to death.
10. The muer becomes very hot during operation and remains
hot for a while after stopping the engine. Be careful not to
touch the muer while it is hot. To avoid severe burns or re
hazards, let the engine cool before transporting it or storing it
indoors.
11. Never ship/transport sprayer with gasoline in the tank.
DO NOT use this equipment to spray water or acid.
Attention
Do not lift by cart handle when loading or unloading.
Device is very heavy. Three-person lift is required.
1.4 Fueling (gas engine)
Gasoline is extremely flammable and is explosive
under certain conditions.
Fuel Specications
Use automotive gasoline that has a pump octane number of
86 or higher, or that has a research octane number of 91 or
higher. Use of a lower octane gasoline can cause persistent
“pinging” or heavy “spark knock” (a metallic rapping noise)
which, if severe, can lead to engine damage.
i
If “spark knock” or “pinging” occurs at a steady
engine speed under normal load, change brands of
gasoline. If spark knock or pinging persists, consult
an authorized dealer of the engine manufacturer.
Failure to do so is considered misuse, and damage
caused by misuse is not covered by the engine
manufacturer’s limited warranty.
Occasionally you may experience light spark knock
while operating under heavy loads. This is no
cause for concern, it simply means your engine is
operating eciently.
Unleaded fuel produces fewer engine and spark plug deposits
and extends the life of the exhaust system components.
Never use stale or contaminated gasoline or an oil/gasoline
mixture. Avoid getting dirt, dust, or water in the fuel tank.
Gasolines Containing Alcohol
If you decide to use a gasoline containing alcohol (gasohol), be
sure its octane rating is at least as high as that recommended by
the engine manufacturer. There are two types of “gasohol”: one
containing ethanol, and the other containing methanol. Do not use
gasohol that contains more than 10% ethanol. Do not use gasoline
containing methanol (methyl or wood alcohol) that does not also
contain co-solvents and corrosion inhibitors for methanol. Never
use gasoline containing more than 5% methanol, even if it has co-
solvents and corrosion inhibitors.
i
Fuel system damage or engine performance
problems resulting from the use of fuels that contain
alcohol is not covered under the warranty. The
engine manufacturer cannot endorse the use of
fuels containing methanol since evidence of their
suitability is incomplete at this time.
Before buying gasoline from an unfamiliar station, try
to nd out if the gasoline contains alcohol. If it does,
conrm the type and percentage of alcohol used. If
you notice any undesirable operating characteristics
while using a gasoline that contains alcohol, or one
that you think contains alcohol, switch to a gasoline
that you know does not contain alcohol.
PowrLiner 5
GB
General view of application Description of unit
2. General view of application
2.1 Application
This airless line striper is a precision power tool used to spray many
types of material for many types of applications including parking
lots, curbs, and athletic elds. Read and follow this instruction manual
carefully for proper operating instructions, maintenance, and safety
information.
2.2 Coating materials
Processible coating materials
i
Pay attention to the Airless quality of the coating
materials to be processed.
Latex paint, dispersion paints, re protection and thick lm materials,
zinc dust and micaceous iron ore paints, Airless spray primer,
sprayable glue, anti-corrosive agents, thick coating materials and
bitumen-like coating materials.
No other materials should be used for spraying without Titan’s
approval.
Filtering
In spite of the high-pressure lter, ltering of the coating material is
recommended in general.
Mix coating material before commencement of work.
i
Make sure when stirring with motor-driven agitators
that no air bubbles are stirred in. Air bubbles disturb
when spraying and can, in fact, lead to interruption
of operation.
Viscosity
It is possible to work with high-viscosity coating materials with the
devices.
If highly viscous coating materials cannot be sucked up, they must be
diluted in accordance with the manufacturer’s instruction.
Two-component coating material
The appropriate processing time must be adhered to exactly. A
minimum of 45 minute set time is recommended. Within this time
rinse through and clean the unit meticulously with the appropriate
cleaning agents.
Coating materials with sharp-edged additional materials
These have a strong wear and tear eect on valves, high-pressure
hose, spray gun and tip. The durability of these parts can be reduced
appreciably through this.
3. Description of unit
3.1 Airless process
The main area of application are thick layers of highly viscous coating
material for large areas and a high consumption of material.
A piston pump takes in the coating material by suction and conveys it
to the tip. Pressed through the tip at a pressure of up to a maximum
of 227 bar (22.7 MPa, 3300 PSI), the coating material is atomized. This
high pressure has the eect of micro ne atomisation of the coating
material.
As no air is used in this process, it is described as an AIRLESS process.
This method of spraying has the advantages of nest atomisation,
cloudless operation and a smooth, bubble-free surface. As well as
these, the advantages of the speed of work and convenience must be
mentioned.
3.2 Functioning of the unit
The following section contains a brief description of the technical
construction for better understanding of the function.
TITAN PowrLiner (PL) are high-pressure spraying units driven by
either a gasoline engine or electric motor.
The gasoline engine or electric motor (g. 1, item 1) drives the
hydraulic pump (3) by means of a V-belt which is under the belt cover
(2). Hydraulic oil ows to the hydraulic motor (4) and then moves the
piston up and down in the material feed pump (5).
The inlet valve is opened automatically by the upwards movement
of the piston. The outlet valve is opened when the piston moves
downward.
The coating material ows under high pressure through the high-
pressure hose to the spray gun. When the coating material exits from
the tip it atomizes.
The pressure control valve (6) controls the volume and the operating
pressure of the coating material.
4
5
6
1
3
2
6 PowrLiner
GB
Description of unit
3.3 System diagram - gasoline PL units
1 Adjustable handle (2)
2 Hydraulic motor
3 Oil cup for Piston Lube (Piston Lube prevents increased wear
and tear of the packings)
4 Pressure control knob
5 High-pressure lter
6 High-pressure hose outlet (rst gun)
7 Relief valve handle: Turn left for circulation k
Turn right for spray p
8 High-pressure hose outlet (second gun)
9 V-belt under the belt cover
10 Ball valve: horizontal position – hydraulic motor switched o
vertical position – hydraulic motor switched on
11 Bleed hose
12 Suction tube
13 Oil measuring stick
14 Gasoline engine
15 PowrCenter™
16 SmartArm™
7
6
8
11
4
2
10
15
12
13
14
9
16
3
5
1
8
7
10
3
6
PowrLiner 7
GB
Description of unit
PL4955 PL6955 PL8955
Gasoline engine, power
118cc, 3.5 Hp 163cc, 4.8 Hp (electric start) 196cc, 5.5 Hp (electric start)
Fuel Capacity
0.53 US gal (2.0 l) 0.83 US gal (3.1 l) 0.83 US gal (3.1 l)
Max. operating pressure
22.7 MPa (227 bar, 3300 PSI) 22.7 MPa (227 bar, 3300 PSI) 22.7 MPa (227 bar, 3300 PSI)
Max. sound pressure level
92 dB (A)* 92 dB (A)* 98 dB (A)*
Max. size of tip with a spray gun
1-gun 0.034” – 0.86 mm 0.050” – 1.27 mm 0.054” – 1.37 mm
2-gun 0.024” – 0.61 mm 0.033” – 0.84 mm 0.038” – 0.96 mm
Max. volume ow
1.25 gal (4.7 l)/min 2.25 gal (8.5 l)/min 2.5 gal (9.5 l)/min
Weight
324 lbs (147 kg) 334 lbs (151 kg) 339 lbs (154 kg)
Max. viscosity
50.000 mPa·s 50.000 mPa·s 65.000 mPa·s
Dimensions L x W x H
72” x 42” x 42”
(183 cm x 107 cm x 107 cm)
72” x 42” x 42”
(183 cm x 107 cm x 107 cm)
72” x 42” x 44”
(183 cm x 107 cm x 112 cm)
Max. temperature of the coating material
109ºF (43° C) 109ºF (43° C) 109ºF (43° C)
Filter insert (standard equipment)
50 mesh, 18 in
2
50 mesh, 18 in
2
50 mesh, 18 in
2
Hydraulic oil lling quantity
5.9 l (1.56 gal) CoolFlo 5.9 l (1.56 gal) CoolFlo 5.9 l (1.56 gal) CoolFlo
Max. tire pressure
0.2 MPa (2 bar, 30 PSI) 0.2 MPa (2 bar, 30 PSI) 0.2 MPa (2 bar, 30 PSI)
Special high-pressure hose
DN 6 mm, 15 m (50’ x 1/4”),
connection thread NPSM 1/4
DN 6 mm, 15 m (50’ x 1/4”),
connection thread NPSM 1/4
DN 6 mm, 15 m (50’ x 1/4”),
connection thread NPSM 1/4
* Place of measurement: 1 m distance from unit and 1.60 m above reverberant oor, 120 bar (12 MPa) operating pressure.
3.4 Technical data for PL units
8 PowrLiner
GB
Operation
4.2 Setup
1. Make sure the siphon hose (g. 3, item 1) is connected to the
uid section (2) and the bleed hose (3) is connected to the
bleed valve (4).
1
2
3
4
2. Install the gun support bar.
i
The spray gun, hose, and cables are mounted to the
gun support bar at the factory.
a. Loosen the tilt clamp knob (g. 4, item 1) and lower the gun
support bar into position.
b. Loosen the support bar clamps (2) on each side of the cart.
c. Slide the gun support bar (3) through the cart.
d. Tighten the support bar clamps (2) to secure the gun support
bar in position.
i
The support bar height will need to be lower than
the cart frame to allow it to slide through the cart.
3
1
2
i
The gun support bar and the spray gun(s) can be
mounted on either side of the sprayer.
3. Position the rst spray gun.
a. Disengage the trigger cable from the tensioning clamp.
4. Operation
This equipment produces a fluid stream at extremely
high pressure. Read and understand the warnings
in the Safety Precautions section at the front of this
manual before operating this equipment.
4.1 Filling the Battery (PL6955 / PL8955)
Due to shipping regulations, the battery in your PowrLiner has been
shipped to you empty. Before using the PowrLiner, the battery
must be lled with electrolyte (acid) and then charged. Follow the
instructions below.
i
Battery electrolyte can be purchased at your local
hardware or auto parts retailer.
Battery electrolyte is very hazardous. Make sure
to follow all precautions and warnings on the
electrolyte container.
Electrolyte specications
In cool or temperate climates, purchase electrolyte with a specic
gravity of 1.270 - 1.280.
In tropical climantes, purchase electrolyte with a specic gravity of
1.250 - 1.260.
Fill the battery
1. Remove the battery from the cart.
a. Remove the 12 gallon hopper from the cart.
b. Unscrew and remove the four (4) screws and washers that
secure the hopper plate to the cart. The top of the battery
should now be exposed.
2. Remove rubber sealing cap from the exhaust opening on the
side of the battery.
3. Replace the rubber sealing cap with the exhaust tube
provided (this can be found in the plastic bag containing the
instruction manual and other literature).
4. Remove the six (6) yellow lling caps on top of the battery.
5. Fill the battery with electrolyte in each of the lling ports (see
“Electrolyte specications”, above). Fill the battery to the
upper level as indicated on the battery case.
Attention
The electrolyte temperature must not be lower than
60º F (15º C) or higher than 86º F (30º C).
6. Allow the battery to stand for at least 30 minutes after lling.
7. After 30 minutes, check electrolyte level. If the level has fallen,
rell to the upper level prior to charging.
8. Replace the yellow lling caps.
9. Replace the hopper plate back onto the cart and secure using
the four (4) screws and washers.
Charge the battery
1. Place the battery on a charge for 3 to 5 hours at the
approximate current equivalent to 1/10th of its rated capacity.
a. If electrolyte level falls after charging, ll with distilled water to
upper level.
b. After water is added, continue charging for 1 to 2 hours in
order to mix the water with the electrolyte.
2. After charging, check the battery voltage three times at 30
minute intervals. Make sure the voltage is constant over the
three readings.
3. Replace the ller plugs (if needed) and wash o any
electrolyte spillage with clean water.
PowrLiner 9
GB
Operation
Attention
Always disengage the trigger cable from the
tensioning clamp before making any adjustments to
the spray gun position.
b. Loosen the support bar clamps and slide the gun support bar
to the desired horizontal position.
c. Loosen the gun riser clamp and slide the spray gun to the
desired vertical position.
i
The height of the spray gun aects the width of the
spray pattern (i.e., the lower the gun, the smaller the
line width). Tip size also aects line width.
4. Repeat steps 3a through 3c for the second spray gun.
i
It is recommended that both spray guns be installed
at the same height as a starting point. The gun
heights can be adjusted individually based on
spraying needs (i.e. spraying a curb or spraying two
lines of dierent widths).
5. Once both guns are installed, their vertical position can be
adjusted simultaneously.
a. Loosen the vertical support clamp knob (g. 5, item 1) on the
riser.
b. Turn the crank (2) to adjust the overall height of the spray guns.
c. Once at desired height, re-tighten the vertical support clamp
knob (1).
1
2
6. Set the trigger selector for proper spray gun operation (g.
6). The right handlebar triggers the gun or guns. The selector
on the trigger must be set for the rst gun, both guns, or the
second gun .
Attention
Always turn the trigger lock on the spray gun to the
locked position before making any adjustments to
the trigger selector. Also, release the trigger cable
from its block by lifting the cable up and out of the
block. There will be a brief triggering of the gun
while releasing the trigger cable.
i
If lift/tilt assembly has excessive friction during
operation, spray the tubes with dry graphite
lubricant.
a. First Gun — The rst gun position is with the selector in the
left position. Push the lever toward the inside of the frame until
the pin engages the left plate.
b. Both Guns — The dual gun position is with the selector in the
center position. Push the lever toward the center position until
the pin engages both plates. The pin must engage both plates.
c. Second Gun — The second gun position is with the selector in
the right position. Push the lever away from the inside of the
frame until the pin engages the right plate.
ABC
7. Fill the oil cup 1/2 full with Piston Lube (P/N 314-480). This
extends packing life.
Attention
Piston Lube prevents increased wear and tear to the
packings.
8. Check the hydraulic uid level daily before starting the
sprayer. The hydraulic uid level should be at the “Full” mark
on the dipstick. Refer to the Maintenance section of this
manual for hydraulic system maintenance instructions.
Attention
Use of Titan’s Coolflo™ Hydraulic Fluid (P/N 430-361)
is mandatory in the hydraulic system. Do not use
any other hydraulic fluid. Use of any other hydraulic
fluid may seriously damage the hydraulic system
and will void the warranty.
9. For gas models, check the engine oil level daily before starting
the sprayer. The gasoline engine oil level is determined by
the engine manufacturer. Refer to the engine manufacturer’s
service manual supplied with this sprayer.
10. For electric models, use a 20 amp service outlet. Always locate
the electric model within 10 to 15 feet of the service outlet. Use
a short electric cable and a long paint hose. Any extension cord
will create some voltage drop. If an extension cord is necessary,
use only a grounded 3-wire #12 extension cord.
Electric models only - Do not use materials with a
ashpoint below 38º C (100º F). Flashpoint is the
temperature at which a uid can produce enough
vapors to ignite.
11. Make sure the sprayer is grounded/earthed. All sprayers are
equipped with an grounding/earthing chain. Make sure
the chain reaches all the way to the ground. Check your
local electrical regulations for detailed grounding/earthing
instructions.
Proper grounding/earthing is important. This applies to
both gas and electric powered models. The passage of
some materials through the nylon uid hose will build
up a static electric charge, which if discharged, could
ignite solvent vapors present and create an explosion.
12. Strain all paints with a nylon strainer to ensure trouble free
operation and freedom from frequent cleaning of the inlet
screen and gun lter.
13. Make sure the spray area is well ventilated to prevent
hazardous operation with volatile solvents or exhaust fumes.
10 PowrLiner
GB
Operation
turn the engine switch to the OFF position.
b. To turn o the electric motor,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the ON/OFF switch to the OFF position.
4.4 Preparing to Paint
Before painting, it is important to make sure that the uid in the
system is compatible with the paint that is going to be used.
i
Incompatible uids and paint may cause the valves
to become stuck closed, which would require
disassembly and cleaning of the sprayer’s uid
section.
Attention
Always keep the trigger lock on the spray gun in the
locked position while preparing the system.
1. Place the siphon tube into a container of the appropriate
solvent for the material being sprayed.
i
If you are spraying a water-based latex, ush with
warm, clean water. If you are using any other
material, check with the material manufacturer for a
compatible solvent.
2. Place the bleed hose into a metal waste container.
3. Turn the pressure control knob fully counterclockwise to its
lowest pressure setting (g 8, 1).
4. Open the hydraulic shut-o valve (2) located on the hydraulic
pressure hose. The handle should be in line with the hose.
5. Open the bleed valve (3) by turning it fully counterclockwise.
6. Start the engine or turn on the electric motor.
a. To start the gas engine (g. 9),
move the fuel valve lever (2) to the open position,
move the throttle lever (3) to its middle point,
move the choke lever (4) to the closed position for a cold
engine or to the open position for a warm engine,
turn the engine switch (1) to the ON position, and
pull the starter rope (5) briskly until the engine starts or turn
and hold the electric starter key towards “Start” until the engine
starts (PL6955/PL8955 only)
b. To start the electric motor, move the ON/OFF switch to the ON
position.
7. Turn the pressure control knob (1) clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent ows freely from the bleed hose.
8. Allow the sprayer to run for 15–30 seconds to ush the test
uid out through the bleed hose and into the waste container.
9. Turn o the sprayer.
a. To turn o the gas engine,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the throttle lever to the slow position, and
turn the engine switch to the OFF position.
b. To turn o the electric motor,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the ON/OFF switch to the OFF position.
i
Make sure that the spray gun does not have a tip or
tip guard installed.
10. Close the bleed valve by turning it fully clockwise.
11. Start the engine or turn on the electric motor.
4.3 Preparing a New Sprayer
If this unit is new, it is shipped with test uid in the uid section to
prevent corrosion during shipment and storage. This uid must be
thoroughly cleaned out of the system with mineral spirits before you
begin spraying.
Attention
Always keep the trigger lock on the spray gun in the
locked position while preparing the system.
1. Place the siphon tube into a container of mineral spirits.
2. Place the bleed hose into a metal waste container.
3. Turn the pressure control knob fully counterclockwise to its
lowest pressure setting (g 8, 1).
4. Open the hydraulic shut-o valve (2) located on the hydraulic
pressure hose. The handle should be in line with the hose.
5. Open the bleed valve (3) by turning it fully counterclockwise.
1
2
3
6. Start the engine or turn on the electric motor.
a. To start the gas engine (g. 9),
move the fuel valve lever (2) to the open position,
move the throttle lever (3) to its middle point,
move the choke lever (4) to the closed position for a cold
engine or to the open position for a warm engine,
turn the engine switch (1) to the ON position, and
pull the starter rope (5) briskly until the engine starts or turn
and hold the electric starter key towards “Start” until the engine
starts (PL6955/PL8955 only)
b. To start the electric motor, move the ON/OFF switch to the ON
position.
5
2
3
4
1
7. Turn the pressure control knob (g. 8, 1) clockwise
approximately 1/3 of the way down to increase pressure until
the sprayer cycles evenly and solvent ows freely from the
bleed hose.
8. Allow the sprayer to run for 15–30 seconds to ush the test
uid out through the bleed hose and into the waste container.
9. Turn o the sprayer.
a. To turn o the gas engine,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the throttle lever to the slow position, and
PowrLiner 11
GB
Operation
7. Turn the pressure control knob (1) clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent ows freely from the bleed hose.
8. Turn o the sprayer.
a. To turn o the gas engine,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the throttle lever to the slow position, and
turn the engine switch to the OFF position.
b. To turn o the electric motor,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the ON/OFF switch to the OFF position.
9. Remove the bleed hose from the waste container and place it
into the container of paint.
10. Close the bleed valve by turning it fully clockwise.
11. Start the engine or turn on the electric motor.
12. Turn the pressure control knob clockwise approximately 1/3
of the way down to increase pressure.
13. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Earth the gun by holding it against the edge of the
metal container while flushing. Failure to do so may
lead to a static electric discharge, which may cause
a fire.
14. Trigger the gun into the metal waste container until all air and
solvent is ushed from the spray hose and paint is owing
freely from the gun.
15. Lock the gun by turning the gun trigger lock to the locked
position (g 11).
16. Turn o the sprayer.
17. Attach tip guard and tip to the gun as instructed by the tip
guard or tip manuals.
POSSIBLE INJECTION HAZARD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the unclog
position. Always engage the gun trigger lock before
removing, replacing or cleaning tip.
18. Start the engine or turn on the electric motor.
19. Increase the pressure by turning the pressure control knob
slowly clockwise and test the spray pattern on a piece of
cardboard. Adjust the pressure control knob until the spray
from the gun is completely atomized.
i
Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear and
additional overspray.
12. Turn the pressure control knob clockwise approximately 1/3
of the way down to increase pressure.
13. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Earth the gun by holding it against the edge of the
metal container while flushing. Failure to do so may
lead to a static electric discharge, which may cause
a fire.
14. Trigger the gun into the metal waste container until the old
solvent is gone and fresh solvent is coming out of the gun.
15. Lock the gun by turning the gun trigger lock to the locked
position (g 11).
16. Set down the gun and increase the pressure by turning the
pressure control knob slowly clockwise to its highest setting.
17. Check the entire system for leaks. If leaks occur, turn the
sprayer o and follow the “Pressure Relief Procedure” in this
manual before tightening any ttings or hoses.
18. Follow the “Pressure Relief Procedure” (section 4.6) in this
manual before changing from solvent to paint.
Be sure to follow the Pressure Relief Procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for
cleanup.
4.5 Painting
1. Place the siphon hose into a container of paint.
2. Place the bleed hose into a metal waste container.
3. Turn the pressure control knob fully counterclockwise to its
lowest pressure setting (g 8, 1).
4. Open the hydraulic shut-o valve (2) located on the hydraulic
pressure hose. The handle should be in line with the hose.
5. Open the bleed valve (3) by turning it fully counterclockwise.
6. Start the engine or turn on the electric motor.
a. To start the gas engine (g. 9),
move the fuel valve lever (2) to the open position,
move the throttle lever (3) to its middle point,
move the choke lever (4) to the closed position for a cold
engine or to the open position for a warm engine,
turn the engine switch (1) to the ON position, and
pull the starter rope (5) briskly until the engine starts or turn
and hold the electric starter key towards “Start” until the engine
starts (PL6955/PL8955 only)
b. To start the electric motor, move the ON/OFF switch to the ON
position.
4.8 Folding the Spray Gun Support Bar
The spray gun support bar can be lifted vertically in order to make
the sprayer smaller for storage. The spray guns or spray hoses do not
need to be removed. Follow the steps below.
1. Loosen the support bar clamps (g. 12, 1). Pull the support
bar (2), with gun holder assemblies and spray guns still
attached, away from the cart as far as it will go without being
completely removed.
i
The support bar needs to remain completely within
the tilt sleeve (3) so that both support bar clamps
can re-engage.
2. Tighten the support bar clamps (1). Both clamps need to be
engaged into the support bar (2).
3. Loosen the spray gun holder clamps (4) and slide both spray
guns as far to the end of the support bar as they can go.
4. Loosen the vertical support clamp knob (5) on the riser. Turn
the crank (6) so that the entire support bar assembly is raised
as far as it will go. Tighten the vertical support clamp knob (5).
2
4
6
5
7
3
1
5. Loosen the tilt knob (7). Carefully raise the support bar to a
vertical position.
Attention
Pinch hazard. Make sure keep ngers away from
all moving parts. Make sure no hoses or cables get
pinched in any moving parts.
6. Tighten the tilt knob (7) to secure in place.
4.6 Pressure Relief Procedure
Be sure to follow the Pressure Relief Procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray nozzles, or preparing for
cleanup.
1. Lock the spray gun by turning the gun trigger lock to the
locked position.
2. Turn o the sprayer.
a. To turn o the gas engine,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the throttle lever to the slow position, and
turn the engine switch to the OFF position.
b. To turn o the electric motor,
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
move the ON/OFF switch to the OFF position.
3. Close the hydraulic shut-o valve on the hydraulic pressure
hose.
4. Unlock the gun by turning the gun trigger lock to the
unlocked position.
5. Hold the metal part of the gun rmly to the side of a metal
waste container to earth the gun and avoid a build up of static
electricity.
6. Trigger the gun to remove any pressure that may still be in the
hose.
7. Lock the gun by turning the gun trigger lock to the locked
position.
8. Place the bleed hose into the metal waste container.
9. Open the bleed valve by turning it fully counterclockwise.
4.7 Operating the Front Caster
The front caster on the cart is designed to track the sprayer in either
a straight line or allow free motion. Standing behind the sprayer, the
trigger on the left handle of the cart controls the operation of the
front caster.
1. To lock the front caster in the straight line position, squeeze
then release the caster trigger and move the sprayer forward.
2. To allow free motion of the front caster, squeeze and hold the
caster trigger.
12 PowrLiner
GB
Operation
5. Cleanup
Attention
The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits
material to build up, seriously aecting the
performance of the unit.
Always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a re or
explosion in the presence of ammable vapors.
5.1 Special cleanup instructions for use with
ammable solvents
Always ush spray gun preferably outside and at least one
hose length from spray pump.
If collecting ushed solvents in a one gallon metal container,
place it into an empty ve gallon container, then ush
solvents.
Area must be free of ammable vapors.
Follow all cleanup instructions.
5.2 Cleaning the Sprayer
1. Follow the “Pressure Relief Procedure” found in the Operation
section of this manual, section 4.6.
2. Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
3. Place the siphon tube into a container of the appropriate
solvent.
Attention
Use only compatible solvents when cleaning
out oil based enamels, lacquers, coal tar, and
epoxies. Check with the uid manufacturer for the
recommended solvent.
4. Place the bleed hose into a metal waste container.
5. Set the pressure to minimum by turning the pressure control
knob (1) fully counterclockwise.
6. Open the hydraulic shut-o valve located on the hydraulic
pressure hose (2). The handle should be in line with the hose.
7. Open the bleed valve (3) by rotating the bleed valve handle
fully counterclockwise.
1
2
3
8. Start the engine or turn on the electric motor.
9. Allow the solvent to circulate through the sprayer and
ush the paint out of the bleed hose into the metal waste
container.
10. Turn o the sprayer.
PowrLiner 13
GB
Cleanup
11. Close the bleed valve by rotating the bleed valve handle fully
clockwise.
12. Start the engine or turn on the electric motor.
Earth the gun by holding it against the edge of the
metal container while flushing. Failure to do so may
lead to a static electric discharge, which may cause
a fire.
13. Trigger the gun into the metal waste container until the paint
is ushed out of the hose and solvent is coming out of the
gun.
14. Continue to trigger the spray gun into the waste container
until the solvent coming out of the gun is clean.
i
For long-term or cold weather storage, pump
mineral sprits through the entire system.
15. Follow the “Pressure Relief Procedure” found in the Operation
section of this manual.
16. Store the sprayer in a clean, dry area.
Attention
Do not store the sprayer under pressure.
5.3 Cleaning a Clogged Tip
1. Follow the “Pressure Relief Procedure” in the Operation
section of this manual.
2. If the tip clogs, rotate the tip handle 180° until the arrow on
the handle is facing the opposite of the spray direction and
the handle clicks in the reverse position.
3. Trigger the gun once so that the pressure can blow the clog
out. NEVER use the tip in the reverse position for more than
ONE trigger pull at a time. This procedure can be repeated
until the tip is free of clogging.
The ow from the spray tip is at very high pressure.
Contact with any body part may be dangerous. Do
not place nger on gun outlet. Do not point the gun
at any person. Never operate the spray gun without
the proper tip guard.
14 PowrLiner
GB
Maintenance
6. Maintenance
Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
Additionally, follow all other warnings to reduce the
risk of an injection injury, injury from moving parts
or electric shock. Always unplug the sprayer before
servicing!
6.1 Daily Maintenance
Two daily procedures are required for routine operator maintenance
on this sprayer:
A. Lubricating the upper packings.
B. Cleaning the lter screen
A) Lubricating the Upper Packings
1. Clean out the paint that has seeped past the upper packings
into the packing oil reservoir (g. 15, item 1) above the uid
section.
2. Fill the packing oil reservoir 1/2 full with Piston Lube (P/N 314-
480) supplied by the factory. This will extend packing life.
1
i
Do not over-ll the reservoir so that it overows and
drips into the paint.
B) Cleaning the Filter Screen
1. The lter screen will clog and must be cleaned at least once a
day.
2. Loosen the hex nut (g. 16, item 1) that secures the lter
screen to the siphon tube.
3. Remove the lter screen (2) from the bottom of the siphon
tube.
4. Clean thoroughly with the appropriate solvent.
2
1
6.2 Maintaining the Filter Assembly
Clean the lter regularly. Dirty or clogged lters can greatly reduce
ltering ability and cause a number of system problems including
poor spray patterns, clogged spray tips, etc.
Cleaning (Fig. 17)
To clean the lter, perform the following procedure.
1. Follow the “Pressure Relief Procedure” found in the Operation
section of this manual.
2. Remove the lter cap assembly (1) and spring (2).
3. Pull the lter element with ball straight (3) out of the lter
body (4).
4. Clean inside the lter body, lter element with ball, and lter
cap assembly using the appropriate solvent.
i
Use care in handling parts as dirt, debris, scratches,
or nicks may prevent o-rings or gaskets from sealing.
This lter element lters from the inside out. Be sure
to clean the lter element thoroughly on the inside.
Soak in solvent to loosen hardened paint or replace.
1
3
5
4
7
8
6
2
Inspection (Fig. 17)
Inspect all parts of the lter assembly before reassembly.
1. Inspect the ball inside the lter element. If the ball has
pressure cuts or scratches, replace the lter element.
a. If the ball is cut, remove the PTFE o-ring (5) using an o-ring pick
and remove the carbide seat (6).
b. Check the seat for nicks or grooves. If the seat is damaged,
replace.
i
Removal of the PTFE o-ring will damage the o-ring
and require replacement.
2. Remove the spring (2) from the spring guide on the lter cap.
a. Measure the length of the spring uncompressed. If it measures
less than 3/4” from end to end, replace.
b. Push the spring back onto the spring guide until it “snaps” back
into position.
3. Inspect the two PTFE gaskets (7,8) and the PTFE o-ring (5) for
deformity, nicks, or cuts. Replace, if needed.
i
The PTFE gaskets, PTFE o-ring, and spring are
packaged in Filter Service Kit P/N 930-050.
PowrLiner 15
GB
Maintenance
Reassembly (Fig. 17)
After cleaning and inspecting all parts, reassemble the lter.
1. Place the carbide seat (6) into the lter body (4). Make sure
the beveled side of the seat is facing up.
2. Place the PTFE o-ring (5) into the groove on the outer
diameter of the carbide seat (6).
3. Place the lter element with ball (3) into the lter body (4).
i
The top and bottom of the lter element with ball
are identical.
4. Push the spring (2) back onto the spring guide of the lter cap
(1) until it “snaps” back into position, if not already done.
5. Place the thin PTFE gasket (8) onto the step at the top of the
lter body (4).
6. Place the thick PTFE gasket (7) onto the top of the thin gasket
(8).
7. Tighten the lter cap assembly (1) onto the lter body (4).
6.3 Maintaining the Hydraulic System
Attention
Use of Titan’s Coolflo™ Hydraulic Fluid is mandatory
in the PowrLiner hydraulic system. Do not use any
other hydraulic fluid. Use of any other hydraulic
fluid may seriously damage the hydraulic system
and will void the warranty.
1. Check the hydraulic uid daily. It should be at the “Full”
mark (g. 18, item 1) on the dipstick (2). If it is low, add only
Titan Coolo™ Hydraulic Fluid (P/N 430-361). Never add
or change hydraulic uid except in a clean, dust-free area.
Contamination of the hydraulic uid will shorten hydraulic
pump life and may void warranty.
3
1
2
2. Change the hydraulic uid every twelve months. Drain the
old uid from the tank and ll with 6.25 quarts of hydraulic
uid. Start the sprayer at just enough pressure to operate the
uid section. Run the sprayer at this low pressure for at least
5 minutes. This removes air from the system. Check the uid
level after this procedure. Do not over-ll.
i
When replacing the hydraulic filter (3) during a
fluid change, it may be necessary to add up to one
additional quart of hydraulic fluid.
3. The hydraulic system has an external, replaceable hydraulic
lter. Change the lter every twelve months.
4. The hydraulic pump should not be serviced in the eld. If
service on the hydraulic pump is required, it must be returned
to Titan.
6.4 Maintaining the Fluid Section
If the sprayer is going to be out of service for an extended period of
time, it is recommended that following cleanup, a kerosene and oil
mixture be introduced as a preservative. Packings may tend to dry
out from lack of use. This is particularly true of the upper packing
set for which upper packing lubricant Piston Lube (P/N 314-480) is
recommended in normal usage.
If the sprayer has been out of service for an extended period of time,
it may be necessary to prime the pump with solvent. It is extremely
important that the threads on the siphon hose coupling are properly
sealed. Any air leakage will produce erratic operation of the sprayer
and may damage the system. The up and the down strokes should
be approximately equal in time (one should not be faster than the
other). A fast up or down stroke may indicate air in the system or
malfunctioning valve or seats (see the Troubleshooting section).
6.5 Basic Engine Maintenance (gas engine)
For detailed engine maintenance and technical specications
refer to the separate gasoline engine manual.
All service to the engine should be performed by a dealer
authorized by the engine manufacturer.
Use a premium quality motor oil. 10W30 is recommended for
general all temperature use. Other viscosities may be required
in other climates.
Use only a (NGK) BP6ES / BPR6E spark plug. Gap the plug
to 0.028 to 0.031 In. (0.7 to 0.8 mm) Always use a spark plug
wrench.
Daily
1. Check engine oil level, and ll as necessary.
2. Check gasoline level, and ll as necessary.
Always follow the fueling procedure outlined earlier
in this manual.
First 20 Hours
1. Change engine oil.
Every 100 Hours
1. Change engine oil.
2. Clean the sediment cup.
3. Clean and re-gap the spark plug.
4. Clean the spark arrestor.
Weekly
1. Remove the air lter cover and clean the element. In very
dusty environments, check the lter daily. Replace the
element as needed. Replacement elements can be purchased
from your local engine manufacturer dealer.
Engine Operation and Service
1. Clean and oil air lter pad on gasoline engine every 25 hours
or once weekly. Do not permit the air intake screen around
the y wheel of the gas engine to load up with paint or
trash. Clean it regularly. The service life and eciency of
the gas engine model depends upon keeping the gasoline
engine running properly. Change the oil in the engine
every 100 hours. Failure to observe this may result in engine
overheating. Consult the engine manufacturer’s service
manual provided.
2. To conserve fuel, service life, and eciency of the sprayer,
always operate the gasoline engine at the lowest RPM at
which it runs smoothly without laboring and delivers the
amount required for the particular painting operation.
Higher RPM does not produce higher working pressure. The
gasoline engine is connected to the hydraulic pump by a
pulley combination designed to produce full paint delivery at
maximum RPM.
3. The warranty on gasoline engines or electric motors is limited
to the original manufacturer.
16 PowrLiner
GB
Maintenance
6.6 Replacing the Motor Brushes (optional 120V
electric motor, PL4955 only)
The 120V electric Convertokit is available for separate purchase.
When installing the 120V Convertokit, strap down
the front of the PowrLiner to prevent it from tipping
backwards.
Perform this procedure using Motor Brush Kit P/N 978-050. The kit
consists of two brushes, two springs, and two clips.
i
Brushes should be replaced when they are worn to
less than 1/2 inch. Check and replace both brushes
at the same time.
1. Remove both inspection covers (1) on the motor.
1
2. Push in the spring clip (2) to unhook it, then pull it out.
3. Loosen the terminal screw (3). Pull the brush lead (4) away,
but leave the motor lead in place. Remove the brush and
spring.
3
2
4
4. Inspect the commutator (5) for burning, excessive pitting or
gouging. A black color on the commutator is normal.
5
5. Install the new brush (6) so its lead slides in the long slot of the
brush holder (7). Push the terminal under the terminal screw
washer (8). Ensure the motor lead is still connected at the
screw. Tighten the screw.
6. Place the spring (9) on the brush (6) as shown above. Push
in and hook the spring clip (2). Repeat this procedure for the
other side.
6
7
8
9
2
7. Reinstall both inspection covers.
If electric motor overloads and stops running,
IMMEDIATELY turn the motor off and follow
the Pressure Relief Procedure in the Cleanup
section of this manual. Wait until the motor cools
(approximately 30 minutes). Then push in the
bubble top, manual reset button, turn the motor on
and pressurize the system.
6.7 Adjusting the Tracking of the Front Caster
The front caster is set by the factory to track in a straight line. Use the
following procedure if adjustment the caster becomes necessary.
1. Loosen the two hex screws (1) in the top of the caster
mounting bracket (2).
2. Turn the caster mounting bracket (2) slightly in the desired
direction.
i
The front caster locking pin must be engaged during
tracking adjustment.
3. Tighten the two hex screws (1).
4. Check the tracking of the front caster (3). If the caster does not
track straight, repeat the above procedure.
1
2
3
5
6
2
1
4
3
PowrLiner 17
GB
Maintenance
6.8 Replacing the Belt (Fig. 24)
Before replacing the belt on your unit, make sure
you have performed the “Pressure Relief Procedure”
as illustrated in the Operation section of this manual.
DO NOT attempt this repair while the unit is running.
i
The graphics below show a unit with a gas engine.
All instructions given in this section will apply to
both gas engine models and electric motor models
except where noted.
1. Loosen the bolt (1) on the front of the belt guard. Lift open
the front end of the belt guard (2) so that the front end of the
belt (3) is exposed.
2. Gently lift the front end of the gas engine / electric motor.
This will loosen the tension on the belt and make it easier to
remove.
PINCH HAZARD. Make sure your fingers remain clear
of the gas engine / electric motor mounting plate.
BURN HAZARD. Make sure the gas engine has had
time to sufficiently cool before touching it.
3. While the gas engine / electric motor is lifted up, remove the
belt from the front (4) and rear (5) pulleys.
4. Install the new belt:
a. Insert the belt into the xed section of the belt guard (6). Loop
the belt over the rear pulley (5) until the belt engages the
pulley groove.
b. Gently lift the front end of the gas engine / electric motor.
c. With the front end of the gas engine / electric motor lifted, loop
the other end of the belt around the front pulley (4).
d. Gently set the the gas engine / electric motor down. The
weight of the gas engine / electric motor will create tension in
the belt and prevent it from coming o.
Attention
Make sure the belt is not pinched or twisted in any
way once you have set the gas engine / electric
motor back into place.
e. Close the belt guard (2) and tighten the belt guard bolt (1).
18 PowrLiner
GB
Maintenance
6.9 Servicing the Hydraulic Motor (Fig. 25)
1
2
3
5
6
7
4
8
14
15
16
17
18
19
9
12
13
10
11
28
29
9
30
31
20
21
26
22
23
24
25
21
(B)
(A)
i
Refer to the ”SAE O-Ring Fitting Installation”
procedure at the end of this section for installation
instructions for item 22 and 24.
Perform this procedure using the necessary parts from Motor Service
Kit — Minor (P/N 235-050). If the hydraulic motor is operable, start
the machine and jog the piston rod (19) into its top position.
i
Servicing of the hydraulic motor should be carried
out in a clean, dust free area only. Any dust or
metallic particles left in the motor or entering it on
reassembly may damage the critical parts and aect
its service life and warranty. All parts should be
inspected for absolute cleanliness.
Disassembling the Hydraulic Motor
1. Disconnect the pressure hose assembly (B) from the elbow on
the back of the hydraulic pump.
2. Remove the two mounting screws and two lock washers that
attach the motor/pump assembly to the pump support on the
cart.
3. Place the motor/pump assembly in a vise, holding it securely
by the motor/pump block (31).
4. Remove cylinder head plug (1).
5. Loosen lock ring (28) with a spanner wrench and unthread
tube retaining nut on tee (24). Loosen tube retaining nut
on elbow (22). Slide the nut down. Remove motor tube
assembly (23). Slowly unthread cylinder head (8) and Iift it just
high enough above the cylinder (29) to reach the valve rod
assembly (18) with vise grip pliers.
6. The piston rod (19) should be near the top of its stroke for
disassembly. It may be necessary to use a wood or nylon driver
to push the piston rod up to its top position.
7. Grip the valve rod securely with vise grip pliers and then
remove the FlexLoc nut (3) from the top of the valve rod
assembly (18). Be careful that spool (10) does not fall. The
cylinder head (8) can now be lifted o. Unthread the cylinder
(29) from the motor/pump block (31).
i
An extra lock ring (28) can be used to jam the two
lock rings together on the cylinder and a pipe
wrench can be used to unthread the cylinder (29)
from the motor/pump block.
8. To remove the connecting pin (Fig. 26, 1), slide the retaining
ring (2) down with a small screwdriver, and then push the
connecting pin out.
1
2
9. Remove the piston rod assembly from the motor/pump block
(31).
10. Remove rod seal (30), being extremely careful not to scratch
the seal groove in the motor/pump block (31).
11. Place the piston retainer screw (14) on the piston rod assembly
in a vise. Slide a long bar through the hole at the base of the
piston rod for leverage, and unthread the piston rod from the
piston retainer screw.
12. Remove piston (19) and lift out valve rod assembly (18).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Titan PowrLiner 4955, 6955, 8955 Manuel utilisateur

Catégorie
Pulvérisateur de peinture
Taper
Manuel utilisateur