GoCom 2020G9 Manuel utilisateur

Marque: GoCom

Modèle: 2020G9

Catégorie: Radios bidirectionnelles

Taper: Manuel utilisateur

2. You can also press button to check for activity on the

current channel before you talk.

3. Release the button to exit monitor mode.

User can use this function to switch between two-way and

weather mode by press and hold for 3 seconds.

335100418 _RevA

OPERATING INSTRUCTION

Walkie-Talkie

1 2 3

654 7

1098 11

13 14 1512

Note:

Please read the operating instructions carefully

before using the device.

GETTING STARTED

Insert 3 AA NiMH

batteries.

Close the battery

cover.

Radio Battery Meter

KEY FUNCTIONS

Installing the Three AA NiMH Rechargeable Battery

1. Take the belt clip off.

2. Unlock two screws counterclockwise and open the cover ot

install the three AA NiMH battery according to orientation shown

in battery compartment.

3. Close the battery and tighten the two screws clockwise.

4. Tighten the screws clockwise to close the battery cover firmly.

Battery full bars indicates battery high .When battery meter

shows 1 bar, device is on low battery mode and will indicate low

battery alert in the forms of alert tone and blinking bar display.

Using the Micro-USB Charger

The micro-USB charger is a handy port that allows you to

conveniently charge your NiMH battery. Use certified adaptor(5V,

≥1A). Do not attempt to charge alkaline batteries.

1. Make sure your radio is turned OFF.

2. Plug the micro-USB cable into the micro-USB charging port on

DISPLAY SCREEN GUIDE

Numbers of Channel

Call Tone

Numbers for Codes

Dual Watch

Scan

VOX

Batt ery Meter

Status

(Transmit/Receive)

Volume Mut e

Lock

Weather Alert

Remove the

battery cover.

screws

When you press PTT buttons for more than 60 seconds, radio will stop

transmitting. This is to prevent accidental transmission.

To communicate, all radios in your group must be set to the same

channel and sub code.

1. To talk, press and hold the PTT button. When transmitting, the

icon is shown. Release the PTT button when you are finished

talking. Do not use the radios closer than five feet apart.

2. When receiving, the icon is shown.

Monitor Button

PTT Timeout Timer

1. Press and hold button for 3 seconds to enter monitor mode and

listen for weak signals on the current channel.

Mode But ton

RECEIVING AND TRANSMITTING

FEATURES

2. Press or button to change t he channel number.

Setting the Channel 2. Press or button to select code number. Press the

PTT button to exit menu .

Setting and Transmitting Call Tones

1. Press button until call tone 'CA' appears. The current call

tone setting flash.

1. Press the button until the code number starts to flash.

Press the PTT button to exit menu

Press the

PTT button to exit menu

Setting the Sub Codes

1. Press the button until the channel number starts to flash.

2. Press or button to change and listen to the call tone.

Voice Operated Transmission (VOX)

L3=High Sensitivity

L2=Medium Sensitivity

L1=Low Sensitivity

L0=Turn Off VOX function

exit menu. The screen will alternate between Home Channel

and Dual Watch Channel.To end Dual Watch mode, re-enter

Dual Watch menu to select the OFF setting. If you set the

same channel and code as current channel, Dual Watch does

not work.

2. Press or to select channels.

Dual Channel Monitor

Press the PTT button to

With this feature enabled, you can scan current channel and

another channel alternately.

1. Press button until '2CH' appears on the display. The current

setting (OF, 1-22) will flash.

Press the

PTT button to exit menu.

1. To activate VOX, press button until 'VOX' appears on the

display. The current setting (0, 1-3) will flash.

2. Press or button to select the sensitivity level.

Press and hold the button while turning the radio ON to switch the

keypad tone ON/OFF.

Press and hold the button while turning the radio ON to turn the

Roger Beep ON. Repeat the step to turn Roger Beep OFF.

2. To unlock t he radio, press and hold but t on unt il key lock

indicator icon on display disappear.

Keypad Tones

Scanning Channels

To Start Scanning:

1. Briefly press the button to start scanning. SCAN icon will

appear in the display. The device will stop scrolling and

receiving when matched channel and sub codes detected.

2. After the end of transmission, press the PTT button within 5

seconds to respond. The device will resume scanning after end

of any received activity.

3. If you press PTT button when the device is scrolling, the

transmission will be on the 'home channel'.

4. Press button to exit scanning feature.

Roger Tone

Keypad Lock

1. To lock t he radio, press and hold but t on unt il t he key lock

indicator icon on display appear.

Your radio receives weather frequencies:

Entering Weather Mode

press and hold button for 3 seconds to enter weather mode.

Setting the Weather Channel

3. Press the PTT button to set and exit menu.

2. Press or button to select the appropriate channel.

1. In weather mode, press the button until weather channel

number flashes.

WEATHER RECEIVE

Setting the Weather Alert

Your radio can be set to respond to NOAA Weather Radio

emergency messages.

2. Press or button to select On/Off.

1. In weather mode press the button twice until icon

displays.

3. Press the PTT button or button to exit the weather menu set up.

WEATHER CHANNELS & FREQUENCIES

Weather

Channel (MHz)

Frequency Weather

Channel

Frequency

(MHz)

WX1 162.550 WX7 162.525

WX2 162.400 WX8 161.650

WX3 162.475 WX9 161.775

WX4 162.425 WX10 161.750

WX5 162.450 WX11 162.000

WX6 162.500

SAFETY & GENERAL INFORMATION

FCC Warning

Any Changes or modifications not expressly approved by

the party responsible for compliance could void the user's

authority to operate the equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

Safety Information for Radios

Your wireless handheld portable transceiver contains a low

power transmitter. When the talk button is pushed, it sends out

radio frequency (RF) signals. The device is authorized to

operate at a duty factor not to exceed 50%. In August 1996,

the Federal Communications Commissions (FCC) adopted RF

exposure guidelines with safety levels for handheld wireless

devices.

Important

FCC RF Exposure Requirements: For body-worn operation,

this radio has been tested and meets the FCC RF exposure

guidelines when used with accessories supplied or designated

for this product. Use of other accessories may not ensure

compliance with FCC RF exposure guidelines. Use only the

supplied antenna. Unauthorized antennas, modifications or

attachments could damage the transmitter and may violate

FCC regulations.

Normal Position

Hold the transmitter approximately 25 mm from your face and

speak in a normal voice, with the antenna pointed up and

away.

ISEDC Warning

This product meets the applicable Industry Canada technical

specifications. / Le présent matériel est conforme aux

specifications techniques applicables d’Industrie Canada.

This device complies with ISEDC license-exempt RSS

standard (s). Operation is subject to the following two

conditions:(1) this device may not cause interference, and (2)

this device must accept any interference, including interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISEDC

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

ISEDC Radiation Exposure Statement

For body worn operation, this model device has been tested and

meets the FCC/ISED RF exposure guidelines when used with

an accessory designated for this product or when used with an

accessory that Contains no metal and that positions of the face

up minimum distance is 25 mm.

Any Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority

to operate the equipment.

Pour le corps, ce modèle d’appareil a été testé et adapté à la RF

renforcée Lignes directrices relatives à l’exposition lorsqu’elles

sont utilisées avec un accessoire pour ce produit ou lorsqu’elles

sont utilisées avec celui-ci Un acces-soire ne contenant pas de

métal et dont la distance minimale de la face est de 25 mm.

Tout changement ou modiÿcation non expressément approuvé

par la partie responsable de la conformité l'équipement.

Your wireless handheld portable transceiver contains a low

power transmitter. When the talk button is pushed, it sends out

radio frequency (RF) signals. The device is authorized to

operate at a duty factor not to exceed 50%.

Votre émetteur-récepteur portable sans fil contient un émetteur

de faible puissance. Lorsque le bouton de conversation est

enfoncé, il envoie des signaux de radiofréquence (RF).

L'appareil est autorisé à fonctionner avec un facteur d'utilisation

ne dépassant pas 50%.

Lock / Menu

Monitor / Scan

Microphone

Speaker

Micro-USB

Charging Port /

Accessory Port

Push-to-Talk

Power On / Off

Call Tone

Lamp On / Off

Weather Switch

Lamp

SOS

SOS Lamp

Note:

- Remove the battery from radio for storage purposes. Batteries

may corrode over time and cause permanent damage to your

devices.

- Do not mix and use old/new/alkaline/NiMH batteries.

- Charge the supplied NiMH batteries once every 3 months when

not in use.

Turning your Radio On and Off

2. The display screen then shows the current channel, code and

all features that are enabled.

1. Press to increase the volume. Press to decrease the volume.

2. When the volume reached level 0 the mute icon appears

permanently on screen.

1. Press and hold on the button to turn your radio ON/OFF.

Setting the Volume

your radio. Connect the other end of the micro- USB charger

to wall power outlet.

3. The battery meter on LCD will move to indicate the battery is

charging.

3. Repeat the step to unlock the device.

Repeat the step to disable the weather alert.

Notes:

Automatic Power Saving

Press the button to turn ON/OFF the lamp.

LED Lamp

This feature is enabled by default to enhance battery life.

Emergency SOS Mode

User can use this feature to emit SOS signal. To enter emergency

SOS mode:

1. Press and hold the SOS button for 3 seconds. The RED LED

light will be activated.

2. Press the button again to deactivate.

Water Activated LED

Once the devices are dropped into water, white LED will be

activated automatically to ease user to locate the devices in dark

environment. After retrieve the devices, press any button to

deactivate except button. button will overwrite and

activate LAMP feature.

CH Frequency

(MHz)

Max

Power

Out put (MHz)

Frequency Max

Power

Out put

1 462.5625 2W 12 467.6625 0.5W

2 462.5875 2W 13 467.6875 0.5W

3 462.6125 2W 14 467.7125 0.5W

4 462.6375 2W 15 462.5500 2W

5 462.6625 2W 16 462.5750 2W

6 462.6875 2W 17 462.6000 2W

7 462.7125 2W 18 462.6250 2W

8 467.5625 0.5W 19 462.6500 2W

9 467.5875 0.5W 20 462.6750 2W

10 467.6125 0.5W 21 462.7000 2W

11 467.6375 0.5W 22 462.7250 2W

Set t ing High Low Power

1. Press button unt il 'Pr' appears on the display.

2. Press or button to select HI or LO. (HI- High Power, LO-

Low Power)

3. Press t he PTT button to exit menu.

Channels and Frequences

If the device stops on an unintended/undesired transmission,

press or button to resume scan OR temporarily remove

that channel from the scan list by pressing and holding or

for 3 seconds. Press to exit and re-enter scan mode

to restore removed channels to the scan list.

GoCom 2020G9 Manuel utilisateur

Marque: GoCom

Modèle: 2020G9

Catégorie: Radios bidirectionnelles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: GoCom 2020G9 User manual

GoCom 2020G9 Manuel utilisateur

GoCom 2020G9 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents