Wacker Neuson LTW20Z3 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Light Tower Wide Body

Tour d’éclairage corps large

LTW20Z-1

LTW20Z-3

Type LTW20Z-1, LTW20Z-3

Document 5000187567

Date

0817

Version

09

Language EN-FR

5000187567

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

LTW 20Z Foreword

wc_tx001055gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered by

this manual

This manual covers machines with the following item numbers:

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

LTW 20Z-1 0620375, 0620842, 5200004096, 5200004205, 5200024872

LTW 20Z-3 0620376, 0620843, 5200003583, 5200004097

LTW 20Z-1 T4f 5200014324, 5200014326, 5200014328, 5200018239

LTW 20Z-3 T4f 5200014325, 5200014327, 5200014329, 5200023604

wc_gr01088

5

LTW 20Z3

LTW 6K, LTW 8K, LTW20Z1

Serial Number:

Foreword LTW 20Z

4 wc_tx001055gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Table of Contents

LTW 20Z

wc_bo5000187543_08TOC.fm

5

Foreword 3

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Lamp Safety ....................................................................................... 12

1.5 Operator Safety while Using Internal Combustion Engines ............... 13

1.6 Safety Guidelines for Towing the Machine ......................................... 14

1.7 Service Safety .................................................................................... 15

2 Labels 17

2.1 Label Locations .................................................................................. 17

2.2 Label Meanings .................................................................................. 19

3 Lifting and Transporting 32

3.1 Before Towing Checklist ..................................................................... 33

3.2 Lifting and Tie-Down Points ............................................................... 34

3.3 Testing the Breakaway System (Electric Brakes) .............................. 35

3.4 Testing the Breakaway System (Hydraulic Surge Brakes) ................. 37

4 Operation 39

4.1 Preparing the Machine for First Use ................................................... 39

4.2 Positioning the Machine ..................................................................... 40

4.3 Grounding the Light Tower ................................................................. 41

4.4 Leveling Trailer ................................................................................... 42

4.5 Refueling the Machine ........................................................................ 43

4.6 Control Panel - Lights ......................................................................... 44

4.7 Control Panel - Power Winch ............................................................. 44

4.8 Engine Control Module - T4i ............................................................... 45

4.9 Engine Control Module - T4f .............................................................. 46

4.10 Machine Monitoring ............................................................................ 47

4.11 Alarms and Shut-Down Conditions .................................................... 49

4.12 Resetting the Maintenance Timers ..................................................... 51

4.13 Raising the Tower (Manual Winch System) ....................................... 52

4.14 Lowering the Tower (Manual Winch System) ..................................... 55

4.15 Meanings of Genset Controller Indicator Lights ................................. 57

4.16 Adjusting the Lights ............................................................................ 59

Table of Contents

LTW 20Z

wc_bo5000187543_08TOC.fm

6

4.17 Raising the Tower (Power Winch System) ..........................................60

4.18 Lowering the Tower (Power Winch System) ......................................63

4.19 Starting the Machine ...........................................................................65

4.20 Stopping the Machine ..........................................................................66

4.21 Auto Mode (Remote Run) ...................................................................66

4.22 Generator Derating ..............................................................................66

4.23 Receptacle Panel ................................................................................67

4.24 Load Balancing ....................................................................................69

4.25 Electronic Governor .............................................................................70

4.26 Emergency Stop Switch ......................................................................70

5 Factory-Installed Options 71

5.1 Available Options ................................................................................71

5.2 LED Lights ...........................................................................................74

5.3 Using the Internal Light Storage ..........................................................75

5.4 Cold Weather Options .........................................................................77

5.5 North Slope Options ............................................................................78

6 Maintenance 80

6.1 Periodic Maintenance Schedule ..........................................................80

6.2 Installing / Removing Light Fixtures ....................................................82

6.3 Replacing / Removing Lamps .............................................................83

6.4 Daily Inspection ...................................................................................84

6.5 Checking Engine Coolant ....................................................................85

6.6 Servicing the Air Cleaner .....................................................................86

6.7 Changing the Engine Oil .....................................................................87

6.8 Maintaining the Fuel/Water Separator .................................................89

6.9 Maintaining the Trailer .........................................................................90

6.10 Long-Term Storage .............................................................................91

7 Maintenance Tier 4f Engines: Isuzu 93

8 Troubleshooting 99

9 Technical Data 101

9.1 Engine - T4i .......................................................................................101

9.2 Engine - T4f .......................................................................................102

9.3 Generator ..........................................................................................103

Table of Contents

LTW 20Z

wc_bo5000187543_08TOC.fm

7

9.4 Machine - Tier 4i ............................................................................... 104

9.5 Machine - Tier 4f .............................................................................. 105

9.6 Dimensions ....................................................................................... 106

9.7 Radiation Compliance ...................................................................... 106

Tire Safety Information 107

Introduction to Tire Safety Information ............................................. 107

10 Schematics 119

10.1 LTW 20Z-1—Electrical Schematic T4i ............................................. 120

10.2 LTW 20Z-1—Electrical Schematic Components .............................. 121

10.3 LTW 20Z-3—Electrical Schematic T4i ............................................. 122

10.4 LTW 20Z-3—Electrical Schematic Components .............................. 123

10.5 LTW 20Z-1—Electrical Schematic T4f ............................................. 124

10.6 LTW 20Z-1—Electrical Schematic Components - T4f ...................... 125

10.7 LTW 20Z-3—Electrical Schematic T4f ............................................. 126

10.8 LTW 20Z-3—Electrical Schematic Components - T4f ...................... 127

10.9 Engine Wiring - T4i ........................................................................... 128

10.10 Engine Wiring Components - T4i ..................................................... 129

10.11 Engine Wiring - T4f ........................................................................... 130

10.12 Engine Wiring Components - T4f ..................................................... 131

10.13 Trailer Wiring (Electric Brakes) ......................................................... 132

10.14 Trailer Wiring Components (Electric Brakes) ................................... 132

10.15 Trailer Wiring (Electric Brakes) - Rear Hitch Option ........................ 133

10.16 Trailer Wiring Components (Electric Brakes) ................................... 133

10.17 Trailer Wiring (Surge Brakes / No Brakes) ....................................... 134

10.18 Trailer Wiring (Surge Brakes / No Brakes) - Rear Hitch Option ....... 135

Table of Contents

LTW 20Z

wc_bo5000187543_08TOC.fm

8

wc_si000301gb.fm

9

LTW 20Z Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000301gb.fm

10

Safety Information LTW 20Z

1.2 Machine Description and Intended Use

This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light

Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a

control panel, and an electric alternator. A telescoping tower with four metal halide

lights is mounted to the top of the cabinet. Dual winches tilt, raise, and lower the

telescoping tower. As the engine runs, the generator converts mechanical energy

into electric power. The metal halide lights run off this power. Receptacle(s) are

also present to power auxiliary loads. The operator uses the control panel to

operate and monitor the machine.

This machine is intended for the illumination of outdoor areas. This machine is also

intended for the purpose of supplying electrical power to connected loads. Refer to

the product specifications for the output voltage and frequency of this Light Tower,

and for the maximum output power limit of this Light Tower.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

 The following are some examples of misuse:

 Connecting a load that has voltage and frequency requirements that are

incompatible with the machine output

 Overloading the machine with a device that draws excessive power during

either continuous running or start-up

 Operating the machine in a manner that is inconsistent with all federal, state and

local codes and regulations

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines (unless factory equipped)

 Using the machine as a hoist or hanging items from the tower

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Heat from the lights

 Ultraviolet radiation from the lights

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Electric shock and arc flash

 Personal injury from improper lifting the trailer tongue

wc_si000301gb.fm

11

LTW 20Z Safety Information

 Glare from lights (lights may blind drivers of nearby motor vehicles if the lights

are incorrectly positioned)

 Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Work area

 Make sure the area immediately surrounding the Light Tower is clean, neat, and

free of debris.

 The tower extends up to 9 m (30 ft). Make sure the area above the trailer is

open and clear of overhead wires and obstructions.

Machine

setup

 Make sure the machine is on a firm, level surface and will not tip, roll, slide, or

fall while operating.

 Make sure the machine is well-grounded and securely fastened to a good

earthen ground per national and local regulations.

 The trailer must be leveled and the outriggers extended before raising the tower.

The outriggers must be extended while the tower is up.

 Never connect the machine to other power sources, such as supply mains of

power companies.

Machine

integrity

 Do not start a machine in need of repair.

 Do not use the machine if the insulation on any electrical cord is cut or worn

through.

wc_si000301gb.fm

12

Safety Information LTW 20Z

 Do not operate the lights without the protective lens cover in place or with a lens

cover that is cracked or damaged.

 Replace or repair electrical components with components that are identical in

rating and performance to the originals.

While

operating the

machine

 Keep the area behind the trailer clear of people and obstructions while raising

and lowering the tower.

 Do not raise the tower or operate the machine in high winds. Lower the tower

immediately if high winds or electrical storms are expected in the area.

 Do not raise, lower, or turn the tower while the unit is operating.

 If any part of the tower hangs up, or the winch cable develops slack while raising

or lowering the tower, STOP immediately! Contact an authorized Wacker

Neuson service representative.

 Do not disengage the tower locking pin while the tower is up.

 Lamps become extremely hot in use! Allow the lamps and fixtures to cool 10–15

minutes before handling.

 Lower the tower when not in use.

1.4 Lamp Safety

Description

The lamps provided with your Light Tower are electric discharge lamps. They are

designed for use with metal halide ballasts only, and require time to reach full

brightness on initial startup and after a power interruption. These lamps comply

with FDA regulation performance standards 21 CFR 1040-30.

Operating

safety

 Replace damaged lamps according to the instructions in section Removing /

Replacing Lamps.

 Alternative lamps that automatically extinguish when the outer envelope is

broken or punctured are commercially available.

WARNING

Personal injury hazard. Broken or punctured lamps can cause serious skin burns

and eye inflammation from shortwave ultraviolet radiation.

f Do not operate the Light Tower if a lamp is damaged.

f Replace damaged lamps immediately.

wc_si000301gb.fm

13

LTW 20Z Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Re-install the fuel tank cap after refueling.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000301gb.fm

14

Safety Information LTW 20Z

1.6 Safety Guidelines for Towing the Machine

When towing the machine:

 Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are

damaged.

 Do not tow the machine if any of the trailer’s lug nuts are missing.

 Do not tow the machine if the trailer’s tires have less than 1.5 mm (1/16 inch) of

tread.

 Do not tow the machine unless the trailer’s brakes are functioning properly.

 Do not exceed the trailer manufacturer’s speed limitations.

When towing the machine:

 Only tow the machine when the trailer’s lug nuts are properly torqued.

 Only tow the machine when the trailer’s tires are properly inflated.

 Only tow the machine when all trailer lights are functioning correctly.

 Only tow the machine when the trailer’s safety chains are connected to the

towing vehicle in a crisscross pattern.

 Maintain extra distance between the towing vehicle and other vehicles.

 Avoid soft shoulders, curbs, and sudden lane changes.

 Abide by all licensing requirements for your area.

If you have not driven a towing vehicle with trailer before, practice turning,

stopping, and backing up the towing vehicle with trailer in an area away from traffic.

Only drive the towing vehicle with trailer when you are confident in your ability to do

so.

WARNING

Risk of severe injury or death. Improper trailer condition and towing technique can

lead to an accident.

f Obey the trailer manufacturer’s instructions and the instructions below to reduce

the risk of an accident.

wc_si000301gb.fm

15

LTW 20Z Safety Information

1.7 Service Safety

Precautions

 To reduce the risk of personal injury, read and understand the service

procedures before performing any service to the machine.

 All adjustments and repairs MUST be completed before operation. Do not

operate the machine with a known problem or deficiency! All repairs and

adjustments should be completed by a qualified technician.

 Do not service the machine if your clothing or skin is wet.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Before

servicing the

machine

 Turn the engine off before performing maintenance or making repairs.

 Make sure the engine start switch is turned to OFF.

 Make sure the circuit breakers are open (off).

 Make sure the negative terminal on the battery is disconnected.

 Do not perform even routine service (oil / oil filter changes, cleaning, etc.) unless

all electrical components are shut down.

 Make sure water has not accumulated around the base of the machine. If water

is present, move the machine and allow it to dry before servicing.

 If the machine must be started while servicing, keep hands, feet, and loose

clothing away from moving parts on the generator and engine.

Safety

devices and

modifications

 Replace all safety devices and guards after repair and maintenance.

 Do not modify the machine without the express written approval of the

manufacturer.

Replacing

parts and

labels

 Replace worn or damaged components.

 Use only spare parts recommended by Wacker Neuson.

 Replace all missing and hard-to-read labels.

 Check all external fasteners at regular intervals.

WARNING

High voltage! This machine produces high voltage capable of causing serious injury

or death.

f Only a qualified electrician should troubleshoot or repair electrical problems

occurring with this machine.

wc_si000301gb.fm

16

Safety Information LTW 20Z

Lifting and

transporting

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks and other types of lifting devices

are attached securely and have enough weight-bearing capacity to lift or hold

the machine safely.

 Remain aware of the location of other people when lifting the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being hoisted or moved.

 Do not get onto the machine while it is being hoisted or moved.

LTW 20Z Labels

wc_si000386gb.fm 17

2 Labels

2.1 Label Locations

wc_gr006242

12

BB

OO

DDRR

DD

K

BB

DD

F

CC

L

V

LL

NN

SS

LL

W

FF

D

FF

DD

B

Y

UU

Labels LTW 20Z

18 wc_si000386gb.fm

wc_gr006243

BB

Q

R

O

B

DD

GG

J

C

N

FF

D

IG

FF

E

U

V

S

A

H

HH

T

J

MM

PP

SS

JJ

T

AA

QQ

NN

KK

TT

LTW 20Z Labels

wc_si000386gb.fm 19

2.2 Label Meanings

A

WARNING

Automatic locking pin.

A non-secured, falling tower can cause serious

injury or death if a person is hit. To secure tower,

verify automatic locking pin has been engaged.

B

WARNING

Avoid crushing area.

C

DANGER

Contact with overhead electrical power lines will

cause serious injury or death. Do not position

Light Tower under electrical power lines.

WARNING

Completely lower tower BEFORE tilting tower.

Tilting an extended tower can cause serious

injury or death.

D

NOTICE

Lifting point

Labels LTW 20Z

20 wc_si000386gb.fm

E

WARNING

Secure tower in transport lock before lifting or

towing. A loose swinging tower could cause per-

sonal injury or machine damage.

F

DANGER

Using a light tower indoors CAN KILL YOU IN

MINUTES. Light tower exhaust contains carbon

monoxide. This is a poison you cannot see or

smell.

NEVER use inside a home or garage, EVEN IF

doors and windows are open.

Only use OUTSIDE and far away from windows,

doors, and vents.

G

DANGER

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area unless adequate

ventilation, through such items as exhaust

fans or hoses, is provided.

 Read the Operator’s Manual.

 No sparks, flames, or burning objects

near the machine.

 Stop the engine before refueling.

La page charge ...

Wacker Neuson LTW20Z3 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson LTW20Z3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents