Maytag MGD6400TB - Bravos Gas Dryer Mode d'emploi

Marque: Maytag

Modèle: MGD6400TB - Bravos Gas Dryer

Catégorie: Sèche-linge électriques

Taper: Mode d'emploi

BRAVOS TMFABRIC CARE SYSTEM GAS DRYER

USE & CARE GUIDE

SECADORA A GAS BRAVOS TMCON

DE CUIDADO DE TELAS

MANUAL DE USO Y CUIDADO

SISTEMA

SECHEUSE A GAZ BRAVOS TMAVEC SYSTEME

DE SOIN DES TISSUS

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALL: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

SI TIENE PREGUNTAS RESPECT() A LAS CARACTERiSTICA8,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVICIO TI_CNICO, LLAME AL: 1.800.688.9900

O VISITE NUESTRO SITIO WEB EN

WWW.MAYTAG.COM

AU CANADA, POUR ASSISTANCE, INSTALLATION OU SERVICE,

COMPOSER LE : 1.800.807.6777

OU VISITEZ NOTRE SITE {NTERNET _,

WWW.MAYTAG.CA

W10088778A

®*TABLE OF CONTENTS @*

DRYER SAFETY ..................................................................... 3

INSTALLATION INSTRUCTIONS ........................................ 5

TOOI.S AND PARTS .......................................................... 5

LOCATION REQUIREMENTS ........................................... 5

EI.ECTRICAL REQUIREMENTS ........................................... 7

GAS SUPPI Y REQUIREMENTS .......................................... 7

VENTING REQUIREMENTS ............................................... 9

PI.AN VENT SYSTEM ....................................................... 10

INSFAH. VENT SYSTEM ................................................... 11

INSFAH. I.EVEHNG LEGS ................................................ 12

MAKE GAS CON NECTION ............................................. 12

CONNECT VENT ............................................................. 13

LEVEl. [DRYER................................................................... 13

REVERSE DOOR SWING ................................................. 13

COMPI.ETE INSTAl I ATION ............................................ 15

DRYER USE ......................................................................... 16

STAR[ING YOUR [DRYER................................................ 16

STOPPING, PAUSING OR RESTARTING ........................ 17

DRYING AND CYCI.E TIPS .............................................. 17

STATUS HGHTS .............................................................. 18

CYCI.ES ............................................................................ 18

MODIFIERS ...................................................................... 19

OPTIONS ......................................................................... 20

END OF CYCI.E SIGNAl ................................................... 20

CHANGING CYCI.ES, MODIFIERS AND OPTIONS ........ 20

DRYING RACK OPTION ................................................. 21

DRYER CARE ...................................................................... 22

CI.EANING THE [DRYER I.OCATION ............................... 22

CLEANING THE LINT SCREEN ........................................ 22

CI.EANING THE [DRYER INTERIOR ................................. 23

REMOVING ACCUMUI.ATED I.INT ................................ 23

VACATION AND MOVING CARE .................................. 23

CHANGING THE DRUM I.IGHT ..................................... 23

TROUBLESHOOTING ........................................................ 24

ASSISTANCE OR SERVICE .................................................. 26

WARRANTY ....................................................................... 27

INDICE

SEGURIDAD DE LA SECADORA ....................................... 28

INSTRUCCIONES DE INSTALACION ............................... 30

HERRAMIENTAS Y PIEZAS .............................................. 30

REQUISITOS [DE UBICACION ....................................... 30

REQUISITOS EI.ECTRICOS .............................................. 32

REQUISITOS DEI. SUMINISTRO DE GAS ....................... 33

REQUISITOS [DEVENTI[ ACION ..................................... 34

PLANIFICACI(£_N DE[ SISFEMA DE VENTII.ACI('£_N ....... 35

INSTALACION [)El. SISTEMA DE VENTHACION ........... 37

INSTAI.ACION DE LAS PATAS NIVEI.ADORAS .............. 37

CONEXION DEI. SUMINISFRO DE GAS ........................ 38

CONEXION DEL DUCFO [DE ESCAPE ............................ 38

NIVELACI(_DN DE LA SECADORA ................................... 38

COMO INVERTIR El CIERRE DE LA PUERTA ................. 39

COMPI.ETE IA INSTAI.ACION ........................................ 41

USO DE LA SECADORA .................................................... 41

PUESTA EN MARCHA [DELA SECADORA ..................... 42

COMO DETENER, PAUSAR Y VOLVER A PONER

EN MARCHA ................................................................... 43

SUGERENCIAS DE CICLOS Y SECADO .......................... 43

IUCES [DE ESTADO ......................................................... 44

CICLOS ........................................................................... 44

MODIFICADORES .......................................................... 45

OPCIONES ...................................................................... 46

SENAI. [DE FIN DE CICI.O (END OF CYCLE SIGNAL) ..... 46

CAMB]O DE CICI.OS, MODIFICADORES Y

OPCIONES ...................................................................... 47

OPCIC)N DE ESFANTE DE SECADO ............................... 47

CUIDADO DE LA SECADORA .......................................... 48

LIMPIEZA DEE LUGAR DONDE ESFA I.A SECADORA... 48

LIMPIEZA DEI. FILTRO DE PEI.USA ................................ 48

LIMPIEZA DEI. INTERIOR DE LA SECADORA ................ 49

EHMINACIC)N DE PELUSA ACUMULADA .................... 49

CUIDADO DURANTE I.AS VACACIONES Y

MUDANZAS ................................................................... 49

CAMB]O DE LA LUZ DEE TAMBOR ............................... 49

SOLUClON DE PROBLEMAS ............................................ 50

AYUDA O SERVICIO Tf_CNICO ........................................ 52

GARANTiA ........................................................................ 53

TABLE DES MATIERES

Sf_CURITI_DE LA Sf_CHEUSE .............................................. 54

INSTRUCTIONS D'I NSTALLATION .................................. 56

OUII[ I.AGE ET PIECES .................................................... 56

EXIGENCES D'EMPI.ACEMENT. ...................................... 56

SPECIFICATIONS I_LECTRIQUES ..................................... 58

AI.IMENTATION EN GAZ ................................................ 59

EXIGENCES CONCERNANT UEVACUATION ................ 60

PI.ANIFICATION DU SYSTEME D'EVACUATION ........... 61

INSTALI.ATION DU SYSTEME D'EVACUATION ............ 63

INSTAI.EATION [DES PIEDS DE NIVEIZEMENT. .............. 63

RACCORDEMENT AU GAZ ............................................ 63

RACCORDEMENT DU CONDUIT D'EVACUATION ...... 64

REG[ AGE [DE UAPLOMB [DE I.A SECHEUSE ................... 64

INVERSION DU SENS D'OUVERTURE [DE I.A PORTE....64

ACHEVER I/INSTAIJ.ATION ........................................... 66

UTILISATION DE LA SECHEUSE ....................................... 67

MISE EN MARCHE DE LA SECHEUSE ............................. 68

ARRET, PAUSE OU REMISE EN MARCHE ....................... 69

CONSEHS POUR I.E SECHAGE ET I.ES

PROGRAMMES ............................................................... 69

TEMOINS LUMINEUX ..................................................... 70

PROGRAMMES ............................................................... 70

MODIFICATEURS ............................................................ 71

OPTIONS ......................................................................... 72

SIGNAl. [DE FIN DE PROGRAMME ................................. 72

CHANGEMENT DES PROGRAMMES,

MODIFICATEURS ET OPTIONS ...................................... 73

OPTION DE GRILl E [DE SI_CHAGE ................................. 73

ENTRETIEN DE LA SI_CHEUSE ........................................... 74

NETTOYAGE [DE UEMPI.ACEMENT [DE [.A

SECHEUSE ....................................................................... 74

NETTOYAGE DU FII.TRE _, CHARPIE ............................. 74

NETTOYAGE DE L'IN-I [_RIEUR DE I.A SECHEUSE ........... 75

RETRAIT DE LA CHARPIE ACCUMUI.EE ......................... 75

PRECAUFIONS A PRENDRE POUR LES

VACANCES ET AVANT UN DEMENAGEMENT .............. 75

CHANGEMENT [DE I/AMPOULE D'ECLAIRAGE

DU TAMBOUR ................................................................ 75

Df_PANNAGE ..................................................................... 76

ASSISTANCE OU SERVICE ................................................. 78

GARANTIE ......................................................................... 79

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

I WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

@ INSTALLATION INSTRUCTIONS @

TOOLS AND PARTS

Gather the required tools and parts before starting installation. Read and follow the

instructions provided with ally tools listed here.

8" or 10" pipe wrench • Y4" nut driver or socket

wrench

8" or 10" adjustable

wrench (for gas • Knife

connections/

• Vent clamps

Flat-blade screwdriver

• Pipe-joint compound

Adjustable wrench that resistant to [P gas

opens to 1"/2.5 cm) or

hex-head socket wrench • Caulking gun and

compound (for installing

(for adjusting dryer feet) new exhaust vent)

]eve I

• Pliers

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

4 leveling legs

Parts needed:

Check local codes and ronsuh gas supplier. Check existing gas supply, electrical supply and

venting, and read "Electrical Requirements," "Gas Supply Requirements" and "Venting

Requirements" before purchasing parts.

Mobile home installations require special parts (listed following) that may be ordered by

calling the dealer from whom you purchased your dryer. For information on ordering, please

refer to the "Assistance or Service" section of this manual. You may also contact the dealer

from whom you purchased your dryer.

• Mobile home installation kit. Ask for Part Number _¢46764.

• Metal exhaust system hardware.

LOCATION REQUIREMENTS

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate _¢0-amp circuit.

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See

"Electrical Requirements."

• A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The

combined weight of a companion appliance should also be considered.

• A level floor with a maximum slope of 1" (2.5 cm) under entire dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer

might not shut off at the end of an automatic cycle. Drying times can be extended.

[he dryer must not be installed or stored in an area where it will be exposed to water and/or

weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in

garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

{'I

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested

for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be

considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

• For closet installation, with a door, minimum ventilation openings in the top and bottom

of the door are required. I ouvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Additional spacing is required if you exhaust out the rear of the dryer to either the right or

left side.

olo

(45.7cm)

1_14 m_?

48in?*

(310cm2)- "_"

24in.2.

(15S_m_)- -I_1.

1"_l I_- 29"_ _-1" _11"*1_29,_"_1_",-

(2.5era) (73.7cm) (2.5cm) (2.5era)(74.3era)(12.7era)

A B

A. Recessed at_'a

B. 5ide view - closet or confined area

C. Closet door with vents

3,,_

__ 3"*

(7.6cm)

*Required spacing

Mobile home - Additional installation requirements

[his dryer is suitable for mobile home installations. The installation must conform to the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or

Standard CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for purchase from your dealer.

• Mobile home Installation Kit Part Number 346764. See "[bols and Parts" section for

information on ordering.

• Special provisions must be made in mobile homes to introduce outside air into the dryer.

The opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

ELECTRICAL REQU IREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire_ or electrical shock.

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay

fuse or circuit breaker is recommended. [t is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING iNSTRUCTiONS

• For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS SUPPLY REQUIREMENTS

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut-off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Gas Type

Natural Gas:

This dryer is equipped for use with Natural gas. [t is design-certified by CSA International for

I.P/propane or butane) gases with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in your home. Burner

information is located on the rating plate in the door well of your dryer. Ifthis information

does not agree with the type of gas available, contact your dealer or call the phone

numbers referenced on the front page of this manual.

[P gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial

rating plate for use with a different gas without consulting your gas company. For information

on ordering an [.P conversion kit, please refer to the "Assistance or Service" section of this

manual. Ask for Part Number 49572.

Gas Supply Line:

• Must include 1/8" NPT minimum plugged tapping accessible for test gauge connection,

immediately upstream of the gas connection to the dryer (see illustration).

• 1/2" IPS pipe is recommended.

• 3/8"approved aluminum or copper tubing is acceptable for lengths under 20 ff (6.1 m) if

local codes and gas supplier permit.

• If you are using Natural gas, do not use copper tubing.

• %" flare x %" NPT adapter fitting between dryer pipe and %" approved tubing.

• Lengths over 20 fl (6.1 m) should use larger tubing and a different size adapter fitting.

• If your dryer has been converted to use [.P gas, %" I.P compatible copper tubing can be

used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of IP gas must be used. Do not use

TEFI.ON '_tape.

• Must include a shutoff valve:

In the U.S.A.:

An individual manual shutoff w_lve must be installed within six (6) feet (1.8 m) of the dryer

in accordance with the National Fuel Gas Code, ANSI Z223.1.

In Canada:

An individual manual shutoff valve must be installed in accordance with the B149.1,

Natural Gas and Propane Installation Code. It is recommended that an individual manual

shutoff valve be installed within six (6) feet (1.8 m) of the dryer. The location should be

easy to reach for opening and closing.

A C E

B D

A. _" flexible gas connector

B. _" pipe to flare" adapter flttitlg

C. _" NP7 minimum plugged tapping

D. _/_" NPTgas supply line

E. Gas shutoff valve

Gas supply connection requirements

• Use an elbow and a %" flare x %" NPT adapter fitting between the flexible gas connector

and the dryer gas pipe, as needed to avoid kinking.

• Use only pipe-joint compound. Do not use TEFI.ON '_ttape.

• This dryer must be connected to the gas supply line with a listed flexible gas connector

that complies with the standard for connectors for gas appliances, ANSI Z21.24 or

CSA 6.10.

Burner Input Requirements:

Elevations above 10,000 ft (3,048 m):

• When installed above 10,000 ft (3,048 r'n) a 4% reduction of the burner Btu rating shown

on the model/serial number plate is required for each ,000 ft (_¢05 m) increase in

elevation.

Gas Supply Pressure Testing

• ]he dryer must be disconnected from the gas supply piping system during pressure testing

at pressures greater than _/Jpsi.

Dryer Gas Pipe

]he gas pipe that comes out through the rear of your dryer has a %" male pipe thread.

(1.9 cm)

A. 3/8" NPT dry_,rpip_"

t®TEFLON is a legistered trademark of E.I. Du Pont De Nenlours and Company.

VENTING REQUI REMENTS

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: lb reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a

concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged

with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final

location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in

reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45 ° elbows provide better airflow than 90 ° elbows.

Clamps

Good Better

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws or other fastening devices

that extend into the interior of the duct. Do not use duct tape.

Clamp

s ,

4" ( 10.2 cm) heavy metal exhau:t _ent

Vent products can be purchased from your dealer or by calling Maytag Services. For more

information, see the "Assistance or Service" section of this manuah

Exhaust

Recommendedhoodstylesareshownhere.

(10.2 cm)

A. Louv_'re'd hood style"

B.Box hood styM

[he angled hood style {shown here) is acceptable.

(10.2 cm)_(_

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in

the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• L)o not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

PLAN VENT SYSTEM

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of tile dryer.

A. Dryer

8. Elbow

C. Wall

D. Fxhaust hood

E. Clamps

I. Rigid metal or flr,xible metal vent

G. V_'nt I_'ngth necessary to connect elbows

H. f xhaust outlet

Standard exhaust installation with rigid metal or flexible metal vent

Alternateinstallationsfor close clearances

Venting systems come ill many varieties. Select the type best for your installation, Two close-

clearance installations are shown. Refer to the manufacturer's instructions.

_: --I "__'

A B

A. Over-the-top installation tako available with one offset elbow)

B.Periscope installation

C. Rear exhaust installation to left or right side

NOTE: [he following kits for close clearance alternate installations are available for purchase.

Please see the "Assistance or Service" section of this manual to order.

• Over-the-ibp Installation:

Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch

• Rear exhaust installation to left or right side:

Part Number 8212504

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home

structure and must not terminate beneath the mobile home. [erminate the exhaust vent

outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the following Vent system chart to determine type of vent material and hood

combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust _[

systems longer than those specified wilh

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying

performance.

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is equiw_lent to adding one

elbow. To determine maximum exhaust length, add one elbow to the chart.

Number of 90 ° turns Type of vent Box or Louvered Angled hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

.....i............................................................................. ............................T: Zmi....................

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

..............................................................................................................................................................................................................................

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft 15.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft 17 m) 15 ft (4.6 m)

INSTALL VENT SYSTEM

1. Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust

hood with 4" (10.2 cm) clamp.

3. Runventtodryerlocation.Usethestraightestpathpossible.See"Determineventpath"in

"PlanVentSystem."Avoid90°turns.Useclampstosealalljoints.Donotuseducttape,

screwsorotherfasteningdevicesthatextendintotheinterioroftheventtosecurevent.

INSTALL LEVELING LEGS

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. lb protect the floor, use a large flat piece of cardboard from the dryer carton. Place

cardboard under the entire back edge of the dryer.

2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on

the cardboard. See illustration.

Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the

diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to tile floor.

Mobile home installations require a Mobile Home Installation Kit. See "lools and Parts"

section for information on ordering.

MAKE GAS CONNECTION

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound

on the threads of all non-flared male fittings. If flexible metal tubing is used, lye sure there

are no kinks.

A. Hare'd male thread

B. Non-flared male thread

NOTE: For [.P gas connections, you must use pipe-joint compound resistant to the action

of [P gas. Do not use TEFLON _÷*tape.

A combination of pipe fittings must be used to connect the dryer to the existing gas line.

Shown is a recommended connection. Your connection may lye different, according to the

supfyly line type, size and location.

A. _" flexible gas connector

B. _" dryer pipe

C. _" to _" pipe elbow

D. _" pipe-to-flare" adapter fitting

Open the shutoff valve in the supply line. The valve is open when the handle is parallel to

the gas pipe.

A. Closed valve

B. Open valve

|est all connections by brushing on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leak found.

€¢_)TEFLON is a legistered trademark of E.I. Du Pont De Nemours and Company.

CONNECT VENT

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to

existing vent, make sure the vent is clean. ]-he dryer vent must fit over the dryer exhaust

outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a

4" (102 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

LEVEL DRYER

Check the levelness of the dryer by first placing a level on the top of the dryer near the

console.

Then, by placing a level in the crease on the side of the dryer between the top of the dryer and

the dryer cabinet, check the levelness from front to back.

REVERSE DOOR SWING

You can change your door swing from a right-side opening to a left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1. Open the dryer door.

2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front

panel of the dryer.

3. I.oosen the top screw from each of the 2 hinges in Step 2.

A. Loosen these screws.

B. R@mov_! th@8_! scr(!w8.

Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a

flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose

screws from dryer front panel.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs

up or down and check again for levelness.

5. Removethe4plasticplugslocatedoutsidethedryerdooropening.

6. Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in

Step 4.

Reverse the strike

1. Remove the door strike from the dryer door opening.

2. Remove the cosmetic screw opposite the door strike.

A. Door strike 4.

B.Cosmetic screw

Reinstall the door strike and cosmetic screw on the opposite side of the dryer door

opening from where they were removed.

NOTE: Door strike and plugs must be on the same side of the dryer door opening.

Reinstall the door

1. Remove the 4 screws and 2 hinges from the dryer door.

2. Replace the 4 screws ill the same holes.

3. Remove the 4 screws from the opposite side of the door.

..a

Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side

to attach the hinge to the front paneh

14-

Installscrewsillthetophingeholesillthedoor.Donottightenscrews,leave

approximately_/2'/5mm)ofscrewexposed.

A. Install these scr_'ws first.

Hang door by placing screw heads into top slotted holes of hinges and slide door down.

Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge

screws.

7. Close door to engage door strike.

COMPLETE INSTALLATION

1. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check that the dryer is level. See "level Dryer."

Electrical Shook Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these inatruetiona can reault in death,

fire, or electrical shock.

6. Plug into a grounded 3 prong outlet. Turn on power.

7. Remove any protective film or tape remaining on the dryer.

NOTE: Glass door models have a protective film on the window that should be removed.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10. lest dryer operation by selecting a rimed Dry heated cycle and starting the dryer. For this

test, do not select the Air Fluff modifier.

If the dryer will not start, check the following:

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has not tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. [f

you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and

check that the gas supply line shutoff valve is open.

• [f the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as

outlined above.

• If the gas supply line shutoff valve is open, contact a qualified technician.

DRYER USE

STARTING YOUR DRYER

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

This manual covers several different models. Your dryer may not have all of the cycles and

features described.

Follow these basic steps to start your dryer. Please refer to specific sections of this manual for

more detailed information.

1. Clean lint screen before each load. See "Cleaning the ].int Screen."

2. Place laundry into dryer and shut door.

3. Press POWER.

Turn the knob to the selected cycle. The preset settings for Sensor Dry Cycles or Timed

Cycles will illuminate. The estimated (automatic cycle) or actual (timed) cycle time (in

minutes) will show in the display.

NOTE: A default time is displayed when an automatic cycle is selected. During the first

few minutes of the drying process, the cycle time may automatically vary from the default

time based on the size and fabric type of the load. [bward the end of the drying process,

the estimated time display will adjust again, showing the final drying time.

To use a Sensor Dry Cycle

• Press POWER.

• Turn the knob to desired Sensor Dry Cycle.

• Select DRYNESS to adjust how dry you want the load. As the cycle runs, the control

senses the dryness of the load and adjusts the time automatically for the selected

dryness level.

The default dryness setting is Normal when a Sensor Dry Cycle is selected. You can

select a different dryness level, depending on your load, by pressing [Dryness and

choosing More, Less or Damp. Selecting More, Less or Damp automatically adjusts

the sensed time needed. Once a dryness level is set, it cannot be changed without

stopping the cycle.

• Select the desired Options.

To make changes during a Sensor Dry Cycle:

• Press PAUSE/CANCEl.

• Adjust Dryness.

• MORE

• NORMAL

• LESS

NOTE: Dryness selections can be made only while using Sensor [Dry Cycles.

How the Sensi-Care rM Drying System Works

Moisture-sensing strips and temperature sensors inside the dryer drum monitor how fast

the load is drying, how hot the air should lye and when clothes are dry. [-he system

automatically stops the cycle to help save time and avoid overdrying.

To use a Timed Cycle

• Turn knob to desired limed Cycle.

• Press the TIMED CYCI.E ADJUST up or down arrows until the desired drying time is

displayed. Press the up or down arrows and the time will change by 1-minute

intervals. Press and hold the up or down arrows and the time will change by 5-minute

intervals.

NOTE: The Timed Cycle Adjust features can lye used only with Timed Cycles.

(9@

TIMED CYCLE

ADJUST

Press FEMP until the desired temperature illuminates.

• HIGH

• MEDIUM

• ow

• _XTRA lOW

FI t_FF

TEMP

IMD

CYCLES

NOTE: The ]emp feature can lye used only with Timed Cycles.

NOTE: During aTimed Cycle, you can change the settings for lime, [emp, the Wrinkle

Prevent setting and the End of Cycle Signal.

5. (OPTIONAl. STEP)If desired, select OPTIONS. For more details, see "Options."

6. (OPTIONAl. STEP)If desired, press END OF CYCI.E SIGNAl. A signal will sound to alert

you when a cycle ends. For more details, see "End of Cycle Signal."

7. PressSTART.Be sure the door is closed.

• If you do not press Start within 5 minutes of selecting the cycle, the dryer

automatically shuts off.

• If you wish to end your drying cycle after pressing Start, press PAUSE/CANCEl. twice.

STOPPING, PAUSING OR RESTARTING

To stop or pause your dryer at any time

(-)pen tile door or press PAUSE/CANCEL once. Press PAUSE/CANCEl twice to cancel a cycle.

To restart the dryer

Close the door. Press START until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and

press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will

shut off. Select new cycle settings before restarting the dryer.

DRYING AND CYCLE TIPS

Select the correct cycle and dryness level or temperature for your load. If a Sensor Dry Cycle

is running, the display shows the estimated cycle time when your dryer is automatically

sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact

number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool

Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package instructions.

• fo reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is

especially important for permanent press, knits and synthetic fabrics.

• Avoid drying heavy work clothes together with lighter fabrics. This could cause

overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Sensor Dry or Timed Preset Cycle Settings chart (in the "Cycles" section) for a

guide to drying various loads.

• Drying temperature and dryness level are preset when you choose a Sensor Dry

Cycle. You can select a different dryness level, depending on your load, by pressing

Dryness and choosing More, Normal, less or Damp.

NOTE: You cannot use the Timed Cycle Adjust and you cannot choose a Temperature

with the Sensor Dry Cycles.

• If you wish to adjust the cycle length of a Timed Cycle, press the Timed Cycle Adjust

up or down arrows. Adjust the temperature of a Timed Cycle by pressing |emp until

the desired temperature is selected.

NOTE: You cannot choose a dryness level with Timed Cycles.

STATUS LIGHTS

Follow the progress of your dryer with the drying Status indicator lights.

Wrinkle Prevent Setting

The Wrinkle Prevent setting light illuminates when this option is selected. This indicator stays

on during the Wrinkle Prevent setting.

Indicator lights

Other indicator lights show Cycle, Modifiers, Options and Cycle Signal settings selected. The

display shows the estimated or actual time remaining.

CYCLES

Select the drying cycle that matches the type of load you are drying. See Sensor Dry or Timed

Preset Cycle Settings charts.

SENSOR DRY TIM_D

COOL WRINKLE

SENSING WET DAMP DOWN DRY PREVENT

,,o • • • • Oj

Sensing

• In a Sensor Dry Cycle, the Sensing light illuminates until a wet item is detected.

• In a Timed Cycle, the Sensing light illuminates at the beginning of a cycle and turns off

5 minutes into the cycle.

Wet

The Wet light illuminates at the beginning of a Sensor Dry Cycle if a wet item is detected.

• in a Sensor Dry Cycle, if a wet item is not detected after approximately 5 minutes, the

dryer goes directly into Cool Down. The Cool Down and the Wrinkle Prevent setting

indicators will illuminate, if selected.

• In a Timed Cycle, wet items are not detected. [he dryer will continue to run for the length

of time selected, and the Wet light will illuminate. ]he damp light will not illuminate.

Damp

The Damp light illuminates in a Sensor Dry Cycle when the laundry is approximately 80%

dry. Damp Dry Chime beeps, if selected. See "Options."

Cool Down

The Cool Down light illuminates during the cool down part of the cycle. [aundry cools for

ease in handling.

Dry

The Dry light illuminates when the drying cycle is finished. This indicator stays on during the

Wrinkle Prevent setting.

DRY CYCLES

Sensor Dry Cycles

Sensor Dry Cycles allow you to match the cycle to the load you are drying. See the following

Sensor Dry Preset Cycle Settings chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and automatically adjusts the drying

time for optimal drying.

Heavy Duty

Use this cycle to get high heat for heavyweight mixed loads, cottons and jeans.

Normal

Use this cycle to get medium heat for drying sturdy fabrics such as work clothes and sheets.

Wrinkle Control

Use this cycle to get low heat for drying no-iron fabrics, such as sport shirts, casual business

clothes and permanent press blends.

Delicate

Use this cycle to get extra-low heat to gently dry items such as lingerie, blouses or washable

knit fabrics.

Sensor Dry Preset Cycle Settings

Sensor Dry Cycles Temperature

Load Type

HEAVY DUTY High

Heavyweight mixed loads, cottons, jeans

NORMAL Medium

Corduroys, work clothes, sheets

WRINKLE CONTROL Low

Business casual clothes, permanent press, synthetics

DELICATE Extra-[ ow

Iingerie, [)louses, washable knit fabrics

Timed Cycles

Use Timed Cycles to select a specific amount of drying time and a drying temperature. When

a Timed Cycle is selected, the Estimated Time Remaining display shows the actual time

remaining in your cycle. You can change the actual time in the cycle by pressing the Timed

Cycle Adjust up or down arrows. See "Changing Cycles, Modifiers and Options."

NOTE: Timed Cycles may also be used with the dryer rack. See "Dryer Rack."

Timed Dry

Use this cycle to complete drying if items are still damp after a Sensor Dry Cycle. Timed Dry

is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.

[ ightweight garments, such as exercise wear, can be clriecl using Timed Dry on a low

temperature setting.

Rapid Dry

Use this cycle for drying small loads or loads that need ashort drying time.

Freshen Up

Use this cycle to help smooth out wrinkles from such items as clothes packed in a suitcase or

items wrinkled from being left in the dryer too long.

Timed Preset Cycle Settings

Timed Cycles Default Temperature Default Time

Load Type (Minutes)

TIMED DrY High 40

Heavyweight, bulky items, work clothes

rAPID DrY Medium 24

Small loads

FRESHEN UP Medium 20

Helps to smooth out wrinkles

MODIFIERS

Sensor Dry Cycle Modifiers

Use the DRYNESS button to select dryness levels for the Sensor Dry Cycles. Press DRYNESS

until the desired Dryness setting illuminates.

[he preset dryness setting is Normal when a Sensor Dry Cycle is selected. You can select a

different dryness level, depending on your load, by pressing Dryness and choosing More,

Normal, Less or Damp. Selecting More, Normal, i.ess or Damp automatically adjusts the

dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed

without stopping the cycle.

• MORE

• NOrMA_

• LESS

DRYNESS

s_soR b_Y

O_Y

NOTE: Dryness Level selections cannot be used with the Timed Cycles.

Timed Cycle Modifiers

Use the TEMPERAlURE button to select temperatures for the Timed Cycles. Press TEMP until

the desired temperature setting illuminates.

MEDIUM

• ow

• _X-RA lOW

T[MP

¢YCES

NOTE: [emperature modifiers cannot be used with the Sensor Dry Cycles.

Air Fluff

Use the Air Fluff Modifier for items that require drying without heat such as rubber, plastic

and heat-sensitive fabrics. ]his table shows examples of items that can be dried using Air

Fluff.

Type of Load Time* (Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset cycle to complete drying, if needed.

When using Air Fluff

• Check that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Air Fluff is not available with Sensor Dry Cycles.

OPTIONS

You can customize your cycles by selecting options.

DRUM

LIGHT

WRINKLE

PREVENT

DAMP DRY

CHIME

OPTIONS

Drum Light

On some models, select Drum light to turn on the light inside tile dryer drum. During a cycle,

if Drum light is selected, the drum light turns on and will remain on until DRUM IEGHT is

pressed again, the door is opened and closed, or the door is left open for 5 minutes.

When the dryer is not running, the drum light will turn on when DRUM LIGHT is pressed or

the dryer door is opened, and it will remain on until the dryer door has been open for

5 minutes, the dryer door is closed or DRUM LIGHT is pressed again.

Press DRUM lIGHT at any time to turn the drum light ON or OFF.

Wrinkle Prevent Setting

The Wrinkle Prevent setting helps keep wrinkles from forming when you cannot unload the

dryer promptly at the end of a cycle. During this option, the dryer stops tumbling and then

tumbles again for a brief period.

• Press the Wrinkle Prevent setting to get up to 120 minutes of heat-free, periodic tumbling

at the end of a cycle.

• Stop the Wrinkle Prevent setting at any time by pressing Wrinkle Prevent setting or

opening the dryer door.

• For the Wrinkle Control Cycle, the Wrinkle Prevent setting is preset to ON. ]he other

Sensor Dry Cycles will retain the Wrinkle Prevent setting. For example, if you select the

Wrinkle Prevent setting in the Normal cycle, the Wrinkle Prevent setting will be on the

next time you select the Normal cycle.

NOTE: If you do not select the Wrinkle Prevent setting, the dryer stops after cool down.

Damp Dry Chime

Select the [)amp Dry Chime to alert you that your clothes are approximately 80% dry. lhis is

useful when you want to remove lightweight items in a mixed load to avoid overdrying or

remove partially dry items that may need ironing.

The Damp Dry Chime is useful when drying bedsheets/linens in a mixed load. When the

signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the

door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying

process.

NOTE: The Damp Dry Chime is available only with the Sensor Dry Cycles.

END OF CYCLE SIGNAL

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the drying cycle is finished.

Promptly removing clothes at the end of the cycle reduces wrinkling.

Press END OF CYCLE SIGNAl until the desired volume (High, I.ow or OFF) is selected.

• HIG[

• LOW

END OF

CYCLE

SIGNAL

NOTE: When the Wrinkle Prevent setting is selected and the End of Cycle Signal is on, a tone

sounds every 5 minutes until the clothes are removed, or the Wrinkle Prevent setting ends.

CHANGING CYCLES, MODIFIERS

AND OPTIONS

You can change Sensor Dry and limed Cycles, Modifiers and Options anytime before

pressing Start.

• Three short tones sound if an unavailable combination is selected. The last selection will

not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice.

2. Select the desired cycle and options.

3. Press START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer

automatically shuts off.

La page charge ...

Maytag MGD6400TB - Bravos Gas Dryer Mode d'emploi

Marque: Maytag

Modèle: MGD6400TB - Bravos Gas Dryer

Catégorie: Sèche-linge électriques

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MGD6400TB - Bravos Gas Dryer User guide
español: Maytag MGD6400TB - Bravos Gas Dryer Guía del usuario

Maytag MGD6400TB - Bravos Gas Dryer Mode d'emploi

Maytag MGD6400TB - Bravos Gas Dryer Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents