DeWalt DCS781 Manuel utilisateur

Catégorie
Scies à onglet
Taper
Manuel utilisateur
DCS781
12" (305 mm) 60V Double Bevel Sliding Miter Saw
Scie à onglets à glissière double biseau 305mm (12po) 60V
Sierra de Inglete Deslizable de Doble Bisel de 305mm (12") 60V
If you have questions or comments, contactus.
Pour toute question ou tout commentaire, nouscontacter.
Si tiene dudas o comentarios,contáctenos.
1‑800‑4‑DeWALT
Instruction Manual
Guide D’utilisation
Manual de instrucciones
ENGLISH
B
Components
1 Trigger switch
2 Operating handle
3 Battery
4 Battery release button
5 Mounting holes
6 Lower guard
7 Miter lock handle
8 Miter detent latch
9 Miter scale
10 Miter scale screws
11 Hand indentations
12 Fence
13 Bevel lock knob
14 Stabalizer
15 Lifting handle
16 Fence adjustment knob
17 Dust port
18 Table
19 Head lock knob
20 Base
21 XPS On switch
22 Wing nut
23 Vertical material clamp
24 Rails
25 Depth stop
26 Kerf plate
27 Miter pointer screw
28 0° bevel stop
29 Depth adjustment screw
30 Rail lock knob
31 Miter scale pointer
32 Extension
English (original instructions) 7
Français (traduction de la notice d’instructions originale) 18
Español (traducido de las instrucciones originales) 30
Composantes
1 Gâchette
2 Poignée de manœuvre
3 Bloc‑piles
4 Bouton de libération de la pile
5 Trous de montage
6 Protecteur inférieur
7 Poignée de verrouillage des onglets
8 Verrou du cran des onglets
9 Échelle des onglets
10 Vis de l’échelle des onglets
11 Encoches pour mains
12 Guide
13 Bouton de verrouillage en biseau
14 Stabilisateur
15 Poignée de levage
16 Bouton de réglage du guide
17 Capteur de poussière
18 Table
19 Bouton de verrouillage de la tête
20 Base
21 Interrupteur de XPS
22 Écrou papillon
23 Serre‑joint vertical du matériau
24 Glissières
25 Butée de profondeur
26 Plaque à entaille
27 Vis du pointeur d’onglet
28 Butée de biseau à 0°
29 Vis d’ajustement de la profondeur
30 Bouton de verrouillage des glissières
31 Pointeur d’échelle d’onglet
32 Rallonge
Componentes
1 Interruptor de gatillo
2 Manija de operación
3 Batería
4 Botón de liberación de batería
5 Orificios de montaje
6 Protección inferior
7 Manija de bloqueo de inglete
8 Seguro de tope de inglete
9 Escala de inglete
10 Tornillos de escala de inglete
11 Indentaciones de mano
12 Cerca
13 Perilla de bloqueo de bisel
14 Estabilizador
15 Manija de elevación
16 Perilla de ajuste de cerca
17 Puerto de polvo
18 Banco
19 Perilla de bloqueo de cabeza
20 Base
21 Interruptor de encendido XPS
22 Tuerca de mariposa
23 Abrazadera de material vertical
24 Rieles
25 Tope de profundidad
26 Placa de corte de sierra
27 Tornillo de puntero de inglete
28 Tope de bisel de 0°
29 Tornillo de ajuste de profundidad
30 Perilla de bloqueo de riel
31 Puntero de escala de inglete
32 Extensión
1
Fig. A
1
2
6
5
5
5
9
10
8
7
11
11
12
13
17
15
18
16
20
21
25
22
29
24
26
31
27
28
30
32
32
32
32
14
23
19
3
4
5
2
Fig.B Fig.C
Fig.D Fig.E
Fig.F Fig.G
15 63
32
36
38
40
37
39
40
57
56
75–100% charged
Chargé de 75 à 100 %
75–100% cargada
51–74% charged
Chargé de 51 à 74 %
51–74% cargada
< 50% charged
Chargé de < 50 %
< 50% cargada
Pack needs to be charged
Le bloc‑piles doit être rechargé
La batería tiene que cargarse
Indicators/Témoin/Indicador
Charging
Bloc‑piles en Cours
de Chargement
Unidad en Proceso de Carga
Fully Charged
Bloc‑piles Chargé
Unidad Cargada
Hot/Cold Pack Delay
Suspension de Charge Contre
le Chaud/Froid
Restraso por Unidad Caliente/
Fría
14
62 62
33
3
Fig.H Fig.I
Fig.J Fig.K
Fig.L1 Fig.L3
Fig.L2
Fig.M
42
43
44
46
45
47
61
61
12
8
7
18
19
13
48 49
51
50
64
61
4
1
1
2
Angle “A”
Fig.N Fig.O
Fig.P Fig.Q
Fig.R Fig.S
41
1
52
17
17
53
5
Fig.T Fig.U
Fig.V
Fig.X Fig.Y
Fig.W
12
39
39
12
18
12
18
12
6
Fig.Z
7
ENGLISH
h ) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause severe
injury within a fraction of asecond.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it wasdesigned.
b ) Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must berepaired.
c ) Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power toolaccidentally.
d ) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrainedusers.
e ) Maintain power tools and accessories. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained powertools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier tocontrol.
g ) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardoussituation.
h ) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the
tool in unexpectedsituations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
batterypack.
b ) Use power tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury andfire.
c ) When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together
may cause burns or afire.
d ) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irritation
orburns.
e ) Do not use a battery pack or tool that is damaged or modified. Damaged or
modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk
ofinjury.
f ) Do not expose a battery pack or tool to fire or excessive temperature. Exposure to
fire or temperature above 265°F (130°C) may causeexplosion.
g ) Follow all charging instructions and do not charge the battery pack or tool
outside the temperature range specified in the instructions. Charging improperly
or at temperatures outside the specified range may damage the battery and increase the
risk offire.
6) Service
a ) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool ismaintained.
b ) Never service damaged battery packs. Service of battery packs should only be
performed by the manufacturer or authorized serviceproviders.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed below may result
in electric shock, fire and/or seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains‑operated (corded) power tool or
battery‑operated (cordless) powertool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark areas inviteaccidents.
b ) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
orfumes.
c ) Keep children and bystanders away while operating a power tool. Distractions can
cause you to losecontrol.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electricshock.
b ) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed orgrounded.
c ) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electricshock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electricshock.
e ) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electricshock.
f ) If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of
electricshock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personalinjury.
b ) Use personal protective equipment. Always wear eye protection. Protective
equipment such as a dust mask, non‑skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personalinjuries.
c ) Prevent unintentional starting. Ensure the switch is in the off‑position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have
the switch on invitesaccidents.
d ) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personalinjury.
e ) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpectedsituations.
f ) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught
in movingparts.
g ) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust‑relatedhazards.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to
hazardous situations and your risk of personal injury or propertydamage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in death or seriousinjury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result
in death or seriousinjury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderateinjury.
(Used without word) Indicates a safety relatedmessage.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in propertydamage.
Intended Use
This heavy duty miter saw is designed for professional wood cuttingapplications.
This miter saw is a professional power tool.
DO NOT use under wet conditions or in presence of flammable liquids orgases.
DO NOT let children come into contact with the tool. Supervision is required when
inexperienced operators use thistool.
English (original instructions)
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or seriousinjury.
WARNING: To reduce the risk of injury, read the instructionmanual.
Safety Instructions for Miter Saws
a ) Miter saws are intended to cut wood or wood‑like products, they cannot be used
with abrasive cut‑off wheels for cutting ferrous material such as bars, rods, studs,
etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from
abrasive cutting will burn the lower guard, the kerf insert and other plasticparts.
b ) Use clamps to support the workpiece whenever possible. If supporting the
workpiece by hand, you must always keep your hand at least 4" (100 mm) from
either side of the saw blade. Do not use this saw to cut pieces that are too small to
be securely clamped or held by hand. If your hand is placed too close to the saw blade,
there is an increased risk of injury from bladecontact.
c ) The workpiece must be stationary and clamped or held against both the fence
and the table. Do not feed the workpiece into the blade or cut “freehand” in any
way. Unrestrained or moving workpieces could be thrown at high speeds, causinginjury.
d ) Push the saw through the workpiece. Do not pull the saw through the workpiece.
To make a cut, raise the saw head and pull it out over the workpiece without
cutting, start the motor, press the saw head down and push the saw through the
workpiece. Cutting on the pull stroke is likely to cause the saw blade to climb on top of
the workpiece and violently throw the blade assembly towards theoperator.
e ) Never cross your hand over the intended line of cutting either in front or behind
the saw blade. Supporting the workpiece “cross handed” i.e. holding the workpiece to the
right of the saw blade with your left hand or vice versa is verydangerous.
f ) Do not reach behind the fence with either hand closer than 4" (100 mm) from
either side of the saw blade, to remove wood scraps, or for any other reason while
ENGLISH
8
DO NOT REACH UNDERNEATH THE SAW unless it is unplugged and turned off. Contact
with saw blade may cause personalinjury.
SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Vibration can possibly cause
the machine to slide, walk, or tip over, causing seriousinjury.
USE ONLY CROSSCUT SAW BLADES recommended for miter saws. For best results, do not
use carbide tipped blades with hook angles in excess of 7degrees. Do not use blades with deep
gullets. These can deflect and contact the guard, and can cause damage to the machine and/
or seriousinjury.
USE ONLY BLADES OF THE CORRECT SIZE AND TYPE specified for this tool to prevent
damage to the machine and/or seriousinjury.
INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or damaged
blade can come apart and pieces can be thrown at high speeds, causing serious injury.
Replace cracked or damaged bladesimmediately.
CLEAN THE BLADE AND BLADE CLAMPS prior to operation. Cleaning the blade and blade
clamps allows you to check for any damage to the blade or blade clamps. A cracked or
damaged blade or blade clamp can come apart and pieces can be thrown at high speeds,
causing seriousinjury.
DO NOT USE WARPED BLADES. Check to see if the blade runs true and is free from vibration.
A vibrating blade can cause damage to the machine and/or seriousinjury.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.
KEEP GUARD IN PLACE and in workingorder.
ALWAYS USE THE KERF PLATE AND REPLACE THIS PLATE WHEN DAMAGED. Small
chip accumulation under the saw may interfere with the saw blade or may cause instability of
workpiece whencutting.
USE ONLY BLADE CLAMPS SPECIFIED FOR THIS TOOL to prevent damage to the machine
and/or seriousinjury.
CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can cause the
machine to overheat, damaging the machine and possibly causing a short which could cause
seriousinjury.
NEVER LOCK THE SWITCH IN THE “ON” POSITION. Severe personal injury mayresult.
NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool
is unintentionallycontacted.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until
it comes to a completestop.
DO NOT USE ABRASIVE WHEELS OR BLADES. The excessive heat and abrasive particles
generated by them may damage the saw and cause personalinjury.
ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e.,
a safety video) is available from the Power Tool Institute, 1300Sumner Avenue, Cleveland,
OH 44115‑2851 (www.powertoolinstitute.com). Information is also available from the
National Safety Council, 1121Spring Lake Drive, Itasca, IL 60143‑3201. Please refer to the
American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor OSHA 1910.213Regulations.
WARNING: Cutting plastics, sap coated wood, and other materials may cause melted
material to accumulate on the blade tips and the body of the saw blade, increasing the
risk of blade overheating and binding whilecutting.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETYEQUIPMENT:
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
ANSI S12.6 (S3.19) hearing protection,
NIOSH/OSHA/MSHA respiratoryprotection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicalsare:
lead from lead‑based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically‑treatedlumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopicparticles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmfulchemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face andbody.
WARNING: Always wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from
this product may contribute to hearingloss.
Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long
hair can be caught in movingparts.
the blade is spinning. The proximity of the spinning saw blade to your hand may not be
obvious and you may be seriouslyinjured.
g ) Inspect your workpiece before cutting. If the workpiece is bowed or warped,
clamp it with the outside bowed face toward the fence. Always make certain
that there is no gap between the workpiece, fence and table along the line of
the cut. Bent or warped workpieces can twist or shift and may cause binding on
the spinning saw blade while cutting. There should be no nails or foreign objects in
theworkpiece.
h ) Do not use the saw until the table is clear of all tools, wood scraps, etc., except
for the workpiece. Small debris or loose pieces of wood or other objects that contact the
revolving blade can be thrown with highspeed.
i ) Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately
clamped or braced and may bind on the blade or shift duringcutting.
j ) Ensure the miter saw is mounted or placed on a level, firm work surface before
use. A level and firm work surface reduces the risk of the miter saw becomingunstable.
k ) Plan your work. Every time you change the bevel or miter angle setting, make
sure the fence will not interfere with the blade or the guarding system. Without
turning the tool “ON” and with no workpiece on the table, move the saw blade through
a complete simulated cut to assure there will be no interference or danger of cutting
thefence.
l ) Provide adequate support such as table extensions, saw horses, etc. for a
workpiece that is wider or longer than the table top. Workpieces longer or wider
than the miter saw table can tip if not securely supported. If the cut‑off piece or workpiece
tips, it can lift the lower guard or be thrown by the spinningblade.
m ) Do not use another person as a substitute for a table extension or as additional
support. Unstable support for the workpiece can cause the blade to bind or the workpiece
to shift during the cutting operation pulling you and the helper into the spinningblade.
n ) The cut‑off piece must not be jammed or pressed by any means against the
spinning saw blade. If confined, i.e. using length stops, the cut‑off piece could get
wedged against the blade and thrownviolently.
o ) Always use a clamp or a fixture designed to properly support round material such
as rods or tubing. Rods have a tendency to roll while being cut, causing the blade to
“bite” and pull the work with your hand into theblade.
p ) Let the blade reach full speed before contacting the workpiece. This will reduce the
risk of the workpiece beingthrown.
q ) If the workpiece or blade becomes jammed, turn the miter saw off. Wait for
all moving parts to stop and disconnect the plug from the power source and/
or remove the battery pack. Then work to free the jammed material. Continued
sawing with a jammed workpiece could cause loss of control or damage to the mitersaw.
r ) After finishing the cut, release the switch, hold the saw head down and wait for
the blade to stop before removing the cut‑off piece. Reaching with your hand near
the coasting blade isdangerous.
s ) Hold the handle firmly when making an incomplete cut or when releasing the
switch before the saw head is completely in the down position. The braking action
of the saw may cause the saw head to be suddenly pulled downward, causing a risk
ofinjury.
Additional Safety Rules for Miter Saws
WARNING: Do not allow familiarity (gained from frequent use of your saw) to replace
safety rules. Always remember that a careless fraction of a second is sufficient to inflict
severeinjury.
WARNING: Never modify the power tool or any part of it. Damage or personal injury
couldresult.
DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according
to the instructions. A machine incorrectly assembled can cause seriousinjury.
OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not
thoroughly familiar with the operation of this machine. Knowledge issafety..
MAKE CERTAIN the blade rotates in the correct direction. The teeth on the blade should point
in the direction of rotation as marked on thesaw.
TIGHTEN ALL CLAMP HANDLES, knobs and levers prior to operation. Loose clamps can
cause parts or the workpiece to be thrown at highspeeds.
BE SURE all blade and blade clamps are clean, recessed sides of blade clamps are against
blade and arbor screw is tightened securely. Loose or improper blade clamping may result in
damage to the saw and possible personalinjury.
DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTAGE for the
saw. Overheating, damage to the tool and personal injury mayoccur.
DO NOT WEDGE ANYTHING AGAINST THE FAN to hold the motor shaft. Damage to tool
and possible personal injury mayoccur.
NEVER CUT FERROUS METALS or masonry. Either of these can cause the carbide tips to fly
off the blade at high speeds causing seriousinjury.
NEVER PLACE HANDS CLOSER THAN 4" (100 mm) FROM THEBLADE.
NEVER HAVE ANY PART OF YOUR BODY IN LINE WITH THE PATH OF THE SAW
BLADE. Personal injury willoccur.
NEVER APPLY BLADE LUBRICANT TO A RUNNING BLADE. Applying lubricant could
cause your hand to move into the blade resulting in seriousinjury.
DO NOT place either hand in the blade area when the saw is connected to the power source.
Inadvertent blade activation may result in seriousinjury.
NEVER REACH AROUND OR BEHIND THE SAW BLADE. A blade can cause seriousinjury.
9
ENGLISH
The RBRC® Seal
Please take your spent battery packs to an authorized DeWALT service center
or to your local retailer for recycling. In some areas, it is illegal to place spent
battery packs in the trash. You may also contact your local recycling center
for information on where to drop off the spent battery pack. Do not place
in curbside recycling. For more information visit www.call2recycle.org. or call the toll free
number in the RBRC®Seal.
RBRC® is a registered trademark of Call 2Recycle,Inc.
Shipping the DeWALT FLEXVOLT® Battery Pack
The DeWALT FLEXVOLT® battery pack has a battery cap that should be used when shipping
the batterypack.
Attach the cap to the battery pack to ready it for shipping. This converts the battery pack to
three separate 20V batteries. The three batteries have the Watt hour rating labeled “Shipping”
on the battery pack. If shipping without the cap or in a tool, the pack is one battery at the Watt
hour rating labeled“Use”.
Example battery pack label:
USE: 120 Wh SHIPPING: 3 x 40 Wh
In this example, the battery pack is three batteries with 40Watt hours each when using the
cap. Otherwise, the battery pack is one battery with 120Watthours.
Follow all charging instructions and do not charge the battery pack or appliance
outside of the temperature range specified in the instructions. Charging improperly or
at temperatures outside of the specified range may damage the battery and increase the risk
offire.
If battery contents come into contact with the skin, immediately wash area with
mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for
15minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is
composed of a mixture of liquid organic carbonates and lithiumsalts.
Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If
symptoms persist, seek medicalattention.
Battery liquid may be flammable if exposed to spark orflame.
Never attempt to open the battery pack for any reason. If the battery pack case is
cracked or damaged, do not insert into the charger. Do not crush, drop or damage
the battery pack. Do not use a battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped
on). Damaged battery packs should be returned to the service center forrecycling.
Storage Recommendations
The best storage place is one that is cool and dry, away from direct sunlight and excess heat or
cold. Store the fully charged battery pack out of thecharger.
Battery Pack Cleaning Instructions
Dirt and grease may be removed from the exterior of the battery pack using a cloth or soft
non‑metallic brush. Do not use water or any cleaningsolutions.
Fuel Gauge Battery Packs (Fig. B)
Some battery packs include a fuel gauge. When the fuel gauge button is pressed and held,
the LED lights will indicate the approximate level of charge remaining. This does not indicate
tool functionality and is subject to variation based on product components, temperature, and
end‑userapplication.
Transportation
WARNING: Fire hazard. Do not store, carry, or transport the battery pack so that
metal objects can contact exposed battery terminals. For example, do not place the
battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose
nails, screws, keys, coins, hand tools, etc. When transporting individual battery packs,
make sure that the battery terminals are protected and well insulated from materials that
could contact them and cause a short circuit. NOTE: Li‑ion battery packs should not be
put in checked baggage on airplanes and must be properly protected from short circuits if
they are in carry‑onbaggage.
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below and then follow charging proceduresoutlined.
When ordering replacement battery packs, be sure to include the catalog number andvoltage.
For your convenience and safety, the following warning labels are on your mitersaw.
ON THE UPPER GUARD:
TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL. WEAR EYE
PROTECTION AND RESPIRATORY PROTECTION. USE ONLY IDENTICAL REPLACEMENT
PARTS. DO NOT EXPOSE TO RAIN OR USE IN DAMPLOCATIONS.
ON FENCE:
ALWAYS ADJUST FENCE PROPERLY BEFORE USE. CLAMP SMALL PIECES BEFORE
CUTTING. SEEMANUAL.
ON GUARD:
DANGER–KEEP AWAY FROMBLADE.
ON TABLE: (2 PLACES)
WARNING: KEEP HANDS AND BODY OUT OF THE PATH OF THE
SAW BLADE. CONTACT WITH BLADE WILL RESULT IN SERIOUS
INJURY. DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.
CHECK GUARDING SYSTEM TO MAKE SURE IT IS FUNCTIONING
CORRECTLY. DO NOT PERFORM ANY OPERATION FREEHAND.
NEVER REACH IN BACK OF SAW BLADE TURN OFF TOOL AND
WAIT FOR SAW BLADE TO STOP BEFORE MOVING WORKPIECE OR
CHANGING SETTINGS OR MOVING HANDS. NEVER CROSS ARMS
IN FRONT OF BLADE. ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE EACH USE.
DISCONNECT POWER BEFORE CHANGING BLADE ORSERVICING.
ON TABLE: (2 PLACES)
The label on your tool may include the following symbols. The symbols and their definitions are
asfollows:
V ......................... volts
Hz .......................hertz
min ..................... minutes
or DC ......direct current
...................... Class I Construction (grounded)
…/min ..............per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................watts
Wh ......................watt hours
Ah ....................... amp hours
or AC ...........alternating current
or AC/DC .... alternating or direct current
...................... Class II Construction (double insulated)
no .......................no load speed
n .........................rated speed
PSI....................... pounds per square inch
......................earthing terminal
.....................safety alert symbol
..................... visible radiation
do not stare into the light
..................... wear respiratory protection
..................... wear eye protection
..................... wear hearing protection
..................... read all documentation
..................... do not expose to rain
READ ALL INSTRUCTIONS
Important Safety Instructions for All Battery Packs
WARNING: Read all safety warnings, instructions, and cautionary markings
for the battery pack, charger and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/or seriousinjury.
Do not charge or use the battery pack in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Inserting or removing the battery pack from
the charger may ignite the dust orfumes.
NEVER force the battery pack into the charger. DO NOT modify the battery pack in
any way to fit into a non‑compatible charger as battery pack may rupture causing
serious personal injury. Consult the chart at the end of this manual for compatibility of
batteries andchargers.
Charge the battery packs only in DeWALTchargers.
DO NOT splash or immerse in water or otherliquids.
DO NOT allow water or any liquid to enter batterypack.
Do not store or use the tool and battery pack in locations where the temperature
may reach or exceed 104°F (40°C) (such as outside sheds or metal buildings in
summer). For best life store battery packs in a cool, drylocation.
NOTE: Do not store the battery packs in a tool with the trigger switch locked on.
Never tape the trigger switch in the ONposition.
Do not incinerate the battery pack even if it is severely damaged or is completely
worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when
lithium‑ion battery packs areburned.
Do not expose a battery pack or appliance to fire or excessive temperature. Exposure
to fire or temperature above 265°F (130°C) may causeexplosion.
Important Safety Instructions for All Battery Chargers
WARNING: Read all safety warnings, instructions, and cautionary markings
for the battery pack, charger and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/or seriousinjury.
DO NOT attempt to charge the battery pack with any chargers other than a DeWALT
charger. DeWALT chargers and battery packs are specifically designed to worktogether.
These chargers are not intended for any uses other than charging DeWALT
rechargeable battery packs. Charging other types of battery packs may cause them
to overheat and burst, resulting in personal injury, property damage, fire, electric shock
orelectrocution.
Do not expose the charger to rain orsnow.
Do not allow water or any liquid to entercharger.
Pull by the plug rather than the cord when disconnecting the charger. This will reduce
the risk of damage to the electric plug andcord.
Make sure that the cord is located so that it will not be stepped on, tripped over or
otherwise subjected to damage orstress.
ENGLISH
10
Specifications
Capacity of cut
50° miter left and 60° miter right
49º bevel left and right
0° miter
Max. Height 4.4" (112 mm) Resulting Width 10.9" (278 mm)
Max. Width 12.2" (310 mm) Resulting Height 3.5" (90mm)
45° miter
Max. Height 4.4" (112 mm) Resulting Width 7.7" (197 mm)
Max. Width 8.6" (219 mm) Resulting Height 3.5" (90 mm)
45° bevel ‑ Left
Max. Height 2.4" (60 mm) Resulting Width 10.9" (278 mm)
Max. Width 12.2" (310 mm) Resulting Height 2.1" (54 mm)
45º bevel ‑ Right
Max. Height 2.0" (50 mm) Resulting Width 11.65" (296 mm)
Max. Width 12.2" (310 mm) Resulting Height 1.6" (40 mm)
Your saw is capable of cutting baseboard moldings 0.75" (19mm) thick by 6.5" (165mm) tall
on a 45° right or leftmiter.
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts. In
addition to this instruction manual, the carton should contain:
1 DCS781 miter saw
1 Stabilizer bar
1 Vacuum adapter
1
DeWALT 12" (305 mm) diameter saw blade
2 Base extensions
1 Material clamp
1 Charger (Kit only)
1 Battery (Kit only)
In bag:
1 Dust bag
1 Blade wrench
1 Instruction manual
NOTE: Your miter saw is fully and accurately adjusted at the factory at the time of
manufacture. If readjustment due to shipping and handling or any other reason is required,
follow the steps below to adjust yoursaw.
Once made, these adjustments should remain accurate. Take a little time now to follow these
directions carefully to maintain the accuracy of which your saw iscapable.
Wall Mounting
Some DeWALT chargers are designed to be wall mountable or to sit upright on a table or
work surface. If wall mounting, locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede air flow. Use the back of the
charger as a template for the location of the mounting screws on the wall. Mount the charger
securely using drywall screws (purchased separately) at least 1” (25.4mm) long, with a screw
head diameter of 0.28–0.35” (7–9mm), screwed into wood to an optimal depth leaving
approximately 7/32” (5.5 mm) of the screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
2. The charger and battery pack may become warm to the touch while charging. This is a
normal condition, and does not indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in a warm environment such as in
a metal shed or an uninsulatedtrailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when
you turn out the lights;
c. If charging problems persist, take the tool, battery pack and charger to your local
servicecenter.
4. You may charge a partially used pack whenever you desire with no adverse effect on the
batterypack.
Charger Cleaning Instructions
WARNING:Shock hazard. Disconnectthe charger from the AC outlet before cleaning.
Dirt and grease may be removed from the exterior of the charger using a cloth or soft
non‑metallic brush. Do not use water or any cleaningsolutions.
Do not use an extension cord unless it is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric shock orelectrocution.
When operating a charger outdoors, always provide a dry location and use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the
risk of electricshock.
An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the heavier the cord and thus the greater
its capacity. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The following table shows the correct size to use depending on total length of
all extension cords plugged together, and nameplate ampere rating. If in doubt, use the next
heaviergauge.
Minimum Gauge for Cord Sets
Volts Total Length of Cord in Feet
(meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
Ampere Rating
American Wire Gauge
More Than Not More
Than
0 6 18 16 16 14
610 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
Do not place any object on top of the charger or place the charger on a soft surface
that might block the ventilation slots and result in excessive internal heat. Place the
charger in a position away from any heat source. The charger is ventilated through slots in the
top and the bottom of thehousing.
Do not operate the charger with a damaged cord orplug. Have them
replacedimmediately.
Do not operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way. Take it to an authorized servicecenter.
Do not disassemble the charger; take it to an authorized service center when service
or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution
orfire.
The charger is designed to operate on standard 120V household electrical power. Do
not attempt to use it on any other voltage. This does not apply to the vehicularcharger.
Foreign materials of a conductive nature, such as, but not limited to, grinding dust,
metal chips, steel wool, aluminum foil or any buildup of metallic particles should be
kept away from the charger cavities and ventilation slots.
Always unplug the charger from the power supply when there is no battery pack in
thecavity.
Charging a Battery (Fig. C).
1. Plug the charger into an appropriate outlet.
2. Insert and fully seat battery pack. The red charging light(s) will continuously blink
whilecharging.
3. Charging is complete when the red charging light(s) remain(s) continuously ON. Battery
pack can be left in charger or removed. Some chargers require the battery pack release
button to be pressed forremoval.
WARNING: Only charge batteries in air temperature over 40°F (4.5° C) and below 104°F
(+40°C).
4. Charger will not charge a faulty battery pack, which may be indicated by the charging
light(s) staying OFF. Take charger and battery pack to an authorized service center if
light(s) stay(s)OFF.
NOTE: Refer to label near charging light(s) on charger for blinkpatterns. Older chargers
may have additional information and/or may not have a yellow indicatorlight.
NOTE: To remove the battery pack, some chargers require the battery pack release button
to bepressed.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it automatically starts a
Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the pack charging mode. This feature
ensures maximum battery packlife.
A cold battery pack may charge at a slower rate than a warm batterypack.
The hot/cold pack delay will be indicated by the red light(s) continuing to blink but with the
yellow light continuously ON. Once the battery pack has reached an appropriate temperature,
the yellow light will turn OFF and the charger will resume the chargingprocedure.
DCB118 and DCB1112 Chargers
The DCB118 and DCB1112 chargers are equipped with an internal fan designed to cool the
battery pack. The fan will turn on automatically when the battery pack needs to becooled.
Never operate the charger if the fan does not operate properly or if ventilation slots are
blocked. Do not permit foreign objects to enter the interior of thecharger.
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection System that will protect the battery
pack against overloading, overheating or deep discharge. The tool will automatically turn off
and the battery pack will need to berecharged.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 65°F – 75°F (18° C– 24°C). DO NOT charge when the battery
pack is below +40°F (+4.5°C), or above +104°F (+40°C). This is important and will
prevent serious damage to the batterypack.
11
ENGLISH
Changing or Installing a New Saw Blade (Fig. A, G)
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
Adjusting the Bevel Stop to 22.5 ° (or 33.9 °) (Fig. A, J)
NOTE: Adjust the bevel angles only after performing the 0° bevel angle and bevel
pointeradjustment.
To set the left 22.5° bevel angle, flip out the left 22.5° bevel pawl47. Loosen the bevel
lock knob13 and tilt the head fully to the left. If the bevel pointer does not indicate
exactly 22.5°, turn the crown adjustment screw46 contacting the pawl with a 7/16”
wrench until the bevel pointer reads 22.5°.
To adjust the right 22.5° bevel angle, flip out the right 22.5° bevel pawl. Loosen the bevel
lock knob and pull the 0° bevel stop and rotate 90degrees to override the 0° bevel stop.
When the saw is fully to the right, if the bevel pointer does not indicate exactly 22.5°,
turn the crown adjustment screw contacting the pawl with a 7/16” wrench until the bevel
pointer indicates exactly22.5°.
Adjusting the Bevel Stop to 45 ° Left or Right (Fig. A, J)
To adjust the right 45° bevel angle, loosen the bevel lock knob13 and pull the 0° bevel stop,
rotate 90° (either clockwise or counterclockwise) and let go for the spring loaded pin to lock
in to override the 0° bevel stop. When the saw is fully to the right, if the bevel pointer does not
indicate exactly 45°, turn the left 45° bevel adjustment screw45 with the 1/2" blade wrench
until the bevel pointer indicates 45°.
To adjust the left 45° bevel stop, first loosen the bevel lock knob and tilt the head to the left. If
the bevel pointer does not indicate exactly 45°, turn the right 45° bevel adjustment screw45
until the bevel pointer43 reads 45°.
Bevel Pointer (Fig. J)
If the bevel pointer43 does not indicate zero, loosen the screw44 that holds it in place and
move the pointer as necessary. Ensure the 0° bevel is correct and the bevel pointers are set
before adjusting any other bevel anglescrews.
Bevel Square to Table (Fig. A, I, J)
To align the blade square to the table18, lock the arm in the down position with the lock
down pin19. Place a square against the blade, ensuring the square is not on top of a tooth.
Loosen the bevel lock knob13 and ensure the arm is firmly against the 0° bevel stop. Rotate
the 0° bevel adjustment screw42 with the 1/2” blade wrench as necessary so that the blade
is at 0° bevel to thetable.
Miter Pointer Adjustment (Fig. A)
Unlock the miter lock handle7 to move the miter arm to the zero position. With the miter
lock handle unlocked, squeeze the miter detent latch8 and allow the miter latch to snap into
place as you rotate the miter arm to zero. Observe the miter pointer31 and miter scale9
shown in FigureA. If the pointer does not indicate exactly zero, loosen the miter pointer
screw27 holding the pointer in place, reposition the pointer and tighten thescrew.
Miter Scale Adjustment (Fig. A, H)
Unlock the miter lock handle7 and swing the miter arm until the miter latch8 locks it at
the 0° miter position. Do not lock the miter lock handle. Place a square against the saw’s
fence and blade, as shown. (Do not touch the tips of the blade teeth with the square. To do
so will cause an inaccurate measure ment.) If the saw blade is not exactly perpendicular to
the fence12, loosen the four miter scale screws10 that hold the miter scale and move the
miter lock handle and the scale left or right until the blade is perpendicular to the fence, as
measured with the square. Retighten the four screws. Pay no attention to the reading of the
miter pointer at thistime.
Assembling the Stabilizer Bar (Fig. F)
Your saw includes one base stabilizer14 This must be installed before using your saw. Insert
the stabilizer into the holes in the back of the unit. Move the stabilizer in or out until it contacts
the work surface. Then tighten the screws62 in the base to fasten thestabilizer.
Bench Mounting (Fig. A)
Mounting holes5 are provided in all 4feet to facilitate bench mounting, as shown in FigureA.
(Two different‑sized holes are provided to accommodate different sizes of screws. Use either
hole, it is not necessary to use both.) Always mount your saw firmly to a stable surface to
prevent movement. To enhance the tool’s portability, it can be mounted to a piece of 1/2”
(12.7 mm) or thicker plywood which can then be clamped to your work support or moved to
other job sites andreclamped.
NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting
screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work
support. When clamping the saw to any work surface, clamp only on the clamping bosses
where the mounting screw holes are located. Clamping at any other point will surely interfere
with the proper operation of thesaw.
CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not
warped or otherwise uneven. If the saw rocks on the surface place a thin piece of material
under one saw foot until the saw sits firmly on the mountingsurface.
Assembling the Base Extensions (Fig. E)
WARNING: Base extensions must be assembled to both sides of the saw's base before
using thesaw.
1. The extension32 should be oriented as shown in Figure E, sliding fully into the
U‑shapedsupports.
2. Clamp the extension’s rods against the miter saw base by inserting the extension
screw63entirely through and the clamp.
3. Repeat steps 1through 3on the other side.
Miter Control (Fig. A)
The miter lock lever and miter detent latch allow you to miter your saw to 60° right and 50°
left. To miter the saw, lift the miter lock handle7, squeeze the miter detent latch8 and
move the miter arm to the angle desired on the miter scale9 as shown at the miter scale
pointer31. Push down on the miter lock lever to lock the miter arm inplace.
Use of CUTLINE™ LED Worklight (Fig. A)
CAUTION: Do not stare into worklight. Serious eye injury couldresult.
NOTE: The battery must be charged and connected to the mitersaw.
The CUTLINE™ LED Worklight can be turned on by the momentary switch21. The light will
automatically turn off within 20seconds if the saw is not in use. The light is also activated
automatically every time the tool's main trigger1 ispulled.
To cut through an existing pencil line on a piece of wood, turn on the CUTLINE™ worklight
using the momentary switch21 (not with the main trigger), then pull down on the operating
handle2 to bring the saw blade close to the wood. The shadow of the blade will appear
on the wood. This shadow line represents the material that the blade will remove when
performing a cut. To correctly locate your cut to the pencil line, align the pencil line with the
edge of the blade’s shadow. Keep in mind that you may have to adjust the miter or bevel
angles in order to match the pencil lineexactly.
Your saw is equipped with a battery monitoring feature. The CUTLINE™ worklight begins
to flash when the battery is near the end of its useful charge and/or when the battery is
too hot. Charge the battery prior to continuing cutting applications. Refer to Charging
Procedure under Important Safety Instructions for All Battery Chargers for battery
charginginstructions.
Familiarization (Fig. A, D)
Your miter saw is not fully assembled in the carton. Refer to Assembling the Base Extensions
and Assembling the Stabilizer Bar sections for assembly instructions. Open the box and lift
the saw out by the convenient lifting handle15, as shown in FigureD.
Place the saw on a smooth, flat surface such as a workbench or strongtable.
Examine Figure A to become familiar with the saw and its various parts. The section on
adjustments will refer to these terms and you must know what and where the partsare.
CAUTION: Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle
when pulling the handle down. The lower guard will move up as the handle is pulled
down which could cause pinching. The handle is placed close to the guard for specialcuts.
Press down lightly on the operating handle2 and pull the head lock knob19 and rotate
90degrees. Gently release the downward pressure and hold the arm allowing it to rise to its
full height. Use the head lock knob when carrying the saw from one place to another. Always
use the lifting handle15 to transport the saw or the hand indentations11 shown in FigureA.
Drive
60Volt motor
3800RPM
Cut helical gears and bevel gears
Carbide tooth blade
Automatic electric brake
CAUTION:
Never depress the spindle lock button while the blade is under power orcoasting.
Do not cut ferrous metal (containing iron or steel) or masonry or fiber cement product
with this mitersaw.
Removing the Blade (Fig. A, G)
1. Remove battery pack3 from thesaw.
2. Raise the arm to the upper position and raise the lower guard6 as far aspossible.
3. Depress the spindle lock button36 while carefully rotating the saw blade by hand until
the lockengages.
4. Using your finger, pivot the blade bolt plate38 to gain access to blade bolt head40.
5. Keeping the spindle lock button depressed and blade bolt plate pushed out of the way,
use the blade wrench37 provided to loosen blade screw. (Turn clockwise, left‑hand
threads.) Remove the blade screw. 
6. Proceed to remove the outer clamp washer, blade adaptor and sawblade.
Installing a Blade (Fig. A, G)
1. Remove battery pack3 from thesaw.
2. Raise the saw head to the upper position and raise the lower guard6 as far as possible.
Place the blade39 on the spindle, following by the blade adaptor57 then outer clamp
washer56. Make sure to match arrow direction on blade with the arrow direction on
guardplate.
3. Depress the spindle lock button36 while carefully rotating the saw blade by hand until
the lockengages.
4. Using your finger, push back the blade bolt plate38 to gain access to blade bolt head40.
5. Keeping the spindle lock button depressed and blade bolt plate pushed out of the
way, use the blade wrench37 provided to firmly tighten the blade screw. (Turn
counter‑clockwise, left‑hand threads.)
ENGLISH
12
Body and Hand Position (Fig. M)
WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position
asshown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation
of a suddenreaction.
Proper positioning of your body and hands when operating the miter saw will make cutting
easier, more accurate and safer. Never place hands near cutting area. Place hands no closer
than 4" (100mm) from the blade. Hold the workpiece tightly to the table and the fence
when cutting. Keep hands in position until the trigger has been released and the blade has
Installing and Removing the Battery Pack (Fig. A)
WARNING: Ensure the tool/appliance is in the off position before inserting the
batterypack.
NOTE: For best results, make sure your battery pack is fullycharged.
To install the battery pack3 into the tool handle, align the battery pack with the rails inside
the tool’s handle and slide it into the handle until the battery pack is firmly seated in the tool
and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release button4 and firmly pull the
battery pack out of the tool handle. Insert it into the charger as described in the charger
section of thismanual.
WARNING: Always use eye protection. All users and bystanders must wear eye protection
that conforms to ANSI Z87.1 (CAN/CSA Z94.3).
WARNING: To ensure the blade path is clear of obstructions, always make a dry run of the
cut without power before making any cuts on theworkpiece.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
the saw can bevel past these stops. When the 45° stops are needed, pull the 45° bevel
override leverforward.
Crown Bevel Pawls (Fig. J)
When cutting crown molding laying flat, your saw is equipped to accurately and rapidly set
a crown stop, left or right (refer to Instructions for Cutting Crown Molding Laying Flat
and Using the Compound Features). The crown bevel pawl51 can be rotated to contact
the crown adjustment screw46. The saw is factory set to be used for typical crown in North
America (52/38), but can be reversed to cut non‑typical (45/45) crown. To reverse the crown
bevel pawl, remove the retaining screw, the 22.5° bevel pawl and the 33.9° crown bevel pawl.
Flip the crown bevel pawl so the 30° is facing up. Reattach the screw to secure the 22.5°
bevel pawl and the crown bevel pawl. The accuracy setting will not beaffected.
22.5 ° Bevel Pawls (Fig. J)
Your saw is equipped to rapidly and accurately set a 22.5° bevel, left or right. The 22.5° bevel
pawl47can be rotated to contact the crown adjustmentscrew.
Rail Lock Knob (Fig. A)
The rail lock knob30 allows you to lock the saw head firmly to keep it from sliding on the rails.
This is necessary when making certain cuts or when transporting thesaw.
Depth Stop (Fig. A)
The depth stop25 allows the depth of cut of the blade to be limited. The stop is useful for
applications such as grooving and tall vertical cuts. Rotate the depth stop forward and adjust
the depth adjustment screw29 to set the desired depth of cut. To secure the adjustment,
tighten the wing nut22. Rotating the depth stop to the rear of the saw will bypass the depth
stop feature. If the depth adjustment screw is too tight to loosen by hand, the provided blade
wrench can be used to loosen thescrew.
Slide Lock Transport Lever (Fig. L1–L3)
Slide Lock Position (Fig.L1)
The slide lock transport lever61 in forward location locks saw for maximize vertical
cuttingcapacity.
Transport Position (Fig.L2)
The slide lock transport lever61 in rear location locks saw in the transport position to secure
the saw head during transport and storage. Recommended for relocating or carrying thesaw.
Stow Position (Fig.L3)
When not in use, the slide lock transport lever61 can be placed in a stow position. The slide
lock lever locks in place using an indent on the back of the lever that slides up the ramp and
falls into the cast pocket64. To unlock the lever, slightly pull the lever till it clears out of the
cast pocket and rotateclockwise.
Automatic Electric Brake
Your saw is equipped with an automatic electric blade brake which stops the saw blade within
5seconds of trigger release. This is notadjustable.
On occasion, there may be a delay after trigger release to brake engagement. On rare
occasions, the brake may not engage at all and the blade will coast to astop.
If a delay or “skipping” occurs, turn the saw on and off 4or 5times. If the condition persists,
have the tool serviced by an authorized DeWALT servicecenter.
Always be sure the blade has stopped before removing it from the kerf. The brake is
not a substitute for guards or for ensuring your own safety by giving the saw your
completeattention.
FEATURES AND CONTROLS
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
Transporting the Saw (Fig. A)
WARNING: To reduce the risk of serious personal injury, turn tool off, remove the
battery pack, and place lock lever in the transport position before transporting,
making any adjustments, cleaning, repairing, or removing/installing
attachments or accessories. An accidental start‑up can causeinjury.
WARNING: To reduce the risk of serious personal injury, ALWAYS lock the rail lock
knob30, miter lock handle7, bevel lock knob13, head lock knob19 and fence
adjustment knobs16 before transportingsaw.
In order to conveniently carry the miter saw from place to place, a lifting handle15 has been
included on the top of the saw arm and hand indentations11 in thebase.
Head Lock Knob (Fig. A)
WARNING: The head lock knob should be used ONLY when carrying or storing the
saw. NEVER use the headlock knob for any cuttingoperation.
To lock the saw head in the down position, push the head down, rotate head lock knob19
90° and the spring loaded pin will lock in and release the saw head. This will hold the saw
head safely down for moving the saw from place toplace.
To release, press the saw head down, pull out the head lock knob and rotate 90°.
Miter Lock Adjustment (Fig. A, K)
The miter lock rod48 should be adjusted if the table of the saw can be moved when the
miter lock handle7 is locked (down). To adjust the miter lock49, put the miter lock handle
in the unlocked (up) position. Using a slotted screwdriver, adjust the lock rod in 1/8 clockwise
turn increments to increase the lock force. To ensure the miter lock is functioning properly,
re‑lock the miter lock handle to a non‑detent miter angle – for example , 34° ‑ and make sure
the table will notrotate.
Rail Guide Adjustment (Fig. A, F)
Periodically check the rails24 for any play or clearance. The right rail can be adjusted with the
rail set screw33 shown in FigureF. To reduce clearance, use a 4 mm hex wrench and rotate
the rail set screw clockwise gradually while sliding the saw head back and forth. Reduce play
while maintaining minimum slideforce.
Guard Actuation and Visibility (Fig. A, Z)
CAUTION: Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle
when pulling the handle down. The lower guard will move up as the handle is pulled
down which could causepinching.
The lower guard6 on your saw has been designed to automatically uncover the blade when
the arm is brought down and to cover the blade when the arm israised.
The guard can be raised by hand when installing or removing saw blades or for inspection of
the saw. NEVER RAISE THE LOWER GUARD MANUALLY UN LESS THE BLADE ISSTOPPED.
NOTE: Certain special cuts of large material will require that you manually raise the guard.
Refer to Cutting Large Material under SpecialCuts.
The front section of the guard is louvered for visibility while cutting. Although the louvers
dramatically reduce flying debris, they are openings in the guard and safety glasses should be
worn at all times when viewing through thelouvers.
Fence Adjustment (Fig. A)
In order that the saw can bevel to many bevel positions, one of the fences may have to be
adjusted to provide clearance. To adjust each fence, loosen the fence adjustment knob16
and slide the fence outward. Make a dry run with the saw turned off and check for clearance.
Adjust the fence to be as close to the blade as practical to provide max imum workpiece
support, without interfering with arm up and down movement. Tighten the fence adjustment
knob securely. When the bevel operations are complete, don’t forget to relocate thefence.
For certain cuts, it may be desirable to bring the fences closer to the blade. To use this feature,
back the fence adjustment knobs out two turns and move the fences closer to the blade past
the normal limit, then tighten the fence adjustment knobs to keep the fences in this location.
When using this feature, make a dry cut first to ensure the blade does not contact thefences.
NOTE: The tracks of the fences can become clogged with sawdust. If you notice that they are
becoming clogged, use a brush or some low pressure air to clear the guidegrooves.
Bevel Lock Knob (Fig. A)
The bevel lock knob13 allows you to bevel the saw 49° left or right. To adjust the bevel
setting, turn the knob counterclockwise. The saw head bevels easily to the left or to the right
once the 0° bevel stop28 is in the 0° bevel override position. To tighten, turn the bevel lock
knobclockwise.
0 ° Bevel Override (Fig. A)
The bevel stop override allows you to bevel the saw to the right past the 0°mark.
When engaged, the saw will automatically stop at 0° when brought up from the left.
To move past 0° to the right, pull the 0° bevel stop28, rotate 90° (either clockwise or
counterclockwise) and let go for the spring loaded pin to lock in.
To return the bevel to 0° bevel stop, pull the 0° bevel stop, rotate 90° (either clockwise or
counterclockwise) and let go for the spring loaded pin will lockin.
45 ° Bevel Stop Override (Fig. J)
There are two bevel stop override levers50, one on each side of the saw. To bevel the saw, left
or right, past 45°, push the 45° bevel override lever rearward. When in the rearward position,
13
ENGLISH
Non‑Through‑Cutting (Grooving and Rabbeting)
Instructions in the Crosscuts, Bevel Cuts and Cutting Compound Miters sections are for cuts
made through the full thickness of the material. The saw can also perform non‑through cuts to
form grooves or rabbets in thematerial.
Groove Cut (Fig. A)
Refer to Depth Stop for detailed instructions for setting depth of cut. A piece of scrap wood
should be used to verify the desired depth ofcut.
Hold the wood firmly on the table and against the fence12. Align the cut area underneath
the blade. Position the saw arm fully forward, with blade in down position. Turn on the saw by
squeezing the trigger switch1 shown in FigureA. Smoothly, push saw arm rearward to cut a
groove through the workpiece.
Release the trigger switch with the saw arm down. When saw blade has completely stopped,
raise the saw arm. Always let the blade come to a full stop before raising thearm.
To widen the groove, repeat steps 1–4 until the desired width isobtained.
To cut through an existing pencil line on a piece of wood, match the angle as close as possible.
Cut the wood a little too long and measure from the pencil line to the cut edge to determine
which direction to adjust the miter angle and recut. This will take some practice, but it is a
commonly usedtechnique.
Bevel Cuts (Fig. A)
A bevel cut is a crosscut made with the saw blade leaning at an angle to the wood. In order
to set the bevel, loosen the bevel lock13, and move the saw to the left or right as desired.
(It is necessary to move the fence to allow clearance.) Once the desired bevel angle has been
set, tighten the bevel lock firmly. Refer to the Controls section for detailed instructions on the
bevelsystem.
Bevel angles can be set from 49º right to 49º left and can be cut with the miter arm set
between 50º left or 60º right. At some extreme angles, the right or left side fence might have
to be removed. To remove the left or right fence, unscrew the fence adjustment knob16
several turns and slide the fenceout.
NOTE: Refer to Fence Adjustment in the Adjustments section for important information on
adjusting the fences for certain bevelcuts.
Quality of Cut
The smoothness of any cut depends on a number of variables. Things like material being cut,
blade type, blade sharpness and rate of cut all contribute to the quality of thecut.
When smoothest cuts are desired for molding and other precision work, a sharp (60 tooth
carbide) blade and a slower, even cutting rate will produce the desiredresults.
Ensure that the material does not move or creep while cutting; clamp it securely in place.
Always let the blade come to a full stop before raisingarm.
If small fibers of wood still split out at the rear of the workpiece, stick a piece of masking tape
on the wood where the cut will be made. Saw through the tape and carefully remove tape
whenfinished.
For varied cutting applications, refer to the list of recommended saw blades for your saw and
select the one that best fits your needs. Refer to Saw Blades underAccessories.
Through‑Cutting Operations (Fig. A)
If the slide feature is not used, ensure the saw head is pushed back as far as possible and the
rail lock knob is tightened. This will prevent the saw from sliding along its rails as the workpiece
isengaged.
NOTE: Although this saw will cut wood and many non‑ferrous materials, we will limit our
detailed discussion to the cutting of wood only. The same guidelines apply to the other
materials. DO NOT CUT FERROUS (IRON AND STEEL) MAT ERIALS OR MASONRY WITH THIS SAW.
Do not use any abrasiveblades.
NOTE: Refer to Guard Actuation and Visibility in the Adjustments section for important
information about the lower guard beforecutting.
Crosscuts (Fig. A, Q)
A crosscut is made by cutting wood across the grain at any angle. A straight crosscut is made
with the miter arm at the zero degree position. Set and lock the miter arm at zero, hold the
wood firmly on the table and against the fence. With the rail lock knob tightened, turn on the
saw by squeezing the trigger switch1 shown in FigureA.
When the saw comes up to speed (about 1second) lower the arm smoothly and slowly to cut
through the wood. Let the blade come to a full stop before raising arm.
When cutting anything larger than a 2x 8(51 x 203mm [2 x 6(51 x 152) at 45º miter]) use an
out‑down‑back motion with the rail lock knob loosened. Pull the saw out, toward you, lower
the saw head down toward the workpiece, and slowly push the saw back to complete the cut.
Do not allow the saw to contact the top of the workpiece while pulling out. The saw may run
toward you, possibly causing personal injury or damage to theworkpiece.
Cutting of multiple pieces is not recommended but can be done safely by ensuring that each
piece is held firmly against the table and fence.
NOTE: To provide greater crosscut capacity with reduced stroke, the blade on the DCS781
extends deeper into the table. As a result, a greater lifting force on the workpiece may be
experienced during thecut.
CAUTION: Always use a work clamp to maintain control and reduce the risk of workpiece
damage and personal injury, if your hands are required to be within 4" (100mm) of the
blade during thecut.
NOTE: The rail lock knob30 shown in Figure A must be loose to allow the saw to slide along
its rails24.
Miter crosscuts are made with the miter arm at some angle other than zero. This angle is often
45º for making corners, but can be set anywhere from zero to 50º left or 60° right. Make the
cut as described above.
When performing a miter cut on workpieces wider than a 2x 6that are shorter in length,
always place the longer side against the fence12 (Figure Q).
Dust Extraction (Fig. O)
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
CAUTION: Never operate this saw unless the dust bag or DeWALT dust extractor is
in place. Wood dust may create a breathinghazard.
Your saw has a built‑in dust port that allows an Airlock™ compatible dust collection system
to be connected. Use of a non‑Airlock dust collection system requires the use of the supplied
vacuum adapter.
Our recommended optimal solution:
Vaccuum (DXV14P)
Separator (DXVCS003)
2‑½" x 7' Hose (DXVA19‑2501)
Vacuum Adapter: Used for DXV series vacuums and other non‑Airlock
compatiblevacuums.
To Attach the Dust Bag (Fig. P)
1. Fit the dust bag53 to the dust port17 as shown in FigureP.
To Empty the Dust Bag (Fig. P)
1. Remove dust bag53 from the saw and gently shake or tap the dust bag toempty.
2. Reattach the dust bag back onto the dust port17.
You may notice that all the dust will not come free from the bag. This will not affect cutting
performance but will reduce the saw's dust collection efficiency. To restore your saw's dust
collection efficiency, depress the spring inside the dust bag when you are emptying it and tap
it on the side of the trash can or dustreceptacle.
Trigger Switch (Fig. N)
To turn the saw on, push the lock‑off lever41 to the left, then depress the trigger switch1.
The saw will run while the switch is depressed. Allow the blade to spin up to full operating
speed before making the cut. To turn the saw off, release the switch. Allow the blade to stop
before raising the saw head. There is no provision for locking the switch on. A hole52 is
provided in the trigger for insertion of a padlock to lock the switchoff.
Always be sure the blade has stopped before removing it from thekerf.
Clamping the Workpiece (Fig. A)
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
WARNING: A workpiece that is clamped, balanced and secure before a cut may become
unbalanced after a cut is completed. An unbalanced load may tip the saw or anything the
saw is attached to, such as a table or workbench. When making a cut that may become
unbalanced, properly support the workpiece and ensure the saw is firmly bolted to a stable
surface. Personal injury mayoccur.
WARNING: The clamp foot must remain clamped above the base of the saw whenever
the clamp is used. Always clamp the workpiece to the base of the saw–not to any other
part of the work area. Ensure the clamp foot is not clamped on the edge of the base of
thesaw.
CAUTION: Always use a work clamp to maintain control and reduce the risk of workpiece
damage and personalinjury.
If you cannot secure the workpiece on the table and against the fence by hand, (irregular
shape, etc.) or your hand would be less than 4" (100mm) from the blade, a clamp or other
fixture must beused.
For best results use the vertical material clamp23 provided with your saw. Additional clamps
can be purchased at your local retailer or DeWALT servicecenter.
Other aids such as spring clamps, bar clamps or C‑clamps may be appropriate for certain sizes
and shapes of material. Use care in selecting and placing these clamps. Take time to make a dry
run before making the cut. The left fence will slide from side to side to aid in clamping
To Install Clamp (Fig. A)
1. Insert clamp post into the hole behind the fence12.
2. Adjust the clamp up turning the knob counterclockwise. And clamp down by turning the
knob clockwise. Make sure to firmly clamp theworkpiece.
NOTE: Place the clamp on the opposite side of the base when beveling. ALWAYS MAKE DRY
RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ENSURE THE
CLAMP DOES NOT INTERFERE WITH THE ACTION OF THE SAW ORGUARDS.
completely stopped. ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT
YOU CAN CHECK THE PATH OF THE BLADE. DO NOT CROSS ARMS, AS SHOWN IN FIGUREM.
Keep both feet firmly on the floor and maintain proper balance. As you move the miter arm
left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard
louvers when following a pencilline.
ENGLISH
14
Cutting Crown Molding
Your miter saw is better suited to the task of cutting crown molding than any tool made. In
order to fit properly, crown molding must be compound mitered with extremeaccuracy.
The two flat surfaces on a given piece of crown molding are at angles that, when added
together, equal exactly 90°. Most, but not all, crown molding has a top rear angle (the section
that fits flat against the ceiling) of 52° and a bottom rear angle (the part that fits flat against
the wall) of38°.
Your miter saw has special pre‑set miter latch points at 31.6° left and right for cutting crown
molding at the proper angle and bevel stop pawls at 33.9° left and right. There is also a mark
on the bevel scale at 33.9°.
The chart below gives the proper settings for cutting crown molding. (The numbers for
the miter and bevel settings are very precise and are not easy to accurately set on your
saw.) Since most rooms do not have angles of precisely 90º, you will have to fine tune your
settingsanyway.
PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!
Instructions for Cutting Crown Molding Laying Flat and Using
the Compound Features (Fig. A, U)
1. Molding laying with broad back surface down flat on saw table18.
2. Top of molding against fence12.
3. The settings below are for all standard (U.S.) crown molding with 52° and 38°angles.
Inside corner Outside corner
Left side
1. Bevel left 33.9°
2. Miter table set at right 31.62°
3. Save left end of cut
1. Bevel right 33.9°
2. Miter table set at left 31.62°
3. Save left end of cut
Right side
1. Bevel right 33.9°
2. Miter table set at left 31.62°
3. Save right end of cut
1. Bevel left 33.9°
2. Miter table set at right 31.62°
3. Save right end of cut
When setting bevel and miter angles for all compound miters, remember that:
The angles presented for crown moldings are very precise and difficult to set exactly. Since
they can easily shift slightly and very few rooms have exactly square corners, all settings should
be tested on scrapmolding.
PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!
Alternative Method for Cutting Crown Molding (Fig. V)
Place the molding on the table at an angle between the sliding fence12 and the saw
table18, as shown in FigureV. Use of the crown molding fence accessory (DW7084) is highly
recommended because of its degree of accuracy and convenience. The crown molding fence
accessory is available for purchase from your localdealer.
The advantage to cutting crown molding using this method is that no bevel cut is required.
Minute changes in the miter angle can be made without affecting the bevel angle. This way,
when corners other than 90° are encountered, the saw can be quickly and easily adjusted for
them. Use the crown molding fence accessory to maintain the angle at which the molding will
be on thewall.
Instructions for Cutting Crown Molding Angled Between the
Fence and Base of the Saw for All Cuts
1. Angle the molding so the bottom of the molding (part which goes against the wall when
installed) is against the fence and the top of the molding is resting on the base of the saw,
as shown in FigureV..
2. The angled “flats” on the back of the molding must rest squarely on the fence and base of
thesaw.
Inside corner Outside corner
Left side 1. Miter right 45°
2. Save right side of cut
1. Miter left 45°
2. Save right side of cut
Right side 1. Miter left 45°
2. Save left side of cut
1. Miter right 45°
2. Save left side of cut
Inside corner Outside corner
Left side 1. Miter left 45°
2. Save left side of cut
1. Miter right 45°
2. Save left side of cut
Right side 1. Miter right 45°
2. Save right side of cut
1. Miter left 45°
2. Save right side of cut
Material up to 6.5" (165 mm) can be cut as describedabove.
Cutting Compound Miters (Fig. S)
A compound miter is a cut made using a miter angle and a bevel angle at the same time.
This is the type of cut used to make frames or boxes with slanting sides like the one shown in
FigureR.
NOTE: If the cutting angle varies from cut to cut, check that the bevel lock knob and the miter
lock handle are securely locked. These must be locked after making any changes in bevel
ormiter.
The chart at the end of this manual (Table 1) will assist you in selecting the proper bevel and
miter settings for common compound miter cuts. To use the chart, select the desired angleA
(Fig.S) of your project and locate that angle on the appropriate arc in the chart. From that
point follow the chart straight down to find the correct bevel angle and straight across to find
the correct miterangle.
Set your saw to the prescribed angles and make a few trial cuts. Practice fitting the cut pieces
together until you develop a feel for this procedure and feel comfortable withit.
Example: To make a 4‑sided box with 26º exterior angles (Angle A, Fig.S), use the upper right
arc. Find 26° on the arc scale. Follow the horizontal intersecting line to either side to get miter
angle setting on saw (42°). Likewise, follow the vertical intersecting line to the top or bottom
to get the bevel angle setting on the saw (18°). Always try cuts on a few scrap pieces of wood
to verify the settings on thesaw.
Cutting Trim Molding and Other Frames (Fig. R)
Sketch 2in FigureR shows a joint made by setting the miter arm at 45º to miter the two
boards to form a 90º corner. To make this type of joint, set the bevel adjustment to zero and
the miter arm to 45º. Once again, position the wood with the broad flat side on the table and
the narrow edge against thefence.
The two sketches in FigureR are for four‑sided objectsonly.
As the number of sides changes, so do the miter and bevel angles. The chart below gives the
proper angles for a variety ofshapes.
– EXAMPLES –
NUMBER OF SIDES MITER OR BEVEL ANGLE
4 45°
5 36°
6 30°
7 25.7°
8 22.5°
9 20°
10 18°
The chart assumes that all sides are of equal length. For a shape that is not shown in the chart,
use the following formula: 180º divided by the number of sides equals the miter (if the material
is cut vertically) or bevel angle (if the material is cut layingflat).
Cutting Picture Frames, Shadow Boxes and Other Four‑Sided
Projects (Fig. R)
To best understand how to make the items listed here, we suggest that you try a few simple
projects using scrap wood until you develop a “feel” for yoursaw.
Your saw is the perfect tool for mitering corners like the one shown in FigureR. Sketch1shows
a joint made by using the bevel adjustment to bevel the edges of the two boards at 45º each
to produce a 90º corner. For this joint the miter arm was locked in the zero position and the
bevel adjustment was locked at 45º. The wood was positioned with the broad flat side against
the table and the narrow edge against the fence. The cut could also be made by mitering right
and left with the broad surface against thefence.
Support for Long Pieces
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
ALWAYS SUPPORT LONGPIECES.
Never use another person as a substitute for a table extension; as additional support for a
workpiece that is longer or wider than the basic miter saw table or to help feed, support or pull
theworkpiece.
Support long workpieces using any convenient means such as sawhorses or similar devices to
keep the ends fromdropping.
Cutting Base Molding (Fig. T)
ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANYCUTS.
Straight 90° cuts:
Position the wood against the fence and hold it in place as shown in FigureT. Turn on the saw,
allow the blade to reach full speed and lower the arm smoothly through thecut.
Cutting Base Molding up to 6.5" (165 mm) Vertically Against
the Fence (Fig. L, T)
NOTE: Use the slide lock transport lever61, shown in Figure L1, when cutting base molding
measuring from 3” to 6.5” (76 mm to 165 mm) high vertically against thefence.
Position material as shown in FigureT.
All cuts should be made with the back of the molding against the fence and with the bottom
of the molding against thetable.
15
ENGLISH
Three Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/Legal/Warranty/3‑Year‑Limited‑Warran
ty.
To request a written copy of the warranty terms, contact: Customer Service at DeWALT
Industrial Tool Co., 701East Joppa Road, Towson, MD 21286or call 1‑800‑4‑DeWALT
(1-800-433-9258).
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging,
call the local company or see website for warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1‑800‑4‑DeWALT (1-800-433-9258) for a freereplacement.
Register Online
Thank you for your purchase. Register your product nowfor:
WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with yourproduct.
CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,
your registration of ownership will serve as your proof ofpurchase.
FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer SafetyAct.
Register online at www.dewalt.com.
Repairs
The charger and batteries are notserviceable. There are no serviceable parts inside the charger
or batterypack.
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement, when applicable) should be
performed by a DeWALT factory service center or a DeWALT authorized service center.
Always use identical replacementparts.
Accessories
WARNING: Since accessories, other than those offered by DeWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only DeWALT recommended accessories should be used with thisproduct.
Recommended accessories for use with your tool are available at extra cost from your
local dealer or authorized service center. If you need assistance in locating any accessory,
please contact DeWALT Industrial Tool Co., 701East Joppa Road, Towson, MD 21286, call
1‑800‑4‑DeWALT (1-800-433-9258) or visit our website: www.dewalt.com.
Optional Accessories
The following accessories, designed for your saw, may be helpful. Use care in selecting and
usingaccessories.
Dust Bag: DW7053
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdustproduced.
Crown Molding Fence: DW7084
Used for precision cutting of crownmolding.
Saw Blades
ALWAYS USE 12" (305mm) SAW BLADES WITH 1" (25.4 mm) ARBOR HOLES.SPEED RATING
MUST BE AT LEAST 4800RPM.Never use a smaller diameter blade.It will not be guarded
properly.Use crosscut blades only! Do not use blades designed for ripping, combination
blades or blades with hook angles in excess of 7˚.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
Construction Saw Blades (maximum thin kerf with anti‑stick rim)
General Purpose 12" (305 mm) 32/40
Fine Crosscuts 12" (305 mm) 60
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 12" (305 mm) 80
Non‑ferrous metals 12" (305 mm) 96
NOTE: For cutting non‑ferrous metals, use only saw blades with TCG teeth designed for this purpose.
Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog the dust duct and may prevent
dust from flowing away from the cutting area properly. With the saw unplugged and the saw
head raised fully, low pressure air or a large diameter dowel rod can be used to clear the dust
out of the dustduct.
Worklight Cleaning
For the best worklight performance, perform the following maintenanceregularly.
1. Carefully clean sawdust and debris from worklight lens with a cotton swab.
2. DO NOT use solvents of any kind, they may damage the lens.
3. Dust build‑up can block the worklight and prevent it from accurately indicating the line
ofcut.
4. Follow miter saw’s instruction manual to remove and install blade.
5. With blade removed from saw, clean pitch and build‑up from blade. Pitch and debris can
interfere with the worklight and prevent it from accurately indicating the line ofcut.
SPECIFICATIONS
Light source Power LED
Worklight 6 V DC
Operating Temperature ‑40°F to 221°F (‑40°C to 105°C)
Storage Temperature ‑40°F to 221°F (‑40°C to 105°C)
Environmental Water resistant
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the non‑metallic
parts of the tool. These chemicals may weaken the plastic materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off, and remove
the battery pack before transporting, making any adjustments, cleaning,
repairing, or removing/installing attachments or accessories. An accidental
start‑up can causeinjury.
WARNING: To reduce the risk of serious personal injury, DO NOT touch the sharp
points on the blade with fingers or hands while performing anymaintenance.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.
1. All bearings are sealed. They are lubricated for life and need no furthermaintenance.
2. Periodically clean all dust and wood chips from around AND UNDER the base and the
rotary table. Even though slots are provided to allow debris to pass through, some dust
willaccumulate.
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST
THEFENCE.
Aluminum Cutting (Fig. A, W)
ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM.
These are available at your local DeWALT retailer or DeWALT service center. Certain workpieces,
due to their size, shape or surface finish, may require the use of a clamp or fixture to prevent
movement during the cut. Position the material so that you will be cutting the thinnest cross
section, as shown in FigureW. FigureW also illustrates the wrong way to cut these extrusions.
Use a stick wax cutting lubricant when cutting aluminum. Apply the stick wax directly to the
saw blade39 before cutting. Never apply stick wax to a movingblade.
The wax, available at most hardware stores and industrial mill supply houses, provides proper
lubrication and keeps chips from adhering to theblade.
Be sure to properly secureworkpiece.
Refer to Saw Blades under Accessories for correct sawblade.
Bowed Material (Fig. X, Y)
When cutting bowed material always position it as shown in FigureX and never like that
shown in Figure Y. Positioning the material incorrectly will cause it to pinch the blade near the
completion of thecut.
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw. It should be cut just like wood and CLAMPED
OR HELD FIRMLY TO THE FENCE TO KEEP IT FROM ROLLING. This is extremely important
when making anglecuts.
Cutting Large Material (Fig. Z)
Occasionally you will encounter a piece of wood a little too large to fit beneath the lower
guard. If this occurs, simply place your right thumb on the upper side of the guard and roll the
guard up just enough to clear the workpiece, as shown in Figure Z. Avoid doing this as much
as possible, but if need be, the saw will operate properly and make the bigger cut. NEVER TIE,
TAPE, OR OTHERWISE HOLD THE GUARD OPEN WHEN OPERATING THISSAW.
ENGLISH
16
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE! WHAT’S WRONG? WHAT TO DO
Saw will not start Battery not installed Install battery. Refer to Installing and Removing BatteryPack.
Battery not charged Charge battery. Refer to ChargingProcedure.
Saw overheated Wait several minutes for saw tocool.
Batteries overheated Wait several minutes for batteries tocool.
Saw makes unsatisfactory cuts Dull blade Replace blade. Refer to Changing or Installing a New Saw Blade.
Blade mounted backwards Turn blade around. Refer to Changing or Installing a New Saw Blade.
Gum or pitch on blade Remove blade and clean with coarse steel wool and turpentine or household
ovencleaner.
Incorrect blade for work being done Change the blade type. Refer to Saw Blades under Optional Accessories.
CUTLINE worklight is flashing Battery not charged Charge battery. Refer to ChargingProcedure.
Machine vibrates excessively Saw not mounted securely to stand or
work bench
Tighten all mounting hardware. Refer to Bench Mounting.
Stand or bench on uneven floor Reposition on flat level surface. Refer to Familiarization.
Damaged saw blade Replace blade. Refer to Changing or Installing a New Saw Blade.
Does not make accurate miter cuts Miter scale not adjusted correctly Check and adjust. Refer to Miter Scale Adjustment under Assembly and
Adjustments.
Blade is not square to fence Check and adjust. Refer to Miter Scale Adjustment under Assembly and
Adjustments.
Blade is not perpendicular to table Check and adjust fence. Refer to Bevel Square to Table Adjustment under
Assembly and Adjustments.
Workpiece moving Clamp workpiece securely to fence or glue 120grit sandpaper to fence with
rubbercement.
Kerf plate worn or damaged Take to authorized servicecenter.
Miter pointer not adjusted correctly Check and adjust. Refer to Miter Pointer Adjustment under Assembly
andAdjustments.
Material pinches blade Cutting bowed material Refer to Bowed Material under Special Cuts.
17
ENGLISH
10
10
10
20
20
20
30
30
30
40
40
40
50
50
50
60
60
60
70
70
70
80
80
80
TABLE 1: COMPOUND MITER CUT
(POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
SET THIS MITER ANGLE ON SAW
SQUARE BOX
6‑SIDED BOX
SET THIS BEVEL ANGLE ON SAW
8‑SIDED BOX
ANGLE OF SIDE OF BOX (ANGLE A)
FRANÇAIS
18
d ) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé
de réglage attachée à une partie pivotante de l’outil électrique peut provoquer des
blessurescorporelles.
e ) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de
mieux maîtriser l’outil électrique dans les situationsimprévues.
f ) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de
bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles.
Les vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les
piècesmobiles.
g ) Si des composants sont fournis pour le raccordement de dispositifs de
dépoussiérage et de ramassage, s’assurer que ceux‑ci sont bien raccordés et
utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers engendrés
par lespoussières.
h ) Ne pas laisser votre connaissance acquise suite l’utilisation fréquente des outils
vous permettre de baisser la garde et ignorer les principes de sécurité de l’outil.
Un acte irréfléchi peut causer une blessure grave en une fraction deseconde.
4) Utilisation et entretien d’un outil électrique
a ) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à
l’application. L’outil électrique approprié effectuera un meilleur travail, de façon plus
sûre et à la vitesse pour laquelle il a étéconçu.
b ) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil
électrique dont l’interrupteur est défectueux est dangereux et doit êtreréparé.
c ) Débranchez la fiche de la prise électrique et, si amovible, retirez le bloc‑piles de
l’outil avant d’effectuer tout ajustement, changement et entreposage de celui‑ci.
Ces mesures préventives réduisent les risques de démarrage accidentel de l’outilélectrique.
d ) Ranger les outils électriques hors de la portée des enfants et ne permettre à
aucune personne n’étant pas familière avec un outil électrique ou son mode
d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains
d’utilisateursinexpérimentés.
e ) Gardez les poignées et surfaces d’emprise propres et libres de tout produit
lubrifiant. Vérifier si les pièces mobiles sont mal alignées ou coincées, si des
pièces sont brisées ou présentent toute autre condition susceptible de nuire
au bon fonctionnement de l’outil électrique. En cas de dommage, faire réparer
l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont causés
par des outils électriques malentretenus.
f ) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien
entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles àmaîtriser.
g ) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux
présentes directives en tenant compte des conditions de travail et du travail à
effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour
laquelle il a été conçu estdangereuse.
h ) Garder vos mains et les surfaces de prise sèches, propres et libres de graisse et de
poussière. Les mains et les surfaces de prise glissante ne permettent pas la manutention
et le contrôle sécuritaires de l’outil dans les situationsimprévues.
5) Utilisation et entretien du bloc‑piles
a ) Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant. L’utilisation
d’un chargeur qui convient à un type de bloc‑piles risque de provoquer un incendie s’il est
utilisé avec un autre type de b loc‑piles.
b ) Utiliser les outils électriques uniquement avec les blocs‑piles conçus à cet effet.
L’utilisation de tout autre bloc‑piles risque de causer des blessures ou unincendie.
c ) Lorsque le bloc‑piles n’est pas utilisé, le tenir éloigné des objets métalliques,
notamment des trombones, de la monnaie, des clés, des clous, des vis ou autres
petits objets métalliques qui peuvent établir une connexion entre les deux bornes.
Le court‑circuit des bornes du bloc‑piles risque de provoquer des brûlures ou unincendie.
d ) En cas d’utilisation abusive, le liquide peut gicler hors du bloc‑piles; éviter tout
contact avec ce liquide. Si un contact accidentel se produit, laver à grande eau. Si
le liquide entre en contact avec les yeux, obtenir également des soins médicaux.
Le liquide qui gicle hors du bloc‑piles peut provoquer des irritations ou desbrûlures.
e ) Ne pas utiliser de bloc‑piles ou outil qui a été endommagé ou modifié. Les unités
endommagées ou modifiées peuvent avoir une réaction imprévisible résultant en un
incendie, une explosion ou un potentiel deblessure.
f ) Ne pas exposer de bloc‑piles ou l’outil aux flammes ou à des températures
excessives. L’exposition aux flammes ou à une température au‑dessus de 130°C (265°F)
pourrait causer uneexplosion.
g ) Suivre toutes les instructions de recharge et ne rechargez pas le bloc‑piles
ou l’outil à des températures hors de la plage de température indiquée dans
les instructions. Une recharge non conforme ou à une température hors des limites
spécifiées peut endommager les piles et augmenter le risqued’incendie.
6) Réparation
a ) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant
que des pièces de rechange identiques. Cela permettra de maintenir une utilisation
sécuritaire de l’outilélectriques.
b ) Ne jamais réparer des blocs‑piles endommagés. La réparation de blocs‑piles doit
seulement être effectuée par le fabricant ou les fournisseurs de serviceautorisé.
AVERTISSEMENTS GÉNÉRAUX SUR LA SÉCURITÉ DES OUTILS
AVERTISSEMENT : lisez tous les avertissements de sécurité, toutes les instructions,
les illustrations et les caractéristiques fournis avec cet outil électrique. Ne pas
suivre toutes les instructions comprises aux présentes peut conduire à un choc électrique,
un incendie et/ou des blessuresgraves.
CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES
DIRECTIVES POUR UN USAGE ULTÉRIEUR
Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à
alimentation sur secteur (avec fil) ou par piles (sansfil).
1) Sécurité du lieu de travail
a ) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont
propices auxaccidents.
b ) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en
présence de liquides, de gaz ou de poussières inflammables. Les outils électriques
produisent des étincelles qui pourraient enflammer la poussière ou lesvapeurs.
c ) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil
électrique. Une distraction pourrait en faire perdre la maîtrise àl’utilisateur.
2) Sécurité en matière d’électricité
a ) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais
modifier la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un
outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de
fiches non modifiées correspondant à laprise.
b ) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,
des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est
plus élevé si votre corps est mis à laterre.
c ) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de
l’eau dans un outil électrique augmente le risque de chocélectrique.
d ) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour
transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de
la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons
endommagés ou enchevêtrés augmentent les risques de chocélectrique.
e ) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge
convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur
réduira les risques de chocélectrique.
f ) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit
humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés
d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit
les risques de chocélectrique.
3) Sécurité personnelle
a ) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un
outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue
ou sous l’influence de drogues, d’alcool ou de médicaments. Un simple moment
d’inattention en utilisant un outil électrique peut entraîner des blessures corporellesgraves.
b ) Utiliser des équipements de protection individuelle. Toujours porter une
protection oculaire. L’utilisation d’équipements de protection comme un masque
antipoussière, des chaussures antidérapantes, un casque de sécurité ou des protecteurs
auditifs lorsque la situation le requiert réduira les risques de blessurescorporelles.
c ) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve
à la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou
d’insérer un bloc‑piles, de ramasser ou de transporter l’outil. Transporter un outil
électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique dont
l’interrupteur est à la position de marche risque de provoquer unaccident.
Définitions : symboles et termes d'alarmes sécurité
Les définitions ci‑dessous décrivent le niveau de gravité de chaque mot d'avertissement.
Veuillez lire le manuel de l'outil électrique et prêter attention à cessymboles.
DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée,
entraînera la mort ou des blessuresgraves.
AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas
évitée, pourrait entraîner la mort ou des blessuresgraves.
ATTENTION : indique une situation potentiellement dangereuse qui, si elle n’est pas
évitée, pourrait entraîner des blessures légères oumodérées.
(Si utilisé sans aucun terme) Indique un message propre à lasécurité.
AVIS : indique une pratique ne posant aucun risque de dommages corporels
mais qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de
dommagesmatériels.
Utilisation prévue
Cette scie à onglets robuste est conçue pour les applications de coupe du
boisprofessionnelles.
Cette scie à onglets est un outil électrique professionnel.
NE PAS utiliser en conditions humides ou en présence de liquides ou de gazinflammables.
NE PAS laisser les enfants entrer en contact avec l’outil. Une supervision est requise lorsque
des utilisateurs inexpérimentés utilisent cetoutil.
Français (traduction de la notice d’instructions originale)
AVERTISSEMENT : lire tous les avertissements de sécurité et toutes les directives.
Le non‑respect des avertissements et des directives pourrait se solder par un choc
électrique, un incendie et/ou une blessuregrave.
AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi del’outil.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

DeWalt DCS781 Manuel utilisateur

Catégorie
Scies à onglet
Taper
Manuel utilisateur

dans d''autres langues