Sony CDP-XA555ES Manuel utilisateur

Catégorie
Lecteurs de cassettes
Taper
Manuel utilisateur
Getting Started
3-867-064-11 (1)
1999 by Sony Corporation
Operating Instructions
Mode d’emploi
Manual de instrucciones
GB
FR
ES
CDP-XA555ES
Compact Disc
Player
2
GB
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.
Do not install the
appliance in a confined
space, such as a bookcase
or built-in cabinet.
Welcome!
Thank you for purchasing the Sony
Compact Disc Player. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
About This Manual
The instructions in this manual are for
model CDP-XA555ES.
Conventions
Instructions in this manual describe
the controls on the player.
You can also use the controls on the
remote if they have the same or similar
names as those on the player.
The following icons are used in this
manual:
Indicates that you can do the
task using the remote.
Indicates hints and tips for
making the task easier.
This appliance is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
Getting Started
GB
3
GB
TABLE OF CONTENTS
Getting Started
Unpacking............................................................................................................................. 4
Hooking Up the System...................................................................................................... 4
Playing a CD............................................................................................................................. 6
Playing CDs
Customising the Sound of Your Music (Digital Filter Function).................................. 8
Using the Display ................................................................................................................ 9
Locating a Specific Track .................................................................................................. 10
Locating a Particular Point in a Track ............................................................................ 11
Playing Tracks Repeatedly ............................................................................................... 11
Playing in Random Order (Shuffle Play) ....................................................................... 12
Creating Your Own Programme (Programme Play) .................................................... 13
Playing Only Specific Tracks (Delete Play).................................................................... 15
Recording From CDs
Recording Your Own Programme .................................................................................. 16
Recording a CD by Specifying the Tape Length (Time Edit/Just Edit) .................... 17
Fading In or Out................................................................................................................. 18
Useful Tips for Recording ................................................................................................ 19
Storing Information About CDs (Custom Files)
What You Can Do With the Custom Files ..................................................................... 20
Indexing a Disc (Custom Index) ...................................................................................... 20
Storing Specific Tracks of a Disc (Delete Bank)............................................................. 22
Additional Information
Precautions ......................................................................................................................... 23
Notes on CDs...................................................................................................................... 23
Troubleshooting ................................................................................................................. 24
Specifications ...................................................................................................................... 24
Index........................................................................................................................................... 25
Getting Started
4
GB
CD
ANALOG OUT
FIXED
Unpacking
Check that you received the following items:
Audio connecting cord (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
Stabilizer (1)
Inserting batteries into the remote
You can control the player using the supplied remote.
Insert two R6 (size AA) batteries by matching the +
and – on the batteries to the diagram inside the battery
compartment.
Insert the negative (–) end first, then push in and down
until the positive (+) end clicks into the position.
When using the remote, point it at the remote sensor g
on the player.
Hooking Up the System
Overview
This section describes how to hook up the CD player to
an amplifier. Be sure to turn off the power of each
component before making the connections.
When to replace batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the player,
replace all the batteries with new ones.
Notes
Do not leave the remote near an extremely hot or humid
place.
Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
To mains
CD player
DIGITAL OUT
(COAXIAL)
ANALOG OUT
(VARIABLE)
DIGITAL OUT
(OPTICAL)
To mains
Amplifier
What cords will I need?
pWhen making analog hookups
Audio cord (supplied) (1)
White
(L)
Red
(R)
White
(L)
Red
(R)
pWhen making digital hookups
Optical cable (not supplied)
Coaxial cable (not supplied)
: Signal flow
DIGITAL OUT
ON/OFF
Getting Started
5
GB
Hookups
pWhen making analog hookups
When connecting an audio cord, be sure to match the
colour-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
Amplifier
AmplifierCD player
If you have an analog power amplifier
Connect the amplifier via the ANALOG OUT (VARIABLE)
jacks using the supplied audio cord. Be sure to set the
DIGITAL OUT ON/OFF switch to OFF (the factory setting)
when you make this connection. You can adjust the output
level with the ANALOG OUT/PHONE LEVEL control on
the player or the ANALOG OUT LEVEL buttons on the
remote.
If you have a digital component with an optical digital
input connector
Connect the component via the DIGITAL OUT (OPTICAL)
connector using the optical cable (not supplied). Take off
the cap and plug in the optical cable.
CD player
Digital component
CD player
FIXED
L
R
L
R
VARIABLE
INPUT
CD
L
R
ANALOG OUT
ANALOG OUT
FIXED
L
R
L
R
VARIABLE
INPUT
CD
L
R
DIGITAL OUT
OPTICAL
ON
OFF
COAXIAL
DIGITAL IN
OPTICAL
If you have a digital component with a coaxial digital
input connector
Connect the component via the DIGITAL OUT (COAXIAL)
connector using the coaxial cable (not supplied).
Digital componentCD player
Note
When you connect via the DIGITAL OUT connector, noise
may occur when you play CD software other than music, such
as a CD-ROM.
Connecting the mains lead
Connect the mains lead to the mains.
Removing the notice sheet
Remove the notice sheet from the player before using.
pWhen making digital hookups
You can prevent deterioration of the signal during
transmission, since the music signal output through
the digital output connectors retains digital form.
You can connect a digital component such as a
digital amplifier, D/A converter, DAT, or MD. When
you connect a DAT or MD, you can make digital
recordings from CDs.
Be sure to set the DIGITAL OUT ON/OFF switch to
ON when you make this connection.
Note that you cannot use the fade in/out function
(page 18) when making this connection.
OPTICAL COAXIAL
DIGITAL OUT
ON
OFF
DIGITAL IN
COAXIAL
Basic Operations
6
GB
Playing a CD
23
1
2
See pages 4 – 5 for hookup
information.
If you turn on the player with
a CD in the tray
You can start playing
automatically from the
beginning of the CD. If you
connect a commercially
available timer, you can set
the timer to play at any time.
If––––– appears in the
display
Place the supplied stabilizer
on the CD.
If you do not, this indication
appears.
Note
In Step 3, be careful not place
two or more CDs on the disc
tray.
Otherwise, you may damage the
discs and/or the player.
If play doesn’t start from the
first track
Press PLAY MODE
repeatedly until
“SHUFFLE,” “PROGRAM”
and “CUSTOM INDEX”
disappear from the display
(or press CONTINUE on the
remote).
Turn on the amplifier and select the CD player position.
Press U to turn on the player.
Press § OPEN/CLOSE, and place a CD on the tray.
4
CHECK CLEAR FILTER
PUSH ENTER
AMS
REPEAT TIME
TIME FADE FILE ERASE
EDIT/
PHONE LEVEL
ANALOG OUT
PHONES
MIN MAX
OPEN/CLOSE
MODE
PLAY
Connect the
headphones.
Adjust the
headphones volume.*
Press (.
The disc tray closes and the player plays all the tracks once
(Continuous Play).
Adjust the volume on the amplifier.
4
3
With the label side up
Place the supplied stabilizer on the
CD.
*The output level from the ANALOG OUT
(VARIABLE) jacks will also change.
Basic Operations
Basic Operations
Basic Operations
7
GB
To stop playback
Press p.
When you want to
Pause
Resume play after pause
Go to the next track
Go back to the preceding track
Stop play and remove the CD
You need to
Press P
Press P or (
Turn AMS ± clockwise. (When
using the remote, press +.)
Turn AMS ± anticlockwise.
(When using the remote, press =.)
Press § OPEN/CLOSE
Playing CDs
8
GB
Customising the Sound of Your
Music (Digital Filter Function)
This player has a variable coefficient (V.C.) digital
filter. By selecting the type of filter you want, you can
adjust the sound to match your system, your room, the
music source, etc.
AMS ±FILTER
3 Push AMS ± to select the filter.
The original display reappears.
The selected digital filter number is stored in
memory even if you turn off the power.
You can also change the digital filter number by
pressing the FILTER button while the indicator is
flashing.
Selecting the filter using the remote Z
1 Press DIGITAL FILTER.
The display shows the currently selected filter
number and the filter indicator flashes.
2 Press DIGITAL FILTER repeatedly until the
display shows the digital filter number you want.
The digital filter number is stored and the original
display reappears.
Characteristics of each digital filter
The contents and characteristics of the five digital
filters are as follows:
Std: Standard (sharp roll-off)
Provides a wide frequency range and spatial feeling, as
it holds the most information among the five filters.
Suitable for playback of classical music.
1: Clear (slow roll-off)
Provides smooth and powerful sound with clear image
position.
Suitable for playback of jazz band performances and
jazz vocals.
2: Plain (slow roll-off)
Provides fresh and energetic sound with rich vocal
expression.
Suitable for playback of vocal-performances.
3: Fine (slow roll-off)
Provides well-balanced natural sound, with a of large
scale feel and rich reverberation.
Suitable for listening to any kind of music when you
are relaxed.
4: Silky (slow roll-off)
Provides a wide scale feel with associated subtleties.
Suitable for light classical music, especially strings.
DIGITAL FILTER
n Std n 1 n 2 n 3 n 4
Playing CDs
Selecting the filter directly on the player
1 Press FILTER.
The display shows the currently selected filter
number and the filter indicator flashes.
2 Turn AMS ± until the digital filter number
you want appears in the display.
As you turn the AMS ± control, the digital
filter number changes cyclically as follows:
If you are playing a disc, the sound will be
interrupted momentarily.
Playing CDs
9
GB
Sharp roll-off filter
Slow roll-off filter
Pre-ringing Post-ringing Pre-ringing
Post-ringing
Comparison of impulse response for sharp roll-off filter
and slow roll-off filter
-120
0
0
22.05k
Response
(dB)
(Slow roll-off filter)
(Sharp roll-off filter)
Frequency (Hz)
Comparison of cutoff characteristics for sharp roll-off filter
and slow roll-off filter
What is a variable coefficient (V.C.) digital
filter?
CD players use digital filters to eliminate the noise
generated during sampling. You can change the tone of
your music by changing the cutoff characteristics of the
digital filter.
Sharp roll-off and slow roll-off
Digital filters can be roughly classified into sharp roll-
off types and slow roll-off types, according to their
cutoff characteristics.
Sharp roll-off filters quickly cut off noise over
22.05 kHz generated during sampling. This is a
superior way of completely reproducing signals below
20 kHz and is the basic principle behind digital audio.
On the other hand, slow roll-off filters cut off noise
generated during sampling, and are able to hold pre-
ringing and post-ringing (a kind of sound smearing) in
the impulse response signal to a minimum.
Note
The Digital Filter function primarily changes characteristics
outside the audible frequency. They cannot affect changes
within the audible frequency such as those provided by the
tone controls of the amplifier. Therefore, with certain
combinations of hardware and software, there may be no
noticeable effect after switching the filter.
Using the Display
You can check information about the disc using the
display.
TIME
DISPLAY MODE
Checking the total number and playing
time of the tracks
Press TIME before you start playing.
The display shows the total number of tracks, total
playing time, and music calendar.
Total playing time
Total number of
tracks
Music calendar
TIME
12345
678910
MIN SEC
While in Shuffle Play mode (“SHUFFLE” appears in
the display; see page 12), a one-second access time
blank is added between each track. This increase is
automatically added to the total playing time in the
display.
If the disc has more than 15 tracks, the z indication
appears next to 15 on the music calendar.
The information also appears when you press
§ OPEN/CLOSE to close the disc tray.
Playing CDs
10
GB
Display information while playing a disc
While playing a disc, the display shows the current
track number, index number, playing time, and the
music calendar.
Current track
number
Playing time
Music calendar
Index number (page 11) or Custom Index
number (page 20)
The track numbers in the music calendar disappear
after they are played.
Checking the remaining time
Each time you press TIME while playing a disc, the
display changes as shown in the chart below.
If the remaining time exceeds 100 minutes in programme
mode, “––.–– appears instead of the remaining time.
Press
Press
Playing time
and number
of the current
track
Remaining
time on the
current
track
Remaining
time on the
disc
Press
12345
678910
MIN SECINDEX
Locating a Specific Track
You can quickly locate any track while playing a disc
using the AMS (Automatic Music Sensor) on the player
or the number buttons on the remote.
Number
buttons
>10
=/+
To locate
The next or
succeeding tracks
The current or
preceding tracks
A specific track
directly Z
When you directly locate a track numbered over 10
Z
Press >10 first, then the corresponding number buttons
on the remote. To enter “0,” use button 10/0.
Example: To play track number 30
Press >10 first, then 3 and 10/0.
You need to
Turn AMS ± clockwise until
you find the track. When using the
remote, press + repeatedly until you
find the track.
Turn AMS ± anticlockwise
until you find the track. When using
the remote, press = repeatedly until
you find the track.
Press the number button of the track
on the remote.
AMS ±
Turning off the music calendar in the
display
Each time you press DISPLAY MODE on the remote
while playing a disc, the music calendar turns off and
on alternately in the display.
12345
678910
MIN SECINDEX
12345
678910
MIN SECINDEX
12345
678910
MIN SEC
Playing CDs
11
GB
Playing Tracks Repeatedly
You can play tracks repeatedly in any play mode.
REPEAT
A˜B
REPEAT
Press REPEAT while playing a disc.
“REPEAT” appears in the display. The player repeats
the tracks as follows:
When the disc is played in
Continuous Play (page 6)
Shuffle Play (page 12)
Programme Play (page 13)
Delete Play (page 15)
Delete Shuffle Play
(page 13, 15)
Custom Index Play
(page 21)
To cancel Repeat Play
Press REPEAT repeatedly until “REPEAT” disappears from
the display.
The player repeats
All the tracks
All the tracks in random order
The same programme
All the remaining tracks
All the remaining tracks in
random order
The portion between two
indexes
Locating a Particular Point in a
Track
You can also locate a particular point in a track while
playing a disc.
0/)
INDEX C/c
0/)
To locate a point
While monitoring the
sound
Quickly by observing
the display during
pause
Using an index (only
for indexed discs)
What is an index?
It is a number that divides a track or a disc into sections,
enabling you to easily locate a desired point. You can
determine if a disc uses indexes by its packaging.
Note
If “ ” appears in the display, the disc has reached the end
while you were pressing ). Press 0 or turn
AMS ± anticlockwise to go back.
Press
) (forward) or 0 (backward)
and hold down until you find the
point
0/) and hold down until you
find the point. You will not hear the
sound during the operation.
INDEX C/c on the remote
repeatedly until you find the point
Playing CDs
12
GB
Repeating the current track
You can repeat just the current track.
While the track you want is being played, press
REPEAT repeatedly until “REPEAT 1” appears in the
display.
Note
You cannot repeat the current track while the disc is played in
Custom Index Play mode (see page 21).
Repeating a Specific Portion (A˜B Repeat)
You can play a specific portion in a track repeatedly.
This might be useful when you want to memorize
lyrics.
Note that you cannot repeat a portion extending
through two tracks.
1 While playing a disc, press A˜B on the remote
when you find the starting point (point A) to be
played repeatedly.
“A-” of “REPEAT A-” flashes in the display.
2 When you reach the ending point (point B), press
A˜B again.
“REPEAT A-B” appears. The player plays this
specific portion repeatedly.
To cancel A˜B Repeat
Press REPEAT.
Setting a new starting point
You can move the repeating portion ahead by
changing the starting point.
1 Press A˜B while the player is repeating the
specific portion.
The ending point B becomes the new starting point
A. “A-” of “REPEAT A-” flashes in the display.
2 When you reach the new ending point (point B),
press A˜B again.
“REPEAT A-B” appears. The player repeats
between the new starting and ending points.
When you want to restart from the starting point A
Press ( during A˜B Repeat.
Playing in Random Order
(Shuffle Play)
You can have the player “shuffle” tracks and play in
random order.
(
PLAY MODE
1 Press PLAY MODE repeatedly until “SHUFFLE”
appears in the display.
When using the remote, press SHUFFLE.
SHUFFLE
CONTINUE
·
12345
678910
SHUFFLE
2 Press ( to start Shuffle Play.
The
indication appears while the player is
“shuffling” the tracks.
To cancel Shuffle Play
Press PLAY MODE four times (or CONTINUE on the remote).
Playing CDs
13
GB
Creating Your Own
Programme (Programme Play)
You can arrange the order of the tracks on a disc and
create your own programme. The programme can
contain up to 24 tracks.
PLAY MODE
2 Turn AMS ± until the track number you
want appears in the display.
The playing order and the track number being
programmed flash, and the total playing time
including the track appears in the display.
AMS ±
CHECK
p(
CLEAR
Track number being
programmed
25
8
PROGRAM
MIN SEC
STEP
Total playing time
Playing order
Programmed
tracks
3 Push AMS ± to select the track.
Last programmed
track
Playing order
Programmed
tracks
Total playing time
25
8
PROGRAM
MIN SEC
STEP
Creating a programme on the player
1 Press PLAY MODE repeatedly in stop mode until
“PROGRAM” appears in the display.
12345
678910
PROGRAM
You can start Shuffle Play while playing
Press PLAY MODE once (or SHUFFLE on the remote) to
start Shuffle Play from the current track.
You can delete the undesired tracks during Shuffle
Play (Delete Shuffle Play)
Press the number button of the track you want to delete
on the remote.
The track number and “OFF” appear in the display, and
then the track number disappears from the music
calendar.
If you want to restore the track, press the number button
again.
To restore all the tracks, press p in stop mode.
If you’ve made a mistake
Press CLEAR, then repeat Steps 2 and 3.
4 Repeat Steps 2 and 3 to programme other tracks in
the order you want.
5 Press ( to start Programme Play.
To cancel Programme Play
Press PLAY MODE three times.
When tracks which are not numerically consecutive
on the disc are programmed consecutively (i.e. 1, 3,
5 etc.)
A one-second access time blank is added between the
tracks.
The programme remains in memory even after
Programme Play ends
When you press (, you can play the same programme
again.
CONTINUE
Number
buttons
>10
·
=/+
PROGRAM
CLEAR
CHECK
p
Playing CDs
14
GB
Last programmed
track
Playing order
Total playing time
Programmed
tracks
25
8
PROGRAM
MIN SEC
STEP
To select a track with a number over 10
Use the >10 button (see page 10).
If you’ve made a mistake
Press CLEAR, then press the correct track number.
3 Press · to start Programme Play.
To cancel Programme Play
Press CONTINUE.
You can check the total playing time while
programming using the remote (Programme Edit)
To select a track, press = or + and check the total
playing time. Then press PROGRAM to confirm your
selection.
When tracks which are not numerically consecutive
on the disc are programmed consecutively (i.e. 1, 3,
5 etc.)
A one-second access time blank is added between the
tracks.
The programme remains in memory even after
Programme Play ends
When you press ·, you can play the same programme
again.
Notes
––.–– appears instead of the total playing time in the
display when it exceeds 100 minutes.
“FULL” appears in the display when you try to add a track
to a programme which already contains 24 tracks.
Notes
––.–– appears instead of the total playing time in the
display when it exceeds 100 minutes.
“FULL” appears in the display when you try to add a track
to a programme which already contains 24 tracks.
Creating a programme using the remote
1 Press PROGRAM before you start playing.
“PROGRAM” appears in the display.
2 Press the number buttons of the tracks you want to
programme in the order you want.
Example: To programme the tracks 2, 8, and 5
Press the number buttons in order 2, 8,
and 5.
Checking the track order
You can check your programme before or after you
start playing.
Press CHECK.
Each time you press this button, the display shows the
track numbers in the programmed order. After the last
track in the programme, the display shows “End” and
returns to the original display. If you check the order
after you start playing, the display shows only the
remaining track numbers.
Changing the track order
You can change your programme before you start
playing.
To
Erase a track
Erase the last track in the
programme
Add tracks to the end of
the programme
Change the whole
programme completely
You need to
Press CHECK until the undesired
track appears in the display, then
press CLEAR.
Press CLEAR. Each time you press
the button, the last track will be
cleared.
Turn AMS ± until the track
number you want to add appears,
then push AMS ±.
When using the remote, press the
number button of the track to be
added.
Hold down CLEAR until “ALL
CLr” appears in the display. Create
a new programme following the
programming procedure.
Playing CDs
15
GB
CONTINUE
SHUFFLE
CLEAR
>10
Number
buttons
·
1 Press SHUFFLE.
“SHUFFLE” appears in the display.
2 Press the number buttons of the tracks you want to
delete.
The track numbers disappear from the music
calendar after “OFF” appears for a while.
To delete a track numbered over 10, use the >10
button (see page 10).
If you’ve made a mistake
Press the number button of the track. “On” appears in
the display and the track will be restored.
3 After you’ve deleted all the undesired tracks, press
CONTINUE.
“SHUFFLE” disappears from the display.
If you press PLAY MODE on the player instead of
CONTINUE on the remote
The deleted tracks will be restored. Be sure to do this step
with the remote.
4 Press · to start Delete Play.
Playing Only Specific Tracks
(Delete Play)
You can delete the undesired tracks and play only the
remaining tracks.
To cancel Delete Play
Press p in stop mode.
The player keeps a record of the deleted tracks in
memory even after the Delete Play ends
When you press ·, you can play only the remaining
tracks again.
You can play the tracks in random order (Delete
Shuffle Play)
Just skip Step 3 in the above procedure.
You can delete a track while playing
Press CLEAR while the track is being played. The player
deletes the track and starts playing the next track.
You can store the deleted tracks of each disc
See “Storing Specific Tracks of a Disc” on page 22.
Recording From CDs
16
GB
Recording Your Own
Programme
You can record a programme you’ve created onto a
tape, DAT, or MD. The programme can contain up to
24 tracks.
By inserting a pause during programming, you can
divide the programme into two for recording on both
sides of a tape.
1 Create your programme (when recording onto a
tape, first decide the programme for side A) while
checking the total playing time indicated in the
display.
See “Creating Your Own Programme” on page 13.
2 When you record on both sides of the tape, press
P to insert a pause.
The “P” indication appears in the display and the
playing time is reset to “0.00.”
When you record on one side of the tape or on a
DAT or MD, skip this step and go to Step 4.
A pause is counted as one track
You can programme up to 23 tracks when you insert a
pause.
3 Repeat Step 1 to create the programme for side B.
4 Start recording on the deck and then press ( on
the player.
When you record on both sides of the tape, the
player pauses at the end of the programme for side
A.
5 To record on side B, reverse the tape and press (
or P on the player to resume playing.
You can automatically insert a blank space of 3
seconds between each track
Use the Auto Space function (see page 19).
You can check the total playing time while
programming
Use the Programme Edit function (see page 14).
To check and change your programme
See page 14.
“SIDE-A” appears while checking the programme for
side A, and “SIDE-B” while checking the programme for
side B.
P(PLAY MODE
Recording From CDs
CHECK
CLEAR AMS ±
CONTINUE
PROGRAM
Number
buttons
>10
P
=/+
CLEAR
CHECK
·
Recording From CDs
17
GB
Recording From CDs
1 Press EDIT/TIME FADE before you start playing
as follows:
To select Time Edit, press the button once.
“EDIT” appears and “SIDE-A” flashes in the
display.
To select Just Edit, press the button twice.
JUST
EDIT
( )
” appears and “SIDE-A” flashes in the
display.
Recording a CD by Specifying
the Tape Length (Time Edit/Just
Edit)
You can have the player create a programme that will
fit the length of the tape. Select one of the following
options:
Time Edit: automatically creates a programme,
keeping the original order of the disc.
Just Edit: automatically arranges the track order to fit
the tape length.
The programme can contain up to 24 tracks (a pause
inserted between tracks is counted as one track).
Note that tracks with numbers over 24 cannot be
programmed.
(EDIT/TIME FADE
AMS ±
P
0/)
PLAY MODE
3 Press EDIT/TIME FADE to have the player create
the programme.
