Genie ISL950 Manuel utilisateur

Marque: Genie

Modèle: ISL950

Catégorie: Porte de garage

Taper: Manuel utilisateur

3511035556

Included Wall Control MUST be installed prior to operation of this Garage

Door Operator

Safe-T-Beam

Safety Reverse System Must be installed to close door

SAVE THIS MANUAL FOR FUTURE REFERENCE

NOTE: Your Residential Operator comes with a Rail Assembly

which is standard for up to a 7 foot 6 inch high door. An extension

kit for an 8 foot high door is available.

For Answers and Assistance:

1.800.354.3643

or visit www.geniecompany.com

Series

IS, ISL, IC, H

Includes Remote Control

and SERIES II Electronics

Things to consider if you are planning to “do-it-yourself.”

Whether you are replacing an existing garage door operator or installing an operator in your

garage for the first time, there are some pre-installation issues which need to be addressed.

They are as follows:

The Genie Company recommends that you read and fully understand all

information and instructions contained herein before choosing a “do-it-yourself”

installation. Any questions should be directed to the Genie Company or an authorized

Genie Dealer.

To avoid damage to your door and/or

operator, make sure you disable any door

locks prior to installing your operator

PRE-INSTALLATION CHECK LIST

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

Check your ceiling where the power

head of your new unit will be mounted.

Plan how you will be mounting the power head.

It is possible that ceiling joists may not be in the

exact position needed with respect to the garage

door operator. It may be necessary to add an

additional bracket and

fasteners (not included

with your new door operator kit).

Check the wall directly above the garage

door

. The door operator’s header bracket

must be securely fastened to this wall. Ensure

that the structure will provide a strong mounting

location.

Check to see if the mounting location

for the Safe-T-Beam

System (STB) is

clear from obstruction and has a wood

surface available for attaching the STB brack-

ets

. The brackets may be attached to concrete if

necessary but extra tools and special fasteners

(not supplied) will be required.

NOTE: 1-1/2" STB bracket adapters are

available through your local Genie Dealer.

Is your garage door made of

light-weight steel, aluminum, fiberglass

or glass panels

? Additional support bracing

must be added to these type doors. If this is the

case, please contact the door distributor or

manufacturer so that they can furnish you with a

“bracing kit.”

Ensure that your door is properly balanced

and moving freely. SEE WARNING BELOW.

If your door sticks, binds, or is out of

balance, have it adjusted by a professional.

Door springs, cables, pulleys, brackets and

associated hardware are under extreme

tension and can cause serious injury or

death.

WARNING

(

The issue numbers below refer to the circled numbers in the illustrations on page 3.

)

(NOT SHOWN) If your garage does not have

a separate entry door, you should consider

an emergency release kit

(

GER-2

)

for installation

on your garage door. See page C at the center of

this manual.

DO NOT USE AN EXTENSION CORD!

Extension cords can cause dangerous

overheating conditions.

DO NOT USE A PORTABLE GENERATOR!

This product is designed to operate on

standard house current. Do not use

alternate power supplies.

WARNING

You need a 110-120 Volt power supply

available

. The outlet should be no more than

3 feet from the power head once it is mounted. (The

cord is 4 ft. in length.) SEE WARNING BELOW.

HomeLink® is a universal

transceiver (a combined

transmitter and receiver), that provides a

convenient way to replace up to three hand-held

radio-frequency (RF) transmitters used to

activate devices such as gate operators, garage

door openers, entry door locks, security systems

and even home lighting. Additional HomeLink

information can be found at: www.homelink.com

or by calling 1.800.355.3515

TYPICAL SECTIONAL DOOR INSTALLATION

TYPICAL

SUPPORT

BRACKET

EXTENSION SPRING

TORSION SPRING

SAFE-T-BEAM

BRACES

ADDED

HEADER BRACKET

MOUNTING BOARD

36” POWER CORD

120V GROUNDED

OUTLET

SECTIONAL DOOR

1-PIECE DOOR

TYPICAL 1-PIECE

DOOR INSTALLATION

Safe-T-Beam

(STB) Non-Contact Reversing System

Places an invisible beam across door opening that reverses the door during down travel to the fully open

position if anything passes through beam.

Safe-T-Reverse

Contact Reversing System

Automatically stops and reverses a closing door within 2 seconds of contact with an object.

Safe-T-Stop

Timed Reversed System

Automatically opens a closing door, if door does not close within 30 seconds.

Force Guard

Control

Used to set the force required for opening and closing door. For maximum safety, set the minimum force

required to fully open and close door.

Automatic Lighting System

Two light bulbs up to 60 Watts max. each are used for safer entries and exits.The light turns on when door is

activated and automatically turns off 4.5 minutes later.

Manual Emergency Release

Allows the garage door to be opened or closed manually for emergencies or maintenance.

SAFETY FEATURES

(

varies by model

)

TABLE OF CONTENTS

SECTION PAGE

PRE-INSTALLATION CHECK LIST . . . . . . . . . . . . . . . . 2-3

TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

OPERATIONAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PARTS LISTS AND ILLUSTRATIONS . . . . . . . . . . . . . . . . . 5-8

POWER HEAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ONE-PIECE RAIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

THREE-PIECE RAIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

FASTENERS AND ACCESSORIES . . . . . . . . . . . . . . . . . . 8

SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PRE-INSTALLATION WARNING. . . . . . . . . . . . . . . . . . . . . . . . 9

1MAIN ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 10-14

2INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-21

3 SAFE-T-BEAM

. . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

4WALL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25

5 LIGHT & LIGHT LENS. . . . . . . . . . . . . . . . . . . . . . . . . 25

6 CONNECTING POWER . . . . . . . . . . . . . . . . . . . . . . . . 26

7 SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-28

CONTACT REVERSE. . . . . . . . . . . . . . . . . . . . . . . 28

8BATTERY & VISOR CLIP. . . . . . . . . . . . . . . . . . . . . . . 28

9PROGRAMMING REMOTE CONTROLS . . . . . . . . . . 29

TRANSMITTER COMPLIANCE STATEMENT . . . . . . . . . . . . 30

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . 30

10 MAINTENANCE & TROUBLESHOOTING . . . . . . . 31-32

11 WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . A

WARRANTY B

ACCESSORIES ORDER FORM. . . . . . . . . . . . . . . . . . . . . . . . C

RECOMMENDED TOOLS

5/32" Drill Bit

7/16" and 9/16" Sockets

Step ladder

Drill

Ratchet

Carpenter’s level

Pencil

Tape measure

Wire strippers

Phillips screwdriver

Adjustable wrench

POWER HEAD EXPLODED VIEW

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

Power Head Assembly

[

]

Item Part Name

1Power Head Assembly

ACover (By Series/Model)

B Front Plate Assembly

C Light Socket

D Motor Parts

E Receiver Assembly

F Capacitor (By Series/Model)

G Opto Wheel

HOpto-Luctor Assembly

J Sequencer Assembly

KCircuit Board Bracket

LTransformer

POWER HEAD PARTS LIST

Item Part Name

MTerminal Strip

NNo. 8-32 x 1/2" Hex Washer Head Screw

PNo. 8-32 x 3/8" Slot Hex Washer Head Screw

RCapacitor Isolator

45 Bumper

4 1/4-20 Shoulder Bolt

5 1/4" Flange Nut

39 Coupler

41 No. 8-32 x 3/8" Phillips Hex Head Screw

42 No. 8-32 x 3/8" Phillips Pan Head Screw

48 Mounting Straps

49 Light Lens

OPERATIONAL FEATURES

INTELLICODE

Access Security System

Improves security of door operator by continuously changing the access code each time the remote control is

used.The door operator responds to each new code only once. An access code copied from a working system

and tried again will not control the door operator.

INTELLICODE

1-Button Remote Control

Controls door operator by allowing the garage door to be opened and closed remotely.

INTELLICODE

Multi-Button Remote Control

Operates multiple Intellicode

equipped door operators.

Lighted Wall Button (some models)

Operates door operator from inside garage. DO NOT use with lighted wall console.

Wall Console (some models)

Works like a lighted wall button but includes a Vacation Lock Switch that disables all controls. LED indicator

shows whether system is powered, locked or unlocked. Makes console easy to find in dark. Controls door

opener from inside garage. Independent light control allows convenient manual control of the Automatic Lighting

System. DO NOT use with lighted wall button.

NOTE: All items may not be supplied with your garage door operator.

1-PIECE RAIL HARDWARE EXPLODED VIEW

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

1-Piece Rail & Screw Assembly

[

]

NOTE:The operator will not function properly unless the Safe-T-Beam

sensors are installed and the force controls adjusted.

15B

2224

15A

Item Part Name

Parts Required

1 Piece 3-Piece

1 Power Head Assembly (See page 5) 1 1

2 Rail Assembly (1 piece) 1

3 Rail Assembly (3 piece) 1

3A First Rail Section 1

3B Middle Rail Section 1

3C End Rail Section 1

4 1/4-20 Hex Hd Shoulder Bolt 2 2

5 1/4"-20 Hex Flange Nut 2 2

6 Carriage Stop 1 1

7 Rail Clamps 4

8 5/16" Hex Shoulder Bolt 8

9 5/16" Hex Flange Nut 5 13

10 Carriage Assembly 1 1

11 Collar 2

12 Retaining Clip 2

13 Rail Strap 1 1

15A Open Limit Switch Assembly (Grey) 1 1

PARTS LIST

Item Part Name

Parts Required

1 Piece 3-Piece

15B Close Limit Switch Assembly (Brown) 1 1

16 No. 8-32 x 3/8" Hex Head Screw 2 2

17 Emergency Release Cord 1 1

18 Emergency Release Knob 1 1

19 Emergency Release Tag 1 1

20 Header Bracket 1 1

21 Door Bracket 1 1

22 1/4" x 2" Lag Screw 8 8

23 Straight Door Arm 1 1

24 Clevis Pin 2 2

25 Cotter Pin 2 2

26 Curved Door Arm 1 1

27 3/8" x 7/8" Hex Head Bolt 2 2

28 3/8" Hex Flange Nut 2 2

29 Wire 95ft 95ft

30 Insulated Staple 30 30

31 Wall Button varies varies

PARTS LIST

3-PIECE RAIL HARDWARE EXPLODED VIEW

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

3-Piece Rail & Screw Assembly

[

]

NOTE:The operator will not function unless the Safe-T-Beam

system is

installed and the force controls are properly set.

15B

15A

Item Part Name

Parts Required

1 Piece 3-Piece

33 Wall Console varies varies

34 #6 x 1-1/4” Pan Head Screw 2 2

35 Entrapment WARNING Label 1 1

36 Safe-T-Beam (STB) System Sensor (Green LED) 1 1

37 Safe-T-Beam (STB) System Source (Red LED) 1 1

38 Safe-T-Beam (STB) System Bracket 2 2

39 Coupler 1 1

40 No. 10 x 11/4" Phillips Hex Head Screw 4 4

41 #8 x 3/8” Hex Head Screw 4 4

42 #8 x 3/8” Pan Head Screw 2 2

43 Safety & Maintenance Guide 1 1

44 Wire Clip 4 4

45 Bumper 1 1

46 5/16" x 3/4" Hex Head Bolt 5 5

47 1/4-20 x 3/4” Self-tapping Screw 3 3

48 Mounting Straps 2

49 Light Lens (Shown on page 5) 1 1

50 Remote Control varies varies

PARTS LIST

NOTE: Accessories vary by model.

FASTENERS - Shown full size. See Parts List for description.

Cotter pin

Clevis pin

PARTS IDENTIFICATION FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

remotes

vary

by model

Rubber bumper

1/4" x 2" Lag screw

5/16" Flange nut

3/8" Hex head bolt

3/8" Nut

#10 x 1-1/4" Phillips hex head screw

1/4" Flange nut

Insulated staple

Coupler

#8-32 x 3/8" Hex head screw

Collar

5/16" Shoulder bolt w/flange

5/16" x 3/4" Hex head bolt

1/4" Shoulder bolt w/flange

1/4"-20 Self-drilling screw

#6 x 1-1/4" Pan head screw

Clip

Wire clip

#8 x 3/8" Pan head screw

#8 x3/8" Hex flange head screw

Carriage stop (not to scale)

WARNING

Garage doors are large, heavy objects that move with the help of springs

under high tension and electric motors. Since moving objects, springs under

tension, and electric motors can cause injuries, your safety and the safety of

others depend on you reading the information in this manual. If you have

questions or do not understand the information presented, call your nearest

service representative.

In this section and those that follow, the words Danger,Warning, and

Caution are used to emphasize important safety information.

The word:

DANGER means that severe injury or death will result from failure

to follow instructions.

WARNING means that severe injury or death can result from failure

to follow instructions.

CAUTION means that property damage or injury can result from

failure to follow instruction.

The word NOTE is used to indicate important steps to be followed

or important considerations.

OVERVIEW OF

POTENTIAL HAZARDS

POTENTIAL

HAZARD

EFFECT PREVENTION

Keep people clear of opening while door is

moving.

Do Not allow children to play with the door

operator.

Do Not operate a door that jams or one that

has a broken spring.

MOVING

DOOR

WARNING:

Can Cause

Serious Injury

or Death

Turn off power before removing operator cover.

When replacing cover, make sure wires are not

pinched or near moving parts.

Operator must be properly grounded.

ELECTRICAL

SHOCK

WARNING:

Can Cause

Serious Injury

or Death

Do Not try to remove, repair or adjust springs

or anything to which door spring parts are

fastened, such as, wood blocks, steel

brackets, cables or other like items.

Repairs and adjustments must be made by a

trained service person using proper tools and

instructions.

HIGH

SPRING

TENSION

WARNING:

Can Cause

Serious Injury

or Death

IMPORTANT

INSTALLATION

INSTRUCTIONS

To reduce the risk of

severe injury or death:

WARNING

SAFETY INFORMATION PRE-INSTALLATION WARNING

SAVE THESE INSTRUCTIONS

Visit our website at:

www.geniecompany.com

FILL THIS IN AT TIME OF INSTALLATION FOR YOUR OWN

RECORDS, SO THAT IT WILL

BE AVAILABLE IF YOU EVER NEED TO CALL US.

Date Purchased _____/_____/_____

Serial Number _____/____/_______________________________

Operator Model _______________________________________

Dealer Name __________________________________________

Dealer Address _______________________________________

City _________________________________________________

State ________________________________________________

Zip _____________________

WK YY PI

MM DD YY

(See Fig. 1-1)

1. READ AND FOLLOW ALL SAFETY,

INSTALLATION AND OPERATION

INSTRUCTIONS. If you have any questions

or do not understand an instruction, call your

service representative.

2. Do Not install Opener on an improperly

balanced door. An improperly balanced

door may cause severe injury. Repairs and

adjustments to cables, spring assemblies,

and other hardware must be made by a

trained service person using proper tools

and instructions.

3. Remove all handles and ropes, and

disable all locks connected to the door

before installing the Opener.

4. Install door Opener 7' or more above

the floor. Mount the emergency release

knob 6' above the floor.

5. Do Not connect the Opener to the

power source until instructed to do so.

6. Locate the Wall Control:

• Within sight of the garage door.

• At a minimum height of 5', so small

children cannot reach it.

• Away from all moving parts of the

garage door.

7. Install the entrapment WARNING label

next to the wall button or console. Install

the emergency release tag on the

emergency release.

8. The operator must reverse when the door

contacts a 1

" high object on the floor at

the center of the doorway.This is the size of

a 2” x 4” board laid flat.

NOTE: Please keep original or photocopy of your

sales receipt with this manual for future reference

should service ever be required.

SECT 1—MAIN ASSEMBLY

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

1. Set power head so that front panel (with end

of shaft and rail attachment flange) is facing up.

Fig. 1-1.

NOTE: If you have this type Carriage Stop, skip

Step 2. DO

NOT install Bumber.

2. Install bumper [45].

•Peel protective paper from glue side

of bumper.

• Stick bumper into position as shown.

Fig. 1-1.

3. Install coupler [39].

• Place coupler over end of shaft.

•Turn it as needed until it engages with shaft.

(It will drop down over end of shaft and will

no longer turn freely. Fig. 1-1.

4. Set power head on its bottom. Fig. 1-4.

5. Attach 1-piece rail or “first” rail section[3A]

of 3-piece rail to power head.

• (3-piece only)Select “first” rail section. (It has

protective cardboard sleeve over end of

screw.) Fig. 1-2.

• (3-piece only) Remove cardboard sleeve.

• Slide end of screw out about 5 inches.

Fig. 1-3.

• Place bearing end of screw against coupler.

Fig. 1-4.

•Turn screw until it engages with coupler.

• Slide rail section into rail attachment flange

until holes in rail match up with holes

in flange.

• Secure “first” rail section with 2 bolts [4] and

2 nuts [5], hand

tight only. Fig. 1-5.

• For 1-piece rail, skip to step 8.

bumper

coupler

Fig. 1-1

Fig. 1-2

Fig. 1-3

Fig. 1-4

Drive screws can slide out of rail sections.

Keep rail sections level until operator is

fully assembled.

CAUTION

NOTE: 3-piece rail assembly is for doors up to

and including 7 feet 6 inches high. An extension

for 8 feet doors is available.

OPEN BLUE PARTS BAG

Rubber bumper

Coupler

[

]

[

]

serial no.

MAIN ASSEMBLY

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

6. Attach “middle” rail section [3B].

• Select “middle” rail section. (This section

looks identical on both ends with each set of

holes being about 4 inches apart.) Fig. 1-6.

•Find arrows stamped into side of rail.

Fig. 1-7.

• Align rail so arrows point away from

power head.

• Slide screw toward power head so it sticks

out end of rail section about 2 inches.

Fig. 1-5

Fig. 1-6

Fig. 1-7

1/4" Flange nut

1/4" Shoulder bolt w/flange

[

]

[

]

end rail section

middle rail section

MAIN ASSEMBLY

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

• Slide a collar [11] over exposed end of

screw on “middle” rail as far as it will go.

Fig. 1-8.

• Engage “hook” on “middle” rail with “hook”

on “first” rail section. Fig. 1-9.

• Slide collar toward power head so that it

now covers hooks. Fig. 1-10.

• Snap a clip [12] onto screw behind collar to

hold collar in place. Fig. 1-11.

• Slide middle rail against first rail.

• Place rail clamp [7] on each side of joint

where rails meet. Match up holes in clamps

with holes in rail. (Edge with lip is bottom

of clamp.)

• Secure rail clamps with 4 bolts [8] and 4

nuts [9], hand

tight only. Fig. 1-12.

Fig. 1-8

Fig. 1-9

Fig. 1-10

Fig. 1-11

clip

Fig. 1-12

5/16" Flange nut

5/16" Shoulder bolt w/flange

[

]

[

]

Collar

Clip

[

]

[

]

rail clamp

slide collar

MAIN ASSEMBLY

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

NOTE: If installing an extension kit for an

8 feet high door, refer to the instructions

included with the extension kit now.

7. Attach “end” rail section [3C].

• Attach “end” rail in same way as “middle” rail

(step 5). (“End” rail section screw has “hook”

on one end only.)

8. Flip power head/rail assembly over (upside

down), so that entire length of screw is visible

from above.

9. Install carriage stop [6].

• With bent tabs facing up, slide carriage stop

into rail. Fig. 1-13.

• Slide carriage stop along rail until it rests

against power head.

10.Install carriage [10].

• Place emergency release lever in released

position. Fig. 1-14.

• Make sure arrow on side of carriage

(Fig. 1-14) is pointing away from power

head. (Emergency release lever will be

facing power head.)

• Slide carriage into rail. Fig. 1-15.

NOTE: Carriage can be used as a temporary

support for the rail while performing the next few

steps of assembly. Slide carriage to mid point of

rail. Place emergency release lever in engaged

position.

11.Flip assembly right side up.

(Rail resting on carriage.)

12. Attach rail strap

[13]

• Place rail strap against end of rail so that

attached stud passes in front of end of rail.

Fig. 1-16.

•Line up rail strap holes with rail holes.

• Secure with 2 bolts [46] and 2 nuts [9].

13. Make sure rail assembly is resting straight

and level.

•FULLY TIGHTEN ALL BOLTS AND NUTS IN

RAIL ASSEMBLY.

Fig. 1-13

Fig. 1-14

engaged

released

arrow

Fig. 1-15

power

head

carriage stop

carriage

Fig. 1-16

wrong

correct

rail

strap

5/16" Flange nut

5/16" x 3/4" Hex head bolt

[

]

[

]

carriage stop

USES BUMPER

NO BUMPER

MAIN ASSEMBLY

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

14. Attach emergency release knob, cord

and tag.

•Tie an overhand knot in one end of

emergency release cord [17].

–

Slidecordthroughcenterof knob

[18]

Fig. 1-17.

– Slide cord through hole in emergency

release lever (on carriage).

– Tie a second knot in this end. Fig. 1-18.

– Slip wire of emergency release tag [19]

through hole in emergency release lever

and twist it around itself.

15. Attach limit switches.

•“CLOSE” limit switch

[15B]

(Switches are identical.)

– Place “CLOSE” limit switch over top of rail

about 12 inches from r

ail strap. Fig. 1-19.

– Check that white lever is toward

power head.

–Insert set screw [16] into limit switch

hand

tight only to temporarily hold switch

in place. Fig. 1-19A.

– Attach bro

wn wire to switch. Fig. 1-19B.

– Leaving some slack in wire (Fig. 1-20),

run wire down inside groove in top of rail

back to power head.

– Use wire clip [44] to help maintain slack.

Fig. 1-20.

•“OPEN” limit switch

[15A]

– Place “OPEN” limit switch over top of rail

about 12 inches from po

wer head. Fig.1-21.

– Check that white lever is on side away from

power head. (This means limit switches

hang off opposite sides of rail. Check this

to help verify they are installed properly.)

–Insert set screw [16] into limit switch hand

tight only to temporarily hold switch in place.

– Attach gre

y wire to switch. Fig. 1-21.

– Leaving some slack in wire (Fig. 1-21),

run wire down inside groove in top of rail

back to power head.

– Use wire clip [44] to help maintain slack.

Fig. 1-21.

• Coil excess wire and tape it to top of power

head. Fig. 1-21A.

Fig. 1-19

Fig. 1-20

wire clip

pow

er head

Fig. 1-21

“close”

switch

“open”

switch

set screw

OPEN GREEN PARTS BAG

Screws for attaching light cover are included in this bag.

Please set aside for use later.

grey wire

brown wire

Fig. 1-17

Fig. 1-18

release

knob

tag

cord

#8-32 x 3/8" Hex head screw

Wire clip

[

]

[

]

SECT 2—INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

NOTE:There are differences in installations

depending on which type of door you have.

These differences are explained throughout

this section. Please note those steps which are

applicable to your particular door.

REFER TO PAGES 2 & 3.

There are two basic types of residential garage

doors.They are:

SECTIONAL DOORS—divided into a set of

narrow panels (usually four) connected by

hinges, so door can “bend” as it rides on a

curved track.

1-PIECE DOORS—consist of one large

panel and swivel on large spring-loaded hinges

on each side of door.

1. Determining header bracket location.

• Find center of door from side to side.

– Measure overall width of door.

(example: 16 feet)

– Divide overall width by 2.

(example: 16

2 = 8 feet)

• Measure this distance from side of door and

draw a pencil line vertically from the top of

the door down approximately 1 foot.This is

the centerline. Fig. 2-1.

– Continue marking centerline on wall

above door from top of door up

approximately 1 foot. Fig. 2-1.

floor

garage door

TYPICAL TRACK GUIDED

CENTERLINE

floor

garage door

TYPICAL TRACKLESS

CENTERLINE

Fig. 2-1

Sectional doors may have one

torsion spring (as shown) or two

springs (one on each side).

Some older doors may have

extension springs.

INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

2. Finding highest point of travel.

• While raising garage door manually, watch

top edge of door to see where it reaches its

highest point.This is called “highest point of

travel.” Fig. 2-2.

•A locking pliers can be used to hold the

door in position by clamping it onto the rail.

(A stool, chair, table or any object that can

safely support door will also work.)

–With door held partly open (at its “highest

point”), measure distance from top edge

to the floor.

• Remove support and gently lower door.

• Mark “highest point of travel” at centerline

on wall above door. Fig. 2-3.

NOTE: Following step depends on type of door.

3. Final header bracket mounting location.

•For SECTIONAL DOORS—

add 2-1/2 inches to “highest point of travel”

and mark this height on centerline. Fig. 2-3.

•For ONE-PIECE DOORS—

add 6 inches to “highest point of travel” and

mark this height on centerline. Fig. 2-4.

Highest point of travel.

Measure from here to

floor

SECTIONAL DOORS

ONE-PIECE DOORS

Fig. 2-2

Highest point of travel.

Measure from here to

floor

Fig. 2-3

Highest point of travel.

+6"

Highest point of travel.

+2-1/2"

Fig. 2-4

centerline of door

INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

NOTE: If torsion spring interferes with your

final location, mark bracket location 2-1/2" or

6" above torsion spring depending on garage

door type.

4. Check mounting location for strength.

Header bracket must be attached to

framework of garage. Fig. 2-5.

• If final header bracket position is on

garage

door header, continue with step 5.

• If final header bracket position is abo

garage door header, a mounting plate must

be installed and mounting location must be

remarked before continuing with step 5.

Fig. 2-5.

• If your garage wall is finished (covered with

drywall), continue with step 5.

5. Mounting preparation.

• Hold bracket against wall where final header

bracket height crosses centerline.

• Make sure flange where rail strap attaches,

is on centerline. Fig. 2-6.

• Mark screw hole locations.

– If your wall is finished, take a small “finish

nail” and gently tap it through drywall

where you have marked screw holes to

find out if there is wood behind mounting

location. If your marked location is solid

continue with step 6.

– If your marked mounting location is not

solid, a mounting plate must be installed

and mounting location remarked before

continuing. Fig. 2-7 and Fig. 2-5.

6. Mount header bracket [20].

•Drill 5/32 inch pilot holes at marked screw

hole locations.

•Fasten header bracket using 3 lag

screws [22].

floor

ceiling

garage door opening

header

studs

wall

TYPICAL UNFINISHED WALL

floor

ceiling

garage door opening

TYPICAL FINISHED WALL

wooden plate

fastened to wall studs

wooden plate

fastened to wall studs

Fig. 2-5

Fig. 2-7

flange for

rail strap

Fig. 2-6

flange for

rail strap

centerline of door

1/4" x 2" Lag screw

[

]

OPEN ORANGE PARTS BAG

header

bracket

header

bracket

INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

7. Attaching rail to header bracket.

• Gently set power head on garage floor while

leaning rail strap against header bracket. (It

is recommended that you place a piece of

cardboard or similar material between power

head and floor to prevent scrapes and

scratches to power head.)

NOTE: It may be necessary to support power

head above floor. As little as a few inches, or

as much as 5 or 6 feet depending on position

of torsion spring(s). Be sure to use a stable

support device, such as a ladder.

• Slide threaded stud of rail strap through hole

in flange of header bracket.

•Fasten with nut[9], finger tight only. Fig. 2-8.

Fig. 2-8

5/16" Flange nut

[

]

5/16"

FLANGE

NUT

INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

8. Mounting power head.

• Raise power head and support it high

enough that you can manually raise garage

door fully open.

• Line up power head and rail with center of

door. Fig. 2-9.

•Keeping power head centered, mount

to ceiling:

–at proper height;

a. for sectional doors rail should be level

with floor or slightly below level.

Fig. 2-10.

b. for 1-piece doors rail should clear

door by about 2 inches. Fig. 2-10.

– using one of the preferred methods

shown, Fig. 2-11, mount power head.

(It is possible to use other mounting

methods.The critical point to remember is

that the mounting assembly must be

solidly attached and able to support the

weight of the power head.) DO NOT

ATTACH TO DRY WALL OR

SUSPENDED CEILING. It must be

anchored to the framework of the garage.

• Fully tighten rail strap nut.

Fig. 2-9

SECTIONAL LEVEL OR SLIGHTLY BELOW LEVEL

1-PIECE MUST CLEAR DOOR BY 2 INCHES AT HIGHEST POINT OF TRAVEL

Fig. 2-10

Perforated

Angle Iron

Mounting

Straps

FINISHED CEILING

Wood

Fig. 2-11

[22]

[48]

[46]

[9]

INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

9. Mounting door bracket [21].

• Center of bracket must be on centerline of

door and must be mounted as high as

possible. Fig. 2-12A & B.

• Hold bracket against door at preferred

location and mark screw holes.

– for wooden doors, drill 5/32 inch

pilot holes.

a. Fasten door bracket using

3 lag screws [22].

b. Check thickness of door against lag

screws. (It may be necessary to

mount door bracket on a 2" x 6",

etc. attached to inside of door to

prevent screws from coming out

other side of garage door.

Fig. 2-12A.

– for light-weight doors

CAUTION: In the case of sectional doors, the

door bracket must not be below the highest set

of rollers. Fig. 2-13.

– there are a wide variety of reinforcements

depending on manufacturer and some are

equipped with hardware that is intended

to be used in place of the door bracket.

Be sure to confirm proper use of

this hardware with your door

manufacturer. Unauthorized improper

use of these attachment systems

could void your warranty.

WHEREVER POSSIBLE—USE DOOR

BRACKET SUPPLIED WITH YOUR

GENIE OPERATOR.

a. Fasten door bracket using

3 self-drilling screws [47].

Fig. 2-12B

Fig. 2-12A

top of door

centerline

top of door

attached board for

extra thickness

even with or

above top roller

Fig. 2-13

WOODEN ONE-PIECE

LIGHT-WEIGHT SECTIONAL

1/4" x 2" Lag screw

[

]

1/4"-20 Self-drilling screw

[

]

door bracket

La page charge ...

Genie ISL950 Manuel utilisateur

Marque: Genie

Modèle: ISL950

Catégorie: Porte de garage

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Genie ISL950 User manual

Genie ISL950 Manuel utilisateur

Genie ISL950 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents