GE AEY05LN Le manuel du propriétaire

Safety Instructions ............. 2, 3

Operating Instructions

Controls ........................... 4–6

Care and Cleaning

Air Filter ..............................6

Outdoor Coils .........................6

Installation Instructions ......7–10

Troubleshooting Tips ............11

Normal Operating Sounds ............11

Consumer Support

Consumer Support .......... Back Cover

Ownership Registration for

Customers in Canada only ........ 13, 14

Warranty for Customers

in Canada ...........................16

Warranty for Customers

in the U.S.A. ..........................15

49-7640 01-10 GE

AET05

AEY05

Owner’s Manual and

Installation Instructions

Write the model and serial numbers here:

Model # __________________________

Serial # __________________________

Find these numbers on a label on the

side of the air conditioner.

Air Conditioners

GEAppliances.com

Room

Climatiseur

Acondicionador

de aire

Manuel d’utilisation et

instructions d’installation

Manual del propietario

y instrucciones de

instalación

La section française commence à la page 17

La sección en español empieza en la página 33

In Canada, contact us at:

www.GEAppliances.ca

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

n Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

n This air conditioner must be properly

installed in accordance with the Installation

Instructions before it is used.

n Never unplug your air conditioner by pulling

on the power cord. Always grip plug firmly

and pull straight out from the receptacle.

n Replace immediately all electric service

cords that have become frayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained from the manufacturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its length

or at either the plug or connector end.

n Turn the unit OFF and unplug your air

conditioner before cleaning.

n GE does not support any servicing of the

air conditioner. We strongly recommend

that you do not attempt to service the air

conditioner yourself.

n For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

n All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants, check

with the company handling disposal about

what to do.

n If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

n These R410A air conditioning systems

require contractors and technicians to

use tools, equipment and safety standards

approved for use with this refrigerant.

DO NOT use equipment certified for

R22 refrigerant only.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

For personal safety, this appliance must be properly

grounded.

DO NOT use an adapter plug with this appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric

shock hazard from this appliance.

Power cord includes a current interrupter device.

A test and reset button is provided on the plug

case. The device should be tested on a periodic

basis by first pressing the TEST button and then

the RESET button while plugged into the outlet. If

the TEST button does not trip

or if the RESET button will not stay engaged,

discontinue use of the air conditioner and

contact a qualified service technician.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be plugged

into its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

3

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

GEAppliances.com

WARNING!

Because of potential safety hazards under certain

conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14-gauge, 3-wire grounding-type appliance

extension cord having a grounding-type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

USE OF EXTENSION CORDS—115-Volt models only

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY

.

SAVE THESE INSTRUCTIONS

4

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

About the controls on the air conditioner

Features and appearance will vary.

Controls (on some models)

Mode Control

High Cool and Low Cool provide cooling with

different fan speeds.

Fan settings provide air circulation and filtering

without cooling.

NOTE: If you move the mode control from a cool

setting to OFF or to a fan setting, wait at least

3 minutes before switching back to a cool

setting.

Cooling Descriptions

For Normal Cooling—Select High Cool or Low

Cool with the TEMPERATURE control at midpoint.

For Maximum Cooling—Select High Cool with

the TEMPERATURE control at the highest number

available on your knob.

For Quieter and Nighttime Cooling—Select Low

Cool with the TEMPERATURE control at midpoint.

TEMP Control

The TEMP control is used to maintain the room

temperature. The compressor will cycle on

and off to keep the room at the same level of

comfort. When you turn the knob to a higher

number, the indoor air will become cooler. Turn

the knob to a lower number and the indoor air

will become warmer.

MODE CONTROL

TEMPERATURE CONTROL

GEAppliances.com

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

5

Controls (on some models)

Air Direction

Use the lever to adjust the air direction left and right

only.

Air Filter

The air filter behind the front grille should be checked

and cleaned at least every 30 days or

more often if necessary.

To remove:

Pull the tab on the right side of the unit until the filter

is out.

Clean the filter with warm, soapy water. Rinse and let

the filter dry before replacing it. Do not clean the filter

in a dishwasher.

CAUTION: DO NOT operate the air conditioner

without a filter because dirt and lint will clog it and reduce

performance.

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged with

dirt or soot, they may be professionally cleaned.

6

Turn the air conditioner off and remove the plug from

the wall outlet before cleaning.

To clean, use water and a mild detergent. Do not use

bleach or abrasives.

Grille and Case

Care and cleaning of the air conditioner.

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time –

Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• You MUST use all supplied parts and use proper

installation procedures as described in these

instructions when installing this air conditioner.

Installation

Air Conditioner

Instructions

Some models require a 115/120-volt AC,

60-Hz grounded outlet protected with a

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall outlet you

plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt AC,

protected with a time-delay fuse or circuit

breaker. These models should be installed on

their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

ELECTRICAL REQUIREMENTS

CAUTION:

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Do not change the plug on the power cord of this air

conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

7

TOOLS YOU WILL NEED

Phillips head screwdriver

Ruler or tape measurePencil

Level

Scissors or knife

Flat-blade screwdriver

Power cord includes a current interrupter

device. A test and reset button is provided on the

plug case. The device should be tested on a periodic

basis by first pressing the TEST button and then the

RESET button while plugged into the outlet. If the

TEST button does not trip or if the RESET button will not

stay engaged, discontinue use of the air conditioner

and contact a qualified service technician.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

8

Installation Instructions

Right

accordion

panel

Type A (4) Type B (6)

Foam top window

gasket

Left

accordion

panel

Window

sash seal

Top mounting rail

Air

conditioner

Window locking

bracket (1)

PARTS INCLUDED

(Appearance may vary)

Top mounting rail

seal strip

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt toward the outside, and will keep it

from draining properly.

To adjust for this, attach a piece of wood to the sill.

WOOD PIECES

WIDTH: 2”

LENGTH: Long enough to fit inside the window

frame.

THICKNESS: To determine the thickness, place a

piece of wood on the sill to make it 1/2” higher than

the top of the storm window frame or the vinyl

frame.

Attach securely with nails or screws provided by the

installer.

Installation Instructions

WINDOW REQUIREMENTS

•These instructions are for a standard double-hung

window. You will need to modify them for other types

of windows.

•The air conditioner can be installed without the

accordion panels if needed to fit in a narrow

window. See the window opening dimensions.

•All supporting parts must be secured

to firm wood, masonry or metal.

•The electrical outlet must be within reach of the

power cord.

•Follow the dimensions in the table and illustration

for your model.

1

(With accordion panels)

PREPARE THE AIR CONDITIONER

Install the top mounting rail with 4 Type A

screws from the outside of the case.

Hold the accordion panel in one hand and

gently pull back to free the open end.

4

A

B

Top mounting rail

Bottom mounting rail

2

1/2” higher

than storm

window

frame

Storm window

frame

Wood

Sill

1/2” higher

than vinyl frame

(on some windows)

Vinyl frame

3

Top mounting rail

Remove

backing

from seal

strip

Top mounting rail

Seal strip

FRONT VIEW

9

12.5”

23”- 38”

ATTACH THE TOP MOUNTING

RAIL SEAL STRIP

(Some models may have the seal strip

already attached to the top mounting rail.

If applicable, skip this step.)

Remove the backing from the top mounting

rail seal strip and attach the seal strip to the

bottom of the top mounting rail, along the

front edge.

Installation Instructions

PREPARE THE AIR CONDITIONER (cont.)

Slide the free end of the accordion panel

into the side panel rails. Slide the panel

down. Be sure to leave enough space to

slip the top and bottom of the frame into

the rails on the cabinet.

NOTE: There is a right and a left accordion

panel. Be sure to use the proper panel for

each side.

Slide the left and right accordion panels

into the top and bottom mounting rails.

4

6

A

B

Type B screws

or

PREPARE THE WINDOW

Cut the window sash seal to the proper length.

Peel off the backing and attach the seal to the

underside of the window sash.

5

C

7

INSTALL SUPPORT BRACKET AND

FOAM TOP WINDOW GASKET

Cut the foam top window gasket to the window

width.

Stuff the foam

between the glass

and the window

to prevent air and

insects from getting

into the room.

NOTE: If the gasket supplied does not fit your

window, obtain appropriate material locally to

provide a proper installation seal.

A

CAUTION:

To prevent broken glass or

damage to windows, on

vinyl or other similarly

constructed windows,

attach the window locking

bracket to the window

side jamb with one Type B

screw.

B

C

Wood

Vinyl

10

Top left

Top right

D

Top mounting rail

Bottom mounting rail

INSTALL THE AIR CONDITIONER

IN THE WINDOW

Place the air conditioner on the sill with

the bottom mounting rail against its back

edge. Center it and close the window

securely behind the top mounting rail.

It should be level or slightly tilted to the

outside. Use a level; about a 1/3 bubble

will be the correct case slant to the outside.

Extend the left and right accordion panels

to the vertical window sashes and attach,

through the holes in the panels, with 5 Type

B screws, as appropriate.

Troubleshooting Tips. GEAppliances.com

Normal Operating Sounds

n You may hear a pinging noise caused by

water being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

n You may hear the thermostat click when the

compressor cycles on and off.

n Water will collect in the base pan during

high humidity or on rainy days. The water

may overflow and drip from the outdoor side

of the unit.

n The fan may run even when the compressor

does not.

Problem Possible Causes What To Do

Air conditioner The air conditioner •Make sure the air conditioner plug is pushed

does not start is unplugged. completely into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace

breaker is tripped. the fuse or reset the breaker.

Power failure. •The unit will automatically restart in the settings last

used after the power is restored.

•There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling for 3 minutes after it is turned

back on.

The current interrupter •Press the RESET button located on the power cord plug.

device is tripped.

•If the RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified

service technician.

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or furniture

not cool as it should blocking the front of the air conditioner.

The temp control may • Turn the temperature knob to a higher number.

not be set correctly.

The air filter is dirty. • Clean the filter at least every 30 days.

See the Care and Cleaning section.

The room may have been hot. • When the air conditioner is first turned on, you need

to allow time for the room to cool down.

Cold air is escaping. • Check for open furnace registers and cold air returns.

Cooling coils have iced up. • See “Air conditioner freezing up” below.

Air conditioner Ice blocks the air flow • On models with control knobs, set the mode control at

freezing up and stops the air conditioner High Fan or High Cool with the Temp at 1 or 2.

from cooling the room.

Water drips outside Hot, humid weather. • This is normal.

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside. slants slightly from the case front to the rear.

Water collects in Moisture removed from air • This is normal for a short period in areas with little

base pan and drains into base pan. humidity; normal for a longer period in very humid areas.

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

11

12

Safety InstructionsOperating Instructions

Care and Cleaning

Installation InstructionsTroubleshooting TipsConsumer Support

Notes.

13

OWNERSHIP REGISTRATION

P.O. BOX 1780

MISSISSAUGA, ONTARIO

L4Y 4G1

(FOR CANADIAN CONSUMERS ONLY)

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez à :

14

Consumer SupportTroubleshooting TipsInstallation Instructions

Care and Cleaning

Operating Instructions Safety Instructions

n Customer instruction. This owner’s manual provides

information regarding operating instructions and

user controls.

n Improper installation. If you have an installation problem,

or if the air conditioner is of improper cooling capacity

for the intended use, contact your dealer or installer.

You are responsible for providing adequate electrical

connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n Replacement of house fuses or resetting of circuit

breakers.

n Failure due to corrosion on models not corrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties, whether

express, oral or statutory which extend beyond the description on the face hereof, including specifically the

implied warranties of merchantability or fitness for a particular purpose.

Warrantor: General Electric Company. Louisville, KY 40225

n Properly pack your unit. We recommend using

the original carton and packing materials.

n Return the product to the retail location where

it was purchased.

n Include in the package a copy of the sales receipt or

other evidence of date of original purchase. Also print

your name and address and a description of the defect.

In Order to Make a Warranty Claim During the First 30 Days from the Date of Original Purchase:

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product replacement as provided

in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness

for a particular purpose, are limited to one year or the shortest period allowed by law.

GE Air Conditioner—One Year Limited Warranty. (For customers in the U.S.A.)

For The Period Of: We Will Replace:

One Year Replacement unit for any product which fails due to a defect in materials or workmanship.

From the date of the The replacement unit is warranted for the remainder of your product’s original one-year

original purchase warranty period. The replacement unit may either be a new unit or a refurbished unit.

Staple your receipt here.

Proof of the original purchase date

is needed to make a warranty claim.

n Locate your original sales receipt and make a note

of your model and serial number.

n Call GE at 1.866.907.1655 to initiate the product

replacement process.

n You will be asked to provide your name, address,

date of purchase, model and serial number.

n GE will arrange for a carton to be sent to your home

to recover the product.

n You must return the product (postage pre-paid by GE)

to GE’s recovery center before a replacement unit will be

provided. Please include a description of the defect.

n You should receive your replacement product within

7 to 10 business days after your unit is received.

n If you experience any problems or delays after initiating

the replacement process, please call 1.256.796.6610 for

assistance.

In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:

15

16

Safety InstructionsOperating Instructions Care and CleaningInstallation InstructionsTroubleshooting TipsConsumer Support

For The Period Of: We Will Replace:

One Year Replacement unit for any product which fails due to a defect in materials or workmanship.

From the date of the The replacement unit is warranted for the remainder of your product’s original one-year

original purchase warranty period.

GE Air Conditioner—One-Year Limited Warranty. (For customers in Canada)

n Customer instruction. This owner’s manual provides

information regarding operating instructions and

user controls.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner is

of improper cooling capacity, contact your dealer or

installer. You are responsible for providing adequate

electrical, plumbing and other connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use, including failure

to provide reasonable and necessary maintenance.

n Replacement of house fuses or resetting of circuit

breakers.

n Failure due to corrosion on models not corrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from

province to province. To know what your legal rights are in your province, consult your local or provincial consumer affairs

office.

Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties, whether

express, oral or statutory which extend beyond the description on the face hereof, including specifically the

implied warranties of merchantability or fitness for a particular purpose.

Warrantor: Mabe Canada Inc.,

Burlington, Ontario

Staple your receipt here.

Proof of the original purchase date is needed to

make a warranty claim.

n Properly pack your unit. We recommend using the

original carton and packing materials.

n Return the product to the retail location where it

was purchased.

n Include in the package a copy of the sales receipt or

other evidence of date of original purchase. Also print

your name and address and a description of the defect.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product replacement as provided

in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness

for a particular purpose, are limited to one year or the shortest period allowed by law.

In Order to Make a Warranty Claim:

Consignes de sécurité .............18, 19

Consignes d’utilisation

Commandes ..........................20–22

Entretien et nettoyage

Filtre à air ................................22

Serpentins extérieurs .....................22

Instructions de montage ...........23–26

Conseils de dépannage ...............27

Bruits normaux de fonctionnement ........27

Assistance à la clientèle

Assistance à la clientèle ...................32

Garantie ..................................31

Enregistrement du titre

de propriété ...........................29, 30

Inscrivez ici les numéros de modèle et de série :

Numéro de modèle : ____________________

Numéro de Série : _____________________

Vous trouverez ces numéros sur l’étiquette

apposée sur le côté du climatiseur.

17

Au Canada, visitez-nous au :

www.electromenagersge.ca

AET05

AEY05

Assistance à

la clientèle

Conseils de

dépannage

Instructions

de montage

Entretien et

nettoyage

Consignes

d’utilisation

Consignes

de sécurité

18

IMPORTANTES CONSIGNES DE SÉCURITÉ.

VEUILLEZ LIRE TOUTES LES CONSIGNES AVANT UTILISATION.

AVERTISSEMENT !

Pour votre sécurité, les informations contenues dans ce manuel doivent être suivies afin de minimiser

les risques d’incendie, de chocs électriques ou de blessures corporelles.

n N’utilisez cet appareil qu’aux fins prévues

décrites dans le manuel d’utilisation.

n Ce climatiseur doit être correctement

installé conformément aux Instructions

d’Installation avant toute utilisation.

n Ne débranchez jamais votre climatiseur en

tirant sur le cordon d’alimentation. Prenez

toujours fermement la fiche en main et tirez

pour la sortir de la prise.

n Remplacez immédiatement tout cordon

électrique usé ou endommagé. Un

cordon d’alimentation endommagé doit

être remplacé par un nouveau cordon

d’alimentation obtenu du fabricant. Ne

réparez pas le cordon endommagé. N’utilisez

pas un cordon fissuré ou présentant des

dommages dus aux frottements soit sur

sa longueur ou aux extrémités du côté

de la fiche ou du raccord.

n Eteignez votre climatiseur et débranchez-le

avant de le nettoyer.

n GE n’offre pas de service d’entretien pour les

climatiseurs. Nous vous recommandons de

ne pas essayer d’effectuer l’entretien

de votre climatiseur vous-même.

n Pour votre sécurité, ne stockez pas et

n’utilisez pas de matériaux combustibles,

d’essence ou d’autres vapeurs et liquides

inflammables dans les parages de cet

appareil ou de tout autre appareil.

n Tous les climatiseurs contiennent des

fluides frigorigènes qui, conformément, à la

législation fédérale doivent être retirés avant

la mise au rebut de l’appareil. Si vous mettez

au rebus un ancien appareil contenant des

fluides frigorigènes, vérifiez la procédure à

suivre auprès de la compagnie responsable

de l’élimination.

n Si la prise de courant est d’un format

différent de la fiche, cette prise doit être

changée par un électricien qualifié.

n Ces systèmes de climatisation R410A

nécessitent que les entrepreneurs et

techniciens adoptent des outils, du matériel

et des normes de sécurité approuvés pour

utilisation avec ce réfrigérant. N’utilisez pas

de matériel certifié pour le réfrigérant R22

uniquement.

CONSIGNES DE SÉCURITÉ

Ne coupez pas ou n’enlevez pas, sous aucun

prétexte, la troisième broche de mise à la terre

du cordon d’alimentation. Pour des raisons

de sécurité, cet appareil doit être correctement

mis à la terre.

N’utilisez PAS d’adaptateur avec cet appareil.

Le cordon d’alimentation de cet appareil

est équipé d’une fiche à trois broches (pour une

mise à la terre) qui s’adapte à la prise

de courant standard à 3 broches (pour une mise

à la terre) pour minimiser les risques

de chocs électriques par cet appareil.

Le cordon d’alimentation est équipé d’un

dispositif d’interruption du courant. Un bouton

d’essai et de réenclenchement est fourni

sur le boîtier de la prise. Vous devez tester le

mécanisme régulièrement en appuyant d’abord

sur le bouton TEST (essai) puis sur le bouton

RESET (réenclenchement) lorsque l’appareil est

branché. Si le bouton TEST (essai) ne bascule pas

ou si le bouton RESET (réenclenchement) ne reste

pas enclenché, cessez d’utiliser votre climatiseur

et appelez un technicien de service qualifié.

Faites vérifier la prise murale et le circuit

électrique par un électricien qualifié pour

s’assurer que le système est correctement

mis à la terre.

Dans le cas d’une prise biphasée,

l’installateur a la responsabilité et l’obligation

de la remplacer par une prise triphasée

correctement mise à la terre.

Le climatiseur doit toujours être branché

à sa propre prise électrique d’une tension

nominale correspondant à celle indiquée

sur sa plaque signalétique.

Ceci permet d’obtenir un meilleur rendement

du climatiseur et évite de surcharger les circuits

électriques du domicile qui risque d’occasionner

un incendie en surchauffant.

Consultez les Consignes d’Installations, dans

la section Exigences Electriques pour les

exigences de branchements électriques

particuliers.

BRANCHEMENTS ÉLECTRIQUES

Consignes

de sécurité

Consignes

d’utilisation

Entretien et

nettoyage

Instructions

de montage

Conseils de

dépannage

Assistance à

la clientèle

19

www.electromenagersge.ca

AVERTISSEMENT !

Nous déconseillons fortement l’utilisation d’une

rallonge à cause des risques potentiels dans

certaines conditions.

Cependant, si l’utilisation d’une rallonge est

nécessaire, cette dernière doit obligatoirement

être homologuée UL, de calibre 14, à trois

brins avec mise à la terre pour appareil

électroménager et doit être équipée d’une fiche

et d’une prise femelle avec terre.

Les caractéristiques électriques de la rallonge

doivent être de 15 ampères (minimum)

et de 125 volts.

MISE EN GARDE :

N’UTILISEZ PAS de rallonge avec un modèle

à 230/208 Volts.

UTILISATION DE RALLONGES—modèles à 115 Volts uniquement

LISEZ ET SUIVEZ SOIGNEUSEMENT CES CONSIGNES DE

SÉCURITÉ.

CONSERVEZ CES INSTRUCTIONS

Assistance à

la clientèle

Conseils de

dépannage

Instructions

de montage

Entretien et

nettoyage

Consignes

d’utilisation

Consignes

de sécurité

20

Consignes

de sécurité

Consignes

d’utilisation

Entretien et

nettoyage

Instructions

de montage

Conseils de

dépannage

Assistance à

la clientèle

A propos des commandes du climatiseur

Les fonctions et l’aspect peuvent varier.

Commandes (sur certains modèles)

Commandes du mode

Les réglages High Cool (fort refroidissement)

et Low Cool (refroidissement faible) fournissent

des refroidissements à des vitesses différentes

pour le ventilateur.

Les réglages du ventilateur permettent aussi de

filtrer et de faire circuler l’air sans le refroidir.

REMARQUE : Si vous passez d’un mode de

refroidissement sur Arrêt ou à un mode de

ventilation, attendez au moins 3 minutes avant

de repasser à un mode de refroidissement.

Descriptions du Refroidissement

Pour un refroidissement Normal—Sélectionnez

High Cool ou Low Cool avec un réglage sur une

température moyenne.

Pour un refroidissement Maximal—Sélectionnez

High Cool avec un réglage de la température sur

le chiffre le plus élevé.

Pour un Refroidissement plus Silencieux ou

Durant la Nuit—Sélectionnez le mode Low Cool

avec un réglage sur une température moyenne.

Contrôle de la TEMP

Le contrôle de la température est utilisé pour

maintenir la température de la pièce. Le

compresseur se met en marche et s’arrête

à intervalles réguliers pour maintenir la pièce

à un niveau de confort constant. Lorsque

vous tournez le bouton sur une valeur plus

élevée, l’air ambiant se refroidira. Lorsque vous

tournez le bouton sur une valeur plus basse, l’air

ambiant se réchauffera.

COMMANDES DU MODE

COMMANDES DE LA TEMPÉRATURE

La page est en cours de chargement...

GE AEY05LN Le manuel du propriétaire

Ce manuel convient également à

GE AEY05LN Le manuel du propriétaire

dans d''autres langues

Documents connexes