Bosch B36CD50SNB/03 Le manuel du propriétaire

en Installation and Using Instructions ...................................... 2

fr Notice de montage et d’utilisation .................................... 35

es Instrucciones de uso y montaje ......................................... 69

Refrigerator-freezer

Réfrigérateur / congélateur combiné

Refrigerador/congelador

B36CD...

en-us

2

en Table of contents

enInstallation and Us i n g I nst r uct i ons

( Important safety instructions . . . . . . . . . . . . 3

Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

About these instructions . . . . . . . . . . . . . . . . . . . . . 3

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Restriction of user group. . . . . . . . . . . . . . . . . . . . . 3

Risk of explosion. . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Risk of electric shock . . . . . . . . . . . . . . . . . . . . . . . 3

Risk of cold burns . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Risk of injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Fire hazard/Danger due to refrigerants . . . . . . . . . . 4

Risk of fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Risk of suffocation. . . . . . . . . . . . . . . . . . . . . . . . . . 4

Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

State of California Proposition 65 Warnings . . . . . . 4

8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7 Environmental protection . . . . . . . . . . . . . . . 5

Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Old appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5 Installation and connection . . . . . . . . . . . . . . 5

Contents of package. . . . . . . . . . . . . . . . . . . . . . . . 5

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Installing the appliance . . . . . . . . . . . . . . . . . . . . . . 5

Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Before using for the first time . . . . . . . . . . . . . . . .13

Water connection . . . . . . . . . . . . . . . . . . . . . . . . .13

Electrical connection . . . . . . . . . . . . . . . . . . . . . . .13

* Getting to know your appliance . . . . . . . . . 14

Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Operating controls. . . . . . . . . . . . . . . . . . . . . . . . .15

Ice and water dispenser . . . . . . . . . . . . . . . . . . . . 16

Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1 Operating the appliance . . . . . . . . . . . . . . . . 19

Switching the appliance on . . . . . . . . . . . . . . . . . . 19

Switching off and disconnecting the appliance . . . 19

Setting the temperature unit . . . . . . . . . . . . . . . . .19

Setting the temperature. . . . . . . . . . . . . . . . . . . . .20

Super cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Super freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Energy saving mode . . . . . . . . . . . . . . . . . . . . . . . 20

Freshness mode . . . . . . . . . . . . . . . . . . . . . . . . . .20

Vacation mode . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Sabbath mode. . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Setting the light . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Change filter alarm . . . . . . . . . . . . . . . . . . . . . . . . 21

Switching the ice and water dispenser

button lock (child lock) on or off . . . . . . . . . . . . . .21

Light of ice and water dispenser. . . . . . . . . . . . . . 21

Setting the bottle fill water amount . . . . . . . . . . . . 22

Switching the ice and water dispenser and

ice maker on or off . . . . . . . . . . . . . . . . . . . . . . . . 22

M Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Temperature alarm . . . . . . . . . . . . . . . . . . . . . . . . 22

o Home Connect. . . . . . . . . . . . . . . . . . . . . . . . 23

Setting up Home Connect . . . . . . . . . . . . . . . . . . 23

Installing updates for the

Home Connect software . . . . . . . . . . . . . . . . . . . . 24

Information on data protection . . . . . . . . . . . . . . . 25

Remote Diagnostics . . . . . . . . . . . . . . . . . . . . . . . 25

U Refrigerator compartment. . . . . . . . . . . . . . 25

Vegetable bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Cold storage bin. . . . . . . . . . . . . . . . . . . . . . . . . . 26

Note when storing food . . . . . . . . . . . . . . . . . . . . 26

W Freezer compartment. . . . . . . . . . . . . . . . . . 26

; Ice and water dispenser . . . . . . . . . . . . . . . 26

Before using the appliance for the first time. . . . . 26

Observing drinking water quality . . . . . . . . . . . . . 26

Operation of the ice and water dispenser. . . . . . . 27

Dispensing ice or water . . . . . . . . . . . . . . . . . . . . 27

Bottle fill option. . . . . . . . . . . . . . . . . . . . . . . . . . . 27

= Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Cleaning the appliance interior. . . . . . . . . . . . . . . 28

Cleaning the equipment . . . . . . . . . . . . . . . . . . . . 28

l Odors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9 Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

> Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Normal noises . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Preventing noises . . . . . . . . . . . . . . . . . . . . . . . . . 31

3 Troubleshooting – what to do?. . . . . . . . . . 31

Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4 Customer service. . . . . . . . . . . . . . . . . . . . . 34

Appliance self-test . . . . . . . . . . . . . . . . . . . . . . . . 34

Warranty statement. . . . . . . . . . . . . . . . . . . . . . . . 34

9 Important safety instructions

READ INSTRUCTIONS - DO NOT DISCARD!

Important safety instructions en-us

3

(Important safety instructions

Impor t ant saf et y i nst r uct i ons

READ INSTRUCTIONS - DO NOT DISCARD!

Definitions

9 WARNING

Non-compliance with safety information

that could lead to a dangerous situation

with risk of death or serious injury.

9 CAUTION

Non-compliance with safety information

that could lead to a dangerous situation

with risk of injury.

NOTICE: Non-observance of this

information could damage the appliance.

Note: This indicates important information

and/or tips.

About these instructions

■ Read and follow the operating and

installation instructions. They contain

important information on how to install,

use and maintain the appliance.

■ Retain all documents for subsequent use

or for the next owner.

Introduction

■ This appliance complies with the relevant

safety regulations for electrical

appliances.

■ The refrigeration circuit has been

checked for leaks.

Restriction of user group

■ Avoid placing children and vulnerable

persons at risk.

■ This appliance may be used by children

and persons who have reduced physical,

sensory or mental abilities or inadequate

experience and/or knowledge, provided

they are supervised or have been

instructed on how to use the appliance

safely and have understood the resulting

dangers.

■ Children should be supervised to ensure

that they do not play with the appliance.

Risk of explosion

■ Never use electric devices inside the

appliance (e.g. heaters or electric ice

makers).

■ Do not store products which contain

flammable propellants (e.g. spray cans)

or explosive substances in the appliance.

■ Only store high-proof alcohol tightly

closed and standing up.

■ Do not use other means to accelerate the

defrosting process other than those

recommended by the manufacturer.

Risk of electric shock

Improper installations or repairs may put the

user at considerable risk.

■ When installing the appliance, make sure

that the power cord does not get jammed

or damaged.

■ In order to avoid danger, if the power

cord is damaged, disconnect the

appliance from the power source

immediately. Have the power cord

replaced by the manufacturer, customer

service or a similarly qualified person.

■ Do not use multiple outlets, extension

cords, or adapters.

■ Before servicing the appliance or

carrying out installation work, disconnect

the appliance from the power source or

switch off the circuit breaker.

■ Before cleaning the appliance, press the

ÿ power button to turn the appliance off.

Glass shelves and other equipment can

be moved while the appliance is

switched on.

■ Never cut through or remove the power

cord's third conductor (grounding

conductor).

■ Never defrost or clean the appliance

using a steam cleaner. The steam may

penetrate electrical parts and cause a

short circuit.

9 Important safety instructions

READ INSTRUCTIONS - DO NOT DISCARD!

en-us Important safety instructions

4

■ The appliance, cord and accessories

should only be repaired or replaced by

the manufacturer or an authorized

service provider.

■ Only use original parts supplied by the

manufacturer.

These parts come with a warranty from

the manufacturer that they satisfy the

safety requirements.

Risk of cold burns

■ Never put frozen food straight from the

freezer compartment into your mouth.

■ Avoid prolonged skin contact with frozen

food, ice or any other surface inside the

freezer compartment.

Risk of injury

■ Containers with carbonated drinks may

burst.

■ Do not store containers which contain

carbonated drinks in the freezer

compartment.

Fire hazard/Danger due to

refrigerants

The tubes of the refrigeration circuit contain

a small quantity of an environmentally

friendly but flammable refrigerant (R600a).

