Real Fyre DVI Direct Vent Mode d'emploi

1

REV 1 - 1904251440

L-A2-415

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

IMPORTANT: READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OR USE.

INSTALLATION &

OWNER’S MANUAL

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Leave the building immediately.

• Immediately call the gas supplier

from a neighbor’s phone. Follow gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁ re department.

Installation and service must be performed

by a qualified professional installer,

service agency, or the gas supplier.

DESIGN CERTIFIED

to

Vented Gas Fireplace Heater

ANSI Z21.88

CSA 2.33

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

This appliance may be installed in an

aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certiﬁ ed kit is used.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

DANGER

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and shall be

installed for the protection of children and other at-risk

individuals.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDERN

TO TOUCH GLASS.

US

®

C

Direct Vent Inserts:

DVI-25m Series

DVI-30m Series

DVI-36m Series

DVI DIRECT VENT INSERTS - MILLIVOLT SYSTEM

2

REV 1 - 1904251440

L-A2-415

INSTALLATEUR :

Laissez ce manuel avec l'appareil.

CONSOMMATEUR:

Maintenez ce manuel pour la future référence.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

IMPORTANT: LISEZ CES INSTRUCTIONS

SOIGNEUSEMENT AVANT DE

COMMENCER L'INSTALLATION OU

L'UTILISATION.

Ne stockez pas ou n’employez pas l’essence

ou d’autres vapeurs et liquides inﬂ ammables

à proximité de ceci ou d’aucun autre appareil.

CE QUI À FAIRE SI VOUS SENTEZ LE GAZ:

• Ouvrez une fenêtre.

• N’essayez pas de n’allumer aucun appareil.

• Ne touchez aucun commutateur

électrique; n’utilisez aucun téléphone

dans le bâtiment.

• Quitter immédiatement le bâtiment.

• Appelez immédiatement le fournisseur

de gaz du téléphone du voisin. Suivez

les instructions du fournisseur de gaz.

• Si vous ne pouvez pas atteindre

le fournisseur de gaz, appelez le

département de feu.

L’installation et le service doivent être assurés

par un installateur qualiﬁ é et professionnel,

l’agence de service, ou le fournisseur de gaz.

Cet appareil peut être installé dans un marché des

accessoires, une maison de manière permanente

située et manufacturée (Etats-Unis seulement)

ou une caravane résidentielle, où non interdit par

des codes locaux.

Cet appareil sert seulement avec le type de gaz

indiqué de la plaque de contrôle. Cet appareil

n'est pas convertible pour l'usage avec d'autres

gaz, à moins qu'un kit certiﬁ é soit employé.

CONCEPTION CERTIFIÉE

à

Réchauffeur exhalé

de cheminée de gaz

ANSI Z21.88

CSA 2.33

INSTALLATION ET

MODE D'EMPLOI

DANGER

Une barrière conçu pour réduire le risque de brûlures par

le verre de visualisation chaude est fournie avec cet

appareil et doit être installé pour la protection des enfants

et autres personnes à risque.

UNA SURFACE VITRÉE CHAUDE

PEUT CAUSER DES BRÛLURES.

LAISSER REFROIDIR LA SURFACE

VITRÉE AVANT D'Y TOUCHER.

NE PERMETTEZ JAMAIS À UN

ENFANT DE TOUCHER LA

SURFACE VITRÉE.

ATTENTION:

INCENDIE OU EXPLOSION

Le non-respect des avertissements de sécurité

serait exactement entraîner des blessures graves,

la mort ou des dommages matériels.

US

®

C

Direct Vent Inserts:

DVI-25m Série

DVI-30m Série

DVI-36m Série

DVI INSERTS À ÉVACUATION DIRECTE - SYSTÈME MILLIVOLT

3

REV 1 - 1904251440

L-A2-415

TABLE OF CONTENTS

GETTING STARTED

IMPORTANT PRE-INSTALLATION AND SAFETY

INFORMATION ..............................................................5

NOTES PAGE .................................................................6

LISTING AND CODE APPROVALS .............................7

LISTING ...................................................................7

CODE REQUIREMENTS ...........................................7

COMMONWEALTH OF MASSACHUSETTS

REQUIREMENTS

...................................................... 7

SPECIFICATIONS AND DIMENSIONS .......................8

MINIMUM CLEARANCES .........................................13

TOOLS REQUIRED .....................................................13

REPLACEMENT PARTS LIST ....................................14

INSTALLATION REQUIREMENTS ...........................20

FIREPLACE REQUIREMENTS ................................20

GAS PRESSURE REQUIREMENTS ..........................21

VENTING REQUIREMENTS ....................................21

INSTALLATION

INSTALLATION ...........................................................23

BEFORE YOU BEGIN .............................................23

GAS SUPPLY SETUP ..............................................23

ELECTRICAL SETUP ..............................................23

VENTING ...............................................................24

DIRECT VENT INSERT ...........................................26

INSTALL BATTERIES ..............................................28

FIRST TIME PILOT LIGHTING TEST ......................29

FIRST TIME BURNER LIGHTING TEST ...................30

GAS PRESSURE TEST .............................................30

FIREBOX LINERS ...................................................31

LOG SET AND EMBER PLACEMENT ......................33

SURROUND FASCIA ...............................................34

FASTEN RETENTION BRACKET (if applicable) ........34

SECURE UNIT TO FLOOR ......................................34

GLASS PANEL.........................................................35

SURROUND DOOR ................................................35

INITIAL AIR SHUTTER ADJUSTMENT ....................35

FIRST TIME BURN-OFF PERIOD ...........................35

NOTES PAGE ...............................................................36

USE, CARE, & SERVICE

LIGHTING INSTRUCTIONS ......................................37

FOR YOUR SAFETY READ BEFORE LIGHTING ...... 37

LIGHTING THE PILOT ...........................................37

SURROUND DOOR ................................................39

REMOTE LIGHTING ............................................... 39

MANUAL LIGHTING...............................................41

SHUTTING DOWN .................................................. 41

REMOTE OPERATION INSTRUCTIONS ..................43

ORIENTATION ........................................................ 43

MANUAL MODE AND THERMOSTAT MODE ..........43

FAN OPERATION INSTRUCTIONS...........................45

TEMPERATURE INDICATOR (°F or °C) ..................45

KEY LOCK .............................................................45

OPERATING DURING A POWER OUTAGE .............45

SERVICING AND CLEANING ...................................47

ANNUAL CLEAN / INSPECTION .............................47

GLASS PANEL REMOVAL AND MAINTENANCE ......48

PILOT BURNER APPEARANCE ..............................48

AIR SHUTTER ADJUSTMENT .................................49

BATTERY REPLACEMENT ......................................51

SYNCHRONIZE REMOTE SYSTEM .......................... 52

FAN ASSEMBLY CLEANING .................................... 53

FUEL CONVERSION KITS ......................................53

NOTES PAGE ...............................................................54

TROUBLESHOOTING ................................................55

WARRANTY .................................................................58

IMPORTANT SAFETY INFORMATION

Congratulations on your purchase of an R. H. Peterson Co. Real Fyre direct vent insert. Made with pride in

America, your new insert complies with national safety standards and when installed per these instructions and

used as intended it will provide warmth and comfort to your home for many years.

Due to the extreme heat output of the insert, there is a risk of burns if care is not taken in the operation of

the unit. PLEASE READ THE SAFETY AND OPERATION INFORMATION AND WARNINGS IN THIS MANUAL

BEFORE USING YOUR INSERT. Be aware that glass panels and other surfaces get extremely HOT and can

cause burns if touched. Factory-provided barrier screens help to reduce the risk of serious burns as they can

prevent direct contact with the glass. However, barrier screens still retain heat and must not be touched. The

insert glass and surrounding material will remain HOT for a period of time after the unit is turned off, so caution

should be used at all times.

Refer to all safety information and warnings provided in this manual.

4

L'INFORMATION IMPORTANTE DE PRÉINSTALLATION ET DE SÛRETÉ

AVERTISSEMENT!

A. Lisez toutes les instructions. Ne pas installer ou d'utiliser cet appareil sans avoir lu et compris ce manuel. Ne pas

suivre les instructions de ce manuel se traduira par un appareil mal installé et opérationnel, annuler la garantie,

et peut être dangereux.

B. Une mauvaise installation, le réglage, la modiﬁ cation, le service, la maintenance, ou de l'utilisation peuvent causer

des blessures graves, la mort ou des dommages matériels. Reportez-vous à ce manuel. Pour de l'aide ou des

informations supplémentaires, consultez un technicien professionnel qualiﬁ é de service, un organisme de service

ou le fournisseur de gaz.Instructions à la terre électrique - Cet appareil est équipé d'un à trois broches (mise à la

terre) pour vous protéger contre les chocs électriques et doit être branchée directement dans une prise à trois

broches prise. Ne pas couper ou enlever la broche de terre de cette ﬁ che.

C. Dispositions pour la combustion adéquate et l'air de ventilation doit être maintenue.

Voir la EXIGENCES DE

VENTILATION section pour plus de détails.

D. Instructions à la terre électrique - Cet appareil est équipé d'un à trois broches (mise à la terre) pour vous protéger

contre les chocs électriques et doit être branchée directement dans une prise à trois broches prise. Ne pas couper

ou enlever la broche de terre de cette ﬁ che.

E. Ne pas placer les pièces conformément à ce manuel ou de l'échec d'utiliser seulement les pièces approuvées pour

cet appareil peut entraîner des dommages matériels ou des blessures corporelles.

F. Installation, maintenance et de réparation doit être effectuée par un technicien de service professionnel qualiﬁ é.

G. Un inspecteur en bâtiment local devriez revoir vos plans avant l'installation.

H. Soyez extrêmement prudent lors de la manipulation de ce produit et ses accessoires car ils ont des bords tranchants

qui peuvent causer des blessures.

I. Il est recommandé que les détecteurs de fumée sont installés dans la maison. Si possible, installez un détecteur

dans un couloir adjacent à la salle (pour éviter une fausse alarme de la chaleur de l'appareil). Cependant, vous

devez suivre les exigences du code local.

J. Toute modiﬁ cation ou altération peut annuler la garantie, la certiﬁ cation et les annonces de cet appareil.

K. Dégagements d'accessibilité adéquats pour l'entretien et doit être prévu.

L. Un dégagement sufﬁ sant autour des ouvertures d'air dans la chambre de combustion doit être maintenue.

M. Cet appareil au gaz ne doit pas être raccordé à un conduit de cheminée desservant un autre appareil de combustion

séparée à combustible solide.

N. Ne pas utiliser cet appareil si une pièce a été sous l'eau. Appelez immédiatement un technicien de service qualiﬁ é

pour inspecter l'appareil et pour remplacer toute pièce du système de contrôle et de contrôle du gaz qui a été sous

l'eau.

O. En raison des températures élevées, l'appareil doit être placé hors de la circulation et loin des meubles et des rideaux.

P. Hot en cours de fonctionnement. Enfants et adultes doivent être avertis des dangers de la température de surface

élevée et devrait rester à l'écart pour éviter les brûlures ou l'inﬂ ammation des vêtements.

Q. Les jeunes enfants doivent être surveillés quand ils sont dans la même pièce que l'appareil. Tout-petits, les

jeunes enfants et d'autres peuvent être sensibles à des brûlures de contact accidentel. Une barrière physique est

recommandé s'il ya des individus à risque dans la maison. Pour restreindre l'accès à une cheminée ou un poêle,

installer une barrière de sécurité pour garder les tout-petits, les jeunes enfants et d'autres personnes à risque hors

de la salle et à l'écart des surfaces chaudes.

R. Les vêtements ou autres matériaux inﬂ ammables ne doivent pas être placés sur ou près de l'appareil. Ne placez

jamais les combustibles solides, liquides inﬂ ammables, ou des objets étrangers dans cet appareil.

S. Tout écran ou grille de protection pour l'entretien d'un appareil doit être remplacé avant de faire fonctionner l'appareil.

T. Installation et réparation doit être effectuée par un technicien qualiﬁ é. L'appareil doit être inspecté avant son

utilisation et au moins annuellement par une personne un service professionnel. Un nettoyage plus fréquent peut

être nécessaire en raison des peluches provenant des tapis, literie, etc. Il est impératif que les compartiments de

contrôle, les brûleurs et les passages de circulation d'air de l'appareil être maintenu propre.

U. Seulement trousse de garniture (s) fournie par le fabricant doivent être utilisées dans l'installation de cet appareil.

Ouvertures de secours projets ne doivent pas être couverts ou bloqués. Panneaux de garniture ou entoure ne doit

pas sceller les ouvertures de ventilation dans la cheminée.

CONSERVER CES INSTRUCTIONS

5

IMPORTANT PRE-INSTALLATION AND SAFETY INFORMATION

WARNING!

A. Read all instructions. Do not install or operate this appliance without ﬁ rst reading and understanding this

manual. Failure to follow the instructions in this manual will result in an improperly installed and operating

appliance, void the warranty, and can be dangerous.

B. Improper installation, adjustment, alteration, service, maintenance, or use can cause serious injury, death or

property damage. Refer to this manual. For assistance or additional information consult a qualiﬁ ed professional

service technician, service agency or the gas supplier.

C. Provisions for adequate combustion and ventilation air must be maintained. See the VENTING REQUIREMENTS

section for details.

D. Electrical Grounding Instructions - This appliance is equipped with a three-prong (grounding) plug for your

protection against shock hazard and should be plugged directly into a properly grounded three-prong

receptacle. Do not cut or remove the grounding prong from this plug.

E. Failure to position the parts in accordance with this manual or failure to use only parts speciﬁ cally approved

with this appliance may result in property damage or personal injury.

F. Installation, service, and repair must be done by a qualiﬁ ed professional service technician.

G. A local building inspector should review your plans prior to installation.

H. Use extreme caution whenever handling this product and its accessories as they have sharp edges that can

cause personal injury.

I. It is recommended that smoke detectors are installed in the home. If possible, install a detector in a hallway

adjacent to the room (to prevent a false alarm from the heat of the appliance). However, you must follow the

requirements of the local code.

J. Any modiﬁ cation or alteration may void the warranty, certiﬁ cation and listings of this appliance.

K. Adequate accessibility clearances for servicing and proper operation must be provided.

L. Adequate clearance around air openings into the combustion chamber must be maintained.

M. This gas appliance must not be connected to a chimney ﬂ ue serving a separate solid-fuel burning appliance.

N. Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been

under water.

O. Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

P. Hot while in operation. Children and adults should be alerted to the hazards of high surface temperature and

should stay away to avoid burns or clothing ignition.

Q. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,

young children and others may be susceptible to accidental contact burns. A physical barrier is recommended

if there are at-risk individuals in the house. To restrict access to a ﬁ replace or stove, install an adjustable safety

gate to keep toddlers, young children and other at-risk individuals out of the room and away from hot surfaces.

R. Clothing or other ﬂ ammable material should not be placed on or near the appliance. Never place solid fuels,

ﬂ ammable liquids, or foreign objects into this appliance.

S. Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

T. Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected before

use and at least annually by a professional service person. More frequent cleaning may be required due to

excessive lint from carpeting, bedding material, et cetera. It is imperative that control compartments, burners

and circulating air passageways of the appliance be kept clean.

U. Only trim kit(s) supplied by the manufacturer shall be used in the installation of this appliance. Draft relief

openings must not be covered or blocked. Trim panels or surrounds must not seal ventilation openings in

the ﬁ replace.

SAVE THESE INSTRUCTIONS

6

NOTES PAGE

Please use this page to record any information that you may want to have at hand.

7

LISTING AND CODE APPROVALS

LISTING

This direct vent insert has been certiﬁ ed to:

VENTED GAS FIREPLACE HEATER ANSI Z21.88, CSA 2.33

It has been certiﬁ ed for use with either natural or propane gas, and is approved for installation in bedrooms and

aftermarket manufactured (mobile) homes.

CODE REQUIREMENTS

A. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

B. Ensure clearances are in accordance with local installation codes and the requirements of the gas supplier.

Dégagement conforme aux codes d’installation locaux et aux exigences du foumisseunde gaz.

C. A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable,

the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped

Recreational Vehicles and Mobile Housing, CSA Z240.4.

D. The appliance, when installed, must be electrically grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code,

CSA C22.1.

E. To comply with certiﬁ cation, and building code acceptances, and for safe operation and proper performance

of this appliance, use ONLY Peterson parts and accessories. Use of other controls, parts, and accessories

that are not designed for use with Real Fyre direct vent inserts is prohibited and will void all warranties,

certiﬁ cations, and building code approvals, and may cause property damage, personal injury, or loss of life.

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

This appliance is approved for installation in the state of Massachusetts subject to the following requirements:

A. Install this appliance in accordance with 248 C.M.R., the Rules and Regulations Governing Plumbers and

Gas Fitters.

B. The installer or service agent must be a plumber or gas ﬁ tter licensed in the Commonwealth of Massachusetts.

C. The ﬂ exible gas line connector used must not exceed 36 inches (92 centimeters) in length.

D. The individual manual shut-off must be a T-handle type valve, listed and approved by the state of Massachusetts.

8

SPECIFICATIONS AND DIMENSIONS

Fig. 8-2 Side View

F

G

Fig. 8-1 Top View

A

B

C

D

E

Description

Dimension

25 series 30 series 36 series

A. Unit Rear Width 21" 22" 24

1

/

2

"

B. Unit Front Width 30

3

/

8

" 34

3

/

4

" 37

5

/

8

"

C. Unit Depth 14

1

/

2

" 16

7

/

8

" 17

5

/

8

"

D. Vent Depth - Intake 12" 14

1

/

2

" 14

1

/

2

"

E. Vent Depth - Exhaust 7

7

/

8

" 10

1

/

4

" 10

1

/

4

"

F. Unit Rear Height 15

3

/

4

" 18

3

/

4

" 22"

G. Unit Front Height 19" 22" 25

1

/

2

"

Table 1 - Unit Dimensions

9

SPECIFICATIONS AND DIMENSIONS (cont.)

Fig. 9-1 Front View (3 sided surround model) Fig. 9-2 Front View (4 sided surround model)

B

A

Fig. 9-3

Side View

C

DD

E

B

A

C

DD

C

Description

ABCDE

25 series

Surround 3-sided, small 34

3

/

8

" 22

1

/

2

"5" 4

3

/

4

"1

1

/

2

"

Surround 3-sided, medium 37

3

/

8

" 25

1

/

4

"7

3

/

4

"6

1

/

4

"1

1

/

2

"

Surround 3-sided, large 40

3

/

8

" 28" 10

1

/

2

"7

3

/

4

"1

1

/

2

"

Surround 4-sided, small 34

3

/

8

" 27" 4

3

/

4

"4

3

/

4

"1

1

/

2

"

Surround 4-sided, medium 37

3

/

8

" 30" 6

1

/

4

"6

1

/

4

"1

1

/

2

"

30 series

Surround 3-sided, small 38

3

/

8

" 25

1

/

2

"5

1

/

4

"4

1

/

2

"1

1

/

2

"

Surround 3-sided, medium 41

3

/

8

" 28" 6

1

/

4

"7

1

/

2

"1

1

/

2

"

Surround 3-sided, large 44

3

/

8

" 31" 7

3

/

4

" 10

1

/

2

"1

1

/

2

"

Surround 4-sided, small 38

3

/

8

" 30" 4

3

/

4

"4

3

/

4

"1

1

/

2

"

Surround 4-sided, medium 41

3

/

8

" 33" 6

1

/

4

"6

1

/

4

"1

1

/

2

"

36 series

Surround 3-sided, small 43

3

/

8

" 30" 6" 5

3

/

4

"1

1

/

2

"

Surround 3-sided, medium 45

3

/

8

" 32" 8" 6

3

/

4

"1

1

/

2

"

Surround 3-sided, large 49

3

/

8

" 35" 11" 8

3

/

4

"1

1

/

2

"

Surround 4-sided, small 43

3

/

8

" 33" 4

1

/

2

"5

3

/

4

"1

1

/

2

"

Surround 4-sided, medium 45

3

/

8

" 36" 6" 6

3

/

4

"1

1

/

2

"

Table 2 - Surround Kit Dimensions

10

SPECIFICATIONS AND DIMENSIONS (cont.)

Fig. 10-1 Insert in Fireplace Opening

G

F

(Direct vent insert)

• F x G represents ﬁ replace opening

• Shaded area represents gap created

• Surround is designed to overlay ﬁ replace opening a

minimum of 1"

* To complete your insert installation, a matching metal surround

is required to cover the gap between the insert and your existing

ﬁ replace opening. Available in a black ﬁ nish, choose from three

ﬁ xed, non-adjustable 3-sided sizes. If your ﬁ replace opening is

raised and ﬂ ush with the wall; you may choose from two ﬁ xed

dimension 4-sided surrounds. Consult Table 3 for assistance.

(gap in ﬁ replace)

TO DETERMINE THE APPROPRIATE SURROUND FOR YOUR SETUP* :

Recommended surround

F max G max

25 series

Surround 3-sided, small 32

3

/

8

" 21

1

/

2

"

Surround 3-sided, medium 35

3

/

8

" 24

1

/

4

"

Surround 3-sided, large 38

3

/

8

" 27"

Surround 4-sided, small 32

3

/

8

" 19

3

/

4

"

Surround 4-sided, medium 35

3

/

8

" 24

1

/

4

"

30 series

Surround 3-sided, small 36

3

/

8

" 24

1

/

2

"

Surround 3-sided, medium 39

3

/

8

" 27"

Surround 3-sided, large 42

3

/

8

" 30"

Surround 4-sided, small 36

3

/

8

" 24

1

/

4

"

Surround 4-sided, medium 39

3

/

8

" 25

3

/

4

"

36 series

Surround 3-sided, small 41

3

/

8

" 29"

Surround 3-sided, medium 43

3

/

8

" 31"

Surround 3-sided, large 47

3

/

8

" 34"

Surround 4-sided, small 41

3

/

8

" 27

1

/

2

"

Surround 4-sided, medium 43

3

/

8

" 29"

Table 3 - Recommended Surround (based upon ﬁ replace opening, see Fig. 10-1)

11

SPECIFICATIONS AND DIMENSIONS (cont.)

Fig. 11-1 Minimum Fireplace Dimensions

A

B

C

D

* For elevations above 2,000 feet, the BTU rate of the unit is reduced by

4% for each additional 1,000 feet. To install the unit above an elevation of

2,000 feet, you must use proper oriﬁ ces based on the de-rated BTU.

* If exhaust collar on direct vent insert and ﬁ replace damper

do not line up, add 3 inches to minimum ﬁ replace height

to allow offsets of vent pipe.

Description

Dimension

25 series 30 series 36 series

A. Front Width 30

1

/

2

" 35" 38"

B. Rear Width 21

1

/

2

" 22

1

/

2

" 26"

C. Depth 15

1

/

2

" 18

1

/

2

" 19

1

/

2

"

D. Height * 20" 22

1

/

2

" 26"

Table 4 - Minimum Fireplace Dimensions

Remote Transmitter

Supply voltage

3 V

(two 1.5V AAA batteries)

Ambient temperature ratings 32 - 122 °F (0-50 °C)

Radio frequency 303.8 MHz

Receiver

Supply voltage

6.0 V

(four 1.5 V AA batteries)

Ambient temperature ratings 32 - 130 °F (0-60 °C)

Radio frequency 303.8 MHz

Fan

Input voltage / frequency / current 120 V / 60 Hz / 5 A

Electronic Igniter

Supply voltage

1.5 V

(one 1.5 V AA battery)

Ambient temperature ratings 140 °F (60 °C)

Table 5 - BTU Ratings and Oriﬁ ce Sizes

Table 6 - Technical Data Speciﬁ cations

Model

Natural Gas Propane Gas

BTU

Rating

Oriﬁ ce Size

BTU

Rating

Oriﬁ ce Size

High

setting

Low

setting

Front Rear

High

setting

Low

setting

Front Rear

25 series

(0-2000 FT)

* 25k 17k #42 - 20k 15k #55 -

30 series

(0-2000 FT)

* 32k 23k #50 #45 29k 23k #59 #56

36 series

(0-2000 FT)

* 40k 30k #47 #39 33k 27k #57 #56

12

SPECIFICATIONS AND DIMENSIONS (cont.)

25 SERIES WIRING DIAGRAM

30 & 36 SERIES WIRING DIAGRAM

Fig. 12-2

Fig. 12-1

PILOT ASSY

FAN ASSY

THERMAL

DISC SENSOR

REMOTE RECEIVER

IGNITER MODULE

FAN SPEED

ADJ. KNOB

GAS TUBE

TO BURNER

VALVE ASSY

SIDE VIEW

PILOT ASSY

FAN ASSY

THERMAL

DISC SENSOR

REMOTE RECEIVER

IGNITER MODULE

3-POSITION

MODE SWITCH

GAS TUBE TO

FRONT BURNER

GAS TUBE TO

REAR BURNER

VALVE ASSY

FRONT VIEW

BLACK

3-POSITION

MODE SWITCH

VALVE ASSY

SIDE VIEW

VALVE ASSY

FRONT VIEW

VALVE

ASSY

ORANGE

RED

POWER CORD

120 VAC SUPPLY

POWER CORD

120 VAC SUPPLY

VALVE

ASSY

BLACK

ORANGE

RED

FAN SPEED

ADJ. KNOB

13

MINIMUM CLEARANCES

All minimum clearances must be met and maintained at all times. The clearances shown below include any

adjacent walls, spacers, standoffs, and any projections such as shelves, window sills, or ﬁ replace mantels. They

also include any combustible decorations/items. Any ﬁ nishing on the mantel must be heat resistant.

TOOLS REQUIRED

The following are the minimum tools required for the installation of your direct vent insert. Additional tools may

be required for your individual installation.

• 2 assemblers recommended

• rope

• measuring tape

• marker

• appropriate tools for gas supply

and electrical install

• reciprocating saw

• Mill-PAC hi temp. sealant

• cordless drill

• drill bits and drivers

• Phillips screwdriver (small & medium size)

•

5

/

16

" &

7

/

16

" nut drivers

•

7

/

16

" open-end wrench

• utility knife

• tin snip / hacksaw

Fig. 13-1 Minimum Clearances

A

B

C

Mantel - 12" Depth

Combustible Trim or Mantel Depth of 8" or less

FRONT VIEW TOP VIEW

D

SIDE VIEW

8"

12"

B

C

Table 7 - Minimum Clearances

Description

Dimension

25 series 30 series 36 series

A. Clearance required from the side edge of

the insert to combustibles or side wall

7" 7" 7"

B. Clearance required from the top edge of

the insert to combustibles or 8" mantel

16" 16" 16"

C. Clearance required from the top edge of

the insert to combustibles or 12" mantel

22" 22" 22"

D. Clearance required in front of insert to

allow door to fully open

35" 39" 44"

14

REPLACEMENT PARTS LIST

Robert H. Peterson Co. • 14724 East Proctor Avenue, • City of Industry, CA 91746

IMPORTANT

Remove all packing

material (including any

protective coatings) and

discard prior to use.

Your direct vent insert is

shipped in 4 boxes:

• Insert

• Firebox liners

• Surround

• Log set

Replacement parts can be

ordered from your local

Real Fyre dealer.

SHARP

EDGES

USE CAUTION

25 SERIES

16

8

5

17

24

25

19

14

11

10

12

1

18

21

15

4

9

2

6

7

22

15

REPLACEMENT PARTS LIST (cont.)

25 SERIES

Item Description Part No. Qty.

1. Control valve (Nat) DV-30-721 1

or Control valve (LP) DV-30-722 1

2. Burner assembly DV-25-703 1

3. Burner oriﬁ ce (Nat)* 3001-42-1 1

or Burner oriﬁ ce (LP)* 3001-55-1 1

4. Pilot assembly (Nat) DV-25-725 1

or Pilot assembly (LP) DV-25-726 1

5. Fan assembly DV-30-736 1

6. Thermal disc sensor TS-3 1

7. Grate DV-25-707 1

8. Glass panel assembly DV-25-900 1

9. Top ﬁ rebox liner DV-25-918 1

10. Fan speed adjustment knob KNOB-11 1

11. Igniter module OCR-34-21 1

12. 3-position mode switch

SW-14 1

13. Switch wire harness * WH-06 1

14. Lintel DV-25-902 1

15. Spring door latch DV-30-910 2

16. Remote transmitter AT-R2-1 1

17. Remote receiver RR-2A 1

18. Air ﬂ ow screen DV-25-711 1

19. Support leg (set of 4) DV-30-911 1

20. Wire harness kit* WI-3 1

21. Vent adapter plate DV-25-912 1

22. Retention bracket DV-25-919 1

23. Wire hook* DV-30-717 1

24. Glowing embers EM-10 1

25. Bryte coals EM-11 1

*

Not shown

16

Robert H. Peterson Co. • 14724 East Proctor Avenue, • City of Industry, CA 91746

IMPORTANT

Remove all packing

material (including any

protective coatings) and

discard prior to use.

Your direct vent insert is

shipped in 4 boxes:

• Insert

• Firebox liner

• Surround

• Log set

Replacement parts can be

ordered from your local

Real Fyre dealer.

30 model shown

SHARP

EDGES

USE CAUTION

REPLACEMENT PARTS LIST (cont.)

30 & 36 SERIES

21

18

19

13

1

12

14

8

20

9

10

7

29

28

26

3

27

6

2

23

17

11

16

24

17

REPLACEMENT PARTS LIST (cont.)

30 SERIES 36 SERIES

Item Description Part No. Qty. Part No. Qty.

1. Control valve (Nat) DV-30-721 1 DV-30-721 1

or Control valve (LP) DV-30-722 1 DV-30-722 1

2. Front burner assembly DV-30-703 1 DV-36-703 1

3. Rear burner assembly DV-30-704 1 DV-36-704 1

4. Front burner oriﬁ ce (Nat)* 3001-50-1 1 3001-47-1 1

or Front burner oriﬁ ce (LP)* 3001-59-1 1 3001-57-1 1

5. Rear burner oriﬁ ce (Nat)* 3001-45-1 1 3001-39-1 1

or Rear burner oriﬁ ce (LP)* 3001-56-1 1 3001-56-1 1

6. Pilot assembly (Nat) DV-25-725 1 DV-25-725 1

or Pilot assembly (LP) DV-25-726 1 DV-25-726 1

7. Fan assembly DV-30-736 1 DV-30-736 1

8. Thermal disc sensor TS-3 1 TS-3 1

9. Grate DV-30-707 1 DV-36-707 1

10. Glass panel assembly DV-30-900 1 DV-36-900 1

11. Top ﬁ rebox liner DV-30-918 1 DV-36-918 1

12. Fan speed adjustment knob KNOB-11 1 KNOB-11 1

13. Igniter module OCR-34-21 1 OCR-34-21 1

14. 3-position mode switch SW-14 1 SW-14 1

15. Switch wire harness * WH-06 1 WH-06 1

16. Lintel DV-30-902 1 DV-36-902 1

17. Spring door latch DV-30-910 2 DV-30-910 2

18. Remote transmitter AT-R2-1 1 AT-R2-1 1

19. Remote receiver RR-2A 1 RR-2A 1

20. Ember screen DV-30-710 1 DV-30-710 1

21. Support leg (set of 4) DV-30-911 1 DV-30-911 1

22. Wire harness kit* WI-3 1 WI-3 1

23. Vent adapter plate DV-30-912 1 DV-30-912 1

24. Retention bracket DV-25-919 1 DV-25-919 1

25. Wire hook* DV-30-717 1 DV-30-717 1

26. Front bafﬂ e DV-30-718 1 n/a -

27. Rear bafﬂ e DV-30-719 1 n/a -

28. Glowing embers EM-10 1 EM-10 2

29. Bryte coals EM-11 1 EM-11 2

*

Not shown

18

1

2

3

4

5

6

Boston Buff Brick

ﬁ rebox liners shown

25 SERIES 30 SERIES 36 SERIES

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

1. Left liner (Boston Buff Brick) DVP-25-800 1 DVP-30-800 1 DVP-36-800 1

or

Left liner (Herringbone Brick)

Left liner (Black Porcelainized)

DVP-25-801

DVP-25-811

1

DVP-30-801

DVP-30-811

1

DVP-36-801

DVP-36-811

1

2. Right liner (Boston Buff Brick) DVP-25-802 1 DVP-30-802 1 DVP-36-802 1

or

Right liner (Herringbone Brick)

Right liner (Black Porcelainized)

DVP-25-803

DVP-25-812

1

DVP-30-803

DVP-30-812

1

DVP-36-803

DVP-36-812

1

3. Rear liner (Boston Buff Brick) DVP-25-804 1 DVP-30-804 1 DVP-36-804 1

or

Rear liner (Herringbone Brick)

Rear liner (Black Porcelainized)

DVP-25-805

DVP-25-813

1

DVP-30-805

DVP-30-813

1

DVP-36-805

DVP-36-813

1

4. Left ﬂ oor panel DVP-25-808 1 DVP-30-808 1 DVP-30-808 1

5. Right ﬂ oor panel DVP-25-809 1 DVP-30-809 1 DVP-30-809 1

6. Front ﬂ oor panel DVP-25-810 1 DVP-30-810 1 DVP-36-810 1

REPLACEMENT PARTS LIST (cont.)

The log set is purchased and packaged separately; contact your local Real Fyre dealer

when ordering. Refer to the instructions included with the log set.

19

REPLACEMENT PARTS LIST (cont.)

25 SERIES 30 SERIES 36 SERIES

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

1.

or

3-sided surround assembly, small

3-sided surround assembly, medium

3-sided surround assembly, large

DVS-25-3A

DVS-25-3B

DVS-25-3C

1

DVS-30-3A

DVS-30-3B

DVS-30-3C

1

DVS-36-3A

DVS-36-3B

DVS-36-3C

1

2. Surround screen DV-25-913 1 DV-30-913 1 DV-36-913 1

3. 3-sided surround door DV-25-914 1 DV-30-914 1 DV-36-914 1

4.

or

3-sided surround fascia, small

3-sided surround fascia, medium

3-sided surround fascia, large

DV-25-915A

DV-25-915B

DV-25-915C

1

DV-30-915A

DV-30-915B

DV-30-915C

1

DV-36-915A

DV-36-915B

DV-36-915C

1

5.

or

4-sided surround assembly, small

4-sided surround assembly, medium

DVS-25-4A

DVS-25-4B

1

DVS-30-4A

DVS-30-4B

1

DVS-36-4A

DVS-36-4B

1

6. Surround screen DV-25-913 1 DV-30-913 1 DV-36-913 1

7. 4-sided surround door DV-25-916 1 DV-30-916 1 DV-36-916 1

8.

or

4-sided surround fascia, small

4-sided surround fascia, medium

DV-25-917A

DV-25-917B

1

DV-30-917A

DV-30-917B

1

DV-36-917A

DV-36-917B

1

2

3

4

5

6

7

8

20

INSTALLATION REQUIREMENTS

Installation must be done by a qualiﬁ ed professional service technician.

Prior to installation ensure that all speciﬁ cations, dimensions, and minimum clearances stated in this

manual are observed. You must read all warnings and safety information, and understand all of the

information in this manual. All of these installation requirements must be observed and met.

FIREPLACE REQUIREMENTS

A. This appliance must be vented directly to the outside in accordance with the current edition of the National

Fuel Gas Code (NFPA 54 in U.S.A. and CAN/CSA B149.1 in Canada) and must never be attached to a

chimney serving a separate solid fuel burning appliance. This appliance is designed to be installed into an

existing masonry ﬁ replace (built to UBC 37 or ULC S628 standards) or factory built solid fuel, wood, burning

ﬁ replace (listed to UL 127 or ULC S610) only. All exhaust gases must be vented outside the structure.

Combustion air is drawn from outside the structure.

B. Cutting any sheet metal parts of the ﬁ replace in which the gas ﬁ replace insert is to be installed is prohibited,

with the exception of the ﬁ rebox ﬂ oor. The metal ﬁ rebox ﬂ oor may be removed/altered to allow additional

room for installation of the insert. Note: a minimum 5" clearance is required between the ﬁ replace ﬂ oor and

the insert. The clearance may be provided by lowering the ﬁ rebox ﬂ oor, placing bricks, etc. See Fig. 20-2.

C. If the factory-built ﬁ replace has no gas access hole(s) provided, an access hole of 1.5 in (37.5 mm) or less

may be drilled through the lower sides or bottom of the ﬁ rebox in a proper workmanship like manner. This

access hole must be plugged with non-combustible insulation after the gas supply line has been installed.

Si le foyer préfabriqué ne comporte pas d’oriﬁ ces d’amenée du gaz, un oriﬁ ce d’au plus 37,5 mm (1,5 po)

peut être pratiqué, selon les règles de l’art, dans la partie inférieure des parois ou au fond de la chambre

de combustion. Cet oriﬁ ce doit être obturé au moyen d’isolant incombustible une fois la conduite de gaz

en place.

D. The ﬁ replace ﬂ ue damper must be removed for installation of the gas ﬁ replace insert.

E. The ﬁ replace and ﬁ replace chimney must be completely clean. Brush and vacuum all interior surfaces so

that no embers, soot, or loose combustion deposits can be drawn into the heat circulation fan and blown

into the living area. The ﬁ replace and ﬁ replace chimney must be in good working order and constructed of

non-combustible materials. Inspect chimney clean-outs for proper ﬁ t and seal. If any portion of the chimney

system shows signs of structural or mechanical weaknesses, the faulty portion must be repaired or replaced

prior to installing this appliance.

F. Firebox liners, glass panels, screen rails, screen mesh and log grates may be removed from the ﬁ replace

(as needed) before installing the gas ﬁ replace insert. Smoke shelves, shields and bafﬂ es may be removed

if attached by mechanical fasteners. Any parts that are removed must be retained for later reinstallation to

restore the ﬁ replace to its original operating condition. The removal of any part must not alter the integrity

of the outer shell of the pre-fab ﬁ replace cabinet in any way. If any parts are removed (or altered) from the

existing ﬁ replace, a Warning Label (see Fig. 20-1 below) must be afﬁ xed inside the ﬁ replace ﬁ rebox. The

label must be visible upon removal of the direct vent insert.

Fig. 20-1 Fireplace Warning Label (see F above)

WARNING

THIS FIREPLACE HAS BEEN ALTERED

TO ACCOMODATE A FIREPLACE INSERT

AND SHOULD BE INSPECTED BY A QUALIFIED PERSON

PRIOR TO RE-USE AS A CONVENTIONAL FIREPLACE.

Fig. 20-2 Pre-fab ﬁ replace ﬂ oor height adjustment

Pre-fab

ﬁ replace

Fireplace

ﬂ oor

Insert resting

at new

lowered level

(i.e. lowering of

ﬂ oor, placing

bricks, etc.)

Combustible

ﬂ oor

Min. 5"

clearance

La page charge ...

Real Fyre DVI Direct Vent Mode d'emploi

Ce manuel convient également à

Real Fyre DVI Direct Vent Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents