Texas Instruments TPS92410EVM-001 Manuel utilisateur

Marque: Texas Instruments

Modèle: TPS92410EVM-001

Catégorie: Régulateurs de tension

Taper: Manuel utilisateur

TPS92410EVM-001 Offline LED Driver

Evaluation Module

User's Guide

Literature Number: SLVUA49

April 2014

Contents

1 Introduction......................................................................................................................... 4

2 Warnings and Cautions ........................................................................................................ 4

3 Description.......................................................................................................................... 5

3.1 Typical Applications...................................................................................................... 5

3.2 Connector Descriptions ................................................................................................. 5

4 Electrical Performance Specifications .................................................................................... 6

5 TPS92410EVM-001 Schematic................................................................................................ 7

6 Performance Data and Typical Characteristic Curves............................................................... 8

6.1 Power Factor.............................................................................................................. 8

6.2 Line Regulation........................................................................................................... 8

6.3 Input Voltage and Input Current........................................................................................ 9

6.4 Linear Regulator Drain Voltage and Input Current................................................................... 9

6.5 Output Current .......................................................................................................... 10

6.6 Drain Overvoltage (DOV) Event (80-V Stack Shorted then Released).......................................... 10

6.7 Triac Dimming Waveforms ............................................................................................ 11

6.8 EMI Performance ....................................................................................................... 14

7 TPS92410EVM-001 PCB Layout............................................................................................ 15

8 Bill of Materials .................................................................................................................. 16

2Table of Contents SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

List of Figures

1 TPS92410EVM-001 Schematic............................................................................................ 7

2 Power Factor Versus Input Voltage ....................................................................................... 8

3 Input (Linear Regulator) Current Versus Input Voltage................................................................. 8

4 Input Voltage (Top) and Input Current (Bottom)......................................................................... 9

5 Drain Voltage (Top) and Input Current (Bottom)......................................................................... 9

6 80-V Stack (Top), 40-V Stack (Middle), and 20-V Stack (Bottom)................................................... 10

7 Drain Voltage (Top), DOV Pin Voltage (Middle), and Input Current (Bottom)...................................... 10

8 Forward Phase Triac Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Full............... 11

9 Forward Phase Triac Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Half .............. 11

10 Forward Phase Triac Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Low.............. 12

11 Reverse Phase Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Full ..................... 12

12 Reverse Phase Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Half..................... 13

13 Reverse Phase Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Low..................... 13

14 Conducted EMI Performance............................................................................................. 14

15 Top Layer and Top Overlay (Top View)................................................................................. 15

16 Bottom Layer and Bottom Overlay (Bottom View) ..................................................................... 15

List of Tables

1 TPS92410EVM-001 Electrical Performance Specifications............................................................ 6

2 TPS92410EVM-001 Bill of Materials..................................................................................... 16

SLVUA49–April 2014 List of Figures

User's Guide

SLVUA49–April 2014

Switch Controlled Direct Drive Linear Controller for Offline

LED Drivers

1 Introduction

The TPS92410EVM-001 evaluation module (EVM) helps designers evaluate the operation and

performance of the TPS92410 direct drive linear controller designed for use with the TPS92411 in offline

LED-drive applications. The TPS92410 is designed to control the drive of high-brightness light emitting

diodes (LEDs) and features a wide input voltage range (9.5 V to 400 V), thermal foldback, analog dimming

capability, and linear FET overvoltage protection.

2 Warnings and Cautions

Observe the following precautions when using the TPS92410EVM-001.

WARNING

High Voltage

CAUTION

DO NOT STARE DIRECTLY INTO THE LED LIGHT SOURCE.

Intense light sources have a high secondary blinding effect. A temporary

reduction in visual acuity and afterimages can occur, leading to irritation,

annoyance, visual impairment, and even accidents – depending on the

situation. Always consider the use of light filtering and darkening protective

eyewear and be fully aware of surrounding laboratory type set-ups when

viewing intense light sources to minimize or eliminate such risks in order to

avoid accidents related to temporary blindness.

WARNING

Do not stare at the operating LED – (Risk Group 1

(RG1)). See IEC32471-1 ed1.0:2009-08 for risk group definitions.

4Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

Description

3 Description

The TPS92410EVM-001 provides a high-brightness LED driver based on the TPS92410 in conjunction

with the TPS92411 direct drive switch. It is designed to operate with an input voltage in the range of 90

VAC to 135 VAC with a 120 VAC nominal input voltage. This input voltage range is typical for offline

applications. The EVM is set up for a default input current of 58 mA for 6.8 W total power and 3 LED

voltage stacks of 20 V, 40 V, and 80 V. The TPS92410 helps provide high efficacy, good power factor, low

THD, and flicker-free triac and phase dimming, due to its dimmer detect function that switches the input

current mode to a DC level.

3.1 Typical Applications

This converter design describes an application of the TPS92410 as an LED driver controller with the

specifications listed in Section 4. For applications with a different input voltage range or different output

voltage range, refer to the TPS92410 datasheet (SLUSBW9) and TPS92411 datasheet (SLUSBQ6).

3.2 Connector Descriptions

This section describes the connectors and test points on the EVM and how to properly connect, setup,

and use the TPS92410EVM-001.

3.2.1 J1

The screw down connector J1 is for the input voltage supply to the LED driver. The leads to the input

supply should be twisted and kept as short as possible to minimize voltage drop, inductance, and EMI

transmission. The input is not polarized. Line and neutral may be connected to either terminal.

3.2.2 VPx, VSx, ISx

The test points VP1, VS1, IS1, VP2, VS2, IS2, VP3, VS3, and IS3 are for testing the different LED stack

voltages and currents. For example, connect a voltmeter from VP1 to IS1 across the 1-Ωresistor, R1, to

measure the current in the top (80 V) LED string (1 mV = 1 mA). Connect a voltmeter from VP1 to VS1 to

measure the top stack voltage. The middle and lower stack currents and voltages can be measured in the

same way using the test points labeled with 2 and 3, respectively.

3.2.3 ADIM

The test point ADIM connects directly to the ADIM pin of the TPS92410. The voltage range is 0 V to 3 V.

Applying a voltage between 1.5 V and 3 V allows the internal reference to take over, resulting in a 1.5-V

reference at the CS pin. Applying a voltage below 1.5 V results in the applied voltage being the reference

at the CS pin down to 50 mV. Below 50 mV, the linear regulator is disabled and the GDL pin is pulled to

ground.

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

Electrical Performance Specifications

www.ti.com

4 Electrical Performance Specifications

Table 1 contains the electrical performance specifications for the EVM.

Table 1. TPS92410EVM-001 Electrical Performance Specifications

Parameter Test Conditions MIN TYP MAX Units

Input Characteristics

Voltage range 90 120 135 VAC

Maximum input current 58 mA

Output Characteristics

Output voltage, VOUT Upper LED stack 80 V

Middle LED stack 40

Lower LED stack 20

Flicker Index 0.03

Output current ripple percent 12 %

Output current ripple Each stack 23 mApp

Overvoltage protection level Each individual TPS92410 100 V

Linear FET overvoltage protection 51 V

level

Systems Characteristics

Efficiency Input voltage = 120 VAC, No triac dimmer 79.5 %

Power factor Input voltage = 120 VAC, No triac dimmer 0.99

THD Input voltage = 120 VAC, No triac dimmer 7.5 %

6Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

TPS92410EVM-001 Schematic

5 TPS92410EVM-001 Schematic

Figure 1 illustrates the TPS92410EVM-001 schematic.

Figure 1. TPS92410EVM-001 Schematic

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

90 95 100 105 110 115 120 125 130 135

Input Current (mA)

Input Voltage (VAC)

C001

0.98

0.982

0.984

0.986

0.988

0.99

0.992

0.994

0.996

0.998

90 95 100 105 110 115 120 125 130 135

Power Factor

Input Voltage (VAC)

C002

Performance Data and Typical Characteristic Curves

www.ti.com

6 Performance Data and Typical Characteristic Curves

Figure 2 through Figure 13 present typical performance curves for the TPS92410EVM-001.

6.1 Power Factor

Figure 2. Power Factor Versus Input Voltage

6.2 Line Regulation

Figure 3. Input (Linear Regulator) Current Versus Input Voltage

8Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

Performance Data and Typical Characteristic Curves

6.3 Input Voltage and Input Current

Figure 4. Input Voltage (Top) and Input Current (Bottom)

6.4 Linear Regulator Drain Voltage and Input Current

Figure 5. Drain Voltage (Top) and Input Current (Bottom)

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

Performance Data and Typical Characteristic Curves

www.ti.com

6.5 Output Current

Figure 6. 80-V Stack (Top), 40-V Stack (Middle), and 20-V Stack (Bottom)

6.6 Drain Overvoltage (DOV) Event (80-V Stack Shorted then Released)

Figure 7. Drain Voltage (Top), DOV Pin Voltage (Middle), and Input Current (Bottom)

10 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

Performance Data and Typical Characteristic Curves

6.7 Triac Dimming Waveforms

Figure 8. Forward Phase Triac Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Full

Figure 9. Forward Phase Triac Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Half

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

Performance Data and Typical Characteristic Curves

www.ti.com

Figure 10. Forward Phase Triac Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Low

Figure 11. Reverse Phase Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Full

12 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

Performance Data and Typical Characteristic Curves

Figure 12. Reverse Phase Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Half

Figure 13. Reverse Phase Dimming: Rectified Input Voltage (Top) and Input Current (Bottom) – Low

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

Performance Data and Typical Characteristic Curves

www.ti.com

6.8 EMI Performance

Figure 14 shows the conducted EMI performance of the EVM under the following conditions:

• PIN = 6.8 W

• VIN = 120 VAC

•QP = quasi-peak limit line

•A= average limit line

• Blue trace = peak scan

• Black trace = average scan

Figure 14. Conducted EMI Performance

14 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

TPS92410EVM-001 PCB Layout

7 TPS92410EVM-001 PCB Layout

Figure 15 and Figure 16 show the design of the TPS92410EVM-001 printed circuit board.

Figure 15. Top Layer and Top Overlay (Top View)

Figure 16. Bottom Layer and Bottom Overlay (Bottom View)

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

Bill of Materials

www.ti.com

8 Bill of Materials

Table 2 contains the TPS92410EVM-001 components list according to the schematic shown in Figure 1.

Table 2. TPS92410EVM-001 Bill of Materials

Reference Designator QTY Value Description Size Part Number MFR

C1 1 0.047µF CAP, Film, 0.047µF, 250VDC Radial B32529C3473K189 EPCOS Inc

C2 1 0.15µF CAP, Film, 0.15µF, 250VDC Radial B32529C3154J EPCOS Inc

C3 1 33µF CAP, AL, 33µF, 100V, +/-20%, 0.45 ohm 8x15mm UPW2A330MPD6 Nichicon

C4 1 68µF CAP, AL, 68µF, 50V, +/-20%, 0.234 ohm 8x11.5mm EEU-FC1H680 Panasonic

C5, C9 2 0.1µF CAP, CERM, 0.1µF, 16V, +/-5%, X7R 0603 C0603C104J4RACTU Kemet

C6 1 10µF CAP, CERM, 10µF, 25V, +/-10%, X7R 1206 GRM31CR71E106KA12L MuRata

C7, C12 2 1µF CAP, CERM, 1µF, 16V, +/-10%, X7R 0603 C1608X7R1C105K TDK

C8, C11 2 4.7µF CAP, CERM, 4.7µF, 16V, +/-10%, X5R 0603 GRM188R61C475KAAJ MuRata

C10 1 1000pF CAP, CERM, 1000pF, 50V, +/-10%, X7R 0603 GRM188R71H102KA01D MuRata

C13 1 120µF CAP, AL, 120µF, 25V, +/-20%, 0.23 ohm 6.3x15mm UPW1E121MED Nichicon

D1, D15, D22 3 200V Diode, Switching, 200V, 0.2A SOT-23 BAS21-7-F Diodes Inc.

D2, D3, D4, D5, D6, D7, D9, D10, D11, 21 Cool White LED, Cool White, SMD 3x.75x5.2mm SAW8KG0B-Y1Z4-CA Seoul Semiconductor

D12, D13, D14, D16, D17, D18, D19,

D20, D21, D23, D24, D25

D8 1 Diode, Switching-Bridge, 600V, 0.8A MiniDIP HD06-T Diodes Inc.

D26 1 100V Diode, Ultrafast, 100V, 0.15A SOD-123 1N4148W-7-F Diodes Inc.

J1 1 2x1 Conn Term Block, 2POS, 5.08mm 2POS Terminal 1715721 Phoenix Contact

Block

Q1 1 600V MOSFET, N-CH, 600V, 2A DPAK AOD2N60 AOS

R1, R5, R14 3 1.00ΩRES, 1.00 ohm, 1%, 0.125W 0805 RMCF0805FT1R00 Stackpole Electronics Inc

R2 1 442 ΩRES, 442 ohm, 1%, 1W 2512 CRCW2512442RFKEG Vishay-Dale

R3 1 1.82MΩRES, 1.82Meg ohm, 1%, 0.125W 0805 CRCW08051M82FKEA Vishay-Dale

R4, R7, R8, R9, R23 5 1.00MΩRES, 1.00Meg ohm, 1%, 0.25W 1206 CRCW12061M00FKEA Vishay-Dale

R6 1 1.65MΩRES, 1.65Meg ohm, 1%, 0.1W 0603 CRCW06031M65FKEA Vishay-Dale

R10, R11 2 2.00MΩRES, 2.00Meg ohm, 1%, 0.125W 0805 CRCW08052M00FKEA Vishay-Dale

R12, R18 2 30.1kΩRES, 30.1k ohm, 1%, 0.1W 0603 CRCW060330K1FKEA Vishay-Dale

R13 1 200kΩRES, 200k ohm, 1%, 0.1W 0603 CRCW0603200KFKEA Vishay-Dale

R15 1 54.9kΩRES, 54.9k ohm, 1%, 0.1W 0603 CRCW060354K9FKEA Vishay-Dale

R16 1 10.0ΩRES, 10.0 ohm, 1%, 0.1W 0603 CRCW060310R0FKEA Vishay-Dale

R19 1 121kΩRES, 121k ohm, 1%, 0.1W 0603 CRCW0603121KFKEA Vishay-Dale

R20 1 1.43MΩRES, 1.43Meg ohm, 1%, 0.1W 0603 CRCW06031M43FKEA Vishay-Dale

R21 1 30.1ΩRES, 30.1 ohm, 1%, 0.25W 1206 CRCW120630R1FKEA Vishay-Dale

R22 1 182ΩRES, 182 ohm, 1%, 0.25W 1206 CRCW1206182RFKEA Vishay-Dale

RF1 1 47ΩRES, 47 ohm, 10%, 2W Axial EMC2-47RKI TT Electronics/Welwyn

RT1 1 470kΩThermistor NTC, 470k ohm, 5% 0603 NCP18WM474J03RB MuRata

16 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers SLVUA49–April 2014

Submit Documentation Feedback

www.ti.com

Bill of Materials

Table 2. TPS92410EVM-001 Bill of Materials (continued)

Reference Designator QTY Value Description Size Part Number MFR

RV1 1 220V Varistor, 220V, 600A Disc 10x7mm ERZ-V05D221 Panasonic

U1, U2, U4 3 Switch Controlled Direct Drive Switch for Offline LED SOT23-5 TPS92411PDBV Texas Instruments

Drivers

U3 1 Switch Controlled Direct Drive Linear Controller for Offline SOIC-13 TPS92410D Texas Instruments

LED Drivers

R17 0 DNP

SLVUA49–April 2014 Switch Controlled Direct Drive Linear Controller for Offline LED Drivers

ADDITIONAL TERMS AND CONDITIONS, WARNINGS, RESTRICTIONS, AND DISCLAIMERS FOR

EVALUATION MODULES

Texas Instruments Incorporated (TI) markets, sells, and loans all evaluation boards, kits, and/or modules (EVMs) pursuant to, and user

expressly acknowledges, represents, and agrees, and takes sole responsibility and risk with respect to, the following:

1. User agrees and acknowledges that EVMs are intended to be handled and used for feasibility evaluation only in laboratory and/or

development environments. Notwithstanding the foregoing, in certain instances, TI makes certain EVMs available to users that do not

handle and use EVMs solely for feasibility evaluation only in laboratory and/or development environments, but may use EVMs in a

hobbyist environment. All EVMs made available to hobbyist users are FCC certified, as applicable. Hobbyist users acknowledge, agree,

and shall comply with all applicable terms, conditions, warnings, and restrictions in this document and are subject to the disclaimer and

indemnity provisions included in this document.

2. Unless otherwise indicated, EVMs are not finished products and not intended for consumer use. EVMs are intended solely for use by

technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical

mechanical components, systems, and subsystems.

3. User agrees that EVMs shall not be used as, or incorporated into, all or any part of a finished product.

4. User agrees and acknowledges that certain EVMs may not be designed or manufactured by TI.

5. User must read the user's guide and all other documentation accompanying EVMs, including without limitation any warning or

restriction notices, prior to handling and/or using EVMs. Such notices contain important safety information related to, for example,

temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or

contact TI.

6. User assumes all responsibility, obligation, and any corresponding liability for proper and safe handling and use of EVMs.

7. Should any EVM not meet the specifications indicated in the user’s guide or other documentation accompanying such EVM, the EVM

may be returned to TI within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE

EXCLUSIVE WARRANTY MADE BY TI TO USER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR

STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. TI SHALL

NOT BE LIABLE TO USER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RELATED TO THE

HANDLING OR USE OF ANY EVM.

8. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or

combination in which EVMs might be or are used. TI currently deals with a variety of customers, and therefore TI’s arrangement with

the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or

infringement of patents or services with respect to the handling or use of EVMs.

9. User assumes sole responsibility to determine whether EVMs may be subject to any applicable federal, state, or local laws and

regulatory requirements (including but not limited to U.S. Food and Drug Administration regulations, if applicable) related to its handling

and use of EVMs and, if applicable, compliance in all respects with such laws and regulations.

10. User has sole responsibility to ensure the safety of any activities to be conducted by it and its employees, affiliates, contractors or

designees, with respect to handling and using EVMs. Further, user is responsible to ensure that any interfaces (electronic and/or

mechanical) between EVMs and any human body are designed with suitable isolation and means to safely limit accessible leakage

currents to minimize the risk of electrical shock hazard.

11. User shall employ reasonable safeguards to ensure that user’s use of EVMs will not result in any property damage, injury or death,

even if EVMs should fail to perform as described or expected.

12. User shall be solely responsible for proper disposal and recycling of EVMs consistent with all applicable federal, state, and local

requirements.

Certain Instructions. User shall operate EVMs within TI’s recommended specifications and environmental considerations per the user’s

guide, accompanying documentation, and any other applicable requirements. Exceeding the specified ratings (including but not limited to

input and output voltage, current, power, and environmental ranges) for EVMs may cause property damage, personal injury or death. If

there are questions concerning these ratings, user should contact a TI field representative prior to connecting interface electronics including

input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or inaccurate

operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the applicable EVM user's guide prior

to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During

normal operation, some circuit components may have case temperatures greater than 60°C as long as the input and output are maintained

at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass

transistors, and current sense resistors which can be identified using EVMs’ schematics located in the applicable EVM user's guide. When

placing measurement probes near EVMs during normal operation, please be aware that EVMs may become very warm. As with all

electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in

development environments should use EVMs.

Agreement to Defend, Indemnify and Hold Harmless. User agrees to defend, indemnify, and hold TI, its directors, officers, employees,

agents, representatives, affiliates, licensors and their representatives harmless from and against any and all claims, damages, losses,

expenses, costs and liabilities (collectively, "Claims") arising out of, or in connection with, any handling and/or use of EVMs. User’s

indemnity shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if EVMs fail to perform as

described or expected.

Safety-Critical or Life-Critical Applications. If user intends to use EVMs in evaluations of safety critical applications (such as life support),

and a failure of a TI product considered for purchase by user for use in user’s product would reasonably be expected to cause severe

personal injury or death such as devices which are classified as FDA Class III or similar classification, then user must specifically notify TI

of such intent and enter into a separate Assurance and Indemnity Agreement.

RADIO FREQUENCY REGULATORY COMPLIANCE INFORMATION FOR EVALUATION MODULES

Texas Instruments Incorporated (TI) evaluation boards, kits, and/or modules (EVMs) and/or accompanying hardware that is marketed, sold,

or loaned to users may or may not be subject to radio frequency regulations in specific countries.

General Statement for EVMs Not Including a Radio

For EVMs not including a radio and not subject to the U.S. Federal Communications Commission (FCC) or Industry Canada (IC)

regulations, TI intends EVMs to be used only for engineering development, demonstration, or evaluation purposes. EVMs are not finished

products typically fit for general consumer use. EVMs may nonetheless generate, use, or radiate radio frequency energy, but have not been

tested for compliance with the limits of computing devices pursuant to part 15 of FCC or the ICES-003 rules. Operation of such EVMs may

cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may

be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: For EVMs including a radio, the radio included in such EVMs is intended for development and/or

professional use only in legally allocated frequency and power limits. Any use of radio frequencies and/or power availability in such EVMs

and their development application(s) must comply with local laws governing radio spectrum allocation and power limits for such EVMs. It is

the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations.

Any exceptions to this are strictly prohibited and unauthorized by TI unless user has obtained appropriate experimental and/or development

licenses from local regulatory authorities, which is the sole responsibility of the user, including its acceptable authorization.

U.S. Federal Communications Commission Compliance

For EVMs Annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications could void the user's authority to operate the equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at its own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Compliance (English)

For EVMs Annotated as IC – INDUSTRY CANADA Compliant:

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs Including Radio Transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Concerning EVMs Including Detachable Antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum

permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Canada Industry Canada Compliance (French)

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain

maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à

l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel

d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

spacer

Important Notice for Users of EVMs Considered “Radio Frequency Products” in Japan

EVMs entering Japan are NOT certified by TI as conforming to Technical Regulations of Radio Law of Japan.

If user uses EVMs in Japan, user is required by Radio Law of Japan to follow the instructions below with respect to EVMs:

1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and

Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of

Japan,

2. Use EVMs only after user obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or

3. Use of EVMs only after user obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect

to EVMs. Also, do not transfer EVMs, unless user gives the same notice above to the transferee. Please note that if user does not

follow the instructions above, user will be subject to penalties of Radio Law of Japan.

http://www.tij.co.jp

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】本開発キットは技術基準適合証明を受けておりません。本製品の

ご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします

上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

La page charge ...

Texas Instruments TPS92410EVM-001 Manuel utilisateur

Marque: Texas Instruments

Modèle: TPS92410EVM-001

Catégorie: Régulateurs de tension

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Texas Instruments TPS92410EVM-001 User manual

Texas Instruments TPS92410EVM-001 Manuel utilisateur

Texas Instruments TPS92410EVM-001 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents