Polaris P935 Le manuel du propriétaire

9400

OWNER’S MANUAL

ENGLISH

|

FRANÇAIS

|

ESPAÑOL

AVERTISSEMENT

POUR VOTRE SÉCURITÉ – Pour toute opération autre que l’entretien de routine et la maintenance décrite dans ce manuel, ce produit doit

être pris en charge par une entreprise qui est autorisée et qualifiée pour la réparation des équipements de piscine par la juridiction où le

dit produit est installé lorsque de telles exigences locales ou provinciales sont édictées. Si aucune exigence locale ou provinciale n’est

disponible, l’agent d’entretien doit être un professionnel avec suffisamment d’expérience dans l’installation et la maintenance d’équipement

de piscine pour appliquer correctement les consignes du présent manuel. L’installation ou l’utilisation inappropriée annulera la garantie.

WARNING

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product must be serviced

by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state

or local requirements exist. In the event no such state or local requirement exists, the maintainer must be a professional with sufficient

experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Improper

installation and/or operation will void the warranty.

H0392900 Rev F

9350/9450/9550 Sport

P935/P945/P955

ADVERTENCIA

PARA SU SEGURIDAD – Este producto debe ser instalado y mantenido por un contratista que está autorizado y calificado en equipo de

piscina en las jurisdicción en la que el producto se instala donde existan requisitos estatales o locales. En el caso de ningún estado o

locales obligatorio, el responsable debe ser un profesional con experiencia suficiente en la piscina de la instalación y mantenimiento de

equipo para que todas las instrucciones en este manual puede ser seguido exactamente. Antes de instalar este producto, lea y siga todas

las advertencias y las instrucciones qu acompañan a este producto. El incumplimiento de los avisos de advertencia e instrucciones puede

resultar en daños a la propiedad, lesiones personales o la muerte. La instalación y/o operación se anulará la garantía.

TYPE EC27--

Page 2

English

THANK YOU FOR PURCHASING THE POLARIS CLEANER.

YOUR POLARIS ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED

AND TO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW POLARIS CLEANER,

PLEASE DO THE FOLLOWING:

1) Complete and return the warranty card.

2) Record your purchase information on the spaces provided below.

3) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please visit

www.polarispool.com to locate an independent service company near you. If you are unable to locate a service

company, please call our Technical Support department at 1-800-822-7933.

RECORD YOUR POLARIS CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on machine head)

City State/Province Zip/Postal Code

Table of Contents

Section 1. Important Safety Instructions ........ 4

Section 2. Cleaner Specications ................... 5

Section 3. Assembly ......................................... 5

3.1 Unpacking .......................................................... 5

3.2 Assembling the Transport Caddy ....................... 5

3.3 Connecting the Control Unit to the Caddy .......... 7

3.4 Connecting to Power Source .............................. 8

Section 4. Operation ......................................... 9

4.1 Submerging the Cleaner .................................... 9

4.2 The Polaris 9350/P935 Cleaner Control Unit ... 10

4.3 The Polaris 9450 Sport/P945 Cleaner Control

Unit ................................................................... 10

4.4 The Polaris 9550 Sport/P955 Cleaner

Control Unit .......................................................11

4.5 Starting the Cleaner ..........................................11

4.6 Stopping the Cleaner

and Removing from the Pool ............................ 12

4.7 Operating the Cleaner with the Remote Control

(9550 Sport/P955 only) .................................... 12

4.8 Synchronizing the Remote Control ................... 13

4.9 Storing the Cleaner ......................................... 13

Section 5. Programming the Cleaner.............. 14

5.1 Displaying Current Day and Time ..................... 14

5.2 Changing the Clock Day and Time ................... 14

5.3 Changing Default Cleaning Times .................... 14

5.4 Programming Cleaning Cycles ......................... 15

5.5 Canceling Cleaning Cycles .............................. 15

Section 6. Cleaning and Maintenance .......... 16

6.1 Cleaning the Filter Canister .............................. 16

6.2. Cord Tangling ................................................... 17

6.3 Replacing the Brushes ..................................... 18

6.4 Replacing the Tires ........................................... 19

Section 7. Spare Parts .................................... 20

Section 8. Troubleshooting ........................... 21

8.1 Using the Information LED for

Troubleshooting (9350 / P935 Cleaner) ........... 21

8.2 Viewing Cleaner Status Information for

Troubleshooting

(9450 Sport/P945 and 9550 Sport/P955) ......... 21

8.3 General Troubleshooting .................................. 22

8.4 Control Unit Error Codes

(9450 Sport/P945 and 9550 Sport/P955) ......... 23

Page 3

English

FCC Statement

This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction,

may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception which can be determined by turning the equipment

off and on, the user is encouraged to try to correct interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modications not expressly approved by by the part responsible for compliance could void

the user's authority to operate the equipment.

NOTE: This device complies with FCC and IC RF radiation exposure limits set forth for general population.

This device must be installed to provide a separation distance of at least 20cm from all persons and

must not be co-located or operating in conjunction with any other antenna or transmitter.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential

radio interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Page 4

English

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle should be provided by a qualified

installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset

button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump

without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this product.

Disconnect the cleaner and have the problem corrected by a qualified service representative before using.

• Per the United States National Electrical Code

®

(NEC

®

), keep the control unit at least five (5) feet from the edge of the (pool/spa) water. In

Canada, the Canadian Electrical Code (CEC) requires a minimum distance of 3m (10 ft.) to be maintained between the pool edge and the

control unit. Never submerge the control unit.

• Do not enter pool while the Polaris cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and other equipment.

• To reduce the risk of electrical shock, do not use the Polaris robotic cleaner or control unit if the cord is worn or damaged. Contact Zodiac Pool

Systems, Inc. Technical Support immediately for proper servicing and replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical replacement parts when servicing. Do not

attempt repair of the Polaris robotic cleaner, control unit, power cord, or floating cable.

• NEVER OPEN CONTROL UNIT.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY; PROVIDE A PROPERLY LOCATED GFCI

RECEPTACLE. THE CONTROL UNIT SHOULD BE PLACED NEAR THE GFCI RECEPTACLE BOX.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of your pool’s operational system.

Section 1. Important Safety Instructions

Congratulations on purchasing the Polaris Robotic Cleaner. Please read through the entire manual before installing

your new robotic pool cleaner. Your cleaner must be installed and operated as specified.

READ AND FOLLOW ALL INSTRUCTIONS

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal injury.

• The Polaris cleaner must be installed and operated as specified.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A permanently-installed pool is constructed

in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable

of being readily disassembled for storage and reassembled to its original integrity.

• Clean the filter canister in the Polaris cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

CAUTION

USE OF THE POLARIS ROBOTIC CLEANER IN A VINYL LINER POOL

Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objects coming into contact with

the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine dispensers, and automatic pool cleaners. Some vinyl liner

patterns can be seriously scratched or abraded simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during

the installation process or when it comes into contact with objects in the pool. Zodiac Pool Systems, Inc., is not responsible for, and the

Limited Warranty does not cover, pattern removal, abrasion or markings on vinyl liners.

SAVE THESE INSTRUCTIONS

Page 5

English

Section 2. Cleaner Specications

2.1 General Specications

The general specifications for the cleaner are as follows:

x 2

A

B

C

D

x 2

E

x 2

F

G

H

I

Figure 1. Transport Caddy Assembly Components

When unpacking the cleaner and its components:

• Check to make sure each component is in the box.

• Check cleaner and components for damage during

transport.

• If there are any missing parts or damage, contact

Zodiac

®

Technical Support at 1-800-822-7933.

3.2 Assembling the Transport Caddy

1. Unscrew the handnut from the base unit

(Figure 2).

Figure 2. Remove Handnut from Base Unit

2. Insert the metal handle frame tubing into the

base unit with notch end at the top, then rotate

so the bends are away from you. (Figure 3).

Control box

supply voltage

100-125 VAC, 60 Hz

Supply voltage 30 V DC

Installed load 150 W max

Cable length

9350/P935, 9450/P945:

60 ft (18 m)

9550/P955: 70ft (21m)

Cleaner size

(WxDxH)

16.9 x 18.9 x 10.6 in. (

43 x 48 x 27 cm)

Weight of Cleaner 21 lbs. (9.5 kg)

Packed weight 42 lbs. (19 kg)

Filtration

All-purpose lter canister

Cycle lengths Variable programming

The cleaner is a double-insulated product. A double-

insulated electrical appliance is one which has been

designed in such a way that it does not require a safety

connection to ground. The basic requirement for

double-insulation is that no single failure can result

in dangerous voltage becoming exposed so that it

might cause an electric shock and that this is achieved

without relying on an earthed (grounded) metal casing.

This is achieved by having two (2) layers of insulating

material surrounding live parts or by using reinforced

insulation. Therefore, devices having double-insulated

construction, such as this cleaner, do not utilize a

grounded (three-prong) cord/plug.

Section 3. Assembly

3.1 Unpacking

The packaging should contain the following items:

• Polaris cleaner

• Control unit

• Remote Control (9550 Sport/ P955 only)

• Transport and storage caddy assembly components

(Figure 1)

(a) handle frame

(b) support blocks (x 2)

(c) wheels (x 2)

(d) wheel locking clips (x 2)

(e) wheel axle / hubcap (x 2)

(f) base unit

(g) cleaner hook

(h) caddy handle

(i) remote control & attachment hook

(9550 Sport/ P955)

Page 6

English

3. Push base unit down (Figure 3) so the metal

handle frame is seated in the recess on the

underside of the base.

Figure 3. Connect Metal Frame to Base Unit

4. Slide the handnut over the tube and twist to

tighten onto base unit (Figure 4).

Figure 4. Twist Handnut to Secure Frame

5. Snap two (2) support blocks into place

(Figure 5).

6. Slide axle and hubcap piece through center of

wheel and attach to base unit. Snap locking clip

into place to secure wheel. Repeat to attach both

wheels (Figure 5).

Figure 5. Snap in Support Blocks and Attach

Wheels

7. Slide the control unit base / caddy handle

attachment down over the metal tubing until it

snaps into place. (See Figure 6).

Figure 6. Attach Caddy Handle

Page 7

English

Figure 9. Fully Assembled Transport Caddy

3.3 Connecting the Control Unit to the

Caddy

1. Align the bottom of the control unit with the

notch at bottom of the control unit hook on the

caddy (Figure 10).

Figure 10. Align Control Unit with Caddy Hook

2. Press control unit onto the caddy hook until it

snaps and locks into position (Figure 11).

8. Align cleaner hook pins with the top holes in

the handle tube and snap into place (Figure 7).

Figure 7. Snap Cleaner Hook into Place

9. (9550 Sport/P955) Locate pin on the remote

control holder and align it with the recepticle

on the handle of the caddy to attach the remote

control unit to caddy (Figure 8).

Figure 8. Snap Remote Control Holder into Place

Page 8

English

Figure 12. Remove Protective Cap

Figure 13. Connect Power Cable

2. Gripthenotchedendoftheoatingpower

cable, insert into the control unit, and turn

clockwise to tighten. (Figure 13.)

NOTE: To avoid damaging the power cable, do not try to

twist the entire cable housing (see below).

NOTE: To avoid exposing the power cable connector pins

to water, be sure the connector is screwed in all the

way and there is no gap. (see below).

Figure 11. Attach the Control Unit onto Caddy

3.4 Connecting to a Power Source

WARNING

Failure to comply with the following warnings can

result in permanent injury, electrocution or drowning.

PREVENT ELECTRICAL SHOCK

• U.S.: Per NEC

®

requirements, keep the control unit

at least five (5) ft. (1.5 m) from the edge of the pool.

CANADA: Per CEC

requirements, keep the control

unit at least three (3) m (10 ft.) from the edge of the

pool.

• Only connect the control unit to a receptacle

protected by a ground fault circuit interrupter

(GFCI). Contact a certified electrician if you cannot

verify that the receptacle is protected by a GFCI.

• Do not use an extension cord to connect the control

unit.

• Do not allow anyone to swim while the cleaner is in

the pool.

• The control unit is water-resistant, not waterproof.

In order to prevent electrocution, never submerge

the control unit or leave exposed to inclement

weather.

1. Unscrew the protective cap for the power cable

from the side of the control unit by turning

counter-clockwise (Figure 12).

Page 9

English

Section 4. Operation

CAUTION

To prevent damage to the cleaner, be sure to adhere

to the following guidelines:

• Remove the cleaner from the pool after the

cleaning cycle is completed and store on the caddy

out of direct sunlight or inclement weather.

• Never lift the cleaner out of the pool by the floating

cable. Always use the lift feature to remove cleaner

from the pool.

• Take additional care when lifting the cleaner out of

the pool. It becomes heavier when filled with water.

• Always remove the cleaner from pool when super

chlorinating or adding acid.

• Do not handle cleaner while it is in operation.

IMPORTANT

• Always make sure the cleaner head is fully

submerged before you begin operation.

• Clean the filter canister after each cleaning cycle.

• Do not leave your cleaner in the pool on a permanent

basis.

• At the end of each cycle, remove the cleaner from

the pool. Start at the cleaner head and untangle any

coils in the cable before storing the cleaner.

Whenthecontrolunitispoweredonwiththeoating

cable attached, the operating time for the current

selected cycle is displayed.

The Polaris robotic cleaner includes a safety feature

that automatically stops the cleaner if it is powered on

but not submerged in water. For pools equipped with a

beach area, this safety feature is programmed to drive

the cleaner in reverse and back into the pool when the

impeller is out of the water.

4.1 Submerging the Cleaner

1. Submerge the cleaner in the pool and remove

any air trapped inside by keeping the unit

vertical (Figure 15).

2. Ensure the unit sinks to the bottom of the pool

anddoesnotoat(Figure16).

1

Figure 15. Submerge the Cleaner Vertically

2

Figure 16. Cleaner Sinking to the Bottom of the

Pool

3. Spreadouttheoatingcableoverthepool,

ensuring there are no kinks or coils in the cable.

NOTE: For optimal patterning and reduced

tangling, the oating cable should enter the water

near the middle of the pool length. Only place

enough cable in the water to reach the farthest

point in the pool (see Figure 17).

Figure 17. Setup for Optimal Patterning

Max

Floating Cable

Length

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Page 10

English

4.2 The Polaris 9350/P935 Cleaner Control Unit

Select Cleaning Surface

• Bottom

• Bottom and Sides

Start/Stop Cleaner

Operation

Remove Cleaner

from Pool

Cleaner Error

Indicator

4.3 The Polaris 9450 Sport/P945 Cleaner Control Unit

Display Current

Time/ Set Time

Program Cleaning

Cycles / Set Time

Navigate Day/Hour

Remove Cleaner

from Pool

Start/Stop Cleaner

Operation

Cancel Programming

Validate Time Setting

Selection

Select Cleaning Surface

• Bottom

• Bottom and Sides

Page 11

English

Display Current

Time/ Set Time

Program Cleaning

Cycles / Set Time

Navigate Day/Hour

Remove Cleaner

from Pool

Start/Stop Cleaner

Operation

Cancel Programming

Validate Time Setting

Selection

Select Cleaning Surface

• Bottom

• Bottom and Sides

• Waterline only

Select Cleaning Level

• Intensive

• High Intensity

Select Pool Shape

• Rectangular

• Freeform

Dirty Filter

Indicator

4.4 The Polaris 9550 Sport/P955 Cleaner Control Unit

4.5 Starting the Cleaner

The default cleaning surface setting for the Polaris

cleaners is Bottom Surface . To change the

current programmed cycle, see Section 5. Programming

the Cleaner.

Select Cleaning Surface (all models):

Use to change cleaning surface setting.

Toggle between: Bottom Only

Bottom and Sides

Waterline (9550 Sport/P955)

Select Cleaning Intensity Level

(9550 Sport/P955 only):

Use to choose cleaning intensity level.

Toggle between: INTENSIVE

HIGH INTENSITY

Select Pool Shape (9550 Sport/P955 only):

Use to choose pool shape.

Toggle between: RECTANGULAR

FREEFORM

Begin Cleaning:

After selecting the cleaning surface and other options as

applicable, press to begin operation.

The screen displays the time remaining for the selected

cycle. For example, 0:44 on the display indicates that

cleaning will be completed in 44 minutes.

NOTE: The control unit automatically switches to standby

power mode after 10 minutes of inactivity and the

display screen turns off. Press any key to exit standby

mode. Cleaner will continue to function in standby

mode if in the middle of a cleaning cycle.

Page 12

English

4.6 Stopping the Cleaner

and Removing from the Pool

The automated Lift System makes removing the cleaner

from the pool simple. The Lift System will move the

cleaner toward the edge of the pool then drive it to the

surface for removal.

1. At the end of the cleaning cycle, or at any time

during a cleaning cycle, press to begin

the automated lift procedure.

Press and hold the Lift System button to turn

cleaner to the left. Cleaner will keep rotating

left. Once the cleaner is oriented towards the

wall of your choice, release the button.

Press and release the Lift System button and the

cleaner will drive up the wall and to the water

line and wait to be retrieved.

The screen displays when the

Lift System is in operation.

NOTE: To stop the lift procedure at any time, press .

2. When the cleaner is within arm's reach, use the

handle to remove from the water (Figures 18,

19). Never lift the cleaner out of the pool by the

oatingcableorswivel.

1

2

Figure 18. Remove Cleaner From Pool with Handle

3

Figure 19. Keep Cleaner Vertical to Drain Water

4.7 Operating the Cleaner with the

Remote Control (9550 Sport/P955 only)

The Polaris 9550 Sport and P955 robotic cleaner comes

with a handheld remote control stored on the cleaner

caddy next to the control unit. The remote control is

factory-synchronized to your cleaner's control unit.

ON/OFF

button

Lift System

button

Figure 20. 9550 Sport/P955 Remote Control

• To turn on the remote control:

Press (see Figure 20) and hold for 3 seconds.

The display shows to indicate the

cleaner is now operating in remote control mode.

• To pilot the cleaner, point the device toward the

cleaner in the water and move directionally as shown

in Figure 21.

Backward

Turn Left

Stop

Turn Right

Forward

Figure 21. Remote Control Directional Commands

Page 13

English

• To remove the cleaner from the pool using the remote

control, press (see Figure 20).

4.8 Synchronizing the Remote Control

Even though the remote control is factory-synchronized

to your cleaner's control unit, it may be necessary to

synchronize again if you need to replace either the

control unit or the remote control.

• To synchronize the remote control to the control unit:

Press and hold for 3 seconds to turn on remote.

Plug the control unit into a power source.

When the display shows the operating time, press

and simultaneously for six (6) seconds.

• The display shows followed by the

normal operating time display to indicate the cleaner

is now synched with the remote and ready to begin

operating in remote control mode.

4.9 Storing the Cleaner

The cleaner must be cleaned regularly using slightly

soapy clean water. Do not use solvents such as

trichlorethylene or its equivalent. Rinse the cleaner

generously using clean water. Do not let your cleaner

dry in direct sunlight near the pool. The cleaner must be

stored on its caddy so that it dries quickly.

1. Place the rear wheels on the caddy side wedges.

2. Place cleaner in vertical position on the caddy

base and clip to hook (Figure 23).

3. Disconnect the cable from the control unit.

Replace the protective cap on the control unit.

4. Starting at the cleaner head. Remove all coils

and tangles from the cable (Figure 22). Lay the

cable in the sun to loosen any tangling memory.

Figure 22. Untangle the Floating cable

5. Loosely coil the power cable starting at the

cleaner and moving toward the connection point

at control unit. Store the cable by wrapping

it around the hook located on the front of the

caddy (Figure 23).

Figure 23. Cleaner Correctly Stored on Caddy

Page 14

English

Section 5. Programming the

Cleaner

(9450 Sport/P945 and 9550 Sport/P955 only)

You can program up to seven preset cleaning cycles to run

thecleaneronaspecicdayandtimewhenyouareaway

from the pool.

NOTE: You cannot change programming or display current

day and time during a cleaning cycle.

5.1 Displaying Current Day and Time

• Press to display current day and time in

24-hour clock format.

Current day and time is displayed for 5 seconds.

5.2 Changing the Clock Day and Time

1. Press and hold for three (3) seconds.

All days of the week ash twice.

2. Press or buttons to cycle through

seven (7) days and display desired day.

3. Press to select.

Current hour setting ashes.

4. Press or buttons to cycle through

24 hours and display desired hour setting.

NOTE: Control unit is set to display time in 24-hour

clock format. Time setting will cycle through 1-24.

5. Press to select.

Current minutes setting ashes.

6. Press or buttons to cycle

through 1-59 minutes and display desired

minutes setting.

7. Press to select.

8. Press to set time and exit the menu.

9. Press to display current day and time

setting and verify the time you set is correct.

5.3 Changing Default Cleaning Times

Use to change cleaning surface setting.

Default cleaning times are:

NOTE: For 9550 Sport and P955, cycle lengths are variable

based on chosen pool shape and cleaning level.

Bottom Only: 1 hour 30 minutes

Bottom and Sides:

2 hours 30 minutes

Waterline (9550 Sport/P955):

0:45, 0:55, or 1:05 minutes,

based on chosen settings

1. Press or buttons to increase or

decrease cleaning time in 30-minute increments.

2. Press to select.

Page 15

English

5.4 Programming Cleaning Cycles

You can program up to seven cleaning cycles.

Program cleaning for either seven consecutive cycles or

the same cycle repeated over several weeks

(e.g., every Wednesday and Saturday for three weeks).

1. Choose pool cleaning settings to program.

All models:

Choose to select either bottom of

pool or bottom plus sides of pool.

9550 Sport/P955:

• Choose to select waterline only in

addition to bottom or bottom plus sides options.

• Choose to select intensive or

high intensity level cleaning.

• Choose to select pool shape.

2. Press to view currrent programmed

cleaning cycles.

Cycle day and time is displayed for three

seconds.

3. When the cleaning cycle you want to change

is displayed, press and hold for 3 to 5

seconds.

Thedaysoftheweekashtwice.

NOTE: If the display flashes all zeros, the time has

not been set (new cleaner). Day and time must be set

before you can program cleaning times, see section

5.2 Changing the Clock Day and Time.

4. Press or buttons to cycle through

7 days of the week.

5. Press to select.

Hour setting ashes twice.

6. Press or buttons to cycle

through 24 hours.

7. Press to select.

Minutes setting ashes zero.

8. Press or buttons to cycle

through four 15- minute increments (00, 15, 30,

or 45).

10. Press to select.

The next day to program ashes.

11. Press to program an additional cleaning

cycle for a different day OR

Press to exit the programming menu

Days of the week are lit indicating programs

stored in the control unit memory for that day.

5.5 Canceling Cleaning Cycles

To Cancel an Individual Program:

1. Press and hold for 3 to 5 seconds.

 Thedaysoftheweekashtwice.

2. Press or buttons to cycle

through seven (7) days.

NOTE: If the day of the week flashes with no time

displayed, there is no program set for that day.

Page 16

English

3. Press and hold for 3 to 5 seconds to

delete programming for the selected day.

Press to exit.

To Cancel All Programs:

1. Press to make sure you have exited

the Programming Menu.

2. Press and hold to delete all

programming in the control unit.

The display will turn off for one (1) second.

When all programs are cancelled, the current

day and time is displayed on the screen with

no days of the week lit.

Section 6. Cleaning and

Maintenance

WARNING

To avoid electric shock and other hazards which

could result in permanent injury or death, disconnect

(unplug) the cleaner from the power source before

performing any cleaning and maintenance.

6.1 Cleaning the Filter Canister

Theltercanistershouldbecleanedattheendofeach

cycle.

1. Make sure the control unit cable is disconnected

fromtheelectricaloutletortheoatingcable

has been disconnected from the control unit.

2. Remove the cleaner from the water and let

the remaining water drain by maintaining the

cleaner in the vertical position.

3. Set the unit on its wheels.

4. Toremovetheltercanisterassemblyfromthe

cleaner, follow steps 5 through 8.

5. Push the cover lock (1) and lift the cover (2)

until it is secured in the vertical position.

(Figure 24).

2

1

Figure 24. Lift Cleaner Cover

6. Removetheltercanisterassemblyfromthe

body (3), as shown in Figure 25.

Page 17

English

3

Figure 25. Remove Filter Canister Assembly

7. Push the quick release button on the canister

assembly(4)andpullopenthelterassembly

(5), as shown in Figure 26.

4

5

Figure 26. Open Filter Canister Assembly

8. Separatetheltercanisterfromthelter

support (6), as shown in Figure 27.

6

Figure 27. Remove Filter Canister

9. Emptyalldebrisfromtheltercanister,then

rinsethecanister,theltersupport,andthe

cleaner under water or using a hose, as shown

in Figure 28.

Figure 28. Wash Filter Canister

7

6.2. Cord Tangling

Tangling can occur more frequently when operating

the cleaner on the automatic timer 7-Day Programmed

Cycle (9450/P945 and 9550/P955). Spread out the

oatingcableoverthepool,ensuringthereareno

kinks or coils in the cable. Do not leave the cleaner

unattended for prolonged periods.

NOTE: For optimal patterning and reduced tangling, the

floating cable should enter the water near the middle

of the pool length. Only place enough cable in the

water to reach the farthest point in the pool.

Page 18

English

IMPORTANT

Cleaner power cable may become tangled if correct

procedure is not followed after each cleaning cycle.

After every cleaning cycle:

1. Unplug power to the cleaner at the control unit.

2. Remove the cleaner from the pool and untangle

all kinks and coils in the power cable starting

at the cleaner head. Lay the cable in the sun to

loosen any tangling memory.

3. Removeltercanisterandrinsewithclean

water. Plug power cord back into control unit

and store cleaner for next use.

6.3 Replacing the Brushes

ThecleaneristtedwithPVCbrushes.Thereare

''wear'' indicators on the brushes (Figure 29). To

maintain cleaner performance at its best you need

to replace the brushes as soon as one of the wear

indicators is reached (even if the blade wear is not

even). It is recommended that you replace the brushes

when the rubber is worn down to the top of the wear

indicator(oreverytwoyears,whichevercomesrst).

Figure 29. Wear Indicators

1. Lift the cleaner to a vertical position so that the

handle is up (Figure 30).

1

Figure 30. Cleaner in Upright Position

2. Separate the edges of the brush and undo the

tabs (Figure 31). Remove the worn brushes.

Page 19

English

2

Figure 31. Undo the Tabs of the Brush

3. To install a new brush, position the new

brush on the roller with the spikes facing

downwards (Figure 32).

3

Figure 32. Install the New Brush

4. Thread each tab into the slot provided and

gently feed it through until the heel comes out

at the other side of the slot (Figure 33).

4

Figure 33. Pull Tabs Through Each Slot

5. Use a pair of scissors to cut the tabs 3/4 inch

from the heel so that they are no higher than

the spikes (Figure 34).

Figure 34. Cut Tabs

6. Repeat this procedure to install the second

brush.

6.4 Replacing the Tires

1. Pull on the inside of the old tire to remove the

tire lip from the wheel (Figure 35).

1

Figure 35. Pull the Old Tire Over the Wheel

2. Remove the old tire (Figure 36).

2

Figure 36. Remove the Old Tire

3. To replace the tire, position the tire on the

wheel making sure to orient the tire so that the

word INSIDE is toward the body of the cleaner

(Figure 37).

Page 20

English

Figure 37. Tire Replacement Orientation

1

I

N

S

I

D

E

Towards

Body

I

N

S

I

D

E

I

N

S

I

D

E

4. Push one side of the tire on to the wheel and

ttheribofthetireinthegrooveofthewheel

(Figure 38).

2

Figure 38. Start on One Side of the Tire

5. Work the tire onto the wheel and verify the

rib of the tire is positioned properly within the

groove of the wheel (Figure 39).

3

Figure 39. Work the Tire On Around the Wheel

6.

Push and position the rib of the inner side of

the tire in the groove of the wheel (

Figure 40).

If needed, turn the wheel gently to help with

installation.

4

Figure 40. Push the Tire into Place on the Wheel

Section 7. Spare Parts

The complete spare parts list and exploded

view is available on the Polaris website at

www.polarispool.com. In Canada, parts list and

exploded view is available at www.polarispool.ca

La page charge ...

Polaris P935 Le manuel du propriétaire

Ce manuel convient également à

Polaris P935 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents