For VM342-2 only
If you are viewing baby unit , the ON/OFF LED light of baby unit turns on. As baby
unit is not being viewed, its ON/OFF LED light flashes.
Note
• If you power on only one baby unit, you may see the parent unit displaying and then
No link to CAM # (# represents the baby unit number), and the LINK LED light flashing.
Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.
Status check - Two baby units
Mount the baby unit (optional)
Align the wall mount bracket and
screws with the holes in the wall as
shown. Tighten the screw in the middle
hole first, so that the wall mount
bracket position is fixed. You can
tighten the other screw in the top hole.
OR
Select Patrol as your monitoring mode to alternately view the image from baby units
and every 10 seconds.
Change different views - Patrol
Select Split as your monitoring mode to view the images from both
baby units at once.
Change different views - Split
In Single CAM or Patrol mode, press VIEW to switch between the image of baby
units and .
Change different views - Single CAM
Overview - Parent unit
Dim mode
With dim mode preset to
on, your parent unit display
will dim to conserve energy
after 10 minutes of inactivity,
in which there is neither key
pressed nor alert received
from the baby unit.
10 min inactivity
Press any buttons
Note
• If you do not want LCD to dim automatically, turn off the Dim Mode.
Dim Mode
On
LCD
Brightness
Dim Mode
Night vision
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colors and backgrounds, the video quality
may vary. Adjust the baby unit’s angle or
place the baby unit at a higher level to
prevent glare and blurry display.
Place the wall mount bracket on a wall and
then use a pencil to mark the top and the
bottom holes as shown. Remove the wall
mount bracket and drill two holes in the wall
(7/32 inch drill bit).
Note
• Check for reception strength and camera angle
before drilling the holes.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Insert the screws into the holes and tighten
the screws until only 1/4 inch of the screws
are exposed.
You can maximize your baby unit’s viewing angles by
tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in
anticlockwise direction. This will loosen the joint of
the wall mount bracket. Tilt your baby unit up or
down to adjust to your preferred angle. Then, rotate
the knob in clockwise direction to tighten the joint
and secure the angle.
Overview - Baby unit
Threaded socket
Power jack
Speaker
Temperature
sensor
+ VOLUME -
ON/OFF
switch
Install the lens (optional)
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
The wide-angle lens (VM101) provided
allows you to view more of your baby’s
room from the parent unit screen. Install
the wide-angle lens onto the baby unit
camera as shown below.
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
W
I
D
E
A
N
G
L
E
L
E
N
S
Remove the lens
Notes
• When the lens is not in use, cover both sides of the lens with the lens covers provided to avoid
scratches.
• You can purchase and install an extra new wide-angle lens (VM101) onto your baby unit if necessary.
Light sensor
Camera
Microphone
ON/OFF LED light
Infrared LEDs
Play/Stop
Skip
Place the baby unit on the wall mount
bracket. Tighten the screw into the
threaded socket at the bottom to
secure the baby unit.
Place the baby unit on the wall mount
bracket. Tighten the screw into the threaded
socket at the bottom to secure the baby
unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Note
• The types of screws and anchors you need
depend on the composition of the wall.
Sound sensitivity and sound activation
Sound-activated Screen
On
O
Sensitivity
Low
Medium
High
Highest
Sound activated screenAdjust sound detection sensitivity
When sound activation is on, the parent
unit screen stays off to save power
when the baby unit detects no sound.
Once the baby unit detects sounds
that are louder than the chosen sound
sensitivity level, the parent unit screen turns on automatically. It will
then turn off again after 50 seconds of no sound detection.
With sound sensitivity setting,
you can choose to hear sounds
from the baby unit all the time,
or to hear sounds that exceed a
certain level.
Parent unit
setting
What
happens... You may
experience... What you could do...
Speaker
volume:
LOW
Sensitivity:
Highest
[Default]
Hear all
sounds all
the time,
including
background
sounds.
Difficulty in
hearing your
baby’s soft
sounds if the
background
sounds are
louder.
• Increase parent unit’s
speaker volume, and
lower sound sensitivity.
• If you are using a
white noise machine
or sound machine, set
its volume to low, or
relocate it to minimize
background sounds.
Speaker
volume:
MAX
Sensitivity:
Low /
Medium
Only hear
sounds that
exceed the
selected
sound
sensitivity
level.
No sound; or
sounds that
cut in and
out at times
as the baby
unit may not
detect extra
soft sounds.
Increase the sound
sensitivity, and adjust the
volume level if necessary.
For details, please see Adjust the sound sensitivity of the baby
unit in the User’s manual.
Stand
Power
jack
Speaker
Antenna
On/off
TALK
Zoom
Microphone
LED lights
Arrow keys
MENU
/
SELECT
+
VOL
-
VIEW / LCD ON/OFF
PATROL
SPLIT
10s
Press VIEW