WTI PTS Series Guide de démarrage rapide

Taper
Guide de démarrage rapide
WTI Part No.: 14124
Rev. D
PTS Series
Automatic Power Transfer Switch
Quick Start Guide
Warnings and Cautions:
Installation Instructions
Secure Racking
If Secure Racked units are installed in a closed or multi-unit rack assembly, they may require further
evaluation by Certication Agencies. The following items must be considered.
1. The ambient within the rack may be greater than room ambient. Installation should be such that the
amount of air ow required for safe operation is not compromised. The maximum temperature for the
equipment in this environment is 55°C. Consideration should be given to the maximum rated ambient.
2. Installation should be such that a hazardous stability condition is not achieved due to uneven loading.
Input Supply
Check nameplate ratings to assure there is no overloading of supply circuits that could have an eect on
overcurrent protection and supply wiring.
Grounding
Reliable earthing of this equipment must be maintained. Particular attention should be given to supply
connections when connecting to power strips, rather than direct connections to the branch circuit.
No Serviceable Parts Inside; Authorized Service Personnel Only
Do not attempt to repair or service this device yourself. Internal components must be serviced by authorized
personnel only.
• ShockHazard-DoNotEnter
Disconnect Power
If any of the following events are noted, immediately disconnect the unit from the outlet and contact
qualied service personnel:
1. If the power cord becomes frayed or damaged.
2. If liquid has been spilled into the device or if the device has been exposed to rain or water.
Two Power Supply Cables
Note that PTS Series units feature two separate power circuits, and a separate power supply cable for each
power circuit. Make certain to disconnect both power supply cables before attempting to service or remove
the unit.
15-Amp "Starter" Cable
Depending on your specic model, PTS Series units may be shipped with either one or two 125 VAC,
15 Amp "Starter" Cables. These Starter Cables will allow you to connect the PTS to power for bench
testing and initial start up and are adequate for applications that only require 15 Amps. For 20-Amp power
switching applications, please refer to the WTI Power Cable guide supplied with the unit, or use appropriate
20-Amp cables.
Units with Attached Power Supply Cable(s)
For units with xed Power Cords the socket-outlet shall be installed near the equipment and shall be easily
accessible.
Restricted Access Location
Equipment is intended for installation in Restricted Access Location.
Les matériels sont destinés à être installés dans des EMPLACEMENTS À ACCÈS RESTREINT.
Page 3
1. Introduction
This Quick Start Guide describes the installation procedure for the PTS series
hardware. The PTS is essentially a power fallback switch, that automatically
switches power from a primary input to a secondary input when power to the primary
input is lost or interrupted.
2. Hardware Installation
Mounting Instructions
HorizontalMountPTSModels: Horizontal Mount PTS models that are less than
17 inches wide include brackets for wall mounting. Note that optional rack mounting
brackets are also available for all PTS models.
VerticalMountPTSModels: Vertical PTS models include both button mounting
hardware and bracket mounting hardware. The mounting method chosen will usually
depend on the nature of equipment rack in which the vertical PTS will be mounted.
For more information, please refer to the "Vertical Mount Power Devices Rack
Mounting Options" document, which can be found on the WTI website at:
https://www.wti.com/guides/vert-mount-power-device-options.pdf
Page 4
PTS Series; Quick Start Guide
Apply Power to the PTS
Refer to the warnings and cautions at the beginning of this guide and the power rating
nameplate on the PTS back panel, and then connect the unit to two appropriate power
sources. For units with detachable power input cables, connect the power input
cables to the power inlets, install the cable keepers, and then connect the primary
power input cable to your primary power supply and the secondary power input cable
to your secondary power supply.
Notes:
After connecting your power cables to the PTS unit, make certain to
secure the cables in order to prevent accidental disconnection.
PTS-1 series units are designed for switching power input lines that are
typically 120 VAC. If a power input higher than 140 VAC is connected to
a PTS-1 unit, then power switching features will not function correctly.
PTS-2 series units are designed for switching power input lines that are
typically 240 VAC. If a power input lower than 190 VAC is connected to
a PTS-2 unit, then power switching features will not function correctly.
Page 5
PTS Series; Quick Start Guide
3. Operation
When properly installed, the PTS will automatically switch power from the primary
input to the secondary input when the power to the primary input is interrupted.
After switching from primary to secondary, the PTS will also switch power back to
the primary input when power to the primary input is restored. Note that the "Input
Power" LEDs on the PTS front panel will light to indicate which power input is
active. If the "Primary" LED is lit, this indicates that the Primary Power source is
active; if the "Secondary" LED is lit, this indicates that the Secondary power source
is active.
Page 6
PTS Series; Quick Start Guide
Notes:
FCC Part 15 Regulation
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Plug the equipment into an outlet on a circuit that is dierent from the one used by the receiver.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the
following conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference that may cause undesired operation.
WARNING:Changesormodicationstothisunitnotexpresslyapprovedbythe
partyresponsibleforcompliancecouldvoidtheusersauthoritytooperatethe
equipment
EMC and Safety Directive Compliance
The CE mark is axed to this product to conrm compliance with the following European
Community Directives:
Council Directive 2014/30/EU of 26 February 2014 on the approximation of the laws of
Member States relating to electromagnetic compatibility;
and
Council Directive 2014/35/EC of 26 February 2014 on the harmonization of the laws of
Member States relating to electrical equipment designed for use within certain voltage limits;
Industry Canada - EMI Information
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
5 Sterling • Irvine • California 92618
(949) 586-9950 • Toll Free: 1-800-854-7226
Fax: (949) 583-9514 • www.wti.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

WTI PTS Series Guide de démarrage rapide

Taper
Guide de démarrage rapide

dans d''autres langues