The display shows the tracks to be recorded.
“SIDE-B” flashes in the display.
4 When you record on both sides of the tape, press
EDIT/TIME FADE again.
The player inserts a pause, then creates the
programme for side B. The display shows the
programmed tracks.
When you record on one side of the tape or on a
DAT or MD, skip this step.
5 Start recording on the deck and then press ( on
the player.
When you record on both sides of the tape, the
player pauses at the end of the programme for side
A.
6 To continue recording on side B, reverse the tape
and press ( or P on the player to resume
playing.
To cancel Time Edit/Just Edit
Press PLAY MODE repeatedly until “SHUFFLE,”
“PROGRAM,” and “CUSTOM INDEX” disappear from the
display (or press CONTINUE on the remote).
You can programme the tracks you want in advance
Select the tracks before doing the above procedure. The
player creates a programme from the remaining tracks.
In this case, you cannot select “HALF” to specify the tape
length.
You can freely specify the tape length
Set the tape length using AMS ±.
Example: When the tape length of one side is 30 minutes
and 15 seconds
1 To set the minutes, turn AMS ±
until “30” appears in the display, then push
AMS ±.
2 To set the seconds, turn AMS ±
until “15” appears in the display, then push
AMS ±.
When tracks which are not numerically consecutive
on the disc are programmed consecutively (i.e. 1, 3,
5 etc.)
A one-second access time blank is added between the
tracks.
You can automatically insert a blank space of 3
seconds between each track
Use the Auto Space function (see page 19).
You can check and change the programme
See page 14.
12345
678910
JUST
EDIT
SIDE–A
MIN SEC
2 Press 0 or ) to specify the tape length.
Each time you press these buttons, the display
changes as shown below, with the tape length of
one side following each indication.
n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - -. - - N
(23.00) (27.00) (30.00) (37.00) (45.00)
When you select “HALF”
The player sets the programme of each side to a half of
the total playing time of the disc. Note that you cannot
select “HALF” when the disc has more than 24 tracks.
Recording From CDs
18
GB
Changing the fading time
You can set the fading time from 2 to 10 seconds before
fading in or out. If you don’t set it, fading lasts for 5
seconds.
1 Press FADER before you start playing.
“5 SEC” appears and “FADE” flashes in the
display.
2 Press the number button to specify the fading time.
You can also specify the fading time by pressing
the 0/) buttons until the display shows the
time you want.
Fading out at the specified time
(Time Fade)
You can have the player fade out automatically by
specifying the playing time. Once you set the Time
Fade, it works twice, that is, the play fades out at the
end of both sides of a tape.
1 Press EDIT/TIME FADE three times before you
start playing.
TIME
FADE
( )
” and “SIDE-A” appear in the display.
2 Press 0 or ) to specify the playing time.
Each time you press these buttons, the display
changes as shown below, with the playing time of
one side following each indication.
n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - -. - - N
(23.00) (27.00) (30.00) (37.00) (45.00)
When you select “HALF”
The player sets the playing time to half of the total
playing time.
3 Press ( to start playing.
At the specified time the play fades out with
“FADE” flashing in the display and the player
pauses. “SIDE-B” appears in the display.
4 To record on side B, reverse the tape and press (
or P on the player to resume playing.
Again, the play fades out at the specified time.
To cancel Time Fade
Press EDIT/TIME FADE.
Fading In or Out
You can manually fade in or out to prevent tracks from
starting or ending abruptly.
Note that you cannot use this effect when you use the
DIGITAL OUT connector.
EDIT/TIME FADE (
0/)
FADER
Number
buttons
0/)
P
·
P
Press FADER
During pause. “FADE” flashes and
play fades in.
When you want to start fading out.
“FADE” flashes. The play fades out
and the player pauses.
To
Start play fading in
End play fading out
Recording From CDs
19
GB
Recording From CDs
Useful Tips for Recording
These functions make recording CDs more convenient.
PEAK SEARCH
A.SPACE
p
Adjusting the Recording Level (Peak Search)
The player locates a peak level among the tracks to be
recorded so you can adjust the recording level before
you start recording.
1 Before you start playing, press PEAK SEARCH.
“PEAK” flashes in the display and the player plays
the portion of with the high level.
2 Adjust the recording level on the deck.
3 Press p on the player to stop Peak Search.
“PEAK” disappears from the display.
Note
The portion with the peak level may differ every time you try
the adjustment on the same disc. However, the difference is,
so slight that you won’t find any problem in adjusting the
recording level precisely.
Locating each track on a tape using the
AMS function (Auto Space)
The Auto Space function inserts a blank space of 3
seconds between each track while playing, and enables
you to locate each track using the AMS function of the
deck.
Before you start playing, press A.SPACE.
“AUTO SPACE” appears in the display.
To cancel Auto Space
Press A.SPACE until “AUTO SPACE” disappears from the
display.
Note
If you use the Auto Space function when recording, for
example, a medley or symphony, the sound may be
interrupted where the track number changes. This happens
when the track numbers are assigned in the middle of a piece.
You can freely specify the playing time
See “You can freely specify the tape length” on page 17.
You can change discs during Time Fade
If the play ends before the specified fade-out time, (for
example, when you record CD-singles on a tape) change
the disc. The specified fade-out time is based on the
playing time.
You can fade in when you resume playing in Step 4
After you reverse the tape, press FADER.
Note
If you press 0 or ) during Time Fade Play, Time Fade
will be cancelled.
Storing Information About CDs (Custom Files)
20
GB
You can check the number of you can file
1 Remove the disc from the player.
2 Press § OPEN/CLOSE to close the disc tray.
3 Press TIME after the music calendar disappears
from the display.
The number of the Custom Files you can file
appears.
If “FULL” appears in the display
If the memory for Custom Files becomes full, the
player displays “FULL” when you press FILE to store
the information, and you cannot store information for
any more disc. If necessary, erase any unwanted
Custom Files (see page 22).
To erase all Custom Files of all discs
While holding down ERASE and FILE, press U to turn on the
player. “FILE CLr” appears in the display and all the custom
files will be erased.
Indexing a Disc (Custom Index)
You can index a disc at up to 8 points (for a disc with
32 tracks or less) or 5 points (for a disc with over 32
tracks) so that you can easily locate a desired point.
This might be useful when you play discs of
symphonies or concertos that divide one piece into
several tracks (see the example below).
Example
First
piece
1
23
Custom
Index No.
Second
piece
Third
piece
PLAY MODE
0/)
FILE
CHECK
Track No.
What You Can Do With the
Custom Files
The player can store 2 types of information called
“Custom Files” for each disc. Once you have stored
Custom Files for a disc, the player automatically recalls
what you have stored whenever you insert the disc.
Note that Custom Files will be erased if you don’t use
the player for about 1 month.
You can store this information:
When you use
Custom Index (page 20)
Delete Bank (page 22)
The Custom File indication lights up when you store
the corresponding information.
You can
Index the disc at up to 8 points
(for a disc with 32 tracks or less)
or 5 points (for a disc with over
32 tracks)
Delete unwanted tracks and
store just the tracks you want
Delete Bank
Custom Index
When you store a Custom File for a disc, the player
remembers how you played that disc last time even if
you removed the disc from the player (last mode
memory). When you insert the same disc again, play
begins in the previous play mode. The player also
remembers the duration of the fade in/out time if it
was changed.
Note that if you press ( to close the disc tray and
start playing, the player plays in the play mode
currently selected instead of the stored one.
Where are Custom Files stored?
Custom Files are stored not on the disc but in the
player’s memory. This means you cannot use Custom
Files when you play the disc on other players.
How many discs can you file?
You can file up to 224 discs in the Custom File.
The player counts a disc as one even if you store it in
both the Custom Index and Delete Bank.
C.FILE
DELETE
INDEX
123456789
ERASE
AMS ±
Storing Information About CDs (Custom Files)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Sony CDP-XA555ES Manuel utilisateur

Catégorie
Lecteurs de cassettes
Taper
Manuel utilisateur

dans d''autres langues