Phase Technology P3-35 Amplifier Le manuel du propriétaire

Marque: Phase Technology

Modèle: P3-35 Amplifier

Catégorie: Équipement musical supplémentaire

Taper: Le manuel du propriétaire

Warning

Phase Technology products must be installed by a professional audio installer/contractor. For safety and for

optimum audio performance, installer must follow all directions issued by Phase Technology.

Box Contents

1- Amplier

1- Bluetooth

antenna

1- IR receiver with 1m cord

1- 32 V, 3.75 A power supply

1- Six-pin Euroblock connectors

1- Three-pin Euroblock connectors

1- Mounting bracket

2- 2" Velcro strips

1- Double sided tape disk for IR receiver

The P3-35 is a 2 or 3 channel amplier with Dolby Digital

decoding. It is designed to be used with either an analog or digital input from a TV or other audio

source. With a digital input it automatically senses Dolby Digital and PCM and switches modes. The P3-35 takes the input signal from an audio source, decodes

it and outputs either a 2 or 3 channel amplied signal to a sound bar or set of speakers. When set in the 2 channel mode it will take a stereo or multi-channel

signal and mix it down to 2 output channels (left and right). When set in the 3 channel mode it will take a stereo or multi-channel signal and mix it into 3 output

channels (left, right and center). In either mode there is a sub out option.

When used in place of internal TV speakers, change the TV’s audio setting to external speakers. Teach the P3-35 the TV’s volume codes and it seamlessly

operates with no additional remotes.

Install Instructions For:

P3-35

IMPORTANT SAFETY INFORMATION

1. Read these instructions.

2. Keep these instructions.

3. Heed all warning.

4. Follow all instructions

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for

your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracked, or table specied by the manufacturer, or sold with the apparatus. When a cart

is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way,

such as power-supply cold or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING:

To reduced the risk of re or electric shock, do not expose this apparatus to rain or moisture

The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed

on the apparatus.

Manufactured under license from Dolby Labroatories. Dolby and the double-D symbol are

registeres trademarks of Dolby Laboratories.

Install Instructions For:

P3-35

1. Unpack amplier.

Note: Follow steps 2-5 if

using the mounting adapter.

If not skip to step 6.

2. Attach mounting bracket

to a secure pole or surface

using screws or metal

strapping.

1. to connect wires to the

Euro-Block connector

loosen the screws, insert a

1/4" in of stripped wire and

tighten the screws.

Note: make sure there are

no loose strands of wire.

6. If mounting to a at

surface use 2 screws

through the mounting

bracket on each end of the

amp.

4. Slide mounting bracket

into groove on bottom of

amplifer enclosure.

3. For 3 channels connect

the speakers to the two

outer sets of terminal for

your left and right channels

and the center set for the

center channel. Set dip

switch 5 in the down

position.

2. For 2 channels (Stereo)

connect your speakers to the

2 outer sets L and R

terminals. Set dip switch 5 in

the up position.

1a. Make sure the + wire is

connected to the plus or

red terminal on your

speaker and the – to the

negative or black terminal

on the speaker.

1. Connect a Subwoofer to

the P3-35 with an Audio

RCA cable.

5. Replace faceplate screws

Mounting the P3-35

Speaker Connections

STEREO

Connecting a Subwoofer

3. To attach mounting

bracket, remove all faceplate

screws from one side. Lift

faceplate and set aside.

3 CHANNEL

123456

Install Instructions For:

P3-35

7. The power supply can

be attached to a mounting

surface using the Velcro

strips. Make sure the velcro

is placed on outer most

plastic portion of the power

supply (do not stick it to the

label).

Installed

1. For digital connections

connect an optical cable

from your source to the

optical input on the P3-35.

Set dip switch 6 in the

down position.

3. To use an external Sub

crossover set dip switch 1 to

the down (line) position.

2. To use the internal P3-35

crossover set to 120Hz set

dip switch 1 to the up (Sub)

position.

2. For analog connections

connect a cable from your

analog source to the

analog input using a stereo

1/8”mini-jack. Set dip

switch 6 in the up position.

2. Position the IR receiver on

a surface that faces out into

the area you will be using the

remote control. Fasten the

IR receiver with the supplied

two-sided tape disk.

1. Connect the 1/8” mini plug

from the IR receiver to the

External IR port on the

P3-35.

1. Connect the 32v power

supply barrel connector to

the power input on the

P3-35.

3. Turn the P3-35 on by

pressing the on/off button.

The LED will turn white when

on.

Note: In order to program the

P3-35 remote, the unit must

be disconnected from an

input source. It must be in the

stand-by mode (white LED).

Connecting Your Wired Audio Source

Connecting Power to the P3-35 Controlling volume using a TV remote

Flat Panel Display

6. Repeat step 5 with the

volume down button. The

purple LED will blink 3 times

rapidly.

5. Point the TV remote at the

IR receiver and press the

volume up button 3 times.

The purple LED will blink 3

times rapidly.

4. Press and hold the on/off

button on the P3-35 until it

starts blinking purple

(approximately 5 sec).

7. Repeat step 5 with the

mute button. The purple

LED will blink 3 times

rapidly then turn solid

white. The amp is now

programmed and will

respond to the remote

control volume

commands.

123456 123456 456

Flat Panel Display

IR Receiver

Flat Panel Display

IR Receiver

Flat Panel Display

IR Receiver

Install Instructions For:

P3-35

RS232 Control

Pairing with a Bluetooth device

2. All serial commands

should be sent as listed

above.

1. Connect the RS232

control device to the RS232

port on the P3-35. Refer to

Step 1 of “Speaker

Connections” for instructions

on wiring the Euro-Block

connector.

1. Turn the P3-35 on by

pressing the on/off button.

The LED will turn white

when on.

1. There are two EQ settings

you can choose at or +3dB.

3. Select PhaseTech on your

Bluetooth device to pair

them.

2. Press and hold the mute

button on the remote

control for 3 seconds then

release. The P3-35 LED

will blink white for 1 minute

or until paired.

2. To boost the low

frequencies set Dip switch

2 to the up position (+3dB)

Equalizer settings

Baud Rate 115200

Data Bits 8

Parity none

Stop bit 1

Flow Control none

PhaseTech

4. To boost the high

frequencies set Dip switch 4

to the up position (+3dB)

3. To boost the mid

frequencies and increase

intelligibility set Dip switch 3

to the up position (+3dB)

4. Bluetooth (BT) will take

priority over a wired audio

signal when playing BT

Audio. When you stop or

pause BT audio the wired

audio will play.

PhaseTech

Install Instructions For:

P3-35

3. Ascii commands above are followed by a Carriage

Return.

Note: The mute command is followed by a space then the

numerical value.

The SV command is followed by a space then the numerical

value of 0-81 to set the relative level.

All other alphanumeric variables have no space.

Reset sets the amp in sleep mode, volume at 40 and clears

the remote codes.

Ascii Description

UV1 Volume up one step

UV5 Volume up ve steps

DV1 Volume down one step

DV5 Volume down ve steps

MUTE 1 Mute

MUTE 0 Unmute

Ascii Description

GV Get Volume setting

SV 0-81 Send Volume setting

AON Amp on

AOFF Amp off

Reset Resets to factory default

Standby and sleep settings

There are two modes the P3-35 can operate in; Standby and Sleep. Setting the P3-35 in the standby mode disables the auto-on

input signal sensing. In this mode the P3-35 can only be turned on by pressing the Volume control On/Off switch or through RS232

control.

Setting the P3-35 in the sleep mode enables auto-on input signal sensing and will turn the P3-35 on when there is a signal present

and will automatically turn off when there is no signal for 5-7 minutes.

Note: The P3-35 goes into standby mode 5 minutes after it stops sensing a signal provided the amp is set to standby mode.

The P3-35 will be switched into networked sleep mode in 5 minutes after it stops sensing a Bluetooth or wired audio signal provided

the amp is set in sleep mode.

Setting the operating mode:

1. With the on/off switch in the off position (Red LED).

2. Press and hold the on/off switch for 10 seconds or until the LED starts blinking for 3 seconds.

3. If it blinks Blue it is in Sleep mode

If it blinks Green it is in Standby mode.

4. To change the mode repeat step 2.

LED mode guide

Standby: RED

Power on/No signal: White

Analog/PCM: Green

Dolby: Purple

Bluetooth: Blue

Bluetooth pairing: White blinking

IR learning mode: Purple blinking

Sleep: Blue blinking

Standby: Green Blinking

Note:

P3-35’s that are shipped to the EU market meet the following requirements.

The power consumption of the product in networked standby is less than 3W.

The power consumption of the product in standby mode is less than 0.5W.

Install Instructions For:

P3-35

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation

est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate

the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-

ment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful commu-

nication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et

d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Install Instructions For:

P3-35

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna

of this device and persons during device operation.

To ensure compliance, operations at closer than this distance is not recommended.

Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de

20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’

antenne.

La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son

functionnement.

This radio transmitter (identify the device by certication number, or model number if Category II) has been approved by Industry

Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for

each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Gain of antenna: 2.0dBi max.

Type of antenna: Omni-directional

Impedance of antenna: 50ohm

Le présent émetteur radio (identier le dispositif par son numéro de certication ou son numéro de modèle s'il fait partie du matériel

de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un

gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou

dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Gain d'antenne: 2.0dBi maximal

Type d'antenne: 50 ohm, Omni-directionnel

Install Instructions For:

P3-35

Phase Technology P3-35 Amplifier Le manuel du propriétaire

Marque: Phase Technology

Modèle: P3-35 Amplifier

Catégorie: Équipement musical supplémentaire

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Phase Technology P3-35 Amplifier Owner's manual

Phase Technology P3-35 Amplifier Le manuel du propriétaire

Phase Technology P3-35 Amplifier Le manuel du propriétaire

dans d''autres langues

Autres documents