Barrett 4050IP Manuel utilisateur

Marque: Barrett

Modèle: 4050IP

Catégorie: Systèmes vidéo de voiture

Taper: Manuel utilisateur

Operating and Installation

Manual

Barrett 4050 HF SDR Transceiver

BCM40500/14.2

Model: 4050ip/4050se

iii

RF Exposure Warning

To ensure optimal transceiver performance and to avoid exposure to excessive

electromagnetic elds, the antenna system must be installed according to the

instructions provided.

High voltages exist on the antenna during transmission and tuning. Do not

touch the antenna during these activities. RF burns may result.

Install the grounding system or counterpoise as directed to prevent RF burns

from any metal part of the transceiver.

Safe working distance is based on continuous exposure to CW type transmis-

sions, for occupational and bystander exposure.

When the 4050 transceiver is used at a power level of 150 watts PEP and a 13

dBi gain antenna, the antenna(s) used with this Transceiver should be located at

least 13.6 metres from the operator and should not be co-located or operating

in conjunction with any other antenna or transmitter.

When the 4050 transceiver is used in a vehicular environment at a power level

of 150 watts PEP with 1.5 dBi gain antenna, the antenna(s) used with this

transceiver should be located at least 3.6 metres from the operator and should

not be co-located or operating in conjunction with any other antenna or trans-

mitter.

Approved antenna types and minimum separation dis-

tance:

Antenna type Gain

(dBi)

PEP

(W)

Minimum separation

distance (m)

Typical

Environ-

ment

Automatic tuned and whip 0 150 3.1 Vehicle

Magnetic Loop 1.5 150 3.6 Vehicle

Multi-wire Broadband 5 150 5.4 Fixed

Log-Periodic 13 150 13.6 Fixed

Automatic tuned and Whip 0 125 2.8 Vehicle

Magnetic Loop 1.5 125 3.3 Vehicle

Multi-wire Broadband 5 125 5.0 Fixed

Log-periodic 13 125 12.4 Fixed

Automatic tuned and Whip 030 1.5 Vehicle

Antenna type Gain

(dBi)

PEP

(W)

Minimum separation

distance (m)

Typical

Environ-

ment

Magnetic Loop 1.5 30 1.7 Vehicle

Multi-Wire Broadband 530 2.5 Fixed

Log-Period 13 30 6.1 Fixed

Automatic tuned and whip 0 10 0.8 Vehicle

Magnetic Loop 1.5 10 1.0 Vehicle

Multi-wire Broadband 5 10 1.4 Fixed

Log-Periodic 13 10 3.5 Fixed

It is important that the installer and operator maintain a minimum safe separa-

tion distance with the actual antenna used in the installation and to insure, in a

vehicular environment, that the transmitter is only used when persons outside

the vehicle are at least the recommended lateral distance away.

The image below shows an example of minimum recommended separation dis-

tance from antenna in a vehicular environment.

Note: References to Vehicular environments and minimum safe oper-

ating distances relate to persons outside the vehicle only and not to

persons within the vehicle.

FCC RF Exposure Compliance Statement

Supplier’s Declaration of Conformity

The Barrett 4050 transceivers have been evaluated and comply with the Federal

Communications Commission (FCC) RF exposure limits for the General Popula-

tion/Uncontrolled exposure environment.

In addition, the transceivers have been designed to comply with:

• US Federal Communications Commission Ofce of Engineering & Tech-

nology. Evaluating Compliance with FCC Guidelines for Human Exposure

to Radiofrequency Electromagnetic Fields OET Bulletin 65, Edition 97-01,

August 1997

Per FCC CFR 47 Part 2 Section 2.1007(a)

Responsible Party

Name: Barrett Communications

Address: 47 Discovery Dr, Bibra Lake, Western Australia, 6163

Phone Number: +618 9434 1700

Hereby declares that the product:

Model Name: 4050ip and 4050se

conforms to the following regulations:

FCC part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a)

____________________________________________________________________

Class A Digital Device

As a personal computer peripheral, this device complies with Part 15 of the FCC

rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

Notice:

This equipment has been tested and found to comply within the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

4050ip and 4050se models

FCC ID: OW4-4050IP

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment gener-

ates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

RF Energy Exposure and product Safety Guide for Mobile Two-Way Radios

This device complies with Part 15 of the FCC rules and Industry Canada’s RSS’s

per the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference

that may cause undesired operation.

• Changes or modications made to this device, not expressly approved by

Barrett Communications, could void the authority of the user to operate

this equipment.

Under Industry Canada regulations, this radio transmitter may only operate

using an antenna of a type and maximum (or lesser) gain approved for the

transmitter by Industry Canada. To reduce potential radio interference to other

users, this antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for suc-

cessful communication.

The operation of your Barrett Communications radio is subject to the Radio-

communicaitons Act and must comply with rules and regulations of the Federal

Government’s department of Industry Canada. Industry Canada requires that all

operators using Private Land Mobile Frequencies obtain a radio license before

operating their equipment.

Cet appareil est conforme à la partie 15 des règles de la FCC et aux ux RSS

d’Industrie Canada selon les conditions suivantes :

Important Safety Information

Notice to Users (FCC and Industry Canada)

CAUTION:

This radio is restricted to Occupational use only.

vii

• Cet appareil ne doit pas provoquer d’interférences nuisibles.

• Cet appareil doit accepter toute interférence reçue, y compris les

interférences susceptibles de provoquer un fonctionnement indésirable.

• Les changements ou modications apportés à cet appareil, non expressé-

ment approuvés par Barrett Communications, pourraient annuler le droit

de l’utilisateur à utiliser cet équipement.

Conformément aux réglementations d’Industrie Canada, cet émetteur radio ne

peut fonctionner qu’en utilisant une antenne d’un type et d’un gain maximum

(ou inférieur) approuvés pour l’émetteur par Industrie Canada. Pour réduire les

interférences radio potentielles avec d’autres utilisateurs, ce type d’antenne et

son gain doivent être choisis de telle sorte que la puissance isotrope rayonnée

équivalente (p.i.r.e.) ne soit pas supérieure à celle nécessaire pour une commu-

nication réussie.

Le fonctionnement de votre radio Barrett Communications est soumis à la Loi

sur les radiocommunications et doit être conforme aux règles et réglementa-

tions du ministère fédéral d’Industrie Canada. Industrie Canada exige que tous

les opérateurs utilisant des fréquences mobiles terrestres privées obtiennent

une licence radio avant d’utiliser leur équipement.

viii

Contents

INTRODUCTION 1 .......................................................................................... 1

Introduction ..................................................................................................2

Important Disclosure ............................................................................. 3

Terms & Abbreviations .......................................................................... 4

The Barrett 4050 HF Transceiver ....................................................................6

Transceiver Front .................................................................................. 6

Transceiver Rear - 4050ip ...................................................................... 7

Transceiver Rear - 4050se ...................................................................... 8

The 4050 Control Handset .................................................................... 9

Starting the Transceiver ...............................................................................11

Keypad ........................................................................................................11

Display ........................................................................................................12

Swipe Menu ........................................................................................ 13

BASIC OPERATION 2 .................................................................................. 15

Basic Conguration Diagram ....................................................................... 16

Antenna Type ..............................................................................................17

Selecting a Channel ..................................................................................... 18

Making a Voice Call .....................................................................................19

Making an Emergency Call ..........................................................................20

Receiving an Emergency Call .......................................................................21

SELCALL 3 .................................................................................................... 23

Overview .....................................................................................................24

Important Selective Calling Information ......................................................25

Summary of Calling Systems .......................................................................26

Setting up a Self ID .....................................................................................27

Setting up Contacts .....................................................................................28

Additional Contact Information .......................................................... 30

Making a Selcall ..........................................................................................31

Beacon Call ......................................................................................... 32

Selcall .................................................................................................. 33

Telcall .................................................................................................. 34

Advanced Call History ......................................................................... 37

Advanced Selcall Functions .........................................................................42

Selcall Settings .................................................................................... 42

Pagecall ............................................................................................... 43

GPS Request ........................................................................................ 44

GPS Position ........................................................................................ 46

Status Call ........................................................................................... 47

Secure Call .......................................................................................... 48

Hang-up Call ....................................................................................... 49

Selcall Networks .................................................................................. 50

BASIC SETTINGS 4 ...................................................................................... 53

System Information ..................................................................................... 54

General Settings ..........................................................................................56

Audio Settings .............................................................................................57

Display Settings ........................................................................................... 58

PROGRAMMING 5 ........................................................................................ 59

Channel Programming ................................................................................60

Programming Channels Through the Front Panel ................................ 60

Free Scroll Rx/Tx (VFO) .................................................................................64

Programming Via USB .................................................................................66

ADVANCED OPERATION 6 .......................................................................... 69

ARINC Call ...................................................................................................70

Audio - Advanced ........................................................................................71

Collective Call ..............................................................................................73

Digital Voice (Encoding) ..............................................................................74

Export .........................................................................................................75

Frequency Hopping .....................................................................................76

Selecting the Hopping Band................................................................ 76

Entering the Hopping PIN ................................................................... 76

Frequency Hop Rate ............................................................................ 76

Enabling and Disabling Hopping ......................................................... 76

GPS Push .....................................................................................................77

GPS Push State .................................................................................... 77

Privacy Key .......................................................................................... 77

Preamble Time .................................................................................... 77

Selcall Format...................................................................................... 77

Interval Time ....................................................................................... 78

UTC Offset Time .................................................................................. 78

GPS Push Channels.............................................................................. 78

IO Settings ..................................................................................................79

RS232 Connection ............................................................................... 79

RS232 Network Ports .......................................................................... 79

RS232 Network Encryption ................................................................. 79

RS232 Out (async. Indications) ............................................................ 79

RS232 Baud Rate ................................................................................. 80

External Alarm Type ............................................................................ 80

xii

Antenna Select Behavior ..................................................................... 80

Antenna 1 ........................................................................................... 80

Antenna 2 ........................................................................................... 81

Modes .........................................................................................................82

Mute ...........................................................................................................83

Network ......................................................................................................85

Noise Reduction (NR) ..................................................................................87

RF Settings ..................................................................................................88

Rx Preamp ........................................................................................... 88

Tx Over Beep ....................................................................................... 88

Tx Timeout .......................................................................................... 88

Noise Blanker ...................................................................................... 89

Tx Power Level .................................................................................... 89

AGC Hang ........................................................................................... 89

Broadcast Filter ................................................................................... 89

Scanning .....................................................................................................90

Scan Settings ...................................................................................... 91

Secure Display Mode ...................................................................................94

Security Settings ..........................................................................................95

Use OEM Selcall Privacy Key ................................................................ 96

OEM Selcall Privacy Key ....................................................................... 96

Frequency Hop PIN .............................................................................. 96

Frequency Hop Rate ............................................................................ 96

OEM Secure Type ................................................................................ 96

OEM Secure Key .................................................................................. 96

Secure Digital Voice/Data Key .............................................................. 97

Digital Voice Baud Rate ....................................................................... 97

Selcall Secure Call Hop Rate ................................................................ 97

xiii

Selcall Secure Call Code ...................................................................... 97

SDV/4026 Programming Mode ........................................................... 97

Service Mode ...................................................................................... 97

Enable Power On PIN .......................................................................... 98

Transceiver Lock .................................................................................. 98

Over the Air Zeroise (OTAZ) ................................................................. 98

Zeroise ................................................................................................ 98

Remote Access Password .................................................................... 98

Stealth Mode ...............................................................................................99

Theme Schedule ........................................................................................100

Tuning .......................................................................................................101

INSTALLATION 7 ........................................................................................ 103

Introduction ..............................................................................................104

Base Station Installations ..........................................................................105

Site Selection Recommendations ..................................................... 105

Cooling Fan ........................................................................................109

Antennas .................................................................................................. 110

912 Broadband Dipoles..................................................................... 110

4047 Automatic Tuning Horizontal Dipole Antenna .......................... 112

4045 Automatic Antenna Tuner for Base Station Installations .......... 115

Post-Installation Performance Test ..................................................... 117

411 Automatic Antenna Tuner for Base Station Installations ........... 120

Post-Installation Performance Test ..................................................... 121

Mobile Installations ...................................................................................125

Mobile Pack ...................................................................................... 125

4049 Automatic Tuning Mobile HF Antenna ..................................... 132

Installing a Secondary Control Head ..........................................................144

xiv

APPENDICES 8 ........................................................................................... 145

Appendix 1 - Specications .......................................................................146

Appendix 2 - Connectors ........................................................................... 149

Appendix 3 - Overview of HF Operation ....................................................154

Appendix 4 - BITE Test ..............................................................................158

Warranty Statement ..................................................................................161

Contact Details .................................................................................. 162

INTRODUCTION 1

This chapter contains the following sections:

• Introduction

• The Barrett 4050 HF Transceiver

• Starting the Transceiver

• Display

BARRETT 4050 HF SDR TRANSCEIVER - INTRODUCTION

Introduction

The Barrett 4050 Transceiver is an SDR based HF SSB transceiver with a fre-

quency range of 1.5 to 30 MHz in transmit and 250kHz -30MHz in receive. The

Barrett 4050 is designed using the latest technology enabling a physically small

package with a full feature complement.

Designed to operate in the most arduous environments, as encountered in off-

road vehicles, vessels and aircraft, the Barrett 4050 will provide many years of

efcient and trouble free service.

The Barrett 4050 supports features such as Selective Call (Selcall), direct dial

telephone connection to base stations tted with telephone interconnect sys-

tems (Telcall), GPS location, 2G and 3G ALE (Automatic Link Establishment), fre-

quency hopping, digital voice, data transmission and remote diagnostics. These

features make the Barrett 4050 HF Transceiver one of the most economical and

versatile HF transceivers available today.

The Barrett 4050 Transceiver caters for increased use of HF data transmission for

Internet email access and point-to-point data applications, by providing a com-

prehensive data modem interface port, high speed transmit-to-receive switch-

ing, a high stability frequency standard and an efcient cooling system option.

The Barrett 4050 Transceiver can be operated in either a local (desktop) con-

guration for base station applications or, with the addition of an inexpensive

mobile pack, in a remote control (trunk mount) conguration for mobile appli-

cations.

The Barrett 4050 Transceiver can be controlled from all major mobile and desk-

top platforms. Full remote control is available via the Barrett 4050 Remote Con-

trol app, providing unprecedented access to all transceiver functionality across

all major platforms.

Operated from 12 V DC to 24 V DC power supplies, the transmitter is rated

at 125-150 watt PEP in voice mode and is protected from over-voltage or

reverse-voltage application.

Up to 1000 channels (depending on the 4050 variant) are available. Auxiliary

features such as Selcall, Telcall, scanning, mute status, alarm system etc. can

be individually enabled or disabled for every channel as required to suit your

operation.

Teamed with other complementary Barrett products which include antennas,

power supplies, vehicle tracking packages and HF modems, the Barrett 4050 HF

Transceiver becomes a powerful tool, providing solutions to many long distance

communication requirements.

BARRETT 4050 HF SDR TRANSCEIVER - INTRODUCTION

Please refer to the 4000 Series IP Connectivity/Networking Guide (P/N

BCM40507) for information regarding IP connectivity and networking of the

4050 Transceiver.

Important Disclosure

Please note that this manual describes all the features of the

4050 HF SDR Transceiver and that some variants of the 4050

may not have all the features installed.

Illustrations may show accessories, optional equipment or

other features which are not part of the standard specica-

tion and are not available in some countries.

BARRETT 4050 HF SDR TRANSCEIVER - INTRODUCTION

Terms & Abbreviations

Term /

Abbreviation

Denition

ALE Automatic Link Establishment

AM Amplitude Modulation

ARINC A set of standards as established by Aeronautical Radio,

Incorporated (ARINC).

CCIR One of many possible Selcall formats as dened by the

Consultative Committee on International Radio (CCIR).

CF Custom Filter selection

CW Continuous Wave (used for Morse code)

dB Decibels

dBm Power ratio in decibels (dB) of the measured power refer-

enced to one milliwatt (mW).

DSP Digital Signal Processing

ESU Encryption Synchronisation Unit

FHSS Frequency Hopping Spread Spectrum

GPS Global Positioning System

HF High Frequency

INT International Selcall format

IP Internet Protocol

ISB Independant Sideband

LSB Lower Sideband

LUF Lowest Usable Frequency

MUF Maximum Usable Frequency

OEM Original Equipment Manufacturer, OEM Selcall Format

OTG On-The-Go (USB)

PCB Printed Circuit Board

PEP Peak Envelope Power

PIN Personal Identication Number

PSTN Public Switched Telephone Network

PTT Push to talk

BARRETT 4050 HF SDR TRANSCEIVER - INTRODUCTION

Term /

Abbreviation

Denition

Receive Only

Channel

A channel that receives only and cannot be transmitted

on.

Revertive Tone /

Signal

An acknowledgment signal automatically transmitted

from a station receiving a Selcall.

RF Radio Frequency

RFDS Royal Flying Doctor Service

Scan Table A list of channels used when scanning for incoming

calls.

Selcall Selective Calls

SCF Suppressed Carrier Frequency

SSL Signal Strength Level

Station ID The ID of the station being called (the receiving station’s

Self ID).

SE Standard Edition

Self ID The programmed address identication number of a local

station. (Used by other stations to call you.)

SMS Short Message Service

SSB Single Sideband (a transmission format)

Telcall Telephone call using the Selective Call protocol.

USB Upper Sideband

VSWR Voltage Standing Wave Ratio

BARRETT 4050 HF SDR TRANSCEIVER - INTRODUCTION

The Barrett 4050 HF Transceiver

Transceiver Front

Power button which combines switching the transceiver on and off

with adjusting the volume.

This will be represented as throughout the manual

2USB / WiFi Socket

3Touchscreen

Keypad

5Microphone socket

1 2 3 4

La page est en cours de chargement...

Barrett 4050IP Manuel utilisateur

Marque: Barrett

Modèle: 4050IP

Catégorie: Systèmes vidéo de voiture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Barrett 4050IP User manual

Barrett 4050IP Manuel utilisateur

Barrett 4050IP Manuel utilisateur

dans d''autres langues

Autres documents