Bosch B36CL80ENS Guide d'installation

Catégorie
Réfrigérateurs-congélateurs
Taper
Guide d'installation
en Installation instructions and instructions for use ................ 2
fr Notice de montage et d’utilisation .................................... 34
es Instrucciones de uso y montaje ......................................... 68
Fridge-freezer
Réfrigérateur / congélateur combiné
Refrigerador/congelador
B36CL... EN...
en-us
2
enTable of contents
enInstallation i nst r uct i ons and i ns t r uct i ons for use
( Important safety instructions . . . . . . . . . . . . 3
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About these instructions . . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Restriction of user group. . . . . . . . . . . . . . . . . . . . . 3
Risk of explosion. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of electric shock . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of cold burns . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Risk of Injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Fire hazard/Danger due to refrigerants . . . . . . . . . . 4
Risk of fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Risk of suffocation. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
State of California Proposition 65 Warnings . . . . . . 4
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7 Environmental protection . . . . . . . . . . . . . . . 5
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Old appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Installation and connection . . . . . . . . . . . . . . 5
Contents of package. . . . . . . . . . . . . . . . . . . . . . . . 5
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . 6
Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Before using for the first time . . . . . . . . . . . . . . . .13
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical connection . . . . . . . . . . . . . . . . . . . . . . .13
* Getting to know your appliance . . . . . . . . . 14
Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Operating controls. . . . . . . . . . . . . . . . . . . . . . . . .15
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
1 Operating the appliance . . . . . . . . . . . . . . . . 20
Switching the appliance on . . . . . . . . . . . . . . . . . . 20
Switching off and disconnecting the appliance . . .20
Setting the temperature unit . . . . . . . . . . . . . . . . . 20
Setting the temperature. . . . . . . . . . . . . . . . . . . . .20
Setting cool-fresh compartment. . . . . . . . . . . . . . . 20
Super cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Super freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Energy saving mode . . . . . . . . . . . . . . . . . . . . . . . 21
Freshness mode . . . . . . . . . . . . . . . . . . . . . . . . . .21
Vacation mode . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Sabbath mode. . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Setting the light . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Change filter alarm . . . . . . . . . . . . . . . . . . . . . . . .22
M Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Temperature alarm . . . . . . . . . . . . . . . . . . . . . . . .22
o Home Connect. . . . . . . . . . . . . . . . . . . . . . . . 23
Setting up Home Connect . . . . . . . . . . . . . . . . . . 23
Installing updates for the Home Connect software 24
Information on data protection . . . . . . . . . . . . . . . 24
U Refrigerator compartment. . . . . . . . . . . . . . 25
Note when storing food . . . . . . . . . . . . . . . . . . . . 25
T Cool-fresh compartment . . . . . . . . . . . . . . . 25
Cool-fresh bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Storage recommendations . . . . . . . . . . . . . . . . . . 25
W Freezer compartment. . . . . . . . . . . . . . . . . . 26
V Water dispenser . . . . . . . . . . . . . . . . . . . . . . 26
Before using the appliance for the first time. . . . . 26
Observing drinking water quality . . . . . . . . . . . . . 26
Dispensing water . . . . . . . . . . . . . . . . . . . . . . . . . 26
; Ice maker. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Before using the appliance for the first time. . . . . 27
Switching ice cube production on or off . . . . . . . . 27
= Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the appliance interior. . . . . . . . . . . . . . . 28
Cleaning the fittings . . . . . . . . . . . . . . . . . . . . . . . 28
l Odors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9 Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
> Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Normal noises . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Preventing noises . . . . . . . . . . . . . . . . . . . . . . . . . 30
3 Faults – what to do? . . . . . . . . . . . . . . . . . . 31
Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Water dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ice maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4 Customer service. . . . . . . . . . . . . . . . . . . . . 33
Appliance self-test . . . . . . . . . . . . . . . . . . . . . . . . 33
Warranty statement. . . . . . . . . . . . . . . . . . . . . . . . 33
9 Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
Important safety instructions en-us
3
(Important safety instructions
Impor t ant saf et y i nst r uct i ons
READ INSTRUCTIONS - DO NOT DISCARD!
Definitions
9 WARNING
Non-observance of this warning could
result in death or serious injuries.
9 CAUTION
Non-observance of this warning could
result in slight or moderately serious
injuries.
NOTICE: Non-observance of this
information could damage the appliance.
Note: This indicates important information
and/or tips.
About these instructions
Read and follow the operating and
installation instructions.They contain
important information on how to install,
use and maintain the appliance.
Retain all documents for subsequent use
or for the next owner.
Introduction
This appliance complies with the relevant
safety regulations for electrical
appliances.
The refrigeration circuit has been
checked for leaks.
Restriction of user group
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Risk of explosion
Never use electric devices inside the
appliance (e.g. heaters or electric ice
makers).
Do not store products which contain
flammable propellants (e.g. spray cans)
or explosive substances in the appliance.
Only store high-proof alcohol tightly
closed and standing up.
Do not use other means to accelerate the
defrosting process other than those
recommended by the manufacturer.
Risk of electric shock
Improper installations or repairs may put the
user at considerable risk.
When installing the appliance, make sure
that the power cord does not get jammed
or damaged.
In order to avoid danger, if the power
cord is damaged, disconnect the
appliance from the power source
immediately. Have the power cord
replaced by the manufacturer, customer
service or a similarly qualified person.
Do not use multiple outlets, extension
cords, or adapters.
Before servicing the appliance or
carrying out installation work, disconnect
the appliance from the power source or
switch off the fuse.
Before cleaning the appliance, press the
ÿ power button to turn the appliance off.
Glass shelves and other equipment can
be moved while the appliance is
switched on.
Never cut through or remove the power
cord's third conductor (grounding
conductor).
Never defrost or clean the appliance
using a steam cleaner. The steam may
penetrate electrical parts and cause a
short circuit.
The appliance, cord and accessories
should only be repaired or replaced by
the manufacturer or an authorized
service provider.
9 Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
en-us Important safety instructions
4
Only use original parts supplied by the
manufacturer.
These parts come with a warranty from
the manufacturer that they satisfy the
safety requirements.
Risk of cold burns
Never put frozen food straight from the
freezer compartment into your mouth.
Avoid prolonged contact of skin with
frozen food, ice and the tubes in the
freezer compartment.
Risk of Injury
Containers which contain carbonated drinks
may burst.
Do not store containers which contain
carbonated drinks in the freezer
compartment.
Fire hazard/Danger due to
refrigerants
The tubes of the refrigeration circuit contain
a small quantity of an environmentally
friendly but flammable refrigerant (R600a).
If the refrigerant escapes, it may injure your
eyes or ignite.
Do not damage the tubes.
If the tubes are damaged:
Keep open flames and ignition sources
away from the appliance.
Ventilate the room.
Switch off the appliance and unplug the
power plug.
Please contact customer service.
Risk of fire
Portable multi-outlet power strips and
portable power supplies may overheat,
causing a fire.
Never leave portable multi-outlet power
strips or portable power supplies behind the
appliance.
Risk of suffocation
Keep children away from the packaging
and its parts.
To avoid having children climb into the
appliance, never remove the partition
wall of the frozen food bin (large).
Damage
To avoid damage:
Do not stand or lean on the base,
runners or doors.
Keep plastic parts and door seals free of
oil and grease.
Pull the power plug – not the power cord.
Weight
The appliance is very heavy. The appliance
should always be transported and set up by
at least 2 people.
~ "Installation and connection" on page 5
State of California Proposition 65
Warnings
This product may contain a chemical known
to the State of California, which can cause
cancer or reproductive harm. Therefore, the
packaging of your product may bear the
following label as required by California:
Intended use en-us
5
8Intended use
Intended us e
Use this appliance
only for cooling and freezing food, ice making
and water dispensing.
only in the home and in the home environment.
only according to these operating instructions.
This appliance is intended for use at an altitude of
max. 13123 ft (4000 meters) above sea level.
7Environmental protection
En v i r o n ment al pr ot ect i on
Packaging
All materials are environmentally safe and
recyclable:
Dispose of packaging in an environmentally
responsible manner.
Please ask your dealer or inquire at your local
authority about current means of disposal.
Old appliances
Valuable raw materials can be reclaimed by
recycling old appliances.
9 WARNING
CHILDREN MAY BECOME LOCKED IN THE
APPLIANCE AND SUFFOCATE!
Before disposing of your old appliance:
Remove the door.
Leave shelves and bins in the appliance to
prevent children from climbing in.
Keep children away from the discarded
appliance.
9 CAUTION
REFRIGERANT AND HARMFUL GASES MAY
ESCAPE.
Do not damage the tubes of the refrigeration
circuit and insulation.
1. Pull out the power plug.
2. Cut through the power cord.
3. Have the appliance disposed of properly.
5 Installation and
connection
Inst al lati on and connect i on
Contents of package
After unpacking, check all parts for damage during
transport.
In the event of damage, contact your dealer or our
after-sales service.
The delivery consists of the following parts:
Free-standing appliance
Interior fittings (depending on model)
Installation instructions and instructions for use
Statement of limited product warranty
Information on the energy consumption and
noises
Technical data
Refrigerant, cubic capacity and further technical
specifications can be found on the rating plate.
~ "Getting to know your appliance" on page 14
en-us Installation and connection
6
Installing the appliance
Installation location
The weight of the appliance may be up to 419 lb
(190 kg) depending on the model. The base must
be sufficiently stable and should not give. If
necessary, reinforce the floor.
Installation dimensions
Door opening angle
Minimum clearances
Leave a clearance of 1/2 ˝ (12.7 mm) above the
appliance.
Observe minimum clearances as follows:
Niche dimensions
If you install the appliance in a niche, adhere to the
following dimensions:
35
(905 mm)
71
½
(1815 mm)
24
(610 mm)
28 ¾
(731 mm)
25
(635 mm)
72 ″
(1830 mm)
33 ½
(852 mm)
90°90°
118°
9
⁷/
(239 mm)
1
¾
(45 mm)
43
(1102 mm)
54
⁷/
(1383 mm)
(3,2 mm)
(3,2 mm)
1 ″
(25 mm)
36
(914 mm)
72
(1830 mm)
25
(635 mm)
Installation and connection en-us
7
Ventilation
Never cover or block ventilation openings.
Aligning the appliance
9 CAUTION
To avoid damage to the floor, always move the
appliance with the height-adjustable feet
screwed upwards.
The two front height-adjustable feet must
always be in contact with the floor to avoid the
appliance from rolling or tipping when the door
is opened.
Rollers are located under the appliance for easy
movement and alignment:
1. Place the appliance vertically on a firm, level
floor.
2. Using a wrench, screw down both of the front
height-adjustable feet so that they touch the floor.
3. Compensate for floor unevenness with the front
height-adjustable feet.
Note: To align, use a level.
13
en-us Installation and connection
8
Align refrigerator compartment doors
Align the vertical gap of the doors:
Note: Remove the contents from the doors, if
present.
1. Remove the screw T20 and cover cap on the
door hinge.
2. Loosen the safety screw.
9 CAUTION
Do not remove the safety screw.
3. Turn the adjustment screw until the desired
position is reached when the door is closed.
To move the upper end of the door outwards,
turn clockwise.
To move the upper end of the door inwards,
turn counterclockwise.
4. To check the position, close the door and correct
if necessary.
5. Tighten the safety screw again.
6. Fit the cover cap and screw in the screw T20
again.
Installation and connection en-us
9
Align the horizontal gap between the doors:
9 CAUTION
To avoid damage to the appliance, move the
right-hand door down if the door pillar at the top
collides with the housing.
Note: Remove the contents from the doors, if
present.
1. Open the door and drawer.
2. Lift the door and insert a screwdriver into the door
hinge from below.
3. Push up the adjustable part and turn by 60° until
the desired position is reached.
The door height can be set at 2 levels,
adjusted by 1/16" (1.5 mm) in each case. The
higher level is followed by the lower. The
adjustable part engages as soon as a position
is reached.
To move the door up, turn clockwise.
To move the door down, turn
counterclockwise.
4. To check the position, close the door and drawer
and correct if necessary.
en-us Installation and connection
10
Aligning the drawers
You can align the drawer vertically:
1. Open the drawer as far as it will go and remove
the bin.
2. Remove the center screws on both sides.
Note: If you want to reset the drawer to the factory
settings, keep the screws.
3. Loosen the upper screw on both sides.
Note: Do not remove the screws.
4. Lift the drawer and remove the lower screws on
both sides.
5. Move the drawer up or down to the required
position and insert the lower screw in one of the
available holes.
Note: The drawer can be adjusted by 1/16" (2 mm)
up and down.
6. Retighten all the screws.
7. To check the position, close the drawer and
correct if necessary.
Installation and connection en-us
11
You can adjust the angle of the drawer:
1. Open the drawer as far as it will go and remove
the bin.
2. Remove the center screws on both sides.
Note: If you want to reset the drawer to the factory
settings, keep the screws.
3. Loosen the upper and lower screw on both sides.
Note: Do not remove the screws.
4. Move drawer on the lower screw to the left or
right into the required position and tighten the
screw.
5. Retighten all the screws.
6. To check the position, close the drawer and
correct if necessary.
en-us Installation and connection
12
Saving energy
If you follow the instructions below, your appliance will use less power.
Note:
The arrangement of the fittings does not affect the energy consumption of the appliance.
--------
Installing the appliance
Keep the appliance out of direct sunlight. The appliance needs to cool less frequently at low ambient tempera-
tures and therefore consumes less power.
Install the appliance as far away as possible from heating elements,
cooker and other heat sources:
At least 1¼” (3 cm) from electric or gas cookers.
At least 11¾" (30 cm) from oil or solid-fuel cookers.
Select an installation location at a room temperature of approx. 68 °F
(20 °C).
Do not cover or block the ventilation openings. The appliance needs to cool less frequently if the warm air can
escape and therefore consumes less power.
Ventilate the room daily.
Using the appliance
Open the appliance door only briefly. The air in the appliance does not warm up as intensely. The appliance
needs to cool less frequently and therefore consumes less power.
Transport purchased food in a cooler and place in the appliance
quickly.
Allow warm food and drinks to cool down before placing in the appli-
ance.
Thaw frozen food in the refrigerator compartment to utilize the low
temperature of the frozen food.
Always leave some space between the food and to the back panel. The air can circulate and the humidity will remain constant. The appli-
ance needs to cool less frequently and therefore consumes less
power.
Pack food airtight.
Do not cover or block the ventilation openings. The appliance consumes less power if the warm air can escape.
Vacuum the ventilation openings once a year or as frequently as
needed.
Installation and connection en-us
13
Before using for the first time
1. Remove information material, adhesive tape and
protective foil.
2. Remove the power cord from the appliance.
3. Clean the appliance.
4. Install the equipment.
~ "Equipment" on page 16
Water connection
9 CAUTION
Never bend, crush, modify or cut water hoses.
Never pull on the water hose on the rear panel
of the appliance.
To avoid damage to the appliance and to
ensure its proper functioning, it should only be
connected to a drinking water line.
To avoid water damage, a shut-off valve must
be installed.
Notes
Installation and connection of the appliance must
be carried out by a qualified technician.
Observe the local regulations for water
connection.
Water pressure of drinking water line
9 CAUTION
To avoid damage to the appliance, a pressure
relief valve must be installed between the
drinking water connection and the hose set if
the water pressure exceeds the maximum
value.
Note: If the water pressure is too low, this will impair
functioning of the appliance.
Water pressure min.: 0.2 MPa (2 bar / 29 psi)
Water pressure max.: 0.8 MPa (8 bar / 116 psi)
Electrical connection
9 CAUTION
Do not connect the appliance to electronic
energy saver plugs.
Note: You can connect the appliance to mains-
controlled and sine-controlled inverters.
Mains-controlled inverters are used for photovoltaic
systems which are connected directly to the national
grid. Sine-controlled inverters must be used for
isolated applications. Isolated applications, e.g. on
ships or in mountain lodges, are not directly
connected to the national grid.
1. Insert the power cord plug.
2. Check that the power outlet has been installed
according to the regulations and complies with
the requirements.
Requirements for power outlets
Maximum simultaneous load
3. Connect the appliance to an outlet near the
appliance.
The outlet must also be freely accessible
following installation of the appliance.
9 WARNING
RISK OF ELECTRIC SHOCK!
Never use multiple outlets, extension cords
or adapters.
The appliance must be grounded correctly.
Never cut through or remove the power
cord's third conductor (grounding
conductor).
9 WARNING
RISK OF ELECTRIC SHOCK!
If the power cord is too short, never use
multiple outlets or extension cords.Instead,
please contact customer service.
Power outlet with protective
conductor:
110 V ... 127 V with
60 Hz
Fuse: 10 A ... 16 A
Appliance: 6 A
en-us Getting to know your appliance
14
*Getting to know your
appliance
Get t i ng to know your appl i anc e
Appliance
#
3
+
)*
)B
)R
)b
):
)Z
)j
1"
1*
12
)2
)J
1:
P
`
h
X
H
)"
(
0
@
8
# Refrigerator compartment
+ Cool-fresh compartment
3 Freezer compartment
( Operating controls
0 Equipment bar
8 Bin (hanging)
@ Shelf (hanging)
H Water dispenser
P Pull-out bin
X Controls for cool-fresh compartment
` Cool-fresh bin
h Ice maker
)" Ice cube bin with ice scoop
)* Interior light
)2 Water filter
): Butter and cheese compartment
)B Bottle shelf (hanging)
)J Rating plate
)R Door pillar with condensation protection
)Z Fixed shelf
)b Storage compartment for large bottles
)j Ethylene absorber
1" Frozen food bin (small)
1* Frozen food bin (flat)
12 Frozen food bin (large)
1: Height-adjustable feet
Getting to know your appliance en-us
15
Operating controls
Controls submenu
(08@ H P X `h)")*)2):
( Refrigerator compartment Û super button
Switches super cooling on or off.
0 Refrigerator compartment temperature
display
Indicates the set temperature in °C/°F.
8 Refrigerator compartment Y/X button
Sets the temperature of the refrigerator
compartment.
@ fresh button
Switches freshness mode on or off.
H eco button
Switches energy-saving mode on or off.
P vacation button
Switches vacation mode on or off.
X ÿ power button
Switches the appliance on or off.
` alarm off button
Switches off the alarm.
h menu button
Opens the menu.
)" change filter button
Switches the change filter alarm off.
)* Freezer compartment ¾ super button
Switches super freezing on or off.
)2 Freezer compartment temperature display
Indicates the set temperature in °C/°F.
): Freezer compartment Y/X button
Sets the temperature of the freezer
compartment.
P`hXH(0 @8
( Submenu display
Displays the selected submenu.
0 Y/X submenu button
Used to navigate through the submenu.
8 connect button
Opens the Home Connect menu.
@ light settings button
Opens the lighting menu.
H °C/°F button
Opens the temperature unit menu.
P Settings display
Displays the settings of the submenu.
X Y/X Settings button
Changes the settings of the submenu.
` alarm off button
Opens the alarm menu.
h change filter button
Opens the filter menu.
en-us Getting to know your appliance
16
Controls for cool-fresh compartment
Equipment
Storage compartment
You can remove the storage compartment:
Lift up the storage compartment and remove.
Shelf
You can remove and adjust the shelf:
Lift shelf and remove.
Notes
Do not cover the ventilation openings.
Insert shelf carefully to avoid scratching the
appliance.
Ensure that the hooks are fully inserted and the
shelf is horizontal.
PXH(0 @8
( 29°F ^ button
Sets the temperature in the cool-fresh
compartment to 29 °F (–2 °C), and the
humidity to low.
0 32°F ^ button
Sets the temperature in the cool-fresh
compartment to 32 °F (0 °C), and the
humidity to low.
8 32°F ^^ button
Sets the temperature in the cool-fresh
compartment to 32 °F (0 °C), and the
humidity to high.
@ 34°F
^ button
Sets the temperature in the cool-fresh
compartment to 34 °F (1 °C), and the
humidity to low.
H 40°F
^ button
Sets the temperature in the cool-fresh
compartment to 40 °F (4 °C), and the
humidity to low.
P unlock button cool-fresh compartment
Unlocks the controls of the cool-fresh
compartment.
X Light bar custom|
Lights up if user-defined settings have
been set via the Home Connect app. For
more information, see the Home Connect
app.
Getting to know your appliance en-us
17
Equipment bar
You can remove and adjust the equipment bar:
1. Lift equipment bar and remove.
2. When re-inserting, insert hooks on back of the
equipment bar at same height to make the
equipment bar level.
Note: Insert the equipment bar carefully to avoid
scratching the appliance.
Note: You can remove the bin (hanging), the shelf
(hanging) and the bottle shelf (hanging) and move
them laterally.
Pull-out bin
You can remove the bin:
Pull out the bin all the way, lift at the front and
remove.
You can insert the bin:
Pull out the telescopic rails all the way
Place the bin on the telescopic rails and push into
the appliance until it engages.
Fixed shelf
You can remove the shelf:
Open the bin, lift the shelf at the front and
remove.
en-us Getting to know your appliance
18
Cool-fresh bin
You can remove the bin:
1. Pull the drawer all the way out.
2. Lift the bin at the front and remove.
Note: During insertion, the rail guide of the bin and
drawer must fit together.
Frozen food bin (small)
You can remove the bin:
Pull out the bin all the way, lift at the front and
remove.
You can insert the bin:
Pull out the telescopic rails all the way.
Place the bin on the telescopic rails and push into
the appliance until it engages.
Ice cube bin
You can remove the ice cube bin:
Pull out the frozen food bin (flat) as far as it will
go and remove the ice cube bin.
Notes
Use the ice scoop to remove ice cubes from the
ice cube bin.
To ensure that ice cube production does not stop
too soon, do not store the ice scoop in the ice
cube bin.
Frozen food bin (flat)
You can take out the frozen food bin (flat):
1. Pull the frozen food bin all the way out.
2. Pull the frozen food bin (flat) out, lift and remove.
Getting to know your appliance en-us
19
Frozen food bin (large)
9 CAUTION
To avoid damage to equipment, never remove
the partition wall from the frozen food bin
(large).
You can take out the frozen food bin (large):
1. Pull the freezer compartment drawer all the way
out and remove the frozen food bin (flat).
2. Lift the frozen food bin (large) and remove it.
Water filter
Note: After installing a new water filter, for hygiene
reasons discard the ice cubes produced within the
first 24 hours or dispense water for 5 minutes and
discard.
The water filter supplied filters particles and the taste
of chlorine out of the water, not bacteria or microbes:
Replace the water filter every 6 months or as
frequently as needed.
You can also use the appliance without an internal
water filter if you use an external water filter system.
To do this, replace the water filter with a bypass filter:
The bypass filter filters coarse particles from the
drinking water and can be cleaned as required.
The bypass filter can remain in the appliance
permanently and does not need to be changed.
Switch off the change filter alarm every 6 months.
~ "Change filter alarm" on page 22
A new water filter or bypass filter can be purchased
from customer service or a specialist dealer.
Change water filter or replace with bypass filter:
Notes
When changing, some water will drip from the
filter. Wipe drips dry with a soft cloth.
You can dispose of the used filter with your
household garbage.
1. Reach into the lower recess of the filter cover,
pull forwards slightly and move to the bottom left.
2. Turn the filter 90° counterclockwise and remove.
3. Insert the new filter in the filter opening to the
stop and turn 90° clockwise as far as it will go.
4. Move the filter cover up to the right again and
slide back as far as it will go.
Ethylene absorber
Fasten the ethylene absorber in the cool-fresh bin.
Note: For more information about installation and
use, see the installation and operating instructions
for the ethylene absorber.
en-us Operating the appliance
20
1Operating the appliance
Oper at i ng the appl i ance
Switching the appliance on
1. Press the ÿ power button.
The appliance begins to cool. The warning sound,
the flashing freezer compartment temperature
display and the illuminated alarm off button
indicate that the freezer compartment is still too
warm.
2. Press the alarm off button.
The warning sound switches off.
3. Set the required temperature.
Operating tips
When the appliance has been switched on, it may
take several hours until the set temperatures have
been reached. Do not put in any food until the
selected temperature has been reached.
The fully automatic NoFrost system ensures that
the appliance remains frost-free. Defrosting is not
required.
The front sides of the housing are partly heated
slightly. This prevents condensation in the area
of the door seal.
Switching off and disconnecting the
appliance
Switching off the appliance
Press ÿ power button.
The appliance is no longer cooling.
Disconnecting the appliance
If you do not use the appliance for a prolonged
period:
1. Turn off the water supply to the appliance.
2. Remove groceries.
3. Press the ÿ power button.
4. Pull out the power plug or switch off the fuse.
The appliance is no longer cooling.
5. Remove the water filter, empty the ice cube bin
and clean the appliance.
6. Leave the doors and drawers of the appliance
open.
Setting the temperature unit
You can choose between the units °C and °F:
1. Press menu button.
2. Press °C/°F button.
3. Press Y/X Settings button until settings display
shows °C or °F.
4. Press menu button.
The setting is saved.
Setting the temperature
Recommended temperature
Cooling compartment
Keep pressing the Y/X button until the display
indicates the required temperature.
Freezer compartment
Keep pressing Y/X button until the display
indicates the required temperature.
Setting cool-fresh compartment
You can set the temperature and the humidity of the
cool-fresh compartment using pre-defined storage
settings:
1. Open the cool-fresh compartment drawer.
2. Press any button of the cool-fresh compartment
controls.
3. Press and hold the unlock cool-fresh
compartment button until the light bar is fully
illuminated.
4. Press the required storage setting button.
5. Close the cool-fresh compartment drawer.
The setting is saved.
Super cooling
Super cooling cools the refrigerator compartment as
cold as possible.
Switch on super cooling, e.g.:
Before placing large quantities of food into the
compartment
For cooling drinks quickly
Note: When super cooling is switched on, increased
operating noises may occur.
After approx. 6 hours, the appliance switches to
normal operation.
Switch super cooling on/off:
Press Û super button refrigerator compartment.
When super cooling is switched on, the button
lights up.
Refrigerator compartment: 37 °F (3 °C)
Cool-fresh compartment: 32 °F (0 °C)
Freezer compartment: 0 °F (–18 °C)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102

Bosch B36CL80ENS Guide d'installation

Catégorie
Réfrigérateurs-congélateurs
Taper
Guide d'installation