If the refrigerant escapes, it may injure your

eyes or ignite.

■ Do not damage the tubes.

If the tubes are damaged:

■ Keep open flames and ignition sources

away from the appliance.

■ Ventilate the room.

■ Switch off the appliance and unplug the

power cord.

■ Please contact customer service.

Risk of fire

Portable multi-outlet power strips and

portable power supplies may overheat,

causing a fire.

■ Never leave portable multi-outlet power

strips or portable power supplies behind

the appliance.

Risk of suffocation

■ Keep children away from the packaging

and its parts.

■ To avoid having children climb into the

appliance, never remove the partition

wall of the frozen food bin (large).

Damage

To avoid damage:

■ Do not stand or lean on the base,

runners or doors.

■ Keep plastic parts and door seals free of

oil and grease.

■ Pull the power plug – not the power cord.

Weight

The appliance is very heavy. The appliance

should always be transported and set up by

at least 2 people.

~ "Installation and connection" on page 5

State of California Proposition 65

Warnings

This product may contain a chemical known

to the State of California, which can cause

cancer or reproductive harm. Therefore, the

packaging of your product may bear the

following label as required by California:

Intended use en-us

5

8Intended use

Intended us e

Use this appliance

■ only for cooling and freezing food, ice making

and water dispensing.

■ only in the home and in the home environment.

■ only according to these operating instructions.

This appliance is intended for use at an altitude of

max. 13123 ft (4000 meters) above sea level.

7Environmental protection

En v i r on ment al pr ot ec t i on

Packaging

All materials are environmentally safe and

recyclable:

■ Dispose of packaging in an environmentally

responsible manner.

■ Please ask your dealer or inquire at your local

authority about current means of disposal.

Old appliances

Valuable raw materials can be reclaimed by

recycling old appliances.

9 WARNING

CHILDREN MAY BECOME LOCKED IN THE

APPLIANCE AND SUFFOCATE!

Before disposing of your old appliance:

■ Remove the doors and drawer.

■ Leave shelves and bins in the appliance to

prevent children from climbing in.

■ Keep children away from the discarded

appliance.

9 CAUTION

REFRIGERANT AND HARMFUL GASES MAY

ESCAPE.

Do not damage the tubes of the refrigeration

circuit and insulation.

1. Pull out the power cord.

2. Cut through the power cord.

3. Have the appliance disposed properly.

5 Installation and

connection

Inst al lat ion and connect i on

Contents of package

After unpacking, check all parts for damage during

transportation.

In the event of damage, contact your dealer or our

customer service.

~ "Customer service" on page 34

The delivery consists of the following parts:

■ Free-standing appliance

■ Installation material

■ Equipment (depending on model)

■ Installation and Using Instructions

■ Statement of limited product warranty

■ Information on the energy consumption and

noises

Technical data

Refrigerant, cubic capacity and further technical

specifications can be found on the rating plate.

~ "Getting to know your appliance" on page 14

Installing the appliance

Installation location

Follow these instructions when installing your

appliance.

9 WARNING

RISK OF EXPLOSION!

If the appliance is installed in a space that is

too small, a leak in the refrigeration circuit may

result in a flammable mixture of gas and air.

Only install the appliance in a space with a

volume of at least 36 ft³(1 m³) per 0.3 oz (8 g)

of refrigerant. The amount of refrigerant is

indicated on the rating plate.

~ "Getting to know your appliance"

on page 14

Depending on the model, the weight of the

appliance factory-made may be up to 320 lb

(145 kg). The subfloor must be sufficiently stable to

bear the weight of the appliance.

en-us Installation and connection

6

Installation dimensions

Door opening angle

If the installation location limits the door opening

angle to less than 118°, buy a 90° door stopper

from our customer service.

~ "Customer service" on page 34

Minimum clearances

Leave a clearance of 1/2 ˝ (12.7 mm) above the

appliance.

Observe minimum clearances as follows:

Niche dimensions

If you install the appliance in a niche, adhere to the

following dimensions:

35

⅝

″

(905 mm)

69

½

″

(1765 mm)

24

″

(610 mm)

28

¾

″

(731 mm)

25

″

(635 mm)

70 ″

(1780 mm)

42

¾

″

(1085 mm)

90°90°

118°

10

⁹/

″

(268 mm)

3

¹¹/

″

(93 mm)

1

¾

″

(45 mm)

43

⅜

″

(1102 mm)

56

¾

″

(1441 mm)

⅛

″

(3,2 mm)

⅛

″

(3,2 mm)

1 ″

(25 mm)

36

″

(914 mm)

70

″

(1780 mm)

25

″

(635 mm)

Installation and connection en-us

7

Ventilation

Never cover or block ventilation openings.

Installing the door handle

1. Fit the handle vertically onto the pre-assembled

bolts.

Note: The holes in the handle must face up and

down.

2. Use a 2.5 mm Allen wrench to tighten the top and

bottom pre-assembled screws clockwise.

Installing the drawer handle

1. Fit the handle horizontally onto the pre-assembled

bolts.

Note: The holes in the handle must be facing down.

2. Use a 2.5 mm Allen wrench to tighten the bottom

pre-assembled screws clockwise.

Aligning the appliance

9 CAUTION

■ To avoid damaging the floor, always move the

appliance with the height-adjustable feet

screwed upwards.

■ The two front height-adjustable feet must

always be in contact with the floor to avoid the

appliance from rolling or tipping when the door

is opened.

Rollers are located under the appliance for easy

movement and alignment:

1. Place the appliance vertically on a firm and

leveled floor.

2. Using a wrench, screw down both of the front

height-adjustable feet so that they touch the floor.

3. Compensate for floor unevenness with the front

height-adjustable feet.

Note: To align, use a level.

13

en-us Installation and connection

8

Align refrigerator compartment doors

Aligning the vertical gap of the doors:

Note: Remove any items contained in the doors.

1. Remove T20 screw and cover cap on the door

hinge.

2. Loosen the safety screw.

9 CAUTION

Do not remove the safety screw.

3. With the door closed, turn the adjustment screw

until the desired position is reached.

– To move the upper end of the door outwards,

turn clockwise.

– To move the upper end of the door inwards,

turn counterclockwise.

4. Close the door to check the position and correct

if necessary.

5. Tighten the safety screw again.

6. Fit the cover cap and screw in T20 screw again.

Installation and connection en-us

9

Aligning the horizontal gap between the doors and

drawer:

9 CAUTION

To avoid damaging the appliance, move the

right-hand door down if the top of the door pillar

interferes with the housing.

Note: Remove any items contained in the doors.

1. Open the door and drawer.

2. Lift the door and insert a screwdriver into the door

hinge from below.

3. Push up the adjustable part and turn by 60° until

the desired position is reached.

– The door height can be set at 2 levels,

adjusted by 1/16" (1.6 mm) in each case. The

higher level is followed by the lower. The

adjustable part engages as soon as a position

is reached.

– To move the door up, turn clockwise.

– To move the door down, turn

counterclockwise.

4. Close the door and drawer to check the position

and correct if necessary.

en-us Installation and connection

10

Aligning the drawers

You can align the drawer vertically:

1. Open the drawer as far as it will go and remove

the bin.

2. Remove the center screw on both sides.

Note: If you want to reset the drawer to the factory

settings, keep the screws.

3. Loosen the upper screw on both sides.

Note: Do not remove the screws.

4. Lift the drawer and remove the lower screw on

both sides.

5. Move the drawer up or down to the required

position and screw the lower screw into one of

the available holes.

Note: The drawer can be adjusted by 1/16"

(1.6 mm) up and down.

6. Retighten all the screws.

7. To check the position, close the drawer and

correct if necessary.

Installation and connection en-us

11

You can adjust the angle of the drawer:

1. Open the drawer as far as it will go and remove

the bin.

2. Remove the center screw on both sides.

Note: If you want to reset the drawer to the factory

settings, keep the screws.

3. Loosen the upper and lower screw on both sides.

Note: Do not remove the screws.

4. Move the drawer on the lower screw to the left or

right into the required position and tighten the

screw.

5. Retighten all the screws.

6. To check the position, close the drawer and

correct if necessary.

en-us Installation and connection

12

Saving energy

If you follow the instructions below, your appliance will use less power.

Note:

The arrangement of the equipment does not affect the energy consumption of the appliance.

--------

Installing the appliance

Keep the appliance out of direct sunlight. The appliance needs to cool less frequently at low ambient tempera-

tures and therefore consumes less power.

Install the appliance as far away as possible from heating elements,

cooker and other heat sources:

At least 1¼” (3 cm) from electric or gas cookers.

At least 11¾" (30 cm) from oil or solid-fuel cookers.

Select an installation location at a room temperature of approx. 68 °F

(20 °C).

Do not cover or block the ventilation openings. The appliance needs to cool less frequently if the warm air can

escape and therefore consumes less power.

Ventilate the room daily.

Using the appliance

Open the appliance door only briefly. The air in the appliance does not warm up as intensely. The appliance

needs to cool less frequently and therefore consumes less power.

Transport purchased food in a cooler and place in the appliance

quickly.

Allow warm food and drinks to cool down before placing in the appli-

ance.

Thaw frozen food in the refrigerator compartment to utilize the low

temperature of the frozen food.

Always leave some space between the food and to the back panel. The air can circulate and the humidity will remain constant. The appli-

ance needs to cool less frequently and therefore consumes less

power.

Pack food airtight.

Do not cover or block the ventilation openings. The appliance consumes less power if the warm air can escape.

Vacuum the ventilation openings once a year or as frequently as

needed.

Installation and connection en-us

13

Before using for the first time

1. Remove information material, adhesive tape and

protective foil.

2. Remove the power cord from inside the

appliance.

3. Clean the appliance.

~ "Cleaning" on page 28

4. Install the equipment.

~ "Equipment" on page 16

Water connection

9 CAUTION

■ Never bend, crush, modify or cut water hoses.

■ Never pull on the water hose on the rear panel

of the appliance.

■ To avoid damaging the appliance and to

ensure proper functioning, it should only be

connected to a drinking water line.

■ To avoid water damage, a shut-off valve must

be installed.

Notes

■ Installation and connection of the appliance must

be carried out by a qualified technician.

■ The shut-off valve must also be freely accessible

following installation of the appliance.

■ Observe the local regulations for water

connection.

The water quality of the water connection is tested:

■ Rinse the water line leading to the appliance

thoroughly until there are no more sediments or

turbidity in the water.

■ If the water line leading to the appliance still

contains sediments or turbidity, install an external

water filter system.

Water pressure of drinking water line

9 CAUTION

To avoid damage to the appliance, a pressure

relief valve must be installed between the

drinking water connection and the hose set if

the water pressure exceeds the maximum

value.

Note: If the water pressure is too low, this will impair

functioning of the appliance.

■ Water pressure min.: 0.2 MPa (2 bar / 29 psi)

■ Water pressure max.: 0.8 MPa (8 bar / 116 psi)

Electrical connection

9 CAUTION

Do not connect the appliance to electronic

energy saver plugs.

Note: You can connect the appliance to mains-

controlled and sine-controlled inverters.

Mains-controlled inverters are used for photovoltaic

systems which are connected directly to the national

grid. Sine-controlled inverters must be used for

isolated applications. Isolated applications, e.g. on

ships or in mountain lodges, are not directly

connected to the national grid.

1. Insert the power cord plug in the rear of the

appliance.

2. Check that the power outlet has been installed

according to the regulations and complies with

the requirements.

Requirements for power outlets

Maximum load

3. Connect the appliance to an outlet near the

appliance.

The outlet must also be freely accessible

following installation of the appliance.

9 WARNING

RISK OF ELECTRIC SHOCK!

Never use multiple outlets, extension cords

or adapters.

The appliance must be grounded correctly.

Never cut through or remove the power

cord's third conductor (grounding

conductor).

9 WARNING

RISK OF ELECTRIC SHOCK!

If the power cord is too short, never use

multiple outlets or extension cords. Instead,

please contact customer service.

Power outlet with

grounding conductor: 110 V ... 127 V / 60 Hz

Circuit breaker: min. 15 A ... 20 A

Appliance: 5.5 A

en-us Getting to know your appliance

14

*Getting to know your

appliance

Get t i ng to know your appl i anc e

Appliance

bottle

#

+

):

)B

)J

H

P

@

`

)2

)"

)*

X

0

h

(

8

# Refrigerator compartment

+ Freezer compartment

( Ice maker

0 Ice cube bin

8 Dispenser

@ Operating controls

H Water filter

P Interior light

X Rating plate

` Door pillar with condensation protection

h Partition with humidity controller

)" Vegetable bin

)* Storage compartment for large bottles

)2 Cold storage bin

): Frozen food bin (top)

)B Frozen food bin (large)

)J Height-adjustable feet

Getting to know your appliance en-us

15

Operating controls

Controls submenu

(08@ H P X `h)")*)2):

( Refrigerator compartment Û super button

Switches super cooling on or off.

0 Refrigerator compartment temperature

display

Indicates the set temperature in °C/°F.

8 Refrigerator compartment Y/X button

Sets the temperature of the refrigerator

compartment.

@ fresh button

Switches freshness mode on or off.

H eco button

Switches energy-saving mode on or off.

P vacation button

Switches vacation mode on or off.

X ÿ power button

Switches the appliance on or off.

` alarm off button

Switches off the alarm.

h menu button

Opens the menu.

)" change filter button

Switches the change filter alarm off.

)* Freezer compartment ¾ super button

Switches super freezing on or off.

)2 Freezer compartment temperature display

Indicates the set temperature in °C/°F.

): Freezer compartment Y/X button

Sets the temperature of the freezer

compartment.

P`hXH(0 @8

( Submenu display

Displays the selected submenu.

0 Y/X submenu button

Used to navigate through the submenu.

8 connect button

Opens the Home Connect menu.

@ light settings button

Opens the lighting menu.

H °C/°F button

Opens the temperature unit menu.

P Settings display

Displays the settings of the submenu.

X Y/X Settings button

Changes the settings of the submenu.

` alarm off button

Opens the alarm menu.

h change filter button

Opens the filter menu.

en-us Getting to know your appliance

16

Ice and water dispenser Equipment

Storage compartment

You can remove the storage compartment:

■ Lift up the storage compartment and remove.

Shelf

You can remove and adjust the shelf:

■ Lift shelf and remove.

Notes

■ Do not cover the ventilation openings.

■ Insert shelf carefully to avoid scratching the

appliance.

■ Ensure that the hooks are fully inserted and the

shelf is horizontal.

( lock button

Locks or unlocks the ice and water

dispenser.

0 light button

Switches the continuous light of the ice and

water dispenser on or off.

8 cubed button

Sets dispensing to ice cubes.

@ crushed button

Sets dispensing to crushed ice.

H water button

Sets dispensing to water.

P bottle fill button

Sets dispensing to a specific amount of

water.

X Water dispenser outlet

` Ice dispenser opening

h Dispenser lever

)" Drip tray

bottle

h

)"

`

X

H(0 @8P

Getting to know your appliance en-us

17

Vegetable bin

You can remove the bin:

■ Pull out the bin all the way, lift at the front and

remove.

You can insert the bin:

■ Pull out the telescopic rails all the way.

■ Place the bin on the telescopic rails and push into

the appliance until it engages.

Cold storage bin

You can remove the bin:

■ Pull out the bin all the way, lift at the front and

remove.

You can insert the bin:

■ Pull out the telescopic rails all the way.

■ Place the bin on the telescopic rails and push into

the appliance until it engages.

Frozen food bin (top)

9 CAUTION

DAMAGE TO EQUIPMENT

Never remove the partition wall from the bin.

You can remove the bin:

■ Pull out the bin all the way, lift at the front and

remove.

You can insert the bin:

■ Pull out the telescopic rails all the way.

■ Place the bin on the telescopic rails and push into

the appliance until it engages.

Frozen food bin (large)

9 CAUTION

DAMAGE TO EQUIPMENT

Never remove the partition wall from the bin.

You can take out the frozen food bin (large):

1. Pull the freezer compartment drawer all the way

out and remove the frozen food bin (top).

2. Lift the frozen food bin (large) and remove it.

en-us Getting to know your appliance

18

Ice maker

9 WARNING

RISK OF INJURY!

Never reach under or into the ice maker.

Notes

■ Ice cube production will start as soon as freezer

and refrigerator compartments reach the set

temperatures.

■ As soon as the appliance reaches the set

temperature, the first batch of ice cubes will be

ready in approximately 4 hours.

■ Once ready, the ice cubes are automatically

discharged into the ice cube bin.

■ Ice cube production stops automatically when the

ice cube bin is full.

■ For hygiene reasons, discard the ice cubes

produced within the first 24 hours.

Ice cube bin

9 WARNING

RISK OF INJURY!

Never reach into the dispenser opening of the

ice cube bin.

9 WARNING

RISK OF COLD BURNS!

Avoid prolonged contact between the skin and

ice or metal surfaces in the ice cube bin.

9 CAUTION

■ Damage to the appliance: Never store bottles or

food in the ice cube bin, even for short

periods. This may block and damage the ice

maker.

■ Damage to equipment: Never clean the ice cube

bin in the dishwasher.

■ When full, the ice cube bin is heavy: Pull the ice

cube bin out with both hands.

Notes

■ You can take large amounts of ice cubes directly

out of the ice cube bin or store them in the frozen

food bin (top).

■ Never put ice cubes into the ice cube bin

manually.

■ Clean the ice cube bin with lukewarm water and

wipe dry with a soft cloth so new ice cubes

cannot stick to it.

You can remove the ice cube bin:

■ Grasp the left and right-hand notch under the bin

and pull forward to remove.

You can insert the ice cube bin:

■ Position the bin in the opening and slide back

until it engages.

Notes

■ If the bin jams during insertion, remove any

excess ice from the opening.

■ During insertion, the turning position of the screw

conveyor on the bin and the opening must match

up.

■ If the bin cannot be inserted, rotate the screw

conveyor on the bin and try again.

Operating the appliance en-us

19

Water filter

Note: After installing a new water filter, for hygiene

reasons discard the ice cubes produced within the

first 24 hours and dispense water for 5 minutes and

discard.

The water filter supplied filters particles and the taste

of chlorine out of the water, not bacteria or microbes:

Replace the water filter

■ every 6 months

■ as soon as the change filter button lights up

■ if the water flow is visibly reduced

Note: A new water filter is available from our

customer service, your dealer or on our website.

If you use an external water filtration system, you can

also use the appliance without an internal water filter

To do this, replace the water filter with a bypass filter:

■ The bypass filter removes coarse particles from

the drinking water and can be cleaned as

required.

■ The bypass filter can remain in the appliance

permanently and does not need to be changed.

■ Switch off the change filter alarm as soon as the

change filter button lights up.

~ "Change filter alarm" on page 21

Note: A new bypass filter is available from our

customer service or on our website.

Change water filter or replace with bypass filter:

Notes

■ When changing, some water will drip from the

filter. Wipe drips up with a soft cloth.

■ You can dispose the used filter with your

household garbage.

1. Reach into the lower recess of the filter cover,

pull forwards slightly and move to the bottom left.

2. Turn the filter 90° counterclockwise and remove.

3. Insert the new filter in the filter opening to the

stop and turn 90° clockwise as far as it will go.

4. Move the filter cover up to the right again and

slide back as far as it will go.

1Operating the appliance

Oper at i ng the appl i ance

Switching the appliance on

1. Press ÿ power button.

The appliance begins to cool. The alarm off

button will blink and a warning sound will beep if

the temperature in the freezer compartment is still

too warm.

2. Press alarm off button.

The warning sound switches off.

3. Set the required temperature.

~ "Setting the temperature" on page 20

Operating tips

■ When the appliance has been switched on, it may

take several hours until the set temperatures have

been reached. Do not put in any food until the

selected temperature has been reached.

■ The fully automatic NoFrost system ensures that

the appliance remains frost-free. Defrosting is not

required.

■ The front sides of the housing are warmed to

prevent condensation in the area of the door seal.

Switching off and disconnecting the

appliance

Switching off the appliance

■ Press ÿ power button.

The appliance is no longer cooling.

Disconnecting the appliance

If you are not going to use the appliance for a long

period:

1. Interrupt the water supply to the appliance.

2. Take all food out of the appliance.

3. Press ÿ power button.

The appliance is no longer cooling.

4. Pull out the power plug or switch off the circuit

breaker.

5. Remove the water filter, empty the ice cube bin

and clean the appliance.

~ "Cleaning" on page 28

6. Leave the doors and drawers of the appliance

open.

Setting the temperature unit

You can choose between the units °C and °F:

1. Press menu button.

2. Press °C/°F button.

3. Press Y/X Settings button until settings display

shows °C or °F.

4. Press menu button.

The setting is saved.

en-us Operating the appliance

20

Setting the temperature

Recommended temperature

Cooling compartment

■ Keep pressing the Y/X button until the display

indicates the required temperature.

Freezer compartment

■ Keep pressing Y/X button until the display

indicates the required temperature.

Super cooling

Super cooling cools the refrigerator compartment as

cold as possible.

Switch on super cooling, e.g.:

■ Before placing large quantities of food into the

compartment

■ For cooling drinks quickly

Note: When super cooling is switched on, increased

operating noises may occur.

After approx. 6 hours, the appliance switches to

normal operation.

Switching super cooling on/off:

■ Press Û super button.

When super cooling is switched on, the button is

lit up.

Super freezing

With super freezing, the freezer compartment cools

down to the coldest temperature setting of the

freezer compartment.

Switch on super freezing, e.g.:

■ To quickly freeze food all the way to the center

■ To increase ice cube production

Note: When super freezing is switched on, increased

operating noise may occur.

After approx. 8 hours, the appliance automatically

returns to normal operation.

Switching super freezing on/off:

■ Press ¾ super button.

When super freezing is switched on, the button

lights up.

Energy saving mode

You can set the appliance to save energy with the

energy-saving mode.

The appliance automatically sets the following

temperatures:

■ Refrigerator compartment: 43 °F (6 °C)

■ Freezer compartment: 6 °F (–14 °C)

Switch energy-saving mode on or off:

■ Press eco button.

The temperatures are changed, and the display

shows the new temperatures. When energy-

saving mode is switched off, the last temperature

set is displayed.

Freshness mode

Food stays fresh for even longer with freshness

mode.

The appliance automatically sets the following

temperature:

■ Refrigerator compartment: 36 °F (2 °C)

The temperature in the freezer compartment remains

unchanged.

Switch freshness mode on or off:

■ Press fresh button.

The temperature is changed, and the display

shows the new temperature. When freshness

mode is switched off, the last temperature set is

displayed.

Vacation mode

If leaving the appliance for a long period, you can

switch it to energy-saving vacation mode.

The appliance automatically sets the following

temperature:

■ Refrigerator compartment: 43 °F (6 °C)

The temperature in the freezer compartment remains

unchanged.

Switch on vacation mode:

■ Press vacation button.

The temperature is changed and the display

shows the new temperature.

Empty the ice cube bin for hygiene reasons.

Switching off vacation mode:

■ Press vacation button.

The last temperature set is displayed.

For hygiene reasons, dispense water for

5 minutes and discard.

Refrigerator compartment: 37 °F (3 °C)

Freezer compartment: 0 °F (–18 °C)

La page est en cours de chargement...

Bosch B36CD50SNB/03 Le manuel du propriétaire

Bosch B36CD50SNB/03 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents