Polaris Pool Alpha iQ Le manuel du propriétaire

Owner’s Manual

Manuel du propriétaire

El manual del propietario

Robotic Pool Cleaner

Models: ALPHATM iQ+, ALPHA iQ

VRXTM iQ+, VRX iQ

PHENOMTM iQ+

TYPE EC27--

WARNING

WARNING – For anything other than the routine cleaning and maintenance described in this guide, this product must be serviced by a qualiﬁed professional with sufﬁcient experience

in pool equipment installation and maintenance so that all of the instructions in the product’s complete installation and operations manual can be followed exactly. All safety

instructions in the complete manual must be followed explicitly in order to prevent injury hazards. Improper installation and/or operation may void the warranty. Never turn the cleaner

on unless it is fully submerged in the water. Doing so may void the warranty and may cause severe damage to the cleaner motors.

Page 2

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

FCC Statement

This device complies with Part 15 of the FCC Rules and IC license-exempt RSS standard. Operation is

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception which can be

determined by turning the equipment off and on, the user is encouraged to try to correct interference by one

or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modiﬁcations not expressly approved by the part responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This device complies with FCC and IC RF radiation exposure limits set forth for general population. This

device must be installed to provide a separation distance of at least 20 cm from all persons and must not be

co-located or operating in conjunction with any other antenna or transmitter.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential

radio interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

THANK YOU FOR PURCHASING THE POLARIS CLEANER.

YOUR POLARIS ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED AND TO PROVIDE LOW

MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW POLARIS CLEANER, PLEASE DO THE FOLLOWING:

1) Complete and return the warranty registration card.

2) Record your purchase information on the spaces provided below.

3) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please contact your original dealer. If

the original dealer does not perform warranty service, please visit polarispool.com to locate an independent service company near you. If you are

unable to locate a service company, please call our Technical Support department at 1.800.822.7933.

RECORD YOUR POLARIS CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on robot-head)

City State/Province Zip/Postal Code

Page 3

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

Table of Contents

Section 1. Important Safety Instructions .........4

Section 2. Cleaner Speciﬁcations ....................5

Section 3. Getting Started .................................5

3.1 Contents .........................................................5

3.2 Connect to a Power Source ........................... 5

Section 4. General Cleaner Operation .............7

4.1 Install and Submerge the Cleaner ..................7

4.2 Using the Control Box .................................... 8

4.3 Start / Stop Cleaning and

Adjust Cleaning Time .....................................9

4.4 Lift System ...................................................10

Section 5. Installing iAquaLink® .....................10

5.1 Download the App .......................................10

5.2 Sign Up and Log In ......................................10

5.3 Add to Mobile App System ..........................11

Section 6. iAquaLink® Control ........................11

6.1 iAquaLink Control Home Screen ..................11

6.2 Start / Stop Cleaning and

Adjust Cleaning Time ...................................12

6.3 Set Cleaning Mode .......................................12

6.4 Remote Control ............................................12

6.5 Lift System ...................................................12

6.6 Program or Cancel Cleaning Schedules

(not available on all models) ......................... 13

6.7 Temperature Display

(not available on all models) ......................... 13

6.8 LED Lights ....................................................13

6.9 In-App Error Messages

and Troubleshooting .....................................13

6.10 System Settings ...........................................13

Section 7. Maintenance ...................................14

7.1 Cord Tangling ...............................................14

7.2 Clean the Filter Canister ...............................15

7.3 Store the Cleaner When Not in Use .............16

7.4 Replacing Worn Parts ..................................16

7.5 Spare Parts...................................................19

Section 8. Troubleshooting .............................20

8.1 Error Codes ..................................................20

8.2 General Troubleshooting ..............................21

8.3 Dismissing an Error Code ............................22

8.4 iAquaLink Troubleshooting ...........................22

Page 4

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

Section 1. Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

Please read through the entire manual before installing your new robotic pool cleaner. The cleaner must be

installed and operated as speciﬁed.

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle should be provided by a qualiﬁed

installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset

button. Powershould be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump

without the test button being pushed, a ground current is ﬂowing, indicating the possibility of an electric shock. Do not use this product.

Disconnect the cleaner and have the problem corrected by a qualiﬁed service representative before using.

• Per the United States National Electrical Code®

(NEC®), keep the control box at least ﬁve (5) feet from the edge of the (pool/spa) water. In

Canada, the Canadian Electrical Code (CEC) requires a minimum distance of 3 m (10 ft) to be maintained between the pool edge and the

control box. Neversubmerge the control box.

• Do not enter pool while the cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and other equipment.

• To reduce the risk of electrical shock, do not use the robotic cleaner or control box if the cord is worn or damaged. Contact Zodiac Pool

SystemsLLC. Technical Support immediately for proper servicing and replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical replacement parts when servicing. Do not

attempt repair of the robotic cleaner, control box, power cord, or ﬂoating cable.

• NEVER OPEN CONTROL BOX.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY; PROVIDE A PROPERLY LOCATED GFCI RECEPTACLE.

THECONTROL BOX SHOULD BE PLUGGED INTO THE GFCI RECEPTACLE BOX.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of your pool’s operational system.

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal injury.

• The cleaner must be installed and operated as speciﬁed.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A permanently-installed pool is constructed

in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable

of being readily disassembled for storage and reassembled to its original integrity.

• Clean the ﬁlter canister in the cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95° F (35° C) or below 55° F (13° C).

USE OF THE ROBOTIC CLEANER IN A VINYL LINER POOL

• Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objects coming into contact with

the vinyl surface, including pool brushes, pool toys, ﬂoats, fountains, chlorine dispensers, and automatic pool cleaners. Some vinyl liner

patterns can be seriously scratched or abraded simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during

the installation process or when it comes into contact with objects in the pool. Zodiac Pool Systems LLC is not responsible for, and the Limited

Warranty does not cover, pattern removal, abrasion or markings on vinyl liners.

SAVE THESE INSTRUCTIONS

Page 5

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

Section 2. Cleaner Speciﬁcations

Technical Speciﬁcations

The general speciﬁcations for the cleaner are as

follows:

Control Box Supply

Voltage 100-125 VAC, 60 Hz

Supply Voltage 30 V DC

Installed Load 150 W max

Cable Length 60 ft (18 m) or 70 ft (21 m)

depending on model

Cleaner Size (WxDxH) 16.9 x 18.9 x 10.6 in.

(43 x 48 x 27 cm)

Weight of Cleaner 21 lbs. (9.5 kg)

Packed Weight 42 lbs. (19 kg)

Filtration Single ﬁlter canister

Cycle Lengths Variable programming

The cleaner is a double-insulated product.

Adouble-insulated electrical appliance is one

which has been designed in such a way that it

does not require a safety connection to ground.

The basic requirement for double-insulation is that

no single failure can result in dangerous voltage

becoming exposed so that it might cause an

electric shock and that this is achieved without

relying on an earthed (grounded) metal casing. This

is achieved by having two (2) layers of insulating

material surrounding live parts or by using

reinforced insulation. Therefore, devices having

double-insulated construction, suchas this cleaner,

do not utilize a grounded (three-prong) cord/plug.

Section 3. Getting Started

3.1 Contents

The packaging should contain the following items:

• Robotic cleaner and ﬂoating cable

• Control box

3.2 Connect to a Power Source

WARNING

Failure to comply with the following warnings can result in permanent

injury, electrocution or drowning.

PREVENT ELECTRICAL SHOCK

U.S.: Per NEC®

requirements, keep the control box at least 5 ft.

(1.5m) from the edge of the pool.

CANADA: Per CEC requirements, keep the control box at least 3 m

(10 ft) from the edge of the pool.

Only connect the control box to a receptacle protected by a ground

fault circuit interrupter (GFCI). Contact a certiﬁed electrician if you

cannot verify that the receptacle is protected by a GFCI.

Do not use an extension cord to connect the control box.

Do not allow anyone to swim while the cleaner is in the pool.

The control box is water-resistant, not waterproof. In order to prevent

electrocution, never submerge the control box or leave exposed to

inclement weather.

1. Unscrew the protective cap for the ﬂoating

cable from the side of the control box by

turning counter-clockwise.

Figure 1. Remove Protective Cap

Page 6

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

2. Grip the notched end of the ﬂoating power

cable, insert into the control box, and turn

clockwise to tighten.

3. Plug the control box directly into a GFCI outlet.

DO NOT use an extension cord.

Figure 2. Connect Floating Cable

NOTE: To avoid damaging the power cable, do not try

to twist the entire cable housing.

NOTE: To avoid exposing the power cable connector

pins to water, be sure the connector is screwed

in all the way and there is no gap.

Page 7

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

Section 4. General Cleaner

Operation

CAUTION

To prevent damage to the cleaner, to adhere to the following

guidelines:

• Remove the cleaner from the pool after the cleaning cycle is

completed.

• Store out of direct sunlight or inclement weather.

• Never lift the cleaner out of the pool by the ﬂoating cable.

• Take additional care when lifting the cleaner out of the pool.

Itbecomes heavier when ﬁlled with water.

• Always remove the cleaner from pool when super chlorinating

or adding acid.

• Do not handle cleaner while it is in operation.

IMPORTANT

• Always fully submerge the cleaner head before you begin

operation.

• Clean the ﬁlter canister after each cleaning cycle.

• Do not leave your cleaner in the pool on a permanent basis.

• At the end of each cycle, remove the cleaner from the pool.

• Start at the cleaner head and untangle any coils in the cable

before storing the cleaner.

The robotic cleaner includes a safety feature that

automatically stops the cleaner if a cleaning cycle

starts but it is not submerged in water. For pools

equipped with a beach area, this safety feature is

programmed to drive the cleaner in reverse and

back into the pool when the impeller is out of the

water.

WARNING

• Do not use an extension cord.

• Do not enter pool while the robotic cleaner is in water.

4.1 Install and Submerge the Cleaner

1. With the control box plugged into a GFCI

outlet, spread the ﬂoating cable across the

pool deck until you reach the middle of the

pool length.

2. At the center point, submerge the cleaner in

the pool and hold in the vertical position to

release any air trapped inside.

1

Figure 3. Submerge the Cleaner Vertically

3. Ensure the unit sinks to the bottom of the pool

and does not ﬂoat.

2

Figure 4. Cleaner Sinking to the Bottom of the Pool

4. Place only enough ﬂoating cable in the water

to reach the farthest end of your pool from the

central point. Spread out the ﬂoating cable

ensuring there are no kinks or coils in the

cable.

NOTE: For optimal patterning and reduced tangling, the

ﬂoating cable should enter the water near the

middle of the pool length. Only place enough

cable in the water to reach the farthest point in

thepool.

Page 8

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

Max Floating

Cable Length

Caddy /

Control Box

Recommended Entry Point

Not Recommended

Cleaner

WARNING

Do not use an extension cord.

Figure 5. Pool Entry Point for Optimal Patterning

4.2 Using the Control Box

The control box can be used to initiate basic cleaning features and to connect the device to home

Wi-Fi. For more information on connecting your cleaner to Wi-Fi, see section Installing iAquaLink®.

ALPHA™ iQ+ / VRX™ iQ+ / PHENOM™ iQ+ VRX iQ / ALPHA iQ

Page 9

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

Control box receiving power

Start/Stop cleaning

Select cleaning mode

*Waterline (45 min) Waterline only

Quick Clean (1 h 15 min) Floor only

SMART Cycle

(Calculate custom clean duration)

Floor, Wall, Waterline

*Deep Clean (2 h 45 min)

Floor, Walls, Waterline, High Intensity

Dirty canister indicator

Remove cleaner from the pool

+ / - 15 minute increments

Initiate connection and set up

iAquaLink® control

Bluetooth® light indicator status:

BLINKING - searching for signal

SOLID - paired with phone

Wi-Fi light indicator status:

BLINKING - connected to router

SOLID - connected to the internet

*Set recurring cleaning:

Every: Day, 2 Days, or 3 Days

* not available on all models

4.3 Start / Stop Cleaning and Adjust

Cleaning Time

The factory default cleaning mode is SMART Cycle

(Floor, Wall, Waterline).

The ﬁrst use of SMART Cycle (duration: 2:30),

will automatically calculate the cleaner’s optimal

cleaning time for your pool. After the initial SMART

Cycle calculation, the optimal cleaning time is

saved for future use.

To recalculate the SMART Cycle setting, press and

hold the START/STOP button for 5 seconds.

Use to change cleaning surface setting.

Toggle between:

*Waterline (45 min) Waterline only

Quick Clean (1 h 15 min) Floor only

SMART Cycle

(Calculate custom clean duration)

Floor, Wall, Waterline

*Deep Clean (2 h 45 min)

Floor, Walls, Waterline, High Intensity

* not available on all models

1. With cleaner submerged in water, press

to begin operation.

Press again to interrupt and cancel an

in-progress cleaning cycle.

NOTE: At the beginning of each cleaning cycle,

the robot conﬁrms your pool parameters

(approximately 10minutes). During this time, the

cleaner does not climb to the waterline.

Press +/- buttons to increase or decrease cleaning

time in 15-minute increments.

- Minimum run time is 30 minutes.

- Maximum run time is 3 hours 30 minutes.

NOTE: The control box automatically goes into standby

mode after 5 minutes and the display screen

turns off. Press any key to exit standby mode

and view remaining cycle time. Cleaner will

continue to function in standby mode.

Page 10

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

4.4 Lift System

The Lift System is designed to assist in retrieving

the robot from the pool. Lift System can be

activated at any time during or after a cleaning

cycle.

1. Press

to begin the automated

procedure.

The screen displays when the

LiftSystem is in operation.

NOTE: To stop the procedure at any time, press and

release the button again.

2. Next, Press and HOLD

to rotate

thecleaner.

3. Once the cleaner is facing the wall of your

choice for retrieval, release the button.

4. Cleaner will drive forward and up the wall it

is facing. It will wait at the water line to be

retrieved.

5. When in reach, remove the cleaner from the

pool using the handle. The cleaner will quickly

expel water to allow for lighter, easier removal.

NOTE: Never lift the cleaner out of the pool by the

ﬂoating cable.

Section 5. Installing iAquaLink®

The iAquaLink app is available for download from

the App Store or Google Play.

With iAquaLink Control, you can connect to

your robotic cleaner from anywhere, anytime to

access functions and troubleshooting advice.

App features are dependent on model.

Before you begin installation, make sure you

have the following:

• IMPORTANT: Have your Wi-Fi network

password available

• Robotic cleaner is submerged in the pool

• Control box is connected and plugged into a

GFCIoutlet

• Smart device (phone or tablet) with Wi-Fi and

Bluetooth® enabled

• Wi-Fi router with sufﬁcient signal strength at

the control box

5.1 Download the App

Install or update the iAquaLink app from the App

Store or Google Play.

5.2 Sign Up and Log In

Open the iAquaLink app, then Sign Up or Log In.

Complete all required ﬁelds in the Account Setup

page and agree to the Terms and Conditions.

Page 11

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

5.3 Add to Mobile App System

1. On the My Systems page, click + in the upper

right-hand corner to add a system.

2. Choose “Robotic Cleaner”. Follow in app

instructions to add your cleaner and connect it

to your home router.

3. On the control box, press .

Bluetooth® light indicator status:

BLINKING - searching for signal

SOLID - paired with phone

Wi-Fi light indicator status:

BLINKING - connected to router

SOLID - connected to the internet

NOTE: Errors during connection may be the results of

insufﬁcient Wi-Fi signal strength at the control

box location. If you are unable to move the

control or router to improve signal strength,

you may need a Wi-Fi extender to boost your

signal strength. (SeeiAquaLink® Troubleshooting

section.)

NOTE: An incorrect password may also be that cause

of a connection error. If the signal strength at the

control box is good, double check the network

name and credentials for the router you are

trying to access.

Section 6. iAquaLink® Control

Once you have downloaded the iAquaLink app and

connected the device to Wi-Fi, the iAquaLink app

allows for robotic cleaner control from anywhere,

anytime. Functions vary within the iAquaLink app

depending on which cleaner model you have.

WARNING

Do not enter pool while the robotic cleaner is in water.

6.1 iAquaLink Control Home Screen

App function and design is subject to change.

Start/Stop Cleaning

Remote

Clean Mode

Lift System

Dirty Canister Indicator

+

–Manual Time Adjustment

(current run time +/- 15 minutes)

°F / C

Water Temperature Display

Page 12

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

6.2 Start / Stop Cleaning and Adjust

Cleaning Time

The factory default cleaning surface setting is

SMART Cycle (Floor, Wall, Waterline).

SMART Cycle calculates a customized cleaning

time optimized for your pool. On the ﬁrst run of

SMART Cycle, the app counts up as it calculates

the optimized cleaning time.

On periodic SMART Cycle cleaning, the app will

count down from the optimized cleaning time.

NOTE: To Recalculate SMART Cycle, go to the Set

Cleaning Mode after the initial calculation.

1. From the Home screen or the control box,

press the Start button to begin cleaning.

2. The app displays the cycle time in hours and

minutes.

To increase or decrease the cycle time during

cleaning, press the (+) and (–) buttons.

—Time adjusts up or down in 15 minute

increments.

—Minimum run time is 30 minutes.

—Maximum run time is 3 hours 30 minutes.

—The control box displays the same

countdown and cycle setting as the app.

3. Press to interrupt and cancel an

in-progress cleaning cycle.

NOTE: At the beginning of each cleaning cycle,

the robot conﬁrms your pool parameters

(approximately 10minutes). During this time, the

cleaner does not climb to the waterline.

6.3 Set Cleaning Mode

1. From the main screen, select Cleaning Mode

to view options.

2. Choose from available cleaning modes

depending on your cleaner model.*

3. In Custom mode (if applicable), select the

cleaning surface and cleaning intensity from

the on-screen icons.

*not available on all models

6.4 Remote Control

Use your mobile device as a remote control.

IMPORTANT

Only use remote control when in view of the cleaner.

1. From the main screen, select the Remote tab.

NOTE: When in remote control mode, the control box

displays .

2. You can direct the cleaner using the remote

control or use the spot clean feature to help

pick up debris.*

3. To use “Spot Clean” drive the cleaner near

where debris has collected and initiate “Spot

Clean.” The Cleaner will perform a short

cleaning pattern to remove debris in that area.

*not available on all models

NOTE: If you experience signiﬁcant delays between the

app command and cleaner response, you may

have a weak Wi-Fi signal or other connectivity

challenges that interfere with the immediacy of

the remote control functions.

6.5 Lift System

The Lift System is designed to assist in retrieving

the robot from the pool. Lift System can be

activated at any time during or after a cleaning

cycle.

IMPORTANT

Only use Lift System when in view of the cleaner.

1. From the home screen, select Lift System

to enter automated procedure.

2. Use the left and right controls to rotate the

cleaner to face the wall of your choice.

3. Press the Lift System icon to drive the cleaner

up the wall it is facing. The cleaner will wait at

the water line to be retrieved.

NOTE: To stop the procedure at any time, press and

release the button again.

4. When in reach, grab the cleaner handle and

begin to pull cleaner out of the water. The

cleaner will quickly expel water to allow for

lighter, easier removal.

NOTE: Never lift the cleaner out of the pool by the

ﬂoating cable.

Page 13

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

6.6 Program or Cancel Cleaning

Schedules

(not available on all models)

It is still recommended to remove and clean the

ﬁlter canister after every cleaning cycle.

1. Tap the area titled Next Cleaning or go

to System Settings and choose

Schedules.

2. To program a schedule, select the day of the

week.

3. Select a start time to begin the cleaning cycle.

4. Select a cleaning mode. Mode selected will

determine runtime.

5. Press OK to save the schedule or Delete to

remove permanently.

6. Repeat steps 2-4 to program additional days.

NOTE: Only one programmed cleaning cycle can be

scheduled per day.

7. Press BACK or DONE to leave the Edit

Schedule page and return to the main screen.

8. The next scheduled cleaning cycle will display

near the top of the main screen.

6.7 Temperature Display

(not available on all models)

On some models, the pool water temperature will

be displayed on the main app screen. Accurate

temperature may take a few minutes to display as

the sensor acclimates to the surrounding water

temperature. Temperature will only be displayed

during an in-progress cleaning cycle.

6.8 LED Lights

1. Sensor Nav System™ - Indicator Light:

Located on the front of the cleaner, this light

has several functions to indicate status:

Blinking Blue: Sensing, Scanning and

Cleaning

*Solid Blue: Cleaning

Blinking Green: Lift System or Spot Cleaning

Solid Green: Remote Control

2. On some models, an LED light illuminates the

interior area of the body and canister.

*not available on all models

NOTE: LED lights may be difﬁcult to see in sunlight.

6.9 In-App Error Messages and

Troubleshooting

If an error occurs, the status bar will show a

warning symbol and: “Cleaning Interrupted”.

1. Click on the warning symbol to view

troubleshooting advice on how to ﬁx the issue.

2. Choose Clear Error if you believe you have

ﬁxed the problem and want to re-try. Choose

OK if you want to suspend the cleaner in error

mode and work on the troubleshooting ﬁx at a

later time.

6.10 System Settings

Access System Settings by pressing the gear icon

in the upper right hand corner of the app screen.

Page 14

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

Section 7. Maintenance

WARNING

To avoid electric shock and other hazards which could result in

permanent injury or death, disconnect (unplug) the cleaner from the

power source before performing any cleaning and maintenance.

7.1 Cord Tangling

Tangling can occur more frequently when the

cleaner is not attended to after each cleaning

cycle. The tangle-reducing swivel, in addition to

proper installation, general maintenance and the

following troubleshooting steps can help to avoid

cable challenges.

IMPORTANT

Cleaner power cable may become tangled if correct procedure is

not followed after each cleaning cycle.

NOTE: For optimal patterning and reduced tangling, the

ﬂoating cable should enter the water near the

middle of the pool length. Only place enough

cable in the water to reach the farthest point in

thepool.

Caddy /

Control Box

Not Recommended

Cleaner

WARNING

Do not use an extension cord.

Max Floating

Cable Length

Recommended

Entry Point

Figure 6. Optimal Entry Point in Pool

If tangling occurs, follow these steps:

1. Remove the cleaner from the pool using the

Lift System. When the cleaner is within arm’s

reach, use the handle to remove from the

water. Never lift the cleaner out of the pool by

the ﬂoating cable or swivel.

2. Hold the cleaner vertically to drain.

Figure 7. Keep Cleaner Vertical to Drain Water

3. Unplug power to the cleaner at the control

box.

Figure 8. Unplug

Page 15

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

4. Remove the cleaner from the pool and

untangle all kinks and coils in the power cable.

Start at the cleaner head. Lay the cable in the

sun to loosen any tangling memory.

Figure 9. Untangle

7.2 Clean the Filter Canister

The ﬁlter canister should be cleaned at the end of

each cycle.

1. Remove the cleaner from the water using the

Lift System and let the remaining water drain.

2. Set the unit on four wheels.

3. Push the cover lock (1) and lift the cover (2)

until it is secured in the vertical position.

2

1

Figure 10. Lift Cleaner Cover

4. Remove the ﬁlter canister assembly from the

body (3), as shown.

3

Figure 11. Remove Filter Canister Assembly

5. Push the quick release button on the canister

assembly (4) and pull open.

4

5

Figure 12. Open Filter Canister Assembly

6. Separate the ﬁlter canister from the ﬁlter

support (6), as shown.

6

Figure 13. Remove Filter Canister

Page 16

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

7. Empty all debris from the ﬁlter canister, then

rinse the canister, the ﬁlter support and the

cleaner using a hose, as shown.

Figure 14. Wash Filter Canister

NOTE: Periodically, remove the ﬁlter canister and clean

thoroughly with soapy water and a soft bristle

brush.

7.3 Store the Cleaner When Not in Use

The cleaner should be cleaned regularly using

slightly soapy clean water. Do not use solvents

such as trichlorethylene or its equivalent. Rinse the

cleaner generously using clean water. Do not let

your cleaner dry in direct sunlight near the pool.

Thecleaner should be stored on its caddy so that

itdries quickly.

1. Disconnect cleaner from the power source.

2. Starting at the cleaner head, remove all coils

and tangles from the cable. Lay the cable in

the sun to loosen any tangling memory.

3. Place the rear wheels on the caddy and

position the cleaner vertically on the caddy

base.

4. Disconnect the cable from the control box.

Replace the protective cap on the control box.

Figure 15. Untangle the Floating cable

5. Loosely coil the power cable starting at the

cleaner and moving toward the connection

pointat control box. Store the cable by

wrapping it around the hook located on the

frontof the caddy.

7.4 Replacing Worn Parts

Replacing Brushes

The cleaner is ﬁtted with PVC brushes with a

“wear’’ indicator.

raised groove becomes

partially flattened,

indicating excessive

wear

Raised groove

becomes

partially ﬂattened,

indicating

excessive wear.

Figure 16. Worn Brush Indicator

To maintain cleaner performance at its best you

need to replace the brushes as soon as one of the

wear indicators is reached (even if the blade wear

is not even). It is recommended that you replace

the brushes when the rubber is worn down to

the top of the wear indicator (or every two years,

whichever comes ﬁrst).

Page 17

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

To replace a worn brush:

1. Lift the cleaner to a vertical position so that the

handle is up.

1

Figure 17. Cleaner in Upright Position

2. Separate the edges of the brush and undo the

tabs. Remove the worn brushes.

2

Figure 18. Undo the Tabs of the Brush

3. To install the new brush, position the new

brush on the roller with the cleaning blades

facing away from the roller.

3

Figure 19. Install the New Brush

4. Thread each tab into the slot provided and

gently feed it through until the heel comes out

at the other side of the slot.

4

Figure 20. Pull Tabs Through Each Slot

5. Use a pair of scissors to cut the tabs 3/4 inch

from the heel so that they are no higher than

the cleaning blade.

6. Repeat the procedure to install the second

brush.

Figure 21. Cut Tabs

Page 18

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

Replacing Tires

1. Pull on the inside of the old tire to remove the

tire lip from the wheel.

1

Figure 22. Pull the Old Tire Over the Wheel

2. Remove the old tire.

2

Figure 23. Remove the Old Tire

3. To replace the tire, position the tire on the

wheel making sure to orient the tire so that the

word INSIDE is toward the body of the cleaner.

1

I

N

S

I

D

E

I

N

S

I

D

E

I

N

S

I

D

E

Word

“INSIDE”

Towards

Cleaner

Figure 24. Tire Replacement Orientation

4. Push one side of the tire on to the wheel and

ﬁt the rib of the tire in the groove of the wheel.

2

Figure 25. Start on One Side of the Tire

Page 19

Polaris® Robotic Pool Cleaner | Owner’s Manual ENGLISH

5. Work the tire onto the wheel and verify the

rib of the tire is positioned properly within the

groove of the wheel.

3

Figure 26. Work the Tire On Around the Wheel

6. Push and position the rib of the inner side of

the tire in the groove of the wheel. If needed,

turn the wheel gently to help with installation.

4

Figure 27. Push the Tire into Place on the Wheel

7.5 Spare Parts

The complete spare parts list and exploded view is

available on the Polaris website.

• USA: www.polarispool.com

• Canada: www.polarispool.ca

Contact your local maintenance provider to

perform diagnostic tests or repairs not shown in

general maintenance.

Page 20

ENGLISH Polaris® Robotic Pool Cleaner | Owner’s Manual

Section 8. Troubleshooting

Information about the cleaner status and any relevant condition will be displayed on the control box and/or

in the iAquaLink® app.

8.1 Error Codes

Control Box

Display In-App Display Suggested Solution

1

2

3

Pump Motor

Traction Motor Right

Traction Motor Left

a. Check for corrosion or bent pins in the power cable

connection area.

b. Turn each wheel one quarter turn in one direction

repeatedly until rotation is smooth. Repeat, turning wheels

in the opposite direction until rotation is smooth.

c. If this does not resolve the problem, contact your local

retailer for a diagnostic review or call customer service.

4Pump Motor Consumption a. Check for small debris or hair in the fan impeller.

b. Thoroughly clean the ﬁlter canister.

c. If this does not resolve the problem, contact your local

retailer for a diagnostic review or call customer service.

5

6

Drive Motor Consumption Right

Drive Motor Consumption Left

a. Thoroughly clean the ﬁlter canister.

b. Turn off the cleaner and submerge. Shake to release air

bubbles. Restart cycle.

c. If this does not resolve the problem, contact your local

retailer for a diagnostic review or call customer service.

7Cleaner Floating

• Turn cleaner power off, then submerge cleaner according to

correct procedure.

8Cleaner Out of the Water

• Turn off the cleaner and submerge. Shake to release air

bubbles. Restart cycle.

9N/A

• Cleaner has completed a cleaning cycle. This is not an error.

Noaction required.

10 Communication a. Turn cleaner power off and on again to reset.

b. Check ﬂoating cable connection to the control box.

Checkfor corrosion or bent pins at the connection point.

c. If this does not resolve the problem, contact your local

retailer for a diagnostic review or call customer service.

11 Sensor Unit

• Contact approved service station for replacement.

N/A Connection Error a. Check that the control box is plugged into a GFCI outlet

and that the Wi-Fi icon is illuminated.

b. If not, go through the set-up steps to reconnect to the

home router. Check that the router is in close enough range

to the control box. Install a Wi-Fi extender if necessary.

La page charge ...

Polaris Pool Alpha iQ Le manuel du propriétaire

Polaris Pool Alpha iQ Le manuel du propriétaire

dans d''autres langues

Autres documents