Vanguard VG286-5 Manuel utilisateur

VG286-5
Vanguard
Marque
Vanguard
Modèle
VG286-5
Taper
Manuel utilisateur
Fitting Instructions - Read instructions carefully before fitting and follow them for correct use
IN8102 ULTI Bars - X5
This FITTING INSTRUCTION is the property of VAN GUARD ACCESSORIES LTD. and must not be used for
manufacturing purposes, copied nor communicated in any way to third parties without written
permission from VAN GUARD ACCESSORIES LTD.
IN8102_G (CN:00114)
Van Guard Accessories Ltd
Fair Oak Close, Exeter Airport Business Park,
Exeter, Devon, EX5 2UL
www.van-guard.co.uk
IN8102 - PAGE 1 OF 7
!
TOOLS REQUIRED
i
MAX
??
MAX
??
80KG
MAX
MA6021 X20
FX4011 X20
(M8)
FX4014 X20
(RUBBER)
FX4016 X20
(M6)
FX4013 X20
(M6)
FX4020 X20
(M8)
FX4024 X20
(M8X40)
FX4025 X20
(M6)
FX4026 X20
(M6X20)
FX4042 X20
(M6)
MA6065 X10 ME0062 X1 ME0063 X1 ME0064 X6 ME0065 X1 ME0066 X1 ME0203 X10 ME0759 X10 AS3192 X5
10MM X 1
13MM X 2
GB. Tested to 80kg per bar. Maximum load is in accordance with the vehicle manufacturer’s load bearing
capacity (refer to the vehicle handbook). Do not exceed this limit.
FR. Testé à 80 kg par barre. La charge maximale doit être conforme à la capacité de charge du constructeur de
véhicule (veuillez- vous référer au livret du véhicule). Ne dépassez pas cette limite.
DE. Geprüft bis 80kg pro bar. Die Maximallast steht im Einklang mit der angegebenen Ladekapazität des Fahrzeu-
gherstellers (diese finden Sie im Fahrzeughandbuch). Die Maximallast darf nicht überschritten werden.
DK. Testet til 80 kg pr. bar. Maksimal lasteevne afhænger af varevognproducents angivelser i varevognens
håndbog. Overskrid ikke denne grænse.
IN8102 - PAGE 2 OF 7
Vehicle:
Nissan NV400: 2010-2021
Nissan Interstar: 2022 on
Renault Master: 2010 on
Vauxhall Movano: 2010-2021
Wheel Base: LWB (L3)
Roof Height: Medium (H2)
Rear Doors: Twin
VG286-5
18.5KG
=
GB: THIS PRODUCT SUITS THE FOLLOWING VEHICLES FR: CE PRODUIT CONVIENT AUX VÉHICULES SUIVANTS DE: DIESES PRODUKT IST FÜR DIE FOLGENDEN FAHRZEUGTYPEN GEEIGNET DK: DETTE PRODUKT PASSER FØLGENDE KØRETØJER
Vehicle:
Nissan NV400: 2010-2021
Nissan Interstar: 2022 on
Renault Master: 2010 on
Vauxhall Movano: 2010-2021
Wheel Base: XLWB (L4)
Roof Height: Medium (H2)
Rear Doors: Twin
VG286-5
18.5KG
=
4332mm
6848mm
2500mm
FWD 4332mm / RWD 3682mm
6198mm
2500mm
IN8102 - PAGE 3 OF 7
1ME0064ME0062
ME0066ME0065
ME0063
ME0759
Remove roof plugs to reveal the vehicles fixing points. Stick rubber pads to all roof brackets.
23
ME0759 &
ME0066
ME0759 &
ME0064
ME0759 &
ME0062
ME0759 &
ME0065
ME0759 &
ME0064
ME0759 &
ME0063
IN8102 - PAGE 4 OF 7
Loosely secure the middle inner fixing brackets to the inside of the vehicle by inserting the M6 1/4 turn nut inserts (FX4025) into the positions shown in FIG.1. Then place the
middle inner bracket into place and loosely bolt into the M6 1/4 turn inserts using M6x20 hex bolts and M6 washers. Please note the cable trim (shown in FIG.2) may have to be
removed. This trim can be refitted after the inner bracket has been secured.
Loosely secure the rear inner fixing brackets to the inside of the vehicle by inserting the M6 1/4 turn nut inserts (FX4025) into the positions shown below. Then place the rear
inner bracket in position and loosely bolt into the M6 1/4 turn inserts using M6x20 hex bolts and M6 washers.
5
LEFT / ME0066
RIGHT / ME0065
LEFT (ME0066) RIGHT (ME0065)
FIG.1 FIG.2
MIDDLE / ME0064
MIDDLE / ME0064
MIDDLE (ME0064)
TRIM MAY NEED REMOVING BEFORE FITTING. THIS
CAN BE RE-FITTED AFTWARDS.
M6 1/4 TURN NUT INSERT LOCATIONS M6 1/4 TURN NUT INSERT LOCATIONS
4
Loosely secure the front inner fixing brackets to the inside of the vehicle. Where a sliding door is present remove the 2X star drive screws, place front inner bracket in position and
refit star drive screws as shown in fig.1. (Do not remove door rail bracket)
Where a sliding door is not present insert the M6 1/4 turn nut inserts into the positions shown in fig.2. Then place the front inner bracket in position and loosely bolt into the M6 1/4 turn nut
inserts using M6x20 hex bolts and M6 washers.
6
7 8
LEFT / ME0062
RIGHT / ME0063
LEFT (ME0062) RIGHT (ME0063)
DOOR RAIL BRACKETSTAR DRIVE FIXING (X2)
1 2
M6 1/4 TURN NUT INSERT LOCATIONS
Place the roof brackets onto the roof and bolt down through the fixing points and
through the inner fixing brackets using M8X40 hex bolts, M8 washers & rubber
washers.
Place the roof bars onto the roof brackets and loosely secure using M6X16 coach
bolts & M6 flange nuts.
IN8102 - PAGE 5 OF 7
Secure the roof brackets to the inner fixing brackets using M8 flange nuts and
tighten to 12Nm.
11 12
Adjust the roof bars to ensure that they are evenly spaced on the vehicle. Tighten the roof bar fixings to 8Nm.
Tighten the M6 fixings on all inner fixing brackets to 8Nm.
9
==8Nm
10
12Nm 8Nm
IN8102 - PAGE 6 OF 7
1. Inspecter régulièrement toutes les fixations et les pièces. Les pièces endommagées ou
usées doivent être immédiatement retiré du véhicule et remplacé.
2. Prendre garde lors du chargement et du déchargement de marchandises vers et hors
des véhicules toit.
3. Van Guard Accessoires Ltd et/ ou ses distributeurs n'accepte pas de responsabilité pour:
- Les produits qui ont été ajustés de manière incorrecte.
- Les produits qui ont été montés sur le véhicule incorrect.
- Les produits qui ont été modifiés de quelque façon ou sont utilisés à toutes fins
qu'ils sont involontaires.
4. Il est important que l'utilisateur final reçoit ce document et que les instructions soient
conservés pour une utilisation futur.
1. Prüfen Sie regelmäßig alle Befestigungen und Teile. Alle verschlissenen oder
beschädigten Teile sollten sofort aus dem Fahrzeug ausgebaut und erneuert.
2. Vorsicht beim Be- und Entladen von Gütern auf und abseits der Fahrzeuge.
3. Van Guard Accessories LTD und/ oder seinen Händlern keine Haftung für:
- Sämtliche Produkte, die falsch montiert worden.
- Alle Produkte, die auf die falsche Fahrzeug.
- Alle Produkte, die nicht in irgendeiner Weise verändert oder verwendet für
jeden Zweck, sie sind unbeabsichtigt.
4. Es ist wichtig, dass der Endbenutzer erhält dieses Dokument und die Anweisungen für
eine zukünftige Verwendung aufbewahrt werden.
1. Undersøg med jævne mellemrum alle løsdele og fæstninger. Beskadigede eller slidte
dele bør straks fjernes fra køretøjet og repareres eller erstattet.
2. Vær meget opmærksom ved lastning og losning af varer fra varevognens tag.
3. VanGuard Accessories Ltd og/eller deres distributører accepterer ikke ansvar for:
- Produkter der ikke er monteret korrekt som angivet i monteringsvejledning.
- Produkter der er blevet monteret på et køretøj, de ikke er beregnede til.
- Produkter der er blevet modificerede på nogen måde eller bliver brugt på en
måde, hvortil de ikke er beregnede.
4. Det er vigtigt, at dette dokument overdrages til slutbruger af produktet og at vejledning
er gemt til senere brug.
1. Regularly inspect all fixings and parts. Any damaged or worn parts should be immedi-
ately removed from the vehicle and replaced.
2. Take care when loading and unloading goods on to and off the vehicles roof.
3. Van Guard Accessories LTD and/ or its distributors do not accept liability for:
- Any products that have been fitted incorrectly.
- Any products which have been fitted to the incorrect vehicle.
- Any products that have been modified in any way or are being used for any
purpose that they are unintended for.
4. It is important that the end user receives this document and that instructions are
retained for future use.
GB
FR
DE
DK
IN8102 - PAGE 7 OF 7
13
1.
2.
3.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Vanguard VG286-5 Manuel utilisateur

VG286-5
Vanguard
Marque
Vanguard
Modèle
VG286-5
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents