TP-LINK tp-link Tapo D100C Tapo Smart Video Doorbell Wired Mode d'emploi

Marque: TP-LINK

Modèle: tp-link Tapo D100C Tapo Smart Video Doorbell Wired

Taper: Mode d'emploi

*Images may dier from your actual product.

Tapo Smart Video Doorbell Wired

Quick Start Guide

Before You Start

Tapo

WARNING: Risk of Electric Shocks

• Ensure that your existing doorbell works by ringing the

doorbell.

• Locate your existing doorbell chime.

• Make sure the doorbell is in an area with a strong Wi-Fi signal.

• Disconnect power at the fuse or circuit breaker before

installing.

• You can always nd detailed wiring and installation instructions

in the Tapo app.

Take care to avoid electric shocks.

*Recommended Installation Height: 1.2 m (4 ft) above the ground

Option 2. Mount to the wall

Install Your Doorbell

03 /

Flip the page over to complete setup.

1. Remove your existing doorbell on the door. Disconnect the

wires.

2. (Optional) Select the mounting wedge to adjust the viewing

angle of the doorbell.

Preparations for Installing Your Doorbell

02 /

Without Mounting Wedge

Without

Mounting Wedge

With Vertical

Mounting Wedge

With Horizontal Mounting Wedge

15°

5°

Take care to avoid electric shocks.

01 / Install Jumper Wire for Your Existing Chime

1. Turn o the circuit breaker. Make sure the power is o by

ringing your doorbell a few times.

OFF

Take care to avoid electric shocks.

2. Remove the chime cover and take a photo of the wiring in

case you want to reconnect it.

Note: If your doorbell chime has dierent markings, refer to instructions in

the Tapo app or consult a licensed electrician.

3. Slightly loosen the screws for the Front and Trans of your

front doorbell or the Rear and Trans of your rear doorbell,

then insert the jumper wire.

4. Tighten the screws and replace the chime cover.

Option 1. Stick to a clean wall

*This equipment shall be installed at a height of fewer than 2 meters.

1. Attach the included adhesive to the back of the bracket or the

wedge you have selected. If you use the wedge, ax the

bracket and the wedge with screws.

4. Mount the doorbell to the bracket and turn on the circuit

breaker.

3. Connect the wires to the two terminals at the back of the

doorbell, and tighten the terminal screws.

2. Route the wires through the bracket. Stick the bracket with

adhesive to a clean wall.

Note: This is applicable with tile, glass, marble, metal, stainless steel, and

hard wall surfaces.

Note: If the wires are too short, use the included extension wires and wire

nuts to make them longer.

If the wires are too short:

WedgeAdhesiveAdhesive

1. Route the wires through the mounting template and stick the

template. Drill two holes where indicated.

Φ=6 mm (15/64 in.)

Note: When mounting to uneven walls, stick the foam pad on the back of

the bracket or wedge.

2. Route the wires through the bracket. Insert two anchors into

the holes and use the screws to ax the bracket over the

anchors.

3. Connect the wires to the two terminals at the back of the

doorbell, then tighten the terminal screws.

4. Mount the doorbell to the bracket and turn on the circuit

breaker.

Note: If the wires are too short, use the included extension wires and wire

nuts to make them longer.

Wedge

(Optional)

Foam Pad

(Optional)

Front Doorbell

TRANS TRANSREARFRONT

Rear Doorbell

Tapo D100C & Tapo D130

04 / Set Up Your Doorbell and Chime

1. Download the Tapo app from the App Store or Google Play.

Open the app and log in with your TP-Link ID. If you don't have

an account, create one rst.

Doorbell Appearance

Doorbell Slot & Button Explanation Chime Button Explanation

Chime Appearance

Press to adjust the volume of the ring.

Volume Button

Press to cycle through dierent ringtones.

Music Button

Reset Button

Ring Button

Lens

LED

microSD Card Slot

Loosen the screws and insert a microSD card for local recording.

*microSD card not included.

Reset Button

• Press and hold for 5 seconds: Reset Wi-Fi settings

• Press and hold for 10 seconds: Reset to factory settings

• Use a pin to press and hold for 5 seconds: Reset Wi-Fi settings

• Use a pin to press and hold for 10 seconds: Reset to factory settings

Microphone

Reset Button

LED

Speaker

5 5

4 4

2. Tap the button in the app and select your model. Follow

the instructions in the Tapo app to set up your doorbell. Then

plug in your chime and pair with the doorbell.

Doorbell LED Indication

Blinking red and green

Blinking red slowly

Solid white

Blinking red quickly

Solid red

Blinking green quickly

Solid amber

Starting up

Connected to the cloud

Ready for setup

Connecting to Wi-Fi

Connected to Wi-Fi

Doorbell resetting

Doorbell updating

Blinking red and green

Blinking red slowly

Solid green

Blinking red quickly

Solid red

Blinking green quickly

Solid amber

Starting up

Connected to the cloud

Ready for setup

Connecting to Wi-Fi

Connected to Wi-Fi

Chime resetting

Chime updating

Chime LED Indication

How to Detach Doorbell

Use the doorbell detaching pin provided if you wish to detach

the doorbell from the mounting bracket.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment o and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also

complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with

provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other

antenna or transmitter. End-users and installers must be provided with antenna installation instructions and

consider removing the no-collocation statement.

Caution!

Any changes or modications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non

contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de

rayonnement et votre corps.

CAN ICES-3 (B)/NMB-3(B)

Safety Information

• Do not use the device where wireless devices are not allowed.

• Keep the device away from re or hot environments. DO NOT immerse in water or any

other liquid.

• Do not disassemble, repair or modify the product.

• Do not use the product if the casing has been broken. Danger of electric shock.

• Never touch the product with wet hands.

• Do not place near automatically controlled devices such as re alarms. Radio waves

emitted from this product may cause such devices to malfunction resulting in an accident.

• Observe restrictions on using wireless products in fuel depots, chemical plants or when

blasting operations are in progress.

• Do not use liquid to clean the product. Only use a dry cloth.

• Never put metal objects inside the product. If a metal object enters the product turn o

the circuit breaker and contact an authorised electrician.

• This product is not intended to be used when providing medical care. Consult the

manufacturer of any personal medical devices, such as pacemakers or hearing aids to

determine if they are adequality shielded from external RF (radio frequency) energy.

• Do not use this product in health care facilities. Hospitals or health care facilities may be

using equipment that could be sensitive to external RF energy.

• Do not use this product near water for example near a bath tub, wash bowl, kitchen sink or

laundry tub, in a wet basement or near a swimming pool.

• The product should be kept free from excessive smoke, dust or high temperature and

vibration.

• This product should not be exposed to direct sunlight

• Do not place heavy objects on top of the product.

• This product may interfere with other electronic products such as TV, radios, personal

computers, phones or other wireless devices.

• This equipment can be powered only by equipment that complies with Power Source

Class 2 ( PS2) or Limited Power Source(LPS) dened in the standard of IEC 62368-1.

• Doorbell Operating Temperature: -20 °C ~ 45°C (-4°F ~ 113°F)

• Chime Operating Temperature: 0 °C ~ 40°C (32°F ~ 104°F)

Please read and follow the above safety information when operating the device. We cannot

guarantee that no accidents or damage will occur due to improper use of the device.

Please use this product with care and operate at your own risk.

TP-Link hereby declares that the device is in compliance with the essential requirements

and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and

(EU)2015/863.

The original EU declaration of conformity may be found at

https://www.tapo.com/support/ce/

TP-Link hereby declares that the device is in compliance with the essential requirements

and other relevant provisions of the Radio Equipment Regulations 2017.

The original UK declaration of conformity may be found at

https://www.tapo.com/support/ukca/

Need some help?

Visit https://www.tapo.com/support/

for technical support, the user guide, FAQs,

warranty & more

microSD

TP-LINK tp-link Tapo D100C Tapo Smart Video Doorbell Wired Mode d'emploi

Marque: TP-LINK

Modèle: tp-link Tapo D100C Tapo Smart Video Doorbell Wired

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: TP-LINK tp-link Tapo D100C Tapo Smart Video Doorbell Wired User guide

TP-LINK tp-link Tapo D100C Tapo Smart Video Doorbell Wired Mode d'emploi

TP-LINK tp-link Tapo D100C Tapo Smart Video Doorbell Wired Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents