Honeywell IN-Sxx, S1xRx, S2xRx, QA E1, RVG-ST E1 Mode d'emploi

Honeywell

English

Instruction Manual

Pulse generator

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Betriebsanleitung

Impulsgeber

Typ IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Mode d’emploi

Émetteur d’impulsions

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Manual de instrucciones

Emisor de impulsos

Modelos IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Istruzioni d’uso

Trasmettitore d’impulsi

Tipo IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Gebruiksaanwijzing

Impulsgever

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Honeywell

English

Français

Español

Italiano

Nederlands

Deutsch

Instruction Manual

Pulse generator

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Betriebsanleitung

Impulsgeber

Typ IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Mode d’emploi

Émetteur d’impulsions

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Manual de instrucciones

Emisor de impulsos

Modelos IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Istruzioni d’uso

Trasmettitore d’impulsi

Tipo IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Gebruiksaanwijzing

Impulsgever

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Honeywell

English

IN-Sxx

S1xRx

S2xRx

QA E1

RVG-ST E1

Instruction manual

Pulse generator

Type IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1

Honeywell

English

Contents

1. Safety instructions.................................................................................................... 9

1.1 Intended use .............................................................................................................. 10

1.2 Approvals and certifications* ............................................................................ 10

1.3 Copyright and data protection ......................................................................... 11

1.4 Exemption from liability ....................................................................................... 11

1.5 Product liability and guarantee ........................................................................ 12

1.6 Personnel .................................................................................................................... 12

1.7 Intended use and field of application ........................................................... 12

1.8 Legal declarations .................................................................................................. 12

1.9 Recycling and environmental protection .................................................... 12

2. Structure and function ......................................................................................... 13

2.1 Device description .................................................................................................. 13

2.2 Connection configurations ................................................................................ 13

3. Installation and commissioning ....................................................................... 15

4. Storage ....................................................................................................................... 16

5. Cleaning .................................................................................................................... 16

6. Repair ......................................................................................................................... 16

7. Technical data ......................................................................................................... 16

8. Ambient conditions ............................................................................................... 17

9. Approvals*................................................................................................................. 17

10. Annex A – Standards and Norms ................................................................... 18

Honeywell

Information on the documentation

The latest version of the operating instructions is available to download from the

Honeywell website.

Please read the information in this document carefully in order to avoid injury to

the user or damage to the device. Moreover, currently valid national standards,

safety regulations and accident prevention regulations must be adhered to.

Should you have any problems understanding the contents of this document,

please contact your local Honeywell branch for support. Honeywell cannot

accept any responsibility for damage to property or personal injuries which are a

result of the information in this document not having been understood properly.

This document helps you to set up the operating conditions in such a way that

the safe and efficient use of the device is assured. In addition, this document also

specifies points and safety measures which must be particularly observed and

which are indicated using the following symbols:



WARNING or CAUTION

This symbol warns of dangerous situations. Failure to follow the

instructions could result in danger to people and the

environment or the meter could suffer damage.



INFORMATION or NOTE

Accurate measurement cannot be ensured if information or

notes with this symbol are ignored.

Honeywell

English

1. Safety instructions



WARNING!

Danger of electrostatic discharge – only use a damp cloth to clean.



WARNING!

If there is danger that the device can be damaged from falling

(pointed, sharp-edged or heavy) objects, the operator must protect

the device.



WARNING!

Exposure to danger which can result from a chemical reaction

between parts of the meter and chemical substances in the vicinity

must be discussed with the manufacturer and the cause must be

eliminated.



WARNING!

The gas meter on/in which the pulse generator is installed must be

integrated into the equipotential bond, e.g. by connecting it to the

grounded pipeline.



INFORMATION!

Compliance with the specified operating and ambient conditions

as indicated on the type label and the gas meter type label is

absolutely essential for the safe operation of the pulse generator.

Honeywell

1.1 Intended use



INFORMATION!

The

manufacturer shall not be liable for damage caused by

improper or inappropriate use.

1.2 Approvals and certifications*

CE marking / EU declaration of conformity

The manufacturer certifies conformity with the EU

declaration of conformity and by attaching the CE marking.

The pulse generator meets the statutory requirements of

the relevant EU guidelines.

Comprehensive information on the applicable EU

guidelines and standards, as well as recognized

certifications, is contained in the EU

declaration of

conformity.

The EU declaration of conformity is included in the delivery

and is also available to download at www.docuthek.com.

 See Chapter 9 for more approvals and Directives.

Approvals and Annex A – Standards and Norms

ATEX/IECEx



DANGER!

The pulse generator is suitable for use in Zone 1 hazardous

areas and is approved with the following certification:

 II 2G Ex ia IIC T4 Gb



II 2G Ex ib IIC T4 Gb

IECEx TUR 16.0032X (IECEx)

TÜV 16 ATEX 7729 X (ATEX)

TÜV Rheinland Industrieservice GmbH

Am Grauen Stein | 51105 Köln | Germany

TÜV Rheinland Industrieservice GmbH

Am Grauen Stein | 51105 Köln | Germany

* The marking on the device shall be applicable.

Honeywell

English

1.3 Copyright and data protection

This document has been created with the greatest possible care. No liability

is assumed for the accuracy, completeness or currency of the contents.

The contents and works produced in this document are subject to copyright.

Contributions by third parties are identified as such. The reproduction,

processing, distribution and any form of use beyond that which is permitted

by copyright require the written authorization of the respective author or the

manufacturer. The manufacturer strives to always respect the copyright of

others or to use his own or licence-free works.

We would like to point out that data transfer via the Internet (e.g. through e-

mail communication) can be subject to breaches in security. It is not

possible to provide complete protection against access by third parties.

1.4 Exemption from liability

The manufacturer shall not be liable for damage of any type caused by the

use of this product, including but not restricted to, direct, indirect or

incidental damage and its consequences.

This exemption from liability does not apply if the manufacturer has acted

intentionally or with gross negligence. In the event that any applicable law

does not allow such restrictions on implied warranties for defects, or the

exclusion or limitation of certain payments for damages, and should such

law apply to you, the above-mentioned exemption from liability, exclusions

or limitations may not apply to you in part or in whole.

For every product purchased, the warranty is valid in accordance with the

corresponding product documentation as well as the conditions of sale and

delivery of the manufacturer.

The manufacturer reserves the right to amend without prior notice the

contents of the documents, including this exemption from liability, in any

form and at any point in time, and for any reason, and shall in no way be liable

for any possible consequences of such amendments.

Honeywell

1.5 Product liability and guarantee

The responsibility as to whether the device is suitable for the intended use is

that of the operator. The manufacturer cannot accept any liability for the

consequences of misuse by the operator. Improper installation or operation

of the devices (systems) render the warranty void. Furthermore, the relevant

“General Terms and Conditions” which form the basis of the purchase

contract also apply.

1.6 Personnel

This manual is aimed at staff who have adequate specialist and technical

knowledge (in Germany, for instance, in accordance with DVGW Codes of

Practice 492 and 495 or comparable technical regulations) on the basis of

their training and experience in the sector of energy and gas distribution.

1.7 Intended use and field of application

This product is intended to be used for the installation on/in gas meters

from Elster/Honeywell

This product is not intended to be used for the installation on/in gas meters

from other manufacturers.

1.8 Legal declarations

The metrological conformity assessment is based on the regulations of the

country concerned, where the device will be used.

1.9 Recycling and environmental protection

Honeywell has designed the transport packaging of the device to be

environmentally friendly. Packaging materials are always selected

consistently with a view to recycling. The cardboard items used constitute

secondary raw materials for the paperboard and paper industry. The

Instapak® foam packaging items can be recycled and reused in most

countries. Plastic sheeting and strips/bands are also made of recyclable

plastic. At Honeywell, subsequent recycling and disposal are already

elements of the product development process. When selecting the materials,

we allow for reusability of the materials, suitability of materials and

subassemblies for dismantling and separation, and the risks of

environmental pollution and health risks when recycling and dumping on

landfill sites.

Honeywell

English

2. Structure and function

The products IN-Sxx / S1xRx / S2xRx / QA E1 / RVG-ST E1 are low-frequency

pulse generators for turbine and rotary gas meters from Elster/Honeywell.

The versions IN-Sxx can be attached to the index from the outside. The

versions S1xRx / S2xRx / QA E1 / RVG-ST E1 are integrated in the index.

2.1 Device description

The pulse generators consist of one series connection per channel

comprising a reed switch and a resistor. The reed switch is driven by a

magnet which is located on the inside of the gas meter index. The rotation of

the magnet usually corresponds to the rotation of the last digit roller of the

mechanical index.

When the magnet triggers the reed switch, the attached electrical circuit is

closed. A closure corresponds to one pulse.

2.2 Connection configurations

Type Version Terminals

IN-S10

IN-S10K

IN-S10V

6-core cable

E1 = brown (+) / white (-)

E2 = green (+) / yellow (-)

PCM = grey (+) / pink (-)

IN-S10A 4-core cable E1 = brown (+) / white (-)

PCM = green (+) / yellow (-)

IN-S11

S1xR3

S2xR3

RVG-ST 2xE1

6-pin plug

E1 = 1(+) / 2(-)

E2 = 5(+) / 6(-)

PCM = 3(+) / 4(-)

IN-S11F 6-pin plug

BF = 4(+) / 6(-)

BF = 3(+) / 5(-)

PCM = 1(+) / 2(-)

Honeywell

S1xR

S2xR 6-pin plug

E1 = 1(+) / 2(-)

IN-S12

Two 6-pin plugs

Plug 1

E1 = 1(+) / 2(-)

Plug 2

E2 = 1(+) / 2(-)

PCM = 3(+) / 4(-)

IN-S12F

Two 6-pin plugs

Plug 1

BF = 4(+) / 6(-)

PCM = 1(+) / 2(-)

Plug 2

BF = 3(+) / 5(-)

IN-S15

IN-S16 6-pin plug

E1 = 1(+) / 4(-)

E2 = 2(+) / 5(-)

PCM = 3(+) / 6 (-)

QA E1 3-pin plug

E1 = 1(+) / 4(-)

Honeywell

English

IN-S22

Two 3-pin plugs

Plug 1

E1 = pin A(+) + B(-)

E2 = pin C(+) + B(-)

Plug 2

E1 = pin A(+) + B(-)

E2 = pin C(+) + B(-)

Table 1 | Terminal assignment

3. Installation and commissioning

 The pulse generator versions IN-Sxx are inserted sideways into the

mounting of the index until they click into place (see Fig. 1).

 The pulse generators S1xRx / S2xRx / QA E1 / RVG-ST E1 are supplied

ready for operation together with the gas meters.

 The cables are to be connected as per Table 1, Terminal assignment.

 For connecting the devices, use a screened cable pursuant to

IEC EN 60079-14.



WARNING!

If the pulse generators are used in hazardous areas, they have to be

connected to intrinsically safe circuits.

Safety barriers must be equipped for ignition protection rating

Ex ib IIC or Ex ia IIC.

Fig. 1 | Installation of IN-Sxx

Honeywell

4. Storage

 Store the device in a dry and dust-free location.

 Avoid constant direct sunlight.

 Store the device in its original packaging.

 Storage temperature: -40 to +70°C / -40 to +158°F.

5. Cleaning



WARNING!

Danger of electrostatic discharge – only use a damp cloth to clean.



DANGER!

 There is a risk of explosion if the plastic cover of the index is

cleaned with a dry cloth.

 It is forbidden to use aggressive chemical cleaning agents or

solvents for cleaning.

6. Repair



INFORMATION!

Repairs may be carried out only by authorized workshops.

7. Technical data

Ui

≤ 24 V

Ii

≤ 25 mA

Pi

≤ 0.25 W

Ci

= 0 F

Li

= 0 H

Table 2 | Technical data

Honeywell

English

8. Ambient conditions

Ambient temperature

-40°C to +70°C

Storage temperature

-40°C to +70°C

IP protection class

IP67

Humidity 0 to 80% RH

Max. height above sea level

2000 m

Outdoor installation

Yes

Mechanical environments

M1

Installation category according to

CAN/CSA

1

Environment conditions according to

CAN/CSA

Pollution degree 2

Table 3 | Ambient conditions

9. Approvals*

Approval:

Approval number:

Approval body:

CSA

CSA 17CA70097478

CSA Group | 178 Rexdale Boulevard

Toronto, ON M9W 1R3

ATEX



II 2G Ex ia IIC T4 Gb

 II 2G Ex ib IIC T4 Gb

TÜV 16 ATEX 7729 X

TÜV Rheinland Industrieservice GmbH

Am Grauen Stein | 51105 Köln | Germany

IECEx Ex ia IIC T4 Gb

Ex ib IIC T4 Gb

IECEx TUR 16.0032X

TÜV Rheinland Industrieservice GmbH

Am Grauen Stein | 51105 Köln | Germany

Table 4 | Approvals

ATEX/IECEx legend:

 Marking of explosion protection

II Equipment group: industrial (mining excluded)

2 Equipment category 2 (Zone 1)

G Potentially explosive gas atmospheres

ia/ib Type of ignition protection: intrinsically safe

IIC Explosion group for gases

T4 Temperature class

Gb Equipment protection level

* The marking on the device shall be applicable.

Honeywell

10. Annex A – Standards and Norms

The pulse generators meet the following norms and standards or the

relevant chapters within them*.

2014/32/EU – Annex IV (MI-001),

Annex VII (MI-005)

Measuring Instruments Directive (MID)

DIN EN 12480:2015

Gas meters – Rotary displacement gas meters

DIN EN 12261:2002 + A1:2006

Gas meters – Turbine gas meters

DIN EN 60079-0:2012 + A11:2013

IEC 60079-0:2011

CAN/CSA-C22.2 NO. 60079-0:15

Explosive atmospheres – Part 0: Equipment –

General requirements

DIN EN 60079-11:2012

IEC 60079-11:2011

CAN/CSA-C22.2 NO. 60079-11:14

Explosive atmospheres

Part 11: Equipment protection by intrinsic safety

“i”

CAN/CSA-C22.2 NO. 0-10

General requirements – Canadian electrical code,

part II

CAN/CSA-C22.2 NO. 61010-1-12

Safety requirements for electrical

equipment for measurement, control and

laboratory use – Part 1: General requirements –

Third edition

* Standards valid at the time of the operating instructions going to press.

Honeywell

English

La page charge ...

Honeywell IN-Sxx, S1xRx, S2xRx, QA E1, RVG-ST E1 Mode d'emploi

Honeywell IN-Sxx, S1xRx, S2xRx, QA E1, RVG-ST E1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents